Search Results

Search found 2690 results on 108 pages for 'ping pong'.

Page 76/108 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >

• What special configuration is needed to have a domain controller with DNS on a VM in Hyper-V?

  - by Michael J. Gray

  I have a server running Windows Server 2012 and it only has the Hyper-V role. I have a VM also running Windows Server 2012 and it has the Active Directory: Directory Services and DNS ([example.com]) roles. It has been promoted to a domain controller for [example.com]. In the virtualization host I have joined the domain successfully. On a laptop on the network, it can ping my DNS that is inside the VM on the virtualization host. However, it can't resolve anything through the DNS. I figured it was a firewall issue where the DNS had the firewall allow rule, but the virtualization host did not. I added that, but it didn't fix the issue. On my laptop, I get "UnKnown can't find [example.com]: No response from server" immediately. There's no time out, it just comes back right away. What have I overlooked?

  Read the article

• Why can't I access the WebUI of my DNS-323 NAS after a firmware upgrade?

  - by anonymous2

  Hi Everyone, I just bought a D-Link DNS-323 NAS Enclosure, and have run into a problem. I read that the firmware that had shipped with (1.07) did not support 2TB drives, so I downloaded firmware 1.08. Turned on the device for thwe first time and went straight to the WebUI (everything looked/worked fine) Proceeded with the firmware update, completed successfully. Rebooted and I cannot access the WebUI. I can see the NAS connected via my router interface I can also ping the ip adress assigned, but I cannot access the WebUI or find it via D-Link easy search software. I have tried the factory reset button, but that does not seem to be doing anything, the square blue light just keeps flashing from the moment the unit is powered on, whether I press the reset button or not, and the symptoms remain the same... PS. I did/do not have any drives installed yet. Please help?

  Read the article

• Windows Internet Connection Issue (HELP)

  - by semajjames1399

  I have a windows 8 hp dual booting ubuntu. When i log onto windows i cant get on the internet... But skype and other applications can just now webpages in a browser what so ever (this is on windows 8). But on ubuntu i have no internet issues at all. From what i see right now its only the browsers in windows 8 that cant get the internet, and ive tried all the browsers i had (chrome, ie, firefox) and they cant connect but in the win8 notification area it says im connected. I can even ping via cmd. HELP! Thanks. Whats not working is that i cant get access the internet through the windows 8 broswer.

  Read the article

• How can I solve Windows PPTP VPN issues?

  - by Robin M

  I'm having persistent problems with Windows PPTP VPN connections. The VPN appears up whilst the tunnel won't transfer traffic (ping to a remote IP within the VPN works for a while, and then fails). The client receives routing information via DHCP. When the connection fails, the routing table is still correct so I don't think it's a routing problem. My internet connection is via an ADSL2 line. There's software to deal with PPTP problems, like TunnelRat, but I don't want to install v1.1 of the .NET framework and I'd rather get to the bottom of the problem (I have multiple VPN connections and some are more unreliable than others). What can I do to get to the bottom of this? Alternatively, what can I do to keep the connection alive?

  Read the article

• Workgroup connection: You may not have permission

  - by Afiefh

  I have two Windows XP computers connected through an Ad-Hoc network, computer A creates the network and B connects to it. Both computers are on the Mshome network and have file and printer sharing enabled, and they can ping one another through the adhoc network. The result is that computer A can see computer B, but B cannot see A in the workgroup. But when A tries to access B I get a "you might not have permission to access" error telling me to contact the administrator. I tries to google the error, but most posts talk about problems connecting different versions of Windows to each other. I tried turning off the firewalls on both machines and checking if the required services are running. Nothing helped. Please excuse my ignorance on Windows networking, I haven't used Windows in around 10 years.

  Read the article

• Computer connects to lan, but not the internet

  - by Jay

  I have a computer with Vista Home that can connect to the router, but it cannot get on the internet. I cannot ping google.com, the request times out. I've tried this on two separate networks and have no trouble with other computers connecting. I've renewed ipconfig, reset winsock, updated the wireless adapter, and the hosts file looks fine. I've tried disabling the firewall as well as a direct wired connection. I did a scan with Norton and it didn't find anything. Is there anything else I can try before resorting to a system restore? Update (Copied from Answer) Windows Update was able to find updates and install them (though, they could have already been downloaded previously). When I pinged Google by using their IP 66.102.9.103, it said it lost 25 percent of the packets. I successfully flushed the DNS but it didn't help. Also, I found safe mode with networking works fine.

  Read the article

• How to reply some request from which routes its came from?

  - by tacoen

  I wonder if we can reply some request from which route its came from? My Situation is like this: eth0 192.168.10.1 --> gw: 192.168.10.254 nm: 24 eth1 192.168.11.1 --> gw: 192.168.11.254 nm: 24 Since this two IP is on the same machine, normally when we ping to 192.168.11.1 from 192.168.10.2. This machine will not reply to 192.168.10.2 because 192.168.10.0/24 it's on eth0, and the packets where requested via eth1. Can I make it works? I'm using Linux ubuntu, and the application will be listen to eth1 only.

  Read the article

• DHCP server can't see other machines

  - by William

  Hi, I setup a private network from virtual machines and one of the machines is the DHCP server for the group. I want to specify a next-server for the DHCP server but I'm having trouble connecting to any of the machines that I lease IPs to. I'm just trying to do a simple ping/ssh to 10.0.0.252 (a machine with a lease) but it doesn't seem to respond. Any advice? I'm assuming I need to be able to connect to my next-server but maybe I'm wrong. Thanks.

  Read the article

• How to set up VPN connection? Virtual Box 3.1.4 installed. Host - Snow Leopard(Mac) Guest - Windows 7 (32-bit)

  - by user31954

  I have Virtual Box 3.1.4 installed. Host - Snow Leopard(Mac) Guest - Windows 7 (32-bit). I have installed Windows on my MAC because I need it for work. I cannot establish VPN connection (using NAT). I tried to use bridged adapter, and I lost my internet connection on my guest(wind7) completely. I don't know much about networking, so I need detailed instructions for his particular OSs. Could someone please help me with this? Some random details about my attempts: On my host Windows I get error 800 trying to VPN. I can ping server address from my guest Win 7 and I have VPN connection established from my host Mac. I do disable VPN on my Mac when tying to establish it through guest. I tried to VPN from Mac and see if Guest sees it. It doesn't. Thank you!

  Read the article

• Sync Linux to Windows 2003/2008 Natively

  - by user26753

  Without using any external packages for Windows, can Linux synchronise it's clock to a Windows 03/08 Server natively? I've tried it using various NTP packages for Windows but would like to use just Windows software for this. EDIT: I've tried the below however it doesn't work. I've put TimeSource in /etc/hosts, stated server TimeSource in /etc/ntp.conf however when I do a service ntpd start it doesn't sync (it's 3 minutes out at the minute). I then stopped the NTPD and did a ntpdate TimeSource, thinking it would sync and then I'd start the NTPD once it's got the time, and it says: no server suitable for synchronization found. Though I can ping it. Any thoughts?

  Read the article

• trying to set up wireless router, failing

  - by j j

  Hi, I am trying to set up Netgear's wireless-n WNR2000 router, following their oversimplified 5- step process for plugging in wires, and I'm not having any success. It comes down to: once everything is wired and turned on in the correct order, all of the LEDs match the image they give of 'what should be lit up', but their setup disk still doesn't find the router. They have a site to set up the router manually, www.routerlogin.net, which I cannot navigate to, even while wired directly to the router. http://192.168.1.1 doesn't connect to anything, either. The interesting part: i get ping replies from Google's DNS server at 8.8.8.8 while this is set up. but cannot connect to any web site by name, since the router's DNS isn't set up. One thought is that the router and modem both have the same IP address, so it's conflicting, but I'm not sure how I'd resolve that. Any ideas?

  Read the article

• linux static ip problem

  - by out_sider

  I have a serve running centOS and I'd like to have the following setup: The server needs to have a static ip and be accessible by name. What I want is independently of the network being able to connect the server to the network and access it by name on Firefox as it will be running a web page. I tried setting the ip manually but while the inet addr is set as I want it the Bcast isn't. And I only can ping the server on the Bcast ip and because it is 192.168.2.255 ssh says it's not valid.

  Read the article

• Can't connect to server from certain machines

  - by Joel Coel

  On a small college campus we have a VLAN setup for the computer labs. These machines get assigned IP addresses in the 192.168.7.xxx range. In the server room, all of the server are on the default VLAN and assigned an IP address in the 10.1.1.xxx range. For the most part this works, but the lab machines are unable to connect to one of the servers. They can't even ping it. They can talk to other servers on the same switch as this server just fine. At first I thought it might be a vlan issue, but I changed the server port vlan to match other known-working ports with no effect. Any ideas?

  Read the article

• How can I tell if a host is bridged and acting as a router

  - by makerofthings7

  I would like to scan my DMZ for hosts that are bridged between subnets and have routing enabled. Since I have everything from VMWare servers, to load balancers on the DMZ I'm unsure if every host is configured correctly. What IP, ICMP, or SNMP (etc) tricks can I use to poll the hosts and determine if the host is acting as a router? I'm assuming this test would presume I know the target IP, but in a large network with many subnets, I'd have to test many different combinations of networks and see if I get success. Here is one example (ping): For each IP in the DMZ, arp for the host MAC Send a ICMP reply message to that host directed at an online host on each subnet I think that there is a more optimal way to get the information, namely from within ICMP/IP itself, but I'm not sure what low level bits to look for. I would also be interested if it's possible to determine the "router" status without knowing the subnets that the host may be connected to. This would be useful to know when improving our security posture.

  Read the article

• Mac | Router not assigning the IP address.

  - by Vaibhav Bajpai

  I recently installed Mac OS X 10.6, however the ethernet state is down. The assigned IP is 169.x.x.x. When booted the live USB of Ubuntu, I properly get an IP assigned in the range 192.168.1.x from the router 192.168.1.1 I am using the same router and same ethernet line. I tried to ping to 192.168.1.1 from my Mac and I get a host down message. I tried to manually assign the IP and set the router IP to 192.168.1.1 but still the router is unreachable.

  Read the article

• Ubuntu Wired network(ethernet does not work)

  - by user36777

  It was working just fine, until the other day I yanked it out. The wireless works just fine on the same router. If I login to a windows 7 instance on this dual boot laptop then the ehternet works just fine. So it's not a hardware, cable or router issue. The card even gets an ip, but I can't connect to the internet. Here are the details from route, iptables, ifconfig, ping etc. Any ideas? I have been struggling with this for day, none seems to have an answer. http://pastie.org/954816

  Read the article

• Why can't I access a webserver through a load balancer on my local network?

  - by Karptonite

  When I try to use curl (or wget, lynx, etc) to connect from a server on our local network to our website, which is on a local server behind a CoyotePoint load balancer, curl fails. Ping does not have this problem. When I curl directly to any of the servers behind that load balancer (from and to the same local network), I also have no problem. It doesn't matter whether the local server I'm curling from is behind the load balancer or not. Does anyone have any idea why I can't access my webserver through the load balancer on my local network?

  Read the article

• Error code 0x80070035. The network path was not found

  - by user144606

  My system is connected with a local LAN connection with 30 PC's. I'm not able to access the shared drive in the network, but I'm able to ping the IP address in which the drive is present. I have checked to start all the services, which are to be started and i have check the TCP/UDP ports also, but even after that I'm not able to access the drive, the same error message is being displayed again and again. Please help me to rectify the problem. I'm trying to solve the problem for the last 1 week. I have tried various solutions which are present in various web site, but I'm not able to find a proper solution. So please help me.

  Read the article

• Setting primary IP for VPS (out of 2 available)

  - by Flyer

  I've got a little problem. My VPS (Debian box) has 1 primary IP address, but now my hosting provider decided to assign me another one due to problems with first one. Let's say new IP is 91.222.152.20 and old one 91.221.190.170. How should I make 91.222.152.20 primary one, so that everything works on this address instead of 91.221.190.170 (like ftp, mysql etc) I tried editing /etc/newtwork/interfaces setting iface eth1 inet static address 91.222.152.20 netmask 255.255.252.0 network 91.222.152.0 broadcast 91.222.155.255 gateway 91.222.152.1 I know that network is 91.222.152.0/22 so I assume that above configuration should be right. Saved, rebooted and that ended pretty bad. Couldn't even ping box on old or new IP. Had to revert to working one. So question is. What am I doing wrong and how to do it right?

  Read the article

• Destination host unreachable

  - by user1010101

  I have 2 router connected to 1 switch which contains two vlans, 1 router has the ip table of vlan1 and the other router have the ip table of vlan2 I have trunked both router cable to the switch. I have set 1 ip table per router which correspond to the ip address of the PC that have this router address as a gateway. When I ping from 192.168.100.2 to 192.168.200.2 it tells me that destination host is unreachable and the message is from the router 192.168.100.1. So I guess router for 192.168.100.x does not see the router for 192.168.200.x , right ? Or am I wrong ? What are good troubleshooting steps ? http://i.imgur.com/b94Ir.png is the representation of the network, i cannot post image since im not reputated enough.

  Read the article

• Second vm not connecting to internet KVM

  - by potsed

  I cannot connect a second VM to the internet. I have two VM's set up and running, the first vm can connect to the Internet fine, the second does not even get a ping through. They are both set up in the same way with the same base packages but different secondary packages. Different sized disks etc. I am a noob with VM and perhaps I am missing something very simple. Like maybe that they have the same mac address or something. They are both using a bridged connection. Any help would be appreciated, and if you need logs please let me know which ones.

  Read the article

• Cannot access internal network on OSX 10.6.6

  - by cabuki

  Last week, I began having trouble connecting to our internal web servers. Usually, a refresh would take care of it or switching to a different wireless network, but as of yesterday, this wasn't enough. We have an internal DNS server using dnsmasq and a private internal host name (us.lcl). Once I started having more issues with the names not resolving, I tried pinging the server. Using the internal host name (s1.us.lcl), it failed. I tried using the IP address, but that also failed. I have no problems accessing external sites with the exception of it being a bit slower than normal. A reboot yesterday at lunch time after following the instructions here seemed to fix the issue, but when I came into the office this morning, it had stopped working. As of this posting, I cannot ping, ssh or access the web server using the internal host name or ip address. I'm the only one running 10.6 in my office and none of my colleagues has this issue.

  Read the article

• SFTP sending files between laptops on Ubuntu

  - by twigg

  I want to transfer files between two Ubuntu systems using SFTP. I have got it set-up and I can connect to the other laptop, ping it and see its file list using sftp> dir. I can see the files on the other system. But when I call get filename.deb it comes up saying Fetching /home/user/filename.deb to filename.deb 0% 0 0.0KB/s --:-- ETA and then drops back to the sftp command promote without transferring anything. Have I missed something?

  Read the article

• Why can't my FreeBSD 6.1 (vmware player client under Win7) do DNS in Bridged mode.

  - by Walter Stickle

  I have a 64-bit FreeBSD 6.1 client, running under Windows 7 (64-bit) via VMWare player 3.0, with networking set to bridge mode. DHCP goes fine on boot... I get correct adress/gateway/nameserver info... I have good connectivity to the world in that I can ping any host I can name by IP addr, (including both of the nameservers in resolv.conf,) ...but I can't resolve any names. Inside the Windows box, the network interface has VMWare Bridge Protocol enabled, and the windows side of things has full connectivity. dig replies with: ;; connection timed out; no servers could be reached ...even if I use "dig @server_ip_addr" to point it at a pingable, working nameserver If I set VM networking to NAT mode, I can get outbound connectivity (with happy DNS) but, of course, can't do INBOUND connectivity, which I need. Thoughts?

  Read the article

• Network share not always available

  - by CapSoft

  Hello everybody, we have a windows 2003 server with a shared directory. I've seen this thread but this wasn't any help: http://superuser.com/questions/58890/the-specified-network-name-is-no-longer-available I have a ping -t running from 3 pc's (vista and two windows 7) they all work. the things appear when two users enter the network share then this 'network share is no longer available' appears and the explorer windows turn white. after f5 or refresh the shared directory is back. this is really strange. there is no anti virus or kasparsky running on either end. this is all in a LAN. the internet connection is really stable, so it's really strange can it be a router issue? I have checked the eventlog on the server for diskfailure related messages, but there are none.

  Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >