Search Results

Search found 14770 results on 591 pages for 'bootable usb drive'.

Page 7/591 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

  • Windows 7 boot from downloaded .iso

    - by Travis
    Downloaded Windows 7 .iso off the net and want to install from USB key on old laptop (previously/still running XP) that has no CD/DVD drive. Here's what I've got so far: Read the instructions in this post: http://kmwoley.com/blog/?p=345 , which were quite straight forward and clear. Properly formatted USB key with another laptop (this one running vista), also with no DVD drive wasn't sure how to make the USB bootable, since my .iso was downloaded and I have no DVD drive. Any help would be much appreciated!!

    Read the article

  • Serve up PC hard drive as USB mass storage

    - by sheepsimulator
    Is there a software package available that can serve up a hard-drive internal to a PC and make it available over USB to other USB Master nodes as mass storage? Ex: take your C: or /dev/hda drive on a PC (let's call the computer PC-A), and run a driver program which makes your C: or /dev/hda drive available to external devices as USB mass storage. When you'd hook up another PC (PC-B) to PC-A via USB, it would detect a USB mass storage device, which is C: or /dev/hda on PC-A. Is this even possible? EDIT: I know that there are other ways of making data on a drive available between two different computers (eg. putting PC-A's hdd in a USB-drive-enclosure, or having PC-A make the hdd available via a network share). But I'd like to know if the method that I describe above is even technically possible.

    Read the article

  • Windows 7 USB power lose after a few seconds / minutes

    - by Stefan Dunn
    My friend's computer has a problem where the USB ports causes problems with the power of some devices connected to the computer. The USB mouse has no problems, however the Wireless Adapter looses power after around 20 seconds of use and USB Flash Drives cause the computer to either freeze, lose power (and become unresponsive) or become disconnected (still shown in Device Manager, but not in My Computer) when trying to transfer any type of file to / from the computer. I have a suspicion it's the Motherboard but could it also be a Software problem? Tried a new case, RAM, CPU and GFX Card which had no effect. The problem occurs on both the Front USB and Back (Motherboard) USB Ports. UPDATE: Tried the USB devices with an Ubuntu Live CD and they work fine, could this mean it's a problem with Windows (x64)?

    Read the article

  • PS/2 vs USB keyboards: performance and energy consumption

    - by Mister Smith
    As far as I know, PS/2 keyboards are interrupt driven, while USB are polled. Typically a PS/2 keyboard was assigned IRQ_1 on Windows. I'm no hardware expert, but at a first glance seems like the PS/2 keyboards are more efficient. So here are my questions: On modern day computers, are PS/2 keyboard better (or faster), and if so, would it be noticeable at all? (e.g.: in gaming) Since they don't need polling, do PS/2 keyboards save energy compared to USB? (notice I'm not talking only about the peripheral here, but about the overall computer energy consumption). In case PS/2 had any advantage over USB, would adding a PS/2 adapter to my USB keyboard make the device as good as an actual PS/2 keyboard? Conversely, would adding a USB adapter to a PS/2 make it as bad as a USB KB? Thanks in advance.

    Read the article

  • I have a password protected USB drive with hidden partition, how to convert to normal USB drive?

    - by deddebme
    I have a generic USB drive which has password protection, and I want to stop this password protection mechanism and to use it as a normal 8GB USB drive. I received this USB drive as a gift in Hong Kong, and there was no instruction menu whatsoever, not even the manufacturer name. When I plug the drive in Windows XP, the removable drive comes up as a read only 5.28MB partition with two files. When I try to add or remove any files or formatting it, it will says the drive is write protected. After launching the Login.exe and typed in the password, a 8GB read/writeable partition will be shown, and I'm free to do anything to it. But once after the drive is unplugged and replugged, the same read only partition will still comes out no matter what I did to the hidden partition. Anyone knows about this kind if USB drive? What did the manufacturer do to hide the partition? Is there a way to "low-level" formatting this drive to convert (or revert) it to a normal drive? Before typing in the password: After typing in the password:

    Read the article

  • How to "restart/repair" an USB port?

    - by Click Ok
    My laptop have 2 usb ports, but one is broken, so I use an USB hub in the another good USB port. In that USB hub, I use a mouse and keyboard. Suddenly, that USB port doesn't detects the mouse and keyboard (even with the light of the hub is on), and the only solution that I found is restarting the laptop. But just some minutes and the keyboard and mouse goes undetected again... So, I wonder if there is some method/software/etc to "restart/repair" the USB port without restart the PC. Thanks for all!

    Read the article

  • Strange behavior of USB HID device

    - by spyder
    I have a device with ARM that work as USB HID. It working well on Windows XP x32 sp 2 and sp 3 (USB 2.0, many PCs), on Windows 7 x32 Ultimate (USB 2.0, Lenovo and HP laptops) but do not work on Windows 7 x64 Home Premium sp1 — plugged and unplugged frequently in USB 2.0 with baloon with "unknown device" in system tray and works not well in USB 3.0 port (MSI all-in-one PC), not all programs can detect it. What can cause this problem? Update. I connected my device via USB hub and everything works fine with it.

    Read the article

  • How to Create a bootable Ubuntu USB flash drive from terminal

    - by Avinash Raj
    Is there any possibility to create a Ubuntu USB flash drive from terminal without using any third-party applications like YUMI,Unetbootin,etc. I tried to create a bootable ubuntu flash drive with dd method, sudo umount /dev/sdb sudo dd if=/path/to/ubuntu.iso of=/dev/sdb bs=1M It create files on the USB disk,but when i try to boot the usb disk it says Operating System Not Found error. Any help will be appreciated!

    Read the article

  • Creating Ubuntu bootable disk on my phone

    - by Aerus
    I want to install Ubuntu 12.04 on my laptop but because I have a complete shortage of writable CDs and DVDs, I wan't to create a bootable USB stick (on Windows). However, the only USB stick I currently have lying around is my HTC phone (HTC Touch HD with 8Gb memory). I was following the Ubuntu guide to create a bootable usb stick with pendrivelinux, however in the last step it shows me that it wants to do more than just copying the .iso file to the USB drive: My question: can I safely proceed without wiping the current OS off my phone (Windows Mobile 6.1) and use it to install Ubuntu?

    Read the article

  • Can Windows tell me what is using my USB drive?

    - by PP
    Being the good citizen I am, I left-click on the "Safely Remove Hardware" icon in my taskbar, and select my USB drive to dismount. Then I get the message: Windows can't stop your 'Generic volume device because it is in use. Close any programs or windows that might be using the device, and then try again later. Of course, being the Operating System, it knows exactly what applications are using my device. So why won't it tell me? As usual, I always end my Vista questions with this plea: anyone know a Microsoft Engineer I can kick?

    Read the article

  • How to create a Windows 7 installation usb media from linux ? (to install Windows 7) - Help need to know better method

    - by Abel Coto
    I have been reading some web pages and posts here and in other forums about how to create a Windows 7 installation Usb media (to install windows 7 using a usb) from linux. I asked in technet about this , and they give me general ideas about how to do it I personally am not very familiar with linux, but basicaly all that you need to do... in whatever way you do it is the following: Format a usb flash drive, either fat32 or ntfs create a partition that is large enough to host the windows installation (give or take 3GB for 64bit, aroudn 2.5gb for 32bit) and mark that partition as active/bootable. Since this can be done with windows, but just as well with a tool like gparted, you should be able to do the same in debian. Once you have created that partition, mount the iso that you download, and copy all files starting from the root, into the root of the usb flash drive. That's all there's to it. There is a method that i found in various places,that is almost the same that the man of technet has said. But,there is a step,that in that method is done,that i don't know if it is really necessary,or not. Not allways dd works.Basically, the missing step was to write a proper boot sector to the usb stick, which can be done from linux with ms-sys. This works with the Win7 retail version. Here is the complete rundown again: Install ms-sys Check what device your usb media is asigned - here we will assume it is /dev/sdb. Delete all partitions, create a new one taking up all the space, set type to NTFS, and set it bootable: *# cfdisk /dev/sdb* Create NTFS filesystem: *# mkfs.ntfs -f /dev/sdb1* Mount iso and usb media: *# mount -o loop win7.iso /mnt/iso # mount /dev/sdb1 /mnt/usb* Copy over all files: *# cp -r /mnt/iso/* /mnt/usb/* Write Windows 7 MBR on usb stick: *# ms-sys -7 /dev/sdb* ...and you're done. Shouldn't the usb work without doing the last step "# ms-sys -7 /dev/sdb" or to make the usb bootable , is a must , not only to mark the partition as bootable ? Would be better use rsync instead of cp -r ? All this steps should be done as root, i suppose , or if not , chmod to 664 and chown the directories where are mounted the usb and the iso, no ? But i suppose that the easier thing is to copy the data as root , and that this will not affect to the data. Has anyone tried this method or some similar like copying the iso with dd ?

    Read the article

  • Having trouble with a workaround, for booting from a usb stick, using grub and a minimal linux kernel to load usb drivers

    - by s hanley
    I'm trying to boot from a usb stick. I formatted it to fat32, and later to ext2, and installed dsl on it using unetbootin, and later the usb install guide on dsl wiki (http://www.damnsmalllinux.org/wiki/index.php/Install_to_USB_From_within_Linux). The bios doesn't have a setting for booting from usb. Grub doesn't "see" the usb drive when I use the root and find commands, explained in (http://www.damnsmalllinux.org/wiki/index.php/USB_Booting). This happens even when I set boot from floppy at the top of the boot order. However, my usb keyboard is recognised by the bios and by grub. How can it recognise the keyboard but not the usb drive? Also, the usb led does flash even before grub starts up, so surely something must be happening usb-wise? I am now following an ubuntu guide to booting from a USB stick, using a hdd-based, minimal linux kernel to supply the usb drivers. But I'm having difficulty adapting it to other OSes (slax/dsl/aptosid). I believe I have to alter the initrd.gz file to include usb drivers and then copy that file along with vmlinuz to a partition on my hdd. But, what's the grub command for the kernel line supposed to look like? From the ubuntu example it's: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper noprompt cdrom-detect/try-usb=true persistent initrd /boot/usb-boot/initrd.lz boot Should mine just be: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz cdrom-detect/try-usb=true initrd /boot/usb-boot/initrd.lz boot

    Read the article

  • few questions on making a flash drive to a hard drive

    - by user23950
    I've found a tutorial here on how to trick the operating system to see a flash drive as a hard drive. http://www.getusb.info/usb-hack-turn-a-usb-stick-into-a-hard-drive-or-local-disk/ But I have a few questions: This trick will only work on the os wherein you updated the flash drive driver. Is there a trick that will work like this one, but if you plug in the flash drive to another computer it will still be treated as hard drive? How do I convert it back to a flash drive?

    Read the article

  • Looking for USB Network Attached Storage (NAS) Adapter that supports multiple drives, NTFS/FAT32 fil

    - by braveterry
    I'm looking for a NAS Adapter that supports attaching multiple USB devices to the network. Here's what I'd like to see in a NAS adapter: Under $100.00. Support for multiple devices. This can be through a USB hub or through multiple USB connectors on the device itself. Bittorrent support would be nice, but this isn't a deal-breaker. Filesystem support for at least NTFS or FAT32. I'd prefer to not have to reformat to use the device, but this is also not a deal-breaker. Here is what I am NOT looking for: I'm NOT looking for a NAS enclosure. I already have a couple of spare external USB drives that I'd like to use. I'm NOT looking for a networked USB hub like the one mentioned here. Network USB hubs only allow access to a drive from one PC at a time. I'm NOT looking for a wireless router with a NAS built in. I already have a wireless router, and I'd rather not go through the hassle of replacing it if possible. What I've looked at so far PogoPlug: This supports multiple devices via a USB hub, but there's not Bittorrent support. It's $99.00, so I may end up going with this and hope that they patch in Bittorrent support later. Addonics NAS Adapter: This supports only one device per adapter, so it's a non-starter. SimpleNET NAS Head USB 2.0 Portable Dongle: I'm not 100% sure this supports multiple devices. Plus there doesn't seem to be any Bittorrent support. I'll try to update this post as I explore other devices.

    Read the article

  • Using a portable USB monitor in Ubuntu 13.04 (AOC e1649Fwu - DisplayLink)

    Having access to a little bit of IT hardware extravaganza isn't that easy here in Mauritius for exactly two reasons - either it is simply not available or it is expensive like nowhere. Well, by chance I came across an advert by a local hardware supplier and their offer of the week caught my attention - a portable USB monitor. Sounds cool, and the specs are okay as well. It's completely driven via USB 2.0, has a light weight, the dimensions would fit into my laptop bag and the resolution of 1366 x 768 pixels is okay for a second screen. Long story, short ending: I called them and only got to understand that they are out of stock - how convenient! Well, as usual I left some contact details and got the regular 'We call you back' answer. Surprisingly, I didn't receive a phone call as promised and after starting to complain via social media networks they finally came back to me with new units available - and *drum-roll* still the same price tag as promoted (and free delivery on top as one of their employees lives in Flic en Flac). Guess, it was a no-brainer to get at least one unit to fool around with. In worst case it might end up as image frame on the shelf or so... The usual suspects... Ubuntu first! Of course, the packing mentions only Windows or Mac OS as supported operating systems and without hesitation at all, I hooked up the device on my main machine running on Ubuntu 13.04. Result: Blackout... Hm, actually not the situation I was looking for but okay can't be too difficult to get this piece of hardware up and running. Following the output of syslogd (or dmesg if you prefer) the device has been recognised successfully but we got stuck in the initialisation phase. Oct 12 08:17:23 iospc2 kernel: [69818.689137] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 12 08:17:23 iospc2 kernel: [69818.800306] usb 2-4: device descriptor read/64, error -32Oct 12 08:17:24 iospc2 kernel: [69819.043620] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 08:17:24 iospc2 kernel: [69819.043630] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 08:17:24 iospc2 kernel: [69819.043636] usb 2-4: Product: e1649FwuOct 12 08:17:24 iospc2 kernel: [69819.043642] usb 2-4: Manufacturer: DisplayLinkOct 12 08:17:24 iospc2 kernel: [69819.043647] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 08:17:24 iospc2 kernel: [69819.046073] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 08:17:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 08:17:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 12 08:17:30 iospc2 kernel: [69825.411220] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 12 08:17:30 iospc2 kernel: [69825.498778] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 12 08:17:30 iospc2 kernel: [69825.498786] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 12 08:17:30 iospc2 kernel: [69825.498909] usbcore: registered new interface driver udl The device has been recognised as USB device without any question and it is listed properly: # lsusb...Bus 002 Device 005: ID 17e9:4107 DisplayLink ... A quick and dirty research on the net gave me some hints towards the udlfb framebuffer device for USB DisplayLink devices. By default this kernel module is blacklisted $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udl#blacklist udlblacklist udlfb and it is recommended to load it manually. So, unloading the whole udl stack and giving udlfb a shot: Oct 12 08:22:31 iospc2 kernel: [70126.642809] usbcore: registered new interface driver udlfb But still no reaction on the external display which supposedly should have been on and green. Display okay? Test run on Windows Just to be on the safe side and to exclude any hardware related defects or whatsoever - you never know what happened during delivery. I moved the display to a new position on the opposite side of my laptop, installed the display drivers first in Windows Vista (I know, I know...) as recommended in the manual, and then finally hooked it up on that machine. Tada! Display has been recognised correctly and I have a proper choice between cloning and extending my desktop. Testing whether the display is working properly - using Windows Vista Okay, good to know that there is nothing wrong on the hardware side just software... Back to Ubuntu - Kernel too old Some more research on Google and various hits recommend that the original displaylink driver has been merged into the recent kernel development and one should manually upgrade the kernel image (and both header) packages for Ubuntu. At least kernel 3.9 or higher would be necessary, and so I went out to this URL: http://kernel.ubuntu.com/~kernel-ppa/mainline/ and I downloaded all the good stuff from the v3.9-raring directory. The installation itself is easy going via dpkg: $ sudo dpkg -i linux-image-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb$ sudo dpkg -i linux-headers-3.9.0-030900_3.9.0-030900.201304291257_all.deb$ sudo dpkg -i linux-headers-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb As with any kernel upgrades it is necessary to restart the system in order to use the new one. Said and done: $ uname -r3.9.0-030900-generic And now connecting the external display gives me the following output in /var/log/syslog: Oct 12 17:51:36 iospc2 kernel: [ 2314.984293] usb 2-4: new high-speed USB device number 6 using ehci-pciOct 12 17:51:36 iospc2 kernel: [ 2315.096257] usb 2-4: device descriptor read/64, error -32Oct 12 17:51:36 iospc2 kernel: [ 2315.337105] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 17:51:36 iospc2 kernel: [ 2315.337115] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 17:51:36 iospc2 kernel: [ 2315.337122] usb 2-4: Product: e1649FwuOct 12 17:51:36 iospc2 kernel: [ 2315.337127] usb 2-4: Manufacturer: DisplayLinkOct 12 17:51:36 iospc2 kernel: [ 2315.337132] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338292] udlfb: DisplayLink e1649Fwu - serial #FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338299] udlfb: vid_17e9&pid_4107&rev_0129 driver's dlfb_data struct at ffff880117e59000Oct 12 17:51:36 iospc2 kernel: [ 2315.338303] udlfb: console enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338306] udlfb: fb_defio enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338309] udlfb: shadow enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338468] udlfb: vendor descriptor length:17 data:17 5f 01 0015 05 00 01 03 00 04Oct 12 17:51:36 iospc2 kernel: [ 2315.338473] udlfb: DL chip limited to 1500000 pixel modesOct 12 17:51:36 iospc2 kernel: [ 2315.338565] udlfb: allocated 4 65024 byte urbsOct 12 17:51:36 iospc2 kernel: [ 2315.343592] hid-generic 0003:17E9:4107.0009: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 17:51:36 iospc2 mtp-probe: checking bus 2, device 6: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 17:51:36 iospc2 mtp-probe: bus: 2, device: 6 was not an MTP deviceOct 12 17:51:36 iospc2 kernel: [ 2315.426583] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.426589] udlfb: Reallocating framebuffer. Addresses will change!Oct 12 17:51:36 iospc2 kernel: [ 2315.428338] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.428343] udlfb: set_par mode 1366x768Oct 12 17:51:36 iospc2 kernel: [ 2315.430620] udlfb: DisplayLink USB device /dev/fb1 attached. 1366x768 resolution. Using 4104K framebuffer memory Okay, that's looks more promising but still only blackout on the external screen... And yes, due to my previous modifications I swapped the blacklisted kernel modules: $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udlblacklist udl#blacklist udlfb Silly me! Okay, back to the original situation in which udl is allowed and udlfb blacklisted. Now, the logging looks similar to this and the screen shows those maroon-brown and azure-blue horizontal bars as described on other online resources. Oct 15 21:27:23 iospc2 kernel: [80934.308238] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 15 21:27:23 iospc2 kernel: [80934.420244] usb 2-4: device descriptor read/64, error -32Oct 15 21:27:24 iospc2 kernel: [80934.660822] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 15 21:27:24 iospc2 kernel: [80934.660832] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 15 21:27:24 iospc2 kernel: [80934.660838] usb 2-4: Product: e1649FwuOct 15 21:27:24 iospc2 kernel: [80934.660844] usb 2-4: Manufacturer: DisplayLinkOct 15 21:27:24 iospc2 kernel: [80934.660850] usb 2-4: SerialNumber: FJBD7HA000778Oct 15 21:27:24 iospc2 kernel: [80934.663391] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 15 21:27:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 15 21:27:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 15 21:27:25 iospc2 kernel: [80935.742407] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 15 21:27:25 iospc2 kernel: [80935.834403] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 15 21:27:25 iospc2 kernel: [80935.834416] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 15 21:27:25 iospc2 kernel: [80935.836389] usbcore: registered new interface driver udlOct 15 21:27:25 iospc2 kernel: [80936.021458] [drm] write mode info 153 Next, it's time to enable the display for our needs... This can be done either via UI or console, just as you'd prefer it. Adding the external USB display under Linux isn't an issue after all... Settings Manager => Display Personally, I like the console. With the help of xrandr we get the screen identifier first $ xrandrScreen 0: minimum 320 x 200, current 3200 x 1080, maximum 32767 x 32767LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm...DVI-0 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm   1366x768       60.0*+ and then give it the usual shot with auto-configuration. Let the system decide what's best for your hardware... $ xrandr --output DVI-0 --off$ xrandr --output DVI-0 --auto And there we go... Cloned output of main display: New kernel, new display... The external USB display works out-of-the-box with a Linux kernel > 3.9.0. Despite of a good number of resources it is absolutely not necessary to create a Device or Screen section in one of Xorg.conf files. This information belongs to the past and is not valid on kernel 3.9 or higher. Same hardware but Windows 8 Of course, I wanted to know how the latest incarnation from Redmond would handle the new hardware... Flawless! Most interesting aspect here: I did not use the driver installation medium on purpose. And I was right... not too long afterwards a dialog with the EULA of DisplayLink appeared on the main screen. And after confirmation of same it took some more seconds and the external USB monitor was ready to rumble. Well, and not only that one... but see for yourself. This time Windows 8 was the easiest solution after all. Resume I can highly recommend this type of hardware to anyone asking me. Although, it's dimensions are 15.6" it is actually lighter than my Samsung Galaxy Tab 10.1 and it still fits into my laptop bag without any issues. From now on... no more single screen while developing software on the road!

    Read the article

  • 2.0 speeds on USB hub?

    - by Matthew Robertson
    How capable are USB hubs? I have an AirPort Extreme router with a printer attached (it's not powered by USB). I want to extend this and add two hard drives (one for Time Machine and the other for EyeTV recordings). Can a 4-port USB hub (I'm considering this one) achieve USB 2.0 speeds and power the hard drives? What difference would a self-powered vs externally-powered hub produce?

    Read the article

  • Getting "boot error" when trying to boot from USB

    - by Jon Ball
    I'm wanting to try out Ubuntu, so followed the instructions for how to install Ubuntu onto a USB. I downloaded the .iso file, then the pendrivelinux 3 part process to make the USB bootable. I can see what looks like a full list of files on the USB (including the wubi.exe application and the syslinux folder). When I try to restart the computer with the USB in, I get the Dell start up screen, and then a black screen with "Boot Error" in the top right hand corner. Setup options (default) are to boot from Removable Device, then Hard Disc. USB is brand new, straight out of the packet. Computer: Dell Inspiron 530S BIOS: 1.0.13 OS: Windows Vista Home Edition USB: EMTEC 8Gb, formatted to FAT32 I've tried some of the tips in other help topics (holding down CTRL key while restarting, removing all other USB devices). I tried to reformat the USB to something other than FAT32, but my only other options were NTFS or exFAT (not FAT16 which was suggested in another topic).

    Read the article

  • Problem with wake after suspend using USB remote.

    - by Bod
    Hi, I'm a linux newbie looking for some help. I'm currently setting up an XBMC HTPC using a laptop and 10.10 and all works great except for waking from resume using the power button on the remote. The suspend works from remote works fine as does the resume using the power button on the laptop. I've checked /proc/acpi/wakeup which initially showed the following. Device S-state Status Sysfs node C096 S5 *disabled pci:0000:00:1e.0 C0F1 S3 *disabled pci:0000:00:1d.0 C0F8 S3 *disabled pci:0000:00:1d.1 C0F9 S3 *disabled pci:0000:00:1d.2 C0FA S3 *disabled pci:0000:00:1d.3 C0FB S3 *disabled pci:0000:00:1d.7 C102 S5 *disabled pci:0000:00:1c.0 C22B S5 *disabled pci:0000:08:00.0 C115 S5 *disabled pci:0000:00:1c.2 C22C S5 *disabled C118 S5 *disabled pci:0000:00:1c.3 C22C S5 *disabled I've since configured the above so that the S3 devices above are enabled. I've confirmed that they are the correct devices using lspci 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) None of this has worked unfortunately and I'm now stuck. It simply refuses to wakeup from the remote. The USB receiver shows no activity LED while suspended. Suspend/resume from the remote works fine from Windows 7 so I know the laptop is ok with it. Any ideas? I need to get this sorted to gain Wife Approval for this system. Thanks, Bod.

    Read the article

  • Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

    - by jgottula
    I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

    Read the article

  • Live USB does not work

    - by MARUF SARKER
    I've made live USB using these "Universal-USB-Installer-1.9.1.9", "unetbootin-windows-581", "YUMI-0.0.8.0" & "LinuxLive USB Creator 2.8.18" in "FAT32" format, but unfortunately I could not boot using the pen-drive. My BIOS supports boot from USB drive. When I am booting from the live usb, it just show black screen with a blinking "_", but nothing happens after that( I have waited more than 10 minutes, but nothing happens). So, can anyone please help me on this? [Additional Info.: I've made Bootable USB using PowerISO and that booted, but it was not possible to access the USB normally afterwards,because PowerISO formatted the USB Drive as RAW(or anything I don't know) and it became 8GB to 700MB, afterwards I had to format it using MiniTool Partition manager.]

    Read the article

  • USB 3.0 randomly disconnecting and reconnecting

    - by user1624552
    I had an old laptop that died so I have bought a new one. I have taken the 2.5 SATA hard drive from the old laptop and I have put it into an external 2.5 SATA enclosure usb 3.0 and I connect it to the new laptop. My new laptop has Windows 8 64 bit installed. When I connect the external hard drive to the new laptop throught USB 3.0 port, it gets randomly disconnecting and reconnecting continuously, even when I am not using it. Also happens if I connect to another usb 3.0 port. Also I have observed that If I connect the external hard drive to a USB 2.0 port instead of an USB 3.0 port all work ok, no randomly disconnection and reconnection occurs. It only happens when I connect it to an USB 3.0 port. Some ideas to solve this issue?

    Read the article

  • How do I execute a file from a FAT USB drive?

    - by Derek Redfern
    I'm trying to install a portable app onto my USB drive such that it is compatible with both Ubuntu and Windows (specifically, a program called eToys). Support is already built into the app for both operating systems - there's etoys.sh for Ubuntu and etoys.exe for Windows. I decided to install onto a FAT drive since that can be read from both systems. This works fine for Windows, but for some reason I cannot execute etoys.sh on Ubuntu. The problem is not with the file - when the whole folder is copied to the local hard drive, the app works great in Ubuntu. But when I try to execute it from the USB, it opens the file in a text editor. I then tried running it from a terminal, but I got the message "Permission denied." I've had the same problem with other executables as well. Is there an easy way to execute things from a USB stick? Thanks! -- Derek

    Read the article

  • What is the difference between installing Ubuntu on a USB device and a laptop hardisk? [duplicate]

    - by Max
    This question already has an answer here: Difference between LiveCD, LiveUSB, full-install, and persistence? 1 answer Now, I have a laptop with Windows 8. For various reasons, I want to install Ubuntu that I can carry with me on the various PCs I work with. The same installation so that I don't have to constantly take care of installing new things and dependencies. Can I do a full installation of Ubuntu in a USB? Can I install softwares and other things in the USB itself so that I can boot it anywhere I want? What is the difference of this installation from full installation on a laptop harddisk? What features will and will not work with the USB option? Thanks!

    Read the article

  • Monitor your Hard Drive’s Health with Acronis Drive Monitor

    - by Matthew Guay
    Are you worried that your computer’s hard drive could die without any warning?  Here’s how you can keep tabs on it and get the first warning signs of potential problems before you actually lose your critical data. Hard drive failures are one of the most common ways people lose important data from their computers.  As more of our memories and important documents are stored digitally, a hard drive failure can mean the loss of years of work.  Acronis Drive Monitor helps you avert these disasters by warning you at the first signs your hard drive may be having trouble.  It monitors many indicators, including heat, read/write errors, total lifespan, and more. It then notifies you via a taskbar popup or email that problems have been detected.  This early warning lets you know ahead of time that you may need to purchase a new hard drive and migrate your data before it’s too late. Getting Started Head over to the Acronis site to download Drive Monitor (link below).  You’ll need to enter your name and email, and then you can download this free tool. Also, note that the download page may ask if you want to include a trial of their for-pay backup program.  If you wish to simply install the Drive Monitor utility, click Continue without adding. Run the installer when the download is finished.  Follow the prompts and install as normal. Once it’s installed, you can quickly get an overview of your hard drives’ health.  Note that it shows 3 categories: Disk problems, Acronis backup, and Critical Events.  On our computer, we had Seagate DiskWizard, an image backup utility based on Acronis Backup, installed, and Acronis detected it. Drive Monitor stays running in your tray even when the application window is closed.  It will keep monitoring your hard drives, and will alert you if there’s a problem. Find Detailed Information About Your Hard Drives Acronis’ simple interface lets you quickly see an overview of how the drives on your computer are performing.  If you’d like more information, click the link under the description.  Here we see that one of our drives have overheated, so click Show disks to get more information. Now you can select each of your drives and see more information about them.  From the Disk overview tab that opens by default, we see that our drive is being monitored, has been running for a total of 368 days, and that it’s health is good.  However, it is running at 113F, which is over the recommended max of 107F.   The S.M.A.R.T. parameters tab gives us more detailed information about our drive.  Most users wouldn’t know what an accepted value would be, so it also shows the status.  If the value is within the accepted parameters, it will report OK; otherwise, it will show that has a problem in this area. One very interesting piece of information we can see is the total number of Power-On Hours, Start/Stop Count, and Power Cycle Count.  These could be useful indicators to check if you’re considering purchasing a second hand computer.  Simply load this program, and you’ll get a better view of how long it’s been in use. Finally, the Events tab shows each time the program gave a warning.  We can see that our drive, which had been acting flaky already, is routinely overheating even when our other hard drive was running in normal temperature ranges. Monitor Acronis Backups And Critical Errors In addition to monitoring critical stats of your hard drives, Acronis Drive Monitor also keeps up with the status of your backup software and critical events reported by Windows.  You can access these from the front page, or via the links on the left hand sidebar.  If you have any edition of any Acronis Backup product installed, it will show that it was detected.  Note that it can only monitor the backup status of the newest versions of Acronis Backup and True Image. If no Acronis backup software was installed, it will show a warning that the drive may be unprotected and will give you a link to download Acronis backup software.   If you have another backup utility installed that you wish to monitor yourself, click Configure backup monitoring, and then disable monitoring on the drives you’re monitoring yourself. Finally, you can view any detected Critical events from the Critical events tab on the left. Get Emailed When There’s a Problem One of Drive Monitor’s best features is the ability to send you an email whenever there’s a problem.  Since this program can run on any version of Windows, including the Server and Home Server editions, you can use this feature to stay on top of your hard drives’ health even when you’re not nearby.  To set this up, click Options in the top left corner. Select Alerts on the left, and then click the Change settings link to setup your email account. Enter the email address which you wish to receive alerts, and a name for the program.  Then, enter the outgoing mail server settings for your email.  If you have a Gmail account, enter the following information: Outgoing mail server (SMTP): smtp.gmail.com Port: 587 Username and Password: Your gmail address and password Check the Use encryption box, and then select TLS from the encryption options.   It will now send a test message to your email account, so check and make sure it sent ok. Now you can choose to have the program automatically email you when warnings and critical alerts appear, and also to have it send regular disk status reports.   Conclusion Whether you’ve got a brand new hard drive or one that’s seen better days, knowing the real health of your it is one of the best ways to be prepared before disaster strikes.  It’s no substitute for regular backups, but can help you avert problems.  Acronis Drive Monitor is a nice tool for this, and although we wish it wasn’t so centered around their backup offerings, we still found it a nice tool. Link Download Acronis Drive Monitor (registration required) Similar Articles Productive Geek Tips Quick Tip: Change Monitor Timeout From Command LineAnalyze and Manage Hard Drive Space with WinDirStatMonitor CPU, Memory, and Disk IO In Windows 7 with Taskbar MetersDefrag Multiple Hard Drives At Once In WindowsFind Your Missing USB Drive on Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows 7’s WordPad is Actually Good Greate Image Viewing and Management with Zoner Photo Studio Free Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer

    Read the article

  • Booting from a USB drive that was originally a boot drive

    - by daveh551
    When Win 7 went RTM, I upgraded my laptop from XP. But to protect myself against the possibility of having data inaccessible, I got a new disk and put it in the laptop, and took the old (XP) disk and put it in a USB enclosure. I have no trouble accessing the data on the USB drive under Windows 7. But I would like to be able to plug it in, tell the BIOS to boot from the USB drive, and be back on my old machine. The laptop is a Dell Precision M90, and it has a boot from USB option in its boot menu. But when I try to do that, it does read the drive, gets as far as putting up the Windows XP splash screen and starting the boot progress bar, and then reboots. What do I need to do to the old disk now running on USB to allow the machine to boot from it?

    Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >