Search Results

Search found 22358 results on 895 pages for 'django raw query'.

Page 682/895 | < Previous Page | 678 679 680 681 682 683 684 685 686 687 688 689  | Next Page >

• Linux RAID-0 performance doesn't scale up over 1 GB/s

  - by wazoox

  I have trouble getting the max throughput out of my setup. The hardware is as follow : dual Quad-Core AMD Opteron(tm) Processor 2376 16 GB DDR2 ECC RAM dual Adaptec 52245 RAID controllers 48 1 TB SATA drives set up as 2 RAID-6 arrays (256KB stripe) + spares. Software : Plain vanilla 2.6.32.25 kernel, compiled for AMD-64, optimized for NUMA; Debian Lenny userland. benchmarks run : disktest, bonnie++, dd, etc. All give the same results. No discrepancy here. io scheduler used : noop. Yeah, no trick here. Up until now I basically assumed that striping (RAID 0) several physical devices should augment performance roughly linearly. However this is not the case here : each RAID array achieves about 780 MB/s write, sustained, and 1 GB/s read, sustained. writing to both RAID arrays simultaneously with two different processes gives 750 + 750 MB/s, and reading from both gives 1 + 1 GB/s. however when I stripe both arrays together, using either mdadm or lvm, the performance is about 850 MB/s writing and 1.4 GB/s reading. at least 30% less than expected! running two parallel writer or reader processes against the striped arrays doesn't enhance the figures, in fact it degrades performance even further. So what's happening here? Basically I ruled out bus or memory contention, because when I run dd on both drives simultaneously, aggregate write speed actually reach 1.5 GB/s and reading speed tops 2 GB/s. So it's not the PCIe bus. I suppose it's not the RAM. It's not the filesystem, because I get exactly the same numbers benchmarking against the raw device or using XFS. And I also get exactly the same performance using either LVM striping and md striping. What's wrong? What's preventing a process from going up to the max possible throughput? Is Linux striping defective? What other tests could I run?

  Read the article

• Gigabyte GA-970A-UD3 mobo won't boot from USB flash drive

  - by user38586

  I am trying to boot BAMT a Debian flavor via USB on a brand new Gigabyte GA-970A-UD3 motherboard. I tried various flash drive and various OS. I never had this problem with ASUS and MSI. The problem is from Gigabyte hardware. I found that my BIOS is very strict about MBR compatibility. Now I can boot in DOS mode. The flash drive need to be formated as a Win98 Startup disk using HP USB disk storage format tool. Unetbootin menu is booting from USB but won't install BAMT. If I use Windows or Linux diskimager the working MBR is deleted. I tried converting BAMT .img to .iso and it is not booting with Unetbootin. Is it possible to boot BAMT(Debian Linux) from a Win98 DOS command prompt? Maybe there is a way to burn the image and keep the working MBR? If the working MBR is deleted, the flash drive is not recognized at all by the BIOS. This is the info I found that got me booting for the first time in DOS: GB's BIOS will only boot USBs formatted to FAT-32, conforming to normal MBR bootloader. I've seen this before, and surmised that the 'stick-maker' was formatting in ReiserFile, or one of the EXT 'flavors', but no one ever followed up to confirm or deny... Also, if it's putting the bootloader into its own partition - won't work! In the BIOS, on the "Integrated Peripherals" page, the "USB Storage Function" item must be enabled (which should be the default) to allow USB booting... I've put a little work into a 'GB USB booting tutorial', and frankly, I'd just go ahead and finish it up for you, but I really don't want to reboot the several times it will take me to 'firm up' procedural details, and take the BIOS/boot pictures for the post - just noticed VAIL finally went 'public beta', so will be downloading for likely twenty-six hours or so There's likely enough there to test a 'raw DOS boot', just to see if your hardware (especially the USB stick itself) will do it... Some post later: Fixed. Here is a brief summary. Since my ubuntu live usb sticks (2gb kingston and 8gb sandisk sd/usb reader - fat32, created in ubuntu 10.04) would not boot this board even though they would boot my ga-ep45-ud3p, I decided to try bilbat's suggestion with the HP usb boot program. I created the win98 boot disk on the kingston 2gb stick without reformatting. It booted right up. Next, I used windows version of unetbootin to write the ubuntu live cd to the kingston disk. This fired right up and completed the install. Everything seems to be in good order now. Unfortunately I can boot in DOS mode but can't boot BAMT.

  Read the article

• Restore single users Exchange 2003 mailbox from backup

  - by Campo

  I take weekly backups of exchange in full. I also take complete weekly backups of the entire server. It is a Server 2003 R2 with AD and Exchange 2003 all on one box. One users inbox has disappeared. She has 19000+ junk items now. It is possible the inbox got mixed into the junk. Regardless it is such a huge mess she is not going to go through all of that.... I want to restore he mailbox from the backup. I followed this MS KB http://support.microsoft.com/kb/823176 I had to use Method 3. I have a VM of Server 2003 R2 with exchange but I am having failures on the restore from NT backup. The backup log just states to check the application log.... Application log points to backup log... Only info Is failed to restore Only thing different is the computer name... The only error I can find is in the Application log. Information Store Database not found All others just say that the backup failed. Any assistance is greatly appreciated. UPDATE I have successfully proven I can restore the DB into a recovery storage group in my VM Unfortunately due to the actual account being on a different store I am unable to do the recovery... Error is The attempt to log on to the Microsoft Exchange Server computer has failed. The MAPI provider failed. Microsoft Exchange Server Information Store ID no: 8004011d-0512-00000000 Two questions QUESTION 1 Should I repeat my steps on the production exchange server in the recover storage group? then merge into her original account? I am just concerned with doing recovery like that on the live server.... QUESTION 2 Is there any way I can extract her .PST from my recovery VM and then import into her outlook? On the Recovery VM: I restored the raw DB from my full backup repaired it with ESEUTIL then mounted in the recovery store. Was thinking I could just repeat and mount in the main store on the VM? Thanks for the suggestions.

  Read the article

• Retrieving saved checkboxes' name and values from database

  - by sermed

  I have a form with checkboxes, each one has a value. When the registered user select any checkbox the value is incremented (the summation) and then then registred user save his selection of checkbox if he satisfied with the result of summation into database all this work fine ...i want to enable the registred user to view his selection history by retriving and displaying the checkboxes he selected in a page with thier values ... How I can do that? I'm just able to save the selected checkboxes as choice 1, choice 2, for example .. I want to view the selected checkboxes that is saved in database as the appear in the page when the user first select them: for example if the registred user selects these 3 options LEAD DEEP KEEL (1825) FULLY BATTENED MAINSAIL (558) TEAK SIDE DECKS (2889) They will be saved as for example (choice1, choice2, choice3). But if he want to view selected checkboxes the appear exactly as first he selects them: LEAD DEEP KEEL (1825) FULLY BATTENED MAINSAIL (558) TEAK SIDE DECKS (2889) This is my user table: $query="CREATE TABLE User( user_id varchar(20), password varchar(40), user_type varchar(20), firstname varchar(30), lastname varchar(30), street varchar(50), city varchar(50), county varchar(50), post_code varchar(10), country varchar(50), gender varchar(6), dob varchar(15), tel_no varchar(50), vals varchar(50), email varchar(50))"; and the code to inser the options selected to database <?php include("databaseconnection.php"); $str = ''; foreach($_POST as $key => $val) if (strpos($key,'choice') !== false) $str .= $key.','; $query = "INSERT INTO User (vals) VALUES('$str')"; $result=mysql_query($query,$conn); if ($result) { (mysql_error(); } else { echo " done"; } ?> And this is my form: function checkTotal() { document.listForm.total.value = ''; var sum = 0; for (i=0;i <form name="listForm" method="post" action="insert_options.php" > <TABLE cellPadding=3 width=600 border=0> <TBODY> <TR> <TH align=left width="87%" bgColor=#b0b3b4><SPAN class=whiteText>Item</SPAN></TH> <TH align=right width="13%" bgColor=#b0b3b4><SPAN class=whiteText>Select</SPAN></TH></TR> <TR> <TD bgcolor="#9da8af"colSpan=2><SPAN class=normalText><B>General</B></SPAN></TD></TR> <TR> <TD bgcolor="#c4c8ca"><SPAN class=normalText >TEAK SIDE DECKS (2889)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="2889" type="checkbox" onchange="checkTotal()" /></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>LEAD DEEP KEEL (1825)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="1825" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>FULLY BATTENED MAINSAIL (558)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="558" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>HIGH TECH SAILS FOR CONVENTIONAL RIG (1979)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="1979" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>IN MAST REEFING WITH HIGH TECH SAILS (2539)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="2539" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>SPlNNAKER GEAR (POLE LINES DECK FITTINGS) (820)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="820" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>SPINNAKER POLE VERTICAL STOWAGE SYSTEM (214)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="214" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>GAS ROD KICKER (208)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="208" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>SIDE RAIL OPENINGS (BOTH SIDES) (392)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="392" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>SPRING CLEATS MIDSHIPS -ALUMIMIUM (148)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="148" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>ELECTRIC ANCHOR WINDLASS (1189)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="1189" type="checkbox" onchange="checkTotal()"> </TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>ANCHOR CHAIN GALVANISED (50m) (202)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="202" type="checkbox" onchange="checkTotal()"> </TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>ANCHOR CHAIN GALVANISED (50m) (1141)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="1141" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgcolor="#9da8af"colSpan=2><SPAN class=normalText><B>NAVIGATION & ELECTRONICS</B></SPAN></TD></TR> <TR> <TD bgcolor="#c4c8ca"><SPAN class=normalText >WIND VANE (STAINLESS STEEL)(41)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="41" type="checkbox" onchange="checkTotal()" /></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>RAYMARINE ST6O LOG & DEPTH (SEPARATE UNITS)(226)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="226" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgcolor="#9da8af"colSpan=2><SPAN class=normalText><B>ENGINES & ELECTRICS</B></SPAN></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>SHORE SUPPLY (220V) WITH 3 OUTLETS (EXCLUDJNG SHORE CABLE) (327)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="327" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgColor=#c4c8ca><SPAN class=normalText>3rd BATTERY(14OA/H)(196)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="196" type="checkbox" onchange="checkTotal()"></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>24 AMP BATTERY CHARGER (475)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="475" type="checkbox" onchange="checkTotal()"></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>2 BLADED FOLDING PROPELLER (UPGRADE)(299)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="299" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgcolor="#9da8af"colSpan=2><SPAN class=normalText><B>BELOW DECKS/DOMESTIC</B></SPAN></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>WARM WATER (FROM ENGINE & 220V)(749)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="749" type="checkbox" onchange="checkTotal()"></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>SHOWER IN AFT HEADS WITH PUMPOUT(446)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="446" type="checkbox" onchange="checkTotal()"></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>DECK SUCTION DISPOSAL FOR HOLDINGTANK(166)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="166" type="checkbox" onchange="checkTotal()"></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>REFRIGERATED COOLBOX (12V)(666)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="666" type="checkbox" onchange="checkTotal()"></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>LFS SAFETY PACKAGE (COCKPIT HARNESS POINTS STAINLESS STEEL JACKSTAYS)(208)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="208" type="checkbox" onchange="checkTotal()"></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>UPHOLSTERY UPGRADE IN SALOON (SUEDETYPE)(701)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="701" type="checkbox" onchange="checkTotal()"></TD></TR> <TR> <TD bgcolor="#9da8af"colSpan=2><SPAN class=normalText><B>NAVIGATION ELECTRONICS & ELECTRICS</B></SPAN></TD></TR> <TD bgColor=#c4c8ca><SPAN class=normalText>VHF RADIO AERIAL CABLED TO NAVIGATION AREA(178)</SPAN></TD> <TD align=right bgColor=#c4c8ca><input name="choice" value="178" type="checkbox" onchange="checkTotal()"></TD></TR> </table>

  Read the article

• Setting up nginx as proxy to apache; All good, but nginx doesn't serve media

  - by becomingGuru

  I have set it up such that nginx proxies request and sends django requests to apache and serves media itself. Following documents my setup: Nginx Configuration: /etc/nginx/nginx.conf user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; access_log /var/log/nginx/access.log; sendfile on; tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; include /etc/nginx/sites-enabled/*; } ===== ngnix proxy /etc/nginx/proxy.conf ============ proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; =========== Nginx server file: /etc/nginx/sites-enabled/some-name.txt ========== server { listen 208.109.252.110:80; server_name netconf; autoindex on; access_log /home/site/server_logs/nginx_access.log; error_log /home/site/server_logs/nginx_error.log; location / { proxy_pass http://127.0.0.1:80/; include /etc/nginx/proxy.conf; } location /site_media/ { root /home/site/folder/static; } } ========== Nginx very well proxies the request and passes to apache, the required requests, but doesn't serve the media. In the last server file, location site_media is not served, at all. :( Everything seems perfect to me. What is wrong? Thanks in advance.

  Read the article

• Vagrant-aws not provisioning

  - by SuperCabbage

  I'm trying to spin up and provision an EC2 instance with Vagrant, it successfully creates the instance up and I can then use vagrant ssh to SSH into the it but Puppet doesn't seem to carry out any provisioning. Upon running vagrant up --provider=aws --provision I get the following output Bringing machine 'default' up with 'aws' provider... WARNING: Nokogiri was built against LibXML version 2.8.0, but has dynamically loaded 2.9.1 [default] Warning! The AWS provider doesn't support any of the Vagrant high-level network configurations (`config.vm.network`). They will be silently ignored. [default] Launching an instance with the following settings... [default] -- Type: m1.small [default] -- AMI: ami-a73264ce [default] -- Region: us-east-1 [default] -- Keypair: banderton [default] -- Block Device Mapping: [] [default] -- Terminate On Shutdown: false [default] Waiting for SSH to become available... [default] Machine is booted and ready for use! [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/ => /vagrant [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/manifests/ => /tmp/vagrant-puppet/manifests [default] Rsyncing folder: /Users/benanderton/development/projects/my-project/aws/modules/ => /tmp/vagrant-puppet/modules-0 [default] Running provisioner: puppet... An error occurred while executing multiple actions in parallel. Any errors that occurred are shown below. An error occurred while executing the action on the 'default' machine. Please handle this error then try again: No error message I can then SSH into the instance by using vagrant ssh but none of my provisioning has taken place, so I'm assuming that errors have occured but I'm not being given any useful information relating to them. My Vagrantfile is as following; Vagrant.configure("2") do |config| config.vm.box = "ubuntu_aws" config.vm.box_url = "https://github.com/mitchellh/vagrant-aws/raw/master/dummy.box" config.vm.provider :aws do |aws, override| aws.access_key_id = "REDACTED" aws.secret_access_key = "REDACTED" aws.keypair_name = "banderton" override.ssh.private_key_path = "~/.ssh/banderton.pem" override.ssh.username = "ubuntu" aws.ami = "ami-a73264ce" end config.vm.provision :puppet do |puppet| puppet.manifests_path = "manifests" puppet.module_path = "modules" puppet.options = ['--verbose'] end end My Puppet manifest is as following; package { [ 'build-essential', 'vim', 'curl', 'git-core', 'nano', 'freetds-bin' ]: ensure => 'installed', } None of the packages are installed.

  Read the article

• iptables blocking ssh communication

  - by Michal Sapsa

  I'm using this script for iptables: #!/bin/sh echo "1" > /proc/sys/net/ipv4/ip_forward iptables -F iptables -X iptables -F -t nat iptables -X -t nat iptables -F -t filter iptables -X -t filter iptables -t filter -P FORWARD DROP iptables -t filter -A FORWARD -s 192.168.0.0/255.255.0.0 -d 0/0 -j ACCEPT iptables -t filter -A FORWARD -s 0/0 -d 192.168.0.0/255.255.0.0 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.8.0.1/255.255.255.0 -j MASQUERADE iptables -A FORWARD -s 10.8.0.1/255.255.255.0 -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.0.0/24 -d 0/0 -j MASQUERADE iptables -I FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu iptables -t nat -A PREROUTING -i eth1 -p udp --dport 16161 -j DNAT --to 192.168.0.251:16161 iptables -t nat -A PREROUTING -i eth1 -p udp --sport 16161 -j DNAT --to 192.168.0.251:16161 #openvpn iptables -I INPUT -p tcp --dport 1194 -j ACCEPT iptables -I INPUT -p udp --dport 1194 -j ACCEPT I end up with some iptables rules that should work but don't work - probably because of me. # Generated by iptables-save v1.4.12 on Mon May 26 13:15:43 2014 *raw :PREROUTING ACCEPT [1657523:1357257330] :OUTPUT ACCEPT [36804:34834370] -A PREROUTING -p icmp -j TRACE -A PREROUTING -p tcp -j TRACE -A OUTPUT -p icmp -j TRACE -A OUTPUT -p tcp -j TRACE COMMIT # Completed on Mon May 26 13:15:43 2014 # Generated by iptables-save v1.4.12 on Mon May 26 13:15:43 2014 *nat :PREROUTING ACCEPT [5033:345623] :INPUT ACCEPT [154:34662] :OUTPUT ACCEPT [6:1968] :POSTROUTING ACCEPT [2:120] -A PREROUTING -i eth0 -p tcp -m tcp --dport 16161 -j DNAT --to-destination 192.168.0.251:22 -A PREROUTING -i eth1 -p tcp -m tcp --dport 16161 -j DNAT --to-destination 192.168.0.251:22 -A POSTROUTING -s 10.8.0.0/24 -j MASQUERADE -A POSTROUTING -s 192.168.0.0/24 -j MASQUERADE COMMIT # Completed on Mon May 26 13:15:44 2014 # Generated by iptables-save v1.4.12 on Mon May 26 13:15:44 2014 *filter :INPUT ACCEPT [548:69692] :FORWARD DROP [8:384] :OUTPUT ACCEPT [2120:1097479] -A INPUT -p udp -m udp --dport 1194 -j ACCEPT -A INPUT -p tcp -m tcp --dport 1194 -j ACCEPT -A FORWARD -p tcp -m tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu -A FORWARD -s 192.168.0.0/16 -j ACCEPT -A FORWARD -d 192.168.0.0/16 -j ACCEPT -A FORWARD -s 10.8.0.0/24 -j ACCEPT -A FORWARD -i eth0 -o eth1 -p tcp -m tcp --dport 22 -j ACCEPT -A FORWARD -i eth1 -o eth0 -p tcp -m tcp --dport 22 -j ACCEPT COMMIT TRACE at PREROUTEING AND OUTPUT are only for debuging this thing. When I ssh at public ip with port 16161 I don't get any message, only TimeOut so it looks like I don't get communication back to remote server. ETH0 is the world, ETH1 is LAN Any IPTABLES Masters willing to give a hand ? iptables -vL Chain INPUT (policy ACCEPT 20548 packets, 3198K bytes) pkts bytes target prot opt in out source destination 38822 7014K ACCEPT udp -- any any anywhere anywhere udp dpt:openvpn 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:openvpn Chain FORWARD (policy DROP 1129 packets, 64390 bytes) pkts bytes target prot opt in out source destination 214K 11M TCPMSS tcp -- any any anywhere anywhere tcpflags: SYN,RST/SYN TCPMSS clamp to PMTU 4565K 1090M ACCEPT all -- any any 192.168.0.0/16 anywhere 5916K 7315M ACCEPT all -- any any anywhere 192.168.0.0/16 0 0 ACCEPT all -- any any 10.8.0.0/24 anywhere 0 0 ACCEPT tcp -- any any anywhere 192.168.0.251 tcp dpt:16161 Chain OUTPUT (policy ACCEPT 59462 packets, 19M bytes) pkts bytes target prot opt in out source destination

  Read the article

• Revolutionary brand powder packing machine price from affecting marketplace boom and put on uniform in addition to a lengthy service life

  - by user74606

  In mining in stone crushing, our machinery company's encounter becomes much more apparent. As a consequence of production capacity in between 600~800t/h of mining stone crusher, stone is mine Mobile Cone Crushing Plant Price 25~40 times, effectively solved the initially mining stone crusher operation because of low yield prices, no upkeep problems. Full chunk of mining stone crusher. Maximum particle size for crushing 1000x1200mm, an effective answer for the original side is mine stone provide, storing significant chunks of stone can not use complications in mines. Completed goods granularity is modest, only 2~15mm, an effective option for the original mine stone size, generally blocking chute production was an issue even the grinding machine. Two types of material mixed great uniformity, desulfurization of mining stone by adding weight considerably. Present quantity added is often reached 60%, effectively minimizing the cost of raw supplies. Electrical energy consumption has fallen. Dropped 1~2KWh/t tons of mining stone electrical energy consumption, annual electricity savings of one hundred,000 yuan. Efficient labor intensity of workers and also the atmosphere. Due to mine stone powder packing machine price a high degree of automation, with out human make contact with supplies, workers working circumstances enhanced significantly. Positive aspects, and along with mine for stone crushing, CS series cone Crusher has the following efficiency traits. CS series cone Crusher Chamber is divided into 3 unique designs, the user is usually chosen in accordance with the scenario on site crushing efficiency is high, uniform item size, grain shape, rolling mortar wall friction and put on uniform in addition to a extended service life of crushing cavity-. CS series cone Crusher utilizes a one of a kind dust-proof seal, sealing dependable, properly extend the service life of the lubricant replacement cycle and parts. CS series Sprial Sand washer price manufacture of important components to choose unique materials. Each and every stroke left rolling mortar wall of broken cone distances, by permitting a lot more products into the crushing cavity, as well as the formation of big discharge volume, speed of supplies by way of the crushing Chamber. This machine makes use of the principle of crushing cavity, also as unique laminated crushing, particle fragmentation, so that the completed product drastically improved the proportions of a cube, needle-shaped stones to lower particle levels extra evenly.

  Read the article

• Netcat file transfer problem

  - by thepurplepixel

  I have two custom scripts I just wrote to facilitate transferring files between my VPS and my home server. They are both written in bash (short & sweet): To send: #!/bin/bash SENDFILE=$1 PORT=$2 HOST='<my house>' HOSTIP=`host $HOST | grep "has address" | cut --delimiter=" " -f 4` echo Transferring file \"$SENDFILE\" to $HOST \($HOSTIP\). tar -c "$SENDFILE" | pv -c -N tar -i 0.5 | lzma -z -c -6 | pv -c -N lzma -i 0.5 | nc -q 1 $HOSTIP $PORT echo Done. To receive: #!/bin/bash SERVER='<myserver>' SERVERIP=`host $SERVER | grep "has address" | cut --delimiter=" " -f 4` PORT=$1 echo Receiving file from $SERVER \($SERVERIP\) on port $PORT. nc -l $PORT | pv -c -N netcat -i 0.5 | lzma -d -c | pv -c -N lzma -i 0.5 | tar -xf - echo Done. The problem is that, for a very quick second, I see something flash along the lines of "Connection Refused" (before pv overwrites it), and no file is ever transferred. The port is forwarded through my router, and nmap confirms it: ~$ sudo nmap -sU -PN -p55515 -v <my house> Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-21 18:10 EDT NSE: Loaded 0 scripts for scanning. Initiating Parallel DNS resolution of 1 host. at 18:10 Completed Parallel DNS resolution of 1 host. at 18:10, 0.00s elapsed Initiating UDP Scan at 18:10 Scanning 74.13.25.94 [1 port] Completed UDP Scan at 18:10, 2.02s elapsed (1 total ports) Host 74.13.25.94 is up. Interesting ports on 74.13.25.94: PORT STATE SERVICE 55515/udp open|filtered unknown Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 2.08 seconds Raw packets sent: 2 (56B) | Rcvd: 5 (260B) Also, running netcat normally doesn't work either: squircle@summit:~$ netcat <my house> 55515 <my house> [<my IP>] 55515 (?) : Connection refused Both boxes are Ubuntu Karmic (9.10). The receiver has no firewall, and outbound traffic on that port is allowed on the sender. I have no idea what to troubleshoot next. Any ideas? P.S.: Feel free to move this to SO/SF if you feel it would fit better there.

  Read the article

• iptables management tools for large scale environment

  - by womble

  The environment I'm operating in is a large-scale web hosting operation (several hundred servers under management, almost-all-public addressing, etc -- so anything that talks about managing ADSL links is unlikely to work well), and we're looking for something that will be comfortable managing both the core ruleset (around 12,000 entries in iptables at current count) plus the host-based rulesets we manage for customers. Our core router ruleset changes a few times a day, and the host-based rulesets would change maybe 50 times a month (across all the servers, so maybe one change per five servers per month). We're currently using filtergen (which is balls in general, and super-balls at our scale of operation), and I've used shorewall in the past at other jobs (which would be preferable to filtergen, but I figure there's got to be something out there that's better than that). The "musts" we've come up with for any replacement system are: Must generate a ruleset fairly quickly (a filtergen run on our ruleset takes 15-20 minutes; this is just insane) -- this is related to the next point: Must generate an iptables-restore style file and load that in one hit, not call iptables for every rule insert Must not take down the firewall for an extended period while the ruleset reloads (again, this is a consequence of the above point) Must support IPv6 (we aren't deploying anything new that isn't IPv6 compatible) Must be DFSG-free Must use plain-text configuration files (as we run everything through revision control, and using standard Unix text-manipulation tools are our SOP) Must support both RedHat and Debian (packaged preferred, but at the very least mustn't be overtly hostile to either distro's standards) Must support the ability to run arbitrary iptables commands to support features that aren't part of the system's "native language" Anything that doesn't meet all these criteria will not be considered. The following are our "nice to haves": Should support config file "fragments" (that is, you can drop a pile of files in a directory and say to the firewall "include everything in this directory in the ruleset"; we use configuration management extensively and would like to use this feature to provide service-specific rules automatically) Should support raw tables Should allow you to specify particular ICMP in both incoming packets and REJECT rules Should gracefully support hostnames that resolve to more than one IP address (we've been caught by this one a few times with filtergen; it's a rather royal pain in the butt) The more optional/weird iptables features that the tool supports (either natively or via existing or easily-writable plugins) the better. We use strange features of iptables now and then, and the more of those that "just work", the better for everyone.

  Read the article

• Apache server completely freezes until it gets restarted

  - by nbv4

  My server does this every few days. What sucks is that it always seems to do this right after I go to bed, so when I wake up, I'm greeted with the fact that my server has been down for the past 6 or 7 hours. When I first noticed this, I added a cronjob that tries to restart the server every 15 minutes, but I guess that didn't fix it. Once I noticed the server was down, I can this command: /etc/init.d/apache2 restart * Restarting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName ... waiting ...........................................................apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName httpd (pid 17597) already running ...which is odd, because a restart should restart the server, even if it's already running, correct? I eventually had to "stop" then "start" to get it working again. I then looked through the logs, and found something very weird. It seems that around the time the server crashed, the logs have entries that are wildly out of order. It looks a little like this: xx.xxx.xxx.x - - [21/Apr/2010:06:32:05 -0400] "GET / blah" xx.xxx.xxx.x - - [21/Apr/2010:06:51:25 -0400] "GET / blah" x.xx.xxx.xxx - - [21/Apr/2010:06:38:23 -0400] "GET / blah" xxx.xx.xx.xx - - [21/Apr/2010:06:31:56 -0400] "GET / blah" xxx.xx.xx.xx - - [21/Apr/2010:06:51:49 -0400] "GET / blah" xx.xx.xxx.xx - - [21/Apr/2010:06:33:20 -0400] "GET / blah" I don't think the problem is memory, because this: tells me that right before the crash, memory usage is fine. I'm running apache with the worker mpm, here are the settings for that: <IfModule mpm_worker_module> StartServers 1 MaxClients 100 MinSpareThreads 5 MaxSpareThreads 10 ThreadsPerChild 10 MaxRequestsPerChild 3000 </IfModule> This apache server is running a bunch of stuff, but most of the traffic comes from a django project I'm hosting, that uses mod_wsgi. There also is a simple machines forum that is running off of mod_fcgid. Those setting are below: <IfModule mod_fcgid.c> MaxRequestsPerProcess 500 MaxProcessCount 3 AddHandler fcgid-script .php .fcgi AddHandler cgi-script .cgi .pl FCGIWrapper "/usr/bin/php-cgi" .php </IfModule> Anyone know of anything else I can check? I've just about tweaked every single setting I can think of, yet these freezes still happen.

  Read the article

• What are incentives (if any) to use WinRT instead of .Net?

  - by Ark-kun

  Let's compare WinRT with .Net .Net .Net is the 13+ years evolution of COM. Three main parts of .Net are execution environment, standard libraries and supported languages. CLR is the native-code execution environment based on COM .Net Framework has a big set of standard libraries (implemented using managed and native code) that can be used from all .Net languages. There are .Net classes that allow using OS APIs. WPF or Silverlight provide a XAML-based UI framework .Net can be used with C++, C#, Javascript, Python, Ruby, VB, LISP, Scheme and many other languages. C++/.Net is a variation of the C++ language that allows interaction with .Net objects. .Net supports inheritance, generics, operator and method overloading and many other features. .Net allows creating apps that run on Windows (XP, 7, 8 Pro (Desktop and Metro), RT, CE, etc), Mac OS, Linux (+ other *nix); iOS, Android, Windows Phone (7, 8); Internet Explorer, Chrome, Firefox; XBox 360, Playstation Suite; raw microprocessors. There is support for creating games (2D/3D) using any managed language or C++. Created by Developer Division WinRT WinRT is based on COM. Three main parts of WinRT are execution environment, standard libraries and supported languages. WinRT has a native-code execution environment based on COM WinRT has a set of standard libraries that more or less can be used from WinRT languages. There are WinRT classes that allow using OS APIs. Unnamed Silverlight clone provides a XAML-based UI framework WinRT can be used with C++, C#, Javascript, VB. C++/CX is a variation of the C++ language that allows interaction with WinRT objects. Custom WinRT components don't support inheritance (classes must be sealed), generics, operator overloading and many other features. WinRT allows creating apps that run on Windows 8 Pro and RT (Metro only); Windows Phone 8 (limited). There is support for creating games (2D/3D) using C++ only. Ordered by Windows Team I think that all the aspects except the last ones are very important for developers. On the other hand it seems that the most important aspect for Microsoft is the last one. So, given the above comparison of conceptually identical technologies, what are incentives (if any) to use WinRT instead of .Net?

  Read the article

• Varnish server in front of nginx server with multiple virtualhosts

  - by Garreth 00

  I have tried to search for a solution for this, but can't find any documentation/tips on my specific setup. My setup: Backendserver: ngnix: 2 different websites (2 top domains) in virtualenv, running gunicorn/python/django Backendserver hardware(VPS) 2gb ram, 8 CPU Databaseserver: postgresql - pg_bouncer Backendserver hardware (VPS) 1gb ram, 8 CPU Varnishserver: only running varnish Varnishserver hardware (VPS) 1gb ram, 8 CPU I'm trying to set up a varnish server to handle rare spike in traffic (20 000 unique req/s) The spike happens when a tv program mention one of the sites. What do I need to do, to make the varnish server cache both sites/domains on my backendserver? My /etc/varnish/default.vcl : backend django_backend { .host = "local.backendserver.com"; .port = "8080"; } My /usr/local/nginx/site-avaible/domain1.com upstream gunicorn_domain1 { server unix:/home/<USER>/.virtualenvs/<DOMAIN1>/<APP1>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain1.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80 default_server; listen 8080; client_max_body_size 4G; server_name www.domain1.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain1; break; } } } My /usr/local/nginx/site-avaible/domain2.com upstream gunicorn_domain2 { server unix:/home/<USER>/.virtualenvs/<DOMAIN2>/<APP2>/run/gunicorn.sock fail_timeout=0; } server { listen 80; listen 8080; server_name domain2.com; rewrite ^ http://www.domains.com$request_uri? permanent; } server { listen 80; listen 8080; client_max_body_size 4G; server_name www.domain2.com; keepalive_timeout 5; # path for static files root /home/<USER>/<APP>-media/; location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; if (!-f $request_filename) { proxy_pass http://gunicorn_domain2; break; } } } Right now, If I try the Ip of the varnishserver I only get served domain1.com. Would everything be correct if I change the DNS of the two domain to point to the varnishserver, or is there extra setup before it would work? Question 2: Do I need a dedicated server for varnish, or could I just install varnish on my backendserver, or would the server run out of memory quick?

  Read the article

• Any way to recover ext4 filesystems from a deleted LVM logical volume?

  - by Vegar Nilsen

  The other day I had a proper brain fart moment while expanding a disk on a Linux guest under Vmware. I stretched the Vmware disk file to the desired size and then I did what I usually do on Linux guests without LVM: I deleted the LVM partition and recreated it, starting in the same spot as the old one, but extended to the new size of the disk. (Which will be followed by fsck and resize2fs.) And then I realized that LVM doesn't behave the same way as ext2/3/4 on raw partitions... After restoring the Linux guest from the most recent backup (taken only five hours earlier, luckily) I'm now curious on how I could have recovered from the following scenario. It's after all virtually guaranteed that I'll be a dumb ass in the future as well. Virtual Linux guest with one disk, partitioned into one /boot (primary) partition (/dev/sda1) of 256MB, and the rest in a logical, extended partition (/dev/sda5). /dev/sda5 is then setup as a physical volume with pvcreate, and one volume group (vgroup00) created on top of it with the usual vgcreate command. vgroup00 is then split into two logical volumes root and swap, which are used for / and swap, logically. / is an ext4 file system. Since I had backups of the broken guest I was able to recreate the volume group with vgcfgrestore from the backup LVM setup found under /etc/lvm/backup, with the same UUID for the physical volume and all that. After running this I had two logical volumes with the same size as earlier, with 4GB free space where I had stretched the disk. However, when I tried to run "fsck /dev/mapper/vgroup00-root" it complained about a broken superblock. I tried to locate backup superblocks by running "mke2fs -n /dev/mapper/vgroup00-root" but none of those worked either. Then I tried to run TestDisk but when I asked it to find superblocks it only gave an error about not being able to open the file system due to a broken file system. So, with the default allocation policy for LVM2 in Ubuntu Server 10.04 64-bit, is it possible that the logical volumes are allocated from the end of the volume group? That would definitely explain why the restored logical volumes didn't contain the expected data. Could I have recovered by recreating /dev/sda5 with exactly the same size and disk position as earlier? Are there any other tools I could have used to find and recover the file system? (And clearly, the question is not whether or not I should have done this in a different way from the start, I know that. This is a question about what to do when shit has already hit the fan.)

  Read the article

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• Set up Gmail with Google apps for own domain

  - by erdomester

  I rent a server from a German company. I have remote access to it as well as WHM and CPanel. I decided to use Google's mail servers for obvious reasons. I am not an admin just an average guy trying to set up what needs to be set up. The problem is I am unable to make the necessary settings. I watched Youtube tutorials, followed written ones as well as Google's help, but there is (at least) one serious problem with my domain settings. The domain console alwasy says Your MX records are incorrect When I check dappwall.com in mxtoolbox.com it says Pref Hostname IP Address TTL 10 mail.dappwall.com 46.4.88.247 24 hrs But this is not the host name. I checked WHM and my hostname is server1.dappwall.com. I can confirm it by typing the hostname command in putty. However, if I do an mx lookup at mxtoolbox.com on server1.dappwall.com or mail.dappwall.com I get Lookup failed after 1 name servers timed out or responded non-authoritatively I ran checks on the google apps toolbox on dappwall.com and two problems emerged: 1.No Google mail exchangers found. Relayhost configuration? 10 mail.dappwall.com In Google Apps > Settings for Gmail > Advanced settings it also says that my current MX records for dappwall.com is Priority Points to 10 MAIL.DAPPWALL.COM. So mail.dappwall.com again. I also have access to a robot provided by the company I rent the server from. Here I see this mail at two places but how should I (if it's necessary) modify this? I set Email routing to Automatically Detect Configuration. 2.There SHOULD be a valid SPF record. "v=spf1 include:_spf.google.com ~all" In the DNS Zone Editor I added this spf record: Name TTL Class Type Record dappwall.com. 1440 IN TXT v=spf1 include:_spf.google.com ~all In the cPanel Email Authentication page it says SPF: Status: Enabled Warning: cPanel is unable to verify that this server is an authoritative nameserver for dappwall.com. [?] Your current raw SPF record is : v=spf1 include:_spf.google.com ~all How can I confirm that my server is an authoritative nameserver for dappwall.com? In WHM Service Configuration Mailserver selection Dovecot was set but I disabled it (i don't know if that's ok). What am I missing here? Where is that mail.dappwall.com coming from?

  Read the article

• Recover strategy single bad sector in moricon

  - by Damon

  This week, my harddisk made me an early christmas present in the form of a single defect sector. To make up for the puny size of the present, it chose a sector inside moricons.dll for that. This means that now the system takes about 5 minutes to boot before Windows gives up and moves on, and there's 2 dozen scary "critical failure" entries in the system log after every boot, which is annoying. OK, admittedly, I shouldn't complain, it could be worse, the bad sector could be in ntldr... SMART info more or less indicates (for what SMART can indicate anyway) that the drive is mostly OK. Soft Read Error Rate has a score of 96, and Current Pending Sector Count has a raw value of 8, which translates to a score of 100. Acronis DriveMonitor makes this an issue (lowering the overall rating to 75%), HDD Health calls it "excellent", giving an overall rating of 95% (which is what this harddisk from day one). No single score is below 95 (power on hours and spin up count), and most are 100 anyway. Well, whatever, I've seen drives with perfect SMART values fail from one second to the other, and drives with moderate values work for years. So, I'm inclined not to put too much weight into that overall. TL;DR Now... to the problem: I don't feel like trashing the disk just yet (that's planned with a new OS install upgrading to Win7 early next year, independently of this issue), but in the mean time, I would still like to have a smoothly running system again. Therefore, I feel tempted to tamper with it, but before I render my system entirely unusable (since I've never done this before), I'd like to verify that my planned procedere is likely to suceed in having a working system again: Copy moricons.dl_ from the Windows install disk, rename it to moricons.zip, and unzip it. This gives an intact 5.1.2600.2180 version (the broken one is 5.1.2600.5512 - but I guess this makes not much of a difference, since it's an icon-only DLL, and an outdated copy should work better than one that can't be read) Run chkdsk /r /f` which will "repair" the file (i.e. delete the file without asking, tell the drive to remap the sector, and toss some unreadable junk into a file with a hexadecimal number) Hopefully Windows still boots after this (is that a reasonable expectation, or do I need to have something like BartPE ready? -- but then again, what's that good for in case chkdsk has nuked the entire file system...) Delete the junk file generated by chkdsk, copy the new DLL to %windir%\system32 Reboot. Pray. Maybe I just shouldn't touch anything, since it still kind of works... if annoying, but it works. Unsure... But, is there anything fundamentally wrong with the planned approach? Is this a sensible approach at all?

  Read the article

• How to run a restricted set of programs with Administrator privileges without giving up Admin acces (Win7 Pro)

  - by frLich

  I have a shared system, running Windows7 X64, restricted to a 'standard user' with no password. Not everyone who has access to the system has the administrator password. This works rather well, except for some applications - specially the unlock-applications for encrypted hard drives/USB flash drives. The specific ones either require Administrator access (eg. Seagate Blackarmor) or simply fail without it -- since these programs are sending raw commands to a device, this is to be expected. I would like to be able to add the hashes of these particular programs to a whitelist, and have them run as administrator without needing any prompts. Since these are by definition on removable media, I can't simply use a filename or even a path. One of the users who shares the system can be considered 'crafty', so anything which temporarily grants administrator rights to an user account is certain to cause problems. What i'd like to be able to do: 1) Create an admin account that can only run programs from a whitelist (or, failing that, from a directory) I can't find a good way to do this: As far as I can tell, SRP applies equally to ALL users? Even if I put a "Deny" token on all directories on the system, such that new directories would inherit it, it could still potentially run things from the mounted USB devices. I also don't know whether it's possible to create a new directory that DOESN'T inherit from the parent, that would lake the deny token, and provide admin access. 2) Find a lightweight service that will run these programs in its local context Windows7 seems to block cross-privilege level communication by default, and I haven't found such for windows 7. One example seems to be "sudo" (http://pages.cpsc.ucalgary.ca/~nfriess/sudo/) but because it uses a WLNOTIFY hook, it won't work under Vista nor Windows7 Non-Solutions: - RunAs: Requires administrator password! (but everyone calls it "sudo" anyway) - RunAs /savecred: Nice idea, but appears to be completely insecure. - RUNASSPC - Same concept as RunAs, uses "encrypted" files with credentials, but checks in user-space. - Scheduled Tasks - "Fixed" permissions make this difficult, and doesn't support interactive processes even if it did. - SuRun: From Google: "Surun uses its own Windows service that adds the user to the group of administrators during program start and removes him automatically from that group again"

  Read the article

• Tips for maximizing Nginx requests/sec?

  - by linkedlinked

  I'm building an analytics package, and project requirements state that I need to support 1 billion hits per day. Yep, "billion". In other words, no less than 12,000 hits per second sustained, and preferably some room to burst. I know I'll need multiple servers for this, but I'm trying to get maximum performance out of each node before "throwing more hardware at it". Right now, I have the hits-tracking portion completed, and well optimized. I pretty much just save the requests straight into Redis (for later processing with Hadoop). The application is Python/Django with a gunicorn for the gateway. My 2GB Ubuntu 10.04 Rackspace server (not a production machine) can serve about 1200 static files per second (benchmarked using Apache AB against a single static asset). To compare, if I swap out the static file link with my tracking link, I still get about 600 requests per second -- I think this means my tracker is well optimized, because it's only a factor of 2 slower than serving static assets. However, when I benchmark with millions of hits, I notice a few things -- No disk usage -- this is expected, because I've turned off all Nginx logs, and my custom code doesn't do anything but save the request details into Redis. Non-constant memory usage -- Presumably due to Redis' memory managing, my memory usage will gradually climb up and then drop back down, but it's never once been my bottleneck. System load hovers around 2-4, the system is still responsive during even my heaviest benchmarks, and I can still manually view http://mysite.com/tracking/pixel with little visible delay while my (other) server performs 600 requests per second. If I run a short test, say 50,000 hits (takes about 2m), I get a steady, reliable 600 requests per second. If I run a longer test (tried up to 3.5m so far), my r/s degrades to about 250. My questions -- a. Does it look like I'm maxing out this server yet? Is 1,200/s static files nginx performance comparable to what others have experienced? b. Are there common nginx tunings for such high-volume applications? I have worker threads set to 64, and gunicorn worker threads set to 8, but tweaking these values doesn't seem to help or harm me much. c. Are there any linux-level settings that could be limiting my incoming connections? d. What could cause my performance to degrade to 250r/s on long-running tests? Again, the memory is not maxing out during these tests, and HDD use is nil. Thanks in advance, all :)

  Read the article

• Serving protected files using Nginx's X-Accel-Redirect header

  - by andybak

  I'm trying to serve protected files using this directive in my nginx.conf: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/secure/; } I'm passing in paths in the form: "/myfile.doc" and the file's path would be: /home/ldr/webapps/nginx/app/secure/myfile.doc I just get 404's when I access "http: //myserver/secure/myfile.doc" (space inserted after http to stop ServerFault converting it to a link) I've tried taking the trailing / off the location directive and that makes no difference. Two questions: How do I fix it! How can I debug problems like this myself? How can I get Nginx to report which path it's looking for? error.log shows nothing and access.log just tells me which url is being requested - this is the bit I already know! It's no fun trying things randomly without any feedback. Here's my entire nginx.conf: daemon off; worker_processes 2; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server { listen 21534; server_name my.server.com; client_max_body_size 5m; location /media/ { alias /home/ldr/webapps/nginx/app/media/; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; fastcgi_pass unix:/home/ldr/webapps/nginx/app/myproject/django.sock; fastcgi_pass_header Authorization; fastcgi_hide_header X-Accel-Redirect; fastcgi_hide_header X-Sendfile; fastcgi_intercept_errors off; include fastcgi_params; } location /secure { internal; alias /home/ldr/webapps/nginx/app/secure/; } } } EDIT: I'm trying some of the suggestions here So I've tried: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/; } both with and without the trailing slash on location. I've also tried moving this block before the "location /" directive. The page I linked to has ^~ after 'location' giving: location ^~ /secure/ { ...etc... Not sure what that signifies but it didn't work either!

  Read the article

• How to run a restricted set of programs with Administrator privileges without giving up Admin acces (Win7 Pro)

  - by frLich

  I have a shared system, running Windows7 X64, restricted to a 'standard user' with no password. Not everyone who has access to the system has the administrator password. This works rather well, except for some applications - specially the unlock-applications for encrypted hard drives/USB flash drives. The specific ones either require Administrator access (eg. Seagate Blackarmor) or simply fail without it -- since these programs are sending raw commands to a device, this is to be expected. I would like to be able to add the hashes of these particular programs to a whitelist, and have them run as administrator without needing any prompts. Since these are by definition on removable media, I can't simply use a filename or even a path. One of the users who shares the system can be considered 'crafty', so anything which temporarily grants administrator rights to an user account is certain to cause problems. What i'd like to be able to do: 1) Create an admin account that can only run programs from a whitelist (or, failing that, from a directory) I can't find a good way to do this: As far as I can tell, SRP applies equally to ALL users? Even if I put a "Deny" token on all directories on the system, such that new directories would inherit it, it could still potentially run things from the mounted USB devices. I also don't know whether it's possible to create a new directory that DOESN'T inherit from the parent, that would lake the deny token, and provide admin access. 2) Find a lightweight service that will run these programs in its local context Windows7 seems to block cross-privilege level communication by default, and I haven't found such for windows 7. One example seems to be "sudo" (http://pages.cpsc.ucalgary.ca/~nfriess/sudo/) but because it uses a WLNOTIFY hook, it won't work under Vista nor Windows7 Non-Solutions: - RunAs: Requires administrator password! (but everyone calls it "sudo" anyway) - RunAs /savecred: Nice idea, but appears to be completely insecure. - RUNASSPC - Same concept as RunAs, uses "encrypted" files with credentials, but checks in user-space. - Scheduled Tasks - "Fixed" permissions make this difficult, and doesn't support interactive processes even if it did. - SuRun: From Google: "Surun uses its own Windows service that adds the user to the group of administrators during program start and removes him automatically from that group again"

  Read the article

• Network speeds being report as 4x higher than actual in Windows 7 SP1

  - by Synetech

  Ever since installing Windows 7 SP1, I have noticed that all programs that display my network transfer rate have been exactly 4x higher than they actually are. For example, when I download something from a high-bandwidth web site or through torrents with lots of sources, the download rate indicated is is ~5MBps (~40Mbps) even though my Internet connection has a maximum of only 1.5MBps (12Mbps). It is the same situation with the upstream bandwidth: the connection maximum is 64KBps, but I’m seeing up to 256KBps. I have tried several different programs for monitoring bandwidth throughput and they all give the same results. I also tried different times and different days, and they always show the rate as being four times too high. My initial thought was that my ISP had increased the speeds (without my noticing), which they have done before. However, I checked my ISP’s site and they have not increased the speeds. Moreover, when I look at the speeds in the program actually doing the transfer (eg Chrome, µTorrent, etc.), the numbers are in line with the expected values at the same time that bandwidth monitoring programs are showing the high numbers. The only significant change (and pretty much the only change at all) that has occurred to my system since the change was the installation of SP1 for Windows 7. As such, it is my belief that some sort of change exists in SP1 whereby software that accesses the bandwidth via a specific API receives (erroneously?) high numbers while others that have access to the raw data continue to receive the correct values. I booted into Windows XP and downloaded some things via HTTP and torrent and in both cases, the numbers were as expected (like they were in Windows 7 before installing SP1). I then booted back into 7SP1 and once again, the numbers were four times higher than possible. Therefore it is definitely something in SP1 that has changed how local bandwidth is calculated/returned. There is definitely something wonky with Windows 7 SP1’s network speed calculation. I tried Googling this, but (for multiple reasons), have had a difficult time finding anything relevant. Has anybody else noticed this behavior? Does anybody know of any bugs or changes in SP1 that could account for it?

  Read the article

• TrueCrypt partition will no longer mount

  - by sparkyuiop

  I am hoping for some advice to help me out of my situation, with luck. I have a computer running Windows 7 Ultimate x64 with 3 hard disks installed. On my 2TB hard disk 2 (non-system disk) I have 4 partitions. One is for music, another for video, a downloads partition and a 500GB RAW Truecrypt encrypted partition / volume that I had setup to mount with 4 photographs used as keyfiles. The 4 photographs are located in my 'Documents' partition which is one of four partitions on my 1.5TB hard disk 1 (non-system disk) When I setup the disk encryption I did not (I'm 99% sure) create a password, I only used the 4 photograph keyfiles to mount the volume. Recently my 1TB hard disk 0 (system / boot) started to fail so I decided to replace it. I was going to clone the old disk to a new disk but decided that a fresh installation would be more beneficial. Once I had transferred all the required 'User Data' from my old hard disk 0 (C: disk) I discarded it. I reinstalled Truecrypt, pointed to the partition, selected my 4 keyfiles photographs and I mounted my encrypted volume with no issues. In fact I mounted it several times after re-installing Windows and after reboots. Now all of a sudden when I try and mount it I get the message "incorrect keyfile(s) and/or password or not a Truecrypt volume". Now I am not sure why this happened as I do not recall exactly what I did between last mounting the volume successfully and it not mounting. Here are some of the possible things I may have done to cause it to stop working but I am at a loss as to where to start to try and resolve the problem. 1. I had swapped the drive letters to a preferred order. 2. I possibly swapped the physical SATA connectors on the mainboard. 3. I enabled 'Hot Plugging' for the two non-system hard disk SATA ports and the DVD SATA port in the BIOS. I have tried changing the encrypted partition drive letter as suggested in another post but this does not help. On my old system the encrypted drive was drive "X". I have about tried it with all the other free drive letters but alas nothing changes. I do not recall what drive letter was allocated to the encrypted partition before I changed them all. I have not tried to change the letter back to what it possibly was to start with as I am happy with the current layout. I will try this is anyone thinks it would be worthwhile though. I do hope I have managed to convey my situation in an understandable manner and live in hope someone could help me recover years of personal files. Thank you very much for taking the time to read my post and for any suggestions you may offer. Regards Phillip Thorne (UK) Anyone???

  Read the article

• I have a very long and repetitive python path, where do I look to correct this?

  - by ninja123

  I know it is probably not necessary to paste the whole path, but just for the record I have done so below. Whenever I run a python command, it takes a long time to load this path I suppose. I have checked in .bash_profile and only have these two lines: export PATH=/Users/username/bin:/opt/local/Library/Frameworks/Python.framework/Versions/2.5/bin:/opt/local/bin:/opt/local/sbin:/opt/local/apache2/bin:$PATH export PYTHONPATH=/opt/local/lib/python2.5/site-packages/ And my python path as outputed by Django's debug is: Python path : ['/Users/username/Sites/videocluster/eggs/ipython-0.10-py2.5.egg', '/Users/username/Sites/videocluster/eggs/South-0.6.1-py2.5.egg', '/Users/username/Sites/videocluster/eggs/django_markitup-0.5.2-py2.5.egg', '/Users/username/Sites/videocluster/eggs/DateTime-2.12.0-py2.5.egg', '/Users/username/Sites/videocluster/eggs/Markdown-2.0.3-py2.5.egg', '/Users/username/Sites/videocluster/eggs/PIL-1.1.7-py2.5-macosx-10.5-i386.egg', '/Users/username/Sites/videocluster/eggs/djangorecipe-0.20-py2.5.egg', '/Users/username/Sites/videocluster/eggs/zc.recipe.egg-1.2.3b2-py2.5.egg', '/Users/username/Sites/videocluster/eggs/zc.buildout-1.5.0b2-py2.5.egg', '/Users/username/Sites/videocluster/eggs/pytz-2010h-py2.5.egg', '/Users/username/Sites/videocluster/eggs/zope.interface-3.6.1-py2.5-macosx-10.5-i386.egg', '/Users/username/Sites/videocluster/eggs/setuptools-0.6c11-py2.5.egg', '/Users/username/Sites/videocluster/parts/django', '/Users/username/Sites/videocluster', '/Users/username/Sites/videocluster/bin', '/opt/local/lib/python2.5/site-packages/setuptools_git-0.3.3-py2.5.egg', '/opt/local/lib/python2.5/site-packages/pysqlite-2.5.5-py2.5-macosx-10.5-i386.egg', '/opt/local/lib/python2.5/site-packages/CouchDB-0.5-py2.5.egg', '/opt/local/lib/python2.5/site-packages/httplib2-0.4.0-py2.5.egg', '/opt/local/lib/python2.5/site-packages/PyYAML-3.08-py2.5-macosx-10.5-i386.egg', '/opt/local/lib/python2.5/site-packages/simple_db_migrate-1.2.8-py2.5.egg', '/opt/local/lib/python2.5/site-packages/PyDispatcher-2.0.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/pyOpenSSL-0.9-py2.5-macosx-10.5-i386.egg', '/opt/local/lib/python2.5/site-packages/greenlet-0.2-py2.5-macosx-10.5-i386.egg', '/opt/local/lib/python2.5/site-packages/Supay-0.0.2-py2.5.egg', '/opt/local/lib/python2.5/site-packages/configobj-4.6.0-py2.5.egg', '/opt/local/lib/python2.5/site-packages/Fabric-0.9b1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/fudge-0.9.3-py2.5.egg', '/opt/local/lib/python2.5/site-packages/pydelicious-0.5.3-py2.5.egg', '/opt/local/lib/python2.5/site-packages/feedparser-4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/github_cli-0.2.5.2-py2.5.egg', '/opt/local/lib/python2.5/site-packages/simplejson-2.0.9-py2.5-macosx-10.5-i386.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', ......(repeating)....... '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/harobed.paster_template.advanced_package-0.2-py2.5.egg', '/opt/local/lib/python2.5/site-packages/squash-0.5.0dev-py2.5.egg', '/opt/local/lib/python2.5/site-packages/eventlet-0.8.13-py2.5.egg', '/opt/local/lib/python2.5/site-packages/FeinCMS-1.0.2-py2.5.egg', '/opt/local/lib/python2.5/site-packages/pyenchant-1.5.3-py2.5.egg', '/opt/local/lib/python2.5/site-packages/guppy-0.1.9-py2.5-macosx-10.5-i386.egg', '/opt/local/lib/python2.5/site-packages/django_scraper-0.1dev-py2.5.egg', '/opt/local/lib/python2.5/site-packages/Pympler-0.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/fabric.contrib.packagemanager-0.1dev-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/selenium-1.0.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/Scrapy-0.9_dev-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', ......(repeating)....... '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/site-packages/zc.buildout-1.4.1-py2.5.egg', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/site-packages/setuptools-0.6c11-py2.5.egg', '/opt/local/lib/python2.5/site-packages', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python25.zip', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/plat-darwin', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/plat-mac', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/plat-mac/lib-scriptpackages', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/lib-tk', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/lib-dynload', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/site-packages/Numeric', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/site-packages/PIL', '/opt/local/lib/python2.5/site-packages/PIL', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', ......(repeating)....... '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/lib/python2.5/site-packages/gtk-2.0', '/opt/local/Library/Frameworks/Python.framework/Versions/2.5/lib/python2.5/site-packages/gtk-2.0'] Someone, please tell me where I can go to correct this. Thanks

  Read the article

• How to suppress an unwanted external Autodiscover lookup?

  - by chris

  In a small network with Exchange 2007, when starting Outlook 2010 (and once in a while afterwards), users get a prompt to confirm that it's safe to get account configuration information from cpanelemaildiscovery.cpanel.net/autodiscover/autodiscover.xml (I could read in a couple of forums that there is a bug in cpanel, but that's beside the point.) I'm puzzled because I can't find any autodiscover DNS entries anywhere, neither internally nor externally. The only hint is that we use an external hosting company for our website and for one single email address, which runs on cpanel. So I guess that Outlook makes an external DNS query to test all entries? It reates a lot of confusion for the users and frankly I'm not too happy that the external hosting company gets contacted by all our users. How can I suppress this behavior? Thanks

  Read the article

< Previous Page | 678 679 680 681 682 683 684 685 686 687 688 689  | Next Page >