Search Results

Search found 23614 results on 945 pages for 'update from'.

Page 714/945 | < Previous Page | 710 711 712 713 714 715 716 717 718 719 720 721  | Next Page >

  • iptables configuration to work with apache2 mod_proxy

    - by swdalex
    Hello! I have iptables config like this: iptables -F INPUT iptables -F OUTPUT iptables -F FORWARD iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --sport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A OUTPUT -p tcp --sport 443 -j ACCEPT Also, I have apache virtual host: <VirtualHost *:80> ServerName wiki.myite.com <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8901/ ProxyPassReverse / http://localhost:8901/ <Location /> Order allow,deny Allow from all </Location> </VirtualHost> My primary domain www.mysite.com is working well with this configuration (I don't use proxy redirect on it). But my virtual host wiki.mysite.com is not responding. Please, help me to setup iptables config to allow wiki.mysite.com working too. I think, I need to setup iptables FORWARDING options, but I don't know how. update: I have 1 server with 1 IP. On server I have apache2.2 on 80 port. Also I have tomcat6 on 8901 port. In apache I setup to forwarding domain wiki.mysite.com to tomcat (mysite.com:8901). I want to secure my server by disabling all ports, except 80, 22 and 443.

    Read the article

  • Migrating Windows 2003 File Server Cluster to Windows 2008 R2 Standalone?

    - by Tatas
    We have a situation where we have an aging Windows 2003 File Server Cluster that we'd like to move to a standalone Windows Server 2008 R2 VM that resides in our Hyper-V R2 installation. We see no need to keep the Clustering as Hyper-V is now providing our Failover/Redundancy. Usually, in a standalone file server migration we migrate the data, preserving NTFS permissions and then export the sharing permissions from the registry and import them on the new server. This does not appear possible in this instance, as the 2003 cluster stores the sharing permissions quite differently. My question is, how would one perform this type of migration? Is it even possible? My current lead is the File Server Migration Toolkit, however I can find no information on the net about migrating from cluster to standalone, only the opposite. Please help. UPDATE: We ended up getting the data copied over (permissions intact), but had to recreate the shares manually by hand. It was a bit of a pain but it did in the end work out.

    Read the article

  • Changing the interface language in Windows 7 Home Premium

    - by Cristián Romo
    A friend of mine has recently purchased a laptop in the U.S. that has Windows 7 Home Premium on it with an English interface. Not being a native English speaker, I'm trying to change the interface language to traditional Chinese. I've looked through the Control Panel in search of something that might let me change the interface language. Naturally, I looked at the Region and Language section and managed to change the formats the computer uses and install a working keyboard, but I haven't found a way to change the interface language. Upon doing some research, I found out that there are two kinds of interface packs, Multilingual User Interface (MUI) and Language Interface Packs (LIP). It seems that MUIs can only be installed through Windows Update, so I looked through the list of updates. To my dismay, the language packs are not present. The optional updates tab doesn't even show up. Many sites show a drop down menu the under Keyboards and Languages tab in the Region and Language options, yet it doesn't show up for me. We also don't have the Windows 7 DVD which might contain this useful file. As far as the LIPs go, I can't find one in Chinese at all, let alone traditional Chinese. Can the interface language be changed in Home Premium at all? If it can, how would I do so?

    Read the article

  • How to install a private user script in Chrome 21+?

    - by Mathias Bynens
    In Chrome 20 and older versions, you could simply open any .user.js file in Chrome and it would prompt you to install the user script. However, in Chrome 21 and up, it downloads the file instead, and displays a warning at the top saying “Extensions, apps, and user scripts can only be added from the Chrome Web Store”. The “Learn More” link points to http://support.google.com/chrome_webstore/bin/answer.py?hl=en&answer=2664769, but that page doesn’t say anything about user scripts, only about extensions in .crx format, apps, and themes. This part sounded interesting: Enterprise Administrators: You can specify URLs that are allowed to install extensions, apps, and themes directly through the ExtensionInstallSources policy. So, I ran the following commands, then restarted Chrome and Chrome Canary: defaults write com.google.Chrome ExtensionInstallSources -array "https://gist.github.com/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://gist.github.com/*" Sadly, these settings only seem to affect extensions, apps, and themes (as it says in the text), not user scripts. (I’ve filed a bug asking to make this setting affect user scripts as well.) Any ideas on how to install a private user script (that I don’t want to add to the Chrome Web Store) in Chrome 21+? Update: The problem was that gist.github.com’s raw URLs redirect to a different domain. So, use these commands instead: # Allow installing user scripts via GitHub or Userscripts.org defaults write com.google.Chrome ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" defaults write com.google.Chrome.canary ExtensionInstallSources -array "https://*.github.com/*" "http://userscripts.org/*" This works!

    Read the article

  • Best Practical RT, sorting email into queues automatically using procmail

    - by user52095
    I'm trying to get incoming e-mail to automatically go directly into whichever queue/ticket they are related to or create a new one if none exist and the right queue e-mail setup in the web interface is used. I will have too many queues to have two line items within mailgate per queue. A similar issue was discussed here (http://serverfault.com/questions/104779/procmail-pipe-to-program-otherwise-return-error-to-sender), but I thought it best to open a new case instead of tagging on what appeared to be an answer to that person's query. I'm able to send and receive e-mail (via PostFix) to the default rt user and this user successfully accepts all e-mail for the relative domain. I have no idea where the e-mail goes - it's successfully delivered, but it does not update existing tickets (with a Subject line match) and it does not create any new. Here's and example of my ./procmail.log: procmail: [23048] Mon Aug 23 14:26:01 2010 procmail: Assigning "MAILDOMAIN=rt.mydomain.com " procmail: Assigning "RT_MAILGATE=/opt/rt3/bin/rt-mailgate " procmail: Assigning "RT_URL=http://rt.mydomain.com/ " procmail: Assigning "LOGABSTRACT=all " procmail: Skipped " " procmail: Skipped " " procmail: Assigning "LASTFOLDER={ " procmail: Opening "{ " procmail: Acquiring kernel-lock procmail: Notified comsat: "rt@18337:./{ " From [email protected] Mon Aug 23 14:26:01 2010 Subject: RE: [RT.mydomain.com #1] Test Ticket Folder: { 1616 Does the notified comsat portion mean that it notified RT? The contents of my ./procmailrc: #Preliminaries SHELL=/bin/sh #Use the Bourne shell (check your path!) #MAILDIR=${HOME} #First check what your mail directory is! MAILDIR="/var/mail/rt/" LOGFILE="home/rt//procmail.log" LOG="--- Logging ${LOGFILE} for ${LOGNAME}, " VERBOSE=yes MAILDOMAIN="rt.mydomain.com" RT_MAILGATE="/opt/rt3/bin/rt-mailgate" #RT_MAILGATE="/usr/local/bin/rt-mailgate" RT_URL="http://rt.mydomain.com/" LOGABSTRACT=all :0 { # the following line extracts the recipient from Received-headers. # Simply using the To: does not work, as tickets are often created # by sending a CC/BCC to RT TO=`formail -c -xReceived: |grep $MAILDOMAIN |sed -e 's/.*for *<*\(.*\)>* *;.*$/\1/'` QUEUE=`echo $TO| $HOME/get_queue.pl` ACTION=`echo $TO| $HOME/get_action.pl` :0 h b w |/usr/bin/perl $RT_MAILGATE --queue $QUEUE --action $ACTION --url $RT_URL } I know that my get_queue.pl and get_action.pl scripts work, as those have been previously tested. Any help and/or guidance you can give would be greatly appreciated. Nicôle

    Read the article

  • EC2 Configuration

    - by user123683
    I am trying to create a server structure for my EC2 account. The design I have chosen consists of 2 instances running in different availability zones, elastic load balancer, an auto-scaling group with cloudwatch monitoring configured and a security group defining rules for access to the instances. This setup is to support an online web application written in PHP. I am trying to decide what is a better policy: Store MySQL DB on a separate Instance Store MySQL DB on an attached EBS volume (from what i know auto-scaling will not replicate the attached EBS volume but will generate new instances from a chosen AMI - is this view correct?) Regards the AMI I plan to use a basic Amazon linux 64 bit AMI, and install bastille (maybe OSSEC) but I am looking to also use an encrypted file system. Are there any issues using an encrypted file system and communication between the DB and webapp i neeed to be aware of? Are there any comms issues using the encrypted filesystem on the instance housing the webapp I was going to launch a second instance or attach a second volume in the second availability zone to act as a standby for the database - I'm just looking for some suggestions about how to get the two DB's to talk - will this be a big task Regards updates for security is it best to create a recent snapshot and just relaunch and allow Amazon to install updates on launch or is the yum update mechanism a suitable alternative - is it better practice to relaunch instead of updates being installed which force a restart. I plan to create two AMI snapshots one for the app server and one for the DB each with the same security measures in place - is this a reasonable - I just figure it is a better policy than having additional applications that are unnecessary included in a AMI that I intend on using. My plan for backup is to create periodic snapshots of the webapp and DB instances (if I use an additional EBS volume instead of separate instances my understanding is that the EBS volume will persist in S3 storage in the event of an unexpected termination and I can create snapshots of the volume backup purposes). Thanks in advance for suggestions and advice. I am new to EC2 and I may have described unnecessary overkill but I want to try implement what can be considered a best practice solution so all advice is appreciated.

    Read the article

  • Apache + Codeigniter + New Server + Unexpected Errors

    - by ngl5000
    Alright here is the situation: I use to have my codeigniter site at bluehost were I did not have root access, I have since moved that site to rackspace. I have not changed any of the PHP code yet there has been some unexpected behavior. Unexpected Behavior: http://mysite.com/robots.txt Both old and new resolve to the robots file http://mysite.com/robots.txt/ The old bluehost setup resolves to my codeigniter 404 error page. The rackspace config resolves to: Not Found The requested URL /robots.txt/ was not found on this server. **This instance leads me to believe that there could be a problem with my mod rewrites or lack there of. The first one produces the error correctly through php while it seems the second senario lets the server handle this error. The next instance of this problem is even more troubling: 'http://mysite.com/search/term/9 x 1-1%2F2 white/' New site results in: Bad Request Your browser sent a request that this server could not understand. Old site results in: The actual page being loaded and the search term being unencoded. I have to assume that this has something to do with the fact that when I went to the new server I went from root level htaccess file to httpd.conf file and virtual server default and default-ssl. Here they are: Default file: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName mysite.com DocumentRoot /var/www <Directory /> Options +FollowSymLinks AllowOverride None </Directory> <Directory /var/www> Options -Indexes +FollowSymLinks -MultiViews AllowOverride None Order allow,deny allow from all RewriteEngine On RewriteBase / # force no www. (also does the IP thing) RewriteCond %{HTTPS} !=on RewriteCond %{HTTP_HOST} !^mysite\.com [NC] RewriteRule ^(.*)$ http://mysite.com/$1 [R=301,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.+)\.(\d+)\.(js|css|png|jpg|gif)$ $1.$3 [L] # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] # codeigniter direct RewriteCond $0 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^.*$ index.php [L] </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> Default-ssl File <IfModule mod_ssl.c> <VirtualHost _default_:443> ServerAdmin webmaster@localhost ServerName mysite.com DocumentRoot /var/www <Directory /> Options +FollowSymLinks AllowOverride None </Directory> <Directory /var/www> Options -Indexes +FollowSymLinks -MultiViews AllowOverride None Order allow,deny allow from all RewriteEngine On RewriteBase / RewriteCond %{SERVER_PORT} !^443 RewriteRule ^ https://mysite.com%{REQUEST_URI} [R=301,L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.+)\.(\d+)\.(js|css|png|jpg|gif)$ $1.$3 [L] # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] # codeigniter direct RewriteCond $0 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^.*$ index.php [L] </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> # SSL Engine Switch: # Enable/Disable SSL for this virtual host. SSLEngine on # Use our self-signed certificate by default SSLCertificateFile /etc/apache2/ssl/certs/www.mysite.com.crt SSLCertificateKeyFile /etc/apache2/ssl/private/www.mysite.com.key # A self-signed (snakeoil) certificate can be created by installing # the ssl-cert package. See # /usr/share/doc/apache2.2-common/README.Debian.gz for more info. # If both key and certificate are stored in the same file, only the # SSLCertificateFile directive is needed. # SSLCertificateFile /etc/ssl/certs/ssl-cert-snakeoil.pem # SSLCertificateKeyFile /etc/ssl/private/ssl-cert-snakeoil.key # Server Certificate Chain: # Point SSLCertificateChainFile at a file containing the # concatenation of PEM encoded CA certificates which form the # certificate chain for the server certificate. Alternatively # the referenced file can be the same as SSLCertificateFile # when the CA certificates are directly appended to the server # certificate for convinience. #SSLCertificateChainFile /etc/apache2/ssl.crt/server-ca.crt # Certificate Authority (CA): # Set the CA certificate verification path where to find CA # certificates for client authentication or alternatively one # huge file containing all of them (file must be PEM encoded) # Note: Inside SSLCACertificatePath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCACertificatePath /etc/ssl/certs/ #SSLCACertificateFile /etc/apache2/ssl.crt/ca-bundle.crt # Certificate Revocation Lists (CRL): # Set the CA revocation path where to find CA CRLs for client # authentication or alternatively one huge file containing all # of them (file must be PEM encoded) # Note: Inside SSLCARevocationPath you need hash symlinks # to point to the certificate files. Use the provided # Makefile to update the hash symlinks after changes. #SSLCARevocationPath /etc/apache2/ssl.crl/ #SSLCARevocationFile /etc/apache2/ssl.crl/ca-bundle.crl # Client Authentication (Type): # Client certificate verification type and depth. Types are # none, optional, require and optional_no_ca. Depth is a # number which specifies how deeply to verify the certificate # issuer chain before deciding the certificate is not valid. #SSLVerifyClient require #SSLVerifyDepth 10 # Access Control: # With SSLRequire you can do per-directory access control based # on arbitrary complex boolean expressions containing server # variable checks and other lookup directives. The syntax is a # mixture between C and Perl. See the mod_ssl documentation # for more details. #<Location /> #SSLRequire ( %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \ # and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \ # and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \ # and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \ # and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20 ) \ # or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/ #</Location> # SSL Engine Options: # Set various options for the SSL engine. # o FakeBasicAuth: # Translate the client X.509 into a Basic Authorisation. This means that # the standard Auth/DBMAuth methods can be used for access control. The # user name is the `one line' version of the client's X.509 certificate. # Note that no password is obtained from the user. Every entry in the user # file needs this password: `xxj31ZMTZzkVA'. # o ExportCertData: # This exports two additional environment variables: SSL_CLIENT_CERT and # SSL_SERVER_CERT. These contain the PEM-encoded certificates of the # server (always existing) and the client (only existing when client # authentication is used). This can be used to import the certificates # into CGI scripts. # o StdEnvVars: # This exports the standard SSL/TLS related `SSL_*' environment variables. # Per default this exportation is switched off for performance reasons, # because the extraction step is an expensive operation and is usually # useless for serving static content. So one usually enables the # exportation for CGI and SSI requests only. # o StrictRequire: # This denies access when "SSLRequireSSL" or "SSLRequire" applied even # under a "Satisfy any" situation, i.e. when it applies access is denied # and no other module can change it. # o OptRenegotiate: # This enables optimized SSL connection renegotiation handling when SSL # directives are used in per-directory context. #SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory /usr/lib/cgi-bin> SSLOptions +StdEnvVars </Directory> # SSL Protocol Adjustments: # The safe and default but still SSL/TLS standard compliant shutdown # approach is that mod_ssl sends the close notify alert but doesn't wait for # the close notify alert from client. When you need a different shutdown # approach you can use one of the following variables: # o ssl-unclean-shutdown: # This forces an unclean shutdown when the connection is closed, i.e. no # SSL close notify alert is send or allowed to received. This violates # the SSL/TLS standard but is needed for some brain-dead browsers. Use # this when you receive I/O errors because of the standard approach where # mod_ssl sends the close notify alert. # o ssl-accurate-shutdown: # This forces an accurate shutdown when the connection is closed, i.e. a # SSL close notify alert is send and mod_ssl waits for the close notify # alert of the client. This is 100% SSL/TLS standard compliant, but in # practice often causes hanging connections with brain-dead browsers. Use # this only for browsers where you know that their SSL implementation # works correctly. # Notice: Most problems of broken clients are also related to the HTTP # keep-alive facility, so you usually additionally want to disable # keep-alive for those clients, too. Use variable "nokeepalive" for this. # Similarly, one has to force some clients to use HTTP/1.0 to workaround # their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and # "force-response-1.0" for this. BrowserMatch "MSIE [2-6]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 # MSIE 7 and newer should be able to use keepalive BrowserMatch "MSIE [17-9]" ssl-unclean-shutdown httpd.conf File Just a lot of stuff from html5 boiler plate, I will post it if need be Old htaccess file <IfModule mod_rewrite.c> # index.php remove any index.php parts RewriteCond %{THE_REQUEST} /index\.(php|html) RewriteRule (.*)index\.(php|html)(.*)$ /$1$3 [r=301,L] RewriteCond $1 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^(.*)/$ /$1 [r=301,L] # codeigniter direct RewriteCond $1 !^(index\.php|assets|robots\.txt|sitemap\.xml|favicon\.ico) RewriteRule ^(.*)$ /index.php/$1 [L] </IfModule> Any Help would be hugely appreciated!!

    Read the article

  • 'txn-current-lock': Permission denied [500, #13] - Subversion + Apache Configuration Issue

    - by wfoster
    Current Setup Fedora 13 32bit Apache 2.2.16 Subversion repositories setup under /var/www/svn I have two different repositories under this directory so my /etc/httpd/conf.d/subversion.conf setup in this way; LoadModule dav_svn_module modules/mod_dav_svn.so LoadModule authz_svn_module modules/mod_authz_svn.so <Location /svn> DAV svn SVNListParentPath on SVNParentPath /var/www/svn <LimitExcept GET PROPFIND OPTIONS REPORT> AuthType Basic AuthName "Subversion Repository" AuthUserFile /etc/httpd/.htpasswd Require valid-user </LimitExcept> </Location> After copying over my repos and using; chmod 755 -R /var/www/svn chcon -R -t httpd_sys_content_t /var/www/svn chown apache:apache -R /var/www/svn I can browse my repos fine through the browser, and I can update all my working copies, however when I try to check in from anywhere I get the same error Can't open file '/var/www/svn/repo/db/txn-current-lock':Permission denied I have been working on this issue for a while now and cant seem to find a solution to my issues. It might be of some use to know that the repo existed on a different server before this, it has been now moved to this new server. Everything I have read seems to indicate that the permissions for apache are incorrect, however apache is set to run as User apache and Group apache. So as far as I can tell my setup is correct. The behavior is not though. Any Ideas? Solution The only way I was able to get this to work is to disable SELinux, it could also be done by setting the proper booleans with SELinux via setsetbool and getsebool since this is just a home server, I decided to disable SELinux and am reaping the benefits now.

    Read the article

  • How to get an ARM CPU clock speed in Linux?

    - by MiKy
    I have an ARM-based embedded machine based on S3C2416 board. According to the specifications I have available there should be a 533 MHz ARM9 (ARM926EJ-S according to /proc/cpuinfo), however the software running on it "feels" slow, compared to the same software on my Android phone with a 528MHz ARM CPU. /proc/cpuinfo tells me that BogoMIPS is 266.24. I know that I should not trust BogoMIPS regarding performance ("Bogo" = bogus), however I would like to get a measurement on the actual CPU speed. On x86, I could use the rdtsc instruction to get the time stamp counter, wait a second (sleep(1)), read the counter again to get an approximation on the CPU speed, and according to my experience, this value was close enough to the real CPU speed. How can I find the actual CPU speed of given ARM processor? Update I found this simple Pi calculator, which I compiled both for my Android phone and the ARM board. The results are as follows: S3C2416 # cat /proc/cpuinfo Processor : ARM926EJ-S rev 5 (v5l) BogoMIPS : 266.24 Features : swp half fastmult edsp java ... #./pi_arm 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 8.50 sec. (real time) Android # cat /proc/cpuinfo Processor : ARMv6-compatible processor rev 2 (v6l) BogoMIPS : 527.56 Features : swp half thumb fastmult edsp java # ./pi_android 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 5.95 sec. (real time) So it seems that the ARM926EJ-S is slower than my Android phone, but not twice slower as I would expect by the BogoMIPS figures. I am still unsure about the clock speed of the ARM9 CPU.

    Read the article

  • Debugging Samba/CUPS printer sharing with Windows

    - by mrdrbob
    I've got a HP Deskjet hooked up to a Slackware 12.2 box. I've got CUPS set up and can print a test page from the box just fine. I've also got Samba set up and have a couple file shares that work fine. I'm trying to share that HP Deskjet out via Samba, but I can't get it to show up in any Windows system. I see the server and its file shares in Windows networking, but when I open the Printers, no printer shows up. Running net view \\servername from the command line lists the file shares, but no printers. Here's the pertinent part of my smb.conf, if that helps: [global] workgroup = HOMENET security = share hosts allow = 192.168.1. 192.168.2. 127. load printers = yes printcap name = cups printing = cups log file = /var/log/samba.%m max log size = 50 [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes writable = no printable = yes guest only = yes Can anyone give me some pointers as to where to start looking for potential causes? Update: Running testparm shows no errors. Here's the output (minus the file shares): [global] workgroup = HOMENET security = SHARE log file = /var/log/samba.%m max log size = 50 printcap name = cups hosts allow = 192.168.1., 192.168.2., 127. [printers] comment = All Printers path = /var/spool/samba guest only = Yes guest ok = Yes printable = Yes browseable = No

    Read the article

  • Linux Mint reset display resolution from console

    - by wullxz
    I have a Linux Mint 13 Xfce in a VMware Workstation 8 VM and set the resolution from 800x600 to 1280x768 and now I get permanently logged out when I try to login. I knew how to get back to my old resolution back in the xorg.conf days but Linux Mint now uses xrandr which won't display any displays when running # xrandr because X is not running (of course not - I can't login over GUI). I know that there are configuration files in /etc/X11/Xsession.d/ because I configured a debian based thinclient's resolution in a file called /etc/X11/Xsession.d/91configure_display but that file doesn't exist in my Linux Mint VM. So, how do I reset my X screen resolution from console? Edit: I forgot to tell you that I can't change resolution in console: # xrandr -s 800x600 Can't open display This message appears every time I use xrandr or xrandr -s *resolution* Update: I tried what bWowk suggested: # export DISPLAY=:0.0 # xrandr -s 800x600 No protocol specified No protocol specified Can't open display :0.0 So, that doesn't work either. Isn't there a configuration file that is executed every time X starts? X is running btw - ps aux | grep X shows one process /usr/bin/X running.

    Read the article

  • LCD monitor flicker when connected to a laptop using VGA

    - by Björn Lindqvist
    I have a dual screen setup with two AOC e2450Sw monitors connected to a laptop. The laptop has one HDMI and one VGA output. When one of the monitors is connected using VGA, it flickers or displays static noise. The flickering is fairly subtle and only visible on darker colors. But it is there and noticable and appears like horizontal lines. The problem only appears on the monitor connected to the laptop using the VGA cable. If I swap the monitors, the one connected using VGA is displaying the flicker but not the one connected using HDMI. The simple solution would ofcourse be to connect both monitors using HDMI, but since the laptop only has one VGA and one HDMI out that isn't possible. I've tried tweaking the monitor setting using the OSD menu, but it had little or no effect. Update: After several more trouble shooting hours, it seems the problem is not related to the monitor or VGA cable as the problem persists even if I swap the display with another brand and different cables. So it may be the graphics card? Intel HD Graphics 4000. The laptop is Acer Aspire E1-571.

    Read the article

  • How can I find out which processes on my computer are accessing the microphone?

    - by Vinayak
    After reading this interesting Lifehacker post and reading the comments on the page, one person was wondering if it would be possible to use the Physical Device Object Names of other hardware such as the microphone to find out the names of processes using that device. I tried the same approach, but so far it only seems to work for the webcam. Is there any other way I could get this to work in Process Explorer? UPDATE: The Lifehacker post was about finding out which Windows process is currently using your webcam. This is how they went about doing it: Start Device Manager (WIN+R → "devmgmt.msc" → OK) Find your webcam among the list of devices (check under Imaging Devices) Open the properties window of the device and switch to the Details tab (Right click → Properties → Details) In the dropdown menu, select Physical Device Object Name and copy the string(Right click → Copy) Download Process Explorer Make sure you have opened Process Explorer in Administrator Mode(File → Show Details for All Processes) Hit CTRL+F and enter the string you copied earlier(it should be something like \Device\000000XX) Hit the Search button and you should see a list of processes using the webcam(if there are any)

    Read the article

  • How to check DVD region settings in Window 7

    - by jmatthias
    I have installed Windows 7 on my laptop. When I put a movie in the DVD drive, the video player starts up and tells me 'THIS DISC IS NOT FORMATTED TO PLAY IN THIS REGION'. I have changed the DVD region a few times in the past but while I was in Windows XP I changed the region in Region 1. I cannot find how to check the DVD region setting in Windows 7 (it's not located on the hard properties page of the DVD anymore. Does anybody know how to check the DVD region in Windows 7? Update: If I connect an external USB DVD drive I can see the DVD region tab on the hardware properties dialog. I guess there is some compatibility problem with my internal DVD drive and Windows 7 (as I said I was able to inspect/change the DVD region in Windows XP). Solution: I think I had used LtnRPC in the past to remove the region from my DVD drive. It looks like Windows 7 does not like region free DVD drives (at least mine anyway). I was able to use LtnRPC to reset the region back to 1. I can now see the region tab on the DVD drives hardware properties.

    Read the article

  • Debian Squeeze vzquota

    - by benjamin
    Hello, Apparently, I got Debian Squeeze (Debian 6) to work on a VPS using debootstrap and chroot as described here. Subsequent installation of the harden, exim4, mysql-server packages failed partially. Relevant information: insserv: warning: script 'S10vzquota' missing LSB tags and overrides insserv: warning: script is corrupt or invalid: /etc/init.d/../rc6.d/S00vzreboot insserv: warning: script 'vzquota' missing LSB tags and overrides insserv: There is a loop between service vzquota and stop-bootlogd if started insserv: loop involving service stop-bootlogd at depth 2 insserv: loop involving service vzquota at depth 1 insserv: loop involving service rsyslog at depth 1 insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: There is a loop between service vzquota and stop-bootlogd if started insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: exiting now without changing boot order! update-rc.d: error: insserv rejected the script header dpkg: error processing exim4-base (--configure): subprocess installed post-installation script returned error exit status 1 Any suggestions? Keywords: vzquota debian squeeze installation vps, virtual private server.

    Read the article

  • How to handle server failure in an n-tier architecture?

    - by andy
    Imagine I have an n-tier architecture in an auto-scaled cloud environment with say: a load balancer in a failover pair reverse proxy tier web app tier db tier Each tier needs to connect to the instances in the tier below. What are the standard ways of connecting tiers to make them resilient to failure of nodes in each tier? i.e. how does each tier get the IP addresses of each node in the tier below? For example if all reverse proxies should route traffic to all web app nodes, how could they be set up so that they don't send traffic to dead web app nodes, and so that when new web app nodes are brought online they can send traffic to it? I could run an agent that would update all the configs to all the nodes, but it seems inefficient. I could put an LB pair between each tier, so the tier above only needs to connect to the load balancers, but how do I handle the problem of the LBs dying? This just seems to shunt the problem of tier A needing to know the IPs of all nodes in tier B, to all nodes in tier A needing to know the IPs of all LBs between tiers A and B. For some applications, they can implement retry logic if they contact a node in the tier below that doesn't respond, but is there any way that some middleware could direct traffic to only live nodes in the following tier? If I was hosting on AWS I could use an ELB between tiers, but I want to know how I could achieve the same functionality myself. I've read (briefly) about heartbeat and keepalived - are these relevant here? What are the virtual IPs they talk about and how are they managed? Are there still single points of failure using them?

    Read the article

  • Apache 403 after configuring varnish

    - by w0rldart
    I just don't know where else to look and what else to do. I keep getting a 403 error on all my vhosts after setting varnish 3.0 Apacher log: [error] [client 127.0.0.1] client denied by server configuration: /etc/apache2/htdocs Headers: http://domain.com/ GET / HTTP/1.1 Host: domain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:16.0) Gecko/20100101 Firefox/16.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Connection: keep-alive Cookie: __utma=106762181.277908140.1348005089.1354040972.1354058508.6; __utmz=106762181.1348005089.1.1.utmcsr=OTHERDOMAIN.com|utmccn=(referral)|utmcmd=referral|utmcct=/galerias/cocinas Cache-Control: max-age=0 HTTP/1.1 403 Forbidden Vary: Accept-Encoding Content-Encoding: gzip Content-Type: text/html; charset=iso-8859-1 X-Cacheable: YES Content-Length: 223 Accept-Ranges: bytes Date: Sat, 01 Dec 2012 20:35:14 GMT X-Varnish: 1030961813 1030961811 Age: 26 Via: 1.1 varnish Connection: keep-alive X-Cache: HIT ---------------------------------------------------------- /etc/default/varnish: DAEMON_OPTS="-a ip.ip.ip.ip:80 \ -T localhost:6082 \ -f /etc/varnish/main.domain.vcl \ -S /etc/varnish/secret \ -s file,/var/lib/varnish/$INSTANCE/varnish_storage.bin,1G" #-s malloc,256m" My vcl file: http://pastebin.com/axJ57kD8 So, any ideas what I could be missing? Update Just so you know, ports: NameVirtualHost *:8000 Listen 8000 and <VirtualHost 205.13.12.12:8000>

    Read the article

  • PHP - Centos OpenSSL error

    - by mabbs
    i'm currently having a problem with OpenSSL on my Centos 6.5 Server. it ran perfectly fine until sunday. and i checked the error_log and i saw this error in the log PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/openssl.so' - /usr/lib64/php/modules/openssl.so: cannot open shared object file: No such file or directory in Unknown on line 0 i tried phpinfo(); and i found that openssl is enabled i tried php -m it returned [PHP Modules] bz2 calendar Core ctype curl date dom ereg exif fileinfo filter ftp gd gettext gmp hash iconv interbase json libxml mbstring mcrypt memcache mysql mysqli openssl pcntl pcre PDO PDO_Firebird pdo_mysql pdo_sqlite Phar pspell readline Reflection session shmop SimpleXML snmp sockets SPL sqlite3 standard tokenizer wddx xml xmlreader xmlrpc xmlwriter xsl zip zlib UPDATE this is what i got from rpm -qa | grep php just like what Mike Suggested php-php-gettext-1.0.11-3.el6.noarch php-mcrypt-5.3.3-3.el6.x86_64 php-interbase-5.3.3-3.el6.x86_64 php-pdo-5.3.3-27.el6_5.1.x86_64 php-5.3.3-27.el6_5.1.x86_64 php-mysql-5.3.3-27.el6_5.1.x86_64 php-snmp-5.3.3-27.el6_5.1.x86_64 php-gd-5.3.3-27.el6_5.1.x86_64 php-xml-5.3.3-27.el6_5.1.x86_64 php-pear-1.9.4-4.el6.noarch php-pecl-memcache-3.0.5-4.el6.x86_64 phpMyAdmin-3.5.8.2-1.el6.noarch php-common-5.3.3-27.el6_5.1.x86_64 php-cli-5.3.3-27.el6_5.1.x86_64 php-devel-5.3.3-27.el6_5.1.x86_64 php-mbstring-5.3.3-27.el6_5.1.x86_64 php-xmlrpc-5.3.3-27.el6_5.1.x86_64 php-pspell-5.3.3-27.el6_5.1.x86_64

    Read the article

  • Cannot Delete Item "Could Not Find This Item" issue

    - by aronchick
    A friend sent a long a file (a .rar) he wanted me to check out for him before he installed it. I downloaded it and unrared it with no problems, but it was full of .exe's instead of the intended contents (fonts) so I advised him to delete it immediately and not use. I then proceeded to do the same, but the folder simply will not delete. Oddly the files went fine, and I never ran anything, but this is what I'm seeing: Could not find this item This is no longer located in C:\Users\This_User\Desktop. verify the item's location and try again. I've tried the following things with no help: Using "Unlocker" to Unlock and delete Using move on reboot and rebooting Using PendMoves (from sysinternals) and rebooting Elevating a cmd line, doing a dir /x to get the short name of the folder, and then del 'shortna~1' Moving the folder to a new folder and then trying to delete the parent folder I'm on Windows 7 RTM, very fresh install. Any thoughts? Update: Just to confirm, I've run Hijack this and half a dozen other malware detectors, and everything came back clean (no extra processes, no other obvious badness). Rebooting in safe mode didn't help either.

    Read the article

  • Intel DriverInstall issue on HP ProLiant server DL580G5

    - by TomTom
    Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

    Read the article

  • Spotlight can't see anything in Applications

    - by mix
    There have been other threads on this but none of the solutions mentioned have helped me. Spotlight has stopped showing any results for my Applications. I've tried reindexing and removing the index so it rebuilds it. No change. I've tried adding Applications to the Privacy tab and removing it, no change. I tried repairing disk permissions and redoing the above, no change. I've tried removing everything from the index except Applications and then I just get nothing for any search at all (except dictionary entries). I tried adding a symlink in my homedir to Applications and reindexing, but no change. Any ideas on what to do? I'm running Snow Leopard. This is driving me crazy! Update: I've noticed that when I start a reindex with sudo mdutil -E / and then immediately do a spotlight search for an app that the app shows up temporarily until spotlight gets disabled due to active indexing. After the indexing is done the app entries go away.

    Read the article

  • Ubuntu 10.04 Keyboard and Mouse Freezing Problem

    - by nitbuntu
    I had a partition setup with Windows XP and Ubuntu 8.04 dual booting. I recently upgraded to Ubuntu 10.04 by installing fresh from CD but leaving the previous /home folder as is. Things seemed to be working fine, but started finding that my mouse and keyboard were freezing. After a quick search on the internet, I found the following suggestions as shown here:- Ubuntu Forums Here the suggestion was to:- Edit /etc/default/grub, go to the line that begins like: GRUB_CMDLINE_LINUX_DEFAULT= Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi=off" After that, run this command: sudo update-grub and Reboot This seemed to have resolved the issue but after a couple of days I again find my mouse and keyboard freezing. I also find that my parallel port printer had also stopped working. I have saved the output of dmesg and my syslog. The first can be viewed here but the syslog had too many characters, so if someone can suggest an alternative to freetexthost, I can post it there. Moreover, if there is any other information that should be provided, do let me know. I do hope we can get to the bottom of this issue. Thank you in advance for any help that could be provided.

    Read the article

  • Create a special folder within an outlook PST file

    - by Tony Dallimore
    Original question I have two problems caused by missing special folders. I added a second email address for which Outlook created a new PST file with an Inbox to which emails are successfully imported. But there is no Deleted Items folder. If I attempt to delete an unwanted email it is struck out. If move an email to a different PST file it is copied. I created a new PST file using Data File Management. This PST file has no Drafts folder. This is not important but I fail to see why I cannot have Drafts folder if I want. Any suggestions for solving these problems, particularly the first, gratefully received. Update Thanks to Ramhound and Dave Rook for their helpful responses to my original question. I assumed the problem of not have a Drafts folder in an Archive PST file and not having a Deleted Items folder associated with an Inbox were part of the same problem or I would not have mentioned the Drafts folder issue since I have an easy work-around. Perhaps my question should have been: How to I load emails from an IMAP account and be able to delete the spam?

    Read the article

  • Fetch videos from sony handycam to linux

    - by bstpierre
    I've got a Sony Handycam DCR-DVD101. When I plug connect the USB cable to my laptop (Ubuntu 10) it doesn't mount any storage device. If I run usb-devices, I see: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=00c1 Rev=01.00 S: Manufacturer=SONY S: Product=Storage Device C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage The driver says usb-storage, but I'm not sure how to get the device mounted. Is there a way to make this work? Update: checking dmesg, I see: [259072.576559] usb 2-1.1: new high speed USB device using ehci_hcd and address 6 [259072.687200] usb 2-1.1: configuration #1 chosen from 1 choice [259072.836188] Initializing USB Mass Storage driver... [259072.836476] scsi5 : SCSI emulation for USB Mass Storage devices [259072.836632] usb-storage: device found at 6 [259072.836636] usb-storage: waiting for device to settle before scanning [259072.836660] usbcore: registered new interface driver usb-storage [259072.836666] USB Mass Storage support registered. [259077.830410] usb-storage: device scan complete [259077.832343] scsi 5:0:0:0: CD-ROM SONY DDX-A1010 R1.0 PQ: 0 ANSI: 0 [259077.888167] sr1: scsi3-mmc drive: 0x/0x pop-up [259077.888446] sr 5:0:0:0: Attached scsi CD-ROM sr1 [259077.888593] sr 5:0:0:0: Attached scsi generic sg2 type 5 [259080.002079] sr 5:0:0:0: [sr1] Unhandled sense code [259080.002085] sr 5:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [259080.002091] sr 5:0:0:0: [sr1] Sense Key : Blank Check [current] [259080.002097] sr 5:0:0:0: [sr1] Add. Sense: No additional sense information [259080.002104] sr 5:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 00 00 [259080.002117] end_request: I/O error, dev sr1, sector 0 [259080.002123] Buffer I/O error on device sr1, logical block 0 [259080.002128] Buffer I/O error on device sr1, logical block 1 Those I/O errors don't look good, is there any hope?

    Read the article

  • How can I get WAMP and a domain name to work on a non-standard port?

    - by David Murdoch
    I have read countless articles on setting up a domain on WAMP to listen on a port other than 80; none of them are working. I've got Windows Server 2008 (Standard) with IIS 7 installed and running on port 80 (and 443). I've got WAMP installed with the following configuration. Listen 81 ServerName sub.example.com:81 DocumentRoot "C:/Path/To/www" <Directory "C:/Path/To/www"> Options All MultiViews AllowOverride All # onlineoffline tag - don't remove Order Allow,Deny Allow from all </Directory> localhost:81 works with the above configuration but sub.example.com:81 does not. Just to make sure my firewall wasn't getting in the way I have disabled it completely. My sub.example.com domain is already pointing to my server and works on IIS on port 80. Also, if I disable IIS and change the Apache port from 81 to 80 it works. Yes, I am restarting Apache after each httpd.conf change. :-) I don't need any other domain (or sub domains [I don't even care about localhost]) configured which is why I'm not using a VirtualHost. Any ideas what is going on here? What could I be doing wrong? Update Changing Listen to 80 but keeping ServerName as sub.example.com:81 causes navigation to sub.example.com:80 to work; this just doesn't seem right to me. Could ServerName be ignoring the :port part somehow? netstat -a -n | find "TCP": >netstat -a -n | find "TCP" TCP 0.0.0.0:81 0.0.0.0:0 LISTENING TCP 0.0.0.0:135 0.0.0.0:0 LISTENING TCP 0.0.0.0:445 0.0.0.0:0 LISTENING TCP 0.0.0.0:912 0.0.0.0:0 LISTENING ... TCP 127.0.0.1:81 127.0.0.1:49709 TIME_WAIT ...

    Read the article

< Previous Page | 710 711 712 713 714 715 716 717 718 719 720 721  | Next Page >