Search Results

Search found 39156 results on 1567 pages for 'device driver development'.

Page 748/1567 | < Previous Page | 744 745 746 747 748 749 750 751 752 753 754 755  | Next Page >

  • windows xp blue screen dumping physical memory

    - by dotnet-practitioner
    I get following blue screen after running my laptop for an hour... A problem has been detected and windows has been shut down to prevent damange to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as cashing or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and the select safe mode. Technical Information: * STOP 0x0000008E (0xc0000005, 0x805B03F5, 0xF703DC7C, 0x00000000) Beginning dump of physical memory Physical memory dump complete. Contact you system administrator or technical support group for further assistance. so.... if this is a faulty memory.... from where I could buy RAM for following laptop.... TOSHIBA SATELLITE A45-S250 My local Frys store does not carry memory for this laptop.

    Read the article

  • FastGate A20 Line And Himem.sys Issue With Updating BIOS

    - by Boris_yo
    I have been persistent with a thought to perform my first BIOS update ever through MS-DOS but have been postponing this task until today. Despite people telling me any bootable ISO will do it either through CD-ROM or RAMDRIVE, I am still having problems. First is the problem with CD-ROM driver trying to make it work with 4 driver files (cd1.SYS, cd2.SYS, cd3.SYS, cd4.SYS) as well as starting RAMDISK proved to be failure: CD-ROM XMS Allocation Error RAMDISK XMS Allocaton Error (X: and R: drives not working) This A20 line seemed to be the obstacle which then after a couple of searches pointed me to this article on Microsoft website. It seems that FastGate is the culprit which takes over A20 line and conflicts with himem.sys which should be handling it causing the driver to be unable to allocate memory resources. Albeit article suggests 2 workarounds which is disabling FastGate option or adding switch, I read that the former workaround could cause problems which involves later tinkering BIOS, disabling shadow copy etc. while the latter workaround can just hang system as stated in the link above. I assume it just hangs the boot process from image file though. Summing up the above, I am cautious and think it is risky to follow both workarounds because disabling FastGate or trying adding switch by trying available switches from 1-14 or 16, could crash the BIOS update process by itself. I could do this without the need for himem.sys with bootable USB thumbdrive by making it to be seen as USB-HDD, but some time ago I read that it is never a good idea to update BIOS from hard drive so even thought it is simulation, who knows... Maybe it will deactivate hard drive in the middle of the BIOS update process or even USB thumbdrive per se? One forum discussion was about updating BIOS and somebody suggested to not load himem.sys for some reason, but now that I think of it, what if BIOS update needs upper memory?

    Read the article

  • Can't Install Win2k8 On KVM - Classic 0x80070013 error

    - by javano
    I am trying to install Win2k8 Std as a KVM guest on Debian Squeeze. As you can see from these screen shots; No drives are detected (I have blanked out a 20GB image for testing) - screenshot1 I am using this driver CD: - screenshot2 I have signed the Win7 driver (I assume this was the most appropriate one?) - screenshot3 I can now see an unpartitioned drive - screenshot4 But I can't create a new partition on here, getting the error code 0x80070013 - screenshot5 I have had this error code before but only on a physical server. If I remember correctly it was complaining because the disks were partitioned as GPT (because it was a server that was being re-purposed) so repartitioning with an MS-DOS table fixed that. This is a blank disk image though. What is wrong here, and how can I correct this? Thank you. UPDATE I have booted the VM with a Gparted-Live disk and formatted this volume with an MS-DOS partitioning scheme, and a single 20GB NTFS file system. Now when I boot the Win2k8 CD, load my drivers, I get a different error. As you can see at the bottom of screenshot6 "Windows cannot be installed on this hard drive space. Windows must be installed to a partition formatted as NTFS". Clicking format produces the error (0x80004005) on the screen, so I think this is still a driver issue because Windows can see the drive but not interact with it properly. Is that insane thinking?

    Read the article

  • Enabling JMX for proxool with tomcat

    - by dialt0ne
    I am trying to get proxool's MBeans available so that I can see/manipulate them with jconsole. I have jconsole working, but I don't see anything related to proxool. The system is using Sun Java 1.5.0_17 (I know, I know... I'm working with the developers to upgrade). JMX is enabled by modifying $JAVA_OPTS in my tomcat 5.5 startup script: SJO="$SJO -Dcom.sun.management.jmxremote" SJO="$SJO -Dcom.sun.management.jmxremote.port=4998" SJO="$SJO -Dcom.sun.management.jmxremote.authenticate=false" SJO="$SJO -Dcom.sun.management.jmxremote.ssl=false" JAVA_OPTS="$JAVA_OPTS $SJO" I have proxool configured with JNDI in server.xml: <GlobalNamingResources> <Resource name="jdbc/database" auth="Container" type="javax.sql.DataSource" factory="org.logicalcobwebs.proxool.ProxoolDataSource" user="username" password="password" proxool.driver-url="jdbc:oracle:thin:@fqdn.example.com:1521:MYSID" proxool.driver-class="oracle.jdbc.driver.OracleDriver" proxool.alias="mysid" proxool.maximum-connection-count="20" proxool.statistics="20s,5m,15m" proxool.statistics-log-level="INFO" proxool.jmx="true" proxool.verbose="true" /> </GlobalNamingResources> My test .jsp can run queries and I can see it using the connections with the proxool admin servlet, but I'm unsure if there's more I need to configure in tomcat or proxool to get JMX functioning. Advice? jmxproxy info edit: The jmxproxy servlet is working - when I go to the URL http://tomcatserver.example.com:4999/manager/jmxproxy/?qry=*:type%3DRequestProcessor,* the results are: OK - Number of results: 2 Name: Catalina:type=RequestProcessor,worker=http-8080,name=HttpRequest0 modelerType: org.apache.coyote.RequestInfo bytesSent: 0 requestBytesSent: 0 contentLength: -1 bytesReceived: 0 requestProcessingTime: 1297983483666 globalProcessor: org.apache.coyote.RequestGroupInfo@32dc51c8 requestBytesReceived: 0 serverPort: -1 stage: 0 requestCount: 0 maxTime: 0 processingTime: 0 errorCount: 0 Name: Catalina:type=RequestProcessor,worker=jk-127.0.0.1-8009,name=JkRequest794 modelerType: org.apache.coyote.RequestInfo virtualHost: tomcatserver.example.com bytesSent: 0 method: GET remoteAddr: 172.30.3.51 requestBytesSent: 0 contentLength: -1 workerThreadName: TP-Processor15 bytesReceived: 0 requestProcessingTime: 9 globalProcessor: org.apache.coyote.RequestGroupInfo@1e7d3b8e protocol: HTTP/1.1 currentQueryString: qry=*%3Atype%3DRequestProcessor%2C* requestBytesReceived: 0 serverPort: 4999 stage: 3 requestCount: 0 maxTime: 0 processingTime: 0 currentUri: /manager/jmxproxy/ errorCount: 0 And more to the point http://tomcatserver.example.com:4999/manager/jmxproxy/?qry=Catalina:type%3DEnvironment,resourcetype%3DGlobal,name%3DProxool yields: OK - Number of results: 0

    Read the article

  • Drivers and firmware for the LiteOn ihap-122-9 DVD drive

    - by Sandy
    I'm trying to replace the DVD drive in my old PC. LiteOn.com is a mess and I can't find a single working driver or firmware update there, or anywhere. Windows XP tries to use a default, generic driver dated 2001. (About 9 years before this drive even existed.) http://www.firmwarehq.com/download_1..._6L0H.EXE.html This correctly finds my LiteOn ihap-122-9 DVD Drive. It correctly finds that I'm currently using firmware 6L0F. It correctly tries to install 6L0H. It completes 100% but then just fails and says "contact your vendor". Does anyone know why? Where can I actually get drivers... and firmware updates... that actually work for the ihap-122-9? Apparently, the newest driver IS the 1 made 9 years before the drive existed. (Unbelievable.) And the latest firmware is the 1 that is already in the drive. (Common.) No other drive I've had in this computer ever had a problem. This brand new LiteOn is doing this: Opening MY COMPUTER now takes 60 seconds. MY COMPUTER marking the drive as "DVD F:" takes another 30 seconds. MY COMPUTER showing "Batman II" title takes another 15 seconds. Clicking and running the movie will take another 30 seconds for the main-menu to appear. The movie starts about 20 seconds later. The movie runs fine for 1-2 seconds... then stops for 5 seconds.... then starts again and plays for 1-2 seconds. Repeats for 2 hours. (It happens with all store-bought DVDs and all home-made DVDs.)

    Read the article

  • Exim4 Smart Host Relay

    - by ColinM
    I am running Exim 4.71. I want to: Route all email from A.com through mail.A.com Route all email from [B-E].com through mail.B.com Send all other email directly. Here is the configuration I have that doesn't work like I hoped: domainlist a_domains = a.com domainlist b_domains = b.com : c.com : d.com : e.com begin routers smart_route_a: driver = manualroute domains = +a_domains transport = remote_smtp route_list = +a_domains mail.a.com no_more smart_route_b: driver = manualroute domains = +b_domains transport = remote_smtp route_list = +b_domains mail.mollenhour.com no_more dnslookup: driver = dnslookup domains = ! +local_domains transport = remote_smtp ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 no_more When I send an email e.g. with PHP's mail() or Zend_Mail_Transport_Smtp setting both From: and Return-Path: as [email protected], the smart_route_a router is not used, the dnslookup is used instead. Disabling dnslookup results in no mail being sent. From the logs it appears that email sent to [email protected] uses smart_route_a, but the same email sent from [email protected] to [email protected] is sent using dnslookup. How do I make email from [email protected] be relayed via mail.a.com?

    Read the article

  • Toshiba Satellite P755D USB 3.0 Drivers Missing - Windows 7 Professional

    - by nicorellius
    I bought a Toshiba Satellite P755D recently and installed Windows 7 Professional on the machine. It runs great. But I noticed the exclamation point in the yellow triangle icon in the Device Manager next to the Universal Serial Buss (USB) Controller (I'm assuming this is the USB 3.0 controller because mine doesn't recognize devices). Normally, when this kind of thing happens I go to the manufacturer's website and download appropriate drivers and call it a day. But not this time... I browsed to my model and found no driver for the USB 3.0 controller. I tried other HW and Utility drivers, thinking they would be bundled. No luck. I tried looking up the motherboard in my machine. Generic name, no luck. I then called Toshiba technical support and they tried basic troubleshooting, eg, uninstall device, reboot, for auto-installation; no luck. I popped the Windows 7 disk back in and tried to get information that way, no luck. Finally, the technical support guy said he would look into the engineer's system to see if there was a specific driver available and that's where I'm at. The technician told me that these USB 3.0 drivers come within the native driver pack in windows but that doesn't seem to be the case. Any ideas? EDIT - See attached screen shots.

    Read the article

  • Seemingly random network connectivity.

    - by AngryHacker
    This has been driving me nuts for a while. When I turn on the PC (which has a wired Ethernet connection), it cannot be accessed by other computers on the network. In other words, inbound connections do not work. The firewall is disabled. The PC itself can hit up anything it wants just fine. By process of elimination, I've figured out that checking or unchecking the Eaclift driver in the properties for my network connection restored the inbound connection. I do not know what Eaclift driver is or does or how it even got on my PC (e.g. I am not allowed to uninstall it either). And it does not matter whether it's on or off - I just need to toggle it to restore connectivity. One other thing that happens when I toggle the Eaclift driver, is than an Internet Connection icon appears in the Network Connections and it was not there before. Can someone shed some light as to what is going on? How to fix it so that I don't have to deal with this insanity?

    Read the article

  • GUI interfaces to ATI card behave weirdly out of the box and after updates.

    - by jdk
    My Lenovo W500 came with an ATI Mobility FireGL V5700 and both the Catalyst control center software and Vista display manager display four monitors. What's really annoying is the behaviour. My two active displays (laptop display + my external monitor) are always #s 3 and 4 respectively which doesn't make sense. This is out of the box. Additionally dragging & dropping is jumpy and displays #1 and 2 (always inactive because they don't exist to the software) are often preventing me from dragging #3 and 4 to the rightmost side. They also auto-snap to weird positions and certain sensible positions like position one directly over top of the other are not possible. The exact same annoyances are present when using the Windows Display manager too. In other words the interface is crap and I'm looking for a fix that's not wishing I had gone with nVidia instead. I've updated drivers, and Catalyst control centre. Have latest Windows and AMD/ATI updates. Any thoughts? Graphics Software Driver Packaging Version 8.563.2.1-090401a-079160C-Lenovo Provider ATI Technologies Inc. 2D Driver Version 7.01.01.849 2D Driver File Path /REGISTRY/MACHINE/SYSTEM/ControlSet001/Control/Class/{4D36E968-E325-11CE-BFC1-08002BE10318}/0001 Direct3D Version 7.14.10.0630 OpenGL Version 6.14.10.8306 Catalyst® Control Center Version 2009.0401.1328.22301 Graphics Hardware Primary Adapter Graphics Card Manufacturer Powered by ATI Graphics Chipset ATI Mobility FireGL V5700 Device ID 9591 Vendor 1002 Subsystem ID 2126 Subsystem Vendor ID 17AA Graphics Bus Capability PCI Express 2.0 Maximum Bus Setting PCI Express 2.0 x16 BIOS Version 010.088.000.021 BIOS Part Number BK-ATI VER010.088.000.021.034663 BIOS Date 2009/09/30 Memory Size 512 MB Memory Type DDR3 Core Clock in MHz 600 MHz Memory Clock in MHz 700 MHz

    Read the article

  • Printing special / extended characters on web page - Firefox or printer issue?

    - by edmicman
    My dad brought this to my attention and I'm looking into it, but thought I'd post here and see if anyone has any ideas... He's running Win7, using Firefox and printing to a wireless connected Brother HL-2170W printer. He's got a web page (http://cornandsoybeandigest.com/inputs/fertilizer/applying-nitrogen-after-planting-0512/index.html) that has extended/special characters in it - the funny "a" in Fernandez. The characters show correctly in Firefox on the page. He printed it, and the extended "a" printed as a diamond with a question mark. He says it shows that way in the print preview, too. I pulled up the same page in Ubuntu, Firefox, and it displayed in my print preview and physically printed everything correctly. I just checked on my wife's Win7 PC in Firefox and the print preview looked correct on her system, too. We have a Brother 2040 here. Soooo, my question is, is this possibly a problem in the browser somehow, or the printer driver? I'm leaning towards the printer driver now, but I can't say I've run into this before. Is it a setting somewhere? I just installed this printer for him the other day, using the CD that came with it; I could try updating the driver from Brother's website I guess. Is there anything else I should look at or check? Thanks!

    Read the article

  • Monitor flickers in native resolution.

    - by ptikobj
    With my new Samsung Syncmaster BX2450 I have the following problem: In Windows XP (SP2), all resolutions above 1440x900 have either strange pixel errors or an extreme flickering. It seems, that the effect worsens for higher resolutions. In special, I would like to run the monitor with its native resolution (1920x1080), however I can't watch longer than 5 seconds on the monitor because of the flickering... My Graphics Card is a Geforce FX 5200 with the most up-to-date driver (according to Nvidia.com: Forceware 175.19) and I'm having the monitor connected to its DVI-output. The strange thing is, under Ubuntu 10.04, all resolutions work just perfect, so the display must be alright. edit: seems to be a driver problem... if I use the proprietary NVIDIA drivers in Ubuntu, I have the same problem as in Windows. I would like to reformulate my question: Is there a modified/alternative Geforce FX 5200 driver (as there is in Ubuntu) for Windows that allows me to use 1920x1020 without problems ? I already tried the omega drivers: unfortunately, it still looks poor on the native resolution.

    Read the article

  • How can I start hostednetwork on Windows 7?

    - by Pirozek
    When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

    Read the article

  • Get Matrox Millenium video card working in Ubuntu 9.10

    - by wcoenen
    I have installed Ubuntu 9.10 on an old PC and it is mostly working, except for some heavy drawing defects that show up whenever I start dragging a window or scrolling inside a window or menu. It looks like the video driver copies the rectangle being moved to the wrong location. I have taken a look in /var/log/Xorg.0.log and the following line shows the detected video card: (--) PCI:*(0:0:8:0) 102b:0519:0000:0000 Matrox Graphics, Inc. MGA 2064W [Millennium] rev 1, Mem@ 0xf9800000/16384, 0xfb000000/8388608, BIOS @0x????????/65536 (==) Using default built-in configuration (30 lines) (==) --- Start of built-in configuration --- Section "Device" Identifier "Builtin Default mga Device 0" Driver "mga" EndSection How do I fix the drawing defects? It turned out that the 24 bit color depth (automatically selected by ubuntu 9.10) was the problem; apparantly the mga driver doesn't handle this well for cards with little memory. I took the following steps to resolve the issue (you can skip the first three steps if you already have a semi-working xorg.conf file): Reboot ubuntu in recovery mode, to get a root console without X running. Run Xorg -configure to generate a xorg.conf.new file Copy the file to /etc/X11/xorg.conf with cp xorg.conf.new /etc/X11/xorg.conf (assuming it didn't exist yet; that's why I generated it) Open the new config file with sudo nano /etc/X11/xorg.conf and make sure the screen section is configured for 16 bit color depth like this: Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 16 SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection EndSection I can't guarantee those were the only important changes I made - I tried a few things in my attempts to create a valid xorg.conf file. But I'm pretty sure that the screen section was the important part.

    Read the article

  • Microsoft Deployment Toolkit 2012 Error

    - by Jacob Schaer
    I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

    Read the article

  • How do I connect remotely to SQL Server from Windows client?

    - by humble_coder
    Hi All, Having a bit of an issue connecting to SQL SERVER remotely from Windows. I've verified that all of my settings are correct via SQL SERVER MANAGEMENT STUDIO EXPRESS and SQL SERVER CONFIGURATION MANAGER. I can connect remotely using ODBC drivers from other OSes (e.g. OS X, Linux, etc). However, when I connect with the same credentials from a remote Windows machine using "SQL SERVER" as the driver I am told that the system cannot connect. I've tried creating an ODBC Data Source and I get the same error: Connection failed: SQLState: '01000' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]ConnectionOpen(InvalidInstance()). Connection failed: SQLState: '08001' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]Invalid Connection From the non-windows machines I can use the IP address of the SQL Server just fine. However, on the remote Windows machine, neither IP address nor named instance works. FYI, I can create an ODBC Data Source using the named instance on the machine actually running the SQL Server (but this is, of course, nothing special -- just proof that it isn't completely hosed). One interesting note: If I use SQL STUDIO 2005 from a Windows client machine, I can use the IP address to connect remotely. Still, the whole reason I bring this up is because I need to use a software package I've written to connect to SQL Server remotely from Windows machines as well. Previously the solution was only needed to xfer data from SQL Server into a PostGRES or MySQL database on non-Windows machines (due to DBA preference). However, now they also want to move the data from the legacy software to MySQL even on Windows. Any assistance would be most appreciated. Feel free to provide a full example connection string. Best

    Read the article

  • Windows Server 2003 (w/Exchange) move to new machine

    - by James Booker
    I have an ageing domain controller (the only one on a 10-pc network) which needs rebooting often. I have a Dell Poweredge 2850 server doing nothing, so I'd like to move the DC to that, but here's the catch - I don't have Win2k Server Std install media any more as it's been lost. I purchased "Easus Todo Backup Advanced Server" which claims to be able to recover to dissimilar metal, but it's not quite working (although I don't think it's the product's fault) I know the server and PERC RAID card are good because I installed Ubuntu on the logical drive (4 x 72GB disks RAID 5) no problems. I've booted frmo the Easus Todo backup CD (which is WinPE based) and recovered to the logical disk on the RAID (after installing driver inside the WinPE environment from a NAS drive) The problem is when I boot the server, I can get the OS selection menu, but any option results in a blank screen, with no errors. I figure this is probably because the driver wasn't installed on the old machine (which is IDE-based (i know, i know!) and doesn;t have a RAID controller) I've booted from the CD and copied the mraid35x.sys file to the c:\windows\system32\drivers folder on the recovered system, but it makes no difference. I made a boot.ini with rdisks 0-10 defined, and booting from each of these resulted in a file error (i.e. 'this isn't a real disk') - the only disk that gets any response (the blank screen) is multi(0)disk(0)rdisk(0)partition(1) which just gives me the blank black screen and no disk activity. Is there any way I can force the drvier to be installed on the source system (so i can do a full backup again), i've tried right-clicking the oemsetup.inf and clicking install, but it didn't actually do anything. I attempted to force it with the 'Add new hardware' wizard and forcing with the 'have disk' option but it still gave me no hardware to select. Also I've got an identical machine running WinXP which uses the PERC driver successfully (which was obviously done at install time) and the boot.ini settings are the same : multi(0)disk(0)rdisk(0)partition(1) Any ideas would be appreciated.

    Read the article

  • Windows 7, Black screen with cursor, impossible to logon

    - by PJC
    First - I have gone through as many possible solutions I've found here and elsewhere. [Edit - to describe the issue in more detail, the PC appears to boot correctly, but instead of the logon screen, I have been getting a black screen WITH the pointer cursor, and it responds correctly to the mouse. Pressing CTL-ALT-DEL brings up the logon screen's background, but with no logon area nor any other content. This screen was at the full resolution before I uninstalled the graphics driver in safe-mode.] I also just ran a full up-to-date AVG scan from boot media. [Edit - the AVG scan, which was updated to today's virus signatures, found no issues at all.] So - steps I've tried: Safe Boot, Restore from before the issue - done, no help. Uninstall the graphics driver - done, now i have a 1024x768 fallback screen, still no way in. sfc /scannow - only doable from Safe boot obviously, but no change. [Edit - booting from restore media, performing a startup repair and...]Restore further back - restored to 2 days ago, and I'd had many reboots since then with no problem. Enable autologin to try to get beyond the login screen - done, doesn't work. It seems the best advice is complete reinstall, but I really don't want to do that because it'll take 3-4 days to add all the apps I use. Some key points to note - in both states - before and after removing the video driver, I always had a mouse cursor on the screen. CTL-ALT-DEL flashes up the login background, but no login info. I can (and often do) reinstall from scratch, but was at a fairly stable state before this, and would prefer not to. -Paul

    Read the article

  • How can I make AdobePS recognize my printer in Win98se?

    - by Jeff
    I am trying to use the adobe product: "PostScript Printer Driver AdobePS 4.2.6 for Windows 95 and Windows 98" to connect a new HP laser printer (CP1025nw) via USB to a machine running win98SE. I am using the PPD file for "HP color LaserJet PS". The Adobe utility installs the printer, and it shows up on the printer list ... but it doesn't print. I get an error message (sometimes) that an error occurred writing to USB001.. Evidently, AdobePS cannot "See" the printer. I suspect there is a problem wrt the printer port. Nothing I pick works. I have two virtual printer ports, USB001 and USB002 which were created during the installation of an HP inkjet printer. The inkjet will work on either of these, but the laser printer works on neither. When I connect the laserjet printer, the windows New Hardware Wizard activates, but I don't see how to point it at the AdobePS Postscript driver. HP has no support whatsoever for win98, so there's no hope of getting help from them. The printer works great with the several winXP computers connected through either the network connection or the USB. So, how do I convince Win98se to use the adobe postscript printer driver? Is this printer even a postscript printer? Is there a better way to get win98se to talk to this printer? Any suggestions?

    Read the article

  • Wi-Fi won't automatically connect (box in Windows configuration gets unchecked)

    - by greg88
    The checkbox that says "Use windows to configure my wireless network settings" keeps getting unchecked (Wirless Network Connection - Change advanced settings - Wireless networks tab.) How do I stop that from happening? (So the wi-fi will reconnect.) When I manually re-check the box, it automatically connects.) I have a D-Link AirPremier DWL-G550 PCI adapter. I installed the newest driver, 5.3.0.46, and that didn't solve the problem. I took the "Atheros Client Utility" (the program window says "D-Link AirPremier Client Utility" when you run it) out of the start menu, rebooted, and that didn't solve the problem. (That utility puts a signal bar similiar to the one MS Windows puts there, and it's gone now.) The D-Link client utility has an option to automatically connect to preferred networks, but it is greyed out. It is also greyed out if I install the driver and utility right off the D-Link installation CD, so the problem isn't that the utility and driver are incompatible versions. I want to use Windows to handle the connection anyway, as the D-Link utility is garbage. Windows XP SP3 w/all current updates.

    Read the article

  • How does one get UI_USER_INTERFACE_IDIOM() to work with iPhone OS SDK < 3.2

    - by drootang
    Apple advises using the following code to detect whether running on an iPad or iPhone/iPod Touch: if (UI_USER_INTERFACE_IDIOM() == UIUserInterfaceIdiomPad) { // The device is an iPad running iPhone 3.2 or later. // [for example, load appropriate iPad nib file] } else { // The device is an iPhone or iPod touch. // [for example, load appropriate iPhone nib file] } The problem is that UI_USER_INTERFACE_IDIOM() and UIUserInterfaceIdiomPad are NOT defined in the SDKs priory to 3.2. This seems to completely defeat the purpose of such a function. They can only be compiled and run on iPhone OS 3.2 (iPhone OS 3.2 can only be run on iPad). So if you can use UI_USER_INTERFACE_IDIOM(), the result will always be to indicate an iPad. If you include this code and target OS 3.1.3 (the most recent iPhone/iPod Touch OS) in order to test your iPhone-bound universal app code, you will get compiler errors since the symbols are not defined in 3.1.3 or earlier. If this is the recommended-by-Apple approach to runtime device-detection, what am I doing wrong? Has anyone succeeded using this approach to device-detection?

    Read the article

  • UI_USER_INTERFACE_IDIOM() does not work with iPhone OS SDK < 3.2

    - by drootang
    Apple advises using the following code to detect whether running on an iPad or iPhone/iPod Touch: if (UI_USER_INTERFACE_IDIOM() == UIUserInterfaceIdiomPad) { // The device is an iPad running iPhone 3.2 or later. // [for example, load appropriate iPad nib file] } else { // The device is an iPhone or iPod touch. // [for example, load appropriate iPhone nib file] } The problem is that UI_USER_INTERFACE_IDIOM() and UIUserInterfaceIdiomPad are NOT defined in the SDKs priory to 3.2. This seems to completely defeat the purpose of such a function. They can only be compiled and run on iPhone OS 3.2 (iPhone OS 3.2 can only be run on iPad). So if you can use UI_USER_INTERFACE_IDIOM(), the result will always be to indicate an iPad. If you include this code and target OS 3.1.3 (the most recent iPhone/iPod Touch OS) in order to test your iPhone-bound universal app code, you will get compiler errors since the symbols are not defined in 3.1.3 or earlier. If this is the recommended-by-Apple approach to runtime device-detection, what am I doing wrong? Has anyone succeeded using this approach to device-detection?

    Read the article

  • shouldAutorotateToInterfaceOrientation called several times in a row without any rotation

    - by Mike
    I am trying to implement some interface changes in my app, based on the device rotation. My app is a view based app. So, its main view controller has a didload method. The app starts in portrait. Almost all changes on the device orientation triggers the shouldAutorotateToInterfaceOrientation method but this method is not called when the device is put on portrait, after coming from any landscape orientation. While debugging the app, I have put a NSLog(@"orientation=%d", interfaceOrientation); on my shouldAutorotateToInterfaceOrientation method, and what I see is quite strange: When I run the app, shouldAutorotateToInterfaceOrientation is called 6 times before the app's interface even appears. Every time it runs, it reports a different number for the orientation: the order it reports on console is: portrait, portrait, portrait, landscape right, landscape left, upside down) (????). During this time the app is just beginning. All 6 times the debugger reports the method being run by the app's delegate. So, here comes the questions: WHy shouldAutorotateToInterfaceOrientation is not being called when the device enters on portrait? Why is this method running 6 times called by the delegate even before the app starts and shows its interface if no rotation is being done? thanks.

    Read the article

  • UiModeManager - NightMode (FroYo)

    - by Kaloer
    Hi there, I have been trying to turn off the buttons' light in my application using the UiModeManager's nightmode function. The default Desk Clock application (Nexus One) turns off the buttons' light when it is dimmed, and I want to do this as well. I've tried using the following code: UiModeManager mgr = (UiModeManager) getSystemService(UI_MODE_SERVICE); mgr.setNightMode(UiModeManager.MODE_NIGHT_YES); The UiModeManager.setNightMode(int mode) documentation says this: Sets the night mode. Changes to the night mode are only effective when the car or desk mode is enabled on a device. Does that mean that the device has to be physically in a desk dock? I can set the device to car mode using the UiModeManager.enableCarMode(int flags) method. This works fine, but it doesn't turn off the lights, it only dims the screen's backlight. Is there a way to set the device into desk mode without using a physical desk dock? As the FroYo source code is not yet released, I cannot look at the build-in Desk Clock application. Thanks in advantage.

    Read the article

  • Opened SerialPort crashes C# application

    - by Stefan Teitge
    The computer is connected to measuring device via a physical COM1. I have simple form where I open a serial port, tell the device that I'm alive and occasionally the device sends data. (every some minutes) Thread _readThread = new Thread(Read); SerialPort _serialPort = new SerialPort("COM1", 9600); _serialPort.Parity = Parity.None; _serialPort.DataBits = 8; _serialPort.StopBits = StopBits.One; _serialPort.Handshake = Handshake.None; _serialPort.DtrEnable = true; _serialPort.Open(); _readThread.Start(); _serialPort.Write("#listening"); The read function (which works): public void Read() { string message = _serialPort.ReadLine(); } After approximately one minute the application crashes (even while debugging). It reports an ObjectDisposedException (for the underlying stream?). The message tells that the SafeHandle was closed. Stack strace is below: at Microsoft.Win32.UnsafeNativeMethods.GetOverlappedResult(SafeFileHandle hFile, NativeOverlapped lpOverlapped, Int32& lpNumberOfBytesTransferred, Boolean bWait) at System.IO.Ports.SerialStream.EventLoopRunner.WaitForCommEvent() at System.Threading.ThreadHelper.ThreadStart_Context(Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ThreadHelper.ThreadStart()* Any ideas? The problem is reported widely but usually involve the device beeing physically detached from the PC.

    Read the article

  • Symbolicate adhoc iphone app crashes.

    - by gotye
    Hey everyone, I can't manage to make my code symbolicated ... I read the part "below" : Given a crash report, the matching binary, and its .dSYM file, symbolication is relatively easy. The Xcode Organizer window has a tab for crash reports of the currently selected device. You can view externally received crash reports in this tab - just place them in the appropriate directory. This is the same as the Mac OS X directory described in the first section. It doesn't matter which device you have tethered, but the directory in which you place the crash report must be the directory for the tethered and selected device. It is not necessary to place the binary and .dSYM file in any particular location. Xcode uses Spotlight and the UUID to locate the correct files. It is necessary, though, that both files be in the same directory and that this directory is one that is indexed by Spotlight. Anywhere in your home directory should be fine. But it doesn't work for me ... here is what I did : I opened xcode organizer and I had my iphone device with crash logs App and dsym files are in my xcode project which is on my desktop All the rest should be automatic, right ? but crash logs aren't symbolicated yet ... Any comments welcome. Cheers. Gotye.

    Read the article

< Previous Page | 744 745 746 747 748 749 750 751 752 753 754 755  | Next Page >