Search Results

Search found 29093 results on 1164 pages for 'network interface'.

Page 69/1164 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

  • Network: Incoming connections work, outgoing fails

    - by anirvan
    i recently set up my own server at home to run Ubuntu 12.04 server ed. on booting up, i noticed that a message related to networking comes up, and the booting process pauses. the message read something like - waiting for network configuration and after a while - waiting another 60 seconds... on booting up, I realised that any command which requires a network connection was not working - ping, apt-get install, etc. on firing the ifup eth0 command, I get the error RTNETLINK answers: File exists. Failed to bring up eth0. I also realised, while searching the web for this problem, that this is probably one of the most common networking related issues - however, most of the questions are around setting up multiple IPs for the same machine. ifdown eth0 also fails, stating that eth0 is not configured. my /etc/network/interfaces file has a simple configuration for a static IP: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx gateway xx.xx.xx.xx dns-nameservers xx.xx.xx.xx The strangest part of this problem is that, while I can't connect to anything outside, I can ping to this particular server using the static IP configured in the interface file, and, i can even SSH into it! I'm really at ends here with this problem, and any guidance is much appreciated. Thanks!

    Read the article

  • How do I connect to a wireless network?

    - by Keith Groben
    I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

    Read the article

  • Lost connectivity after configuring multiple network adapters on separate networks

    - by Dave Long
    I am trying to setup an Ubuntu hosting server, currently just for development, and the server has two NICs, each sitting on a different network. eth0 is on 192.168.200.* and eth1 is on 192.168.101.* and each one has a static IP. eth0 is the public facing NIC card and eth1 is strictly for internal access to the server. I initially only setup eth0 and added the eth1 card when I needed it. eth0 was working find until I added eth1, now, can't get any connectivity on eth0 unless I pull eth1 out of the box. The configuration on each system is as follows: auto eth0 iface eth0 inet static address 192.168.200.94 netmask 255.255.255.0 network 192.168.200.0 broadcast 192.168.200.255 gateway 192.168.200.253 auto eth1 iface eth1 inet static address 192.168.101.64 netmask 255.255.255.0 network 192.168.101.0 broadcast 192.168.101.255 gateway 192.168.101.254 Again eth0 worked fine until I added eth1. I have seen this happen with Windows servers if you have a Default Gateway setup for both NICs, but I am not sure if this works the same on Ubuntu. My resolv.conf file looks like so: nameserver 192.168.101.59 nameserver 192.168.101.58 domain domain.local search domain.local Per request here is the Routing table 192.168.101.0 * 255.255.255.0 U 0 0 0 eth1 192.168.200.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.101.254 0.0.0.0 UG 100 0 0 eth1 default 192.168.200.253 0.0.0.0 UG 100 0 0 eth0

    Read the article

  • Network/browser issues after upgrade to 12.04

    - by Reg
    I let my laptop upgrade to 12.04. And have no network afterwards. I went through all the articles I could find in google. Right now, I can ping google, and yahoo, but not cnn.com for example or anything else. Firefox says it can't reach google.com or gmail.com (or anything, not even IP. /etc/network/interfaces dns-nameservers 8.8.8.8 <<<<<added auto lo iface lo inet loopback /etc/dhcp/dhclient.conf #prepend domain-name-servers 8.8.8.8,8.8.4.4; prepend domain-name-servers 127.0.0.1; <<<<< tried both /etc/NetworkManager/NetworkManager.conf with and without dns=dnsmasq commented out. I can ping my wireless router and connect to it just fine. Have tried proxy/noproxy. This looks like After Upgrade to 12.04 - cannot connect to network but no answer there. I would hate to do a fresh install. Any assistance appreciated.

    Read the article

  • Network(ing) to the Limit

    - by Oracle OpenWorld Blog Team
     By Karen Shamban While Oracle OpenWorld attendees are networking, there's an Oracle Global IT team that builds and maintains the massive networks that help run the show. The objective? To keep things running as seamlessly and smoothly as possible, constantly evaluate priorities, mitigate risk, and be ready for whatever might happen -- because things do happen when there are 50,000 plus attendees, tens of thousands of devices, unexpected requirements, and a constant flow of up-to-the-minute information. Here's just some of what it takes to keep the conference going, network style: 100 Oracle network, voice, and desktop engineers; security, risk management, and other IT experts, who come in from 17 countries  1000+ network switches 300+ miles of copper and fiber 485 wireless access points 2,500 wired laptops 300 VoIP phones And just where are all these networks and devices deployed? This is what the team had to build and manage: Moscone North, South, and West, including: The keynote hall Oracle DEMOgrounds in the Exhibition Halls Hundreds of session rooms Connection Centers, Social Avenue, Lounges Registration The Howard Street Tent and Taylor Street Cafe tented venues Oracle Square (Union Square) Yerba Buena Gardens Masonic Auditorium Sessions and demos at 8 hotel venues That's a whole lot of networking going on. And here's the kicker: the team has only 4 days to bring get it all up and running across these many venues, and exactly 12 hours to take it all down once the show ends. The Global IT team puts in the equivalent of 152 24-hour days for set-up, 227 24-hour days of support during the conferences, and then tears it all down in about 20 24-hour days. And in case you were wondering, the planning for next year's Oracle OpenWorld starts ... next week. No rest for the weary.  Now THAT's networking!  So hats off to the Global IT team -- the job ain't easy, but somebody's got to do it, and they do it remarkably well.

    Read the article

  • IPMI not fucntioning with Network Bonding

    - by muhammed sameer
    Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

    Read the article

  • VMware virtual machine network devices malfunctioning

    - by sheepz
    I'm running Ubuntu 10.04 LTS and VMvware workstation 7.0.1 build-227600. The virtual machine i'm running in VMware is a custom distribution built on Debian Linux version 3.1. I'm still pretty much a beginner with UNIX administration. After having messed around with the vmware (changed only the name of the folder, the vmx and and other .v* files accordingly in which the .vmx was situated, and the configuration in the vmx file accordingly), the network devices on the virtual machine do not work anymore. The virtual machine is used for securely sending messages. The virtual machine: As far as I know, this perl file called proxy-gen-ifalias eth0 is responsible for properly setting up the two virtual network devices eth0 and eth1. The Virtual machine comes with a GUI interface in which I have set up two ethernet network devices, one internal, the other external. Now, after having messed around with this, the UI gives me this error message: perl proxy-gen-ifalias eth0 /etc/modprobe.d/alias-eth0 /sbin/update-modules perl proxy-gen-ifalias eth1 /etc/modprobe.d/alias-eth1 /sbin/update-modules ifdown eth0 ifdown: interface eth0 not configured ifdown eth1 ifdown: interface eth1 not configured perl proxy-gen-netcfg /etc/network/interfaces ifup eth0 SICCSIFADDR: No such device eth0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device eth0: ERROR while getting interface flags: No such device Failed to bring up eth0. ifconfig eth0 eth0: error fetching interface information: Device not found make: *** [/etc/network/interfaces] Error 1 ~ Here are the contents of the two perl files referred to in the message: paste.pocoo.org/show/2AMzAYhoCRZqlGY7wUFk/ proxy-gen-netcfg

    Read the article

  • How to get ISA 2006 Web Proxy to work with the Single Network Adapter template

    - by tronda
    I need to test an issue with running our application behind a proxy server with different type of configurations, so I installed ISA 2006 Enterprise on a desktop computer. Since this computer only has a single network card and I want to start out easy, I chose the "Single Network Adapter" template. We have a internal NAT'ed network which is in the 10 range. I have defined the internal network on the ISA server to be 10.XXX.YY.1 - 10.XXX.YY.255 I also have the Default rule which denies all traffic, but I've added the following Rule: Policy - Protocols - From - To Accept HTTP Internal External HTTPS Local Host Internal HTTS Server Localhost Then I configured Internet Explorer on a virutal machine running XP within virtualbox with Brigded network (gets same network address range as regular computers on our network) similar to this Instead of the server name I used the IP address. When I try to access a web page, this doesn't go through and I get the following log messages on the proxy server: Original Client IP Client Agent Authenticated Client Service Referring Server Destination Host Name Transport HTTP Method MIME Type Object Source Source Proxy Destination Proxy Bidirectional Client Host Name Filter Information Network Interface Raw IP Header Raw Payload GMT Log Time Source Port Processing Time Bytes Sent Bytes Received Cache Information Error Information Authentication Server Log Time Client IP Destination IP Destination Port Protocol Action Rule Result Code HTTP Status Code Client Username Source Network Destination Network URL Server Name Log Record Type 10.XXX.YY.174 - TCP - - - 24.08.2010 13:25:24 1080 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.174 10.XXX.YY.175 80 HTTP Initiated Connection MyHTTPAccess 0x0 ERROR_SUCCESS Internal Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:24 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.159 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.159 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 10.XXX.YY.166 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.166 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 0.0.0.0 Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Yes Proxy 10.XXX.YY.175 TCP GET Internet - - - Req ID: 096c76ae; Compression: client=No, server=No, compress rate=0% decompress rate=0% - - - 24.08.2010 13:25:27 0 2945 2581 446 0x0 0x40 24.08.2010 06:25:27 10.XXX.YY.174 10.XXX.YY.175 80 http Failed Connection Attempt MyHTTPAccess 10061 anonymous Internal Local Host http://www.vg.no/ PROXYTEST Web Proxy Filter 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:27 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:27 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall

    Read the article

  • Oracle Social Network and the Flying Monkey Smart Target

    - by kellsey.ruppel
    Originally posted by Jake Kuramoto on The Apps Lab blog. I teased this before OpenWorld, and for those of you who didn’t make it to the show or didn’t come by the Office Hours to take the Oracle Social Network Technical Tour Noel (@noelportugal) ran, I give you the Flying Monkey Smart Target. In brief, Noel built a target, about two feet tall, which when struck, played monkey sounds and posted a comment to an Oracle Social Network Conversation, all controlled by a Raspberry Pi. He also connected a Dropcam to record the winner just prior to the strike. I’m not sure how it all works, but maybe Noel can post the technical specifics. Here’s Noel describing the Challenge, the Target and a few other tidbit in an interview with Friend of the ‘Lab, Bob Rhubart (@brhubart). The monkey target bits are 2:12-2:54 if you’re into brevity, but watch the whole thing. Here are some screen grabs from the Oracle Social Network Conversation, including the Conversation itself, where you can see all the strikes documented, the picture captured, and the annotation capabilities: #gallery-1 { margin: auto;? } #gallery-1 .gallery-item { float: left; margin-top: 10px; text-align: center; width: 33%; } #gallery-1 img { border: 2px solid #cfcfcf; } #gallery-1 .gallery-caption { margin-left: 0; }    That’s Diego in one shot, looking very focused, and Ernst in the other, who kindly annotated himself, two of the development team members. You might have seen them in the Oracle Social Network Hands-On Lab during the show. There’s a trend here. Not by accident, fun stuff like this has becoming our calling card, e.g. the Kscope 12 WebCenter Rock ‘em Sock ‘em Robots. Not only are these entertaining demonstrations, but they showcase what’s possible with RESTful APIs and get developers noodling on how easy it is to connect real objects to cloud services to fix pain points. I spoke to some great folks from the City of Atlanta about extending the concepts of the flying monkey target to physical asset monitoring. Just take an internet-connected camera with REST APIs like the Dropcam, wire it up to Oracle Social Netwok, and you can hack together a monitoring device for a datacenter or a warehouse. Sure, it’s easier said than done, but we’re a lot closer to that reality than we were even two years ago. Another noteworthy bit from Noel’s interview, beginning at 2:55, is the evolution of social developer. Speaking of, make sure to check out the Oracle Social Developer Community. Look for more on the social developer in the coming months. Noel has become quite the Raspberry Pi evangelist, and why not, it’s a great tool, a low-power Linux machine, cheap ($35!) and highly extensible, perfect for makers and students alike. He attended a meetup on Saturday before OpenWorld, and during the show, I heard him evangelizing the Pi and its capabilities to many people. There is some fantastic innovation forming in that ecosystem, much of it with Java. The OTN gang raffled off five Pis, and I expect to see lots of great stuff in the very near future. Stay tuned this week for posts on all our Challenge entrants. There’s some great innovation you won’t want to miss. Find the comments. Update: I forgot to mention that Noel used Twilio, one of his favorite services, during the show to send out Challenge updates and information to all the contestants.

    Read the article

  • WCF <operation>Async methods not generated in proxy interface

    - by Charlie
    I want to use the Asnyc methods rather than the Begin on my WCF service client proxy because I'm updating WPF controls and need to make sure they're being updated from the UI thread. I could use the Dispatcher class to queue items for the UI thread but that's not what I'm asking about.. I've configured the service reference to generate the asynchronous operations, but it only generates the methods in proxy's implementation, not it's interface. The interface only contains syncronous and Begin methods. Why aren't these methods generated in the interface and is there a way to do this, or do I have to create a derived interface to manually add them?

    Read the article

  • pfSense 2.1 OpenVPN client not using tunnelled interface

    - by Brian M. Hunt
    I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

    Read the article

  • How to monitor current output/receive queue length in Linux

    - by IZhen
    I want to check the capacity and performance of my network. Besides checking the txkB/s and rxkB/s via Sar, I'd also like to see the average queue length of the network interface(so that the average queueing time in the interface can be calculated). It seems that netstat can give a per socket queue length, is it possible to get a per interface statics(a bit like Network Interface\Output Queue Length in Windows)? A related and kind of reverse questions is How do I view the TCP Send and Receive Queue sizes on Windows? Thanks

    Read the article

  • Sonicwall with failover, multiple subnets, and preferred WAN interface per subnet

    - by Dan
    I am trying to set up my Sonicwall TZ-210 as follows: Two WAN interfaces (different ISPs), set up in failover mode. Two LAN interfaces with different subnets Each LAN subnet will have a preferred outbound WAN interface, but would failover when necessary. In this way, each ISP is being used for a separate subnet of my network, but both subnets could failover to the other ISP if their primary went down. I know how to do 1 and 2, but I don't know how to do 3. I could set up a route for each subnet to go through a specific interface, but what would happen in the event of a failover? Would it automatically update those routes? Thanks!

    Read the article

  • ifconfig return "unknown interface: no such device"

    - by xolstice
    I'm trying to install a Linux driver for my wireless network card (D-Link DWL-G510) on my Red Hat Linux 7.1 machine with a 2.4.37.9 kernel. I downloaded the serial monkey driver from the sourceforge site and was able to successfully compile the rt73 module and load it into the kernel. The problem now is that everytime I issue the command ifconfig wlan0 up it keeps returning with the following error message: wlan0: unknown interface: No such device. I'm at a loss as to what to do here. I specifed wlan0 as the alias for the rt73 module in the modules.conf and also tried to load the driver with the command modprobe rt73 ifname=wlan0 (this specifies the interface name according to the instructions packaged in the driver), but the error message still keeps coming up. Is there something else I need to do in Linux to configure the wlan0 part or is the module not recognizing the wireless network card? It would be quite strange if it is the later since all information from the Internet is indicating this is the linux driver I should be using for mentioned wireless card.

    Read the article

  • Get CLSID by PIA interface Type

    - by Charles
    How can I get the CLSID for a given interface within a Primary Interop Assembly? Here's what I'm talking about: // The c# compiler does some interesting magic. // The following code ... var app = new Microsoft.Office.Interop.Outlook.Application(); // ... is compiled like so (disassembled with Reflector): var app =((Microsoft.Office.Interop.Outlook.Application) Activator.CreateInstance(Type.GetTypeFromCLSID(new Guid("0006F03A-0000-0000-C000-000000000046")))); Microsoft.Office.Interop.Outlook.Application is an interface, and therefore it cannot be instantiated directly. What's interesting here is that c# lets you treat these COM interfaces as if there where classes that you can instantiate with the new keyword. What I want to know is, given the System.Type for a given interface, how can I get the CLSID? Note: I ultimately want to be able to create an instance given the interface's System.Type - I don't really care how. I'm assuming here that the easiest way to do this would be to get CLSID given the Type, just as the c# compiler does.

