Search Results

Search found 28559 results on 1143 pages for 'upgrade issue'.

Page 701/1143 | < Previous Page | 697 698 699 700 701 702 703 704 705 706 707 708  | Next Page >

  • IPv6 feature in Network Adaptor is Slowing Internet

    - by Teknophilia
    The past few days, my internet browsing has become very poor. It's not a matter of speed, as a speed test will give at least 15Mbps. It seems as if my laptop has a hard time actually connecting to the sites. I've found a possible culprit, but don't know why it would affect anything: Going to adapter settings and disabling ipv6, but leaving ipv4, my browsing is back to normal. Re-enabling ipv6 brings back the issue. This is strange though, because I have always had ipv6 enabled. Moreover, using sites to test ipv6 compatibility, I fail with ipv6 enabled on my adapter, and pass when it's disabled. Ideas about why this is happening, and how to fix it?

    Read the article

  • Poor disk performance with high disk capacity usage

    - by GoldenNewby
    I've heard numerous times in the web hosting industry that using "too much" disk space on a drive is bad for performance. Is this just a myth? Can someone explain why this is an issue, even in a situation where the amount of IO done to the drive would be the same at 10% as it would be at 90%? I'm especially curious in the case of virtual servers. If I set up 10 Logical volumes as the virtual disks for some VMs, is it going to run better if I "waste" 20% of the disk space?

    Read the article

  • Exchange 2007 OWA not listening on SSL port

    - by krs1
    I have an Exchange 2007 server that went down after a power failure. It has OWA access via SSL both externally and internally. OWA is working fine from the internal notwork, however I am getting a timeout when I attempt to connect externally. I pulled up wireshark and noticed that the server actually redirects to SSL. For some reason the server is not listening on the SSL port, and this seems to be causing the timeout. I normally do only development work, but I'm stuck with this since my sysadmin took off for the week and isn't answering my phone calls. As far as I know it shouldn't be a firewall issue. Aside from me not wanting to work on the damn thing, what should I look for?

    Read the article

  • Conditional cPanel Forwarder

    - by Wireblue
    We have many clients on a cPanel server, some of which also have SSL certificates setup. Each year when the renewals are sent to webmaster@ their domain we would like a copy of those emails so we can install the SSL certifciate for them and issue invoices etc. So I'm wondering if there is a way we can selectively or conditionally forward certain emails if they match certain rules? (in cPanel) I'm thinking: If an email is sent to "webmaster@domain" and the subject contains "ssl", then forward to "[email protected]". Any ideas? Thanks in advance, Wireblue

    Read the article

  • How Does Domain Know Where Your Web Host Is Located [closed]

    - by icu222much
    Possible Duplicate: How Does Domain Know Where Your Web Host Is Located? I just purchased a domain name from RapidNames, and a hosting plan at JustHost. I was told to enter JustHost's name server (ns1.justhost.com) in my domain name's name server field and wait for 24 hours for the process to be complete. I do not understand how RapidNames can find my account on JustHost's server as I am sure I am not JustHost's only customer. I have read the article How DNS Works that John Conde has posted, but I still do not understand the issue. After reading several other articles, I am beginning to understand how it works, but I would still like someone to confirm if I am correct or not. From my understanding, linking your domain name to your web host is a two step process. First, you need to tell your domain name who your web host is. This is done by providing the two DNS server addresses. Secondly, you need to tell your web host which domain names you own by entering your domain names into the domain name manager. As a result, when someone queries your domain name, they will be forwarded to your web host. The web host will look in their database to match the domain name the account's owner, and then serve the appropriate website. I want to confirm if my understanding of how a domain knows where your web host is located is accurate?

    Read the article

  • ssh asks for password despite ssh-copy-id

    - by Aliud Alius
    I've been using public key authentication on a remote server for some time now for remote shell use as well as for sshfs mounts. After forcing a umount of my sshfs directory, I noticed that ssh began to prompt me for a password. I tried purging the remote .ssh/authorized_keys from any mention the local machine, and I cleaned the local machine from references to the remote machine. I then repeated my ssh-copy-id, it prompted me for a password, and returned normally. But lo and behold, when I ssh to the remote server I am still prompted for a password. I'm a little confused as to what the issue could be, any suggestions?

    Read the article

  • CSS file not served by IIS 7.5 after multiple clear cache refreshes in a row in browser

    - by KenB
    We are experiencing an interesting issue with IIS 7.5 static caching and a css file. When we use IE to hit the page in question everything works fine - 200 OK on css file. When we refresh the page it works fine - 304 Not Modified on css file. When I refresh again with control key it reloads fine - 200 OK on css file. Now if I do a control key + refresh multiple times in a row really fast the css fails to load and in the developer tools network it says "Loading..." for the css file and it hangs never coming back. Any ideas?

    Read the article

  • Do hard drives have to be mounted somewhere?

    - by TheLQ
    I'm creating a cheap JBOD box with ~7 IDE hard drives. However when you take into account 3 existing drives + 2 CD drives that are installed as well, I am out of mounting places inside the server. Will I adversely affect or harm the drives if I just stack them on top of each other in the box? Before you ask if they are going to fall over, this box won't be moved and won't really be touched while its in use. Heat (should) be taken care of by the fans. However I am worried about the vibrations that each drive will put out. Is this an actual issue?

    Read the article

  • Why are the prices for broadband bandwidth at data centers much higher than consumer/small business offerings?

    - by odemarken
    The prices for broadband bandwidth at data centers are sometimes as much as 10x higher than for a typical small business/consumer connection, at least where I live. Now, I understand those are two differend kind of products, but what exactly are the differences? Is it mainly because the bandwidth you get at a data center is guaranteed (CIR), while a consumer offer lists maximal bandwidth (EIR/MIR)? Or are there other factors as well? (Note: my previous, much more specific question on the same general topic was closed as not constructive. I tried to extract the core issue and present it in a way that can be answered objectively. If you feel that this question is still bad and should be closed, please care to comment and explain why.)

    Read the article

  • Ubuntu 12.04 fresh install wont boot up

    - by user147220
    im running ubuntu 12.04 and it refuses to boot up. the screen will come on for a second, the mosue will appear, then itll go black again all inside about 3 seconds. i let it just do that for a while and eventually a window popped up saying i had a display issue. I didn't have a mouse but there was a button saying "ok" at the bottom that i couldnt click on. i hit enter, got through that screen, now im looking at another that says "What would you like to do?" - run in low-graphics mode for just one session - reconfigure graphics - troubleshoot the error - exit to console login then two buttons, cancel, and ok. I dont have a mouse and its not letting me navigate between these options with tab. firstly, if i make it through these windows will it get me into the computer so i can try and fix whats going on? also, whats going on here? also, how can i click on these buttons without the use of tab or a mouse?

    Read the article

  • How can I move a window that cannot be moved by mouse?

    - by Michael
    I have downloaded a version of Finale Notepad on Windows 7. When I first used it it functioned perfectly. Every time I opened it a popup asking me about downloading a different version would show up that I could just click out of. When the pop up appeared I was unable to quit out of the window or move it at all, but it posed no issue. Apparently, though, the last time I quit out of the program, the screen must have been dragged down below my taskbar. Now, I am unable to quit out of the popup when I reopen the program, meaning I can't access it at all. I tried restarting my computer, uninstalling the program, downloading different versions of the program, and even using alternate methods of moving it, such as Alt+Tab, but nothing works.

    Read the article

  • My sound is not working, so I'm going to reinstall FYI [closed]

    - by fer
    I've had trouble getting the sound to work in Ubuntu 12.04 I'm running an Acer Aspire 5739g laptop. This is using a clean install. This wasn't a problem when ubuntu first installed. Rather, it was when I ran the updates that it stopped working. I already tried the suggestions on the ubuntu sites and other similar queries, and they haven't fixed it. Something in the updates is making my sound not work. Edit: It turns out that this might be a bug (the sound issue, first paragraph). After reinstall, it happened again (it's not caused by updates at all, or any software, because I fixed it now w/o reinstall). It seems like I replicated it as follows: I changed auto-hide in the behavior tab of Appearance settings by turning it on, and setting the sensitivity to below the recommended setting. Then instead of restarting, I just logged out and back in. The sound stopped working again. I set the behavior settings to default, restarted, and now it's back to normal. Not sure if it's due to only logging out (and not restarting) or b/c I set my sensitivity to a low setting. Not sure if this helps anyone, but thought I'd mention it.

    Read the article

  • &quot;The protocol 'net.msmq' is not supported.&quot;

    - by John Breakwell
    The “Lessons Learned” blog has an update covering the error message "The protocol 'net.msmq' is not supported." "The protocol 'net.msmq' is not supported." OMG, a new lesson! Will wonders never cease? So I ran into an interesting issue setting up a WCF service to consume an MSMQ queue. I won't bother you with the details of how to actually build a WCF/MSMQ service; there are plenty of tutorials on the subject. I want to share with you an interesting error that I ran into and the surprisingly simple fix. The error occurs when attempting to generate a Service Reference or even simply browsing to the WSDL of your WCF/MSMQ service in the form of a YSOD with the following error: "The protocol 'net.msmq' is not supported." After a lot of Googling on the subject turning up plenty of questions with the same error but no answers. So I went digging into some application level config files on a server that already had a WCF/MSMQ service successfully set up by the network admin, and the answer was amazingly simple: If you are hosting an MSMQ/WCF service in IIS, you have to tell IIS to allow net.msmq protocol. It's in the advanced settings for the application or site in which you are hosting the service. .... aaaand, that's it.

    Read the article

  • What's the proper way to change a process' scheduling policy to IDLE?

    - by ??O?????
    Hello. I have a long running process on a server running Ubuntu Server 9.10. I would like to make it run under the SCHED_IDLE policy using the chrt command. However, after reading the man page, I can't manage to understand the proper way to issue the command for a running process. I've tried unsuccessfully: # chrt -i -p 688 pid 688's current scheduling policy: SCHED_OTHER pid 688's current scheduling priority: 0 # chrt -p -i 688 pid 688's current scheduling policy: SCHED_OTHER pid 688's current scheduling priority: 0 # chrt -p 688 -i chrt: failed to set pid 0's policy: Invalid argument I'll keep trying, but do you know how to do what I want?

    Read the article

  • How can I get nVidia CUDA or OpenCL working on a laptop with nVidia discrete card/Intel Integrated Graphics?

    - by PeterDC
    Background: I'm a 3D artist (as a hobby) and have recently started using Ubuntu 12.04 LTS as a dual-boot with Windows 7. It's running on my a fairly new 64-bit Toshiba laptop with an nVidia GeForce GT 540M GPU (graphics card). It also, however has Intel Integrated Graphics (which I suspect Ubuntu's been using). So, when I render my 3D scenes to images on Windows, I am able to choose between using my CPU or my nVidia GPU (faster). From the 3D application, I can set the GPU to use either CUDA or OpenCL. In Ubuntu, there's no GPU option. After doing (too much?) research on the issues with Linux and the nVidia Optimus technology, I am slightly more enlightened, but a lot more confused. I don't care one bit about the Optimus technology, as battery life is not by any means an issue for me. Here's my question: What can I do to be able to use CUDA-utilizing programs (such as Blender) on my nVidia GPU in Ubuntu? Will I need nVidia drivers? (I have heard they don't play nicely with Optimus setups on Linux.) Is there at least a way to use OpenCL on my GPU in Ubuntu?

    Read the article

  • IIS7 - multiple ports for websites, some working, some not.

    - by glasnt
    I have multiple IIS7 websites hanging off 1 IP, using different ports. All three sites use Z.A.B.C:XX, where XX is {100, 200, 300} * There's no web.config settings not making :300 not work, the bindings are set ok. I can even change the ports so 200 becomes 300, but the original 300 still doesn't work. They are all shown by IP, so it's not DNS. There's no SSL setting differences between them. I can't see anything in metabase.xml that would make one behave differently to another. Are there any other settings in IIS7 that I might not be finding, that would fix the issue? * not the real values.

    Read the article

  • Can I share data between two users in an ASP.NET Application?

    - by Dave
    I have an issue with Roles.IsUserInRole function. It take hell amount of time to just check if the logged-in user is in particular role(typ 3-9 sec). I searched to find a solution and arrived on this but I am not sure If I have fully grasped it. What I got from the above, A new derived class is created. Inside that class, there is a list which retrieves all user at once. The next time you check IsUserInRole, you do not use the actual IsUserInRole method but rather use the one you overrode in your class. Is this the correct description? Am I on track? My question is, can data be share between two different users in ASP.NET application? If yes, will the shared data exist only if there is at least one user logged in. If all users logs out, that shared data is destroyed? My point is this data will be created only one time whenever a user logs in. For all subsequent users they can use this data and check their roles against the list? I need a detailed answer. My application has users and different roles. We are using ASP.NET roles.

    Read the article

  • Forensics on Virtual Private servers [closed]

    - by intiha
    So these days with talks about having hacked machines being used for malware spreading and botnet C&C, the one issue that is not clear to me is what do the law enforcement agencies do once they have identified a server as being a source or controller of attack/APT and that server is a VPS on my cluster/datacenter? Do they take away the entire machine? This option seems to have a lot of collateral damage associated with it, so I am not sure what happens and what are the best practices for system admins for helping law enforcement with its job while keeping our jobs!

    Read the article

  • VPS name server

    - by rockey
    I bought a new VPS, and configured two applications test1.com and test2.com on ngix server, now I can access both the application inside VPS, Now I need to invoke the application from other machines. MY domain is registerd with Enom, So I added 'A' name pointed to IP address of the VPS, Currently my VPS is not providing any Name Server, So what steps need to be done to resolve the issue regarding Name Server so that i can externally invoke the domains like www.test.com and www.test2.com from other machines? Is any configuration is left from my side other than configuring the Name Server? because it is not working now Thanks in advance

    Read the article

  • HDMI & Display Port stopped work on 11.10

    - by dizzy
    After upgraded two laptops to 11.10, HDMI and Display ports stopped to work. Symptoms on each (btw. it used to work with 11.04 on both): laptop Dell Inspiron 1525 (HDMI, Intel GMX 3100): after HDMI cable is plugged in, screen is corrupted (no panel, no icons), system is unresponsive, TV set receives some signal, but only blue screen and some regular ticks can be heard. Unplugging the cable system recovers. No logs were checked. Thinkpad W510 (DisplayPort, NVidia). Simple "Screens" utility does not recognizes TV set, but this is something to do with the differences between Nvidia driver API and the one expected from the utility, as far I could spot on the net. However, using Nvidia-settings, TV is recognized, but cannot be enabled and used. Beside that, touch pad freezes after HDMI2DisplayPort connector is plugged in the laptop (not immediately, but after few seconds - probably after some handshake with the TV set crashes). It is strange that no such bug reports can be found on the net. So, I guess it is something wrong on our laptops only, but would appreciate some hints (i.e. any known changes recently related to HDMI, Display Port, X-Windows, kernel... wherever I should take a look and fix the issue).

    Read the article

  • Password not accepted when resuming from sleep

    - by Comrade
    My HP Pavilion dv-series notebook will not accept the user account password for the logged in user when resuming from sleep - message returned is Incorrect Password. Simply selecting the Switch User option reloads the login screen and allows me to log in as the same user with the same password that was originally rejected. And, yes I've tried it more than one (hundred) times in case you were thinking it's just a case of slippery fingers. Another interesting point is that it appears to be independent of the software running on the machine. Since the issue first appeared, I have done two clean installs where all HD partitions were wiped and new ones created during fresh installation of the OS. The first such clean install was of Ubuntu (Lucid) 10.04 amd-64, the second of Win 7 Pro 64 (from boxed disc and activated post install). Exactly the same symptoms, described above, are exhibited on both platforms. Have engaged in significant amount of Googling an come up empty so any ideas are welcome.

    Read the article

  • Access Windows VPN DNS from Ubuntu

    - by user46427
    I am using Ubuntu 10.04 to access a Windows VPN. I connect to the VPN from Ubuntu, and when I open a Windows 7 virtual machine (VirtualBox), everything works great ... I can access local network drives, ping local servers, remote into local machines, etc. However, I can do none of this from Ubuntu. With the VPN connected, I cannot even ping anything within the VPN local network. I'm guessing it's a DNS issue that Windows is handling automatically but Ubuntu needs a setting somewhere to tell it to use the DNS servers of the VPN network? Any ideas? I'm a relative novice to Ubuntu, esp. VPN in Ubuntu. [EDIT] Actually, I'm almost positive it is DNS, because if I get the IP address from the Windows VM I can use Terminal Server Client to remote into a machine.

    Read the article

  • Unable to read USB External HD after aborted back up

    - by Stjepan
    I have two PC laptops. On one of the two PC's (Win 7) I Aborted a back up and ejected the drive. Now that same pc wants to format the drive. I plugged the drive into the other pc (Win XP) and that one reads the drive and all data stored. Why does one want to format the drive and the other does not? .... My apologies for not being clearer with my original question and thanks for the responses, so; The drive is not a flash stick, its an external WD Hard drive plugged in via the USB. The two tips provided did not resolve the issue. Strangely, the pc with win XP can read the drive but the pc that the HD was plugged into when the backup was aborted still wants to format the drive. Stjep

    Read the article

  • Extensive use of HDD after VmWare Player virtual machine is closed.

    - by Bobrovsky
    Each time I close virtual machine in VmWare Player I see extensive use of HDD in my system. Basically, whole system becomes unresponsive for about 5-7 minutes. Host system is Windows 7 Utimate x64 SP1 with 6 GB of memory, i3-M350 processor. Virtual machine is Windows XP SP3 x86 (2GB of memory allocated for VM). What can be the cause and what can I do to solve the issue? UPDATE: I am not shutting down the VM, I just close Player window and VM saves it's state. System becomes unresponsive right after VM have saved it state (as indicated by Player) and Player itself have closed.

    Read the article

  • Cannot install Java 7 update 9 32-bit on Win 7 64

    - by J. Parrino
    As there were several versons of Java on my laptop, I decided to uninstall them all and reinstall only the current version. I uninstalled all 64-bit and 32-bit versions using Revo Uninstaller. After dowloading the current versions, when attempting to install them, I get a message that both the 64-bit and 32-bit versions cannot be installed as they are already installed. Both the Windows 7 Programs and Features and Revo show no Java installed at al. I then tried the Microsoft Fixit for install and uninstall issues (KB 2438651). I was then able to install the 64-bit version, but continued to have the issue with the 32-bit version. I ran CCleaner, Glary Utilities and Auslogics Registry Cleaner, and noticed Java keys that were to be uninstalled. After cleaning the registry, I attemped to install the 32-bit version of Java once more, to no avail. Any suggestions on how to rectify this problem? Thank you for any guidance you can provide.

    Read the article

< Previous Page | 697 698 699 700 701 702 703 704 705 706 707 708  | Next Page >