Search Results

Search found 42786 results on 1712 pages for 'install from source'.

Page 713/1712 | < Previous Page | 709 710 711 712 713 714 715 716 717 718 719 720  | Next Page >

• Dual-booting Ubuntu and Pardus with GRUB2...Pardus no show?

  - by Ibn Ali al-Turki

  I have Ubuntu 10.10 installed and used to dual-boot Fedora, but I replaced Fedora with Pardus. After the install, I went into ubuntu, and did a sudo update-grub. It detected my Pardus 2011 install there. When I rebooted, it did not show up in my grub2 menu however. I went back to Ubuntu and did it again...then checked the grub.cfg, and it is not there. I have read that Pardus uses a grub legacy. How can I get Pardus into my grub2 menu? Thanks! sudo fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd9b3496e Device Boot Start End Blocks Id System /dev/sda1 * 1 15197 122067968 83 Linux /dev/sda2 36394 60802 196059757 5 Extended /dev/sda3 15197 30394 122067968 83 Linux /dev/sda5 36394 59434 185075308 7 HPFS/NTFS /dev/sda6 59434 60802 10983424 82 Linux swap / Solaris Partition table entries are not in disk order and update-grub Found linux image: /boot/vmlinuz-2.6.35-25-generic Found initrd image: /boot/initrd.img-2.6.35-25-generic Found memtest86+ image: /boot/memtest86+.bin Found Pardus 2011 (2011) on /dev/sda3 Yet after this, I go to grub.cfg, and Pardus is not there.

  Read the article

• sata hard drive failed

  - by M. Shehryar

  Dear friend, initially my dual core PC started shutdown and re-start by itself after adding 1 GB ram and up-grading the graphic card. Then refused to boot. I restored the window ghost but failed to boot. I tried to install new window but installation failed after coping the window files. tried to install old vista lonhorn. It inspected found errors, fixed them but ultimatly failed to be installed. Once again restored the ghost through acronis but failed to boot. At the end attached as slave with another pc but it was not visible. Even acronis could not see it or its partitions. Only bios can see it. It seems that no file system is available on the drive. My data on drive is very important. Please help me how to revover my data. Drive brand is Samsung, cap is 160 GB and file system was NTFS.

  Read the article

• mac gets stuck in a blue screen during boot

  - by user10826

  Hi, a macbook pro 2008 unibody, after restart gets stuck in a blue screen. I used the Leopard disk and I verified and repaired permissions, which seem to be a problem, because the assistant found some wrong files. After restart I got the same problem. After googling I reset PRAM and the other (I do not remember the name now). Same problem. I check that I can boot in safe mode, although it is a lot slower. So before anything I try to make a time machine backup, hoping that I can be done from safe mode. First question: If it works, is it possible to do a clean leopard install (I do not like Snow) and migrate all user accounts from the backup, although it was done in safe mode? Second question: I read about the feature "archive and install" from the leopard disc. Is it reliable? Because I am afraid of losing all data ... Third question: I think this boot stuck has to do with the load of some program or service. It would explain why the computer does boot on safe mode and not in the normal one. I would then like to check what the computer loads during boot, but in more detail that with the information provided from /system preferecens/account/start, because there I removed everything. Where can I find more advanced information? And, if I remove programs from the safe mode, will it be effective druing the normal boot? Thanks

  Read the article

• Blink build with Xcode failed

  - by Merci

  I found a GPL-ed SIP client for Mac, Blink. I'd like to build it from source since the binaries are only available as paid download. Just FYI i'm studying programming at university but have no experience in building complex application from source. After downloading the content of the repository i opened the Xcode project and tried to build on OS X 10.7, Xcode 4.2.1. Unfortunately the build fail with 1 error and many warnings Most of the warnings are like this: Attribute Unavailable: Custom Identifiers in Interface Builder versions prior to 3.2 The error message is: Apple Mach-O Linker (ld) Error Command /Developer/usr/bin/clang failed with exit code 1 preceded by the warning Apple Mach-O Linker (ld) Warning directory not found for option '-L/Users/Sergio/Downloads/Blink/devel.ag-projects.com/repositories/public/blink-cocoa/Distribution/Frameworks' I notice that in the list of required files i have this files missing: Dependencies/Frameworks libgcrypt.11.6.0.dylib libgcrypt.11.dylib libgnutls-extra.26.dylib libgnutls.26.dylib libgpg-error.0.dylib libintl.8.dylib liblzo.1.dylib libtasn1.3.dylib Dependencies/Resources lib Frameworks/Linked Frameworks Sparkle.framework Products Blink.app It should be possible to download these files somewhere. Unfortunately googling did not help. There's no documentation on the project site.

  Read the article

• Installing ffmpeg + dependencies on AWS Linux AMI (repo issues)

  - by HdN8

  I'm installing ffmpeg to run on an Amazon linux AMI, and have added the rpmforge repo and the dag repo. Here are some guidelines I'm using for reference: TWoZaO and Razuna The rpmforge repo has ffmpeg, but if you try to install it then it will complain that is missing dependencies (for me libSDL-1.2.so.0()(64bit)). Regardless I will install ffmpeg from svn so I can be sure to enable the options I want (namelylibx264). It seems strange to me though that SDL is not inrpmforgeordag`, and in according to both of my references above, it should be there. I tried to grab it manually from here, but it needs these dependencies, so no-go: > error: Failed dependencies: SDL = > 1.2.10-8.el5 is needed by SDL-devel-1.2.10-8.el5.x86_64 > alsa-lib-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libGL-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libGLU-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libSDL-1.2.so.0()(64bit) is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libX11-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXext-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXrandr-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXrender-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXt-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64

  Read the article

• trouble shooting ntfs-loop-xen combination in wubi based grub of Ubuntu

  - by Registered User

  Here is a situation I installed Ubuntu on a laptop using Wubi in Windows 7 drive.*The laptop is not mine.*I have installed and things worked by now perfectly without any problem.We are trying to set up a Xen (virtualization)environment in this laptop. After setting up every thing cleanly.When I needed to boot with following grub entries menuentry "Xen Linux 2.6.32.27" { insmod ntfs set root='(hd0,2)' loopback loop0 /ubuntu/disks/root.disk set root=(loop0) multiboot /boot/xen.gz module /boot/vmlinuz-2.6.32.27 dummy=dummy root=/dev/sda2 loop=/ubuntu/disks/root.disk ro console=tty0 module /boot/initrd.img-2.6.32.27 } I got error file not found error unknown command 'multiboot' error unknown command 'module' error unknown command 'module' Now to dig this issue further I reboot the machine and go to grub command prompt and manually pass on each of the above parameters which you see in the grub entry when I reached grub> insmod multiboot then I got following message on screen error:file not found. It looks like this wubi+ grub setup has just enough modules to use loopback file on ntfs, but the ACTUAL /boot directory is on the loopback NOT ntfs (hd0,2). Therefore any attempt to read any files from (hd0,2) simply wont work, cause there's no file there.I need to use insmod multiboot and command multiboot and module which are available in grub on a normal install without Wubi.But since the laptop is not mine so I am not allowed to partition it and have to make it work in this situation only. While a normal Kernel is still booting? How can I get module multiboot in this Wubi based install.

  Read the article

• Windows 7 64bit will not register a 32bit DLL

  - by Bad Neighbor

  I'm trying to install a 32bit Oracle instant client onto several Windows 7 PCs. This version is the one required by the customer's software. I have successfully installed it on about a dozen PCs using the same installer, but two machines refuse to register a DLL. The two PCs are of different make and model. I have been able to install this software in the past on these models. This is the error that the installer throws up: The file copies to the location referenced above. If I choose to ignore the error and manually register it later, I get the following error: This error is returned whether I use the 32bit (syswow64) or 64bit version of regsvr32. Command Prompt is run as admin, and the ID with which I'm logged into the PC is an admin. I've tried copying the file into the syswow64 folder, but I get the same error. This same installer works on other PCs. To further complicate the issue, one of the two PCs also will not register an OCX file from a different 32bit installer: Both PCs are relatively new and have standard software installed. We use MS Forefront for security, but disabling that didn't change the behavior. What am I missing?

  Read the article

• Windows 7 restarts while being idle

  - by Ondrej Slinták

  My Windows 7 almost always restarts when I keep it idle for ~20-30mins. It happened randomly before, but lately, if I leave the computer I can be sure it's gonna restart after those 30mins. It never happens when I play games or work tho, just when it's idle. It's a fresh install of Windows 7 64bit. I had also problems while installing it, it always crashed while finalizing the install and I had to reinstall again. Eventually it installed on 3rd or 4th try after I deleted all of my partitions and added them again. I thought it might have been a hardware problem, but temperatures seem to be okay and I have no idea how to track what might have been causing it. Any ideas? I'm running Windows 7 64bit on: Gigabyte EX58-UD4P Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz NVIDIA GeForce GTX 260 6GB of DDR3 1066Mhz RAM WDC WD1001FALS-00J7B0 1TB SATA II I have a very bad feeling it might be something with HDD and its compatibility with Windows 7 as I haven't had those problems for 1 year while I had Vista. Edit: I checked Event Viewer critical errors from this night. PC restarted first time at 11:12pm, then at 3:06am and since then every ~20min until I came back to it. Error message is: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Source: Kernel-Power

  Read the article

• Are my iptables secure?

  - by Patricia

  I have this in my rc.local on my new Ubuntu server: iptables -F iptables -A INPUT -i eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 9418 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 9418 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 5000 -m state --state NEW,ESTABLISHED -j ACCEPT # Heroku iptables -A INPUT -i eth0 -p tcp --sport 5000 -m state --state ESTABLISHED -j ACCEPT # Heroku iptables -A INPUT -p udp -s 74.207.242.5/32 --source-port 53 -d 0/0 --destination-port 1024:65535 -j ACCEPT iptables -A INPUT -p udp -s 74.207.241.5/32 --source-port 53 -d 0/0 --destination-port 1024:65535 -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 443 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 443 -m state --state ESTABLISHED -j ACCEPT iptables -P INPUT DROP iptables -P FORWARD DROP 9418 is Git's port. 5000 is a port used to manage Heroku apps. And 74.207.242.5 and 74.207.241.5 are our DNS servers. Do you think that this is secure? Can you see any holes here? Update: Why is it important to block OUTPUT? This machine will be used only by me.

  Read the article

• Reconfiguring PHP with OpenSSL Extension on CentOS

  - by Evan

  Hi Guys - Long time browser, first time poster! I have a CentOS Dedicated server running just fine. I'm trying to reconfigure PHP to include the OpenSSL extensions so I can use some of the Youtube API's. I installed OpenSSL with yum, so it's in place on the server. I'm just now having trouble getting PHP to use it as an extension. I got the latest PHP tarball, untarred, set my configure string (./configure) using the proper parameter for openssl (--with-openssl=/usr) and it checked out just fine. I ran Make, then Make Install. I am getting hung up here. After it makes the PEAR config file it seems to quit. I guess I'm not sure, but it seems like there is a LOT more that should be happening. Here is a screenshot: http://www.evanfell.com/screencaps/6iamks.png Restarting apache shows no change to the PHP running on the server. Is there are PEAR issue killing the Install process? Or is there an other issue? Thanks In Advance. Happy to clarify and provide more info.

  Read the article

• Does the same lame settings (--alt-preset standard) have differrent names?

  - by erikric

  I've always used windows, and therefore EAC to rip my CDs, but since I've started using Ubuntu more often, I decided to try to rip some albums there. I ended up using k3b (since I found it in the Ubuntu Software center. Tried to install RubyRipper first, but when 'sudo apt-get install ' or UDC fails, a Windows user like me is lost) The real question here is about the settings for the lame encoder. I'm used to just writing --alt-preset standard, and everything works like a charm, but the default in k3b look like this: lame -r --bitwidth 16 --little-endian -s 44.1 -h --tt %t --ta %a --tl %m --ty %y --tc %c --tn %n - %f I assume these are some sensible lame settings, and not a malicious perl script (although it looks like it). It seems to me like some of these ought to be there, and that I can not overwrite the whole thing with my good ol' --alt-preset. So, the question is do I need to replace anything, or is -h the same as old --alt-preset? Is it a difference between '--preset standard' and '--alt-preset standard'? And are those the same as -V 2?

  Read the article

• iptables captive portal remove user

  - by Burgos

  I followed this guide: http://aryo.info/labs/captive-portal-using-php-and-iptables.html I am implementing captive portal using iptables. I've setup web server and iptables on linux router, and everything is working as it should. I can allow user to access internet with sudo iptables -I internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN and I can remove access with sudo iptables -D internet -t mangle -m mac --mac-source USER_MAC_ADDRESS -j RETURN However, on removal, user can still open last viewed page as many times he wants (if he restart his Ethernet adapter, future connections will be closed). On blog page I found a script /usr/sbin/conntrack -L \ |grep $1 \ |grep ESTAB \ |grep 'dport=80' \ |awk \ "{ system(\"conntrack -D --orig-src $1 --orig-dst \" \ substr(\$6,5) \" -p tcp --orig-port-src \" substr(\$7,7) \" \ --orig-port-dst 80\"); }" Which should remove their "redirection" connection track, as it is written, but when I execute that script, nothing happens - user still have access to that page. When I execute /usr/sbin/conntrack -L | grep USER_IP after executing script I am having nothing returned, so my questions: Is there anything else that can help me clean these track? Obviously - I can't reset nor mine, nor users network adapter.

  Read the article

• How to get Synergy working on Ubuntu 11.10 and Windows 7?

  - by Linda

  I'm using Ubuntu 11.10 32-bit and Windows 7 64-bit, however, Synergy only works when a window (application or folder) is open and touching the edge of the screen where the mouse should "jump". In other words, if a window is open and maximized, Synergy works normally. Without any windows, the mouse does not jump to the other screen. My steps: (Ubuntu) apt-get install -y quicksynergy (Windows) Install Synergy (I've tried both 1.3.8 and 1.4.8 and both 32 and 64-bit) On Ubuntu 11.10 32-bit (Synergy Server config): ~/.quicksynergy/synergy.conf section: screens myubuntu: mywin7: end section: links myubuntu: right = mywin7 mywin7: left = myubuntu end On Ubuntu 11.10 32-bit: $ /usr/bin/synergys -f --config .quicksynergy/synergy.conf ... 2012-04-25T14:04:12 NOTE: client "mywin7" has connected /build/buildd/synergy-1.3.6/lib/server/CServer.cpp,287 (output hangs here) On Windows 7 64-bit: Synergy 1.3.8 Client on Microsoft Windows 7 x86 (WOW64) started client connecting to 'myubuntu': ###.###.###.###:24800 connected to server (output hangs here) At this point, things should work, but my mouse still can't change screens unless a window is maximized on my Ubuntu machine. Everything is running on port 24800. No firewall on Ubuntu. Firewall port 24800 open on Windows 7. This was previously working on Ubuntu 10.10 and Windows 7 (so only Ubuntu has been upgraded). I'm open to using either 32 or 64-bit on either server or client side, but I just want to get it working on Ubuntu 11.10 and Windows 7! I'm also using Ubuntu Classic (no effects), and not Unity.

  Read the article

• Domain workstation acting up and I can't track it down.

  - by DevNULL

  I have a developer with a Windows XP (SP2) 64 bit machine. If the machine is left on overnight (or any period of time longer than 5-6 hours) it takes 2-3 minutes to open any local drive and his network drives are no longer accessible. Here's what the system logs report... Any Help BTW: The problem just started a week ago and nothing has changed on the domain controller / AD or his machine. --- ERROR 1 Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 5719 Date: 6/8/2010 Time: 9:17:26 AM User: N/A Computer: BFC1 Description: This computer was not able to set up a secure session with a domain controller in domain UR due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. ADDITIONAL INFO If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified domain. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 5e 00 00 c0 ^..A --- ERROR 2 The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID {555F3418-D99E-4E51-800A-6E89CFD8B1D7} to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19). This security permission can be modified using the Component Services administrative tool. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. --- ERROR 3 Event Type: Error Event Source: RemoteAccess Event Category: None Event ID: 20106 Date: 6/8/2010 Time: 10:12:18 AM User: N/A Computer: BFC1 Description: Unable to add the interface {E76F0A78-7A0B-4EBB-A081-BA3BD452FC4C} with the Router Manager for the IP protocol. The following error occurred: Cannot complete this function. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: eb 03 00 00 e...

  Read the article

• Gnome-panel disappearance in Ubuntu 10.10

  - by jurchiks

  Just today, after about a week of somewhat normal running (I'm a total beginner in Linux and the level of amazingly stupid problems I encountered made me go nuts), today my panel disappeared (the one with Applications/System menus, you'd call it taskbar in Windows). Also, Alt+F2 doesn't work and Ctrl+Alt+Backspace has no effect (I'd think it's supposed to do something). I tried the solution posted here: Panel doesn't show at startup at Ubuntu 10.04 No luck, didn't change absolutely anything. I also couldn't find the .gconf and .gconfd folders using search, so couldn't try that option. There were ones that had same names but without the dot though, but there were several so I didn't risk. What could possibly be the reason for this? All I did yesterday was try to install some updates (another extremely dumb problem - doesn't allow to install even the official updates - "insecure sources" or smth like that, tried fixing it with some tutorials on the net but in the end it worked only for half a day and went back to refusal mode :@) and very few tools from the Ubuntu Software Center, but nothing that would change system settings just by installing it.

  Read the article

• Problems installing GIT on Ubuntu through SSH

  - by jamadri

  I'm having trouble installing git using this command: sudo apt-get install git-core It's giving me the problems below and I'm not quite sure how to get this to work correctly. I try running sudo apt-get update and after it just gives me problems. If anyone knows how to solve this or a possible way of getting GIT on your machine differently it would be of much help. I've never had a problem with using apt-get. Do you want to continue [Y/n]? y WARNING: The following packages cannot be authenticated! liberror-perl git-core patch Install these packages without verification [y/N]? y Err http://us.archive.ubuntu.com jaunty/main git-core 1:1.6.0.4-1ubuntu2 404 Not Found [IP: 91.189.92.183 80] Err http://us.archive.ubuntu.com jaunty/main patch 2.5.9-5 404 Not Found [IP: 91.189.92.183 80] Failed to fetch http://us.archive.ubuntu.com/ubuntu/pool/main/g/git-core/git-core_1.6.0.4- 1ubuntu2_amd64.deb 404 Not Found [IP: 91.189.92.183 80] Failed to fetch http://us.archive.ubuntu.com/ubuntu/pool/main/p/patch/patch_2.5.9- 5_amd64.deb 404 Not Found [IP: 91.189.92.183 80] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Anything reply that can help fix this would be helpful. I'm not sure if it's the git servers or my connection that might be the problem. I've used apt-get to pull other things, it's just failing with git.

  Read the article

• Shut Out of XP - No Admin Password or CDR

  - by ashes999

  I inherited an old WinXP/Linux dual-boot machine from the stoneage. Because it has Linux, the regular boot process is replaced with the Fedora boot loader; I cannot, therefore, press F8 strategically to tell my PC to boot from CD. Even if I could, it's a moot point; the CDR doesn't seem to recognize any CDs. To make things worse, there's no option to network boot. The original user is probably long gone; I don't know the password for any of the Administrator group users. I can login using my corp account, but that's unprivileged on this machine. Since I'm not an admin, I can't do crazy things, like looking at boot.ini. Or deleting files. I only have 500MB free on my C drive. I'm pretty sure I can't boot from a USB, since I didn't see any settings for this in my BIOS. How can I get admin access for my user? Edit: Things I've tried: Boot from CD (CD not recognized) Launch CD from XP (CD not recognized) Install Daemon Tools Lite so I can install from an ISO -- don't have admin privileges XP password recovery tool -- requires admin privileges Adding an admin user -- no access to Control Panel Users since I'm not an admin Logging in as both the admin users on the system (trying some standard passwords) Using Fedora to chntpw (the Fedora version installed is ancient -- 2.7)

  Read the article

• iptables to block non-VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• Issues with VSFTPD / FTP on Linux Ubuntu server - Steps for Troubleshooting?

  - by jnolte

  I am dealing with an issue I am unclear on how to resolve and have been pulling my hair out for some time. I have been trying to configure an FTP user using the following (we use this same documentation on all servers) Install FTP Server apt-get install vsftpd Enable local_enable and write_enable to YES and anonymous user to NO in /etc/vsftpd.conf restart - service vsftpd restart - to allow changes to take place Add WordPress User for FTP access in WP Admin Create a fake shell for the user add "usr/sbin/nologin" to the bottom of the /etc/shells file Add a FTP user account useradd username -d /var/www/ -s /usr/sbin/nologin passwd username add these lines to the bottom of /etc/vsftpd.conf - userlist_file=/etc/vsftpd.userlist - userlist_enable=YES - userlist_deny=NO Add username to the list at top of /etc/vsftpd.userlist restart vsftpd "service vsftpd restart" make sure firewall is open for ftp "ufw allow ftp" allow modify the /var/www directory for username "chown -R /var/www I have also went through everything listed on this post and no luck. I am getting connection refused. Sorry for the poor text formatting above. I think you get the idea. This is something we do over and over and for some reason it is not cooperating here. Setup is Ubuntu 12.04LTS and VSFTPD v2.3.5 Thank you in advance.

  Read the article

• Pip installs on Archlinux fails to build egg

  - by stmfunk

  I was trying to install nltk on my Archlinux server but it repeatedly fails with the following error output /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'entry_points' warnings.warn(msg) /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'zip_safe' warnings.warn(msg) /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'test_suite' warnings.warn(msg) usage: setup.py [global_opts] cmd1 [cmd1_opts] [cmd2 [cmd2_opts] ...] or: setup.py --help [cmd1 cmd2 ...] or: setup.py --help-commands or: setup.py cmd --help error: invalid command 'bdist_egg' /tmp/pip_build_root/nltk/distribute-0.6.21-py3.3.egg Traceback (most recent call last): File "./distribute_setup.py", line 143, in use_setuptools raise ImportError ImportError During handling of the above exception, another exception occurred: Traceback (most recent call last): File "", line 16, in File "/tmp/pip_build_root/nltk/setup.py", line 23, in distribute_setup.use_setuptools() File "./distribute_setup.py", line 145, in use_setuptools return _do_download(version, download_base, to_dir, download_delay) File "./distribute_setup.py", line 125, in _do_download _build_egg(egg, tarball, to_dir) File "./distribute_setup.py", line 116, in _build_egg raise IOError('Could not build the egg.') OSError: Could not build the egg. ---------------------------------------- Cleaning up... Command python setup.py egg_info failed with error code 1 in /tmp/pip_build_root/nltk Storing complete log in /root/.pip/pip.log This error is also occurring for matplotlib buts thats the only other library I found it to fail on so far. pyyaml installs fine. The install works perfectly under virtualenv on my mac which is using python 2.7 but the server is using python 3.3. Any help is appreciated.

  Read the article

• Diagnosing Logon Audit Failure event log entries

  - by Scott Mitchell

  I help a client manage a website that is run on a dedicated web server at a hosting company. Recently, we noticed that over the last two weeks there have been tens of thousands of Audit Failure entries in the Security Event Log with Task Category of Logon - these have been coming in about every two seconds, but interesting stopped altogether as of two days ago. In general, the event description looks like the following: An account failed to log on. Subject: Security ID: SYSTEM Account Name: ...The Hosting Account... Account Domain: ...The Domain... Logon ID: 0x3e7 Logon Type: 10 Account For Which Logon Failed: Security ID: NULL SID Account Name: david Account Domain: ...The Domain... Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x154c Caller Process Name: C:\Windows\System32\winlogon.exe Network Information: Workstation Name: ...The Domain... Source Network Address: 173.231.24.18 Source Port: 1605 The value in the Account Name field differs. Above you see "david" but there are ones with "john", "console", "sys", and even ones like "support83423" and whatnot. The Logon Type field indicates that the logon attempt was a remote interactive attempt via Terminal Services or Remote Desktop. My presumption is that these are some brute force attacks attempting to guess username/password combinations in order to log into our dedicated server. Are these presumptions correct? Are these types of attacks pretty common? Is there a way to help stop these types of attacks? We need to be able to access the desktop via Remote Desktop so simply turning off that service is not feasible. Thanks

  Read the article

• ClassNotFoundException returned for all plugins

  - by razumny

  I am trying to use a Java applet (any Java Applet), but I always get a messages saying "Error. Click for details". When I do so, the pop-up says: Application Error ClassNotFoundException jreVerification.class When I click the "Details" button, all I see is the following: Java Plug-in 10.7.2.10 Using JRE version 1.7.0_07-b10 Java HotSpot(TM) Client VM User home directory = C:\Users\razumny ---------------------------------------------------- c: clear console window f: finalize objects on finalization queue g: garbage collect h: display this help message l: dump classloader list m: print memory usage o: trigger logging q: hide console r: reload policy configuration s: dump system and deployment properties t: dump thread list v: dump thread stack x: clear classloader cache 0-5: set trace level to <n> ---------------------------------------------------- I am running Windows 7 Professional, and am up to date on patches. The problem occurs in Google Chrome, Mozilla Firefox and Internet Explorer, regardless of what Java Applet I am running. The error I quoted above came from here: http://java.com/en/download/installed.jsp?detect=jre I have attempted the following to rectify the issue: Uninstall and reinstall Java Uninstall Java, reboot, install Java Uninstall Java, delete all registry entries, reboot, install Java In addition, I have run Malware and Virus scans, none of which have shown anything of relevance. At this point, I am at my wit's end, and so, I turn to you.

  Read the article

• LG LW20 Express won't boot after hdd replace

  - by Mika

  My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

  Read the article

• Installing checkinstall on x86_64 bit

  - by SephMerah

  I downloaded the source for check install. checkinstall-1.6.2.tar.gz. I then tar -xzvf checkinstall-1.6.2.tar.gz Then I make. It prints this error: [root@ip-50-63-180-135 checkinstall-1.6.2]# make for file in locale/checkinstall-*.po ; do \ case ${file} in \ locale/checkinstall-template.po) ;; \ *) \ out=`echo $file | sed -s 's/po/mo/'` ; \ msgfmt -o ${out} ${file} ; \ if [ $? != 0 ] ; then \ exit 1 ; \ fi ; \ ;; \ esac ; \ done make -C installwatch make[1]: Entering directory `/home/sofiane/checkinstall-1.6.2/installwatch' gcc -Wall -c -D_GNU_SOURCE -DPIC -fPIC -D_REENTRANT -DVERSION=\"0.7.0beta7\" installwatch.c installwatch.c:2942: error: conflicting types for 'readlink' /usr/include/unistd.h:828: note: previous declaration of 'readlink' was here installwatch.c:3080: error: conflicting types for 'scandir' /usr/include/dirent.h:252: note: previous declaration of 'scandir' was here installwatch.c:3692: error: conflicting types for 'scandir64' /usr/include/dirent.h:275: note: previous declaration of 'scandir64' was here make[1]: *** [installwatch.o] Error 1 make[1]: Leaving directory `/home/sofiane/checkinstall-1.6.2/installwatch' make: *** [all] Error 2 I searched extensively on this issue and this solution looks promising. Should I attempt to install checkinstall as an fpm? What would be the best way to go about that? Centos 6.3 x86_64

  Read the article

< Previous Page | 709 710 711 712 713 714 715 716 717 718 719 720  | Next Page >