    Read the article

  • Windows Server Hyper-V guests cannot see each other on network

    - by Noldorin
    I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

    Read the article

  • Windows Server Hyper-V guests cannot see each other on network

    - by Noldorin
    I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

    Read the article

  • Static IPv4 and dynamic IPv6 on same interface

    - by Zsub
    I am trying to set up a CentOS 5.4 box to use a static IPv4 address, while getting a dynamic IPv6 address at boot time. I have only one interface, apart from the loopback interface, eth0. It has a static v4 and internet connectivity (I can SSH in). However, it doesn't get an IPv6 by default. I have enabled IPv6 in /etc/sysconfig/network and I have added IPV6INIT=yes to the config in /etc/sysconfig/networking/devices/. If I use dhcp6c it does get a valid IPv6 address, but the main question is how do I configure it to get one at boot-time?

    Read the article

  • Single-port 2600 router with 2900XL switch

    - by Slava Maslennikov
    I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

    Read the article

  • How can one setup a version control system on a local network, without a server?

    - by Andrew
    Edit: Ok so I learned that I guess I need an distributed source control, however are there any UI based ones, and do they allow you to merge with other users on the network? This is kind of a two part question, so here it goes. I want to start developing a web application at home (with multiple developers). However, I don't have a dedicated server nor want to pay for on. So first, I don't know which version control system to use for this case, as at work we mostly have TFS setup, so I am not to familiar with whats out there. What are the best free CVS/SVN tools out there? Second, is it possible to somehow setup the CVS/SVN where there is no dedicated server and both clients store up to one week of the source code from the last check-in? Also, it would be helpful if it could integrate with visual studio, again this isn't that important at all. Problem: There are Five users, one is a Server. Server Connected: All Ok Server Disconnected: No one can share. What I am looking for: No Server: Users still have versioning based on version id of last check-in. Users must check all version on network to make sure they aren't outdated based on their last version id. If not check-in, otherwise merge/get latest. If they are update checkin, and set current version id +1.

    Read the article

  • Filesystem access through web interface

    - by Jorge Suárez de Lis
    I have an SSH+Samba server so people can access its files from anywhere on the network. I thought it would be also interesting to provide access through a web interface, so they can access the files even when they don't have access to the VPN or a Samba/SSH client. Something like the Ubuntu One or Dropbox web interface. The http server could be on the same machine as the SSH+Samba, so it should just provide access to local files and some way to login with their username/password. Someone knows any software like this?

    Read the article

  • Force local IP traffic to an external interface

    - by calandoa
    I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to be able to forward all the traffic to one of these local address trhough the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 are not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

    Read the article

  • Windows XP can't connect to wireless network

    - by mikez302
    I have a desktop computer with a wireless card, running Windows XP SP3. For a little while, I had a remote network connection set up for my job, but I didn't need the remote connection so I deleted it. Now, I am unable to connect to the internet at all from that computer through my wireless router. I can connect through my router using my laptop, and I can connect through my neighbor's router using my desktop, but for some reason I can't connect through my own router using my desktop. I see the "Wireless Network Connection 5" icon in my system tray, but it tells me it is not connected. When I click on the icon, I see a list of wireless networks, including my own, which is set up to automatically connect, although it doesn't. When I try to connect to my network on my own (by clicking on it, then clicking "Connect"), it asks me for my network password like it usually does. I see a box come up saying "Waiting for network to be ready..." and it hangs there. On the list of wireless networks, my network says "Acquiring network address" but it doesn't actually connect. How can I fix this? I tried rebooting my computer, repairing my connection, and restarting my router, and I am still having this problem.

    Read the article

  • How do I disable the network connection from .Net without needing admin priveledges?

    - by Brad Mathews
    I may be SOL on this but I thought I would give throw it out for possible solutions. I am writing a computer access control service to help me control my kids' computer use. Plan on open sourcing it when I have it working. It is written in VB.Net and needs to work on XP through 7. I am running into all sorts of security and desktop access issues on Windows 7. The service needs to run as admin to execute the NetSh command to disable the network. But I cannot interact with the desktop from the service so I IPC to a UI to handle other stuff, but I still cannot detect from the service if the desktop is locked. Argghh! I could get it all working from a hidden windows form app if I could just lick the one piece that needs admin permissions: disabling the network. It does no good if a kid logs on and denies the popup asking if the program should run as administrator and he says no. Also windows 7 will not start a program set to run as admin using HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run Anyone know how to get this working? Or have an outside the box solution? Thanks! Brad

    Read the article

  • Correct way of bringing network interface down in linux

    - by Karolis T.
    For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

    Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >