Search Results

Search found 20904 results on 837 pages for 'disk performance'.

Page 703/837 | < Previous Page | 699 700 701 702 703 704 705 706 707 708 709 710  | Next Page >

• Connection speed drops from 1 Gbps to 10 Mbps (Vista 64)

  - by Kevin Hakanson

  I recently got a Windows Home Server (HP MediaSmart Server EX490) setup so I could do backups and other things. However, I am having trouble on my Vista 64 PC. The backup will be making great progress, then it will just slow down. At one point, I noticed the lights on my Netgear GS105 indicated it was not using a 1000 Mbps connection, but a 10 Mbps one. I checked the Status of Local Area Connection (Intel(R) 82567V-2 Gigabit Network Connection) and that also showed the same slow speed. This has happened several times in the last couple days. When I disabled the network device, and then enabled it, it established the 1 Gpbs connection again. However, some of the times the Sent Bytes Activity on the Status windows indicate that the data flow is still slow (100 to 1000 bytes every couple seconds). Obviously, at this rate I could backup faster to floppy disk. :) My question is how to diagnose and fix this problem. When I look at the Administrative Events, I do a Errors: Bonjour Service 456: ERROR: read_msg errno 10054 (An existing connection was forcibly closed by the remote host.) And a Warning: e1yexpress Intel(R) 82567V-2 Gigabit Network Connection Link has been disconnected. I am suspicious there is some power saving mode. I found a post suggesting System Idle Power Saver(SIPS) may be the issue. I am going to try that, but looking for other suggestions or diagnostic advice. I have several new items in this configuration: server, client software, switch and cat6 cables.

  Read the article

• No VMKernel Dump File on PSOD for ESXi 4

  - by user66481

  On PSOD no VMKernel Dump File is written to disk and no message is written to screen (the screen is either blank or full of dashes). I need this data to understand why the system crashes; any help as to how to fix this to write a dump file would be appreciated. Thanks. Notes: VMKCore partition exists, is active, and is configured (esxcfg-dumppart -l). esxcfg-advcfg -g /Misc/PsodOnCosPanic = 1. esxcfg-advcfg -g /Misc/CosCoreFile = /var/core. esxcfg-dumppart -C -D /vmfs/devices/disks/ = "Error running command. Unable to copy the dump partition: Couldn't find a valid VMKernel dump file. Dump partition might be uninitialized." Hardware diagnostics (Dell) checks okay. Hardware: VMWare ESXi 4.1.0 (VMKernel Release Build 320137) Dell Inc. Optiplex 960 (2 Drives) Intel Core 2 Quad CPU Q9400 2.66GHz Configuration: 2 Virtual Machines: Windows Server 2003 R2 Enterprise Edition SP2 (1 on each drive) VM 1: Executes Batch Jobs (Has Internet Information Services 6) VM 2: Database Server (Has SQL Server 2000)

  Read the article

• Use RAID for desktop computer?

  - by NickAldwin

  I'm building a new computer over the summer. I'm fairly competent in computer hardware, and am thus building the computer from scratch. I have everything planned out, but I was wondering if I should consider RAID/what RAID to use. I plan to purchase 2x1TB drives. Currently I'm leaning toward RAID 1 for the redundancy -- I've heard newer super-capacity drives fail more often than one would think, and I don't want to have a problem and lose all my data. What do you think? My mobo supports RAID 0/1/5/10. Is it worth it to use RAID at all, or should I just use a backup service like Mozy? Should I consider RAID 0 instead, for the performance? I'm kind-of going back and forth on this one. Thanks a lot for your help. EDIT: I'd like to avoid the OS drive different from Data drive situation, because that can get frustrating when programs like to store a lot of data in their program files folder. I've lived with that situation before and it gets annoying after a while.

  Read the article

• Toshiba Portege M400 screen rotation not working under Windows 7 x64

  - by Christi

  I have installed Windows 7 on my Toshiba Portege M400. This in itself was relatively tricky.* However, the button utilities aren't quite working for me. One of the buttons tries to launch the Toshiba Assist program, which doesn't appear to be available under Windows 7 for the M400, but this I can live without. More important is that the screen won't rotate as it is supposed to when you hold the "cancel" (X in a circle) button on the bezel. The PC is set to run "C:\Program Files (x860\Toshiba\Toshiba Rotation Utility\phtrot.exe". There is a "trot.exe" file in the same directory (the former appears to be to cause slightly different behaviour when rotation is done by press and hold). Neither of these programs rotates the screen either by using the buttons or from the command line. The screen is rotating normally when switching from tablet to laptop mode, so there does not appear to be an inherent problem with rotation. I'd just like to be able to use the buttons on the side of the screen to change the screen orientation. Windows XP used to have a "setrot" utility to do this, but that seems to have gone in Windows 7 Thanks for your help. *Just in case anyone comes looking for how to do this, you need to extract driver files from http://cdgenp01.csd.toshiba.com/content/support/downloads/util_raid_os2007252a.exe, which does not seem to be listed among the available files for the m400. This executable contains the SATA interface drivers that will need to be loaded by the installer before it can see your hard disk drive. It needs to be unpacked and the files copied to a USB key which they can then be loaded from in the install process. The utilities etc. for installation post windows install are all available from the Toshiba USA support website.

  Read the article

• Samba: share home directories when home directories are symbolic links

  - by Owen

  I have set up a new Ubuntu 9.10 system for five users. In the system is a large LVM volume where all the data is to be kept. The main system disk is not for this purpose, so I attempted to move the home directories using usermod -d /var/data/username -m And started creating my shares for these new home locations. But then I thought: hey, Samba has built-in home directory sharing! So I enabled that, and it didn't work. The shares were not published to the network. Only the share for user 'owen' was published; his folder hadn't been moved. So I thought: maybe Samba home sharing only works for default home locations, so how about I move the home directories back to where they were, and then make them symlinks. root@boxenmkiv:/home# ls -l total 4 lrwxrwxrwx 1 brett brett 25 2010-04-03 08:48 brett -> /var/data/brett/ lrwxrwxrwx 1 carly carly 23 2010-04-03 08:48 carly -> /var/data/carly/ lrwxrwxrwx 1 dave dave 21 2010-04-03 08:48 dave -> /var/data/dave/ lrwxrwxrwx 1 kate kate 23 2010-04-03 08:47 kate -> /var/data/kate/ drwxr-xr-x 4 owen owen 4096 2010-04-03 08:44 owen Like so. Still no go. The only users share which is published to the network is 'owen' who as you can see above has not had his home directory moved. I have also added the following to my smb.conf [global] follow symlinks = yes wide symlinks = yes unix extensions = no With no luck. Am I going about doing this the entirely wrong way? Should I just give up and manually create shares for the users? Thanks in advance.

  Read the article

• How can I forward an application with X11 in grayscale

  - by ??????? ???????????

  I am trying to run a graphical application at home and display it on a it on a laptop which is located about six routing hops away. The problem is that the connection is so slow (or rather there is so much GOOEY being transfered) that the mouse is unresponsive and it takes a "long time" to redraw the window even at a resolution of 800x600 pixels. The connection speeds are 10MBit up at home and about 1MBit down on the laptop, which I think should be sufficient for looking at some GUI in (almost) real time. Since this traffic is sent over over a secure shell, I have enabled Compression with highest CompressionLevel along with Ciphers set to blowfish-cbc. This has substantially improved the responsiveness of the application, making it nearly usable. However, my goal is to improve the performance even further by sacrificing colors and even frame rate. The application to be displayed a Qemu SDL window with a graphically-oriented OS in it. This is not strictly relevant, but perhaps there are options to tweak the SDL output which I am not aware of. A possible workaround would be to run the application in a "hidden" X server and enabling TigerVNC on that X server. This would automatically give me the benefits of an optimized VNC viewport, but the goal is to do without (reduce complexity). The question I'm asking is what are my options for reducing the data-rate generated on the server in order to make the graphical application more usable on the client. As mentioned, colors are not important and I could probably work with 5-16 fps. Both machines are running Gentoo with the software in question being: workstation X.Org X Server 1.10.4 OpenSSH_5.8p1-hpn13v10, OpenSSL 1.0.0e QEMU emulator version 0.15.1 (qemu-kvm-0.15.1) laptop X.Org X Server 1.12.2 OpenSSH_5.8p1-hpn13v10lpk, OpenSSL 1.0.0j

  Read the article

• kickstart: reference floppy drive via %ksappend or %include

  - by virtualeyes

  Having trouble getting %ksappend or %include to work when referencing a local floppy drive. Booting off remote server's cd-rom drive I am able to load the CentOS 6 minimal install image, and then add ks=hd:fd0/ks-jvm.cfg to boot params to load kickstart init file from floppy disk. That works fine. The problem is that I want to load a streamlined generic init file off the floppy and then, within the init, %ksappend or %include specific config files relative to the type of server I'm building (JVM, MySQL, Apache, etc.) I do not have DHCP, networking needs to be specified statically, so %ksappend and %include both fail when attempting to reference http://some-LAN-IP/foo.cfg since networking has not yet been set. The kickstart setup only works when I glob in the entire config into a single file, which is great, but ugly and difficult to maintain when I return later, having forgotten the original setup. At this point I'd be happy if I could get %ksappend or %include working with a floppy drive reference in the %post section; that would consolidate a lot of common boilerplate that all kickstarts will rely on (sshd_config, rsync config, resolve.conf, and so on) Thanks for providing the magic floppy drive reference that is eluding me!

  Read the article

• Error when restoring database (Windows 7 test environment)

  - by Undh

  I have a windows 7 operating system as a test environment. I have SQL Server EE installed with two instances, named as test and production. I took a full backup from AdventureWorks database from test instance and I tried to restore it into the production instance: RESTORE DATABASE [testikanta] FROM DISK = N'C:\Program Files\Microsoft SQL Server\MSSQL10.SQL2008TESTI\MSSQL\Backup\AdventureWorks.bak' WITH FILE = 1, NOUNLOAD, REPLACE, STATS = 10 GO I got an error saying: Msg 3634, Level 16, State 1, Line 1 The operating system returned the error '32(failed to retrieve text for this error. Reason: 15105)' while attempting 'RestoreContainer::ValidateTargetForCreation' on 'C:\Program Files\Microsoft SQL Server\MSSQL10.SQL2008TESTI\MSSQL\DATA\AdventureWorks_Data.mdf'. Msg 3156, Level 16, State 8, Line 1 File 'AdventureWorks_Data' cannot be restored to 'C:\Program Files\Microsoft SQL Server\MSSQL10.SQL2008TESTI\MSSQL\DATA\AdventureWorks_Data.mdf'. Use WITH MOVE to identify a valid location for the file. Msg 3634, Level 16, State 1, Line 1 The operating system returned the error '32(failed to retrieve text for this error. Reason: 15105)' while attempting 'RestoreContainer::ValidateTargetForCreation' on 'C:\Program Files\Microsoft SQL Server\MSSQL10.SQL2008TESTI\MSSQL\DATA\AdventureWorks_Log.ldf'. Msg 3156, Level 16, State 8, Line 1 File 'AdventureWorks_Log' cannot be restored to 'C:\Program Files\Microsoft SQL Server\MSSQL10.SQL2008TESTI\MSSQL\DATA\AdventureWorks_Log.ldf'. Use WITH MOVE to identify a valid location for the file. Msg 3119, Level 16, State 1, Line 1 Problems were identified while planning for the RESTORE statement. Previous messages provide details. Msg 3013, Level 16, State 1, Line 1 RESTORE DATABASE is terminating abnormally. Where's the problem? I'm running these instances as on local machine adminstrator (SQL Server services are running with the same account).

  Read the article

• Ubuntu virtual memory caches suck up memory

  - by Tom

  Hey all, I've got an Ubuntu 9.10 64-bit server that seems to use up all available memory. According to my munin graphs, almost all of the memory used up is in the swap cache, cache, and slab cache. (I take this to mean virtual memory caches, am I right in assuming this?) Once memory usage approaches 100%, some (although not all) system services such as SSH become sluggish and unresponsive. After rebooting the system, performance and memory usage become normal for a time. Some interesting tidbits: The system runs Apache 2, MySQL, Munin, and sshd. The memory usage spikes happen at the same time every night (at 10 PM sharp.) There appears to be nothing in the crontab for any of the users, and nothing in /etc/cron.d/* out of the ordinary, let alone something that would occur at 10 PM. My question is, how do I figure out what is causing the memory suckage? I've tried the usual utilities (e.g. ps, top, etc) but I can't seem to find anything unusual. Any ideas? Thanks in advance!

  Read the article

• Ext3 fs: Block bitmap for group 1 not in group (block 0). is fs dead?

  - by ip

  Hi, My company has a server with one big partition with Mysql database and php files. Now this partition seems to be corrupted, as reported from kernel messages when I tried to mount it manually: [329862.817837] EXT3-fs error (device loop1): ext3_check_descriptors: Block bitmap for group 1 not in group (block 0)! [329862.817846] EXT3-fs: group descriptors corrupted! I've tried to recovery it running tools from a PLD livecd. These are the tools I have tested: - e2retrieve - testdisk - photorec - dd_rescue/dd_rhelp - ddrescue - fsck.ext2 - e2salvage without any success. dumpe2fs 1.41.3 (12-Oct-2008) Filesystem volume name: /dev/sda3 Last mounted on: <not available> Filesystem UUID: dd51610b-6de0-4392-a6f3-67160dbc0343 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal filetype sparse_super Default mount options: (none) Filesystem state: not clean with errors Errors behavior: Continue Filesystem OS type: Linux Inode count: 9502720 Block count: 18987570 Reserved block count: 949378 Free blocks: 11555345 Free inodes: 11858398 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 16384 Inode blocks per group: 512 Last mount time: Wed Mar 24 09:31:03 2010 Last write time: Mon Apr 12 11:46:32 2010 Mount count: 10 Maximum mount count: 30 Last checked: Thu Jan 1 01:00:00 1970 Check interval: 0 (<none>) Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 128 Journal inode: 8 Journal backup: inode blocks dumpe2fs: A block group is missing an inode table while reading journal inode There's any other tools I have to test before considering these disk definitely unrecoverable? Many thanks, ip

  Read the article

• VMWare ESX, storage over 2TB

  - by Phliplip

  Hi, First of, i'm a webdeveloper and my server experience lies in setting up FreeBSD servers for webserver. I'm working on a project for at photographer, and i'm hired to develop a new online photo ordering system - where user of course can view their photos :) They have a massive need of storage, thus we have bought a HP G6 and 8x1TB SATA HDD. Our plan is to install VMWare ESX 4.0, running multiple virtual machines; FreeBSD 8 for webserver and some windows servers. Allready done that. Then mount one big storage to the BSD, and share it through Samba to the WinServers. The raid is set up with an array of 2x 1TB to handle the VMs. And the rest is setup as 3 2x1TB to handle the photo-data. Thus 2.73TB for photo-data (the raids are 1+0). Now if we add a datastore in the ESX and add the 3 LUNs we can get a datastore of 2.74TB. But i don't se how i can add this datastore direct to the VM. Only the BSD VM needs access to this. Only way is to create a VirtualDisk, with a max of 2TB (8MB blocksize). This is because the datastore where we save the virtualdisk has a maximum filesize of 2TB. Then add it as a harddisk to the BSD VM. In the 'Add Harddisk' pane for the VM, i see an option for Raw Disk Management. I think this is to access the datastore or the raid directly. Only problem is that its greyed out! Can i access the datastorage directly from the BSD? Without creating and adding virtualdisk.

  Read the article

• Simple P2V help from Linux to Windows

  - by Ke.

  I have two OS's installed on different drives in my PC. One linux (Centos 5.4) and one windows 7. Its getting tiresome to constantly have to stop and restart the PC when I want to use either OS. I would very much like to use Windows 7 as my host OS and access my linux OS from within Windows. However, im having trouble deciphering exactly how to do this (many of the articles seem confusing and a bit overkill) From what i have seen its possible to use VMWare converter to convert the physical linux image to a virtual image so that I can use it in windows. As im having problems understanding how this is done, I would really appreciate a step by step guide (for a newbie), or any simple tutorials that you can point me at. Some questions beforehand: 1) My linux image is around 80gb, do i need to take this into consideration? The linux drive is around 180gb in total. All my other drives are NTFS non writeable in linux (as I use them in windows and ntfs is dodgy in linux), so probably not possible to move the image over to my ntfs drives 2) Can I just zip the linux files up somehow and transfer it to windows to create the p2v? 3) Is it possible to do the P2V conversion while I am logged into windows. I can see the actual linux drive loaded in disk manager, but windows doesnt read linux file systems so im confused as to how to access the linux drive if this is possible. 4) Or will i need to do the whole p2v conversion inside linux? Cheers, any help is much appreciated Ke (a confused p2v newbie)

  Read the article

• Remove Kernel Lock from Unmounted Mass Storage USB Device from the Command Line in Linux

  - by Casey

  I've searched high and low, and can't figure this one out. I have a older Olympus Camera (2001 or so). When I plug in the USB connection, I get the following log output: $ dmesg | grep sd [20047.625076] sd 21:0:0:0: Attached scsi generic sg7 type 0 [20047.627922] sd 21:0:0:0: [sdg] Attached SCSI removable disk Secondly, the drive is not mounted in the FS, but when I run gphoto2 I get the following error: $ gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') *** What command will unmount the drive. For example in Nautilus, I can right click and select "Safely Remove Device". After doing that, the /dev/sg7 and /dev/sdg devices are removed. The output of gphoto2 is then: # gphoto2 --list-config /Camera Configuration/Picture Settings/resolution /Camera Configuration/Picture Settings/shutter /Camera Configuration/Picture Settings/aperture /Camera Configuration/Picture Settings/color /Camera Configuration/Picture Settings/flash /Camera Configuration/Picture Settings/whitebalance /Camera Configuration/Picture Settings/focus-mode /Camera Configuration/Picture Settings/focus-pos /Camera Configuration/Picture Settings/exp /Camera Configuration/Picture Settings/exp-meter /Camera Configuration/Picture Settings/zoom /Camera Configuration/Picture Settings/dzoom /Camera Configuration/Picture Settings/iso /Camera Configuration/Camera Settings/date-time /Camera Configuration/Camera Settings/lcd-mode /Camera Configuration/Camera Settings/lcd-brightness /Camera Configuration/Camera Settings/lcd-auto-shutoff /Camera Configuration/Camera Settings/camera-power-save /Camera Configuration/Camera Settings/host-power-save /Camera Configuration/Camera Settings/timefmt Some things I've tried already are sdparm and sg3_utils, however I am unfamiliar with them, so it's possible I just didn't find the right command. Update 1: # mount | grep sdg # mount | grep sg7 # umount /dev/sg7 umount: /dev/sg7: not mounted # umount /dev/sdg umount: /dev/sdg: not mounted # gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') ***

  Read the article

• Error 0x80300001 Installing Windows Server 2008 R2 64bit on FastTrak TX4660 RAID volume

  - by Konstantin Boyandin

  I am trying to install Windows Server 2008 R2 Enterprise 64bit on the following hardware: motherboard Intel DBS1200BTL Promise FastTrak TX4660 RAID controller 4 disks set up in two RAID1 arrays (handled by FastTrak) I am trying to install Windows so it would boot from RAID1 volume created with the FastTrak controller. The installation goes as in the manual, I insert the disk with the driver, select 'Browse' and specify the correct driver, it finds all the RAID arrays but notifies me that error 0x80300001 happened, Windows can't be installed on the mentioned RAID volumes, since they may not be bootable (even though the target RAID volume is the first in boot options list). If I proceed with the installation, Windows copies and unpacks itself, performs other standard actions after that. After the computer is restarted, it won't boot (Windows Boot Manager appears in the boot devices list; however, neither it nor the RAID volume itself does not boot). Is it a known problem? I can attach the boot disks to the motherboard and use its RAID capabilities instead, but I'd prefer FastTrak ones. Driver version is 1.3.0.4. Thanks.

  Read the article

• What tells initramfs or the Ubuntu Server boot process how to assemble RAID arrays?

  - by Brad

  The simple question: how does initramfs know how to assemble mdadm RAID arrays at startup? My problem: I boot my server and get: Gave up waiting for root device. ALERT! /dev/disk/by-uuid/[UUID] does not exist. Dropping to a shell! This happens because /dev/md0 (which is /boot, RAID 1) and /dev/md1 (which is /, RAID 5) are not being assembled correctly. What I get is /dev/md0 isn't assembled at all. /dev/md1 is assembled, but instead of using /dev/sda2, /dev/sdb2, /dev/sdc2, and /dev/sdd2, it uses /dev/sda, /dev/sdb, /dev/sdc, /dev/sdd. To fix this and boot my server I do: $(initramfs) mdadm --stop /dev/md1 $(initramfs) mdadm --assemble /dev/md0 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 $(initramfs) mdadm --assemble /dev/md1 /dev/sda2 /dev/sdb2 /dev/sdc2 /dev/sdd2 $(initramfs) exit And it boots properly and everything works. Now I just need the RAID arrays to assemble properly at boot so I don't have to manually assemble them. I've checked /etc/mdadm/mdadm.conf and the UUIDs of the two arrays listed in that file match the UUIDs from $ mdadm --detail /dev/md[0,1]. Other details: Ubuntu 10.10, GRUB2, mdadm 2.6.7.1 UPDATE: I have a feeling it has to do with superblocks. $ mdadm --examine /dev/sda outputs the same thing as $ mdadm --examine /dev/sda2. $ mdadm --examine /dev/sda1 seems to be fine because it outputs information about /dev/md0. I don't know if this is the problem or not, but it seems to fit with /dev/md1 getting assembled with /dev/sd[abcd] instead of /dev/sd[abcd]2. I tried zeroing the superblock on /dev/sd[abcd]. This removed the superblock from /dev/sd[abcd]2 as well and prevented me from being able to assemble /dev/md1 at all. I had to $ mdadm --create to get it back. This also put the super blocks back to the way they were.

  Read the article

• high load average, high wait, dmesg raid error messages (debian nfs server)

  - by John Stumbles

  Debian 6 on HP proliant (2 CPU) with raid (2*1.5T RAID1 + 2*2T RAID1 joined RAID0 to make 3.5T) running mainly nfs & imapd (plus samba for windows share & local www for previewing web pages); with local ubuntu desktop client mounting $HOME, laptops accessing imap & odd files (e.g. videos) via nfs/smb; boxes connected 100baseT or wifi via home router/switch uname -a Linux prole 2.6.32-5-686 #1 SMP Wed Jan 11 12:29:30 UTC 2012 i686 GNU/Linux Setup has been working for months but prone to intermittently going very slow (user experience on desktop mounting $HOME from server, or laptop playing videos) and now consistently so bad I've had to delve into it to try to find what's wrong(!) Server seems OK at low load e.g. (laptop) client (with $HOME on local disk) connecting to server's imapd and nfs mounting RAID to access 1 file: top shows load ~ 0.1 or less, 0 wait but when (desktop) client mounts $HOME and starts user KDE session (all accessing server) then top shows e.g. top - 13:41:17 up 3:43, 3 users, load average: 9.29, 9.55, 8.27 Tasks: 158 total, 1 running, 157 sleeping, 0 stopped, 0 zombie Cpu(s): 0.4%us, 0.4%sy, 0.0%ni, 49.0%id, 49.7%wa, 0.0%hi, 0.5%si, 0.0%st Mem: 903856k total, 851784k used, 52072k free, 171152k buffers Swap: 0k total, 0k used, 0k free, 476896k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3935 root 20 0 2456 1088 784 R 2 0.1 0:00.02 top 1 root 20 0 2028 680 584 S 0 0.1 0:01.14 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.12 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 7 root 20 0 0 0 0 S 0 0.0 0:00.16 ksoftirqd/1 8 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1 9 root 20 0 0 0 0 S 0 0.0 0:00.42 events/0 10 root 20 0 0 0 0 S 0 0.0 0:02.26 events/1 11 root 20 0 0 0 0 S 0 0.0 0:00.00 cpuset 12 root 20 0 0 0 0 S 0 0.0 0:00.00 khelper 13 root 20 0 0 0 0 S 0 0.0 0:00.00 netns 14 root 20 0 0 0 0 S 0 0.0 0:00.00 async/mgr 15 root 20 0 0 0 0 S 0 0.0 0:00.00 pm 16 root 20 0 0 0 0 S 0 0.0 0:00.02 sync_supers 17 root 20 0 0 0 0 S 0 0.0 0:00.02 bdi-default 18 root 20 0 0 0 0 S 0 0.0 0:00.00 kintegrityd/0 19 root 20 0 0 0 0 S 0 0.0 0:00.00 kintegrityd/1 20 root 20 0 0 0 0 S 0 0.0 0:00.02 kblockd/0 21 root 20 0 0 0 0 S 0 0.0 0:00.08 kblockd/1 22 root 20 0 0 0 0 S 0 0.0 0:00.00 kacpid 23 root 20 0 0 0 0 S 0 0.0 0:00.00 kacpi_notify 24 root 20 0 0 0 0 S 0 0.0 0:00.00 kacpi_hotplug 25 root 20 0 0 0 0 S 0 0.0 0:00.00 kseriod 28 root 20 0 0 0 0 S 0 0.0 0:04.19 kondemand/0 29 root 20 0 0 0 0 S 0 0.0 0:02.93 kondemand/1 30 root 20 0 0 0 0 S 0 0.0 0:00.00 khungtaskd 31 root 20 0 0 0 0 S 0 0.0 0:00.18 kswapd0 32 root 25 5 0 0 0 S 0 0.0 0:00.00 ksmd 33 root 20 0 0 0 0 S 0 0.0 0:00.00 aio/0 34 root 20 0 0 0 0 S 0 0.0 0:00.00 aio/1 35 root 20 0 0 0 0 S 0 0.0 0:00.00 crypto/0 36 root 20 0 0 0 0 S 0 0.0 0:00.00 crypto/1 203 root 20 0 0 0 0 S 0 0.0 0:00.00 ksuspend_usbd 204 root 20 0 0 0 0 S 0 0.0 0:00.00 khubd 205 root 20 0 0 0 0 S 0 0.0 0:00.00 ata/0 206 root 20 0 0 0 0 S 0 0.0 0:00.00 ata/1 207 root 20 0 0 0 0 S 0 0.0 0:00.14 ata_aux 208 root 20 0 0 0 0 S 0 0.0 0:00.01 scsi_eh_0 dmesg suggests there's a disk problem: .............. (previous episode) [13276.966004] raid1:md0: read error corrected (8 sectors at 489900360 on sdc7) [13276.966043] raid1: sdb7: redirecting sector 489898312 to another mirror [13279.569186] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [13279.569211] ata4.00: irq_stat 0x40000008 [13279.569230] ata4.00: failed command: READ FPDMA QUEUED [13279.569257] ata4.00: cmd 60/08:00:00:6a:05/00:00:23:00:00/40 tag 0 ncq 4096 in [13279.569262] res 41/40:00:05:6a:05/00:00:23:00:00/40 Emask 0x409 (media error) <F> [13279.569306] ata4.00: status: { DRDY ERR } [13279.569321] ata4.00: error: { UNC } [13279.575362] ata4.00: configured for UDMA/133 [13279.575388] ata4: EH complete [13283.169224] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [13283.169246] ata4.00: irq_stat 0x40000008 [13283.169263] ata4.00: failed command: READ FPDMA QUEUED [13283.169289] ata4.00: cmd 60/08:00:00:6a:05/00:00:23:00:00/40 tag 0 ncq 4096 in [13283.169294] res 41/40:00:07:6a:05/00:00:23:00:00/40 Emask 0x409 (media error) <F> [13283.169331] ata4.00: status: { DRDY ERR } [13283.169345] ata4.00: error: { UNC } [13283.176071] ata4.00: configured for UDMA/133 [13283.176104] ata4: EH complete [13286.224814] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [13286.224837] ata4.00: irq_stat 0x40000008 [13286.224853] ata4.00: failed command: READ FPDMA QUEUED [13286.224879] ata4.00: cmd 60/08:00:00:6a:05/00:00:23:00:00/40 tag 0 ncq 4096 in [13286.224884] res 41/40:00:06:6a:05/00:00:23:00:00/40 Emask 0x409 (media error) <F> [13286.224922] ata4.00: status: { DRDY ERR } [13286.224935] ata4.00: error: { UNC } [13286.231277] ata4.00: configured for UDMA/133 [13286.231303] ata4: EH complete [13288.802623] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [13288.802646] ata4.00: irq_stat 0x40000008 [13288.802662] ata4.00: failed command: READ FPDMA QUEUED [13288.802688] ata4.00: cmd 60/08:00:00:6a:05/00:00:23:00:00/40 tag 0 ncq 4096 in [13288.802693] res 41/40:00:05:6a:05/00:00:23:00:00/40 Emask 0x409 (media error) <F> [13288.802731] ata4.00: status: { DRDY ERR } [13288.802745] ata4.00: error: { UNC } [13288.808901] ata4.00: configured for UDMA/133 [13288.808927] ata4: EH complete [13291.380430] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [13291.380453] ata4.00: irq_stat 0x40000008 [13291.380470] ata4.00: failed command: READ FPDMA QUEUED [13291.380496] ata4.00: cmd 60/08:00:00:6a:05/00:00:23:00:00/40 tag 0 ncq 4096 in [13291.380501] res 41/40:00:05:6a:05/00:00:23:00:00/40 Emask 0x409 (media error) <F> [13291.380577] ata4.00: status: { DRDY ERR } [13291.380594] ata4.00: error: { UNC } [13291.386517] ata4.00: configured for UDMA/133 [13291.386543] ata4: EH complete [13294.347147] ata4.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 [13294.347169] ata4.00: irq_stat 0x40000008 [13294.347186] ata4.00: failed command: READ FPDMA QUEUED [13294.347211] ata4.00: cmd 60/08:00:00:6a:05/00:00:23:00:00/40 tag 0 ncq 4096 in [13294.347217] res 41/40:00:06:6a:05/00:00:23:00:00/40 Emask 0x409 (media error) <F> [13294.347254] ata4.00: status: { DRDY ERR } [13294.347268] ata4.00: error: { UNC } [13294.353556] ata4.00: configured for UDMA/133 [13294.353583] sd 3:0:0:0: [sdc] Unhandled sense code [13294.353590] sd 3:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [13294.353599] sd 3:0:0:0: [sdc] Sense Key : Medium Error [current] [descriptor] [13294.353610] Descriptor sense data with sense descriptors (in hex): [13294.353616] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00 [13294.353635] 23 05 6a 06 [13294.353644] sd 3:0:0:0: [sdc] Add. Sense: Unrecovered read error - auto reallocate failed [13294.353657] sd 3:0:0:0: [sdc] CDB: Read(10): 28 00 23 05 6a 00 00 00 08 00 [13294.353675] end_request: I/O error, dev sdc, sector 587557382 [13294.353726] ata4: EH complete [13294.366953] raid1:md0: read error corrected (8 sectors at 489900544 on sdc7) [13294.366992] raid1: sdc7: redirecting sector 489898496 to another mirror and they're happening quite frequently, which I guess is liable to account for the performance problem(?) # dmesg | grep mirror [12433.561822] raid1: sdc7: redirecting sector 489900464 to another mirror [12449.428933] raid1: sdb7: redirecting sector 489900504 to another mirror [12464.807016] raid1: sdb7: redirecting sector 489900512 to another mirror [12480.196222] raid1: sdb7: redirecting sector 489900520 to another mirror [12495.585413] raid1: sdb7: redirecting sector 489900528 to another mirror [12510.974424] raid1: sdb7: redirecting sector 489900536 to another mirror [12526.374933] raid1: sdb7: redirecting sector 489900544 to another mirror [12542.619938] raid1: sdc7: redirecting sector 489900608 to another mirror [12559.431328] raid1: sdc7: redirecting sector 489900616 to another mirror [12576.553866] raid1: sdc7: redirecting sector 489900624 to another mirror [12592.065265] raid1: sdc7: redirecting sector 489900632 to another mirror [12607.621121] raid1: sdc7: redirecting sector 489900640 to another mirror [12623.165856] raid1: sdc7: redirecting sector 489900648 to another mirror [12638.699474] raid1: sdc7: redirecting sector 489900656 to another mirror [12655.610881] raid1: sdc7: redirecting sector 489900664 to another mirror [12672.255617] raid1: sdc7: redirecting sector 489900672 to another mirror [12672.288746] raid1: sdc7: redirecting sector 489900680 to another mirror [12672.332376] raid1: sdc7: redirecting sector 489900688 to another mirror [12672.362935] raid1: sdc7: redirecting sector 489900696 to another mirror [12674.201177] raid1: sdc7: redirecting sector 489900704 to another mirror [12698.045050] raid1: sdc7: redirecting sector 489900712 to another mirror [12698.089309] raid1: sdc7: redirecting sector 489900720 to another mirror [12698.111999] raid1: sdc7: redirecting sector 489900728 to another mirror [12698.134006] raid1: sdc7: redirecting sector 489900736 to another mirror [12719.034376] raid1: sdc7: redirecting sector 489900744 to another mirror [12734.545775] raid1: sdc7: redirecting sector 489900752 to another mirror [12734.590014] raid1: sdc7: redirecting sector 489900760 to another mirror [12734.624050] raid1: sdc7: redirecting sector 489900768 to another mirror [12734.647308] raid1: sdc7: redirecting sector 489900776 to another mirror [12734.664657] raid1: sdc7: redirecting sector 489900784 to another mirror [12734.710642] raid1: sdc7: redirecting sector 489900792 to another mirror [12734.721919] raid1: sdc7: redirecting sector 489900800 to another mirror [12734.744732] raid1: sdc7: redirecting sector 489900808 to another mirror [12734.779330] raid1: sdc7: redirecting sector 489900816 to another mirror [12782.604564] raid1: sdb7: redirecting sector 1242934216 to another mirror [12798.264153] raid1: sdc7: redirecting sector 1242935080 to another mirror [13245.832193] raid1: sdb7: redirecting sector 489898296 to another mirror [13261.376929] raid1: sdb7: redirecting sector 489898304 to another mirror [13276.966043] raid1: sdb7: redirecting sector 489898312 to another mirror [13294.366992] raid1: sdc7: redirecting sector 489898496 to another mirror although the arrays are still running on all disks - they haven't given up on any yet: # cat /proc/mdstat Personalities : [raid1] [raid0] md10 : active raid0 md0[0] md1[1] 3368770048 blocks super 1.2 512k chunks md1 : active raid1 sde2[2] sdd2[1] 1464087824 blocks super 1.2 [2/2] [UU] md0 : active raid1 sdb7[0] sdc7[2] 1904684920 blocks super 1.2 [2/2] [UU] unused devices: <none> So I think I have some idea what the problem is but I am not a linux sysadmin expert by the remotest stretch of the imagination and would really appreciate some clue checking here with my diagnosis and what do I need to do: obviously I need to source another drive for sdc. (I'm guessing I could buy a larger drive if the price is right: I'm thinking that one day I'll need to grow the size of the array and that would be one less drive to replace with a larger one) then use mdadm to fail out the existing sdc, remove it and fit the new drive fdisk the new drive with the same size partition for the array as the old one had use mdadm to add the new drive into the array that sound OK?

  Read the article

• windows 8.1 upgrade fails with error code 0xc1900101-0x20017

  - by cmorse

  I just tried to install windows 8.1 on my laptop, but it fails to install with the message: Sorry we couldn't complete the update to Windows 8.1. We restored your previous version of Windows to this PC 0xC1900101 - 0x20017 It looks like on the first boot that the laptop is going to the PC restore screen (it asks what kind of keyboard I have, and then what repair optins I would like to take). Thus far I have just been selecting "Continue to windows 8." I'm running a Lenovo x220i tablet. I've got 43GB of free disk space. It installed just fine on my desktop. The primary difference between the two machines is that the desktop has media center install, and isn't using TrueCrypt. Full WindowsUpdate.log http://pastebin.com/hGmAW4Q1 Most important portion of WindowsUpdate.log: 2013-10-17 10:41:06:671 964 694 Agent ************* 2013-10-17 10:41:06:671 964 694 Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdates] 2013-10-17 10:41:06:671 964 694 Agent ********* 2013-10-17 10:41:06:671 964 694 Agent * Online = No; Ignore download priority = No 2013-10-17 10:41:06:671 964 694 Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1" 2013-10-17 10:41:06:671 964 694 Agent * ServiceID = {7971F918-A847-4430-9279-4A52D1EFE18D} Third party service 2013-10-17 10:41:06:671 964 694 Agent * Search Scope = {Machine & All Users} 2013-10-17 10:41:06:671 964 694 Agent * Caller SID for Applicability: S-1-5-18 2013-10-17 10:41:07:233 964 870 Report REPORT EVENT: {AD47FBDC-F7F9-4E7F-BAF4-DBA3784C7101} 2013-10-17 10:41:06:436-0600 1 202 [AU_REBOOT_COMPLETED] 102 {00000000-0000-0000-0000-000000000000} 0 0 AutomaticUpdates Success Content Install Reboot completed. 2013-10-17 10:41:07:233 964 870 Report REPORT EVENT: {8D4E7A67-9526-4702-A897-5BE5F97497AF} 2013-10-17 10:41:06:639-0600 1 204 [AGENT_INSTALLING_FAILED_POST_REBOOT] 101 {8951E70D-4332-4F7C-B92D-D9362E384959} 1 c1900101 WSAcquisition Failure Content Install Installation Failure Post Reboot. 2013-10-17 10:41:07:249 964 870 Report CWERReporter::HandleEvents - WER report upload completed with status 0x8 2013-10-17 10:41:07:249 964 870 Report WER Report sent: 7.8.9200.16715 0xc1900101(0x20017) 8951E70D-4332-4F7C-B92D-D9362E384959 Install 101 Unmanaged 2013-10-17 10:41:07:249 964 870 Report CWERReporter finishing event handling. (00000000)

  Read the article

• qemu-img: Could not open $FILE

  - by HTTP500

  I received a single-file VMDK from a vendor that has a virtual appliance for a particular product I'm interested in evaluating. We run a KVM solution (Proxmox) so I tried converting the file but on that system qemu-img blows up. (I was able to convert (multipart) VMDK files from bitnami without error.) So I figured I'll just yum install qemu-img on a RHEL 6.3 VM and do it there. But despite the fact that I can file the file just fine when I run qemu-img on it I get this error that it can't open the file: [root@host dir]# file 1.vmdk 1.vmdk: VMware4 disk image [root@host dir]# qemu-img info 1.vmdk qemu-img: Could not open 'vmdk' I've seen some other people post on the interwebs that they've had this problem but none of them seem to have a resolution. Does anyone have any ideas? I have checked the MD5SUM already. EDIT1: [root@host dir]# qemu-img info -f vmdk 1.vmdk qemu-img: Could not open '1.vmdk' EDIT2: Ran strace per suggestion. Not sure what to look for... Here is a possible: ioctl(3, CDROM_DRIVE_STATUS, 0x7fffffff) = -1 ENOTTY (Inappropriate ioctl for device)

  Read the article

• Hardware reserved memory issue

  - by Robert Koritnik

  I've seen lots of folks having problem with hardware reserved memory issue in Windows 7/Server 2008 R2. I have it myself but not as huge as others have. Problem description When you install Windows 7 (or its bigger brother Windows Server 2008 R2) your memory may not be fully utilised. If you look at Task Manager > Performance Tab > Resource Monitor > Memory Tab And scroll to the bottom of the list you will see a graphical representation of your memory. Some of it may be hardware reserved. Previous Windows versions didn't have this problem. System was able to utilise all memory available. Question Is there any solution to lower/remove hardware reserved memory? Sidenote I tried installing 32 and 64 bit versions but to no avail. I also tried both Windows: 7 and Server 2008 R2. But always get the same amount reserved by HW. On previous Windows versions I had more memory available because I'm simultaneously running 2 VMs on host (so three machines all together). And my memory peaks much higher now as it did on older versions.

  Read the article

• SSL Certifcate Request s2003 DC CA DNS Name not Avaiable.

  - by Beuy

  I am trying to submit a request for an SSL certificate on a Domain Controller in order to enable LDAP SSL, and having no end of problems. I am following the information provided at http://support.microsoft.com/default.aspx?scid=kb;en-us;321051 & http://adldap.sourceforge.net/wiki/doku.php?id=ldap_over_ssl Steps taken so far: Create Servername.inf with the following information ;----------------- request.inf ----------------- [Version] Signature="$Windows NT$ [NewRequest] Subject = "CN=servername.domain.loc" ; replace with the FQDN of the DC KeySpec = 1 KeyLength = 1024 ; Can be 1024, 2048, 4096, 8192, or 16384. ; Larger key sizes are more secure, but have ; a greater impact on performance. Exportable = TRUE MachineKeySet = TRUE SMIME = False PrivateKeyArchive = FALSE UserProtected = FALSE UseExistingKeySet = FALSE ProviderName = "Microsoft RSA SChannel Cryptographic Provider" ProviderType = 12 RequestType = PKCS10 KeyUsage = 0xa0 [EnhancedKeyUsageExtension] OID=1.3.6.1.5.5.7.3.1 ; this is for Server Authentication ;----------------------------------------------- Create Certificate request by running: certreq -new Servername.inf Servername.req Attempt to submit Certificate request to CA by running: certreq -submit -attrib "CertificateTemplate: DomainController" request.req At which point I get the following error: The DNS name is unavailable and cannot be added to the Subject Alternate Name. 0x8009480f (-2146875377) Trouble shooting steps I have taken so far 1. Modify the Domain Controller Template to supply Subject Name in Request restart Certificate Service, include SAN in Request, same error. 2. Re-installed Certificate Services / IIS / Restarted machine countless times Any help resolving the issue would be greatly appreciated.

  Read the article

• Outgrew MongoDB … now what?

  - by samsmith

  We dump debug and transaction logs into mongodb. We really like mongodb because: Blazing insert perf document oriented Ability to let the engine drop inserts when needed for performance But there is this big problem with mongodb: The index must fit in physical RAM. In practice, this limits us to 80-150gb of raw data (we currently run on a system with 16gb RAM). Sooooo, for us to have 500gb or a tb of data, we would need 50gb or 80gb of RAM. Yes, I know this is possible. We can add servers and use mongo sharding. We can buy a special server box that can take 100 or 200 gb of RAM, but this is the tail wagging the dog! We could spend boucoup $$$ on hardware to run FOSS, when SQL Server Express can handle WAY more data on WAY less hardware than Mongo (SQL Server does not meet our architectural desires, or we would use it!) We are not going to spend huge $ on hardware here, because it is necessary only because of the Mongo architecture, not because of the inherent processing/storage needs. (And sharding? Please! Cost aside, who needs the ongoing complexity of three, five, or more servers to manage a relatively small load?) Bottom line: MongoDB is FOSS, but we gotta spend $$$$$$$ on hardware to run it? We sould rather buy commercial SW! I am sure we are not the first to hit this issue, so we ask the community: Where do we go next? (We already run Mongo v2) Thanks!!

  Read the article

• Subversion gives Error 500 until authenticating with a web browser

  - by Farseeker

  We used to use Collabnet SVN/Apache combo on a Windows server with LDAP authentication, and whilst the performance wasn't brilliant it used to work perfectly. After switching to a fresh Ubuntu 10 install, and setting up an Apache/SVN/LDAP configuration, we have HTTPS access to our repositories, using Active Directory authentication via LDAP. We're now having a very peculiar issue. Whenever a new user accesses a repository, our SVN clients (we have a few depending on the tool, but for arguments sake, let's stick to Tortoise SVN) report "Error 500 - Unknown Response". To get around this, we have to log into the repo using a web browser and navigate 'backwards' until it works E.G: SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/ - Forbidden 403 (correct) Webbrowse to https://svn.example.local/SVN/MyRepo/ - OK 200 (correct) SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/MyModule/ - OK 200 (correct) SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - OK 200 (correct) It seems to require authentication up the tree, starting from the svnparentpath up through to the module required. Has anyone seen anything like this before? Any ideas on where to start before I ditch it back to Collabnet's SVN server?

  Read the article

• Automount in Ubuntu 9.10

  - by easyrider

  Hi, By default Ubuntu doesn't mount internal NTFS hard drives automatically. A fstab solution not working properly, because of conflicts with the "intelligent" mount system. If I add my hd in fstab and reboot - it will be mounted. But if I go to nautilus, open places panel and click eject button (unmount) and than click on hd again to mount it, I will get an error. In 9.04 to solve this problem you need to modify hal rules in /etc/hal/... preferences.fdi in my case I modified it for only one drive. <device> - <match key="storage.hotpluggable" bool="false"> - <match key="storage.removable" bool="false"> <merge key="storage.automount_enabled_hint" type="bool">false</merge> - <match key="storage.model" string="ST3250310NS"> <merge key="storage.automount_enabled_hint" type="bool">true</merge> </match> </match> </match> </device> But this is not working in 9.10 - devs removed this function from hal to devkit-disk or udev? I don't know. Could you please tell me where automount rules are stored in 9.10? And how to create new rules, and what program controls automount in 9.10?

  Read the article

• System Information (msinfo32.exe) Can't Collect Information

  - by ptanne

  I have Windows XP Pro, service pack 1, IE 6 and 32GB of free space, 75GB total. I have had nothing but trouble after trying to install service pack 2 even though I used System Restore. The installation was incomplete and my computer has never been the same. I attempted to install sp2 four or five times and sp3 once, always with the same result. I've tried reinstalling XP Pro but that didn't fix the problem. My XP Pro disk now has a scratch on it and refuses to work. Dell would not replace it stating that my computer was out of warranty. I'm currently trying Reimage which is supposed to return a computer to the original configuration and replace missing or damaged files. Believe it or not, Ripley, it stops in the middle of the operation and, so far, the Reimage techs haven't been able to figure out why. Of the many problems that I still have is that System Information can't collect information. The Help and Support sections that display system info also don't work. Is there some way that I can fix this? I can't afford to throw my computer away, yet. Thank you for listening, Pam Galvin

  Read the article

• How does SELinux affect the /home directory?

  - by Matt Solnit

  Hi everyone. I'm migrating a CentOS 5.3 system from MySQL to PostgreSQL. The way our machine is set up is that the biggest disk partition is mounted to /home. This is out of my control and is managed by the hosting provider. Anyway, we obviously want the database files to be on /home for this reason. With MySQL, we did the following: Edited my.cnf and changed the datadir setting to /home/mysql Added a new "File type" policy record (I hope I'm using the right terminology) to set /home/mysql(/.*)? to mysqld_db_t Ran restorecon -R /home/mysql to assign the labels and everything was good. With PostgreSQL, however, I did the following: Edited /etc/init.d/postgresql and changed the PGDATA and PGLOG variables to /home/pgsql/data and /home/pgsql/pgstartup.log, respectively Added a new policy record to set /home/pgsql/pgstartup.log to postgresql_log_t Added a new policy record to set /home/pgsql/data(/.*)? to postgresql_db_t Ran restorecon -R /home/pgsql to assign the labels At this point, I still cannot start PostgreSQL. pgstartup.log says: # cat pgstartup.log postmaster cannot access the server configuration file "/home/pgsql/data/postgresql.conf": Permission denied The weird thing is that I don't see any messages related to this in /var/log/messages or /var/log/secure, but if I turn off SElinux, then everything works. I made sure all the permissions are correct (600 for files and 700 for directories), as well as the ownership (postgres:postgres). Can anyone tell me what I am doing wrong? I'm using the Yum repository from commandprompt.com, version 8.3.7. EDIT: The reason my question specifically mentions the /home directory is that if I go through all these steps for any other directory, e.g. /var/lib/pgsql2 or /usr/local/pgsql, then it works as expected.

  Read the article

< Previous Page | 699 700 701 702 703 704 705 706 707 708 709 710  | Next Page >