Search Results

Search found 47090 results on 1884 pages for 'linux ubuntu customize'.

Page 77/1884 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

• Our embedded linux system won't recognize a USB Device if it is plugged in before powerup. Suggestions?

  - by Blaine

  We are developing on a small embedded device. This device us a gumstix overo board running OpenEmbedded linux. We have our development almost completely done, and have run into the strangest of bugs that we can't figure out. We have a USB Device (Spectrophotometer) that has a USB2.0 Connection and an external power supply for the light source. Typical behavior is that you plug in the power supply, then the USB connection to a host. When the usb connection is detected by the device, the device boots up and enables the light source and fan. The device is then able to be used by the host system. The problem is that if the device is plugged into the Gumstix before we turn on the Gumstix, the USB Device apparently is not probed by the system (and hence does not turn on). Under a normal situation, when the connection is initialized by plugging in the usb cable, the spectro turns itself on and becomes available to the system (this can be seen via "lsusb" typically). Neither of these things are happening. There is no device detected via "lsusb" and no dmesg errors of any kind that we can see. It is as if the device is not plugged in. The device does show up and work fine if we unplug the USB cable and plug it back in once the system is booted up. It turns on and shows up on the usb bus, and we can access it with our driver. On any other desktop or laptop, it does not matter if the host system is on or off when we plug in the spectrometer. This behavior is what I would consider to be "normal" - that the usb system is probed and initialized at boot time, and the usb devices come online. In other words, our system is fully functional as long as we plug in the usb device after the system is booted up. Unfortunately this isn't possible in our final product - everything comes on at once. Additional Info: 1) We have tried a flash drive attached to the system when the system is turned off. Booting up the system brings the flash drive online, as expected 2) There are no messages regarding the spectro or usb device (using dmesg). "lsusb" only lists the USB hubs / controllers. It is literally as if the device is not present and not plugged in. 3) We have tried a brand new image from gumstix and an older image from last year. Both images have this problem. This problem exists on all 3 gumstix devices we use. Does anyone have any suggestions? From what I can tell it isn't really possible to do a complete "reboot" of the usb system that is a complete emulation of "unplugging" and "replugging" a usb device. I feel like what is happening is that there is no initial probe on the usb bus that would trigger the usb handshaking, but this is somehow specific to the spectro. This seems to be a kernel issue or at least an issue in how the kernel is initializing the usb subsystem. I'm not really sure though. I have tried the gumstix mailing list, but there doesn't seem to be anyone who has seen this issue before. Any advice or suggestions on where to start looking would be fantastic. Thank you! Blaine output etc. $ uname -a Linux overo 2.6.33 #1 Tue Apr 27 08:35:38 PDT 2010 armv7l GNU/Linux When the system is up and running and spectro is plugged in (working as intended), this is lsusb: Bus 001 Device 116: ID 2457:1022 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x2457 idProduct 0x1022 bcdDevice 0.02 iManufacturer 1 USB4000 1.01.11 iProduct 2 Ocean Optics USB4000 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 46 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 400mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 4 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) dmesg output: usb usb1: usb auto-resume hub 1-0:1.0: hub_resume usb usb2: usb auto-resume ehci-omap ehci-omap.0: resume root hub hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 hub 2-0:1.0: hub_resume hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000 hub 1-0:1.0: hub_suspend usb usb1: bus auto-suspend hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend ehci-omap ehci-omap.0: suspend root hub usb usb2: usb resume ehci-omap ehci-omap.0: resume root hub hub 2-0:1.0: hub_resume ehci-omap ehci-omap.0: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT hub 2-0:1.0: port 2: status 0501 change 0001 hub 2-0:1.0: state 7 ports 3 chg 0004 evt 0000 hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: new high speed USB device using ehci-omap and address 2 ehci-omap ehci-omap.0: port 2 high speed ehci-omap ehci-omap.0: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT usb 2-2: default language 0x0409 usb 2-2: udev 2, busnum 2, minor = 129 usb 2-2: New USB device found, idVendor=2457, idProduct=1022 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: Ocean Optics USB4000 usb 2-2: Manufacturer: USB4000 1.01.11 usb 2-2: uevent usb 2-2: usb_probe_device usb 2-2: configuration #1 chosen from 1 choice usb 2-2: uevent usb 2-2: adding 2-2:1.0 (config #1, interface 0) usb 2-2:1.0: uevent drivers/usb/core/inode.c: creating file '002' dmesg has nothing to say, and lusb simply lists nothing else but the two default usb controllers / hubs if we plug the device in before the system is turned on.

  Read the article

• Ensure you have prerequisite rpms to install Oracle 10gR2 on Linux on IBM zSeries

  - by didier.wojciechowski

  To ensure you have installed the required rpms in order to achieve a sucessful installation of Oracle Database Server 10gR2. Oracle Support released this Metalink Note 1086769.1

  Read the article

• Ubuntu's Lucid Lynx: Ubuntu's Most Innovative

  <b>Datamation:</b> "Ubuntu&#8217;s Lucid Lynx (Ubuntu 10.04) is still six weeks away from release. However, on the eve of the first beta release, the daily builds and news releases suggest that Lucid will be one of the most innovative versions of Ubuntu for several years."

  Read the article

• Register for the Oracle VM & Oracle Linux Partner Day – 25th July, Oracle TVP Reading

  - by Cinzia Mascanzoni

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} This event has been set up for our partners to come along and understand more about an untouched opportunity to deliver data centre consolidation solutions for customers who run their business on Oracle software. There is clear message from end customers that virtualizing their tier 1, mission critical applications is high on the CIO’s agenda. Register now.

  Read the article

• Recommended language and IDE for simple linux application [on hold]

  - by niklon

  I want to write a simple program on Debian with Gnome. Application will act as a side bar, giving simple information on online servers statuses. I preferably have a black transparent background(Terminal-like). I'm asking this question because I was previously writing programs in .NET C# for myself, and now I don't want to get to Mono, but something more conventional. What language should I choose for this task? What would be the recommended way to do it?(eg. what IDE)

  Read the article

• Linux distro for software development support?

  - by Xie Jilei

  I've spent too much time on setup & maintain a development server, which contains following tools: Common services like SSH, BIND, rsync, etc. Subversion, Git. Apache server, which runs CGit, Trac, Webmin, phpmyadmin, phppgadmin, etc. Jetty, which runs Archiva and Hudson. Bugzilla. PostgresSQL server, MySQL server. I've created a lot of Debian packages, like my-trac-utils, my-bugzilla-utils, my-bind9-utils, my-mysql-utils, etc. to make my life more convenient. However, I still feel I need a lot more utils. And I've spent a lot of time to maintain these packages, too. I think there maybe many developers doing the same things. As tools like subversion, git, trac are so common today. It's not to hard to install and configure each of them, but it took a long time to install them all. And it's time consuming to maintain them. Like backup the data, plot the usage graph and generate web reports. (gitstat for example) So, I'd like to hear if there exist any pre-configured distro for Development Server purpose, i.e., something like BackTrack for hackers?

  Read the article

• How to Quickly Resize, Convert & Modify Images from the Linux Terminal

  - by Chris Hoffman

  ImageMagick is a suite of command-line utilities for modifying and working with images. ImageMagick can quickly perform operations on an image from a terminal, perform batch processing of many images, or be integrated into a bash script. ImageMagick can perform a wide variety of operations. This guide will introduce you to ImageMagick’s syntax and basic operations and show you how to combine operations and perform batch processing of many images. The HTG Guide to Hiding Your Data in a TrueCrypt Hidden Volume Make Your Own Windows 8 Start Button with Zero Memory Usage Reader Request: How To Repair Blurry Photos

