Search Results

Search found 3312 results on 133 pages for 'freebsd ports'.

Page 77/133 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

• FTP error 424 failed to establish connection

  - by cKK

  Getting "ftp error 425 failed to establish connection" when trying to connect to ftp server. Tried 2 ftp clients on 3 machines on same network and none work. However FTP works from home / mobile broadband. No ip blocks on ftp sever. Other ftp servers(differrent ip/hosts) work okay. firewall setup correct, no ports blocked. Is it possible to use a proxy for ftp a i think it's something with the ISP but taking too long to fix?

  Read the article

• virtualbox ftp hangs on list command

  - by Tiddo

  Hi all, I have virtual box installed on a windows 7 64-bit computer, with Cent OS 5.5 as guest os. I want to be able to use ftp between those. I've installed vsftpd on the guest os, and the guest os uses a nat connection with the host os for internet. So far, I am able to connect to the guest os using ftp (in filezilla), but after the list command is executed, nothing happens, until the command is timed out. This happens in both active and passive mode. I do have set a pasv_min/max_port in the vsftpd.conf file, listing is enabled, and the ports are redirected in virtualbox. Also the ftp_data_port is set to 20. I also tried setting the pasv_address, but I had to set it to 127.0.0.1, but than filezilla gives me this: Command: PASV Response: 500 OOPS: bad family Command: PORT 127,0,0,1,139,204 Response: 500 OOPS: child died Can someone help me with this?

  Read the article

• PSAD Firewall/ UDP flood?

  - by Asad Moeen

  Well I'm actually trying to block a UDP Flood on the Application port because the string "getstatus" is causing my application to make large output due to a small input to the attacker's IP. I installed PSAD firewall to do the job. psad -S shows 3000,000 logged packets at the application port and top ports in Scan but does not block the IP of the attacker however other IP Addresses with small number of connections are dropped. I'm thinking that since output is also being made to the attacker, this is why its not getting blocked because iptables rate-limiting is also exactly doing the same thing and not blocking the IP where outgoing connection is also made. Any guesses why it won't work?

  Read the article

• Management VLAN Cisco Catalyst

  - by cha789

  I have configured a couple of VLANs on a Cisco Catalyst switch, i will put all the ports that clients is connected to, into these VLANs. I want to configure the native VLAN [vlan 1] as management VLAN so i can use a telnet client to connect to the switch. How can i block all but one specific IP-address to telnet into the switch? As i understand vlan 1 has many task regarding different protocols and i do not want to break that but only allow one specific IP-address to connect to the switch with a telnet client [actually the gateway ip address of the switch].

  Read the article

• Improving server security [closed]

  - by Vicenç Gascó

  I've been developing webapps for a while ... and I always had a sysadmin which made the environment perfect to run my apps with no worries. But now I am starting a project on myself, and I need to set up a server, knowing near to nothing about it. All I need to do is just have a Linux, with a webserver (I usually used Apache), PHP and MySQL. I'll also need SSH, SSL to run https:// and FTP to transfer files. I know how to install almost everything (need advice about SSL) with Ubuntu Server, but I am concerned about the security topic ... say: firewall, open/closed ports, php security, etc ... Where can I found a good guide covering this topics? Everything else in the server... I don't need it, and I wanna know how to remove it, to avoid resources consumption. Final note: I'll be running the webapp at amazon-ec2 or rackspace cloud servers. Thanks in advance!!

  Read the article

• HP ProLiant DL320e G8 v2 - USB2.0 during POST

  - by user3513346

  Initially my USB2.0 ports were working during POST (and boot). However, now they appear not to be. I first noticed this when I could not access the RBSU by pressing F9 during POST. Then found that I couldn't boot from USB either (I was able to do both of these initially). When performing the boot via iLo remote console I can access all of the setups (i.e., all of the F(X)'s) and can boot virtual media from a 'removable drive'. Keyboard works fine once the OS is booted. Not really sure what to try here. Any advice would be greatly appreciated. Thanks. Nick.

  Read the article

• OSX Parallels 5 - can't share internet connection when using host-only networking...

  - by Steve Kirtley

  I've just upgraded from Parallels 3 to Parallels 5, but am having a problem matching my previous configuration. I am a web developer so run a local web server on my mac. I used to allow access to this from the virtual machines in Parallels by using 'Host-Only Networking' and then in OSX enabling internet sharing from my wifi/ethernet to the virtual ethernet ports that Parallels created. The setup was based on: http://www.craigfrancis.co.uk/features/setup/parallels/ The new version of Parallels doesn't create any network adaptors that are available for internet sharing in OSX - just VNIC's which only show under an ifconfig... Can anyone suggest how to make this all play nice? Thanks in advance! Steve

  Read the article

• Copy files between two windows machines on seperate domains

  - by Simon

  I need to copy several database backups between two computers. The source computer initiates the copy and is a Windows 2000 pc and is a member of domain1. The destination machine is running Windows Server 2000 and is a member of domain2. The machines are on separate networks physically connected via a firewall. The files are currently copied via ssh with http://sshwindows.sourceforge.net/ installed on the destination machine. There is no need to encrypt the contents during the copy, however the passwords should not be sent in the clear. I am looking for a way to copy the files without having to install a server on the destination. I specifically need help with how to set up the permissions and what ports would need to be opened on the firewall.

  Read the article

• Remote connection to dynamic public ip & private ip addresses

  - by user53864

  Many times I connected to windows computer which has static public ip address via remote desktop over wan links. I'm wondering how could I connect to the remote computer that has dynamic public ip address & private ip addresses assigned. I've 2 systems at home: xp system-------connected to internet(dynamic public ip) & allowed other users to connected to the internet on the interface. windows vista system--------enabled dhcp on the interface to access internet from xp. How could I remotely connect from my office to the 'vista system'?. If I've a router/modem at my home it may be possible to allow the ports for the system but I don't. Any tips?

  Read the article

• Windows 2008 Routing and Remote access server - access to the internet

  - by Ian

  I have a windows 2008 r2 remote access server set up and running. The remote access works fine. My problem is that the remote access server itself doesn't have access to the internet. The box has two interfaces, an internal and an external. Inbound connections come in on the external interface and RRAS responds. All wall and nice. I want to be able to use windows update, browse, etc from this box but can't as the outbound traffic just gets blocked. I've tried going into the RRAS mmc tool and opening the interface properties, under which there are two buttons for inbound and outbound filters. There I tried adding ports 80 and 443, but this doesn't work completely. I can see the connection initiating (Syn goes out) but the session never establishes itself. Anyone done this or got any suggestions?

  Read the article

• IP camera's multicast/RTSP conflicting with 2.4GHz Wi-Fi?

  - by jayson

  Here at our business we have a Netgear R7000 running DD-WRT. I have been slowly adding IP cameras which I run using Blue Iris software. The last camera I bought (which is NOT a wireless camera), when I plug it into the network I start having really bad connection issues on the 2.4GHz Wi-Fi network. The 5GHz works fine, just the 2.4GHz all of the sudden has trouble connecting, as if it's conflicting. I've tried playing with the camera settings, different IP addresses, HTTP ports, etc, and discovered it to be a conflict with multicast. When multicast is checked, the Wi-Fi has issues but my video streams via Blue Iris. When unchecked, Wi-Fi works fine but the video won't stream through Blue Iris. The problem is there are no settings in the camera to change the RTSP port, which is set to 34567. Does anyone know something that could fix this issue? It all seems very strange to me but maybe someone has an idea?

  Read the article

• Cannot assign port 4 to WAN on TP-Link WR740N by DD-WRT wiki

  - by Victor Sergienko

  I'm following the DD-WRT instruction to get TP-Link WR740N v3's Port 4 on a different VLAN, but this doesn't happen. First, I have no "Setup VLANs" settinngs tab in DD-WRT v24-sp2 (07/20/12) std r19519. I can get Internet on Wi-Fi if assigning eth1 to "WAN Port", but then all Ethernet ports get on the same VLAN and any wired connection grabs the DHCP address and Internet connection from router. When following the "old" instruction, if I run, say, nvram set vlan2ports="2 5*", should there appear a new interface, vlan2, in ifconfig, after ifconfig vlan2 up? It doesn't - does it mean there is no support for different VLANs in my software/hardware? What am I missing? Is it impossible to create more VLANs on TP-Link740?

  Read the article

• CA and VPN setup

  - by Raj

  We are a small comany about 20 employees. We have some off site some i houser servers. Where should I install CA? On a domain controller or VM? can I obtain my own certificate for MS VPN? Where should I install MS vpn server? can I install on VM CA server? Do I need to open any ports on Firewall? Please send me or direct me to a web site where I can get setip by step installation instructions. Thanks.

  Read the article

• Static Route Qestion

  - by mrlayance

  I have a Wan simulator between 2 networks. I can ping both networks from the wan simulator, but I can not ping from one network to the other. testr01 Fa0/0 10.0.0.1/24 FA0/1 192.168.0.1/30 | | Wan Sim 2 nics Eth0 192.168.0.2/30 | Eth1 192.168.1.2/30 | | testr02 Fa0/1 192.168.1.1/30 Fa0/0 10.1.0.2/24 I can not figure out what type of routes I need. On the route? On the Server? I guess all 10. traffic to the Fa0/0 ports? Thanks

  Read the article

• NFS Datastore Appears Empty!

  - by daemonchild

  Hi guys, I've got an NFS server problem. The datastore connected and seems to be a valid datastore in both the vSphere client and under /vmfs/volumes. The issue is that it appears to be empty! I can create files (eg: touch /vmfs/volumes/nfs_common/thefile) and it is correctly written to the nfs store. I can verify this by looking on the nfs server itself. But the vmkernel only sees an empty datastore; the file disappears. Another freebsd box can mount the same NFS share and see the files correctly. Some useful data: ESXi 4.0.0 Build 208167 NFS is unfsd running on a Buffalo Linkstation Pro Duo (a bit hacky I know). The share has file system permissions set to 777 at the moment. My /etc/exports is as follows, and as I say it connects fine. /mnt/array1/ESX_Shared 192.168.16.0/255.255.255.0(insecure,rw,sync,no_root_squash,no_subtree_check) The ESXi servers can also successfully mount NFS shares from other NFS servers. Any ideas guys? Thanks, Tom

  Read the article

• How to set up wireless access on a Cisco router

  - by Carlos

  Hi, I've set up my 877W according to the configuration listed in this forum post: IPTV over Cisco 877 (It's the working configuration at the bottom of the post) Note that I have an 877W, so it also has a wireless radio. Now, I've gotten the whole setup to work, so IPTV is working, and I can access the internet via the ethernet ports. Now I'm trying to figure out how to allow access via the dot11radio interface. I've gathered that I basically need to create a bridge group, and bridge the radio to the internet VLAN. However, when I add a bridge-group 2 command to VLAN1, it seems to take down the whole internet VLAN. (The IPTV continues to work.) This makes the router itself inaccessible (I've got a laptop, so no serial) and I end up having to reboot the router. Can anyone tell me how to a) Allow wireless access to the internet (preferably with WEP, to match my old router) b) Determine what makes the router inaccessible when I add the new bridge group c) Forward the IPTV traffic onto a machine on my internet VLAN

  Read the article

• MAC to IP binding in ASA 5510 / SG 300-52

  - by Sampsa

  I am trying to configure a Cisco ASA 5510 to assign specific IP-addresses to specific MACs. Firmware on my ASA is 8.2(5). I have used this feature in our previous device (Cisco SA-520W). I have also read that this feature is (not yet) implemented. How do I work around this problem, if not by direct assignment? Do I need to specify fixed IP's on concerned devices themselves? I also have a SG 300-52 switch for our LAN. We cannot specify IP-addresses to ports, because we have further switches down the line. Thank you for your help!

  Read the article

• Configuring vsftpd with nginx on ubuntu

  - by arby

  I have vsftpd installed on Ubuntu 12.04LTS along with nginx, php, and sql on an Amazon ec2 instance. The web server is good to go, but I'm having trouble connecting to the FTP server. I'm not quite sure how to set the privileges or what configuration options I might be missing. By default, the location of the web root is at /usr/share/nginx/www and it is owned by root:root. The web server runs as user www-data in the group www-data. I've opened port 21 and set the passive ports in the ec2 backend and ufw firewall. In vsftpd.conf, I have: ... anonymous_enable=NO local_enable=YES local_umask=0027 chroot_local_user=YES pasv_enable=YES pas_max_port=12100 pasv_min_port=12000 port_enable=YES ... Now, I'm unsure how to create the FTP user that when I login, displays my web directory with write access. I've tried it a few different ways, but I keep running into errors (either no connection, no write access, or very slow timeouts.)

  Read the article

• mystery Internet traffic to port 445

  - by Ben Collver

  Recently, I noticed traffic from the office network to TCP port 445 on the Internet [a]. Below are the Linux firewall log entries to Facebook's network [b] and Google's network [c]. I would like to identify the source of this traffic. My first guess is that Facebook and Google might be using multiple TCP ports for SSL load balancing. However, I could not confirm this based on the web proxy logs. What else might it be? [a] http://support.microsoft.com/kb/204279 [b] Sep 4 08:30:03 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.131 DST=69.171.237.34 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=14287 DF PROTO=TCP SPT=51711 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0 [c] Aug 28 06:02:41 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.115 DST=173.194.33.47 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=4558 DF PROTO=TCP SPT=49294 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0

  Read the article

• How to achieve reliable Gigabit Ethernet Link with my Acer Aspire Revo R3610?

  - by The Operator

  I want to stream HD movies over my wired Gigabit LAN from my PC to my Acer Aspire Revo R3610. It's connected with a 3ft Cat5e patch cable to my Netgear GS605v2 Switch. The PC acting as File Server is connected at 1Gbps to the Switch. Network driver options are set to defaults, including automatic speed/duplex negotiation on both machines. The Revo will not connect to my Network Switch at 1Gbps - the OS reports that it reverts to 100Mbps either shortly after connection or immediately upon connection. Through a process of elimination (trying different drivers, patch cables, ports on the switch, and other 1Gbps-capable devices connected to the Network switch which successfully achieve 1Gbps links and performance) I have drawn the conclusion there is either a Hardware or Software (Driver) issue with the Revo itself. I have performed tests using Windows 7 and Ubuntu 9.10. Can anyone offer insight on Gigabit Ethernet with the Revo?

  Read the article

• On Mikrotik RouterOS, is it possible to get Netflow information from a bridged connection?

  - by Tim

  I have a RouterOS box set up to bridge two ethernet connections. I have use-ip-firewall=yes in the bridge configuration, so that the ports go through the firewall. I've enabled netflow reporting via ip/traffic-flow, but the only packets I see reported are broadcast and multicast packets, not the packets that are flowing through the bridge. The documentation indicates that traffic flow logging happens after firewall processing and that it won't work with bridged connections by default, but I would have thought that use-ip-firewall=yes ought to address this. Is it possible to make this work somehow?

  Read the article

• AWS EC2: How to determine whether my EC2/scalr AMI was hacked? What to do to secure it?

  - by Niro

  I received notification from Amazon that my instance tried to hack another server. there was no additional information besides log dump: Original report: Destination IPs: Destination Ports: Destination URLs: Abuse Time: Sun May 16 10:13:00 UTC 2010 NTP: N Log Extract: External 184.xxx.yyy.zzz, 11.842.000 packets/300s (39.473 packets/s), 5 flows/300s (0 flows/s), 0,320 GByte/300s (8 MBit/s) (184.xxx.yyy.zzz is my instance ip) How can I tell whether someone has penetrated my instance? What are the steps I should take to make sure my instance is clean and safe to use? Is there some intrusion detection techinque or log that I can use? Any information is highly appreciated.

  Read the article

• Too many connectons to 212.192.255.240

  - by Castor

  Recently, my Internet slowed down drastically. I downloaded a tool to see the TCP/IP connections from my Vista computer. I found out that a lot TCP/IP connections are being connected to 212.192.255.240 through SVCHost. It seems that it is trying to connect to different ports. I think that my computer is being infected with some kind of malware etc. But I am not sure how to get rid of it. I did a little bit of research on this IP but found nothing. Any suggestions are highly apprecitated.

  Read the article

• Better logging for cronjob output using /usr/bin/logger

  - by Stefan Lasiewski

  I am looking for a better way to log cronjobs. Most cronjobs tend to spam email or the console, get ignored, or create yet another logfile. In this case, I have a Nagios NSCA script which sends data to a central Nagios sever. This send_nsca script also prints a single status line to STDOUT, indicating success or failure. 0 * * * * root /usr/local/nagios/sbin/nsca_check_disk This emails the following message to root@localhost, which is then forwarded to my team of sysadmins. Spam. forwarded nsca_check_disk: 1 data packet(s) sent to host successfully. I'm looking for a log method which: Doesn't spam the messages to email or the console Don't create yet another krufty logfile which requires cleanup months or years later. Capture the log information somewhere, so it can be viewed later if desired. Works on most unixes Fits into an existing log infrastructure. Uses common syslog conventions like 'facility' Some of these are third party scripts, and don't always do logging internally. UPDATE 2010-04-30 In the process of writing this question, I think I have answered myself. So I'll answer myself "Jeopardy-style". Is there any problem with this method? The following will send any Cron output to /usr/bin//logger, which will send to syslog, with a 'tag' of 'nsca_check_disk'. Syslog handles it from there. My systems (CentOS and FreeBSD) already handle log rotation. */5 * * * * root /usr/local/nagios/sbin/nsca_check_disk 2>&1 |/usr/bin/logger -t nsca_check_disk /var/log/messages now has one additional message which says this: Apr 29, 17:40:00 192.168.6.19 nsca_check_disk: 1 data packet(s) sent to host successfully. I like /usr/bin/logger , because it works well with an existing syslog configuration and infrastructure, and is included with most Unix distros. Most *nix distributions already do logrotation, and do it well.

  Read the article

• connect to paltalk server using a proxy

  - by user40026

  Hi I want to use paltalk, which is a kind of chat software, but the ports that this applications uses are closed in my country. What I need to do is to use a proxy server. Unfortunately the software itself does not provide a proxy setting. I though it would be possible to run paltalk on an O.S. installed on a virtual machine (say virtualbox) and configure the network setting of virtual machine to direct all its traffic through a proxy on host Operating system, but I could not find a way to do so neither. can anyone please help me?

  Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >