Search Results

Search found 586 results on 24 pages for '802 11n'.

Page 7/24 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• Can't enable wireless lan on Fujitsu Siemens A1665G with Ubuntu 11.10 installed

  - by Theo

  I saw my old Notebook yesterday and wanted to make that work again. On Windows XP the wireless worked still fine. Then I installed new Ubuntu 11.10 32bit and I'm sadly not able to make the wireless enabled. [I replaced Win XP entirely] lspci lists following network: 08:0a.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) So after recommendation from this link I installed the b43 firmware module. iwconfig prints the following: wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associatd Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management: off As you can see, my wireless lan adapter is not turned on. sudo iwconfig wlan0 txpower auto Doesn't change anything. Then I tried to make it work with rfkill. rfkill list 0: phy0: Wirless LAN Soft blocked: no Hard blocked: yes sudo rfkill unblock all rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes remains the same. The question is now, how I could enable the hard blocked wireless LAN. There is no hardware switch for wlan integrated. However there is a button to change the state. I always thought this would be software sided, but it seems to make some hardware changes as well... The wireless LED is also not blinking (as it did on windows xp) I reset bios and searched for some settings in there, but it has only a few options and nothing to do with wireless settings, nothing works here.. At last I tried to install the acer hotkeys but I was not able to manage that. I installed the acerhkgui package, but in initializing progress, it was not able to compile acer hotkeys for my machine. There was a message that asm/linkage.h was not found while compiling. Do you have any ideas what I could do to make this hard blocked stuff disabled and my wireless card work? PS: I also tried sudo rm /dev/rfkill and a reboot to reinit that stuff... No success :(

  Read the article

• Use Network-Manager to Connect to a wifi Access Point on the command-line

  - by Stefano Palazzo

  I'd like to connect to a wireless access point from the command-line. ideally, I'd only need the name of the AP. But the hardware-address would work as well. I know I can use nmcli to connect to a managed network connection, but in my case, the access point may not be configured for Network-Manager yet (See the difference between the output of nm-tool and nmcli con). Example output of nmcli: Auto pwln 3a3d62b1-bbdf-4f76-b4d2-c211fd5cfb03 802-11-wireless [...] Wired Network aa586921-accf-4932-98c4-c873c310f08e 802-3-ethernet [...] Cisco-UDP Uni 7f94847b-04dc-40b7-9955-5246fb77cc65 vpn [...] T-mobile (D1) 867f345a-cbbf-4bd4-b883-a5e5ae0932f0 gsm [...] Example output of nm-tool: State: connected - Device: eth1 [Auto pwln] ---------------------------------------------------- [...] Wireless Access Points (* = current AP) *pwln: Infra, [...], Freq 2472 MHz, Rate 54 Mb/s, Strength 80 WPA WPA2 WLAN: Infra, [...], Freq 2422 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 [...] How do I connect to an access point that may or may not be known to NM? Extra: Finding out if the connection needs a pass-phrase, and submitting it on the command-line as well would be great too (that is to say It'd be nice if network-manager wouldn't pop open any keyring dialogues or errors on the gui)

  Read the article

• 802.11 Capture Frame

  - by ALi

  I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

  Read the article

• Windows DHCP Server - get notification when a non-AD joined device gets an IP address

  - by TheCleaner

  SCENARIO To simplify this down to it's easiest example: I have a Windows 2008 R2 standard DC with the DHCP server role. It hands out IPs via various IPv4 scopes, no problem there. WHAT I'D LIKE I would like a way to create a notification/eventlog entry/similar whenever a device gets a DHCP address lease and that device IS NOT a domain joined computer in Active Directory. It doesn't matter to me whether it is custom Powershell, etc. Bottom line = I'd like a way to know when non-domain devices are on the network without using 802.1X at the moment. I know this won't account for static IP devices. I do have monitoring software that will scan the network and find devices, but it isn't quite this granular in detail. RESEARCH DONE/OPTIONS CONSIDERED I don't see any such possibilities with the built in logging. Yes, I'm aware of 802.1X and have the ability to implement it long-term at this location but we are some time away from a project like that, and while that would solve network authentication issues, this is still helpful to me outside of 802.1X goals. I've looked around for some script bits, etc. that might prove useful but the things I'm finding lead me to believe that my google-fu is failing me at the moment. I believe the below logic is sound (assuming there isn't some existing solution): Device receives DHCP address Event log entry is recorded (event ID 10 in the DHCP audit log should work (since a new lease is what I'd be most interested in, not renewals): http://technet.microsoft.com/en-us/library/dd759178.aspx) At this point a script of some kind would probably have to take over for the remaining "STEPS" below. Somehow query this DHCP log for these event ID 10's (I would love push, but I'm guessing pull is the only recourse here) Parse the query for the name of the device being assigned the new lease Query AD for the device's name IF not found in AD, send a notification email If anyone has any ideas on how to properly do this, I'd really appreciate it. I'm not looking for a "gimme the codez" but would love to know if there are alternatives to the above list or if I'm not thinking clear and another method exists for gathering this information. If you have code snippets/PS commands you'd like to share to help accomplish this, all the better.

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Windows - Force Wi-Fi to N mode

  - by Frederick Marcoux

  I bought a month ago the D-Link DWA-160 Xtreme N Dual Band USB Adapter and I wonder about the speed. I have a 60Mbps but the speed is never above 300Kbps when I browse Internet or download something. Even from Microsoft or Apple (the fastest server I found). Now on Windows 8, we can see the Wi-Fi stats in Task Manager, there they are: Notice the red rectangle. The signal is 3/5 and I'm about 5 meters far from my router. An Apple Time-Capsule. Also, the connection type is 802.11g, I want N. I made this config in my Device Properties: Does anyone figured out to force the 802.11n in Windows? (Windows 8 preferably)

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• Need advice to choose correct wi-fi drivers for Dell Vostro 3560

  - by overdriven

  I'm having problems with my Dell notebook's Wi-Fi, it can't see some of the available access points, despite they are close and I used to be connected to them yesterday. Other notebooks and my phone can see them. I believe it's a driver issue, since after installing system I haven't downloaded any network drivers. I went to Dell's website to search for them but I have no idea which should I choose. For my Dell Vostro 3560 and system Windows 8.1 64bit these are available: Intel Smart Connect Technology Application APP_iSCT_W8.1_A00_Setup-TJW84_ZPE.exe (23 MB) Vostro-3560_Network_Application_TJW84_WN_4.2.40.2418_A00.EXE (29 MB) Dell Wireless 1704 WLAN 802.11b/g/n (2.4GHz), Bluetooth v4.0+HS Driver DW1704_W8.1_A00_Setup-K1HGN_ZPE.exe (239 MB) Network_Driver_K1HGN_WN_6.30.223.143_A00.EXE (247 MB) Dell Wireless1703 802.11 b/g/n, BT4.0 + HS Driver Dell Wireless1901 802.11a/b/g/n (2.4GHz and 5GHz), Bluetooth v4.0+HS Driver DW1703_DW1901_Win8.1_A00_Setup-7FPWR_ZPE.exe (265 MB) Network_Driver_7FPWR_WN_10.0.0.263_A00.EXE (272 MB) Realtek RTL8105E/RTL8111E Ethernet Controller Driver LOM_Realtek_W8.1_A00_Setup-0XCVW_ZPE.exe (6 MB) Network_Driver_0XCVW_WN_8.018.0621.2013_A00.EXE (12 MB) Intel® Centrino® Wireless-N 2230 Bluetooth Driver BT_Intel_W8.14_A00_Setup-XR83W_ZPE.exe (31 MB) Network_Application_XR83W_WN_3.1.1307.0362_A00.EXE (37 MB)

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• Configure Wireless Network Card

  - by Skizz

  I recently upgraded the wireless network card in my Ubuntu PC from an 802.11g to an 802.11n. Now, it can't see my router. It doesn't appear in the list of networks that is displayed when you click on the NetworkManager icon in Gnome. Other networks are listed and I have connected to them (no password required!). I'm using the Windows driver through ndiswrapper and it can see the card. I tested the card in a Windows PC and everything worked. The router's log doesn't show any messages coming from the wireless card. What have I done wrong? If you need any more information, just leave a comment and I'll get add it to the question.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• How to calculate bandwidth limits per user on WiFi network

  - by Lars

  A typical 802.11g access point can provide around 25 Mbps of bandwidth. How is the bandwidth shared among the users? Furthermore, how many users can be served by a single access point using 802.11g in an environment with low interference, and average web activity from the users? The goal is to use bandwidth limitation to avoid starvation for some users in case some of the users start to download a file or stream HD video or some other bandwidth intensive activity. Can someone break down the math on this?

  Read the article

• Ethernet Connection Unavailable

  - by fabikw

  I'm running Ubuntu Server 12.04 on a laptop with an Intel NIC (driver e1000e). When I connect the ethernet port to the internet (college network, DHCP) it works out of the box. Now I'm trying to connect it to a networked USRP (if you want to know what it is). A friend of mine managed to do this in his laptop (running regular Ubuntu 12.04) just by setting up a new Wired connection in the Network Manager with appropriate addresses. However, when I do the same, no wired connections are available. The output of nmcli -p dev is =========================================== Status of devices =========================================== DEVICE TYPE STATE ------------------------------------------- wlan0 802-11-wireless connected eth0 802-3-ethernet unavailable but the cable is connected to the device and the device is powered up. Any idea how to solve this? UPDATE: After stopping the network-manager service, setting up the connection manually and starting the service again, it now detects the ethernet connection. However, the device still can't receive data and doesn't answer to pings. UPDATE 2: As suggested I tried using a cross over cable but the result is exactly the same. However, I found out that connecting the device to the dock (as opposed to directly to the laptop) works fine. I know that the ethernet port in the laptop works fine, because connecting to the network through it works. Is it possible that the port in the laptop doesn't support Gb Ethernet (because that's what the device requires) but the one in the dock does?

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Building a network at home, what cables to use (if any)?

  - by Faruz

  My house is currently in ruins and am building it. While doing so, I wanted to design a home network. My main objectives are surfing and HD streaming. The house is one-level, 100 sq/m (about 300 sq/ft), and one of the rooms is a safety room with Reinforced concrete walls. About a year ago, when I started planning, I thought about putting Cat 6 STP cables in the walls and create network points in the rooms. Should I use STP or FTP? I heard that STP is a problem regarding connectors and stuff. Is it really beneficial? Will it work OK if I transfer the wire together with the telephone line? Should I maybe go with WLan and count on 802.11n to enable me to stream HD across the house? is 802.11n that good?

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• Encryption over gigabit carrier ethernet

  - by Roy

  I would like to encrypt traffic between two data centres. Communication between the sites is provided as a standard provider bridge (s-vlan/802.1ad), so that our local vlan tags (c-vlan/802.1q) are preserved on the trunk. The communication traverse several layer 2 hops in the provider network. Border switches on both sides are Catalyst 3750-X with the MACSec service module, but I assume MACSec is out of the question, as I don't see any way to ensure L2 equality between the switches over a trunk, although it may be possible over a provider bridge. MPLS (using EoMPLS) would certainly allow this option, but is not available in this case. Either way, equipment can always be replaced to accommodate technology and topology choices. How do I go about finding viable technology options that can provide layer 2 point-to-point encryption over ethernet carrier networks?

  Read the article

• How to Install Broadcom Wireless Drivers (BCM43xx)

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

  Read the article

• Ubuntu 12.04 wireless disabled even though the direct connectin (thru modem) is working fine

  - by user90841

  Need help with my newly installed Ubuntu 12.04 system (dual booting along with Win 7), even thoguh I can use internet using the modem and directly plugging it, the wireless network is disabled and it says firmware missing. I tried the following options: 1) checking to see if the wireless is disabled using the hot keys (F2 or Ctrl+F2, Fn + F2 keys), the wireless is working fine in Win 7 but not in Ubuntu. 2) I am able directly plug the laptop with the modem and able connect to Internet using Ubuntu. 3) From the top right hand menu bar, te Wireless networks options say "device not ready (firmware missing) and the Enable Wireless checkbox is checked. 4) tried the command "rfkill list" , it shows all are NOT blocked. 0: phy0: Wireless LAN soft blocked:no Hard blocked: no 1: dell-wifi: Wireless LAN soft blocked:no Hard blocked: no 2: dell-bluetooth: BlueTooth soft blocked:no Hard blocked: no 3: hci0 Bluetooth soft blocked:no Hard blocked: no 5) ifconfig command shows eth0 and lo (lcoalhost) up and running but the wlan0 option is not available to show unless I type ifconfig -a, when it shows wlan0 but its down. 6) The command lspci -vvnn | grep 14e4 shows 04:00.0 network Controller [0280]: Broadcom Corp BCM4312 802.11b/g LP-PHY [14e4:4315] {rev 01) 08:00.0 Ethernet Controller [0200]: Broadcom Corp Netlink BCM5784M Gigabit Ethernet PCIe [1434:1698] {rev 10) 7) The file /var/lib/NetworkManager/NetworkManager.state shows all options are true (networking enabled, wireless enabled, wwlanenabled and wimaxenabled all options are set to true). 8) 'additional drivers' in your Dash and/or Preferences do not bring up anything at all. 9) output for lshw -C network shows *-network DISABLED description : Wireless interface physical id: 4 logical name: wlan0 serial: 78:e4_00"43:b6:ab capabilities: ethernet physical wireless Configuration: broadcast=yes driver=b43 driverversion=3.2.0.29-generic-pae firmware=N/A link=no multicast= yes wireless=IEEE 802.11bg

  Read the article

• Wireless does not work 12.10

  - by superkoop

  My primary issue is that my wireless does not work after I installed 12.10. The output to rfkill list all: 5: hci0: Bluetooth Soft blocked: no Hard blocked: no The output to lshw -class network is: *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 12 serial: 00:21:9b:d6:46:51 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:44 memory:fe8fc000-fe8fffff ioport:de00(size=256) *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0b:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:17 memory:fe7fc000-fe7fffff The output to lspci -nn for the pertinent information is: 0b:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Thus, it seems the solution would be to run: sudo apt-get install linux-headers-generic sudo apt-get install --reinstall bcmwl-kernel-source sudo modprobe wl However, I do not currently have access to an ethernet connection, as I am currently only able to use verizon wireless 3g internet. Thus, is there a way to set up ICS with a Vista machine so that I can access the internet by using the Vista machine as the host? Or, is it possible to fix this by downloading the important packages in vista and moving them to ubuntu via USB drive?

  Read the article

• Ubuntu Wireless not working on Lenovo t400

  - by VmaxBoss

  This problem started after upgrading to 12.04, an my system is 'up2date' Have tried most of the solution-proposals found on the net. lspci -nnk | grep -iA2 net 00:19.0 Ethernet controller [0200]: Intel Corporation 82567LF Gigabit Network Connection [8086:10bf] (rev 03) Subsystem: Lenovo Device [17aa:20ee] Kernel driver in use: e1000e 03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlagn iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off sudo lshw -C network *-network description: Ethernet interface product: 82567LF Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:22:68:1a:c4:75 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.0.2-k2 duplex=full firmware=1.8-3 ip=192.168.2.154 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:29 memory:fc000000-fc01ffff memory:fc024000-fc024fff ioport:1820(size=32) *-network DISABLED description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:6c:2d:24 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:30 memory:f4300000-f4301fff Please help Br/VB

  Read the article

• NetworkManager detects no networks with a RTL8188CE

  - by Cormac O'Brien

  I'm on a 2011 Lenovo Thinkpad T420i with a Realtek RTL8188CE WiFi adapter. Here's the scenario: I pop in the Ubuntu LiveCD to install. Laptop detects all networks in range, I connect to my home network, internet working great. Once Ubuntu finishes installing, the home network I am connected to is the only one which appears in the applet list. Upon restarting or waking from suspend, NetworkManager does not detect any networks – it simply displays "Disconnected" under the Wireless Network section of the menu. I am able to connect to my home network by using the "Connect to Hidden Wireless Network" option and it works immediately. I have yet to test if this works with other SSIDs. I have tried reinstalling the entire OS as well as NetworkManager and my wireless drivers. For hardware info, I ran: cormac@cormac-T420:~$ sudo lshw -c network Here is the output for my wireless card: *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: d0:df:9a:08:73:50 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-26-generic firmware=N/A ip=192.168.1.138 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:5000(size=256) memory:f2500000-f2503fff I can provide more information if required. This was not a problem in Natty or Oneiric. I hope this can be fixed, I don't want to have to ask for an SSID wherever I need to connect.

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >