Search Results

Search found 20671 results on 827 pages for 'android device'.

Page 767/827 | < Previous Page | 763 764 765 766 767 768 769 770 771 772 773 774  | Next Page >

• hp DL380 G4 won't boot with disk plugged into front USB

  - by Kev

  We outgrew a few older external USB backup drives, and purchased WD My Passport 1 TB USB 3.0 drives to replace them. When they are plugged into the front of our G4, it will blink forever after the BIOS (which is current, BTW) and never boot, even though the USB disks are not "bootable" per se. Our old drives did not exhibit this behaviour (so I don't think it's this type of issue that I've read about other servers.) The old drives were USB 2.0, but this shouldn't make a difference, AFAICT--the specs say all of the G4's USB ports are the same, 2.0, anyway, so I'm not sure how one port would handle a USB 3.0 device better than another. If we plug the new drives in one of the back slots, it boots fine. What's the cause? My concern is that the front USB port, and possibly the motherboard, might be starting to die. (We are experiencing other strange issues with them, or were initially, like intermittent file permissions errors despite wide-open ACL on these local drives, but some serverfault users have me convinced they may be coincidental software/security related issues.)

  Read the article

• How do I register a service with Bonjour?

  - by Roman

  I am trying to start to use Bonjour. Here I found a manual how to register a service with Bonjour. The following is written there: The network services architecture in Bonjour includes an easy-to-use mechanism for publishing, discovering, and using IP-based services. Well let's see how to register a service. In the very beginning it is written: To publish a service, an application or device must register the service with a Multicast DNS responder But how?!?! First of all I do not know what is the Multicast DNS responder. Second, it is not written how do I do it. Where and what should I type? Should I use command line? Should I use some programming languages? What exactly should I type... Is there an easy way to start to use Bonjour? Well, it was emphasized several times how easy it should be to use it. But I cannot start to use it for several day. So, can anybody, pleas, help me with that?

  Read the article

• lsof not showing what port a proc is listening on

  - by ericslaw

  I have many processes on a box listening on several ports. I am trying to map ports to pids. The problem is that lsof is not telling me what ports belong to which process. Given an apache listening on port 80, I can see it listening via netstat: user@host% netstat -an|grep LISTEN|grep 80 *.80 *.* 0 0 49152 0 LISTEN But when I try to map port 80 to a pid I get nothing: user@host% lsof -iTCP:80 -t When I try seeing what sockets that specific pid is using I get: user@host% lsof -lnP -p31 -a -i COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME libhttpd. 31 0 15u IPv4 0x6002d970b80 0t0 TCP *:65535 (LISTEN) Notice the *:65535 in the NAME column. Does anyone know why lsof is not reporting the port in use? I am running as root. I am using a mix of lsof and os versions: lsof v4.77 on Solaris10 sparc lsof v4.72 on Redhat4.2 etc I know that linux solutions can use "netstat -p", so I guess I'm only looking for why solaris isn't working, but I find lsof is frequently silent and not showing me expected data.

  Read the article

• Determining the Source of a Given File System Mount on Unix [migrated]

  - by phobos51594

  Background Recently I have run into a bit of a snag on my home FreeBSD server. I recently upgraded it to the latest stable release, and I have noticed some strange behavior with the /var partition. Originally, I had the system configured such that /var had its own partition with /var/run and /var/log in memory disks (/tmp, too). After the upgrade, I notice there is a new, fourth memory disk mounting directly to /var that I had not set up manually and is not in my fstab. It is only 28 megs or so in size and is causing problems when trying to update my ports collection. The ramdisk mounts atuomagically at boot and cannot be unmounted while in multi-user mode. If I drop to single user mode, I am able to unmount it without issue, however rebooting causes it to pop right back up. System specifications have been included at the end of the post. Question Is there any way to determine exactly what is mounting a given memory disk (or any filesystem, for that matter) after it has been mounted? Alternately, does anybody have any ideas what might have caused the new /var ramdisk to pop up? System Specification # uname -a FreeBSD sarge 9.1-PRERELEASE FreeBSD 9.1-PRERELEASE #0: Thu Nov 22 14:02:13 PST 2012 donut@sarge:/usr/obj/usr/src/sys/GENERIC i386 # df Filesystem 1K-blocks Used Avail Capacity Mounted on /dev/da0s1a 515612 410728 63636 87% / devfs 1 1 0 100% /dev /dev/da0s1d 515612 287616 186748 61% /var /dev/da0s1e 6667808 2292824 3841560 37% /usr /dev/md0 63004 32 57932 0% /tmp /dev/md1 3484 8 3200 0% /var/run /dev/md2 31260 8 28752 0% /var/log /dev/md3 31260 512 28248 2% /var <-- This # cat /etc/fstab # Device Mountpoint FStype Options Dump Pass# /dev/da0s1a / ufs rw,noatime 1 1 /dev/da0s1d /var ufs rw,noatime 2 2 /dev/da0s1e /usr ufs rw,noatime 2 2 md /tmp mfs rw,-s64M,noatime 0 0 md /var/run mfs rw,-s4M,noatime 0 0 md /var/log mfs rw,-s32M,noatime 0 0 Thank you in advance for any assistance.

  Read the article

• How do you recreate the System Recovery environment in Windows 7?

  - by Howiecamp

  I'm running Windows 7 Home Premium RTM (64-bit) and I want to take advantage of the system recovery tools (eg the Command Prompt) without using the Windows 7 DVD. My understanding is that this environment (WinRE) should be installed to your HDD by default as part of the Windows 7 installation. However, when I hit F8 on boot and select "Repair", I get: Windows failed to start. A recent hardware or software change might be the cause. To fix the problem... Status: 0xc000000e Info: The boot selection failed because a required device is inaccessible. The "Info" line seems like the smoking gun. My next step was to boot from the Windows 7 DVD, and choose "Repair". It indicated my Recovery Environment wasn't on the Windows 7 boot menu (perfect) and offered to fix it. I said yes and rebooted, however same issue as above. In addition, when I booted in to Windows 7 and I looked at the boot menu options, the recovery/repair option was not there. Only my Windows installation. Finally, I ran the Disk Management tool (diskmgmt.msc) and took a look at the contents of my "System Reserved" partition (which was set to "Active" as normal). It's unclear to me what the contents should look like, however it is my understanding that the WinRE environment gets installed to this partition. (As part of the above troubleshooting I followed http://superuser.com/questions/25728/how-to-fix-windows-7-boot-process which lead to http://www.sevenforums.com/tutorials/668-system-recovery-options.html).

  Read the article

• Wireless disconnects every 30 minutes

  - by Kez

  I have had a look through all the related questions and I get the feeling my problem is unique. My wireless connection disconnects every 30 minutes, for maybe 1 to 3 seconds. If I am browsing the web while it happens, I get the page cannot be displayed error message. I have checked the event logs as I was curious to know if there was anything in there. There is. Event 8033: BROWSER - The browser has forced an election on network \Device\NetBT_Tcpip_{B919CC30-25A9-45DD-A09F-549A6262FC9E} because a master browser was stopped. Reported exactly every 30 minutes which coincides with my wireless problem. I am running Windows 7 Ultimate, 32-bit. My wireless is Realtek RTL8187 integrated into a ASUS P5K-E/Wifi motherboard. It is on a workgroup and has never been on a domain. This problem does not affect any other computers. Wireless reception is great, and I have ensured that the wireless unit is transmitting on a frequency not used by any nearby wireless basestations. How can I fix this pesky problem?

  Read the article

• Is VGA port hot-pluggable?

  - by Martin Bøgelund

  In meetings, I often see people detaching the VGA connector from one running laptop and connecting it to another, while the projector is still on. Is this 100% risk free, and OK by design of the VGA standard? If there's a risk involved in hot-plugging VGA, can it be removed by turning off or suspending either laptop, display, or both? I see this being done all the time without causing disaster, so clearly I'm not interested in answers stating "we do it all the time, so it should be OK!". I want to know if there's a risk - real or in theory - that something breaks when doing this. EDIT: I did an internet search on the topic, and I never found a clear statement as to why it is safe or unsafe to hot swap VGA devices. The typical form is a forum question asking basically the same question as I did, and the following types of statements Yes it's hot swappable! I do it all the time! It involves some kind of risk, so don't do it! You're some kind of moron if you think there's a risk, so just do it! But no explanation as to why it safe or not... Joe Taylors answer below contains a link to a forum post and answers that basically give me the same statements as mentioned above. But again, no good explanation why. So I looked for an actual manual for a projector, and found "Lenovo C500 Projector User’s Guide". It states on page 3-1: Connecting devices Computers and video devices can be connected to the projector at the same time. Check the user’s manual of the connecting device to confirm that it has the appropriate output connector. [image] Attention: As a safety precaution, disconnect all power to the projector and devices before making connections. But again, no good explanation.

  Read the article

• How do I restore a Windows Server 2008 R2 bare metal backup to a Windows Server 2012 R2 Hyper-V instance?

  - by Michael J. Gray

  I have been trying to find a simple way to migrate a physical Windows Server 2008 R2 installation over to a virtual machine hosted on Windows Server 2012 R2 Datacenter Edition /w Hyper-V. I came across the bare metal backup feature on Windows Server 2008 R2 and assumed I would be able to easily back it up and simply restore it into a new virtual machine by booting the installation media and getting into the Windows recovery process. When I attempted this, Hyper-V got into a network based restore process, but I do not have a PXE server or anything like that and I would rather not set it up. I tried mounting the VHD produced in the bare metal backup, just to see if it would somehow work, but it of course did not and failed with an error related to an incorrect boot device. I checked the virtual machine's BIOS settings and everything looked fine. I did not expect this to work anyway, so I stopped working through this method any further. Is there a way to take my bare metal backup and restore it into a virtual machine without a PXE server or SCVMM? I am opening to using proprietary tools but since the last time I did this I used Norton Ghost, which is no longer supported, I figured I would try doing it with what is readily available.

  Read the article

• JVM disappeared on Mac OS X Snow Leopard 10.6.8

  - by weisjohn

  I'm working in Eclipse one night, (also using Android's DDMS from the commandline). The next morning, I open the lid... attempt to run Eclipse and get an error. me$ sudo /Applications/eclipse/eclipse JavaVM: requested Java version ((null)) not available. Using Java at "" instead. JavaVM: Failed to load JVM: /bundle/Libraries/libserver.dylib So I then attempt to find out where my JDKs are pointed: me$ ls -la /System/Library/Frameworks/JavaVM.framework/Versions/ total 64 drwxr-xr-x 12 root wheel 408 Nov 16 10:44 . drwxr-xr-x 12 root wheel 408 Sep 7 09:39 .. lrwxr-xr-x 1 root wheel 5 Sep 7 17:07 1.3 -> 1.3.1 drwxr-xr-x 3 root wheel 102 Dec 2 2009 1.3.1 lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.4 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.4.2 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.5 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.5.0 -> CurrentJDK lrwxr-xr-x 1 root wheel 10 Sep 7 17:07 1.6 -> CurrentJDK drwxr-xr-x 9 root wheel 306 Nov 16 10:44 A lrwxr-xr-x 1 root wheel 1 Sep 7 17:07 Current -> A lrwxr-xr-x 1 root wheel 59 Sep 7 17:07 CurrentJDK -> /System/Library/Java/JavaVirtualMachines/1.6.0.jdk/Contents Everything looks normal so far... me$ ls -la /System/Library/Java/JavaVirtualMachines/ total 0 drwxr-xr-x 2 root wheel 68 Nov 16 10:44 . drwxr-xr-x 5 root wheel 170 Nov 16 10:44 .. Apparently, my virtual machines have been deleted or moved? I'll probably be able to just re-install Java, but does anyone have any insight into why this may have happened or how to prevent in the future?

  Read the article

• Ubuntu 12.04/12.10 can't detect windows or any other partitions(Asus z77 UEFI BIOS)

  - by user971155

  I've recently completed tinkering my new pc(motherboard ASUS z77 with UEFI BIOS) and unfortunately not everything works quite well. After installing windows 7 ultimate on a single primary partition(SATA drive) I decided to allocate one more logical partition for additional needs. When I tried doing it with the manager - it said that it couldn't allocate requested size even though I certainly asked for much less than it was available. I thought that it might have been a windows issue and proceded to installing Ubuntu 12.10 x64. When the graphical interface loaded it showed me a message stating that it can't find any other operating system on the drive. When I used custom partioning option it showed me none of my current partions(including that with windows). However, when I boot with "Try Ubuntu" feature it does find them ! I find it weird though. Here's what the console present me with: ubuntu@ubuntu:~$ sudo os-prober /dev/sda1:Windows 7 (loader):Windows:chain ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00072b98 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 100020223 49906688 7 HPFS/NTFS/exFAT /dev/sda3 100022270 1250263039 575120385 5 Extended /dev/sda4 566669312 1250263039 341796864 83 Linux I also tried creating partitions from disk utility which results in error: , Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=51211402240, size=1923000000, type=0x83 Entering MS-DOS parser (offset=0, size=640135028736) MSDOS_MAGIC found looking at part 0 (offset 1048576, size 104857600, type 0x07) new part entry looking at part 1 (offset 105906176, size 51104448512, type 0x07) new part entry looking at part 2 (offset 51211402240, size 588923274240, type 0x05) Entering MS-DOS extended parser (offset=51211402240, size=588923274240) readfrom = 51211402240 MSDOS_MAGIC found Exiting MS-DOS extended parser looking at part 3 (offset 290134687744, size 349999988736, type 0x83) new part entry Exiting MS-DOS parser MSDOS partition table detected containing partition table scheme = 1 got it Error: Can't have overlapping partitions. ped_disk_new() failed Here's what I get when I try to install the system i.stack.imgur.com/pjlb9.png, i.stack.imgur.com/g1lXN.png P.S. It's strange that I even can't create any more partitions neither with disk-utility nor with windows 7 native tools

  Read the article

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• Ubuntu 12.04 open port 80 inside WLAN

  - by Eduard

  I have an nginx server running on ubuntu 12.04 that serves http through port 80 and https through port 443. Everything works fine if I access it from the same computer via localhost, 127.0.0.1 or the local IP 192.168.0.11. If I try to access the server from another computer in the same VLAN it does not work for http; it works for https. I have changed my nginx configuration to also listen to port 8000 for http; I can then access http from the other computer in the same VLAN via "http://192.168.0.11:8000". I also have a web server running on port 80 on a windows machine and can access it from another device in the same VLAN, therefore the router is not blocking incoming http traffic. The nginx process is run by root. I have used tcpdump and I see that packets are arriving to Ubuntu: 192.168.0.16.49735 192.168.0.11.80 and that some response is being given 192.168.0.11.80 192.168.0.16.49735 (I do not know what the response is though). There is no request arriving at the nginx web server (I have checked the access log). I have iptables empty. I have unsuccessfully tried to find a solution for a long time to this, it has now become a matter of happiness or bitterness :).

  Read the article

• Windows VPN for remote site connection drawbacks

  - by Damo

  I'm looking for some thoughts on a particular way of setting up a estate of machines. We have a requirement to install machines into unmanned, remote locations. These machines will auto login and perform tasks controlled from a central server. In order to manage patching, AV, updates etc I want these machines to be joined to a dedicated domain for this estate. Some of the locations will only have 3G connectivity (via other hardware), others will be located on customer premises in internal networks. The central server (of ours) and the Domain Controller will be on a public WAN. I see two ways of facilitating this. Install a router at each location and have a site to site VPN between the remove device and the data centre where the servers are location Have the remote machine dial up and authenticate via a Windows VPN connection to the DC via RAS Option one is more costly to setup and has a higher operational cost. It also offers better diagnostics if the remote PC goes down. Option two works well but is solely dependent on the VPN connection been made before any communication can be made to the remote machine. In a simple test, I can got a Windows 7 machine to dial a VPN prior to authentication to a domain, then automatically login to the machine using domain credentials. If the VPN connection drops, it redials. I can also create a timed task to auto connect every hour in case of other issues. I'd like to know, why (if at all) is operating a remote network of devices which are located in various out of band locations in this way a bad idea? Consider 300-400 remote machines all at different sites. I'd rather have 400 VPN connections to a 2008 server than 400 routers, however I'd like to know other opinions on this.

  Read the article

• Recover data from a Thecus N4100 NAS jbod partition

  - by TimothyP

  I have a Thecus N4100 NAS wich had a 2TB drive in it configured as jbod partition. Later I tried adding a second drive to expand the available space. I added it to the jbod configuration but I did not get any extra space. Then I tried removing the second drive but then the NAS system indicated the jbod configuration was damaged. After a reboot it told me there is no configuration and I need to create a new RAID/jbod configuration and that I would lose all data on the drive. Of course I did not do this, I took the 2TB drive and checked with Linux if the partition was still there and it is... completely intact. I found that linux recognizes it as a /dev/mdX device and that I should be able to mount it but I don't know the file system type. Anyway.... is there a way to recover the data? Since everything has always been on a single drive it should all be there right? I can connect the drive to Windows , Linux or MacOS so whatever gets the job done.

  Read the article

• How do I install Windows XP from an external hard drive?

  - by Plasmer

  I'm trying to install Windows XP Media Center edition by copying the install disc image to an external hard drive and making it bootable. Has anyone had success getting this to work on systems that can't boot from dvds/floppies? I'm basically working from this guide: http://www.dl4all.com/other/21495-install-windows-xp-from-usb.html Update - 2/15/10 I used WinToFlash on my laptop to format my usb hard drive from my install dvd (Windows XP Media Center Version 2005 with Update Rollup 2 from Dell) and selected "boot from usb device" at the boot selection menu and the windows installer started up. However, an error message came up saying that: "A problem has been detected and windows has been shut down to prevent damage to your computer." Originally on my desktop machine, I had 1 150Gb SATA drive, and 2 150 Gb SATA drives striped together using RAID. From the hard drive diagnostics, it appears the windows install on one of the RAIDed disks lost a block and this has been preventing me from booting up. I replaced the standalone drive with a new 1Tb SATA drive and disconnected the other hard drives. Could the message be indicating a virus is on the unformatted drive? or the usb hard drive? Update 2 - 2/15/10 The external hard drive didn't find any viruses when scanned. I tried installing Vista Home Premium 64bit SP1 using WinToFlash and that installed successfully onto the new 1Tb drive. WinToFlash was really easy to use and helped a lot, thanks!

  Read the article

• Monitor displays at 1024x768; scrolls screen for higher resolutions

  - by Matt

  I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks

  Read the article

• Ext3 fs: Block bitmap for group 1 not in group (block 0). is fs dead?

  - by ip

  My company has a server with one big partition with Mysql database and php files. Now this partition seems to be corrupted, as reported from kernel messages when I tried to mount it manually: [329862.817837] EXT3-fs error (device loop1): ext3_check_descriptors: Block bitmap for group 1 not in group (block 0)! [329862.817846] EXT3-fs: group descriptors corrupted! I've tried to recovery it running tools from a PLD livecd. These are the tools I have tested: - e2retrieve - testdisk - photorec - dd_rescue/dd_rhelp - ddrescue - fsck.ext2 - e2salvage without any success. dumpe2fs 1.41.3 (12-Oct-2008) Filesystem volume name: /dev/sda3 Last mounted on: <not available> Filesystem UUID: dd51610b-6de0-4392-a6f3-67160dbc0343 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal filetype sparse_super Default mount options: (none) Filesystem state: not clean with errors Errors behavior: Continue Filesystem OS type: Linux Inode count: 9502720 Block count: 18987570 Reserved block count: 949378 Free blocks: 11555345 Free inodes: 11858398 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 16384 Inode blocks per group: 512 Last mount time: Wed Mar 24 09:31:03 2010 Last write time: Mon Apr 12 11:46:32 2010 Mount count: 10 Maximum mount count: 30 Last checked: Thu Jan 1 01:00:00 1970 Check interval: 0 (<none>) Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 128 Journal inode: 8 Journal backup: inode blocks dumpe2fs: A block group is missing an inode table while reading journal inode e2fsck 1.41.3 (12-Oct-2008) fsck.ext3: Group descriptors look bad... trying backup blocks... fsck.ext3: A block group is missing an inode table while checking ext3 journal for /dev/sda3 I tried also backup superblocks, same error result. There's any other tools I have to test before considering these disk definitely unrecoverable? Many thanks, ip

  Read the article

• Once VPN connection is done, how do I proceed reaching the other side address space?

  - by sports

  I'm using Windows Azure and I created a VPN Site To Site, configured like this: My virtual network: My address space: 10.2.0.0/16 (65531) Subnet1: 10.2.1.0/24 (251) Subnet2: 10.2.2.0/24 (251) Gateway: 10.2.3.0/29 (3) My public gateway IP: 137.135.x.z (I wont show x and z for security reasons) This public gateway uses, as you can see, 5 IPs on subnet1 and 5 IPs on subnet2, and 5 IPs on the gateway "Their" virtual network (in azure this would be a "Local network") Their address space: 172.60.100.67/32, 172.60.100.68/32, 172.60.100.69/32 Their device public IP: x.x.x.x (ommited for security reasons) Notice their address space are 3 IPs So: the VPN is "in green" (in Azure is showing up green, literally, like these two are connected) and now my question is: How do I proceed to reach their address space? I've tried creating a virtual machine (Windows Server 2008, but it could be an Ubuntu) on "my" virtual network and it is automatically "placed" on subnet1 or subnet2. So it gets the IP 10.2.1.0 (valid example), I can't choose to place the virtual machine in the gateway address space. How do I "reach" any of the IPs 172.60.100.67, 172.60.100.68, 172.60.100.69 ? In other words: How can I telnet any of these IPs? or ping? or see them in my network? Please provide me answers for Windows Server 2008 or for an Ubuntu. I'm open to create any virtual machine.

  Read the article

• Cut (smart edit) .mts (AVCHD Progressive) files un Ubuntu Lucid

  - by pts

  I have a bunch of .mts files containing AVCHD Progressive video recorded by a Panasonic camera, and I need software on Ubuntu Lucid with which I can remove the boring parts, and concatenate the interesting parts, all this without reencoding the video stream. It's OK for me to cut at keyframe boundary. If Avidemux was able to open the files, it would take about 60 hours of work for me to cut the files. (At least that was it last time I tried with similar videos, but of a file format supported by Avidemux.) So I need a fast, powerful and stable video editor, because I don't want that 60 hours of work go up to 240 or even 480 hours just because the tool is too slow or unstable or has a terrible UI. I've tried Avidemux 2.5.5 and 2.5.6, but they crash trying to open such a file, even if I convert the file to .avi first using mencoder -oac copy -ovc copy. mplayer can play the files. I've tried Avidemux 2.6.0, which can open the file, but it cannot jump to the previous or next keyframe etc. (if I make it jump to the next keyframe, and then to the previous keyframe, it doesn't end up at the original keyframe, sometimes displays an error etc.). Also I'm not sure if Avidemux 2.6.x would let me save the result without reencoding. I've tried Kdenlive 0.7.7.1, but playback is very choppy, and it cannot play audio at all (complaining that SDL cannot find the device; but many other programs on the system can play audio). It would be a pain to work with. I've tried converting the .mts file to .mkv using ffmpeg -i input.mts -vcodec copy -sameq -acodec copy -f matroska output.mkv, but that caused too much visible distortions in the video in both mplayer and Avidemux. I've tried converting the .mts file with TsRemux.exe, but Avidemux 2.5.x still can't open that file. Is there another program to cut and concatenate the files? Is there a preprocessor which would create a file (without reencoding the video) on which Avidemux wouldn't crash?

  Read the article

• Ubuntu won't boot from USB memory stick

  - by mackenir

  I used the instructions on this webpage to create a bootable USB drive for running Ubuntu 9.10. Unfortunately it doesn't work on my EeePC. Even with 'Removable Dev.' selected in the BIOS as the first boot device, the PC just boots into Windows 7. How do I troubleshoot this problem? The drive is readable and looks like this: Directory of E:\ 28/10/2009 21:14 <DIR> .disk 28/10/2009 21:14 222 README.diskdefines 28/10/2009 21:14 143 autorun.inf 28/10/2009 21:14 <DIR> casper 28/10/2009 21:14 <DIR> dists 28/10/2009 21:14 <DIR> install 28/10/2009 21:14 <DIR> syslinux 28/10/2009 21:14 4,098 md5sum.txt 28/10/2009 21:14 <DIR> pics 28/10/2009 21:14 <DIR> pool 28/10/2009 21:14 <DIR> preseed 28/10/2009 21:14 0 ubuntu 26/10/2009 16:16 1,468,640 wubi.exe 25/02/2010 00:28 2,147,483,648 casper-rw 8 Dir(s) 5,290,307,584 bytes free

  Read the article

• Remote Desktop Zooming

  - by codeulike

  Using Remote Desktop from a device with a hi-res screen (say, a Surface Pro) is decidedly tricky - as everything displays 1:1 scale and so looks tiny. If the machine you are remoting into runs Server 2008 R2 or later, you can change the dpi zooming setting (see here). But for older hosts, that doesn't work. Using normal Remote Desktop, you can connect with a lower resolution, say 1280x768, and turn on smart-sizing. However smart-sizing can scale down (to display a huge desktop in a small area) but does not seem to scale up (to display a small desktop in a big area). Using the Windows 8 Remote Desktop App, you can zoom - but you cannot set the default resolution of the host. What I want is a lower resolution in the host, scaled up to fit my screen. So both of those are close to what I want, but dont quite work. So question is: Does the Remote Desktop App allow screen resolution to be set somehow? Is there some other Remote Desktop client that can handle zooming better?

  Read the article

• NTOP gives warnings on startup

  - by FR6

  I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

  Read the article

• How to display escaped characters in tmux status bar

  - by walrus

  i am running tmux from a tty on an embedded linux device. (NOT a terminal emulator) because the screen is rather small, i want to add some "icons" to the tmux status bar. to achieve this, i have simply created a font with the appropriate glyphs for things like battery, or wifi. i can load the font, and display the characters with calls that use an escape to the line drawing characters like so: echo -e "\xe\234\xf" \xe escapes me into line drawing character mode, \234 is my created character, and \xf returns me to normal character mode so my terminal doesnt start getting goofy. this works perfectly if i enter the command at the terminal whether tmux is started or not. the issue arises if i then try to use it in my ~/.tmux.conf file for the status bar. i currently have a line like this: set -g status-right "#(echo -e "\xe\234\xf") #(/script/to/output/powerlevel) this simply outputs \xe\234\xf powerlevel this goes the same if i try printf over echo. this is the output i would expect to get on the terminal if i made the call without passing -e to echo, or without enclosing the statement with quotes. i then decided to wrap the calls to the echo or printf in a shell script. again, the script works when called from the terminal, but not in tmux's status bar. now i get the unprintable character "?" instead of my icon, like this: ? powerlevel this is what i would expect if i did not use the line drawing escapes previously mentioned above, or if i tried to copy and paste the character as text using tmux. in addition, the calling of these character scripts screws up the rest of my status-right, as the clock has about 6 digits for minutes when it is called (though it correctly only updates two of them). how can i make tmux respect the escape characters? any help or insight is greatly appreciated.

  Read the article

• Problem in accessing Windows shared folder on Ubuntu using terminal

  - by vikramtheone

  Hi Guys, Description I have 2 systems with me, one running on Windows(Host) and one on Ubuntu, both on a LAN. On the Windows(Host) I develop software intended for the Linux system and because the Linux system has little external memory, my idea to overcome this is by making the project folder on the Host side a Shared Folder with full access and access it on Ubuntu over the network. To achieve this, I have installed Samba on Ubuntu, when I go to Places -> Network I can see the shared project folder and I simply mount it. A link appears on the desktop. Next, using Nautilus I open the link and I can access the contents of the shared folder. Problem Even though I mount the shared project folder, I don't see it appearing in the /media or the /mnt folder, as a result of this I don't know what path to use to access this folder, from the terminal. For example: When, I mounted my USB stick, as expected, a link for the device appears on the Desktop and I also see a folder in the media folder. So, similarly, a mounted shared folder should have appeared on the /mnt folder, too. Can anyone suggest what I should do now? There are many posts around, but no solid solution for this problem. Help!!! :) Vikram

  Read the article

• How do you notice that the batteries of you wireless mouse are dying out?

  - by hkBattousai

  I have a Logitech M705 wireless mouse. I'm first time using a wireless mouse, so I don't have much experience with the hardware features and behavior. It is rated that it runs for 3 years with the same batteries. I think this "3 year" rating is calculated for a very low usage and activity; like 2 hours a day. I'm using it for about 12 hours a day, so I expect it to run out of batteries in a much shorter time in my case. I have been using it for about half a year. Recently (for the last two weeks), it started to make some peculiar behavior when clicking and drafging objects. - When I click something, it sometimes double click it. - When I drag something from one place to another (or selecting some text), it sometimes drops the object in the halfway (when selecting text, the text which had selected up to that time becomes unselected and it starts to select the rest of the text from that moment), but it goes on being in the "left-button-pressed" state. It is like, the pressed button switches to "unpressed" state for a moment, then returns back to the "pressed" state. When one of these faults occur, it occurs several times sequentially. There is no problem in pointer movement, scrolling or right-clicking. Since the batteries last for a very long time for this device, I don't expect it to stop working in an instance. I expect it to give these kind of syndromes of a time period. My question is; Is this how batteries run out for a wireless mouse? Or, is this another kind of hardware/software problem?

  Read the article

< Previous Page | 763 764 765 766 767 768 769 770 771 772 773 774  | Next Page >