Search Results

Search found 29619 results on 1185 pages for 'android virtual device'.

Page 748/1185 | < Previous Page | 744 745 746 747 748 749 750 751 752 753 754 755  | Next Page >

• Network driver for Hyper-V restore from Windows Home Server

  - by Philipp Schmid

  I have backed up Windows Server 2008 running virtualized on Hyper-V to a Windows Home Server 2008 SP1 (I know I should have backed up the VHD instead). Now I need to restore the contents of the VM from WHS. I have created a restore CD ISO and used it to create a new VM. It all works as advertised up to the point where the restore process wants to load the network drivers (it only finds 4 disk drivers on the restore CD. but no network drivers). So I created a virtual floppy and copied the contents of 'Home Server Drivers for Restore onto it. But no luck! I have tried moving the 4 subdirectories into the root of the floppy, but that didn't work either. Finally, I started another instance of the WS 2008 to identify the network driver that the virtualized instance is using (%WINDOWS%\system32\drivers\netvsc60.sys) and copied that file onto the virtual floppy, without success. Does anyone have any suggestions on how to get networking working on a Hyper-V instance running off the Windows Home Server Restore CD? UPDATE: As suggested by delenda, I have added a legacy network adapter to my VM, and indeed I now get a network driver listed! However, the WHS it still not found, even after entering the home server name manually. PHS

  Read the article

• Network Load Balancing, intermittent port problem

  - by Jimmy Chandra

  Trying to troubleshoot an intermittent problem. I think it might be related to an NLB issue. We are using Windows Network Load Balancing to balance load for our multiserver SharePoint front ends. Say... Web Front End 1 IP is 192.168.1.100 and Web Front End 2 IP is 192.168.1.101, the NLB is setup to load balance both WFE servers on any incoming traffic to the IP 192.168.1.200. Sometimes we got an intermittent issue where when we try to access the SharePoint site using 192.168.1.200:8080 (say the site is set up to run on port 8080) from a remote client, it will display page not found. Pinging the 192.168.1.200 will give responses, but when trying to telnet to 192.168.1.200:8080 it just won't connect. However, browsing the SharePoint site directly on individual WFE (192.168.1.100 and 192.168.1.101) show no problem whatsoever. My guess also (we didn't get a chance to try it yet, but I think it should work), if I try connecting remotely to individual server, it will respond just fine. But any attempt on trying to connect using the virtual IP (192.168.1.200) will fail miserably. Funny thing is, after a while it will return back to normal. Anyone had similar experience with this type of problem while implementing NLB before? We are doing this in a virtual environment.

  Read the article

• How to route to a secondary interface on the same physical ethernet?

  - by sjose3612611

  INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

  Read the article

• Change authentication wifi WPA to WEP on Windows 8

  - by Kites

  I use netsh wlan set hostednetwork mode=allow ssid=Kites key=phambaoViet netsh wlan start hostednetwork To share WiFi from LAN network on laptop (Windows 8) to my other device. When I show information netsh wlan show hostednetwork the supported authentication is WPA. My device support authentication WEP only. How can I change the authentication to WEP? Infomation: Interface name: Wi-Fi Driver : Qualcomm Atheros AR9002WB-1NG Wireless Network A dapter Vendor : Qualcomm Atheros Communications Inc. Provider : Microsoft Date : 03/07/2012 Version : 3.0.0.130 INF file : C:\Windows\INF\netathrx.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g 802.11n FIPS 140-2 mode supported : Yes 802.11w Management Frame Protection supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Vendor defined Vendor defined Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP Vendor defined Vendor defined

  Read the article

• VMWare Host Not Responding - VMs are Disconnected (ESXi 3.5)

  - by EyeonTech

  I have inherited a VMWare environement ESX v3i 3.5. I am not fluent with VMWare ESXi so bare with me. Two days ago, when I opened Virtual Centre, one of the Hosts showed up as Not Responding. The error I am seeing is:----- Unable to acquire licenses because license source is unavailable: The license manager has not been started yet, the wrong port@host or license file is being used, or the port or hostname in the license file has been changed. What I have tried: I have Stopped and Started the license server within the application. When I do this, I am able to disconnect the host in Virtual Centre and reconnect. This brings the host back online, but a few minutes later, the host goes to a not responding state again. I have rebooted the server with the Licensing software installed. While browsing Google, I have not been able to find any steps I feel comfortable performing and I would like the opinion of the VMWare pros. Where are the log files I should be looking at to correctly determine what is going on? Has anyone seen this behaviour and how did you resolve it? Thank you

  Read the article

• Ping server NETBIOS name returns wrong IP and "Destination host unreachable"

  - by music2myear

  Problem server is Windows 2008 R2 VM running on VMWare ESXi 4 host. Single network adapter manually assigned single IP address (192.168.1.11). When I ping the server from any other network computer, it returns 192.168.1.124 and "Destination host unreachable". Yesterday I found a second network adapter assigned to this server with an IP of 169.254... indicating it had no real valid IP. Using the MAC addresses I determined which adapter was not needed/not wanted, and removed it using VMWare systems. This is the network Printer Server and, understandably, nothing is printing right now. I've looked at the solutions here Why was my ping answered by a different IP address than the one pinged? and they aren't applicable to my situation for the following reasons: Output of arp -a on another computer returns the correct IP address (.1.11) assigned to the correct MAC address, the incorrect IP .1.124 is not listed, and the MAC of the network adapter I removed yesterday is not listed at all. I checked out the Microsoft KB article which listed pretty much my exact symptoms ( http://support.microsoft.com/kb/981953 ) and it says to check binding orders and look for hidden adapters. But there are no hidden adapters, and there is only one Network Adapter listed in the Binding Order list. Essentially, I can communicate from the server TO any other network device, but I cannot communicate from any other network device TO the server. Help! UPDATE: Solution found, see this solution for the details.

  Read the article

• How do I configured postfix and to use SES, and still be able to forward email from unverified external addresses?

  - by Jeff

  We are using postfix for email group lists (eg "[email protected]" will go to all members) from Amazon EC2 systems. For a variety of reasons (scalability and reliability) we would like to use SES for all outgoing emails. I was able to configure postfix to use SES as the SMTP for outgoing emails. This works fine for all verified emails. But of course, when an outsider emails me at "[email protected]", it chokes. Postfix is configured to forward to my gmail account (via the virtual table), the SES rejects it because the outside user is not verified. So none of our mailing groups configured through postfix will work this way. I would be happy to rewrite all "From" addresses before sending (and simply leave the Reply To as the original sender), but I cannot seem to find a working configuration. No matter what I set in canonical or generic regexps, SES seems to reject all forwarded emails. Surely somebody must have configured postfix with SES to handle virtual addresses? How does this work?

  Read the article

• How can I write automated tests for iptables?

  - by Phil Frost

  I am configuring a Linux router with iptables. I want to write acceptance tests for the configuration that assert things like: traffic from some guy on the internet is not forwarded, and TCP to port 80 on the webserver in the DMZ from hosts on the corporate LAN is forwarded. An ancient FAQ alludes to a iptables -C option which allows one to ask something like, "given a packet from X, to Y, on port Z, would it be accepted or dropped?" Although the FAQ suggests it works like this, for iptables (but maybe not ipchains as it uses in the examples) the -C option seems to not simulate a test packet running through all the rules, but rather checks for the existence for an exactly matching rule. This has little value as a test. I want to assert that the rules have the desired effect, not just that they exist. I've considered creating yet more test VMs and a virtual network, then probing with tools like nmap for effects. However, I'm avoiding this solution due to the complexity of creating all those additional virtual machines, which is really quite a heavy way to generate some test traffic. It would also be nice to have an automated testing methodology which can also work on a real server in production. How else might I solve this problem? Is there some mechanism I might use to generate or simulate arbitrary traffic, then know if it was (or would be) dropped or accepted by iptables?

  Read the article

• ntop to analyse bandwidth usage on multiple ASA 5505

  - by dunxd

  I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

  Read the article

• Two parts: linux startup script to connect to bluetooth and cron to keep it connected

  - by D.R.

  I have a mini bluetooth keyboard and a Raspberry Pi running a Debian-based distro. I know the MAC address of the keyboard but for this question, let's just use AA:BB:CC:DD:EE:FF. Right now I have to have a wired keyboard connected as well as my bluetooth dongle for the mini-keyboard and on the wired keyboard, I have to run the following when the device boots up: sudo hidd --connect AA:BB:CC:DD:EE:FF If the device goes idle for too long, then the bluetooth disconnects and I have to pull out my wired keyboard and retype that same command. What I'm looking for it a way to have that command run at startup and a way to sense if it gets disconnected so that it will auto reconnect. The annoying thing is that they keyboard has to be in pairing mode (even though it has already been paired) when I run that command, otherwise it tells me the host is down. So perhaps the script needs to prevent it from disconnecting due to inactivity, otherwise I'll have to put it back in pairing mode to reconnect. So to recap: - A script to connect at startup (I can make sure to put the keyboard into pairing mode before turning it on) - A script to prevent it from disconnecting (maybe some sort of signal to send to it every 60 seconds or something?) Any help with this is greatly appreciated! StackOverflow is always the best place to find answers to weird questions! I've been searching long and hard for an answer, but finally had to resort to coming here! Thanks!

  Read the article

• Setfacl configuration issue in Linux

  - by Balualways

  I am configuring a Linux Server with ACL[Access Control Lists]. It is not allowing me to perform setfacl operation on one of the directoriy /xfiles. I am able to perform the setfacl on other directories as /tmp /op/applocal/. I am getting the error as : root@asifdl01devv # setfacl -m user:eqtrd:rw-,user:feedmgr:r--,user::---,group::r--,mask:rw-,other:--- /xfiles/change1/testfile setfacl: /xfiles/change1/testfile: Operation not supported I have defined my /etc/fstab as /dev/ROOTVG/rootlv / ext3 defaults 1 1 /dev/ROOTVG/varlv /var ext3 defaults 1 2 /dev/ROOTVG/optlv /opt ext3 defaults 1 2 /dev/ROOTVG/crashlv /var/crash ext3 defaults 1 2 /dev/ROOTVG/tmplv /tmp ext3 defaults 1 2 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/ROOTVG/swaplv swap swap defaults 0 0 /dev/APPVG/home /home ext3 defaults 1 2 /dev/APPVG/archives /archives ext3 defaults 1 2 /dev/APPVG/test /test ext3 defaults 1 2 /dev/APPVG/oracle /opt/oracle ext3 defaults 1 2 /dev/APPVG/ifeeds /xfiles ext3 defaults 1 2 I have a solaris server where the vfstab is defined as cat vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - /dev/vx/dsk/bootdg/swapvol - - swap - no - swap - /tmp tmpfs - yes size=1024m /dev/vx/dsk/bootdg/rootvol /dev/vx/rdsk/bootdg/rootvol / ufs 1 no logging /dev/vx/dsk/bootdg/var /dev/vx/rdsk/bootdg/var /var ufs 1 no logging /dev/vx/dsk/bootdg/home /dev/vx/rdsk/bootdg/home /home ufs 2 yes logging /dev/vx/dsk/APP/test /dev/vx/rdsk/APP/test /test vxfs 3 yes - /dev/vx/dsk/APP/archives /dev/vx/rdsk/APP/archives /archives vxfs 3 yes - /dev/vx/dsk/APP/oracle /dev/vx/rdsk/APP/oracle /opt/oracle vxfs 3 yes - /dev/vx/dsk/APP/xfiles /dev/vx/rdsk/APP/xfiles /xfiles vxfs 3 yes - I am not able to find out the issue. Any help would be appreciated.

  Read the article

• Western Digitial My Book: Can't access the data on the drive

  - by Bryan Denny

  My girlfriend has this external hard drive by Western Digital called a My Book. When the external drive is connected, it does not show it as an accessible disk drive on the computer. However, it shows up fine in Device Manager: I can also see it in Disk Management, but the volume is not mapped to a drive letter, nor can I change the drive letter: It only gives me access to Delete Volume: I would rather not lose the data on the drive if possible. What can I do from here to get to the data? Things I've tried/know: Uninstall drivers and re-install them Device does the same thing when attach to either her Win7 laptop or my Win8 laptop I don't think there's an issue with the HDD itself. No clicking noises, etc. I ran Western Digital Data LifeGuard Diangostics (DLGDIAG) and the SMART Status was a "PASS", all of the SMART Disk Information looked fine. I haven't had the time to run the diag tests yet but I do not believe it's a mechanical issue. The hard drive is inside of an enclosure, I have not attempted to pry the drive out yet. How can I get Windows to properly detect this drive?

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• x display problems in centos 5.5

  - by John Ruiz

  I have a Dell E510 desktop with a geForce 7200 instead of the ATI x600 it came with. I have attempted to install CentOS 5.4 x86_64 (DVD), CentOS 5.5 (net install), and CentOS 5.5 x86_64 (DVD). Gnome desktop. All of these run into the same issue. When I put the DVD into the machine and reboot, the installer begins and I select "graphical install". I see text that say anaconda is starting, and then my screen goes nuts. It's not black, but rather a screen full of diagonal stripes or multiple colors. So I attempted to do a text install of CentOS 5.5 (DVD) and got it installed. When I booted for the first time, I logged into the virtual console and started X (startx). The desktop came up and it already had the display properties GUI up. I changed it from 800x600 to 1680x1050, saw that there were updates available, installed them, and then rebooted. When I start X from the virtual console this time, I get exactly the same display problem as I described before. Does anyone know what might be causing this and what I can do about it? edit: I should also mention that I'm capable of installing Windows 7 and Ubuntu 10.04 onto this machine with absolutely no issues at all.

  Read the article

• How to diagnose website performance/app pool recycling with Windows 2008/IIS7

  - by ilasno

  Ok, so there are various symptoms here (clients and and our own employees complaining of intermittent slowdowns, getting 'kicked out' to login page or just having a save request not properly save the submitted data). The environment: Windows Server 2008 (Datacenter), Service Pack 2, 64-bit, 2x2.8 GHz processors, 7.5 GB RAM MS SQL Server 2008 (running on the same machine) IIS 7 There are ~10 websites running on the server, each in their own application pool - most of these pools are running in Integrated mode, 2 are in Classic, all are on .NET 2.0 and all run as ApplicationPoolIdentity. I'm trying to analyze, diagnose, and troubleshoot and am struggling with where to get more info about what could be happening. Here are some steps i have already taken: Set each application pool to recycle once per day, and removed any other automatic recycling Set a Virtual Memory Limit for each to 1024000KB (1GB) Enabled ALL 'Generate Recycle Event Log Entry' entries (Config Changes, Isapi Reported Unhealthy, Manual Recycle, Private Memory Limit Exceeded, Regular Time Interval, Request Limit Exceeded, Specific Time, Virtual Memory Limit Exceeded) I have seen the app pool processes recycle (in Task Manager) - a new one will start up, and then the first one dies off - and this has happened without the memory or time going over the settings. This is a fairly new server, and most of these came from Windows Server 2003/IIS6. Any 'next steps' for setting up information gathering, logging, diagnosing, etc. would be much appreciated! j

  Read the article

• NTBackup Error: C: is not a valid drive

  - by Chris

  I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• tap interfaces always disabled in linux bridge

  - by Dani Camps

  I have a physical interface eth0, and I want to create two virtual interfaces and bridge them with eth0. For this purpose I do: #Create the virtual interfaces tunctl -t tap0 tunctl -t tap1 ifconfig tap0 up ifconfig tap1 up #Create the bridge brctl addbr br0 brctl stp br0 off brctl addif br0 eth0 brctl addif br0 tap0 brctl addif br0 tap1 #Turning up the bridge ifconfig br0 up However my problem if that the tap interfaces always appear disabled in the bridge, and no traffic flows to them. $brctl show br0 bridge name bridge id STP enabled interfaces br0 8000.080027cabeba no eth2 tap0 tap1 $brctl showstp br0 br0 bridge id 8000.080027cabeba designated root 8000.080027cabeba root port 0 path cost 0 max age 20.00 bridge max age 20.00 hello time 2.00 bridge hello time 2.00 forward delay 15.00 bridge forward delay 15.00 ageing time 300.01 hello timer 0.00 tcn timer 0.00 topology change timer 0.00 gc timer 298.42 flags eth2 (1) port id 8001 state forwarding designated root 8000.080027cabeba path cost 4 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8001 forward delay timer 12.97 designated cost 0 hold timer 1.24 flags tap0 (2) port id 8002 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags tap1 (3) port id 8003 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags Is there any way to set the tap interfaces in forwarding state? I do not understand why they are not because STP is disabled. Cheers Daniel

  Read the article

• Karmic iptables missing kernel moduyles on OpenVZ container

  - by luison

  After an unsuccessful p2v migration of my Ubuntu server to an OpenVZ container which I am stack with I thought I would give a try to a reinstall based on a clean OpenVZ template for Ubuntu 9.10 (from the OpenVZ wiki) When I try to load my iptables rules on the VM machine I've been getting errors which I believe are related to kernel modules not being loaded on the VM from the /vz/XXX.conf template model. I've been testing with a few post I've found but I was stack with the error: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Could not load /lib/modules/2.6.24-10-pve/modules.dep: No such file or directory iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I read about the template not loading all iptables modules so I added modules to the XXX.conf of the VZ virtual machine like this: IPTABLES="ip_tables iptable_filter iptable_mangle ipt_limit ipt_multiport ipt_tos ipt_TOS ipt_REJECT ipt_TCPMSS ipt_tcpmss ipt_ttl ipt_LOG ipt_length ip_conntrack ip_conntrack_ftp ip_conntrack_irc ipt_conntrack ipt_state ipt_helper iptable_nat ip_nat_ftp ip_nat_irc" As the error remained I read that I should build dependencies again on the virtual machine: depmod -a but this returned an error: WARNING: Couldn't open directory /lib/modules/2.6.24-10-pve: No such file or directory FATAL: Could not open /lib/modules/2.6.24-10-pve/modules.dep.temp for writing: No such file or directory So I read again about creating the directory empty and redoing "depmod -a" it. I now don't get the dependancies error but get this and I don't have a clue how to proceed: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Module ip_tables not found. iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I understand that iptables rules have to be different on the VM machine and perhaps some of the rules we are trying to apply (from our physical server) are not compatible but these are just source IP and destination port checks that I would like to be able to have available . I've heard that on the CentOS template there are no issues with this, so I understand is to do with VM config. Any help would be greatly appreciated.

  Read the article

• How do I boot [embedded] linux from sd card?

  - by Brandon Yates

  I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

  Read the article

• Reducing video mode switching during Linux boot

  - by Zack

  When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

  Read the article

• Constant beeping

  - by Bogi Juul Peterson

  My computer has a problem with beeping. I'll first tell you how it started: One night I decided to watch a cartoon, and I took some water and food with me to eat while I watch. I fell asleep and when I woke up I had spilled water all over my keyboard. I didn't react quickly, because it went unnoticed for about 1 and a half hours. When I noticed, I quickly put my laptop on a radiator to try to dry it. When I turned the computer on there was a constant beeping sound. I didn't know what caused it, and I'm still not sure, but I think it has something to do with the USB hub. If I let the computer stand for some hours without any USB connections, it's fine, but when I put any kind of USB device in, it starts beeping. The laptop keyboard doesn't work so I have to have some kind of USB device connected to use the computer. The beeping is going on while I'm writing this and it makes my computer lag so much that it can make delays from the keyboard be from 1 second to 10 seconds. I need this computer because I don't have the money to buy a new one, and I have to use this computer for homework and games. The beeping is constant, with less than a second between beeps. If anyone has a solution, please help.

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• 100% iowait + drive faults in dmesg

  - by w00t

  Hi, I have a server on which resides a fairly visited web app. It has a raid1 of 2 HDDs, 64MB Buffer, 7200 RPM. Today it started throwing out errors like: kernel: ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen kernel: ata2.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in kernel: res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) kernel: ata2.00: status: { DRDY } kernel: ata2: hard resetting link kernel: ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: max_sectors limited to 256 for NCQ kernel: ata2.00: configured for UDMA/133 kernel: sd 1:0:0:0: timing out command, waited 7s kernel: ata2: EH complete kernel: SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) kernel: sda: Write Protect is off kernel: SCSI device sda: drive cache: write back All day long it has been in load higher than 10-15. I am monitoring it with atop and it gives some bizarre readings: DSK | sda | busy 100% | read 2 | write 208 | KiB/r 16 | KiB/w 32 | MBr/s 0.00 | MBw/s 0.65 | avq 86.17 | avio 47.6 ms | DSK | sdb | busy 1% | read 10 | write 117 | KiB/r 17 | KiB/w 5 | MBr/s 0.02 | MBw/s 0.07 | avq 4.86 | avio 1.04 ms | I frankly don't understand why only sda is taking all the hit. I do have one process that is constantly writing with 1-2megs but what the hell.. 100% iowait?

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

< Previous Page | 744 745 746 747 748 749 750 751 752 753 754 755  | Next Page >