Search Results

Search found 20442 results on 818 pages for 'software evaluation'.

Page 719/818 | < Previous Page | 715 716 717 718 719 720 721 722 723 724 725 726  | Next Page >

  • LDAP Account Locked Out Sporadically after Password change - Finding the source of invalid attempts

    - by CityView
    On a small network of machines (<1000) we have a user whose account is being locked out after an indeterminate interval following a password change. We are having severe difficulties finding the source of the invalid logon attempts and I would appreciate it greatly if some of you could go through your thought process and the checks you would perform in order to fix the problem. All I know for sure is that the account is locked out several (5+) times a day, I can't even be sure it's due to failed login attempts as there is no record of failure until the account is locked. So far I have tried; Logging the account out of everything we can think of and back in with the new password Scanning the user's box for any non standard software which might perform an LDAP lookup Checking all installed services on our production boxes to check none are attempting to run under the account Changing the user back to their old password (Problem persists so perhaps password change is a red herring) Wireshark on a box where lots of LDAP authentication is performed - Rejects only occur after account is already locked out Clearing the credential cache in - Control Panel - User Accounts - Advanced Looking at the local I'm at a loss for what to try. I am happy to try any suggestions you have in order to diagnose the issue. I think my question boils down to a simple request; I need a technique for deriving the source (Application/Host) of the invalid login attempts which are causing the account to be locked. I'm not sure if that's even possible but I suspect there must be more I can try. Many thanks, CityView

    Read the article

  • How do I fix error 1303 during TI Connect install?

    - by smoth190
    I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

    Read the article

  • Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

    - by clem
    Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

    Read the article

  • Freebsd jail for an small company - checklist - what shouldn't forget

    - by cajwine
    Looking for an checklist for an "small company freebsd/jail server". Having pretty common starting point: FreeBSD jail (remote/headless) for the company: public web, email, ftp server, and private (maybe in the future partially public) wiki (foswiki) 4 physical persons, (6 email addresses) + one admin - others will never use ssh) have already done usual hardening on the host side (like pf, sshguard etc). my major components are: dovecot, exim, apache22, proftpd, perl5.14. Looking for an checklist, what I shouldn't forget. My plan: openssl self-signed certificates for exim, dovecot and proftpd (wildcard keys) openssl self-signed certificate for apache (later will go for "trusted-signed" key) My questions are: is is an "good practice" having one pair of wildcard SSL-certificates for many programs? (exim, dovecot, proftpd) - or should I generate one key for each service? should I add all 4 persons as standard (unix) users, or I should go with virtual users? Asking because: have only small count of users, and it is more simple to configure everything (exim, dovecot) for local users ($HOME/Maildir), plus ability to set $HOME/.forward/vacation and etc. is here some (special) things what I should consider? (e.g. maybe, in the future we want setup our own webmail - will make this any difference?) any other recommendation? Thank you, hoping that this question fit into the http://serverfault.com/faq under the: Server and Business Workstation operating systems, hardware, software Operations, maintenance, and monitoring Looking for an checklist, but please explain why you're recommending it. See Good Subjective, Bad Subjective. related: What's your suggested mail server configuration for a FreeBSD server?

    Read the article

  • Connect trough remote computer connection

    - by Didac
    First, sorry for my english and my poor knowlodge of this subject. I have a dedicated server placed in Germany (windows 2008 R2) and I live in spain. I would like to access internet from my home computer (Windows 7 Pro x64), trough my server in Germany, so I can use a German IP, what I need some times. I have complete acces in to both computers, but I just don't know where to start. (My knwoledge is limited to software development :/ ) I'd like to know where to start, if I need to create a VPN and so.. Thanks in advance! Update 1 I tried a lot of options of OpenVPN, but I sadly I know nothing abuot networking, so I have to accept I do not know what I'm doing :( Here are my config files (note most of the options are from the sample config files). server.conf #server config file start port 1194 proto udp dev tun server 10.0.0.0 255.255.255.224 #you may choose any subnet. 10.0.0.x is used for this example. ca "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\server.crt" key "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\server.key" dh "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\dh1024.pem" push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" #the following commands are optional keepalive 10 120 comp-lzo persist-key persist-tun verb 5 #config file ends client.conf #client config file start client dev tun proto udp remote 176.9.99.180 1194 resolv-retry infinite nobind persist-key persist-tun ca "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\client1.crt" key "C:\\Program Files (x86)\\OpenVPN\\easy-rsa\\keys\\client1.key" ns-cert-type server comp-lzo verb 5 explicit-exit-notify 2 ping 10 ping-restart 60 route-method exe route-delay 2 # end of client config file And here's the server's network settings: IP address: 176.9.99.180 Subnet mask: 255.255.255.224 Default gateway: 176.9.99.161 Preferred DNS server: 127.0.0.1

    Read the article

  • Internet Troubles - PPPoE vs PPPoA?

    - by AkkA
    I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

    Read the article

  • Power issues Foxconn Barebones kit

    - by alpha1
    I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

    Read the article

  • Should I embed the sRGB color profile in JPEG files?

    - by basic6
    I have a large (growing) collection of scanned images. They are TIFF files, mostly 48 bit with the Adobe RGB color space. This color profile is integrated in the files. When such a file is opened in IrfanView (with plugins), it says (Image - Information) Adobe RGB 1998. "Normal images", like the JPG files from a digital camera, do not (necessarily) have a color profile integrated in the file. I understand that it's necessary to include the Adobe RGB profile in an image file which uses the Adobe RGB space, so the color values can be interpreted correctly. Here's a test image with a completely different color profile, programs that ignore the included profile (like MSIE8 or Gwenview) will render it as sRGB (?): I'm planning to convert my TIF files to JPG, so I'm wondering if there's anything wrong with using IrfanView that would save them as sRGB without embedding the sRGB profile. I've heard that images should always be saved with the color profile included. Since every image seems to be interpreted as sRGB by default (by software without color management), I don't understand why the sRGB profile should be included?

    Read the article

  • Disk wipe preferences

    - by hmvm123
    I manage a pool of systems that are loaded with software and sent to potential customers for evaluations which often land sensitive information on the drives. Before shipping them back, they typically like a standard wipe to be run to clean out the drives. Most are familiar with DBAN so I try to make sure it can work on my systems. Unfortunately, this means I'm usually in RAID driver hell trying to make sure that the versions out there support the ones my systems are shipping with. These are various kinds of 3ware and LSI ones. Consequently, I have DBAN 1.0.7 working on some, a beta version of 2.0 on the others and 2.2.6 on some of the latest SSD based ones. Now with the LSI controllers on my IBM x3550 M3s (1064/1068) I'm getting no love at all. Is there a way out? Do you buildroot with DBAN and try to piece the drivers together? Any other tools, free or commerical, that stay updated. I'm trying to walk people of varying technical proficiencies through this, so a boot disk with simple choices is preferable.

    Read the article

  • E-mail duplication problem

    - by Gavin Osborn
    I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

    Read the article

  • Converting PDF eBooks into a Kindle format

    - by Ender
    Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this? EDIT: I've tried Calibre, and have checked their forums to play with some of the advanced settings, yet the solutions available seem to be extremely poor, especially if the book you're attempting to read contains equations, code, or anything outside of plain text. I've also tried Amazon's conversion service, which wasn't much help with such documents. The best way I have found so far is to build the entire thing over again in ePub or RTF format and convert to MOBI from there. This works for text-heavy books with tables, but anything technical still isn't covered. Can anyone help with this?

    Read the article

  • Production deployment to EC2 with minimal downtime

    - by jensendarren
    I have a simple web application deployed on a large instance with EC2. I now want to deploy the latest code to this server but I want to do this in a way which minimizes downtime and is a smooth as possible for the end user. Here is my plan: Fire up another large instance Install all the software layers on that instance Restore and attach an EBS drive to the instance Deploy our latest production ready code on the new instance Run all tests (including manual testing of the application) (If tests pass) Put a "Site Under Maintenance" notice on the live site. Backup the EBS instance on the live site Detach the EBS instance from the new server and replace with the latest backup Use ec2-associate-address to move the IP address to the new instance Sit back and wait for traffic to start flowing though the new instance Terminate the old instance Does this seem like a good strategy? Are there any tutorials or books that might cover this topic? I have already read Cloud Application Architectures by George Reese, which is an excellent book, but does not cover deployment. Additionally, I know that there are tools that can help with this like RightScale or enStratus which I will use when I start using more than one instance.

    Read the article

  • Recover data from Dynamic Disk (MBR) bigger than 2TB

    - by Helder
    Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

    Read the article

  • Erratic WiFi 2.4 GHz channel spikes, what gives?

    - by Francis W. Usher
    Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

    Read the article

  • Can Octopussy use messages other than syslog style?

    - by Lee Lowder
    I am currently exploring different options for a centralized log server. We use both Linux (Ubuntu 10.04 / 12.04, LTS for both) and Windows, though for this specific issue only Linux is relevant. I like the interface that octopussy has and it's feature list, but I am hesitant due to a few things. One of the biggest concerns I have is that it seems to be syslog only. The end goal is to have a centralized place for our devs and admins to be able to search through the logs generated by Apache, Tomcat and 70+ web apps spread out among a cluster, for both our prod and test environments. While I did see that octopussy has support for plugins, I haven't been able to find any sort of plugin repo or in depth guides as to what can be done with them. Does anyone know if plugins can be used to allow octopussy to non-syslog messages? Specifically log4j type log messages that may include multi-line stack traces and such. Also, is there a user community for this software, such as a mailing list or forum? I've been unable to locate any so far. Thank you.

    Read the article

  • Create a PDF that defaults to flip on short edge when printed double-sided

    - by user568458
    We're creating a 2-page PDF brochure with a target audience who will print it on their regular office or home printers. If it is printed on a double-sided printer (common in offices), it'll come out correctly if set manually by the user to "Flip on short edge", but will come out with the second page upside down if default settings are used (flip on long edge). Our target audience aren't very tech-literate, and we've found that even within our own office network there is variation in the location of the 'Flip on short edge' setting - so it isn't realistic to give everyone who downloads the PDF instructions on how to change this setting or to expect everyone to find out how to change the setting off their own backs. So, when creating a PDF (ideally using Adobe InDesign or Acrobat, but if other software or hacking is needed that's fine...), is there a way to configure the PDF file itself so that when printed double-sided with default settings, it flips on the short edge? If possible, it'll be useful supplementary info to know how reliable any such methods are across different PDF readers (e.g. Adobe Reader, Acrobat, Mac Preview, inbuilt browser readers (e.g. chrome), FoxIt, etc). If questions about content creation like this aren't a great fit here, feel free to migrate it to the graphic design stackexchange site - this question seems to fall half way between the two sites

    Read the article

  • Webcam becomes "Unknown Device" after Windows Messenger 2011 is installed

    - by Boris
    I have Sony VAIO VGN-NS290J laptop. I installed Windows 7 Ultimate 64-bit. I was able to find drivers for all hardware without any problems. Recently, I installed Microsoft Windows Live Essentials 2011, i.e. Windows Live Messenger 2011. Ever since that application is running on my computer, my webcam is not recognized by the OS any more. It is listed as the "Unknown Device" and placed in the Universal Serial Bus controllers group in the Device Manager. There don't seem to be any drivers for this webcam. It's a standard Sony Motion Eye web camera and Sony does not offer any drivers for it. There is one application to download that utilizes the camera, but there are no drivers (and the system is showing the same behavior regardless of the presence of the application). It happens from time to time that the webcam becomes recognized by the OS again, after a couple of restarts; but not always. Then it becomes unknown again. I am absolutely positive that this issue is caused by the Windows Live Messenger 2011, because same symptoms caused the same effects before. I wish to be able to continue to use this software, but also to use my webcam. I was wondering if anyone had a similar issue and if there is a way to fix it. Thanks for all the help, I appreciate it. Update: I have discovered a pattern - if the camera goes astray, restarting the machine does not bring it back; but switching the computer off and turning it back on does. Every time! This is getting super complicated :)

    Read the article

  • Encrypted folders and files stay encrypted when copied

    - by user66126
    Hi all, I just tried out Windows 7 feature to encrypt a folder. I found that when I access the encrypted folder from another computer (the parent folder of the encrypted folder is shared) I can see the files there but I could not open it (which is good). But when I copy the file to another folder outside the encrypted folder (regardless it is on the same remote computer or to the computer from where I am accessing the files) then I can open the file without any problem. This might be how it works ... but that's not what I need. My question is: Can I encrypt a folder (and all files inside), access those files (create, edit) seamlessly while I am logged in normally to the computer ... but make the files stays encrypted when they were copied to another directory outside the encrypted folder? Regardless they were copied to the same computer or another computer or uploaded to a remote server. If this is not a feature that Windows natively support, is there third party software that does that? Thank you.

    Read the article

  • Password-less login into localhost

    - by Brad
    I am trying to setup password-less login into my localhost because it's required for a tutorial. I went through the normal steps of generating an rsa key and appending the public key to authorized_keys but I am still prompted for a password. I've also enabled RSAAuthentication and PubKeyAuthentication in /etc/ssh_config. Following other suggestions I've seen, I tried: chmod go-w ~/ chmod 700 ~/.ssh chmod 600 ~/.ssh/authorized_keys But the problem persists. Here is the output from ssh -v localhost: (tutorial)bnels21-2:tutorial bnels21$ ssh -v localhost OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to localhost [::1] port 22. debug1: Connection established. debug1: identity file /Users/bnels21/.ssh/id_rsa type 1 debug1: identity file /Users/bnels21/.ssh/id_rsa-cert type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 1c:31:0e:56:93:45:dc:f0:77:6c:bd:90:27:3b:c6:43 debug1: Host 'localhost' is known and matches the RSA host key. debug1: Found key in /Users/bnels21/.ssh/known_hosts:11 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/bnels21/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Offering RSA public key: id_rsa3 debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /Users/bnels21/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Any suggestions? I'm running OSX 10.8.

    Read the article

  • Imac g5 with no OS nor CD drive

    - by sinekonata
    What I want: Ubuntu on a g5 Imac. What I have: An empty PC (Intel g5 17" Imac) with broken CD drive. Its model is A1173. This PC with Ubuntu 12.04 and an old Vista partition. a usb flash drive. Problems: No CD means the only boot Drive I could use is USB. There are no BIOS on Macs so I can't set boot settings or even see if it detects my USB drive. When I start the machine and press ALT the first and only thing I see is an old corrupted winXP partition and not a single option or additional information. So assuming blindly that the Mac hardware/firmware works normally, I don't have any Mac OS to use any of the tools that I found on different tutorials for building a bootable .img drive for macs. I can't find much software on Linux/Windows to substitute to those tools, for example among others converting an .iso file (win/linux) to .img (mac I guess). Which makes me think that the scenario where someone like me has Mac hardware but no Mac OS is extremely rare. So other than finding someone that has a Mac I have no solution. So I ask what would you do? the only thing is it should not involve any money (I know mac soft is rarely free) which also excludes getting any MacOS unless I can use a free macos.img for VM or restore the original Mac for free. Thank you

    Read the article

  • How to record tv to network share with Windows Media Center?

    - by Peterdk
    Well, you would think that Windows 7's new MediaCenter would be up to the task of recording your TV to a network share/drive. Too bad, it looks like it's just not possible. I have a windows 2008 R2 server, and a Windows 7 machine with a TV card. Since my server has 2TB of storage, it would be nice to record directly to it's networked drive. (I mounted it as Z:). I tried the following: Selecting it in Media Center Itself: Not working. Not available. Editing the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Service\Recording , setting RecordPath to Z:\TV. Not working. Editing the registry: setting RecordPath to \\server\TV. Not working. Creating a Symlink (mklink \D) to Z:\TV and \\server\TV and setting that in the registry as RecordPath. Currently I am out of options. I could ofcourse Install Windows7 on my server, but I have no license for that, and my windows 2008 r2 is free from dreamspark. Are there people that are succesfully recording to a networked drive/storage? edit I also need to mention that I need to be able to acces the stored files from other PC's, like my laptop. So iSCSI is great for recording, but it looks like you can't access iSCSI devices from multiple PC's. Looks like sharing a iSCSI device is out of the question, so: Are there workarounds to get this thing recording to my network drive?

    Read the article

  • All of the NTFS hard links damaged, where are hardlinks stored and how to recover them?

    - by String Xu
    This is Windows 7 x64 sp1 on a NTFS file system. All hardlinks within C:\Windows\System32 folder disappear, and the Windows can't boot, because even the osloader, C:\Windows\System32\boot\Winload.exe also disappeared. Nevertheless, the original files are still located in the corresponding C:\Windows\winsxs folders. After booting into the Recovery Environment, and copied one Winload.exe (x64) from other folder, Windows gave an error pointing out that "ntoskrnl.exe is corrupted or missing...its file digital signature cannot be verified" In trying to boot in Safe Mode, the message above was shown after a screen prompting "Loaded \Windows\system32\config\system" Because at this early booting stage, smss.exe was still not loaded, so there is not any dumping and logs. Based on my study, ntoskrnl.exe depends on the following files: C:\windows\system32\PSHED.DLL C:\Windows\System32\hal.dll C:\Windows\System32\kdcom.dll C:\Windows\System32\clfs.sys C:\Windows\System32\ci.dll All those files above are copied from their corresponding folders and verified their md5 with a well-operating Windows 7 x64 SP1. But the booting error is still the same: "ntoskrnl.exe is corrupted or missing..." Background: 1. Before the reboot, there was an windows update going on. Then something unknown happen, almost all processes were broken to run, including the windows task manager, taskmgr.exe. After mount the hard disk to other computer, it seems that all hardlinks within C:\Windows\System32 folder were gone. I tried several data recovery software, but they are not be able to find those disappeared NTFS hard links. So the question is: Where are information about those hard links stored? And how to recover them? Are they depend on some windows service or stored in the registry?

    Read the article

  • RAID 6 that can read with least 1000 Mbit/s?

    - by Diblo Dk
    I purchased a Dell PERC 6/i which I expected to be able to read with 1000 Mbps. There is not much to do now, but there are some things I wanted knowledge about for another time. I have configured it with four 2 TByte drives and RAID 6. It have 256 MByt ram and transfer rate of 300 Mbps. The benchmark test showed: Min read rate: 136.3 Mbps Max read rate: 329,6 Mbps Avg read rate: 242,2 Mbps What could I had done to get at least 1000 Mbps? Is it normal for internal and external RAID controllers to have a lower transfer rate eg. 300 Mbps? (I did not noticed at the time that it was not 3 Gbps) How would a RAID 10 had performed compared to RAID 6 or 5? Would it have been better to use software RAID (Linux) with the internal 3 Gbps SATA controller? UPDATE: The drives is SATA III 6 Gbps. http://www.seagate.com/files/staticfiles/docs/pdf/datasheet/disc/desktop-hdd-data-sheet-ds1770-1-1212us.pdf (2TB)

    Read the article

  • How can visiting a webpage infect your computer?

    - by Cybis
    My mother's computer recently became infected with some sort of rootkit. It began when she received an email from a close friend asking her to check out some sort of webpage. I never saw it, but my mother said it was just a blog of some sort, nothing interesting. A few days later, my mother signed in on the PayPal homepage. PayPal gave some sort of security notice which stated that to prevent fraud, they needed some additional personal information. Among some of the more normal information (name, address, etc.), they asked for her SSN and bank PIN! She refused to submit that information and complained to PayPal that they shouldn't ask for it. PayPal said they would never ask for such information and that it wasn't their webpage. There was no such "security notice" when she logged in from a different computer, only from hers. It wasn't a phishing attempt or redirection of some sort, IE clearly showed an SSL connection to https://www.paypal.com/ She remembered that strange email and asked her friend about it - the friend never sent it! Obviously, something on her computer was intercepting the PayPal homepage and that email was the only other strange thing to happen recently. She entrusted me to fix everything. I nuked the computer from orbit since it was the only way to be sure (i.e., reformatted her hard drive and did a clean install). That seemed to work fine. But that got me wondering... my mother didn't download and run anything. There were no weird ActiveX controls running (she's not computer illiterate and knows not to install them), and she only uses webmail (i.e., no Outlook vulnerability). When I think webpages, I think content presentation - JavaScript, HTML, and maybe some Flash. How could that possibly install and execute arbitrary software on your computer? It seems kinda weird/stupid that such vulnerabilities exist.

    Read the article

  • How to increase the speed between two external hard drives on my laptop?

    - by Roman
    Hello, I own Sony Vaio Z laptop with two external USB ports. It's quite new and has USB 2.0 support. I'm using Vista x64 on it. I also have two external usb hard drives, Iomega 500GB and WD for 1TB. Every hard drive has USB 2.0 support. I connect two devices to my laptop and trying to copy date from one hard drive to another. But it takes a lot of time! The speed is about 15 Megabytes per second. I have to wait toooooo long to copy all the information from one hard drive to another. When I try to copy information from my internal (SSD) hard drive, it works fine for both external drives. The speed is very high and it shows me something about 100 Megabytes per second. It makes me feel that USB 2.0 is OK on both drives. But when I'm trying to copy from one external drive to another external, I still get very low speed. I checked out Device Manager and here is the settings I have: (sorry, can't upload image because of my rating, check this url: http://picbite.com/image/122073daljo/ ) I think it's because two of my external drives use the same USB 2.0 controller. Is there any way to make it work faster? Is it possible to move one of my USB ports to other USB 2.0 controller? Or is there any software which can help me to automate copying all the files thru my internal drive? I have only about 3 gigabytes free space on internal drive and it's quite difficult to move manually every file from one hard drive to internal and then again to another internal.

    Read the article

< Previous Page | 715 716 717 718 719 720 721 722 723 724 725 726  | Next Page >