  Read the article

• VMware Kernel Module Updater hangs on Ubuntu 13.04

  VMware Player has a nice auto-detection of kernel changes, and requests the user to compile the required modules in order to load them. This happens from time to time after a regular update of your system. Usually, the dialog of VMware Kernel Module Updater pops up, asks for root access authentication, and completes the compilation. VMware Player or Workstation checks if modules for the active kernel are available. In theory this is supposed to work flawlessly but in reality there are pitfalls occassionally. With the recent upgrade to Ubuntu 13.04 Raring Ringtail and the latest kernel 3.8.0-21 the actual VMware Kernel Module Updater simply disappeared and the application wouldn't start as expected. When you launch VMware Player as super user (root) the dialog would stall like so: VMware Kernel Module Updater stalls while stopping the services Prior to version 5.x of VMware Player or version 7.x of VMware Workstation you would run a command like: $ sudo vmware-config.pl to resolve the module version conflict but this doesn't work anyway. Solution Instead, you have to execute the following line in a terminal or console window: $ sudo vmware-modconfig --console --install-all Those switches are (as of writing this article) not documented in the output of the --help switch. But VMware already documented this procedure in their knowledge base: VMware Workstation stops functioning after updating the kernel on a Linux host (1002411). Update As of today I had the first kernel upgrade to version 3.8.0-22 in Ubuntu 13.04. Don't even try it without vmware-modconfig...

  Read the article

• IPC linux huge transaction

  - by poly

  I'm building and application that requires huge transactions/sec of data and I need to use IPC to for the mutithreaded mutliprocceses communication, I know that there are a lot of methods to be used but not sure which one to choose for this application. This is what the application is gonna have, 4 processes, each process has 4 threads, the data chunk that needs to be transferred between two or more threads is around 400KB. I found that fifo is good choice except that it's 64K which is not that big so i'll need to modify and recompile the kernel but not sure if this is the right thing to do? Anyway, I'm open to any suggestions and I'd like to squeeze your experience in this :) and I appreciate it in advance.

  Read the article

• How to Upgrade Ubuntu 9.10 (Karmic Koala) to Ubuntu 10.04 (Lucid Lynx) Desktop

  <b>Ubuntu Geek: </b>"This tutorial will explain How to Upgrade Ubuntu 9.10 (Karmic Koala) to Ubuntu 10.04 (Lucid Lynx) released on the 29th April 2010."

  Read the article

• Ubuntu Control Center (ucc) - Simple tool for ubuntu administration

  <b>Ubuntu Geek:</b> "Ubuntu Control Center or UCC is an application inspired by Mandriva Control Center and aims to centralize and organize in a simple and intuitive form the main configuration tools for Ubuntu distribution."

  Read the article

• Process monitoring in Linux environment?

  - by poly

  I'm trying to write a multi threaded/processes application and it need to know how to monitor a process from another process all the time. So here is what I have, I have a 2 processes, each with multiple threads that handle the network part, then another 2 process also with multiple threads that interact with DB and with the network processes, what I need to do is that if for example one of the network processes goes down the DB process start sending to the live network process until the second one is up again. I'm using fifo between the DB and the network process. I was thinking of sending messages with message passing all the time but not sure whether this is a good idea or I need to use some other IPC for this issue, or probably neither is good and I need to use entirely something else?

  Read the article

• Dual-boot more than two operating systems

  - by aldorado

  I currently run Windows 7 and Ubuntu 12.04 as a dual-boot system. I need Linux, but Ubuntu freezes at least once a day. So I want to replace it with another distribution like Debian or LMDE. On the other hand I am a little concerned that I'll have troubles working with a less user friendly operating system than Ubuntu. So would it be possible to just scale down the Windows partition and install the next Linux as a third system? Thus, with a "triple-boot system" I could keep Ubuntu until I feel familiar with the new system. Afterwards, I guess, it should be possible to replace the Ubuntu partition by expanding the new system?

  Read the article

• Cannot install g++ on ubuntu

  - by Erel Segal

  I don't have g++: erelsgl@ubuntu:/etc/apt$ which g++ erelsgl@ubuntu:/etc/apt$ erelsgl@ubuntu:/etc/apt$ g++ The program 'g++' can be found in the following packages: * g++ * pentium-builder Try: sudo apt-get install <selected package> So I try to install it: erelsgl@ubuntu:~/srilm$ sudo apt-get install g++ Reading package lists... Done Building dependency tree Reading state information... Done g++ is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 5 not upgraded. 2 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up g++ (4:4.4.3-1ubuntu1) ... update-alternatives: error: alternative path /usr/bin/g++ doesn't exist. dpkg: error processing g++ (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of build-essential: build-essential depends on g++ (>= 4:4.3.1); however: Package g++ is not configured yet. dpkg: error processing build-essential (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: g++ build-essential E: Sub-process /usr/bin/dpkg returned an error code (1) I also try to install build-essential, and get same results. I also tried "sudo apt-get update" - didn't help. This is my apt-cache: erelsgl@ubuntu:/etc/apt$ apt-cache policy g++ build-essential g++: Installed: 4:4.4.3-1ubuntu1 Candidate: 4:4.4.3-1ubuntu1 Version table: *** 4:4.4.3-1ubuntu1 0 500 http://il.archive.ubuntu.com/ubuntu/ lucid/main Packages 100 /var/lib/dpkg/status build-essential: Installed: 11.4build1 Candidate: 11.4build1 Version table: *** 11.4build1 0 500 http://il.archive.ubuntu.com/ubuntu/ lucid/main Packages 100 /var/lib/dpkg/status erelsgl@ubuntu:/etc/apt$ I also tried this and got the same error: erelsgl@ubuntu:~/Ace/Files/corpus$ sudo dpkg --configure -a Setting up g++ (4:4.4.3-1ubuntu1) ... update-alternatives: error: alternative path /usr/bin/g++ doesn't exist. dpkg: error processing g++ (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of build-essential: build-essential depends on g++ (>= 4:4.3.1); however: Package g++ is not configured yet. dpkg: error processing build-essential (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: g++ build-essential

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• Upgrade issues due to broken "dependency problems prevent configuration of linux-image-generic" error

  - by tsukune1791

  okay, I've recently upgrade from 11.10 to 12.04 and I've been having some issues. I don't know if its a bug or not, but I thought I would submit it here. Okay here's a little background; I ran the distro update from the update manager and got a couple errors that I didn't catch. the computer restarted, and when I logged the Launcher and my top bar of the Ubuntu desktop didn't load. While it was trying to load a couple error messages came up, I think they were called "apport", saying they couldn't send the bug information for some reason. I believe it said somethings wrong with my internet connection, but nothing's wrong with it. Anyway I tried running some things in terminal, namely sudo apt-get -f install sudo apt-get upgrade sudo apt-get dist-upgrade and keep getting the following errors; dustin@marceau-laptop:~$ sudo apt-get dist-upgrade [sudo] password for dustin: Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 4 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y Setting up initramfs-tools (0.99ubuntu13) ... update-initramfs: deferring update (trigger activated) Setting up linux-image-3.2.0-24-generic (3.2.0-24.37) ... Running depmod. update-initramfs: deferring update (hook will be called later) Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.2.0-24-generic /boot/vmlinuz-3.2.0-24-generic run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.2.0-24-generic /boot/vmlinuz-3.2.0-24-generic update-initramfs: Generating /boot/initrd.img-3.2.0-24-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.2.0-24-generic /boot/vmlinuz-3.2.0-24-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.2.0-24-generic /boot/vmlinuz-3.2.0-24-generic run-parts: executing /etc/kernel/postinst.d/zz-runlilo 3.2.0-24-generic /boot/vmlinuz-3.2.0-24-generic Fatal: No images have been defined. run-parts: /etc/kernel/postinst.d/zz-runlilo exited with return code 1 Failed to process /etc/kernel/postinst.d at /var/lib/dpkg/info/linux-image-3.2.0-24-generic.postinst line 1010. dpkg: error processing linux-image-3.2.0-24-generic (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of linux-image-generic: linux-image-generic depends on linux-image-3.2.0-24-generic; however: Package linux-image-3.2.0-24-generic is not configured yet. dpkg: error processing linux-image-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-generic: linux-generic depends on linux-image-generic (= 3.2.0.24.26); however: Package linux-image-generic is not configured yet. dpkg: error processing linux-generic (--configure): dependency problems - leaving unconfigured Processing triggers for initramfs-tools ... No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. update-initramfs: Generating /boot/initrd.img-3.2.0-24-generic Fatal: No images have been defined. run-parts: /etc/initramfs/post-update.d//runlilo exited with return code 1 dpkg: error processing initramfs-tools (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Errors were encountered while processing: linux-image-3.2.0-24-generic linux-image-generic linux-generic initramfs-tools localepurge: Disk space freed in /usr/share/locale: 0 KiB localepurge: Disk space freed in /usr/share/man: 0 KiB localepurge: Disk space freed in /usr/share/gnome/help: 0 KiB localepurge: Disk space freed in /usr/share/omf: 0 KiB localepurge: Disk space freed in /usr/share/doc/kde/HTML: 0 KiB Total disk space freed by localepurge: 0 KiB E: Sub-process /usr/bin/dpkg returned an error code (1) And my Ubuntu desktop is still not working. I can log into Gnome and Ubuntu 2D but the Launcher, I think it's call, doesn't load. Can someone help me fix these error, or point me in the right direction to get them fixed? It is much appriciated.

  Read the article

• How to customize the ubuntu gnome 3 desktop?

  - by Francesco

  This is maybe a stupid question, but how can I choose my own background image on ubuntu gnome 3?? I click on Settings - Background - then I click on the current background preview to change it but I see only the defaults images! No + symbol to add or something. On the 'Pictures' tab there is nothing to select, I get an empty white page? I am running ubuntu gnome 13.04 3.9.6-030906-generic. Thanks!

  Read the article

• How to customize live Ubuntu CD?

  - by karthick87

  I would like to customize Ubuntu live CD by installing some additional packages. I have followed this link but it doesn't seems to work. Can anyone provide clear instructions? Thanks in advance! Customization Packages that I want to install: Thunderbird Samba SSH Changes that I need: Remove Games menu from the Application menu Firefox shortcut on desktop Radiance as the default theme Different default Ubuntu wallpaper Note I do not prefer Remastersys, manual way will be appreciated.

  Read the article

• Ubuntu 12.04 updates fail recently - Please help

  - by user74152

  I upgraded Ubuntu 11.10 to 12.04 LTS immediately after its release (april 2012). Since then updates (new kernels and others) succeeded regularly, but recently, suddenly, updates fail consistently. What causes the problem and how can it be solved? Terminal information after the last update attempt: ariel@ariel-MS-7592:~$ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 3 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up linux-image-3.2.0-26-generic (3.2.0-26.41) ... Running depmod. update-initramfs: deferring update (hook will be called later) Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic update-initramfs: Generating /boot/initrd.img-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic /usr/sbin/grub-mkconfig: 11: /etc/default/grub: splash”: not found run-parts: /etc/kernel/postinst.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postinst.d at /var/lib/dpkg/info/linux-image-3.2.0-26-generic.postinst line 1010. dpkg: error processing linux-image-3.2.0-26-generic (--configure): subprocess installed post-installation script returned error exit status 2 No apport report written because MaxReports is reached already dpkg: dependency problems prevent configuration of linux-image-generic: linux-image-generic depends on linux-image-3.2.0-26-generic; however: Package linux-image-3.2.0-26-generic is not configured yet. dpkg: error processing linux-image-generic (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of linux-generic: linux-generic depends on linux-image-generic (= 3.2.0.26.28); however: Package linux-image-generic is not configured yet. dpkg: error processing linux-generic (--configure): dependency problems - leaving unconfiguredNo apport report written because MaxReports is reached already No apport report written because MaxReports is reached already Errors were encountered while processing: linux-image-3.2.0-26-generic linux-image-generic linux-generic E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• yum update works but yum --security update fails to work in Fedora 12

  - by bobo

  I had already installed the yum-security before. And I was going to do an update by entering the following command: [root@localhost /]# yum update Loaded plugins: presto, priorities, refresh-packagekit, security Skipping security plugin, no data Setting up Update Process Resolving Dependencies Skipping security plugin, no data --> Running transaction check ---> Package eject.i686 0:2.1.5-17.fc12 set to be updated ---> Package glibc.i686 0:2.11.1-4 set to be updated ---> Package glibc-common.i686 0:2.11.1-4 set to be updated ---> Package glibc-devel.i686 0:2.11.1-4 set to be updated ---> Package glibc-headers.i686 0:2.11.1-4 set to be updated ---> Package gnome-themes.noarch 0:2.28.1-3.fc12 set to be updated ---> Package gtk2.i686 0:2.18.9-3.fc12 set to be updated ---> Package gtk2-immodule-xim.i686 0:2.18.9-3.fc12 set to be updated ---> Package kernel-PAE.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-PAE-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-PAEdebug-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-debug-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-devel.i686 0:2.6.32.11-99.fc12 set to be installed ---> Package kernel-firmware.noarch 0:2.6.32.11-99.fc12 set to be updated ---> Package kernel-headers.i686 0:2.6.32.11-99.fc12 set to be updated ---> Package libnetfilter_conntrack.i686 0:0.0.101-1.fc12 set to be updated ---> Package media-player-info.noarch 0:5-1.fc12 set to be updated ---> Package nscd.i686 0:2.11.1-4 set to be updated ---> Package perf.noarch 0:2.6.32.11-99.fc12 set to be updated ---> Package rhythmbox.i686 0:0.12.6-5.fc12 set to be updated ---> Package sysvinit-tools.i686 0:2.87-3.dsf.fc12 set to be updated --> Finished Dependency Resolution --> Running transaction check ---> Package kernel-PAE.i686 0:2.6.31.12-174.2.3.fc12 set to be erased --> Finished Dependency Resolution Dependencies Resolved ================================================================================ Package Arch Version Repository Size ================================================================================ Installing: kernel-PAE i686 2.6.32.11-99.fc12 updates 20 M kernel-PAE-devel i686 2.6.32.11-99.fc12 updates 6.2 M kernel-PAEdebug-devel i686 2.6.32.11-99.fc12 updates 6.2 M kernel-debug-devel i686 2.6.32.11-99.fc12 updates 6.2 M kernel-devel i686 2.6.32.11-99.fc12 updates 6.1 M Updating: eject i686 2.1.5-17.fc12 updates 49 k glibc i686 2.11.1-4 updates 4.2 M glibc-common i686 2.11.1-4 updates 14 M glibc-devel i686 2.11.1-4 updates 953 k glibc-headers i686 2.11.1-4 updates 590 k gnome-themes noarch 2.28.1-3.fc12 updates 1.5 M gtk2 i686 2.18.9-3.fc12 updates 3.2 M gtk2-immodule-xim i686 2.18.9-3.fc12 updates 60 k kernel-firmware noarch 2.6.32.11-99.fc12 updates 968 k kernel-headers i686 2.6.32.11-99.fc12 updates 749 k libnetfilter_conntrack i686 0.0.101-1.fc12 updates 37 k media-player-info noarch 5-1.fc12 updates 32 k nscd i686 2.11.1-4 updates 189 k perf noarch 2.6.32.11-99.fc12 updates 79 k rhythmbox i686 0.12.6-5.fc12 updates 4.0 M sysvinit-tools i686 2.87-3.dsf.fc12 updates 58 k Removing: kernel-PAE i686 2.6.31.12-174.2.3.fc12 @updates 72 M Transaction Summary ================================================================================ Install 5 Package(s) Upgrade 16 Package(s) Remove 1 Package(s) Reinstall 0 Package(s) Downgrade 0 Package(s) Total download size: 75 M Is this ok [y/N]: But then I changed my mind, I decided to do a security-only update instead of a full update, so I entered the following command: [root@localhost /]# yum --security update Loaded plugins: presto, priorities, refresh-packagekit, security Setting up Update Process Resolving Dependencies Limiting packages to security relevant ones http://download.fedoraproject.org/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.cuhk.edu.hk/pub/linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.cuhk.edu.hk/pub/linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.cuhk.edu.hk/pub/linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.riken.jp/Linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.riken.jp/Linux/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirror.cse.iitk.ac.in/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirror.cse.iitk.ac.in/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirrors.isu.net.sa/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirrors.isu.net.sa/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. ftp://ftp.chu.edu.tw/linux/Fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno -1] Metadata file does not match checksum Trying other mirror. http://mirror.yandex.ru/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirror.yandex.ru/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://linus.iyte.edu.tr/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://linus.iyte.edu.tr/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.jaist.ac.jp/pub/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.jaist.ac.jp/pub/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.kddilabs.jp/Linux/packages/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://srv2.ftp.ne.jp/Linux/packages/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://www.ftp.ne.jp/Linux/distributions/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://srv2.ftp.ne.jp/Linux/distributions/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.rhd.ru/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.rhd.ru/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirrors.163.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirrors.163.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirror.nus.edu.sg/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirror.nus.edu.sg/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.yz.yamagata-u.ac.jp/pub/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.yz.yamagata-u.ac.jp/pub/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.linux.org.tr/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.linux.org.tr/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://mirrors.cytanet.com.cy/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://mirrors.cytanet.com.cy/linux/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://fedoramirror.hnsdc.com/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://fedoramirror.hnsdc.com/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.twaren.net/Linux/Fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://c147.twaren.net/pub/Linux/Fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.mirror.tw/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.mirror.tw/pub/fedora/linux/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ftp.cs.pu.edu.tw/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ftp.cs.pu.edu.tw/Linux/Fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. http://ubuntu.cn99.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz: [Errno 14] HTTP Error 416 : http://ubuntu.cn99.com/fedora/updates/12/i386/repodata/updateinfo.xml.gz Trying other mirror. Error: failure: repodata/updateinfo.xml.gz from updates: [Errno 256] No more mirrors to try. You could try using --skip-broken to work around the problem ^C[root@localhost /]# As it can be seen in the output, when I run the yum --security update command, it did show the Limiting packages to security relevant ones message so it's aware of the option. But I don't know why it keeps reporting the http error 416. I searched in google and found the following description of the error but it doesn't seem to help much. HTTP ERROR 416 - Requested Range Not Satisfiable A 416 status code indicates that the server was unable to fulfill the request. This may be, for example, because the client asked for the 800th-900th bytes of a document, but the document was only 200 bytes long. It suggests me to use the --skip-broken option, I tried and the output is the same. I already tested many times, it just doesn't work when the --security option is used. What could be the possible cause for this problem?

  Read the article

• LogMeIn Hamachi for Linux

  - by tlunter

  So far most of my work using LogMeIn Hamachi has been from either a Mac OS X or Windows system to Windows or a Linux Computer. Recently I purchased a mini computer and have been running Ubuntu Server on it, as my little server. I knew LogMeIn had a Linux client that is command line only, but I often do all my work via command line anyway, so that wasn't an issue. I added my user to the correct local file so that I could run the hamachi daemon without sudo, and was able to connect to LogMeIn's service. I decided to set up my Linux server as a git server as well, and set it up correctly. The thing is, the server is behind my schools firewall and I need to use hamachi to get around that. Since most of the time I was using either Mac or Windows, I never had an issue sshing onto any of my computers since LogMeIn is fully featured for these OSs. From Linux (Arch) though, it seems like the client cannot correctly route to the LogMeIn IPs. I know from Windows I can connect to the Linux computers, both of them. From Linux (Arch) though, I can't connect to my Mac, Windows, or Linux server. It keeps just dropping the connection. I was wondering if there was some configuration that I would need to make for this to work. I understand that it is most likely going to be a static configuration since I assume it has to do with the computer not understanding that 5.*.*.* actually refers to another IP:Port. Has anyone had any experience getting this to work?

  Read the article

• Using 1920x1200 mode on SyncMaster T260HD in Linux

  - by dagorym

  I just got a Samsung SyncMaster T260HD monitor. It works straight out of the box with Windows but I can't seem to get it to work with Linux, which is my primary OS for day to day work. The computer boots up but when going into graphical mode on Linux the monitor gives me a "Mode not supported" error and doesn't display anything. I booted up windows and, using PowerStrip, grabbed the exact ModeLine that should be used to get the equivalent setting in Linux and added it to my xorg config file but it doesn't seem to help. the ModeLine is: ModeLine "1920x1200" 153.9 1920 1984 2016 2080 1200 1203 1209 1235 +hsync -vsync This is the modeline for the working display settings in windows but it doesn't seem to work in Linux My complete entry in the xorg.conf file for the monitor is Section "Monitor" Identifier "Monitor0" ModelName "SyncMaster" DisplaySize 518 324 HorizSync 30.0 - 81.0 VertRefresh 56.0 - 75.0 Option "dpms" ModeLine "1920x1200" 153.9 1920 1984 2016 2080 1200 1203 1209 1235 +hsync -vsync EndSection I'm running Scientific Linux 5.4 (clone of Redhat Enterprise Linux 5.4) but I've tried booting with a recent Linux Mint Distro as well as Ubuntu 9.04 and had the same problem. Any suggestions on other things I should try or might be missing? If anyone's gotten this to work I'd love to know. Thanks.

  Read the article

• Why can't I get Apache2 mod_dumpio working under Lucid Lynx Ubuntu?

  - by bland328

  I'm trying to capture all of the traffic to and from an Apache2 web server for troubleshooting purposes, so I did the following to try to set mod_dumpio up properly: Used a2enmod to enable mod_dumpio Changed LogLevel to "debug" in apache2.config Added "DumpIOInput On", "DumpIOOutput On" and "DumpIOLogLevel debug" to apache2.config Issued "/etc/init.d/apache2 restart" to restart Apache Issued "apache2ctl -t -D DUMP_MODULES" to make sure mod_dumpio was loaded I'm watching /var/log/apache2/error.log, but not seeing much there, and certainly not a dump of all input and output. Can anyone help?

  Read the article

• How do you set up Ubuntu to see Windows Network?

  - by Axeman

  I've tried the various tutorials and no success so far. I can connect to the router and from there to the internet, but I cannot see any network shares. I'm connecting through wlan0. I would prefer to keep the dynamic IP address if possible.

  Read the article

• Ubuntu 9.10: how do I troubleshoot a startup script that doesn't appear to run?

  - by TheDeeno

  I've created a bash script 'foo'. I've made that script executable with chmod+x and added it the the start-up by running sudo update-rc.d foo defaults 80 Despite that, it doesn't appear to be working at startup. Is there a way to have my script echo messages to a log? Or is there some log that would record events/errors for this? atm, I feel like I'm flying blind and don't really know how to troubleshoot this.

  Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >