Search Results

Search found 45696 results on 1828 pages for 'system componentmodel'.

Page 745/1828 | < Previous Page | 741 742 743 744 745 746 747 748 749 750 751 752  | Next Page >

  • HP DL185 - very slow disk read speed

    - by fistameeny
    Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

    Read the article

  • Hibernate between OS X and Bootcamp Win 7

    - by Willem
    Wouldn't it be great if someone wrote a guide or an app which allowed you to switch instantly between OS X and Windows using Hibernate in both OS:s? Windows 7 already has an option "Hibernate" which allows you to boot back to your OS X partition, but OS X does not exactly offer the same. However, there are possibilities here. It seems that the recent Mac's have 3 different kinds of sleeping mode: Sleep: Low power consumption, RAM still active. Legacy Safe Sleep: No power consumption(?), writes RAM to disk and shuts down (is this the same as Hibernate?) Safe Sleep: Writes RAM to disk and enters sleep mode. If battery level drops too low it goes into Hibernate (is this Hibernate the same as #2 in this list? This is the Hibernate I will be referring to int he rest of this post) It seems that I am unable to force my MacBook Pro (Late 2011) OS X 10.7.3 into a true hibernate using either command line or apps that are supposed to do this. I believe the Mac should show that white loading bar whilst waking up if it was truly put into hibernate (which it does not). But I can get this white bar to show by letting my battery level drop to 0% so there is obviously a system function for it (obviously, duh! :). When Win 7 goes into hibernate it shuts down completely and you can then boot into OS X on startup. On OS X however, hibernate forces you to wake up into OS X. Can you hack this so that you're allowed to select boot partition after OS X hibernates? Would it be possible to use the true hibernate system functionalities of Win 7 and OS X to create a kind of instant switching between the two? Imagine this on a quick SATA-3 SSD like my 180GB Intel 520. Thanks / Willem

    Read the article

  • How do I fix error 1303 during TI Connect install?

    - by smoth190
    I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

    Read the article

  • Moving hidden files/folders with the command-line or batch-file

    - by Synetech
    Question Does anyone know of a way to move files and folders that have the hidden, system, or read-only attribute set from the command-line or a batch file? (No, stripping the attributes first is not an option since there is no practical way to know which attributes were set in order to re-set them after the move.) (Failed) Attempts Using the basic move command does not work with items with the hidden or system attribute set and for some reason, it does not have switches to specify attributes like the dir and del commands do. I tried using a utility I wrote that uses the shell’s file operation function, but that requires using start /w to prevent the batch file from running on ahead, and it complains about long-filename support for some reason. I tried using robocopy, but it first copies the files and then deletes the originals instead of simply moving the source (which results in a frustrating delay, even with the excessive output redirected to nul). (Surprisingly it seems that few people have ever needed to move hidden files from the command-line. All I could find was this one person who abandoned the attempt.)

    Read the article

  • Standards for documenting/designing infrastructure

    - by Paul
    We have a moderately complex solution for which we need to construct a production environment. There are around a dozen components (and here I'm using a definition of "component" which means "can fail independently of other components" - e.g. an Apache server, a Weblogic web app, an ftp server, an ejabberd server, etc). There are a number of weblogic web apps - and one thing we need to decide is how many weblogic containers to run these web apps in. The system needs to be highly available, and communications in and out of the system are typically secured by SSL Our datacentre team will handle things like VLAN design, racking, server specification and build. So the kinds of decisions we still need to make are: How to map components to physical servers (and weblogic containers) Identify all communication paths, ensure all are either resilient or there's an "upstream" comms path that is resilient, and failover of that depends on all single-points of failure "downstream". Decide where to terminate SSL (on load balancers, or on Apache servers, for instance). My question isn't really about how to make the decisions, but whether there are any standards for documenting (especially in diagrams) the design questions and the design decisions. It seems odd, for instance, that Visio doesn't have a template for something like this - it has templates for more physical layout, and for more logical /software architecture diagrams. So right now I'm using a basic Visio diagram to represent each component, the commms between them with plans to augment this with hostnames, ports, whether each comms link is resilient etc, etc. This all feels like something that must been done many times before. Are there standards for documenting this?

    Read the article

  • Under FreeBSD, can a VLAN interface have a smaller MTU than the primary interface?

    - by larsks
    I have a system with two physical interfaces, combined into a LACP aggregation group. That LACP channel has two VLANs, one untagged (the "native vlan") and one using VLAN tagging. This gives us: lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether 00:25:90:1d:fe:8e inet 10.243.24.23 netmask 0xffffff00 broadcast 10.243.24.255 media: Ethernet autoselect status: active laggproto lacp laggport: em1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> vlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=3<RXCSUM,TXCSUM> ether 00:25:90:1d:fe:8e inet 10.243.16.23 netmask 0xffffff80 broadcast 10.243.16.127 media: Ethernet autoselect status: active vlan: 610 parent interface: lagg0 Is it possible to set a 9K MTU on lagg0 while preserving the 1500 byte MTU on vlan0? Normally I would simply try this out, but this is actually on a vendor-supported platform and I am loathe to make changes "behind the back" of their administration interface. This system is roughly FreeBSD 7.3.

    Read the article

  • How do I diagnose the cause of a freeze after resuming in Windows XP (SP3)?

    - by Software Monkey
    I have just built a new computer from parts. Whenever I resume from any sleep mode (S1, S3 or S4) the computer freezes within about 60 seconds of the welcome screen appearing. I have updated the BIOS and all drivers to current from the motherboard manufacturer's site. I have reset BIOS settings to default, including disabling AMD Cool n Quiet. The windows event logs are not helpful at all. Other than immediately after resuming the system is stable as long as AMD CnQ is disabled. The system is: Mobo : MSI 790GX-G65 CPU : AMD Phenom II 965 BE at 3.6 GHz Memory : Corsair DDR3 1600, at 1333 MHz and 9-9-9-21 HDDs : 1 EIDE, 2 SATA in RAID-0 DVD : 1 Card Reader: 1 multi-card reader Keyboard is attached via PS2 and mouse is USB. Any thoughts or pointers would be most welcome. EDIT: It appears that the computer may not freeze if a program is left running which puts it under significant load. I left a stress test running which keeps all cores under 85% load, and my son put the computer to sleep - while this program is running it I have been able to resume from S3 successfully 4 times, compared against about 20 tests with the computer idle which have all frozen. So this may be related to being in an idle state when it resumes.

    Read the article

  • Can't install mysql 5.1 on a windows machine because the last install left artifacts.

    - by Zombies
    After uninstalling mysql 5.1 (64 bit version) I cannot install the win32 version! Apparently the devs felt it neccasery to leave helpful artifacts behind? I have rebooted my machine but no effect.. Running this: C:\Users\User1>net start mysql The MySQL service is starting. The MySQL service could not be started. A system error has occurred. System error 1067 has occurred. The process terminated unexpectedly. And ran this: C:\Program Files (x86)\MySQL\MySQL Server 5.1\bin>mysqld --console 100213 10:52:58 [Note] Plugin 'FEDERATED' is disabled. InnoDB: Error: log file .\ib_logfile0 is of different size 0 10485760 bytes InnoDB: than specified in the .cnf file 0 25165824 bytes! 100213 10:52:59 [ERROR] Plugin 'InnoDB' init function returned error. 100213 10:52:59 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 100213 10:52:59 [ERROR] Unknown/unsupported table type: INNODB 100213 10:52:59 [ERROR] Aborting 100213 10:52:59 [Note] mysqld: Shutdown complete Update: For some reason it looks like it is installing the 32bit DB into the old 64bit directoy.... will look into this... (the bin directory is going into the 32 bit program files directory).

    Read the article

  • Why would e-mail from our own domain not be forwarded to gmail

    - by netboffin
    To solve a problem with spam on our server we tried to forward e-mail from our dedicated server's mailserver(matrix smtp service) to gmail, but while most e-mails got through e-mail from our own domain all went missing. They weren't in the inbox or spam or anywhere else. We've had to go back to using the old system, which means my boss gets a huge amount of spam. We have a windows 2003 server with iis 6 and the matrix smtp service installed. I've toyed with the idea of installing a mail proxy like ASSP but it looks pretty complicated. We're hosting 20 domains on the server as well as our own which has an online shop whose payment system depends on email. I can't start playing around with complicated solutions when it could have disastrous consequences and I don't know enough to implement them safely. So my question has two parts: Part One: Why can't we forward e-mails from people using the same domain. If our domain was foobar.com then [email protected] can't receive from [email protected], but he can receive from everyone else. Part Two: Is there a really simple server side solution to spam that would work with matrix? For instance popfile?

    Read the article

  • Remove directory from URL IIS 7.5

    - by xalx
    I've tried to find a solution to this and found some guides out there but none seem to work. I have the following URL - http://www.mysite.com/aboutus.html However there are some other sites which link to my old hosted site and point to http://www.mysite.com/nw/aboutus.html. My issue here is trying to remove the 'nw' directory from the URL's. I have setup the following URL Rewrite in IIS but it does not seem to do anything, <?xml version="1.0" encoding="UTF-8"?> <configuration> <system.webServer> <rewrite> <rules> <rule name="Redirect all to root folder" enabled="true" stopProcessing="true"> <match url="^nw$|^/nw/(.*)$" /> <conditions> </conditions> <action type="Redirect" url="nw/{R:1}" /> </rule> <rule name="RewriteToFile"> <match url="^(?!nw/)(.*)" /> <conditions> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> </conditions> <action type="Rewrite" url="/{R:1}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Any insight would be appreciated.

    Read the article

  • How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

    - by Maharshi Raval
        I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

    Read the article

  • How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

    - by Maharshi Raval
        I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

    Read the article

  • How to organise storage for media content such as video and music?

    - by thor
    Currently, we have a single server hosting all content: music, video and software. This content is downloaded by users through HTTP. Now free space is coming to an end and we are exploring different ways of extending our storage capacity. We want to do it cheap, simple and reliable (protected from disk/ server faults). Currenly, we see two ways: Add a couple of cheap servers with 4 disks (RAID1 ?), run some distributed file-system on top, like GlusterFS. Pros: hopefully, we will see all our disks as single flat file system, just dump content into it and be done. Cons: could be tricky in configuration and handling of faults. Add a couple of cheap servers, all running HTTP servers. Each piece of content (be it a music file or video) is placed on randomly selected two servers. Pros: don't have to deal with RAID, as content is duplicated; single server failure does not bring down any part of content; doubled distribution capacity (as any signle file could be downloaded from any of two servers hosting it). Cons: requires some scripting on part of distribution of content, adding/ removing servers. Do we miss any other ways? Which of the aforementioned options seems to be the best?

    Read the article

  • Windows 7 Startup fails after installation

    - by Nadav S.
    I have installed Windows 7 Ultimate a week ago. Yesterday I've noticed that the SP1 update is available. After installation of SP1 the computer failed to startup, and had shown a black screen. I couldn't even go to safe mode and F8 didn't help. After some fixing attempts including system restore, startup repair, bootmgr & BCD rebuilding from CMD, I have decided to reinstall Windows (after all, it's only a week old) After the successful installation, I have decided to first install all available updates before I continue. So after the updates download & installation, the computer rebooted. And now I didn't see the black screen again - but in the "Starting Windows..." screen the logo didn't appear and the system didn't startup. Here I could go to safe mode selection window, but it didn't work either ("Loading Windows Files" but nothing). I've also tried: I thought that the CD was corrupted, so I've used a fresh new disk of Windows, tried x86 & x64 versions, the same symptoms, no change. Resetted the BIOS to default, no change. Memory diagnostic HDD diagnostic Restarted Windows WITHOUT INSTALLING UPDATES, but it had the same symptom, so maybe Windows Update is not the case?! I've tried installing it so many times - that I am simply stuck - I can't "reinstall Windows, because it is corrupted...". Maybe the HDD is corrupted? I've also checked it and didn't find a problem.

    Read the article

  • Adding subnet to a vsphere with single vcenter and esxi host

    - by Ilya Rakhlin
    Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

    Read the article

  • "A disk read error occurred" after choosing to boot into Windows XP from GRUB

    - by kellogs
    "A disk read error occurred" appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris Here, sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I cannot recall how exactly have I used testdisk but it once said: Disk /dev/sda - 160 GB / 149 GiB - CHS 19458 255 63 The harddisk (160 GB / 149 GiB) seems too small! (< 169 GB / 157 GiB) Check the harddisk size: HD jumper settings, BIOS detection... So far I have tried to "fixboot" and "chkdsk" from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please? Thank you!

    Read the article

  • web.config file changings guide

    - by Student
    Hi experts how are you all? i am student, and learning asp.net c# visual studio 2010 with using sql server 2005. I have developed a website which has database. I developed this website with self studies taking help from internet. the website is completed and working perfectly in my computer. I have hosting server and domain name registered already. the problem is when I upload my website it doesn't work there the following error displays: Server Error in '/' Application. Configuration Error Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 11: <system.web> Line 12: <customErrors mode="Off" /> Line 13: <compilation debug="false" targetFramework="4.0"/> Line 14: </system.web> Line 15: </configuration> Source File: C:\Inetpub\vhosts\urdureport.com\httpdocs\web.config Line: 13 Version Information: Microsoft .NET Framework Version:2.0.50727.5472; ASP.NET Version:2.0.50727.5474 I don't know what should I do to get it work on hosting server please help me in this regard that what should I do with this. Thank you in advance

    Read the article

  • Extending Expression Blend 4 &amp; Blend for Visual Studio 2012

    - by Chris Skardon
    Just getting this off the bat, I presume this will also work for Blend 5, but I can’t confirm it… Anyhews, I imagine you’re here because you want to know how to create an addin for Blend, so let’s jump right in there! First, and foremost, we’re going to need to ensure our development environment has the right setup, so the checklist: Visual Studio 2012 Blend for Visual Studio 2012 OK, let’s create a new project (class library, .NET 4.5): Hello.Extension The ‘.Extension’ bit is very very important. The addin will not work unless it is named in this way. You can put whatever you want at the front, but it has to have the extension bit. OK, so now we have a solution with one project. To this project we need to add references to the following things: Microsoft.Expression.Extensibility (from c:\program files\Microsoft Visual Studio 11.0\Blend\   -- x86 folder if you are on an x64 windows install) Microsoft.Expression.Framework (same location as above) PresentationCore PresentationFramework WindowsBase System.ComponentModel.Composition Got them? ACE. Let’s now add a project to contain our control, so, create a new WPF Application project, cunningly named something like ‘Hello.Control’… (I’m creating a WPF application here, because I’m too lazy to dig up the correct references, and this will add all the ones I need ) Once that is created, delete the App.xaml and MainWindow.xaml files, we won’t be needing them. You will also need to change the properties of the project itself, so it is only a class library. Once that is done, let’s add a new UserControl, which will be this: <UserControl x:Class="Hello.Control.HelloControl" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" mc:Ignorable="d" d:DesignHeight="300" d:DesignWidth="300"> <Grid> <TextBlock Text="HELLO!!!"/> </Grid> </UserControl> Impressive eh? Now, let’s reference the WPF project from the Extension library. All that’s left now is to code up our extension… So, add a class to the Extension project (name wise doesn’t matter), and make it implement the IPackage interface from the Microsoft.Expression.Extensibility library: public class HelloExtension : IPackage { /**/ } We’ll implement the two methods we need to: public class HelloExtension : IPackage { public void Load(IServices services) { } public void Unload() { } } We’re only really concerned about the Load method in this case, as let’s face it, the extension we have doesn’t need to do a lot to bog off. The interesting thing about the Load method is that it receives an IServices instance. This allows us to get access to all the services that Expression provides, in this case we’re interested in one in particular, the ‘IWindowService’ So, let’s get that bad boy… private IWindowService _windowService; public void Load(IServices services) { _windowService = services.GetService<IWindowService>(); } Nailed it… But why? The WindowService allows us to register our UserControl with Blend, which in turn allows people to activate and see it, which is a big plus point. So, let’s do that… We’ll create an ‘Initialize’ method to create our new control, and add it to the WindowService: private HelloControl _helloControl; public void Initialize() { _helloControl = new HelloControl(); if (_windowService.PaletteRegistry["HelloPanel"] == null) _windowService.RegisterPalette("HelloPanel", _helloControl, "Hello Window"); } First we check that we’re not already registered, and if we’re not we register, the first argument is the identifier used by the service to, well, identify your extension. The second argument is the actual control, the third argument is the name that people will see in the ‘Windows’ menu of Blend itself (so important note here – don’t put anything embarrassing or (need I say it?) sweary…) There are only two things to do now - Call ‘Initialize()’ from our Load method, and Export the class This is easy money – add [Export(typeof(IPackage))] to the top of our class… The full code will (should) look like this: [Export(typeof (IPackage))] public class HelloExtension : IPackage { private HelloControl _helloControl; private IWindowService _windowService; public void Load(IServices services) { _windowService = services.GetService<IWindowService>(); Initialize(); } public void Unload() { } public void Initialize() { _helloControl = new HelloControl(); if (_windowService.PaletteRegistry["HelloControl"] == null) _windowService.RegisterPalette("HelloControl", _helloControl, "Hello Window"); } } If you build this and copy it to your ‘Extensions’ folder in Blend (c:\program files\microsoft visual studio 11.0\blend\) and start Blend, you should see ‘Hello Window’ listed in the Window menu: That as they say is it!

    Read the article

  • How can I setup a Proxy I can sniff traffic from using an ESX vswitch in promiscuous mode?

    - by sandroid
    I have a pretty specific requirement, detailed below. Here's what I'm not looking for help for, to keep things tidy and on topic: How to configure a standard proxy Any ESX setup required to facilitate traffic sniffing How to sniff traffic Any changes in design (my scope limits me) I need to setup a test environment for a network-sniffing based HTTP app monitoring tool, and I need to troubleshoot a client issue but he only has a prod network, so making changes to the config on client's system "just to try" is costly. The goal here is to create a similar system in my lab, and hit the client's webapp and redirect my traffic - using a proxy - into the lab environment. The reason I want to use a proxy is so that only this specific traffic is redirected for all to see, and not all my web traffic (like my visits to serverfault :P). Everything will run inside an ESX 4.1 machine. In there, there is a traffic collection vswitch in promiscuous mode that is not on the local network for security reasons. The VM containing our listening agent is connected to this vswitch. On the same ESX host, I will setup a basic linux server and install a proxy (either apache + mod_proxy or squid, doesn't matter). I'm looking for ideas on how to deploy this for my needs so I can then figure out how to set it up accordingly. Some ideas I've had were to setup two proxies, and have them talk to eachother through this vswitch in promiscuous mode, but it seems like alot of work. Another idea is a dual-homed proxy, but I've never seen/done that before so I'm not sure how doable it is for what I'd like. I am OK with setting up a second vswitch in promiscuous mode to facilitate this if need be, but I cannot put the vswitch on the lan (which is used so my browser would communicate with the proxy) in promiscuous mode. Any ideas are welcome.

    Read the article

  • All of the NTFS hard links damaged, where are hardlinks stored and how to recover them?

    - by String Xu
    This is Windows 7 x64 sp1 on a NTFS file system. All hardlinks within C:\Windows\System32 folder disappear, and the Windows can't boot, because even the osloader, C:\Windows\System32\boot\Winload.exe also disappeared. Nevertheless, the original files are still located in the corresponding C:\Windows\winsxs folders. After booting into the Recovery Environment, and copied one Winload.exe (x64) from other folder, Windows gave an error pointing out that "ntoskrnl.exe is corrupted or missing...its file digital signature cannot be verified" In trying to boot in Safe Mode, the message above was shown after a screen prompting "Loaded \Windows\system32\config\system" Because at this early booting stage, smss.exe was still not loaded, so there is not any dumping and logs. Based on my study, ntoskrnl.exe depends on the following files: C:\windows\system32\PSHED.DLL C:\Windows\System32\hal.dll C:\Windows\System32\kdcom.dll C:\Windows\System32\clfs.sys C:\Windows\System32\ci.dll All those files above are copied from their corresponding folders and verified their md5 with a well-operating Windows 7 x64 SP1. But the booting error is still the same: "ntoskrnl.exe is corrupted or missing..." Background: 1. Before the reboot, there was an windows update going on. Then something unknown happen, almost all processes were broken to run, including the windows task manager, taskmgr.exe. After mount the hard disk to other computer, it seems that all hardlinks within C:\Windows\System32 folder were gone. I tried several data recovery software, but they are not be able to find those disappeared NTFS hard links. So the question is: Where are information about those hard links stored? And how to recover them? Are they depend on some windows service or stored in the registry?

    Read the article

  • How to avoid sshfs freezing?

    - by Andreas Hagen
    So the issue is this: I've installed sshfs on Ubuntu 12.04 and I'm trying to connect to a couple of remote servers. So initially the mount seams successful. Sometimes Gnome even picks it up and displays the "new device found" box at the bottom of the screen. but from here on there is not much that works. Or at least not any more. The first couple of times i connected it seamed to work fine, and I was able to transfer some files, then i disconnected using fusermount -u <folder> and after reconnecting a little later the trouble started. Now after executing sshfs -o ServerAliveInterval=15 -o reconnect -C -o workaround=all -o idmap=user root@<host>:/ <folder>, when I change directory into the mount-point, the shell just freezes. Strangely ls -al <folder> works when listing just the root of the remote system, but nothing more. Also every file-explorer I've tried freezes just like cd <folder>. To me it seamed like there was some kind of zombie thread or something hanging around my system, due to the fact that it did work the first time, so I have tried rebooting but no luck. sshfs -V gives this: SSHFS version 2.3 FUSE library version: 2.8.6 fusermount version: 2.8.6 using FUSE kernel interface version 7.12 So yea, any ideas?

    Read the article

  • Windows VirtualBox failed to attach USB device to Linux Guest

    - by joltmode
    I have Windows 7 64bit Host system, and I am using VirtualBox 4.1.18 (r78361). I have an Arch Linux Guest OS. I have installed VirtualBox Extension Pack (to enable USB2 support) and added my USB device filter to VM. I have also installed the Guest Additions provided by Arch: virtualbox-archlinux-additions (but I have no idea whether it's actually needed for my environment). I can see my USB device from VirtualBox Devices menu. Whenever I am trying to access it, I end up with: Failed to attach the USB device Kingston DT 100 G2 [0100] to the virtual machine Archlinux. USB device 'Kingston DT 100 G2' with UUID {a836ec33-0f41-4ca7-a31d-09cceaf5d173} is busy with a previous request. Please try again later. Details ? Result Code:    E_INVALIDARG (0x80070057) Component:      HostUSBDevice Interface:      IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee:         IConsole {1968b7d3-e3bf-4ceb-99e0-cb7c913317bb} From what I have googled, most guides shows how to solve this the other way around - Linux Host to Windows Guest. How do I resolve this? Update I have tried to Eject (virtually, not physically) the device from my Windows Host system and then try to access the Device from Guest. Same error.

    Read the article

  • Skip new Windows 7 user selection and go to login prompt

    - by Doltknuckle
    We've begun our migration to windows 7 and we ran into an interesting issue. When we hit "CTRL+ALT+DEL" we are brought to the "User selection Screen". Normally, this screen will have an icon for every local user for the machine. These machines are Domain members with "Fast User Switch" disabled so no user names are listed only the "Other User" option. If you click "Other User" or hit enter, the system moves on to the normal login screen where it prompts for user name and password. Here's the issue: We want to find a way to skip over the part where a user selects "Other User". We essentially want the system to always assume that we always want "Other User" and to go directly to the login screen when a user hits "CTRL+ALT+DEL". What I find odd is that the "Other User" doesn't show up until we've had more than one domain user log in. Right after we re-image the machine, the login process goes directly to the user credential prompt. Anyone have any ideas?

    Read the article

  • Unexpected(?) high 'wasted' memory in memcached

    - by Nanne
    Looking at our memcached stats I think I have found an issue I was not aware of before. It seems that we have a strangely high amount of wasted space. I checked with phpmemcacheadmin for a change, and found this image staring at me: Now I was under the impression that the worst-case scenario would be that there is 50% waste, although I am the first to admit not knowing all the details. I have read - amongst others- this page which is indeed somewhat old, but so is our version of memcached. I think I do understand how the system works (e.g.) I believe, but I have a hard time understanding how we could get to 76% wasted space. The eviction rate that phpmemcacheadmin shows is 2 ev/s, so there is some problem here. The primary question is: what can I do to fix this. I could throw more memory at it (there is some extra available I think), maybe I should fiddle with the slab config (is that even possible with this version?), maybe there are other options? Upgrading the memcached version is not a quickly available option. The secondairy question, out of curiosity, is of course if the rate of 75% (and rising) wasted space is expected, and if so, why. System: This is currently not something I can do anything about, I know the memcached version isn't the newest, but these are the cards I've been dealt. Memcached 1.4.5 Apache 2.2.17 PHP 5.3.5

    Read the article

  • Mysql connections hanging in login state

    - by Mark Rose
    Suddenly today, I had an issue with connections to mysql hanging when connecting by IP address (e.g. mysql -h 10.1.248.20), but I could still connection using localhost fine, regardless the user. mysql> show processlist; +----+----------------------+------------------+------+---------+------+-----------------------------------------------------------------------+------------------+ | Id | User | Host | db | Command | Time | State | Info | +----+----------------------+------------------+------+---------+------+-----------------------------------------------------------------------+------------------+ | 1 | system user | | NULL | Connect | 10 | Connecting to master | NULL | | 2 | system user | | NULL | Connect | 10 | Has read all relay log; waiting for the slave I/O thread to update it | NULL | | 37 | unauthenticated user | 10.1.248.3:36694 | NULL | Connect | NULL | login | NULL | | 38 | unauthenticated user | 10.1.248.3:36695 | NULL | Connect | NULL | login | NULL | | 39 | unauthenticated user | 10.1.248.3:36696 | NULL | Connect | NULL | login | NULL | | 40 | root | localhost | NULL | Query | 0 | NULL | show processlist | +----+----------------------+------------------+------+---------+------+-----------------------------------------------------------------------+------------------+ 6 rows in set (0.00 sec) Yes, I realize replication was broken in that output above; that was after I tried restart MySQL (it was an emergency). And as suddenly as things stopped working, they started working again. DNS was working fine at the time. Replication was still working. MySQL was responsive. Does anyone have any idea what would cause MySQL logins from remote IPs to hang suddenly?

    Read the article

< Previous Page | 741 742 743 744 745 746 747 748 749 750 751 752  | Next Page >