Search Results

Search found 20043 results on 802 pages for 'password assistant mac'.

Page 680/802 | < Previous Page | 676 677 678 679 680 681 682 683 684 685 686 687  | Next Page >

• How to troubleshoot ethernet port on laptop

  - by Psallas Vassilios

  I have a problem with my wired connection. To be more specific, my laptop doesn't seems to recognize that I have plugged in an ethernet cable. I tried to download new drivers for my ethernet card, but I couldn't find any solutions. Maybe because I am new to Linux, so I'm not familiar with running commands in the terminal. OK I have typed the command and here are the results: 00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02) For the second reply I don't know if the following is what you asked me: ?Memory: 3.9 GiB ?Processor: Intel Core 2 Duo CPU P8800 @ 2.66GHz × 2 ?OS type: 32-bit My Ethernet connection had some problem on Windows too. I have changed recently my internet provider, and since then my ethernet cable is not recognized by the laptop. At that time I was still on Windows. I thought that with Ubuntu the problem would be solved, but unfortunately the problem still persists. If someone can help me to solve my problem I'll be thankful. Here are the results of the three first commands you told me to run: lsmod | grep sis190 sis190 22570 0 sudo modprobe sis190 ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:90:81:7e UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:185 errors:0 dropped:0 overruns:0 frame:0 TX packets:185 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22672 (22.6 KB) TX bytes:22672 (22.6 KB) wlan0 Link encap:Ethernet HWaddr 00:25:d3:2c:3a:ae inet addr:192.168.1.72 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe2c:3aae/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:260 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:71992 (71.9 KB) TX bytes:52000 (52.0 KB) and the results of running the last two commands: dmesg | grep -e eth -e sis190 [ 0.816667] sis190: sis190 Gigabit Ethernet driver 1.4 loaded [ 0.816728] sis190 0000:00:04.0: setting latency timer to 64 [ 0.816751] sis190: 0000:00:04.0: Read MAC address from EEPROM [ 0.904032] sis190: 0000:00:04.0: Realtek PHY RTL8201 transceiver at address [ 1.416030] sis190: 0000:00:04.0: Using transceiver at address 1 as default [ 1.448235] sis190 0000:00:04.0: eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at f8410000 (IRQ: 19), 00:90:f5:90:81:7e [ 1.448238] sis190 0000:00:04.0: eth0: GMII mode. [ 1.448243] sis190 0000:00:04.0: eth0: Enabling Auto-negotiation [ 11.560907] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372019] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372265] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.424038] sis190 0000:00:04.0: eth0: auto-negotiating... nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: sis190 State: unavailable Default: no HW Address: 00:90:F5:90:81:7E Capabilities: Carrier Detect: yes Wired Properties Carrier: off

  Read the article

• Microsoft Azure News: Capturing VM Images

  - by Herve Roggero

  Originally posted on: http://geekswithblogs.net/hroggero/archive/2014/05/21/microsoft-azure-news-capturing-vm-images.aspxIf you have a Virtual Machine (VM) in Microsoft Azure that has a specific configuration, it used to be difficult to clone that VM. You had to sysprep the VM, and clone the data disks. This was slow, prone to errors, and stopped you from being productive. No more! A new option, called Capture, allows you to easily select a VM, running or not. The capture will copy the OS disk and data disks and create a new image out of it automatically for you. This means you can now easily clone an entire VM without affecting productivity.  To capture a VM, simply browse to your Virtual Machines in the Microsoft Azure management website, select the VM you want to clone, and click on the Capture button at the bottom. A window will come up asking to name your image. It took less than 1 minute for me to build a clone of my server. And because it is stored as an image, I can easily create a new VM with it. So that’s what I did… And that took about 5 minutes total.  That’s amazing…  To create a new VM from your image, click on the NEW icon (bottom left), select Compute/Virtual Machine/From Gallery, and select My Images from the left menu when selecting an Image. You will find your newly created image. Because this is a clone, you will not be prompted for a new login; the user id/password is the same. About Herve Roggero Herve Roggero, Microsoft Azure MVP, @hroggero, is the founder of Blue Syntax Consulting (http://www.bluesyntaxconsulting.com). Herve's experience includes software development, architecture, database administration and senior management with both global corporations and startup companies. Herve holds multiple certifications, including an MCDBA, MCSE, MCSD. He also holds a Master's degree in Business Administration from Indiana University. Herve is the co-author of "PRO SQL Azure" and “PRO SQL Server 2012 Practices” from Apress, a PluralSight author, and runs the Azure Florida Association.

  Read the article

• Update Errors in Xubuntu 12.10

  - by wil

  I updated by computer from 12.04 to 12.10 and after I finished updating when I turned on my computer I am unable to update my computer. I tried install a new copy of 13.04 but my cpu doesn't support pae. I have a IBM Thinkpad T42 with a 1.7 gigahertx Cpu. When updating through terminal This is the output. sudo apt-get upgrade: [sudo] password for wil: Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: linux-image-extra-3.5.0-34-generic : Depends: linux-image-3.5.0-34-generic but it is not installed linux-image-generic : Depends: linux-image-3.5.0-34-generic but it is not installed E: Unmet dependencies. Try using -f. sudo apt-get upgrade -f: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following NEW packages will be installed: linux-image-3.5.0-34-generic 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. 3 not fully installed or removed. Need to get 0 B/11.8 MB of archives. After this operation, 25.9 MB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 191530 files and directories currently installed.) Unpacking linux-image-3.5.0-34-generic (from .../linux-image-3.5.0-34-generic_3.5.0-34.55_i386.deb) ... This kernel does not support a non-PAE CPU. dpkg: error processing /var/cache/apt/archives/linux-image-3.5.0-34-generic_3.5.0-34.55_i386.deb (--unpack): subprocess new pre-installation script returned error exit status 1 No apport report written because MaxReports is reached already Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.5.0-34-generic /boot/vmlinuz-3.5.0-34-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.5.0-34-generic /boot/vmlinuz-3.5.0-34-generic Errors were encountered while processing: /var/cache/apt/archives/linux-image-3.5.0-34-generic_3.5.0-34.55_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) wil@wil-ThinkPad-T42:~/Desktop$

  Read the article

• Which programming language to get into?

  - by user602479

  I'm ending my third term in a few weeks so I have some spare time coming up. I'd like to spend it seriously digging into programming. My problem: I'm not sure which language to begin with. Just to be clear, I don't want to start a language-y-compared-to-language-z discussion. There are a some other issues that play a major role. In my 5th term I'm going to be participating in a major practical course which will include either Java or C programming. It will take a lot of time and energy, as I found out while talking to a few students who passed the final exams (only 15% pass on their first try). Which practical course I will take is randomly decided. My skills so far are the absolute basics of Java and C programming. I know the different data types and how to handle them, objects, pointers, thread programming, etc. All of that is on a very low level, though. My question now is, what language should I start seriously practicing? Java: I did my first GUIs with this language. I'm familiar with Eclipse but I need a project to work on (which I don't have) to really keep me pushing. Besides that, I don't think it would help me if I have to do C in a year. C: As with Java, I can't think of a personal project to keep me working and keep me interested in programming. If I get assigned to Java in a year, this wouldn't give me any advantages either, would it? (No objects, etc.) Objective-C: I recently came up with this idea. I have a Mac; I'm not really familiar with Xcode but I have one or two personal projects I'd like to work on. Further, I would be working with objects (as in Java) and C language constructs which would both be great for this practical course in a year. What do you think I should begin with? Should I just stick to Java and hope for the best, force myself through C or start (nearly) completely from the beginning with Objective C? Maybe you folks could give me some good advice that would stop me from switching from one language to the next?

  Read the article

• [EF + Oracle] Intro

  - by JTorrecilla

  Prologue I have a busy personal and working time, and at this moment that I start to get more free time, I decided to start a Serie about Entity Framework with Oracle. A few time ago, I got my first experience with EF and Oracle with Oracle 10 g express and Oracle 10 g with the same results, Doesn’t work. Now I download Oracle 11 g to Test again. Tools To start using EF with Oracle we need the following: 1. Visual Studio 2010. No Express Edition 2. Oracle 11g 3 Oracle Driver for EF (ODAC) Intro People, who are starting with EF developments, I recommend to take a look into Unai Zorrilla’s Blog, the post were written in Spanish but they are great! To this Serie, we are going to define the DB from the Oracle administrator. For that we need to follow the next steps: 1. Create a User with a PassWord. In my example the user will be Jtorrecilla 2. Create a TableSpace 3. Define some example tables   (Image1) When we have created the DB, we are going to start a new project in VS 2010. I will start a C# Project. To start with EF, we need to add a new objet to our Project “ADO .NET Entity Data Model". (Image2) The next step will be to indicate that our model will be based on an existing DB, and indicate the connection string (Images 3 and 4): (Imagen3) (Imagen4) Once we selected the connection string, we will need to indicate that in the connection will be saved “Sensitive” data (Image 5), and in the next step we are going to select the DB objets to use in the project(Image 6).   (Image 5) (Image 6) A the end of the selection, we will press Finish button, and it will generate a EDMX file to add to our solution, and in the IDE will appear the DB Schema with the selected Tables and Relations. (Imagen7) One Entity is composed by a set of properties (each matches with a column from the Table in the DB) and Navigation Properties that represents any relation with other Entities.   Finally With this chapter we have installed the environment, defined a DB and configured the solution to start using EF with Oracle. In the next chapter we are going to see What is a Entity and how it works. I hope you enjoy this Serie!

  Read the article

• Unable to ping inside or outside network with default gateway 0.0.0.0

  - by agentroadkill

  I've been around here before and I could usually piece together everything to more or less get myself up and running, but this time I'm truly stumped. I'm trying to connect my new 14.04 install to a network, and I'm forced to be behind my college's router. Now I've tested the vary cable that is right now plugged into my Ubuntu box on a Windows, Mac OS X, and even my friend's Ubuntu 14.04 box, and they all connect no problem. I've been trying to track this down for about two days, but every time I get close to it, the bug jumps to some other piece of my connection. Anyway, as it sits ifconfig -a gives: eth2 Lninkencap:Ethernet HWaddr:00:1f:bc:08:31:1d inet addr:10.32.51.51 Bcast:10.32.51.155 Mask: 255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 RX bytes:0 TX bytes:0 as well as the local loopback, but I'm assuming that is not an issue here. sudo dhclient -v eth2 returns: Listening on LPF/<hardware address of my integrated NIC, above> Sending on <same> Sending on Socket/fallback DHCPREQUEST of 10.32.51.51 on eth2 to 255.255.255.255 port 67 (xid=0x6f4a66ba) <two more lines of same> DHCPDISCOVER on eth2 to 255.255.255.255 port 67 interval 3 (xid=0x156f9fb4) <many more of above with varying intervals> No DHCPOFFERS received. Trying recorded lease 10.32.51.51 RTNETLINK answers: File exists bound: renewal in <large number> seconds If I then try ping 8.8.8.8, I get: connect: Network is unreachable /etc/resolv.conf only contains the two lines telling you not to edit it, while /etc/network/interfaces only has the loopback interface block in it. I've tried commenting out the "option rfc3442" line in /etc/dhcp/dhclient.conf which seemed to fix this issue for many people, as well as adding the line send vendor-class-indentifier "MSFT5.0" to dhclient.conf as well to tell the router I'm a windows box, in case they don't like Linux. Finally, route -n reveals: Destination Gateway Genmask Flags Metric Ref Use Iface 10.32.51.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 I would like to apologize in advance for the doubtless butchered text alignment, but I'm obviously typing this all by hand, reading from the terminal as I type commands. I'm hoping this is an interesting problem, and not something I blithely stumbled past in my (apparent) over-confidence. TIA! Quick addendum before posting: The activity light on the ethernet port are lit and one blinks during boot, but they rarely (and seemingly randomly) do so afterwards (both are dark) even while running dhclient in the foreground. When I had the Ubuntu box tethered to my MacBook earlier, I got what looked like a normal power/uplink blinking pattern, but was unable to ping one from the other.

  Read the article

• Please Help Me Install Firestorm?

  - by Elle Caszatt

  I have been trying for hours just to install one program. In this time, I've tried my best to follow directions and not screw everything up but I have. I'm new to Linux. I tried to install Firestorm and this is what happened: parent@ubuntu:~$ sudo '/home/parent/Downloads/Phoenix_Firestorm-Release_i686_4.2.1.29803/install.sh' [sudo] password for parent: Enter the desired installation directory [/opt/firestorm-install]: /home/parent/downloads - Installing to /home/parent/downloads /home/parent/Downloads/Phoenix_Firestorm-Release_i686_4.2.1.29803/install.sh: line 80: /home/parent/downloads/etc/refresh_desktop_app_entry.sh: Permission denied parent@ubuntu:~$ sudo opt/firestorm-install sudo: opt/firestorm-install: command not found parent@ubuntu:~$ ./etc/refresh_desktop_app_entry.sh bash: ./etc/refresh_desktop_app_entry.sh: No such file or directory parent@ubuntu:~$ sudo '/home/parent/Downloads/Phoenix_Firestorm-Release_i686_4.2.1.29803/install.sh' Enter the desired installation directory [/opt/firestorm-install]: /home/parent - Backing up previous installation to /home/parent.backup-2012-08-27 - Installing to /home/parent cp: cannot stat `/home/parent/Downloads/Phoenix_Firestorm-Release_i686_4.2.1.29803/*': No such file or directory Failed parent@ubuntu:~$ Now whenever I go into my files it says it can't find anything. Like Cannot find home/parent/Downloads. Now, I KNOW there are downloads. I don't know why it's doing this all of a sudden. I'm so frustrated that I'm ready to just go back to Windows. I've already had to uninstall/reinstall Ubuntu once today. It's looking like I"m going to have to do it again. How can I fix my file problem that I'm now having and can someone please, please tell me how to install Firestorm? I mean they don't even have their repository listed. It's ridiculous to have to go through this over a program. Spotify wasn't hard at all to install so why is this? Someone please help, and I'm sorry if I sound like a total idiot. I'm pretty tech savvy but I'm honestly pretty upset after struggling with this for hours. Edit Okay, I see the problem with the directory files (showing the error I mentioned above when I try to click on them). I can only access my downloads, desktop, ect, through the backup that was created when I tried to install Firestorm. It's like that's the real home now. How can I get it back to the way it was? Edit Ubuntu has stopped working for me on reboot now. It doesn't go past the login screen. This is exactly what happened when I had to uninstall it before after trying to install Firestorm. Maybe I'm giving up too easily but I think I'm just going to go back to Windows. If this is what's going to happen every time I innocently try to install a program then it's just not worth it. I installed it specifically to run Firestorm because Windows sucks up a lot of CPU and causes lag. I still appreciate any input but this is just too much hassle for something that shouldn't be hard.

  Read the article

• How to use DoDirect/Paypal Pro in asp.net?

  - by ptahiliani

  using System;using System.Collections.Generic;using System.Linq;using System.Web;using System.Web.UI;using System.Web.UI.WebControls;using System.Net;using System.IO;using System.Collections;public partial class Default2 : System.Web.UI.Page{    protected void Page_Load(object sender, EventArgs e)    {    }    protected void Button1_Click(object sender, EventArgs e)    {        //API Credentials (3-token)        string strUsername = "<<enter your sandbox username here>>";        string strPassword = "<<enter your sandbox password here>>";        string strSignature = "<<enter your signature here>>";        string strCredentials = "USER=" + strUsername + "&PWD=" + strPassword + "&SIGNATURE=" + strSignature;        string strNVPSandboxServer = "https://api-3t.sandbox.paypal.com/nvp";        string strAPIVersion = "2.3";        string strNVP = strCredentials + "&METHOD=DoDirectPayment" +        "&CREDITCARDTYPE=" + "Visa" +        "&ACCT=" + "4710496235600346" +        "&EXPDATE=" + "10" + "2017" +        "&CVV2=" + "123" +        "&AMT=" + "12.34" +        "&FIRSTNAME=" + "Demo" +        "&LASTNAME=" + "User" +        "&IPADDRESS=192.168.2.236" +        "&STREET=" + "Lorem-1" +        "&CITY=" + "Lipsum-1" +        "&STATE=" + "Lorem" +        "&COUNTRY=" + "INDIA" +        "&ZIP=" + "302004" +        "&COUNTRYCODE=IN" +        "&PAYMENTACTION=Sale" +        "&VERSION=" + strAPIVersion;        try        {            //Create web request and web response objects, make sure you using the correct server (sandbox/live)            HttpWebRequest wrWebRequest = (HttpWebRequest)WebRequest.Create(strNVPSandboxServer);            wrWebRequest.Method = "POST";            StreamWriter requestWriter = new StreamWriter(wrWebRequest.GetRequestStream());            requestWriter.Write(strNVP);            requestWriter.Close();            // Get the response.            HttpWebResponse hwrWebResponse = (HttpWebResponse)wrWebRequest.GetResponse();            StreamReader responseReader = new StreamReader(wrWebRequest.GetResponse().GetResponseStream());            //and read the response            string responseData = responseReader.ReadToEnd();            responseReader.Close();            string result = Server.UrlDecode(responseData);            string[] arrResult = result.Split('&');            Hashtable htResponse = new Hashtable();            string[] responseItemArray;            foreach (string responseItem in arrResult)            {                responseItemArray = responseItem.Split('=');                htResponse.Add(responseItemArray[0], responseItemArray[1]);            }            string strAck = htResponse["ACK"].ToString();            if (strAck == "Success" || strAck == "SuccessWithWarning")            {                string strAmt = htResponse["AMT"].ToString();                string strCcy = htResponse["CURRENCYCODE"].ToString();                string strTransactionID = htResponse["TRANSACTIONID"].ToString();                //ordersDataSource.InsertParameters["TransactionID"].DefaultValue = strTransactionID;                string strSuccess = "Thank you, your order for: $" + strAmt + " " + strCcy + " has been processed.";                //successLabel.Text = strSuccess;                Response.Write(strSuccess.ToString());            }            else            {                string strErr = "Error: " + htResponse["L_LONGMESSAGE0"].ToString();                string strErrcode = "Error code: " + htResponse["L_ERRORCODE0"].ToString();                //errLabel.Text = strErr;                //errcodeLabel.Text = strErrcode;                Response.Write(strErr.ToString() + "<br/>" + strErrcode.ToString());                return;            }        }        catch (Exception ex)        {            // do something to catch the error, like write to a log file.            Response.Write("error processing");        }    }}

  Read the article

• How to Add a Taskbar to the Desktop in Ubuntu 14.04

  - by Lori Kaufman

  If you’ve switched to Ubuntu from Windows, it may take some time to get used to the new and different interface. However, you can easily incorporate a familiar Windows feature, the Taskbar, into Ubuntu to make the transition easier. A tool called Tint2 provides a bar at the bottom of the Ubuntu Desktop that resembles the Windows Taskbar. We will show you how to install it and make it start every time you log into Ubuntu. NOTE: When we say to type something in this article and there are quotes around the text, DO NOT type the quotes, unless we specify otherwise. Press Ctrl + Alt + T to open a Terminal window. To install Tint2, type the following line at the prompt and press Enter. sudo apt-get install tint2 Type your password at the prompt and press Enter. The progress of the installation displays and then a message displays saying how much disk space will be used. When asked if you want to continue, type a “y” and press Enter. When the installation has finished, close the Terminal window by typing “exit” at the prompt and pressing Enter. Click the Search button at the top of the Unity bar. Start typing “startup applications” in the Search box. Items that match what you type start displaying below the Search box. When the Startup Applications tool displays, click the icon to open it. On the Startup Applications Preferences window, click Add. On the Add Startup Program dialog box, enter a name for the startup application. This name displays in the list on the Startup Applications Preferences window. Type “tint2” in the Command edit box, enter a description in the Comment edit box, if desired, and click Add. Tint2 is added as a startup program and will start every time you log into Ubuntu. Click Close to close the Startup Applications Preferences window. Log out and log back in to make the Taskbar available on the desktop. You do not need to reboot the computer for this change to take effect. Now, when you minimize a program, an icon for it displays on the Taskbar at the bottom of the screen, just like the Taskbar in Windows. If you decide that you don’t want the Taskbar to display every time you log into Ubuntu, you can uncheck the Tint2 startup program on the Startup Applications Preferences window. You don’t need to delete it from the list.

  Read the article

• Can't fix broken packages using Synaptic (Broken Package: Wine1.4)

  - by Rustyblade

  Ok so I am trying to fix a broken package in order to install wine. When I do "sudo apt-get install wine" I get: sam@ubuntu:~$ sudo apt-get install wine [sudo] password for sam: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: wine : Depends: wine1.4 but it is not going to be installed E: Unable to correct problems, you have held broken packages. Then I try "sudo apt-get install wine1.4" sam@ubuntu:~$ sudo apt-get install wine1.4 Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: wine1.4 : Depends: wine1.4-i386 (= 1.4.1-0ubuntu1) but it is not installable Recommends: gnome-exe-thumbnailer but it is not going to be installed or kde-runtime but it is not going to be installed Recommends: winetricks but it is not going to be installed E: Unable to correct problems, you have held broken packages. So someone told me to try Synaptic. Here is what I tried: Searched wine Right clicked wine1.4 Said I needed to mark other packages Mark I click Apply. It says, You have to fix broken packages first! I do EditFix Broken Packages I get this E: Unable to correct problems, you have held broken packages. E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. E: Unable to correct dependencies E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. E: Unable to correct dependencies I am really frustrated. I removed the Official Wine PPA and tried it I even tried $ sudo apt-get -f install 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Please help me :( System: Ubuntu 12.10 64bit

  Read the article

• SSH from external network refused

  - by wulfsdad

  I've installed open-ssh-server on my home computer(running Lubuntu 12.04.1) in order to connect to it from school. This is how I've set up the sshd_config file: # Package generated configuration file # See the sshd_config(5) manpage for details # What ports, IPs and protocols we listen for #Port 22 Port 2222 # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key HostKey /etc/ssh/ssh_host_ecdsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH #LogLevel INFO LogLevel VERBOSE # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords #PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net Banner /etc/sshbanner.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM yes #specify which accounts can use SSH AllowUsers onlyme I've also configured my router's port forwarding table to include: LAN Ports: 2222-2222 Protocol: TCP LAN IP Address: "IP Address" displayed by viewing "connection information" from right-click menu of system tray Remote Ports[optional]: n/a Remote IP Address[optional]: n/a I've tried various other configurations as well, using primary and secondary dns, and also with specifying remote ports 2222-2222. I've also tried with TCP/UDP (actually two rules because my router requires separate rules for each protocol). With any router port forwarding configuration, I am able to log in with ssh -p 2222 -v localhost But, when I try to log in from school using ssh -p 2222 onlyme@IP_ADDRESS I get a "No route to host" message. Same thing when I use the "Broadcast Address" or "Default Route/Primary DNS". When I use the "subnet mask", ssh just hangs. However, when I use the "secondary DNS" I recieve a "Connection refused" message. :^( Someone please help me figure out how to make this work.

  Read the article

• Screen brightness dull after upgrade to Ubuntu 14.04

  - by user288426

  After upgrading to Ubuntu 14.04 I found that I could not increase screen brightness. I'm using a Samsung NC110 netbook. Initially the function key to modify brightness did not respond at all. After implementation of the first part of the fix, the key came alive and the brightness bar could be modified. Yet at maximum brightness indicated the screen still remained very dull. The 2nd part of the fix cures that problem, at least for this type of machine. First part of the fix was copied and modified in line with my experience from following post: How to control Brightness Open a terminal (Ctrl + Alt + T). Then type sudo nano /etc/default/grub. It will ask for your password. Type it in. Around the 11th line, there will be something like: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash". Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=Linux acpi_backlight=vendor" Save the file by Ctrl+O followed by Ctrl+X. Then run sudo update-grub in the terminal. Reboot and see if backlight adjustment works. Then I needed to modify the rc.local file. Therefore read below fix to understand the procedure: problem with adjusting brightness Ubuntu 14.04 In my case I had 2 folders listed under /sys/class/backlight which were: intel_backlight samsung I realized that the samsung folder is governing. I had to modify the check for max brightness to: cat /sys/class/backlight/samsung/max_brightness In my case the max value obtained is 8. Besides putting this into rc.local, I also had to uncomment the first line to get this working. My rc.local under /etc/ now looks as follows: !/bin/sh -e # # rc.local # # This script is executed at the end of each multiuser runlevel. # Make sure that the script will "exit 0" on success or any other # value on error. # # In order to enable or disable this script just change the execution # bits. # # By default this script does nothing. echo 8 > /sys/class/backlight/samsung/brightness exit 0 Now I can modify brightness on my netbook and also can get the screen up to its maximum brightness. Hope this is helpful.

  Read the article

• Wireless connection by using command screen

  - by Amadeus

  I installed Ubuntu 12.04 armhf to my beagleboard-xm and now trying to connect to a wireless network. First, I checked if I can search for available networks: ubuntu@arm:~$ iwlist scan lo Interface doesn't support scanning. usb0 Interface doesn't support scanning. wlan0 Scan completed : Cell 01 - Address: EA:7D:EF:60:C9:0B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=70/70 Signal level=-23 dBm Encryption key:on ESSID:"ghostrider" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Ad-Hoc Extra:tsf=000000005a1ab50e Extra: Last beacon: 6242ms ago IE: Unknown: 000A67686F73747269646572 IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 06020000 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: Unknown: 32040C121860 IE: Unknown: 2D1A2C181BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D16010800000000FF000000000000000000000000000000 IE: Unknown: DD09001018020000000000 Then I edited /etc/network/interfaces file to the following: root@arm:/etc/wpa_supplicant# cat /etc/network/interfaces auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # Example to keep MAC address between reboots #hwaddress ether DE:AD:BE:EF:CA:FE # WiFi Example auto wlan0 iface wlan0 inet dhcp wpa-ssid "ghostrider" wpa-psk "b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf" But I cannot still connect to the wireless network: root@arm:/etc/wpa_supplicant# iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Asociated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on eth0 no wireless extensions. root@arm:/etc/network# ifup wlan0 Failed to bring up wlan0. What is wrong? Should I change any other files also? But I think it was enough. By the way if you are curious about where that wpa-psk came from: zero@ghostrider:~$ wpa_passphrase ghostrider 34bddf67c2 network={ ssid="ghostrider" #psk="34bddf67c2" psk=b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf } I will appreciate any effort to help. Regards, Amadeus ps: Also I tried to connect manually: root@arm:/etc/network# iwconfig wlan0 essid ghostrider key s:34bddf67c2 But this did not solve my problem also.

  Read the article

• Software Architecture Analysis Method (SAAM)

  Software Architecture Analysis Method (SAAM) is a methodology used to determine how specific application quality attributes were achieved and how possible changes in the future will affect quality attributes based on hypothetical cases studies. Common quality attributes that can be utilized by this methodology include modifiability, robustness, portability, and extensibility. Quality Attribute: Application Modifiability The Modifiability quality attribute refers to how easy it changing the system in the future will be. This to me is a very open-ended attribute because a business could decide to transform a Point of Sale (POS) system in to a Lead Tracking system overnight. (Yes, this did actually happen to me) In order for SAAM to be properly applied for checking this attribute specific hypothetical case studies need to be created and review for the modifiability attribute due to the fact that various scenarios would return various results based on the amount of changes. In the case of the POS change out a payment gateway or adding an additional payment would have scored very high in comparison to changing the system over to a lead management system. I personally would evaluate this quality attribute based on the S.O.I.L.D Principles of software design. I have found from my experience the use of S.O.I.L.D in software design allows for the adoption of changes within a system. Quality Attribute: Application Robustness The Robustness quality attribute refers to how an application handles the unexpected. The unexpected can be defined but is not limited to anything not anticipated in the originating design of the system. For example: Bad Data, Limited to no network connectivity, invalid permissions, or any unexpected application exceptions. I would personally evaluate this quality attribute based on how the system handled the exceptions. Robustness Considerations Did the system stop or did it handle the unexpected error? Did the system log the unexpected error for future debugging? What message did the user receive about the error? Quality Attribute: Application Portability The Portability quality attribute refers to the ease of porting an application to run in a new operating system or device. For example, It is much easier to alter an ASP.net website to be accessible by a PC, Mac, IPhone, Android Phone, Mini PC, or Table in comparison to desktop application written in VB.net because a lot more work would be involved to get the desktop app to the point where it would be viable to port the application over to the various environments and devices. I would personally evaluate this quality attribute based on each new environment for which the hypothetical case study identifies. I would pay particular attention to the following items. Portability Considerations Hardware Dependencies Operating System Dependencies Data Source Dependencies Network Dependencies and Availabilities  Quality Attribute: Application Extensibility The Extensibility quality attribute refers to the ease of adding new features to an existing application without impacting existing functionality. I would personally evaluate this quality attribute based on each new environment for the following Extensibility  Considerations Hard coded Variables versus Configurable variables Application Documentation (External Documents and Codebase Documentation.) The use of Solid Design Principles

  Read the article

• Wifi problems after upgrading to 13.10

  - by Simon

  I just upgraded to Ubuntu 13.10, but since the upgrade I don't have internet access via wifi anymore. I can: See networks Connect to a network Ping myself (localhost, 192.168.0.103) I can't: Ping others (including other devices on the same wireless network, including the gateway/router) Resolve hosts Access any other external resource, whether on my own network or on the internet Using Wireshark, I noticed my computer is continuously sending ARP-requests like "Who has 192.168.0.1 [which is the gateway]? Tell 192.168.0.103". It doesn't get any replies though. When I ping another IP-address for which it knows the mac-address (from cache), it turns out a packet loss of 90% occurs, and even if a packet manages to arrive it takes around 3000ms. The output of route -n is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 9 0 0 eth1 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Before upgrading, wifi worked fine. Using other devices, wifi still works fine.Resetting the router didn't help. Ethernet still works after upgrading. Any suggestions? Update: I'm using the wl driver. Here's the relevant output of some commands: lspci | grep Wireless 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) cat /etc/modprobe.d/blacklist.conf [...] blacklist mac80211 blacklist brcm80211 blacklist cfg80211 blacklist lib80211_crypt_tkip blacklist lib80211 blacklist b43 cat /etc/rc.local sudo modprobe -r lib80211 sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_wep.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_tkip.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_ccmp.ko sudo modprobe wl exit 0 The last lines are probably how I got wireless working after the previous upgrade (wireless has been a problem after each upgrade). Update 2: added information about the exact hardware below. The hardware is an integrated device, so I ran lspci -nn | grep -i network. The output is: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01)

  Read the article

• How to use multiple search keys?

  - by user32565

  I have a database wherein the files are named abcd100.00b, abcd101.00b, etc. I need a code where when the user enters abcd separate then 100 to 110, all the files with the name abcd and in the range 100 to 110 should get displayed now the following code can display only the first four characters. How do I implement this? <?php //capture search term and remove spaces at its both ends if the is any $searchTerm = trim($_GET['keyname']) ; //check whether the name parsed is empty if($searchTerm == "rinex_file") { echo "Enter name you are searching for."; exit(); } if($searchTerm == "rinex_file") { echo "Enter name you are searching for."; exit(); } //database connection info $host = "localhost"; //server $db = "rinex"; //database name $user = "m"; //dabases user name $pwd = "c"; //password //connecting to server and creating link to database $link = mysqli_connect($host, $user, $pwd, $db); //MYSQL search statement $query = "SELECT * FROM rinexo WHERE rinex_file LIKE '%$searchTerm%'"; $results = mysqli_query($link, $query) ; /* check whethere there were matching records in the table by counting the number of results returned */ if(mysqli_num_rows($results) >= 1){ echo '<table border="1"> <tr> <th>rinex version</th> <th>program</th> <th>date</th> <th>maker name</th> <th>maker number</th> <th>observer</th> <th>agency</th> <th>position_X_Y_Z</th> </tr>'; while($row = mysqli_fetch_array($results)){ echo '<tr> <td>'.$row['rinex_version'].'</td> <td>'.$row['pgm'].'</td> <td>'.$row['date'].'</td> <td>'.$row['marker_name'].'</td> <td>'.$row['marker_no'].'</td> <td>'.$row['observer'].'</td> <td>'.$row['agency'].'</td> <td>'.$row['position_X_Y_Z'].'</td> </tr>'; } echo '</table>'; }else{ echo "There was no matching record for the name " . $searchTerm; }

  Read the article

• Notes - Part I - Say Hello from Java

  - by Silviu Turuga

  Sometimes we need to take small notes to remember things, one way to do this is to use stick notes and have them all around our desktop. But what happening if you have a lot of notes and a small office? You'll need a piece of software that will sort things for you and also it will provide you a quick way to retrieve the notes when need. Did I mention that this will keep your desktop clean and also will reduce paper waste? During the next days we'll gonna create an application that will let you manage your notes, put them in different categories etc. I'll show you step by step what do you need to do and finally you'll have the application run on multiple systems, such as Mac, Windows, Linux, etc. The only pre-requisition for this lesson is to have JDK 7 with JavaFX installed and an IDE, preferably NetBeans. I'll call this application Notes…. Part I - Say Hello from Java  From NetBeans go to Files->New Project Chose JavaFX->JavaFX FXML Application Project Name: Notes FXML name: NotesUI Check Create Application Class and name it Main After this the project is created and you'll see the following structure As a best practice I advice you to have your code in your own package instead of the default one. right click on Source Packages and chose New->Java Package name it something like this: com.turuga.notes and click Next after the package is created, select all the 3 files from step #3 and drag them over the new package chose Refactor, as this will make sure all the references are correctly moved inside the new package now you should have the following structure if you'll try to run the project you'll get an error: Unable to find class: Main right click on project name Notes and click properties go to Run and you'll see Application Class set to Main, but because we have defined our own packages, this location has been change, so click on Browse and the correct one appear: com.turuga.notes.Main last modification before running the project is to right click on NotesUI.fxml and chose Edit (if you'll double click it will open in JavaFX Scene Builder) look around line 9 and change fx:controller="NotesUIController" to fx:controller="com.turuga.notes.NotesUIController" now you are ready to run it and you should see the following On the next lesson we'll continue to play with NetBeans and start working on the interface of our project

  Read the article

• What OpenGL version(s) to learn and/or use?

  - by zuko

  So, I'm new to OpenGL... I have general knowledge of game programming but little practical experience. I've been looking into various articles and books and trying to dive into OpenGL, but I've found the various versions and old vs new way of doing things confusing. I guess my first questions is does anyone know some figures about percentages of gamers that can run each version of OpenGL. What's the market share like? 2.x, 3.x, 4.x... I looked into the requirements for Half Life 2 since I know Valve updated it with OpenGL to run on Mac and I know they usually try to hit a very wide user-base, and they say a minimum of GeForce 8 Series. I looked at the 8800 GT on Nvidia's website and it listed support for OpenGL 2.1. Which, maybe I'm wrong, sounds ancient to me since there's already 4.x. I looked up a driver for 8800GT and it says it supports 4.2! A bit of a discrepancy there, lol. I've also read things like XP only supports up to a certain version, or OS X only supports 3.2, or all kinds of other things. Overall, I'm just confused as to how much support there is for various versions and what version to learn/use. I'm also looking for learning resources. My search results thus far have pointed me to the OpenGL SuperBible. The 4th edition has great reviews on Amazon, but it teaches 2.1. The 5th edition teaches 3.3 and there are a couple things in the reviews that mention the 4th edition is better and that the 5th edition doesn't properly teach the new features or something? Basically, even within learning material I'm seeing discrepancies and I just don't even know where to start. From what I understand, 3.x started a whole new way of doing things and I've read from various articles and reviews that you want to "stay away from deprecated features like glBegin(), glEnd()" yet a lot of books and tutorials I've seen use that method. I've seen people saying that, basically, the new way of doing stuff is more complicated yet the old way is bad . Just a side note, personally, I know I still have a lot to learn beforehand, but I'm interested in tessellation; so I guess that factors into it as well, because, as far as I understand that's only in 4.x? [just btw, my desktop supports 4.2]

  Read the article

• Cannot boot from K/Ubuntu install disk on my UEFI system

  - by user93241

  I just got a new system and have been trying to get it set up w/ Win7 & Kubuntu dual-boot, but I've got a major problem. The BIOS of my motherboard (an Asus Crosshair 990FX) is strictly UEFI -- there is no legacy support mode available. I've been reading up on how to get Kubuntu installed in UEFI mode but no matter what I try I cannot seem to even boot into my install CD/USB key properly. I can get as far as the selection screen ("Try Kubuntu", "Install Kubuntu"...) but this screen starts off not appearing correctly. If I try moving the cursor around it sometimes seems to correct itself and show me my choices. But once I select "Try Kubuntu" it starts loading, the screen goes black and then proceeds to flicker -- about once every 5-10 seconds or so. This continues indefinitely. I've tried this with both Kubuntu & Ubuntu installation media, even the AMD64+Mac Ubuntu variety that is supposed to be a lot more flexible w.r.t. UEFI. The only hint I've had that the system might have booted correctly is a little drum sound that plays when booting from the Ubuntu install disk. Well, that and the fact that when I hit my system's power button it seems to shut down correctly, even ejecting the CD at the end. This might be a video driver issue; my system has two nVidia 550's, one of which is attached to my primary monitor. (The secondary isn't hooked up yet.) I'll keep looking over similar questions but any advice would be greatly appreciated. UPDATE: I've tried booting into my 12.04 install CD twice now, each time using two different options supplied by my BIOS. One seemed to offer the ability to boot into my CD under UEFI mode -- this didn't even produce the initial boot menu. The other method offers the ability to boot into my CD NOT under UEFI mode. This DOES produce the boot menu, but after this point it seems I still cannot get to a proper video mode to see what's going on.

  Read the article

• EntityRepository not found [migrated]

  - by PachinSV

  I'm new in Doctrine, I'm following the examples in the documentation. I created my entities and everything is working fine until I created a Repository. I have an entity called User and a UserRepository. But when I try to use the User repository I get the error message: Fatal error: Class 'Doctrine\ORM\EntityRepository' not found in C:\xampp\htdocs\excap\repositories\UserRepository.php on line 10 use Doctrine\ORM\EntityRepository; /** * Description of UserRepository * * @author Mario */ class UserRepository extends EntityRepository { How can I solved this? <?php //bootstrap_doctrine.php $isDevMode = true; use Doctrine\ORM\Tools\Setup; require_once 'vendor/autoload.php'; $config = Setup::createAnnotationMetadataConfiguration(array(__DIR__.'/entities'), $isDevMode); $conn = array( 'driver' => 'pdo_mysql', 'user' => 'mydbuser', 'password' => 'mydbpassword', 'dbname' => 'mydbname' ); $entityManager = \Doctrine\ORM\EntityManager::create($conn, $config); ?> <?php //boostrap.php //Entities require_once 'entities/User.php'; require_once 'entities/Gender.php'; require_once 'entities/AccessPoint.php'; //Repositories require_once 'repositories/UserRepository.php'; if(!class_exists("Doctrine\Common\Version", FALSE)) { require_once 'bootstrap_doctrine.php'; } ?> <?php // autoload.php generated by Composer if (!class_exists('Composer\\Autoload\\ClassLoader', false)) { require __DIR__ . '/composer' . '/ClassLoader.php'; } return call_user_func(function() { $loader = new \Composer\Autoload\ClassLoader(); $composerDir = __DIR__ . '/composer'; $map = require $composerDir . '/autoload_namespaces.php'; foreach ($map as $namespace => $path) { $loader->add($namespace, $path); } $classMap = require $composerDir . '/autoload_classmap.php'; if ($classMap) { $loader->addClassMap($classMap); } $loader->register(); return $loader; }); ?>

  Read the article

• Finding "Stuff" In OUM

  - by Dave Burke

  One of the first questions people asked when they start using the Oracle Unified Method (OUM) is “how do I find X ?” Well of course no one is really looking for “X”!! but typically an OUM user might know the Task ID, or part of the Task Name, or maybe they just want to find out if there is any content within OUM that is related to a couple of keys words they have in their mind. Here are three quick tips I give people: 1. Open up one of the OUM Views, then click “Expand All”, and then use your Browser’s search function to locate a key Word. For example, Google Chrome or Internet Explorer: <CTRL> F, then type in a key Word, i.e. Architecture This is fast and easy option to use, but it only searches the current OUM page 2. Use the PDF view of OUM Open up one of the OUM Views, and then click the PDF View button located at the top of the View. Depending on your Browser’s settings, the PDF file will either open up in a new Window, or be saved to your local machine. In either case, once the PDF file is open, you can use the built in PDF search commands to search for key words across a large portion of the OUM Method Pack. This is great option for searching the entire Full Method View of OUM, including linked HTML pages, however the search will not included linked Documents, i.e. Word, Excel. 3. Use your operating systems file index to search for key words This is my favorite option, and one I use virtually every day. I happen to use Windows Search, but you could also use Google Desktop Search, of Finder on a MAC. All you need to do (on a Windows machine) is to make sure your local OUM folder structure is included in the Windows Index. Go to Control Panel, select Indexing Options, and ensure your OUM folder is included in the Index, i.e. C:/METHOD/OM40/OUM_5.6 Once your OUM folders are indexed, just open up Windows Search (or Google Desktop Search) and type in your key worlds, i.e. Unit Testing The reason I use this option the most is because the Search will take place across the entire content of the Indexed folders, included linked files. Happy searching!

  Read the article

• What is the right way to group this project into classes?

  - by sigil

  I originally asked this on SO, where it was closed and recommended that I ask it here instead. I'm trying to figure out how to group all the functions necessary for my project into classes. The goal of the project is to execute the following process: Get the user's FTP credentials (username & password). Check to make sure the credentials establish a valid connection to the FTP server. Query several Sharepoint lists and join the results of those queries to create a list of items that need to have action taken on them. Each item in the list has a folder. For each item: Zip the contents of the folder. Upload the folder to the FTP server using SFTP Update the item's Sharepoint data. Email the user an Excel report showing, e.g., Items without folder paths Items that failed to zip or upload Steps 2-5 are performed on a periodic basis; if step 2 returns an invalid connection, the user is alerted and the process returns to step 1. If at any point the user presses a certain key, the process terminates. I've defined the following set of classes, each of which is in its own .cs file: SFTP: file transfer processes DataHandler: Sharepoint data retrieval/querying/updating processes. Also makes and uploads the zip files. Exceptions: Not just one class, this is the .cs file where I have all of my exception classes. Report: Builds and sends the report. Program: The main class for running the program. I recognize that the DataHandler class is a god object, but I don't have a good idea of how to refactor it. I feel like it should be more fine-grained than just breaking it into Sharepoint, Zip, and Upload, but maybe that's it. Also, I haven't yet worked out how to combine the periodic behavior with the "wait for user input at any point in the process" part; I think that involves threads, which means other classes to manage the threads... I'm not that well-versed in design patterns, but is there one that fits this project well? If this is too big of a topic to neatly explain in an SO answer, I'll also accept a link to a good tutorial on what I'm trying to do here.

  Read the article

• How to have mulptiple search keys using one filename

  - by user107020

  I have a database wherein the files are named abcd100.00b, abcd101.00b,..... i need a code where wen the user enters abcd separate then 100 to 110 . all the files with the name abcd and in the range 100 to 110 should get displayed now the following code can display pnly the first four characters how do i implement this?????? <?php //capture search term and remove spaces at its both ends if the is any $searchTerm = trim($_GET['keyname']) ; //check whether the name parsed is empty if($searchTerm == "rinex_file") { echo "Enter name you are searching for."; exit(); } if($searchTerm == "rinex_file") { echo "Enter name you are searching for."; exit(); } //database connection info $host = "localhost"; //server $db = "rinex"; //database name $user = "m"; //dabases user name $pwd = "c"; //password //connecting to server and creating link to database $link = mysqli_connect($host, $user, $pwd, $db); //MYSQL search statement $query = "SELECT * FROM rinexo WHERE rinex_file LIKE '%$searchTerm%'"; $results = mysqli_query($link, $query) ; /* check whethere there were matching records in the table by counting the number of results returned */ if(mysqli_num_rows($results) >= 1){ echo '<table border="1"> <tr> <th>rinex version</th> <th>program</th> <th>date</th> <th>maker name</th> <th>maker number</th> <th>observer</th> <th>agency</th> <th>position_X_Y_Z</th> </tr>'; while($row = mysqli_fetch_array($results)){ echo '<tr> <td>'.$row['rinex_version'].'</td> <td>'.$row['pgm'].'</td> <td>'.$row['date'].'</td> <td>'.$row['marker_name'].'</td> <td>'.$row['marker_no'].'</td> <td>'.$row['observer'].'</td> <td>'.$row['agency'].'</td> <td>'.$row['position_X_Y_Z'].'</td> </tr>'; } echo '</table>'; }else{ echo "There was no matching record for the name " . $searchTerm; }

  Read the article

• Java SE 7 Update 4??????·???????G1 GC??????“WebLogic+WebSocket”??????????????????????WebLogic Server 12c Forum 2012?????

  - by ???02

  2012?4?????????Java SE 7 Update 4????????·??????(GC)????G1 GC??????????GC???????????? ???????Web??????????????????HTML5??????/???????????????????WebSocket??????????????????WebLogic Server?????????????????????????????? 2012?8????????WebLogic Server 12c Forum 2012???????????·?????????????????????????(???) Java SE 7 Update 4??????G1 GC???????? 2012?8????????WebLogic Server 12c Forum 2012??????????????????·???????????????????????Java EE 6??????????????????????????????????????WebLogic Server????????????????????·???????????????????Java SE 7 Update 4???????GC??HTML5??????1????WebSocket??????????·????????????????????? ?????? Fusion Middleware?????? ?????????????? ???? 2012?4???????Java SE 7 Update 4?????Mac OS X????????????????????????G1 GC?????????? Fusion Middleware?????? ???????????????????????G1 GC???????????????? ????????GC???????????????????????????????????????????????????????????????????????????????????????????·??????????????????????????·??????????GC????????????????1??GC???????????????????????????????? GC????????????????????????????GC??????????????????????GC????GC???????????????????????????????GC??????????????????????????????????????????????????????????????? ???64????????????????????JVM?????64????????????64????JVM????GB???????·????????????????????????GC????????????????GC????????????????????????????·????????????????GC?????????????????????????????????????????????????????????????????SLA????????????????????·?????????????? ????????????????????????Java SE 7 Update 4????????GC?G1 GC?? G1 GC????????????????????????????????????????????????????????????GC???????????????????????????(????????)??????????????????????????????????????????????????????????????????????????????????????????? ??????G1 GC??????????????????????????????????????????? ??G1 GC?????????????????????????????????????????????????????????????????????????????????????????GC?????????????????????64????JVM????????·???????????????????????????????????????GC??????? ???????????????????????? ????????????????????????????????????????????OutOfMemory???????????????????????????????? WebLogic Server 12c?Java SE 7??????????????G1 GC???????????WebLogic Server 11g(10.3.6)??????????????????????GC????????JVM??????????-XX:+UseG1 GC????????????????? HTML5?Web????/?????????WebSocket?????????????????? ?????? Fusion Middleware?????? ?????????? ?????? ?????? Fusion Middleware???????WebLogic Server??????·???????????????????????·?????????Near future of WebLogic / ????WebLogic???????????????Web??????????HTML5???? ????????IT????????????????????1???????·?????????????????????????????????????????????????????????????HTML5?? HTML5???????HTML????????????HTML???Web????????????????????????HTML5???????????????????????????????????????????????HTML5????????/???????????????????????????????????WebWorker?????????????????????????????Web Storage???????API??????HTML5??????????????HTML??????????? ???HTML5??????????????????????WebSocket????????Web????/?????????????????????????? WebSocket????????????????????????(???????)?HTTP????????????????WebSocket????????WebSocket????????????????????????HTTP????????????????????????Web????/??????????????????? WebSocket??????????“??????Web”???????????????????????????????????????????????????????????????1???????????????????????HTTP???????????????????????????????????Comet????HTTP???????????????????????????????WebSocket???????????????????????????????????????????????????????????????? ?????????WebSocket????????????????????????????????????????????????????? WebSocket???????????????????????????? ?????? WebSocket???????(RFC 6455) ?????(Proposed Standard)??? WebSocket API(JavaScript)??(W3C) ????(Last Call Working Draft)??????2012?6?14???? WebSocket API Java EE??(JSR-356) Review Ballot??? ???? Web???? Google Chrome 16?Mozilla Firefox 11?Internet Explorer 10(PP5)?Safari 6??? ???·????? Jetty?jWebSocket?node.js?GlassFish 3.x????? ????????????????(RFC 6455)?????????JavaScript??????????????????????Java EE????????JSR-356?????????????????????????·????????????????????????????·??????????????? ??????????Java???????????????GlassFish????????????????????(JSR-356)??????????????·???·???????????????? ?WebSocket?WebLogic Server ??????????????WebSocket??WebLogic Server???????????????????? WebSocket????HTML5?????????????????????????????????HTML5?????????????????????Java EE?????????HTML5????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ???????HTML5?????????????????????????????????? ????????????? ?????????????????????????????????????????????????????????????????????????????????????????????????????HTML5???????????Java EE??????????????????????????(???) ???????????????????????????????????????????????????????????????????????????????????Java EE?WebLogic?????????????????????????????????????????????????????

  Read the article

• ????·???????! ?WebLogic Scripting Tool????WebLogic Server???/???????|WebLogic Channel|??????

  - by ???02

  Web???????????/?????????????????????????????????????????????? ??????????????????????????????????????????????????????????????????????????????WebLogic Server?????????????????WebLogic Scripting Tool??????????2011?11????????Oracle DAB & Developers Days 2011?????????????????????????!WebLogic Scripting Tool?????WLS???·????????????WebLogic Scripting Tool?????????????????(???)?WebLogic Server???/????????WebLogic Scripting Tool　WebLogic Scripting Tool(WLST)??????????????WebLogic Server???????????????????????????????????????????????????????????????????????????WLST???????????????????????????????????????????????????????????????????????????WebLogic Server?????????????????????　WLST??Java?Python?????Jython?????????????WebLogic Server?MBean?????????????????????MBean???"????(Managed)Bean"??????WebLogic Server??????????????Java??????????????JDBC????·???????????MBean??JMS(Java Message Service)????????MBean????????MBean???????????MBean???????????????????????????????WLST????UNIX??????????cd???ls?????????????????????????????MBean???　MBean??????MBean?????????????MBean??2?????????????????????MBean?????????????????????????????????????????????????????????????????????????MBean?????·?????????????????????????????????????　???WebLogic Server?MBean??????(MBean???)????????????????????MBean?????????????????MBean?????????????????????MBean????????????????????????????????????????MBean???????　????????MBean?????????????????????????????????????MBean????????????????WLST?????????　WebLogic Server?????????MBean?WLST??????????????Java???????????????????????????????????????????????????????????????????·??????????WLST???????????????????????????????????????????????????????????????????/????????????　WLST????????????????????????2??????????????????????????????????[????????]java weblogic.WLST[???????????]java weblogic.WLST XXXX.py　?????????i??????????????????????????????????????????[????????????????]java weblogic.WLST -i XXX.py　???WLST???????????????·???????????·????????????????????·????????????????????????MBean??????????MBean???????????MBean??????????????????????·????????????????????????????????????????????????????????????????????????????????????????????·?????????　???????????????????WebLogic Server???????????????????????????????????????????????WebLogic Server???????????????????WLST ???????????????????????WLST????????????????????????????????????Java????????????Python??????????????????　???????????????????????????cmo???????????????????MBean???????????????????????????????????WLST??????????serverRuntime()??????????????????????MBean??????????????cmo????????????????????????MBean???API???????????????????????????????　??1?????????????????????????????????????????????????????????????????????????????????????????????????????????????WLST????????????????????????????????????????MBean????　??????WLST????????????????MBean?????????????????????? ?????????????????????????????????????????????MBean???????????????WLST?MBean?????????????????????????MBean?????????????????????????????????　???MBean?????????????????????????????????????????Java????????????????????????????????????????????????·?????????????????????????????????????????MBean??????????????????　?????????MBean?????????????????MBean????????????????????????????Java???????????JVM Runtime MBean???Heap Free Current????????????????????????????Read Only??????????long????????????????　?????MBean?????????????????RuntimeMBean??????????????????JVMRuntimeMBean??????RuntimeMBean???????????????MBean?????????????????????????MBean?????????WLST??????????????????????????????Java???????????[???????????????]wls:/mydomain/serverConfig> serverRuntime()???????serverRuntime???????????????ServerRuntimeMBean???????????????????[find() ????? MBean ?????????]wls:/mydomain/serverRuntime> find('JVMRuntime')Finding 'JVMRuntime' in all registered MBean instances .../ JVMRuntimecom.bea:ServerRuntime=AdminServer,Name=AdminServer,Type=JVMRuntime ?[getPath() ???????????????]wls:/mydomain/serverRuntime> getPath('com.bea:ServerRuntime=AdminServer,Name=AdminServer,Type=JVMRuntime')'JVMRuntime/AdminServer'[cd() ???????????]wls:/mydomain/serverRuntime> cd('JVMRuntime/AdminServer')wls:/mydomain/serverRuntime/JVMRuntime/AdminServer>[get() ????? ls() ????? MBean ?????? ]wls:/mydomain/serverRuntime/JVMRuntime/AdminServer> get('HeapFreeCurrent')152358560Lwls:/mydomain/serverRuntime/JVMRuntime/AdminServer> ls()-r-- HeapFreeCurrent 152358560-r-- HeapFreePercent 79-r-- HeapSizeCurrent 259588096-r-- HeapSizeMax 518979584-r-- Type JVMRuntime...　??????????????????????????????from java.lang.Thread import *connect('username','password','t3://localhost:7001')serverRuntime()cd('JVMRuntime/AdminServer')print('---- HeapFreeCurrent ---')while(1):　　 print(get('HeapFreeCurrent'))　　 Thread.sleep(60000)　??????????3?????????????????????MBean????????????????????????While???Heap Free Current??????????Java?????sleep??????????????????????????WLST?2?????　????????????·?????????WLST?2????????????　1????????????????????????????????????????????????????????????WLST???????????????????????????????????????????WebLogic Server?????????????????????????????????????????????????????????????????????　???2???????????????????????????????????????????????????????????????????????????????　????????????????????????HTTP???????????????????????????????????????????????????????????????????????????????????????????????????????????HTTP???????????????????????????????????????????????????????????　????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????WLST????????????????　???2??????????·?????????????????PDF????????????????????????????????????????????Oracle Technology Network:?????????????! WebLogic Scripting Tool?????WLS???·?????···????·????????????????????

  Read the article

< Previous Page | 676 677 678 679 680 681 682 683 684 685 686 687  | Next Page >