Search Results

Search found 31206 results on 1249 pages for 'version detection'.

Page 721/1249 | < Previous Page | 717 718 719 720 721 722 723 724 725 726 727 728  | Next Page >

  • Load-balancing between a Procurve switch and a server

    - by vlad
    Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

    Read the article

  • Running OLEDB VB6 Windows Progam Under Wine

    - by Beaner
    I'm trying to install a VB6 Windows program that uses OLEDB to access VFP tables to run under Wine 1.0.1 on Ubuntu 9.10. Wine is configured to Windows version Windows XP. The program install ran okay, and I used winetricks to install MDAC 2.8 and JET 4.0 sp7. I also installed Microsoft's vfpoledb and vfpodbc drivers. The application starts and displays an error message, item cannot be found in the collection corresponding to the requested name or ordinal. Does anyone have an idea how to fix this?

    Read the article

  • Mouse scroll wheel in Citrix

    - by molecule
    Hi all, One of my users is experiencing a problem whereby the mouse scroll does not work on the Citrix published application. I have tried to install mouse drivers on his local PC as well as swapping the USB with a PS/2 mouse but still no go. I have researched this issue for a few days but have not been able to find a fix. PC is running Windows XP and ICA client is version 10 I am pretty sure its a problem local to that PC since every other user using the application published on the same server are not having any issues. What could it be?

    Read the article

  • Starting phusion passenger on working apache

    - by fl00r
    Hi! I've got Apache (-v): Server version: Apache/2.0.63 Server built: Nov 29 2009 15:23:34 Cpanel::Easy::Apache v3.2.0 rev4899 I want to start new Sinatra application on passenger. I've just installed passenger gem. So now I need to set up apache configuration. In httpd.conf there are many settings of others applications on server. So I just can't reinstall apache with passenger-install-apache2-module. I need to set up exist Apache with passenger. What have I do now?

    Read the article

  • hp smart array lock up code 0x15, what is that? (or where can I get a list of descriptions of HP smart array controller lock up codes)

    - by user47650
    Hi, I've had a couple of Dl180 6g boxes hung over the last week, each have a P410 smart array controller. upon reboot the server has indicated that a controller failure event occurred and the previous lock up code was 0x15 - the server rebooted without issue. However there was nothing in the IML log, but the ADU report provided the following; Trap Address High Or Post Results Lockup Reason Or Post Error RIS Updates Or Post Error Detail Firmware Version Trap Address Low 0x8087 0x0015 0x0000033e 0x015e 0xd65c any suggestions on what that code is, my google fu failed. And hp support have not responded with any detail as yet.

    Read the article

  • Is it safe to disable nmi_watchdog?

    - by Rayne
    I'm using RHEL 6 (kernel 2.6.32-131) and I'm trying to start oprofile, but I keep getting an error. My oprofile version is 0.9.6-12. I was able to successfully do opcontrol --init But when I did a opcontrol --start --no-vmlinux I got the error Using default event: CPU_CLK_UNHALTED:100000:0:1:1 Error: counter 0 not available nmi_watchdog using this resource ? Try: opcontrol --deinit echo 0 > /proc/sys/kernel/nmi_watchdog I don't know if it's safe for me to do this? For what I googled, it seems that nmi_watchdog is used to reboot the system if it hangs, and that sounds like something I want. Also, grep NMI /proc/interrupts shows a bunch of numbers, which I guess indicates that nmi_watchdog is already running? How can I run both oprofile and nmi_watchdog?

    Read the article

  • Error in joining 4 AVI files.

    - by goldenmean
    Hello, I have 4 avi files. Each file can be played properly in VLC player, Windows media player. Video-Audio Codec type in each of this avi file is Xvid-Mpga. I used below avi joiners: Quick AVI joiner, AVI join, BoilSoft Video Joiner(trial version), but all of them gave an error when i select the first part avi file saying : "format of the part1.avi file cannot be recognized".. What could be the problem. How do i join these AVI files. Any pointers will help. Thanks. -AD.

    Read the article

  • Centos livecd of current installation

    - by mplacona
    I'm trying to create a liveCD of my current Centos installation. i want it to be almost like a backup, so whenever I want to copy my current installation to another computer I would simply install from my custom liveCD. I know this is possible, and found some resources in the nets, but they all seem to only create a minimal version of CENTOS, and I'm wanting to have all the current functionalities available to me at present, including all of my development functionalities, Apache and samba settings, etc. I have done (on Debian though) it a few years ago, but can't remember how. could anyone please shed me a light on this? Thanks in advance

    Read the article

  • How to open ports on modem for better torrent performance

    - by Mehper C. Palavuzlar
    I've been using utorrent to download and upload torrents for a long time. Recently someone told me that I need to open port(s) for utorrent from my modem settings for better downloading and uploading performance. Is it true? If yes, how can I do that? My utorrent version: 2.0 and the port used for incoming connections: 61829. My modem: Yaksu S200 ADSL router modem and I can reach its settings via web interface. I looked at the settings but they seem a bit complicated to me. Other info you may need to know: I have dynamic IP. I'm using Win7 x64.

    Read the article

  • Snow Leopard tzdata

    - by pgb
    I live in Argentina, and our DST rules change often. So often, that major OS' tend to ship with an old version of tzdata DBs. In the past, I successfully updated the time zone databases in Tiger and Leopard. Today, however, when trying to update it in Snow Leopard, it did not work. Not only it failed, but now even after I reverted my changes, there seems to be some "cache" where the time zone information was retained. The files I updated (and reverted) are located at: /usr/share/zoneinfo and /usr/share/icu. To update those, I grabbed Apple's source code for ICU and recompiled it's database using the latest tzdata file (2010b). Then, I recompiled the tzinfo by running zic, and copied all the files to the system folders. Does anyone have experience dealing with Snow Leopard's timezone DB and can help? Thank you.

    Read the article

  • Vista Startup Repair cannot repair my Toshiba Laptop (L300D)

    - by tdot
    I installed some updates, and now the computer doesn't boot up, it just keep's telling me to go to repair, which doesn't fix the problem. I see the BSOD on startup, but it flashes by too quick. (I also don't have Vista on DVD to do a reinstall if I need to) This is what I get from the Startup Repair details Problem Event Name StartupRepair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 2 Problem Signature 04: 131074 Problem Signature 05: BadDriver Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6001.2.1.0.256.1 Local ID: 1033 Any help will be appreciated. Thanks.

    Read the article

  • "The site's security certificate is not trusted!" on every SSL page?

    - by Isaac Waller
    I'm using the latest Chrome dev build on Mac OS X. Recently, I've been getting this message on any HTTPS webpage when I visit it the first time: The site's security certificate is not trusted! You attempted to reach checkout.google.com, but the server presented a certificate issued by an entity that is not trusted by your computer's operating system. This may mean that the server has generated its own security credentials, which Google Chrome cannot rely on for identity information, or an attacker may be trying to intercept your communications. You should not proceed, especially if you have never seen this warning before for this site. Why is this here, and how can I fix it? It may be because of my development build, but many other people use the dev version also, and I expect it would be fixed quicker then this.

    Read the article

  • Cannot uninstall Office Live Add-in 1.4 after installing Office 2010

    - by Shevek
    Last night I upgraded to Office 2010 RTM from MSDN. I'm now trying to uninstall the Office Live Add-in that I used with Office 2007 as this functionality is built in to Office 2010. When I run the uninstall from control panel I get the following message: Microsoft Office Live Add-in cannot be installed because you do not have the right version of Microsoft Office installed on your computer Google has pointed to 2 solutions, both of which are pretty useless: Use the MS Windows Installer Cleanup - this is not good because all it does is remove the Installer entry from the registry, leaving all the installed files behind Uninstall Office 2010, uninstall Add-in, reinstall Office 2010 - that is just rediculous, but typical MS response So, can I get this off my system without resorting to option 2?

    Read the article

  • How to setup VIM for php development?

    - by Ashwin kumar
    I have been trying a lot (but not smartly) to figure out setting up VIM, ctags, omnicomple for PHP development. On Googling I found this file. But have no clue how to use it. What have I done until now? Here it is: I am on Fedora 17 64-bit OS Logged in as root Found my VIM version to be VIM - Vi IMproved 7.3 (2010 Aug 15, compiled May 8 2012 15:05:51) Followed the install details as here http://www.vim.org/scripts/script.php?script_id=3171 install details Place in $HOME/.vim/autoload/phpcomplete.vim and enable the php ftplugin What else I am missing? How do I start using omnicomplete. (this is the first time I am using omnicomplete) Why didn't I try IDE's? I have a single core machine running LAMP stack. Didn't wanted to slow down everything and hence sticking to command line environment.

    Read the article

  • Trying to install pdo_oci via PECL fails asking for PDO extension

    - by Igoru
    I'm using Linux Mint 11 (based on Ubuntu 11.04) and I need to use PHP with Oracle through PDO, a requirement of the framework we will work with. I've installed various PDO extensions using the normal apt-get method, like php5-mysql, etc, and they loaded just fine, along with the initial PDO extension. But there's no package for Oracle bindings. So, when I try to run sudo pecl install pdo_oci it throws me this: WARNING: "pear/PDO_OCI" is deprecated in favor of "channel://http://www.php.net/pdo_oci/ext/pdo_oci" pear/PDO_OCI requires PHP extension "pdo" (version >= 1.0) No valid packages found install failed How can I add this channel, or is there a better way to install the PDO_OCI extension?

    Read the article

  • RAR Password recovery / hash extraction on Mac OS X

    - by Josh K
    I'm running Mac OS X 10.6.2 and have been handed a couple of old files that need to be extracted. Old backups or finances or bills I believe. They are RAR files, and password protected. Is there a way to extract the hash from these files so I can feed it into John The Ripper or Cain and Abel? Edit I have downloaded cRARk, but unfortunately nothing I have (SimplyRAR, RAR Expander, The Unarchiver) will extract it without a password. Can someone verify that I'm crazy and there is no password on the Mac version?

    Read the article

  • Using virt-install to mount multiple cdrom drives/images

    - by Dana the Sane
    I would like to create a windows xp guest from the windows xp upgrade cd I have, along with one of a few full versions I have around. However, when I reach the stage in the installer where I am prompted to insert a full version cd, the installer can't find it, i.e.: Setup could not read the CD you inserted, or the CD is not a valid Windows CD.. Is there a work-around for this?, my Googling didn't uncover anything. I've tried various combinations of mounting .iso files and specifying disks, such as: $sudo virt-install --accelerate --connect qemu:///system -n xpsp1 -r 2048 --disk ./vm/winxp_sp1.iso,device=cdrom --disk ./vm/windows.qcow2,size=12 --vnc --noautoconsole --os-type windows --os-variant winxp --vcpus 2 -c /dev/cdrom --check-cpu If I try to specify multiple cdrom drives, I receive an error: virt-install --accelerate --connect qemu:///system -n xpsp1 -r 2048 --disk ./vm/winxp_sp1.iso,device=cdrom --disk /dev/cdrom,device=cdrom --disk ./vm/windows.qcow2,size=12 --vnc --noautoconsole --os-type windows --os-variant winxp --vcpus 2 --check-cpu Starting install... ERROR IDE CDROM must use 'hdc', but target in use.

    Read the article

  • What is the difference betweeen "Network install" and "Network Boot" options in virt-manager when installing a new virtual machine

    - by Marwan
    From my understanding of PXE (Preboot Execution Environment), I know that there must be some negotiation first between the booting client and a DHCP server to obtain network parameters (IP address, etc) in order for the client to be able to fetch the boot loader and kernel image from the boot server. In other words, and aside from being a "virtual" machine, we're talking here about a "bare metal" machine, so there must be some "pre boot" mechanism for those negotiations to take place, and this is exactly what PXE is all about. When I think about the "Network install" option, I can't figure out how the new VM would be able to fetch the boot images (bootloader and kernel) without the previously mentioned mechanism. So, here is a short version of the question: When provisioning a new virtul machine, how do you expect the "Network install" option in virt-manager to work behind the scenes? Many thanks.

    Read the article

  • CentOS 5.8 server, installed Web Server vs yum install httpd

    - by Shiro
    I would like to know, what is the different between, the build-in CentOS server web server vs I install manual with yum install httpd I am new in CentOS. I just installed my CentOS 5.8 Server with Web Server checked. With some Google Search with LAMP installation, they listed with yum install httpd I had check inside /etc/init.d/ already had httpd I try to run yum install httpd http-devel It shows not yet installed. What will happen if I install yum version? What should I do? What is the best practise? Should I remove the Web Server install by default with CentOS? My goal is install LAMP (PHP v5.2.17).

    Read the article

  • Installing sun-java6-jdk with apt-get on Ubuntu 10.04

    - by Adam S
    I have followed the instructions on numerous pages, such as this, which say to run the following commands: sudo add-apt-repository "deb http://archive.canonical.com/ lucid partner" sudo apt-get update sudo apt-get install sun-java6-jdk However, when I do this I still get the following error: me@mycomputer:~$ sudo apt-get install sun-java6-jdk Reading package lists... Done Building dependency tree Reading state information... Done Package sun-java6-jdk is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package sun-java6-jdk has no installation candidate I realize Java is available from many other sources, but for reasons that I can't get into here I must use this specific version. What can I do to get this installed?

    Read the article

  • Macbook Pro suddenly lagging video playback + Flash sites

    - by Mathias
    I have a Macbook Pro, OSx Lion, Intel Core2 Duo, 4GB Ram, NVidia Geforce 8600M GT 128 MB Ram, Intel x25m SSD. Approximately 4 years old. I've been running Flash sites and playing videos without any problems for years. Then suddenly 3 months ago, a flash site like http://thefwa.com is lagging in all browsers. Even mouseover animations - anything. Also video playback in e.g VLC and Quicktime is now lagging. Same videos I used before, I tried installing an older version of VLC without any luck. Playing back video in VLC utilizes the CPU almost 100%, and Flash sites like thefwa.com easily takes up 50-60%. It's as if the hardware acceleration stopped working, or the GPU lost its magic. UPDATE: Same issues also occurred on Snow Leopard Has anyone experienced something similar, or do you know what might be wrong?

    Read the article

  • Outlook receives winmail.txt attachment instead of Excel, PowerPoint or Word attachments from Lotus notes senders

    - by Philippe
    Ok so the title pretty much says it all. We are offering a Hosted Exchange solution for our customer. Everything is working fine except for one customer complaining that he is receiving winmail.dat or winmail.txt attachments instead of the actual Word Excel or PowerPoint attachments he should be receiving, only when these messages come from a specific European senders, that is using Lotus Notes. I know that usually the problem is coming from Outlook senders to other mail clients, but this is not the first they inform me of this but I can't find anything on the matter so far. Has anyone ever gotten and solved this problem? If not, does anyone have any idea regarding this? I had solved this problem a few months ago, by upgrading Outlook to SP2 and then uninstalling it using the Service Pack removing tool of Microsoft. It seems that only the latest SP1 version could work but not the SP2. The problem is that now nothing is working at all. Thank you for your help, Philippe

    Read the article

  • How can I provide secure web content to mobile devices that can't access an intranet?

    - by evanmcd
    I'm working with a client on development web content for their intranet. We want users to be able to access a version of the content on their mobile devices, but most of them don't have the VPN capability to get on to their intranet. I'm wondering if anyone has had experience with this and can recommend a solution. One other thing to consider is that the content is not mission critically secure. If someone outside the company gained access to it, it would not represent a major issue, only a minor annoyance. Thanks for any advice.

    Read the article

  • Why is the XML DTD not found by the browser

    - by hyperuser
    When I load my XML file in a browser, it complains there is 'no style information': "This XML file does not appear to have any style information associated with it. The document tree is shown below." So I wrote an external DTD, then an internal DTD, but keep getting the same 'no style information' error. It doesn't even show the DTD! What am I doing wrong? <?xml version="1.0"?> <!DOCTYPE fotos [ <!ELEMENT fotos (titel,auteur)> <!ELEMENT titel (#PCDATA)> <!ELEMENT auteur (#PCDATA)> ]> <fotos> <titel>titel1</titel> <auteur>jan</auteur> </fotos>

    Read the article

  • The procedure entry php_mb_check_encoding_list could not be located

    - by BlackFire27
    I get this error. The procedure entry php_mb_check_encoding_list could not be located in the dynamic link library php_mbstring.dll The error is related to the php.ini settings, I think.. It finds it difficult to locate the extension I suspect, I put an environment path to the php.exe and its extensions folder, but when I run the command line and call php.exe, that error is being thrown. I use windows. I have got this set in my php.ini. ; On windows: extension_dir = "C:\xampp\php\ext" I installed xampp.. the php version is the latest.. Another thing which is weird is when I try to print out: phpinfo..nothing is being printed out <?php echo phpinfo(); ?> nothing comes out?!?! The question is why and how can I prevent it from being thrown..

    Read the article

< Previous Page | 717 718 719 720 721 722 723 724 725 726 727 728  | Next Page >