Search Results

Search found 23890 results on 956 pages for 'issue'.

Page 691/956 | < Previous Page | 687 688 689 690 691 692 693 694 695 696 697 698  | Next Page >

• multiple ip for a server not reachable

  - by andrewk

  FYI: I've read everything on Serverfault related to this question and have faced a different issue. Simply put, I've got one server (apache2) with couple of sites on it. It currently has 1 ip. I'm trying to assign/add another ip to that server, so I can give each site a different ip for ssl purposes. I am not lucking out. The new ip simply is unreachable, I've pinged it. This is what I've got below, what am I doing wrong. auto lo iface lo inet loopback auto eth0 eth0:0 eth0:1 iface eth0 inet static address 70.116.5.244 netmask 255.255.255.0 gateway 70.116.5.1 #THE NEW IP iface eth0:0 inet static address 26.175.217.102 netmask 255.255.255.0 #PRIVATE IP iface eth0:1 inet static address 192.168.158.88 netmask 255.255.128.0 NOTE: THESE IP'S ARE TWEAKED BUT RELATIVE I've read many questions here 90% similar to this but most actually have the IP respond, not this case. Thanks netstar -r output Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default gw-u6.linode.co 0.0.0.0 UG 0 0 0 eth0 70.116.5.0 * 255.255.255.0 U 0 0 0 eth0 26.175.217.0 * 255.255.255.0 U 0 0 0 eth0 192.168.128.0 * 255.255.128.0 U 0 0 0 eth0

  Read the article

• Logging hurts MySQL performance - but, why?

  - by jimbo

  I'm quite surprised that I can't see an answer to this anywhere on the site already, nor in the MySQL documentation (section 5.2 seems to have logging otherwise well covered!) If I enable binlogs, I see a small performance hit (subjectively), which is to be expected with a little extra IO -- but when I enable a general query log, I see an enormous performance hit (double the time to run queries, or worse), way in excess of what I see with binlogs. Of course I'm now logging every SELECT as well as every UPDATE/INSERT, but, other daemons record their every request (Apache, Exim) without grinding to a halt. Am I just seeing the effects of being close to a performance "tipping point" when it comes to IO, or is there something fundamentally difficult about logging queries that causes this to happen? I'd love to be able to log all queries to make development easier, but I can't justify the kind of hardware it feels like we'd need to get performance back up with general query logging on. I do, of course, log slow queries, and there's negligible improvement in general usage if I disable this. (All of this is on Ubuntu 10.04 LTS, MySQLd 5.1.49, but research suggests this is a fairly universal issue)

  Read the article

• SQL Server Express backup/restore error: The Media Family on Device is Incorrectly Formed.

  - by Chris

  Basically, I'm having this issue: http://www.sqlcoffee.com/Troubleshooting047.htm What I'm doing is running a script I found online (http://pastebin.com/3n0ZfybL) to do a full backup, then rar'ing up the file and moving it to my computer. The CRC of the backup file inside the rar is correct on both computers, so there is no problem with data being corrupted when I transfer it. But then I go and try to restore the database on my dev computer here and I get the errors "sql server cannot process this media family" ... "msg 3013". Why is this happening? I'd test out the backup on the server I'm getting it from, but it's a production server. Edit: I was about to say how I wasn't doing anything stupid like trying to restore the database to an earlier version of SQL Server, but apparently I am: From: Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (Intel X86) Mar 29 2009 10:27:29 Copyright (c) 1988-2008 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6002: Service Pack 2) To: Microsoft SQL Server 2005 - 9.00.3042.00 (Intel X86) Feb 9 2007 22:47:07 Copyright (c) 1988-2005 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6001: Service Pack 1) Let me get back to this post after I reinstall this.

  Read the article

• Why are snapshots considered as temporary backups not real backups?

  - by Samselvaprabu

  I am using VMware ESXi. In our team we use to provide snapshots for long term backup. Then we faced issues like memory spillover and the server got hang up. I started reading in VMware knowledgebase articles and everywhere. Everywhere it was recommended not to have snapshots for a long time. Even VMware advised to keep snapshots for maximum of three days. But our team kept asking us to have at least two permanent snapshots (till deleting the VM). Sometimes we may use the VM for a year). one snapshot is for fresh machine state. (So when we complete testing an application, we will revert back to fresh state and install another application) (If I did not allow that, I may often need to host the VM.) Next snapshot for keeping the VM in some state (maybe they would have found an issue and keep that state for some time. Or they may install prerequisites for the application and keep the machine ready for testing.) Logically, their needs seems to be fair. But if I allow that, I am to permit them to hold the snapshots for long time. We are not using our VM as a mail server or database server. Why is keeping snapshots for long time having an adverse effect? Why are snapshots considered as temporary backups, not real backups?

  Read the article

• ssh keys rejected each day

  - by EddyR

  I've had OpenSSH server running on my debian server for a couple weeks and all of a sudden now when I go to login the next day it rejects my ssh key and I have to manually add a new one each time. Not only that but I have the "tunneling with clear-text passwords" option enabled and the non-root (login with root is disabled) account for that is rejected too. I'm at a loss why this is happening and I can't find any ssh options that would explain it. --update-- I just changed debug level to DEBUG. But before that I'm seeing a lot of the following in auth.log Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session opened for user root by (uid=0) Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session closed for user root ... Feb 1 04:36:26 greenpages sshd[7217]: reverse mapping checking getaddrinfo for nat-pool-xx-xx-xx-xx.myinternet.net [xx.xx.xx.xx] failed - POSSIBLE BREAK-IN ATTEMPT! ... Feb 1 04:37:31 greenpages sshd[7223]: Did not receive identification string from xx.xx.xx.xx ... My sshd_conf file settings are: # Package generated configuration file # See the sshd(8) manpage for details # What ports, IPs and protocols we listen for Port xxx # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel DEBUG # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM no ClientAliveInterval 60 AllowUsers myuser

  Read the article

• haproxy: Is there a way to group acls for greater efficiency?

  - by user41356

  I have some logic in a frontend that routes to different backends based on both the host and the url. Logically it looks like this: if hdr(host) ends with 'a.domain.com': if url starts with '/dir1/': use backend domain.com/dir1/ elif url starts with '/dir2/': use backend domain.com/dir2/ # ... else if ladder repeats on different dirs elif hdr(host) ends with 'b.domain.com': # another else if ladder exactly the same as above # ... # ... else if ladder repeats like this on different domains Is there a way to group acls to avoid having to repeatedly check the domain acl? Obviously there needs to be a use backend statement for each possibility, but I don't want to have to check the domain over and over because it's very inefficient. In other words, I want to avoid this: use backend domain.com/url1/ if acl-domain.com and acl-url1 use backend domain.com/url2/ if acl-domain.com and acl-url2 use backend domain.com/url3/ if acl-domain.com and acl-url3 # tons more possibilities below because it has to keep checking acl-domain.com. This is particularly an issue because I have specific rules for subdomains such as a.domain.com and b.domain.com, but I want to fall back on the most common case of *.domain.com. That means every single rule that uses a specific subdomain must be checked prior to *.domain.com which makes it even more inefficient for the common case.

  Read the article

• TeamCity sends inadequate responses after Selenium tests

  - by Dmitriy Sukharev

  I have a TeamCity 7.0.2 at CentOS 6.2 server without X Server. I've installed x11-fonts*, xvfb, firefox, xauth, extracted env. variable DISPLAY=localhost:1, and started xvfb. After that I could start Selenium tests using maven. Tests are executed, but there's an issue with TeamCity. Usually TeamCity starts hehaves absolutely inadequate (it confuses images at the page, sends xml or strange text ampersants and numbers in responses and is a bit slower), also tests are executed 4 times slower (1h 15m) at server than at tester Windows 7-based machine (25m). It worth to notice that tests launch two Jetty servers for tested application (one for REST-services application and another for client). In TeamCity I set JVM command line parameters: -Xms256m -Xmx1224m -XX:MaxPermSize=320m, and Additional Maven command line parameters ends with "-DMAVEN_OPTS=-Xmx1024m" (without quotes). Also both web-services and TeamCity uses the same Oracle server (but different Oracle users). Finally TeamCity and its build agent is at the same server. Server has only 4GB of RAM, but during testing there're 400MB of RAM and 1.2GB of swap. TeamCity and Firefox uses about 65% of CPU during testing. There's no firefox process after end of testing. My knowledge about Selenium is weak. I only know that we use 2.20.0 version of selenium-java maven dependency. Please help me to determine why TeamCity sends wrong responces after Selenium tests. I've tried to give you all information I have, but feel free to ask me for more information.

  Read the article

• nginx proxy_pass POST 404 errors

  - by Scott

  I have nginx proxying to an app server, with the following configuration: location /app/ { # send to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } Any request for /app goes to :9001, whereas the default site is hosted on :9000. GET requests work fine. But whenever I submit a POST request to /app/any/post/url it results in a 404 error. Hitting the url directly in the browser via GET /app/any/post/url hits the app server as expected. I found online other people with similar problems and added proxy_set_header Host $http_host; but this hasn't resolved my issue. Any insights are appreciated. Thanks. Full config below: server { listen 9000; ## listen for ipv4; this line is default and implied #listen [::]:80 default_server ipv6only=on; ## listen for ipv6 root /home/scott/src/ph-dox/html; # root ../html; TODO: how to do relative paths? index index.html index.htm; # Make site accessible from http://localhost/ server_name localhost; location / { # First attempt to serve request as file, then # as directory, then fall back to displaying a 404. try_files $uri $uri/ /index.html; # Uncomment to enable naxsi on this location # include /etc/nginx/naxsi.rules } location /app/ { # rewrite here sends to app server without the /app qualifier rewrite /app/(.*)$ /$1 break; proxy_set_header Host $http_host; proxy_pass http://localhost:9001; proxy_redirect http://localhost:9001 http://localhost:9000; } location /doc/ { alias /usr/share/doc/; autoindex on; allow 127.0.0.1; allow ::1; deny all; } }

  Read the article

• Problem configuring Apache/Wordpress on subdomain

  - by friism

  I have two servers (one LAMP, one Windows) and one website with an associated blog. I'm running the main site on the Windows server, and the blog on the LAMP server, using Wordpress. The main site is accessed at http://folketsting.dk (it's in Danish -- sorry), the blog is accessed at http://blog.folketsting.dk (this link is bad, read on). The main site works fine. The blog works, except for the frontpage. Example of working post: http://blog.folketsting.dk/2009/10/09/ftlive/. The frontpage of the blog (http://blog.folketsting.dk) shows html from http://folketsting.dk however (except for the css and javascript). In fact, any other URL than the frontpage "works", and gets served by Wordpress e.g. http://blog.folketsting.dk/foo. I cannot -- for the life of me -- understand how the LAMP server running http://blog.folketsting.dk manages to serve up content generated by the Windows server running http://folketsting.dk. Looking at the response headers at http://blog.folketsting.dk, it's evident that the content originates from Apache, not IIS. I'm pretty sure it's not a DNS-issue, since the problem is evident even when accessing the raw IP, eg. http://130.226.142.141/ vs. http://130.226.142.141/foo. I'm thinking it's a bad config in Apache... any clues?

  Read the article

• On dual boot system, Is it possible to use VirtualBox to boot other installed OS?

  - by Derek Ziemba

  I currently run Windows 7 from a 256GB SSD as my Operating System. Lately, for school, I've been using openSUSE linux inside a VirtualBox PC and I'm really liking it. I'm starting to hate even working in Windows. But I can't just abandon Windows. I've been considering dual booting openSUSE and will likely purchase another SSD for openSUSE. Once I have the dual boot set-up, there is going to be times I need to do something quick in the operating system that I'm not currently in. It would be a pain to have to reboot the computer each time I need to switch the OS for a simple task, especially from Windows since it doesn't let you save it's state. From openSUSE, I want to be able to start a VirtualBox Machine using my Windows Drive. And in Windows, I want to be able to start a VirtualBox Machine of my openSUSE Drive. Would this be possible? The issue I'm worried about is drivers. For instance, the OS will be installed on native hardware and have the native hardware's drivers configured. When I try to boot the OS in a VirtualMachine, I feel like the OS is not going to know what to do, and have to reconfigure itself or just not work.

  Read the article

• Purge print driver cache on windows 7 with powershell script

  - by Doltknuckle

  [Background] We have been having trouble with our network clients suddenly being unable to print. They get an odd error with a hex code. We determined that something in the driver was messed up and we could resolve the issue by clearing the driver cache and reinstalling the driver. This happens to random computers every so often. We're assuming this is a bug with the latest Dell 2330dn driver since that is the only model that has this problem. [Problem] What we are looking to do is write a Powershell script that would clear the driver cache and redownload the driver. I see a ton of scripts out there to manage queues, servers, and ports, but nothing for local driver cache management. [Current Workaround] Since we have to do this manually, I'll write out the steps so you know what we want this script to replicate. Disable print spooler Restart machine Delete contents of: C:\windows\system32\spool\drivers\w32x86 Enable print spooler and start service. Delete the network printer object and re-add network printer off of server. [Request] I'm good enough with powershell to translate the above workaround into a pair of scripts. I'd like to find a more elegant solution then my current workaround. Any suggestions?

  Read the article

• OS X AFP shares and access

  - by gbrandt

  I am running 10.5.6 Client as a mini server and am having problems with AFP shares. All clients are OS X 10.5.7 I have created three users for 'File Sharing' only on the 'server'. I have created groups and placed these users into specific groups. I have created ACL's to give each group access to certain shares. Two of those users can read and write to any share, one user cannot write to the shares, with different results: when copying a directory, only the directory is created, no files inside are copied, the OS does not give any errors when copying a single file I get three dialogs: "You may need to enter the name and password for an administrator on this computer to change the item named 'xxxx', "The item 'xxxxx' contains one or more items you do not have permission to read. Do you want to copy the items you are allowed to read?, and, The operation cannot be completed because you do not have sufficient priveleges for some of the items. With the single file, a file gets created on the server, but is empty. My ACL for the group this user belongs to is: 0: group:projectmembers allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 1: group:informationtechnology inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 2: group:executive inherited allow list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit 3: group:everyone inherited deny list,add_file,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr,writeextattr,readsecurity,file_inherit,directory_inherit User 1 & 2 belong to informationtechnology and executive and projectmembers, they can read and write freely on the share. User 3 belongs to projectmembers and cannot read and write freely. I have read that this is a UID issue, however User 1 & 2 do not have matching UID's across clients and server and they work, so I don't think this is the case. Any ideas?

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

• How do I install the main repositories for RHEL6

  - by eisaacson

  We've setup RHEL6 on a new server. As far as we can tell, our subscription is all setup properly. However, when I run yum repolist, it doesn't show any repositories. /etc/yum.repos.d/redhat.repo is empty. I tried pasting in the content from another RHEL6 server's redhat.repo but as soon as I run yum, it wipes it out again. I just need to get the basic RedHat repositories setup so I can install packages. EDIT: Using the GUI, I went to System Administration Red Hat Subscription Manager. Under the 'Products' tab, it did not show any products. EDIT: When I run yum update, here's what I get: # yum update Loaded plugins: product-id, refresh-packagekit, security, subscription-manager This system is receiving updates from Red Hat Subscription Management. Setting up Update Process No Packages marked for Update When I log in to RedHat customer portal, it shows that subscription as active. EDIT: To make sure I wasn't having a subscription issue. I re-registered and re-subscribed. I get all the same results. # subscription-manager register --force # subscription-manager subscribe --pool=*redacted* EDIT: contents of /etc/yum.conf [main] cachedir=/var/cache/yum/$basearch/$releasever keepcache=0 debuglevel=2 logfile=/var/log/yum.log exactarch=1 obsoletes=1 gpgcheck=1 plugins=1 installonly_limit=3 contents of /etc/yum/pluginconf.d/rhnplugin.conf: [main] enabled = 0 gpgcheck = 1

  Read the article

• Exim and receiving email with large recipient lists

  - by AceJordin

  I have Exim4 running on Debian configured to receive mail on multiple domains. Exim is set to forward all email that is received to one of the domains to another box. This box is configured with a catchall mailbox that everything goes in. My issue is that when an email is sent to the domain, which contains a large amount of addresses (all to the same domain, but different users), Exim will receive the single email over multiple connections. This means that the catchall mailbox receives multiple copies of the single email all containing the full recipient list. For example, I was able to reproduce it by sending an email from my gmail account that contained 500 recipients (eg [email protected]; [email protected]; [email protected]; etc. for a total of 500). Exim received the message as 20 messages (25 recipients per; appears to be a gmail server setting). So the catchall mailbox received 20 messages, each containing all 500 addresses. I'm pretty sure I understand why this is happening but is there any way I can configure Exim to only receive it once, or to combine it into one? Is there anything that can be done on my end, or am I at the mercy of the sending email server? This is causing havoc with a process that polls the catchall mailbox and parses each recipient in each email.

  Read the article

• How to auto-cc a system email account any time a user creates an appointment

  - by Ferdy

  I will not bother explaining my full architecture or reasons for wanting this in order to keep this question short: Is it possible to auto-cc a certain email account any time a Exchange user creates an appointment or meeting in his own calendar? Is it possible using rules? Our Exchange 2007 server is outsourced, I cannot change the configuration or install plugins server-side Preferably, it still should work server-side, because users may use the Outlook client but also Outlook Web Access Is there any other way, perhaps using group policies? My conclusion so far is that the only viable way to accomplish this is to build an Outlook add-on. The problem there is that it will need to be managed for thousands of desktop users and that the add-on will not work when using another client (OWA, mobile). An alternative architecture could be to pull the information from the user's calendar on a scheduled basis. Given that we are talking about a lot of users, scalability is a major issue, this has also been confirmed by Microsoft. Can you confirm that my thinking is correct or do you have any other solutions?

  Read the article

• How do I give a user permisson to view scheduled task history on Server 2008?

  - by pplrppl

  I've set up a scheduled task on Server 2008 and want to run it as a user other than the local administrator. So I choose a domain account created specifically for this task and once I've closed the scheduled task and entered a valid password I want to run it and look a the history tab for this task. On the history tab I see: The user account does not have permission to view task history on this computer. What permission must I grant to allow this user to view history and/or how can I view the history as a local admin/domain admin instead of the user the job will run under? Steps to hopefully reproduce: I'm starting from the "Server Manager" - Configuration - Task Scheduler - Task Scheduler Library. IN the top middle pane I have tasks that have been running for several months as the local administrator. In the process of troubleshooting another issue I changed the task to run as Domain\ABCuser. Later in the process of troubleshooting I tried unchecking "run with highest privileges". I have since changed the job back to SERVERNAME\Administrator but the history tab still showed the permissions message. I may have had multiple Server Manager windows open. After Closing the Server Manager and being sure no other management consoles were open I was able to reopen the Server Manager and see the History tab without error. At this point the task works properly but should I ever need to run a task as a task specific account I'd like to know how to make the history viewable. It may be something as simple as closing all Server Manger windows to allow cached permissions to be refreshed the next time you open the Manager but at this point I don't know exactly what the solution is.

  Read the article

• What determines what resolutions a laptop is willing to output over VGA?

  - by Joshua McKinnon

  I'm responsible for several conference rooms and have setup 1080p projectors and I provide both HDMI and VGA connectivity. HDMI for DisplayPort and Mini-DisplayPort, and VGA as a fallback, universal option. Contrary to what I expected, people seem to have much more trouble with the HDMI than VGA, so VGA gets used a lot more than you'd think (even as most workstation laptops made in the last 3-4 years have DisplayPort or Mini-DisplayPort...). Also to my surprise, VGA outputs over 1080p on a 50ft cable run with very minimal degradation on certain laptops - other laptops just don't offer 1080p as a resolution choice and top out at 1600x1200 or something else. Specific example: a ThinkPad W530 will do 1080p, a W520 won't, over VGA. (both do 1080p over displayport/mini-DP) What determines what resolutions a laptop is willing to output over VGA? I'm thinking this will come down to either a video driver that says it supports only certain resolutions for output, or limitations of the RAMDAC (which wouldn't be in play, at least DAC wise, on a digital output, but WOULD on VGA, an analog output). The basic reason for the question is that I noticed, say, a ThinkPad W520 with 1080p built in display, will output 1080p fine over DisplayPort to a 1080p projector, but will cap out at 1600x1200 (practically the same pixel count, just a little shy) on VGA. Now, this wouldn't be surprising at all except SOME laptops have no issue outputting 1080p over VGA, even with lower native resolutions. Why do I care? Well if there's some way I could enable it... for situations where my users end up using VGA anyway, it's preferable for display mirroring if they can output their laptop's native resolution, which, you guessed it, is very often 1080p on 15" models. DISCLAIMER: This is primarily a curiosity, I'm not claiming 1080p over VGA is ideal by any means, but hey, if it works. I've seen HDMI start artifacting more over same-length, same gauge cabling (up to 50' run in certain rooms). If you think this is better suited to SuperUser, please move it, but this is framed from an IT standpoint of something that affects a real pool of users in a multiple conference room, 50+ deployed laptop scenario.

  Read the article

• Mysql queries stuck in "sending data" state

  - by MarkPW

  I'm running a Litespeed web server and a database server (2 x Clovertown 5335) with MySQL 5.1.52-log (running on Cent OS 4.5 and 4.6 32bit respectively). Last week, I upgraded from 5.0.51a-community-log and since then I've been having a problem whereby my database server's load starts increasing for no apparent reason. Running SHOW PROCESSLIST; I see all of my SQL_CACHE queries that use a wildcard in WHERE, backing up and getting stuck in "sending data" state. However, other queries that use SQL_CACHE but no wildcard do not get caught up in this. To get things going again, the first time it happens (after about 24 hours), I have to restart mysql. 4/5 times it will re-occur after about 20 minutes or so and this time and for subsequent occurrences it is not necessary to restart mysql. Simply stopping the web server for a few minutes will suffice while I allow the stuck queries to clear themselves up. I had no such problem with the the previous mysql install. What could be causing the issue and how do I resolve it? Thanks

  Read the article

• Windows update stuck. Fixt it stuck. So is KB947821. What should I do?

  - by Jim Thio

  I installed a new computer. After I installed I update everything and let the computer runs for days. Then I don't know what my daughter do. The computer stop responding. Windows update no longer work. People said to run fix it. Fix it run and after that the problem still persist and it still doesn't work. The problem changes though. Before there is some error code. Now windows update simply "updating" never end. So I downloaded KB947821. It's been 3 hour and it's still installing. Looks like it hit firewall or something. i don't see windows update on firewall exception list. However, I've never heard that this is an issue. Firewall only protect against incoming transaction, not outgoing right? Or what am I missing. What should I do?

  Read the article

• copSSH and cygwin - Can't use windows style paths

  - by DrFredEdison

  I setup copSSH on one of my windows servers, and within the copSSH bash shell, I can't seem to use windows-style paths to remove and copy files. If I do try, I get the following: $ /bin/cp -r C:/Domains/_temp/collage_push/* C:/Domains/collage/ cygwin warning: MS-DOS style path detected: C:/Domains/_temp/collage_push/ Preferred POSIX equivalent is: /cygdrive/c/Domains/_temp/collage_push/ CYGWIN environment variable option "nodosfilewarning" turns off this warning. Consult the user's guide for more details about POSIX paths: http://cygwin.com/cygwin-ug-net/using.html#using-pathnames I have created a windows environment variable CYGWIN set to nodosfilewarning. It has no effect. I added export CYGWIN=nodosfilewarning to my .bashrc and doing a echo $CYGWIN in my ssh session confirms it is indeed getting set; yet again, it has no effect finally, I noted that when not doing my own export that CYGWIN contains "nontsec binmode" (no quotes), so I tried: export CYGWIN="nodosfilewarning nontsec binmode" in my .bashrc and still no dice. Older versions of CopSSH didn't have this issue. How can I actually override this error? I have a lot of scripts that already use windows-style paths, and I'd rather not change them if possible.

  Read the article

• Ubuntu 10.04 Server on Hyper-V Server R2 has sluggish install and command line

  - by Paul Hobart

  I've installed Ubuntu Server 10.04 (64 bit) on a Hyper-V Server R2. I've encountered two issues that I think are related: Very slow install Very slow command prompt The text-mode installer goes through a series of text-based prompt windows. It takes 7-10 seconds for each of these windows to draw on the screen. The end result is that every time I answer a prompt and hit enter I wait for 15 seconds while the screen redraws line by line. I can literally see each line of text being drawn (like the old 300 baud modems days). Once done installing, scrolling on the command line is super slow. For instance, if a simple command, like "ls", causes the screen to scroll, it will scroll very slowly. This happens on a fresh install. The server functions as a LAMP server and an OpenSSH server, but that's it (I don't even have any Virtual Hosts set up yet). AND this only happens on the Virtual Machine console. I access the console through Hyper-V Manager and don't have this problem on any of my other Virtual Machines. Also, this problem does NOT happen when accessing a shell through OpenSSH. How can I improve this performance issue?

  Read the article

• Getting error ArrayIndexOutOfBoundsException: 2048 at everything I'm doing in Eclipse

  - by Bernhard V

  Hi, whatever I'm doing in Eclipse, I get an error. At start up I get an error at Java tooling initializing. I get an error when I want to open a type. And it's always the same error. For example, when opening a type I get: An internal error occurred during: "Cache refresh". 2048 The error at the start up also prints the error code as 2048. I'm using the most up to date version of Eclipse. Do you know a way to fix this issue? edit: Here the stack trace of the error at Java tooling initializing: java.lang.ArrayIndexOutOfBoundsException: 2048 at org.eclipse.jdt.internal.core.index.DiskIndex.readStreamChars(DiskIndex.java:870) at org.eclipse.jdt.internal.core.index.DiskIndex.initialize(DiskIndex.java:370) at org.eclipse.jdt.internal.core.index.Index.<init>(Index.java:96) at org.eclipse.jdt.internal.core.search.indexing.IndexManager.getIndex(IndexManager.java:248) at org.eclipse.jdt.internal.core.search.indexing.IndexManager.getIndexes(IndexManager.java:309) at org.eclipse.jdt.internal.core.search.PatternSearchJob.getIndexes(PatternSearchJob.java:81) at org.eclipse.jdt.internal.core.search.PatternSearchJob.ensureReadyToRun(PatternSearchJob.java:50) at org.eclipse.jdt.internal.core.search.processing.JobManager.performConcurrentJob(JobManager.java:174) at org.eclipse.jdt.internal.core.search.BasicSearchEngine.searchAllTypeNames(BasicSearchEngine.java:1122) at org.eclipse.jdt.core.search.SearchEngine.searchAllTypeNames(SearchEngine.java:713) at org.eclipse.jdt.internal.ui.dialogs.FilteredTypesSelectionDialog$ConsistencyRunnable.refreshSearchIndices(FilteredTypesSelectionDialog.java:653) at org.eclipse.jdt.internal.ui.dialogs.FilteredTypesSelectionDialog$ConsistencyRunnable.run(FilteredTypesSelectionDialog.java:636) at org.eclipse.jdt.internal.ui.dialogs.FilteredTypesSelectionDialog.reloadCache(FilteredTypesSelectionDialog.java:679) at org.eclipse.ui.dialogs.FilteredItemsSelectionDialog$RefreshCacheJob.run(FilteredItemsSelectionDialog.java:1502) at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP.

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• emacs error: "Symbol's value as variable is void: hostname"

  - by Florian Pilz

  After I installed emacs this error occurs every time on startup. It prevents me from installing plugins, e.g. auctex via aptitude. I already tried to install a plugin by hand (rails for ruby), but doesn't work. The error doesn't contain the message "hostname", but the hostname of my PC is displayed ("bloodredangel-ubuntu"). I changed my hostname to "bloodredangel", but the error message stays the same. While I changed my hostname I saw that in /etc/hostname were two entries: 127.0.0.1 bloodredangel-ubuntu I already asked this question in an ubuntu forum but they couldn't help. They recognised an misconfigured /etc/hosts file, which I corrected, but from time to time these incorrect configurations get attached by something. I didn't add them by hand, maybe it has something to do with the issue. The misconfigurations looked like this: 127.0.0.1 127.0.0.1 bloodredangel-ubuntu localhost.localdomain localhost 127.0.0.1 127.0.0.1:8080 bloodredangel-ubuntu localhost.localdomain localhost I didn't found a solution on the internet, so I hope I will find help here finally.

  Read the article

< Previous Page | 687 688 689 690 691 692 693 694 695 696 697 698  | Next Page >