Search Results

Search found 46973 results on 1879 pages for 'return path'.

Page 707/1879 | < Previous Page | 703 704 705 706 707 708 709 710 711 712 713 714  | Next Page >

• Windows for IoT, continued

  - by Valter Minute

  Originally posted on: http://geekswithblogs.net/WindowsEmbeddedCookbook/archive/2014/08/05/windows-for-iot-continued.aspxI received many interesting feedbacks on my previous blog post and I tried to find some time to do some additional tests. Bert Kleinschmidt pointed out that pins 2,3 and 10 of the Galileo are connected directly to the SOC, while pin 13, the one used for the sample sketch is controlled via an I2C I/O expander. I changed my code to use pin 2 instead of 13 (just changing the variable assignment at the beginning of the code) and latency was greatly reduced. Now each pulse lasts for 1.44ms, 44% more than the expected time, but ways better that the result we got using pin 13. I also used SetThreadPriority to increase the priority of the thread that was running the sketch to THREAD_PRIORITY_HIGHEST but that didn't change the results. When I was using the I2C-controlled pin I tried the same and the timings got ways worse (increasing more than 10 times) and so I did not commented on that part, wanting to investigate the issua a bit more in detail. It seems that increasing the priority of the application thread impacts negatively the I2C communication. I tried to use also the Linux-based implementation (using a different Galileo board since the one provided by MS seems to use a different firmware) and the results of running the sample blink sketch modified to use pin 2 and blink the led for 1ms are similar to those we got on the same board running Windows. Here the difference between expected time and measured time is worse, getting around 3.2ms instead of 1 (320% compared to 150% using Windows but far from the 100.1% we got with the 8-bit Arduino). Both systems were not under load during the test, maybe loading some applications that use part of the CPU time would make those timings even less reliable, but I think that those numbers are enough to draw some conclusions. It may not be worth running a full OS if what you need is Arduino compatibility. The Arduino UNO is probably the best Arduino you can find to perform this kind of development. The Galileo running the Linux-based stack or running Windows for IoT is targeted to be a platform for "Internet of Things" devices, whatever that means. At the moment I don't see the "I" part of IoT. We have low level interfaces (SPI, I2C, the GPIO pins) that can be used to connect sensors but the support for connectivity is limited and the amount of work required to deliver some data to the cloud (using a secure HTTP request or a message queuing system like APMQS or MQTT) is still big and the rich OS underneath seems to not provide any help doing that.Why should I use sockets and can't access all the high level connectivity features we have on "full" Windows?I know that it's possible to use some third party libraries, try to build them using the Windows For IoT SDK etc. but this means re-inventing the wheel every time and can also lead to some IP concerns if used for products meant to be closed-source. I hope that MS and Intel (and others) will focus less on the "coolness" of running (some) Arduino sketches and more on providing a better platform to people that really want to design devices that leverage internet connectivity and the cloud processing power to deliver better products and services. Providing a reliable set of connectivity services would be a great start. Providing support for .NET would be even better, leaving native code available for hardware access etc. I know that those components may require additional storage and memory etc. So making the OS componentizable (or, at least, provide a way to install additional components) would be a great way to let developers pick the parts of the system they need to develop their solution, knowing that they will integrate well together. I can understand that the Arduino and Raspberry Pi* success may have attracted the attention of marketing departments worldwide and almost any new development board those days is promoted as "XXX response to Arduino" or "YYYY alternative to Raspberry Pi", but this is misleading and prevents companies from focusing on how to deliver good products and how to integrate "IoT" features with their existing offer to provide, at the end, a better product or service to their customers. Marketing is important, but can't decide the key features of a product (the OS) that is going to be used to develop full products for end customers integrating it with hardware and application software. I really like the "hackable" nature of open-source devices and like to see that companies are getting more and more open in releasing information, providing "hackable" devices and supporting developers with documentation, good samples etc. On the other side being able to run a sketch designed for an 8 bit microcontroller on a full-featured application processor may sound cool and an easy upgrade path for people that just experimented with sensors etc. on Arduino but it's not, in my humble opinion, the main path to follow for people who want to deliver real products.   *Shameless self-promotion: if you are looking for a good book in Italian about the Raspberry Pi , try mine: http://www.amazon.it/Raspberry-Pi-alluso-Digital-LifeStyle-ebook/dp/B00GYY3OKO

  Read the article

• Installing 64bit Java 7 - Cannot Execute Binary File

  - by warpstack

  So I downloaded the latest version of Java from Oracle so I could get a 64bit JVM on Ubuntu Server 10.10. After extracting the file and updating the alternatives I went to check my installation by running java -version and I get this error: -bash: /usr/bin/java: cannot execute binary file I'm at a loss for what to do here. My alternatives menu looks like this: Selection Path Priority Status ------------------------------------------------------------ 0 /usr/lib/jvm/java-6-openjdk/jre/bin/java 1061 auto mode 1 /usr/lib/jvm/java-6-openjdk/jre/bin/java 1061 manual mode 2 /usr/lib/jvm/java-7-openjdk-i386/jre/bin/java 1051 manual mode * 3 /usr/lib/jvm/jdk1.7.0/bin/java 3 manual mode After restarting the system I seem to be getting a totally new error when checking the java version. usr/bin/java: 1: Syntax error: end of file unexpected (expecting ")")

  Read the article

• Acer Aspire installation of Ubuntu as the one and only OS

  - by Anthalis

  I am quite sick of a Win7 limited edition that was pre-installed on my Acer Aspire One 533. I want to have Ubuntu as the only OS on this little thing. I have tested Ubuntu on a pretty unstable system and I am simply in love with it, despite the fact that I am still on the learning path. So my questions is how do I format/erase all previous info, including windows files? I am interested in a real cleanup of the drives rather than just a re-partitioning, because I travel every now and then and I want to prevent any personal data remaining on the drives for anyone with recovery knowledge to sniff through. Thanks in advance for your input and advice. A.

  Read the article

• Need instructions how to create wpa_supplicant.conf and add fast_reauth=0 to it // WPA 2 Enterprise & frequent wlan disconnects

  - by nutty about natty

  Like many other natty users on a university / academic network, I'm experiencing annoying frequent disconnects / hangs / delays. See, for instance: https://bugs.launchpad.net/ubuntu/+source/wpasupplicant/+bug/429370 I would like to learn how to add fast_reauth=0 to the wpa_supplicant.conf file. This file, it seems, does not exit by default, and needs to be manually created first: http://w1.fi/gitweb/gitweb.cgi?p=hostap.git;a=blob_plain;f=wpa_supplicant/README [quote] You will need to make a configuration file, e.g., /etc/wpa_supplicant.conf, with network configuration for the networks you are going to use. [unquote] Further, I installed wpa_gui which probably needs to be launched with parameters, else it's pretty blank... What I'm hoping for is this: That creating a wpa_supplicant.conf file with fast_reauth=0 in it, saving it to the relevant path, will work and make my uni wireless (more or even completely) stable. I read mixed reviews about wicd (as an alternative to the network manager). Also note that on my basic wlan at home (with bog-standard wpa encryption) the connection is stable. Thanks!

  Read the article

• Inconsistencies in Health Monitoring Between WebForms and MVC

  As I have written and spoken on numerous occasions, Health Monitoring happens to be one of my favorite features in ASP.NET. In WebForms, it's a path well trodden. However, while building Morts & Elvises with MVC2, I ran into a strange inconsistency, which I'd like to describe here. WebForms Whenever a WebForm throws an unhandled exception, at the very least the error is written to the system's even log. Suppose we have this silly simple page method: protected override void OnLoad...Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• How do I get write access to ubuntu files from Windows?

  - by Steven

  I'm running Ubuntu 11.10 on my Virtual Machine as a web server. I've mounted the W:/ drive in Win 7 to my /www folder in Ubuntu. I can read the files, but I'm not able to write to the files. In Samba, I have created the following user: <www-data> = "<www-data>" And given guest ok for the www folder: [www] comment = Ubuntu WWW area path = /var/www browsable = yes guest ok = yes read only = no create mask = 0755 ;directory mask = 0775 force user = www-data force group = www-data I've also run sudo chmod -R 755 www to make ensure correct rw access. What am I missing in order to get write access to my ubuntu files from Windows?

  Read the article

• Problems, connecting Android ICS to Ubuntu using MTP

  - by ubuntico

  I've followed this tutorial from this blog which very clearly explains how to connect Android phone with ICS to Ubuntu so that one can access phone's sdcard (MTP access). I passed all the procedure with no errors, I can event attach my mobile to ubuntu via mtpfs -o allow_other ~/Android/GalaxyS2 and disconnect via fusermount -u ~/Android/GalaxyS2 The problem comes when I try to access mounted directory. If I try to do it via Nautilus, the system tries to open the folder for a couple of minutes and then, I either see the error, or the folder disappears from Nautilus (it comes back when I disconnect the path). I also get a console error: fuse: bad mount point `~/Android/GalaxyS2': Transport endpoint is not connected I see many people on the net reporting this error, but noone offers any solution to it. I use Ubuntu 11.10 with Gnome Shell (Gnome 3) and the mobile is Samsung Galaxy S II. I am in the fuse list, I did all the steps in the tutorial for dozens of times, all in vain.

  Read the article

• How can I share my python scripts with my less python-savvy business person partner?

  - by Alex

  I'm taking financial mathematics as an elective, and I'm working with real life finance industry worker type people. It's actually kind of fun. When I pulled out a macbook at one of our meetings, I had four lifelong windows users look at me like I had three heads. Anyway, I'm helping with design and simulation of our trading strategy, and I wrote a little thing using matplotlib to visualize historical stock data. However, these guys don't know how to use git, or install python, or deal with path-related package management things. I need to be able to send my scripts to them to use, and I need to do it with absolutely minimal effort on their part. I was thinking something on the lines of py2exe, but I'd like to hear some advice before I go ahead.

  Read the article

• Software developer needs Validation for VA Chap 31 to purchase Macbook Pro vs. PC [closed]

  - by David

  I am currently attending college with a path of software development and working towards my BS thanks to VA Chap 31. My old original Macbook Pro is near dead and no longer upgradable on the software or hardware side. The VA has offered to purchase a PC laptop for me (Because my syllabi says computer required), but I do not want to go backwards. I have a lot invested in OS X software and Mac peripherals, not to mention I prefer to program in an Apple environment. PC vs. Mac costs are so drastically different that I must validate my request for a new Macbook Pro. In my request to the VA, I stated the above and some other topics but they requested more validation. Can anyone recommend issues, reasons, etc. to help me validate this purchase by the VA for school? Thanks in advance for your help, David

  Read the article

• Windows: How to make programs think they're not running in a terminal server session?

  - by sinni800

  I am using the program "SoftXPand 2011 Duo" by Miniframe on my Windows 7 PC. It makes two workstations out of one computer. It uses the terminal services built into Windows to create the additional session. I use two screens, two keyboards and two mice to create this "illusion" of two computers. It works quite well and I can even play two different 3D games on the two screens attached to this single machine (using a Radeon HD5770 and a Core i5 2500k with 8 Gbytes RAM). There are a few downsides to this. I just found about one that is hidden on the first look. The sessions you are in (even on the first workstation) will identify as a terminal server session! Now some programs will run with limited effects (graphical), and some won't run at all. This also resulted in some games not running at all. They just say "Cannot be run in a terminal server session" and exit. I have already proven that top modern games (DirectX 10, 11) run just as good as on the same machine without SoftXPand, so this is a pretty artificial limitation! So, can I somehow hack my current session so it doesn't look like a terminal server session anymore? I. E. #include <windows.h> #pragma comment(lib, "user32.lib") BOOL IsRemoteSession(void) { return GetSystemMetrics( SM_REMOTESESSION ); } Will return FALSE? (Not a programming question! Just an example how programs detect if they're in a terminal server session!)

  Read the article

• C#/.NET Little Wonders: Getting Caller Information

  - by James Michael Hare

  Originally posted on: http://geekswithblogs.net/BlackRabbitCoder/archive/2013/07/25/c.net-little-wonders-getting-caller-information.aspx Once again, in this series of posts I look at the parts of the .NET Framework that may seem trivial, but can help improve your code by making it easier to write and maintain. The index of all my past little wonders posts can be found here. There are times when it is desirable to know who called the method or property you are currently executing.  Some applications of this could include logging libraries, or possibly even something more advanced that may server up different objects depending on who called the method. In the past, we mostly relied on the System.Diagnostics namespace and its classes such as StackTrace and StackFrame to see who our caller was, but now in C# 5, we can also get much of this data at compile-time. Determining the caller using the stack One of the ways of doing this is to examine the call stack.  The classes that allow you to examine the call stack have been around for a long time and can give you a very deep view of the calling chain all the way back to the beginning for the thread that has called you. You can get caller information by either instantiating the StackTrace class (which will give you the complete stack trace, much like you see when an exception is generated), or by using StackFrame which gets a single frame of the stack trace.  Both involve examining the call stack, which is a non-trivial task, so care should be done not to do this in a performance-intensive situation. For our simple example let's say we are going to recreate the wheel and construct our own logging framework.  Perhaps we wish to create a simple method Log which will log the string-ified form of an object and some information about the caller.  We could easily do this as follows: 1: static void Log(object message) 2: { 3: // frame 1, true for source info 4: StackFrame frame = new StackFrame(1, true); 5: var method = frame.GetMethod(); 6: var fileName = frame.GetFileName(); 7: var lineNumber = frame.GetFileLineNumber(); 8: 9: // we'll just use a simple Console write for now 10: Console.WriteLine("{0}({1}):{2} - {3}", 11: fileName, lineNumber, method.Name, message); 12: } So, what we are doing here is grabbing the 2nd stack frame (the 1st is our current method) using a 2nd argument of true to specify we want source information (if available) and then taking the information from the frame.  This works fine, and if we tested it out by calling from a file such as this: 1: // File c:\projects\test\CallerInfo\CallerInfo.cs 2:  3: public class CallerInfo 4: { 5: Log("Hello Logger!"); 6: } We'd see this: 1: c:\projects\test\CallerInfo\CallerInfo.cs(5):Main - Hello Logger! This works well, and in fact CallStack and StackFrame are still the best ways to examine deeper into the call stack.  But if you only want to get information on the caller of your method, there is another option… Determining the caller at compile-time In C# 5 (.NET 4.5) they added some attributes that can be supplied to optional parameters on a method to receive caller information.  These attributes can only be applied to methods with optional parameters with explicit defaults.  Then, as the compiler determines who is calling your method with these attributes, it will fill in the values at compile-time. These are the currently supported attributes available in the  System.Runtime.CompilerServices namespace": CallerFilePathAttribute – The path and name of the file that is calling your method. CallerLineNumberAttribute – The line number in the file where your method is being called. CallerMemberName – The member that is calling your method. So let’s take a look at how our Log method would look using these attributes instead: 1: static int Log(object message, 2: [CallerMemberName] string memberName = "", 3: [CallerFilePath] string fileName = "", 4: [CallerLineNumber] int lineNumber = 0) 5: { 6: // we'll just use a simple Console write for now 7: Console.WriteLine("{0}({1}):{2} - {3}", 8: fileName, lineNumber, memberName, message); 9: } Again, calling this from our sample Main would give us the same result: 1: c:\projects\test\CallerInfo\CallerInfo.cs(5):Main - Hello Logger! However, though this seems the same, there are a few key differences. First of all, there are only 3 supported attributes (at this time) that give you the file path, line number, and calling member.  Thus, it does not give you as rich of detail as a StackFrame (which can give you the calling type as well and deeper frames, for example).  Also, these are supported through optional parameters, which means we could call our new Log method like this: 1: // They're defaults, why not fill 'em in 2: Log("My message.", "Some member", "Some file", -13); In addition, since these attributes require optional parameters, they cannot be used in properties, only in methods. These caveats aside, they do let you get similar information inside of methods at a much greater speed!  How much greater?  Well lets crank through 1,000,000 iterations of each.  instead of logging to console, I’ll return the formatted string length of each.  Doing this, we get: 1: Time for 1,000,000 iterations with StackTrace: 5096 ms 2: Time for 1,000,000 iterations with Attributes: 196 ms So you see, using the attributes is much, much faster!  Nearly 25x faster in fact.  Summary There are a few ways to get caller information for a method.  The StackFrame allows you to get a comprehensive set of information spanning the whole call stack, but at a heavier cost.  On the other hand, the attributes allow you to quickly get at caller information baked in at compile-time, but to do so you need to create optional parameters in your methods to support it. Technorati Tags: Little Wonders,CSharp,C#,.NET,StackFrame,CallStack,CallerFilePathAttribute,CallerLineNumberAttribute,CallerMemberName

  Read the article

• Why is using C++ libraries is so complicated?

  - by Pius

  First of all, I want to note I love C++ and I'm one of those people who thinks it is easier to code in C++ than Java. Except for one tiny thing: libraries. In Java you can simply add some jar to the build path and you're done. In C++ you usually have to set multiple paths for the header files and the library itself. In some cases, you even have to use special build flags. I have mainly used Visual Studio, Code Blocks and no IDE at all. All 3 options do not differ much when talking about using external libraries. I wonder why was there made no simpler alternative for this? Like having a special .zip file that has everything you need in one place so the IDE can do all the work for you setting up the build flags. Is there any technical barrier for this?

  Read the article

• Goal completions 10x higher in dashboard

  - by cjk

  I have the following table in my Dashboard: Page path level 1 Visits Goal Completions ----------------- ------ ---------------- /sub1/ 994 1,295 / 102 3 /sub2/ 10 1 I know my conversion rate is 10-20%, and that actually in this period I only had 183 goal completions under /sub1/. My goal is set as a regular expression for a particular page (/success?.*), and I have a funnel set up which tracks the page before the goal (/action). The actual urls hit would be /sub1/action then /sub1/success?1234 and /sub2/action then /sub2/success?1234. Why is my table in my dashboard giving me wildly wrong numbers? Have I done something wrong?

  Read the article

• EFS Remote Encryption

  - by Apoulet

  We have been trying to setup EFS across our domain. Unfortunately Reading/Writing file over network share does not work, we get an "Access Denied" error. Another worrying fact is that I managed to get it working for 1 machine but no other would work. The machines are all Windows 2008R2, running as VM under ESXi host. According to: http://technet.microsoft.com/en-us/library/bb457116.aspx#EHAA We setup the involved machine to be trusted for delegation The user are not restricted and can be trusted for delegation. The users have logged-in on both side and can read/write encrypted files without issues locally. I enabled Kerberos logging in the registry and this is the relevant logs that I get on the machine that has the encrypted files. In order for all certificate that the user possess (Only Key Name changes): Event ID 5058: Audit Success, "Other System Events" Key file operation. Subject: Security ID: {MyDOMAIN}\{MyID} Account Name: {MyID} Account Domain: {MyDOMAIN} Logon ID: 0xbXXXXXXX Cryptographic Parameters: Provider Name: Microsoft Software Key Storage Provider Algorithm Name: Not Available. Key Name: {CE885431-9B4F-47C2-8415-2D766B999999} Key Type: User key. Key File Operation Information: File Path: C:\Users\{MyID}\AppData\Roaming\Microsoft\Crypto\RSA\S-1-5-21-4585646465656-260371901-2912106767-1207\66099999999991e891f187e791277da03d_dfe9ecd8-31c4-4b0f-9b57-6fd3cab90760 Operation: Read persisted key from file. Return Code: 0x0[/code] Event ID 5061: Audit Faillure, "System Intergrity" [code]Cryptographic operation. Subject: Security ID: {MyDOMAIN}\{MyID} Account Name: {MyID} Account Domain: {MyDOMAIN} Logon ID: 0xbXXXXXXX Cryptographic Parameters: Provider Name: Microsoft Software Key Storage Provider Algorithm Name: RSA Key Name: {CE885431-9B4F-47C2-8415-2D766B999999} Key Type: User key. Cryptographic Operation: Operation: Open Key. Return Code: 0x8009000b Could this be related to this error from the CryptAcquireContext function NTE_BAD_KEY_STATE 0x8009000BL The user password has changed since the private keys were encrypted. The problem is that the users I using at the moment can not change their password.

  Read the article

• 2d Ice movement

  - by Jeremy Clarkson

  I am building an top-down 2d RPG like zelda. I have been trying to implement ice sliding. I have a tile with the slide property. I thought it would be easy to get working. I figured that I would read the slide property, and move the character forward until the slide property no longer exists. So I tried a loop but all it did was stop at the first tile in an infinite loop. I then took the loop out and tried taking direct control of the character to move him along the slide path but I couldn't get it to move. Is there an easy way to do an ice sliding tile based movement in libgdx. I looked for a tutorial but none exist.

  Read the article

• Designing an API on top with Java RMI and Rest APIs

  - by user1303881

  I'm working on the backend of a java web application. We have a document repository (Fedora Commons specifically) where we house xml files. I want to abstract the API of the repository internally so that we aren't tightly coupled to one product. I'd also like to give the flexibility of connecting to to a repository via Java RMI or REST APIs. I was hoping to get advice or resources on how to implement something like this. My thought it that I'd have some abstract repository class that had methods like getRecord, updateRecord, and deleteRecord. In the constructor I would pass the URI for the repository and the API method and port. This would allow some flexibility in the future so that if the REST api became more practical, but allow the flexibility or using RMI which could (should?) have better performance. Am I over thinking this or am I on the right path?

  Read the article

• VS2010 crashes when opening a vsp generated using VS 2012

  - by Tarun Arora

  I recently profiled some web applications using Visual Studio 2012, a vsp (Visual Studio Profile) file was generated as a result of the profiling session. I could successfully open the vsp file in Visual Studio 2012 as expected but when I tried to open the vsp file in Visual Studio 2010 the VS2010 IDE crashed. As a responsible citizen I raised bug # 762202 on Microsoft Connect site using the Microsoft Visual Studio 2012 Feedback Client. Note – In case you didn’t already know, VSP generated in Visual Studio 2012 is not backward compatible. Please refer below for the steps to reproduce the issue and the resolution of the connect bug. 1. Behaviour and Steps to Reproduce the Issue Description I have generated a vsp file by using the Visual Studio 2012 Standalone profiler. When I try and open the vsp file in Visual Studio 2010 the IDE crashes. I understand that a vsp generated by using VS 2012 cannot be opened in VS 2010, but the IDE crashing is not the behaviour I would expect to see. Steps to Reproduce the Issue 1. Pick up the Stand lone profiler from the VS 2012 installation media. The folder has both x 64 and x86 installer, since the machine I am using is x64 bit. I have installed the x64 version of the standalone profiler. 2. I have configured the system path by setting the 'environment variable' path to where the profiler is installed. In my case this is, C:\Program Files (x86)\Microsoft Visual Studio 11.0\Team Tools\Performance Tools 3. Created a new environment variable _NT_SYMBOL_PATH and set its value to CACHE*C:\SYMBOLSCACHE;SRV*C:\SYMBOLSCACHE*HTTP://MSDL.MICROSOFT.COM/DOWNLOAD/SYMBOLS;\\FOO\BUILD1234 4. Open up CMD as an administrator and run 'VSPerfASPNETCmd /tip http://localhost:56180/ /o:C:\Temp\SampleEISK.vsp' 5. This generates the following message on the cmd       Microsoft (R) VSPerf ASP.NET Command, Version 11.0.0.0     Copyright (C) Microsoft Corporation. All rights reserved.     Configuring and attaching to ASP.NET process. Please wait.     Setting up profiling environment.     Starting monitor.     Launching ASP.NET service.     Attaching Monitor to process.     Launching Internet Explorer.     The profiler is attached to ASP.net. Please run your application scenario now.     Press Enter to stop data collection...   6. I perform certain actions and then I come back to the cmd and hit enter to shut down the profiling. Once I do this, the following message is written to the cmd, Press Enter to stop data collection... Profiling now shut down. Report file "C:\Temp\SampleEISK.vsp" was generated. Running VsPerfReport, packing symbols into the .VSP. Shutting down profiling and restarting ASP.NET. Please wait. Restarting w3wp.exe.   7. I look in the C:\Temp folder and I can see the SampleEISK.vsp file generated. I can successfully open this file in Visual Studio 2012. 8. When I am trying to open the vsp file in VS 2010 the VS 2010 IDE crashes. Kaboooom! What I would expect to happen I expect to receive a message "VS 2010 does not support the vsp file generated by VS 2012". What actually happened The VS 2010 IDE crashed 2. Resolution This is a valid bug! However, there isn’t much value in releasing a hotfix for this issue. Refer below to the resolution provided by the Visual Studio Profiler Team.  Thank you for taking the time to report this issue. We completely agree that Visual Studio 2010 should not crash. However in this particular case this is not a bug we are going to retroactively release a fix to 2010 for at this point. Given that a fix would not unblock the scenario of opening a 2012 created file on Visual Studio 2010, and there is not an active update channel for Visual Studio 2010 other than manually locating and installing hot fixes, we will not be fixing this particular issue. Best Regards, Visual Studio Profiler Team   Though it would be great to improve the behaviour however, this is not a defect that would stop you from progressing in any way. It’s important to note however that VSP files generated by Visual Studio 2012 are not backward compatible so you should refrain from opening these files in Visual Studio 2010.

  Read the article

• Forward .html/.htm to .php with .config

  - by PhilipK

  I'm moving a site from my linux hosted server to a client's windows hosted server. The .htaccess file no longer works and I'm told that windows servers use .config . How can I forward all users accessing .html & .htm files to the equivalent .php file. Server Info... OS/Hosting Type: Windows / Shared Hosting .Net Runtime Version: ASP.Net 2.0/3.0/3.5 PHP Version: PHP 5.2 IIS Version: IIS 7.0 Data Center: US Regional EDIT *Hosting provided by GoDaddy Was told by a friend following should work but it has no effect on the site. <configuration> <system.webServer> <handlers> <add name="PHP-FastCGI" verb="*" path="*.html" modules="FastCgiModule" scriptProcessor="c:\php\php-cgi.exe" resourceType="Either" /> </handlers> </system.webServer> </configuration>

  Read the article

• Can not start webhttrack

  - by Sitati

  I am trying to start my webhttrack on ubuntu 12.04 precise pangolin but all i get is the opening screen. When i press any button on the page it gives me the following errors: Oops! Google Chrome could not connect to barney:8081 Suggestions: Try reloading: barney:­8081/­server/­step2.­html i tried to run from a terminal window and get the output here: webhttrack /usr/bin/webhttrack(4405:( launching /usr/bin/x-www-browser /usr/bin/webhttrack(4405:( spawning regular browser.. Created new window in existing browser session. /usr/bin/webhttrack(4405:( browser exited /usr/bin/webhttrack: line 167: 4422 Killed ${BINPATH}/htsserver "${DISTPATH}/" path "${HOME}/websites" lang "${LANGN}" $@ If anyone can help me i appreciate it.

  Read the article

• Explicit resource loading in Ogre (Mogre)

  - by sebf

  I am just starting to learn Mogre and what I would like to do is to be able to load resources 'explicitly' (i.e. I just provide an absolute path instead of using a resource group tied to a directory). This is very different to manually loading resources, which I believe in Ogre has a very specific meaning, to build up the object using Ogres methods. I want to use Ogres resource management system/resource loading code, but to have finer control over which files are loaded and in what groups they are. I remember reading how to do this but cannot find the page again; I think its possible to do something like: Declare a resource group Declare the resource(s) (this is when the actual resource file name is provided) Initialise the resource group to actually load the resource(s) Is this the correct procedure? If so, is there any example code showing how to do this?

  Read the article

• iptables captive portal remove user

  - by Burgos

  I followed this guide: http://aryo.info/labs/captive-portal-using-php-and-iptables.html I am implementing captive portal using iptables. I've setup web server and iptables on linux router, and everything is working as it should. I can allow user to access internet with sudo iptables -I internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN and I can remove access with sudo iptables -D internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN However, on removal, user can still open last viewed page as many times he wants (if he restart his Ethernet adapter, future connections will be closed). On blog page I found a script /usr/sbin/conntrack -L \ |grep $1 \ |grep ESTAB \ |grep 'dport=80' \ |awk \ "{ system(\"conntrack -D --orig-src $1 --orig-dst \" \ substr(\$6,5) \" -p tcp --orig-port-src \" substr(\$7,7) \" \ --orig-port-dst 80\"); }" Which should remove their "redirection" connection track, as it is written, but when I execute that script, nothing happens - user still have access to that page. When I execute /usr/sbin/conntrack -L | grep USER_IP after executing script I am having nothing returned, so my questions: Is there anything else that can help me clean these track? Obviously - I can't reset nor mine, nor users network adapter.

  Read the article

• The Journey to the Mystical Forest [Wallpaper]

  - by Asian Angel

  MYSTICAL FOREST PATH [DesktopNexus] Latest Features How-To Geek ETC Macs Don’t Make You Creative! So Why Do Artists Really Love Apple? MacX DVD Ripper Pro is Free for How-To Geek Readers (Time Limited!) HTG Explains: What’s a Solid State Drive and What Do I Need to Know? How to Get Amazing Color from Photos in Photoshop, GIMP, and Paint.NET Learn To Adjust Contrast Like a Pro in Photoshop, GIMP, and Paint.NET Have You Ever Wondered How Your Operating System Got Its Name? Sync Blocker Stops iTunes from Automatically Syncing The Journey to the Mystical Forest [Wallpaper] Trace Your Browser’s Roots on the Browser Family Tree [Infographic] Save Files Directly from Your Browser to the Cloud in Chrome and Iron The Steve Jobs Chronicles – Charlie and the Apple Factory [Video] Google Chrome Updates; Faster, Cleaner Menus, Encrypted Password Syncing, and More

  Read the article

• Oracle will be a Bronze Sponsor of Grace Hopper Celebration of Women in Cmputing

  - by bubbva

  Oracle is proud to be a Bronze Sponsor at the upcoming Grace Hopper Celebration of Women in Computing from October 3-6, 2012 in Baltimore, MD. Oracle's Women's Leadership group, Oracle's Diversity & Inclusion program and Product Development are proud to be behind this sponsorship.Several women from Oracle will be presenting and participating at the conference: Industry Track: "From Engineer to Executive; The Path Forward", speaker Susan Zwinger VP, Global Systems Technology Service Center Industry Track: "Are We There Yet? Finding Your Career Sweet Spot", speaker Gilda Garreton, Principal Software Engineer Birds of a feather:  "Juggling Our Different Worlds", speaker Gilda Garreton New Investigator Co-Chair, Gilda Garreton Communities Committee Co-Chair, Valerie Fenwick, Manager Software Development "Considering a shift in career from Technical towards Management?" table host,  Valerie Fenwick Oracle will have a booth as well, so stop by and introduce yourself!

  Read the article

• java MainServer gives java.lang.UnsupportedClassVersionError: Unsupported major.minor version 51.0

  - by Paradox

  Compiling is easy but when using java to run the programs, it gives Exception found. I am using Ubuntu 12.04 without internet connections. Also, installed Oracle JDK7 and JRE7. Also did the update-alternatives command on java, javac and javaws. Changed the machine java in /etc/profiles. PATH is pointing to oracle java folder. I did many searches on Google about this topic but each time jdk and jre version are different. Also check version of jdk and jre using java -version and javac - version. Both of them are the same. The system also contains OpenJdk6 and OpenJdk7. So, how do I remove these errors?

  Read the article

• Unable to locate package lightread

  - by TENG PENG

  I have changed my source to local server. I'm using Ubuntu 12.10. When I type apt-cache search in terminal, it shows nothing. When I install lightread it shows Unable to locate package lightread. When I install lightread manually by python. It shows python '/home/peng/Downloads/quickly_trunk/setup.py' Traceback (most recent call last): File "/home/peng/Downloads/quickly_trunk/setup.py", line 93, in <module> data_files=[('share/icons/hicolor/128x128/apps', ['data/media/lightread.png'])] File "/usr/lib/python2.7/dist-packages/DistUtilsExtra/auto.py", line 71, in setup src_mark(src, 'setup.py') File "/usr/lib/python2.7/dist-packages/DistUtilsExtra/auto.py", line 527, in src_mark src.remove(path) KeyError: 'setup.py' How to solve the problem?

  Read the article

< Previous Page | 703 704 705 706 707 708 709 710 711 712 713 714  | Next Page >