Search Results

Search found 2798 results on 112 pages for 'pull'.

Page 78/112 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >

• Disk doesn't contain a valid partition table

  - by Jeevan Dongre

  I was running a m1.small instance ec2 ubuntu instance. I was running out of disk space, so I upgraded my instance to medium. When I upgraded I actually got 429.5 GB of space and after that I added 10 gb of volume too. When I run the "sudo fdisk -l" command I got this results. Disk /dev/sda1: 8589 MB, 8589934592 bytes 255 heads, 63 sectors/track, 1044 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 429.5 GB, 429461078016 bytes 255 heads, 63 sectors/track, 52212 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda2 doesn't contain a valid partition table Disk /dev/sdf: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 sda1 is the primary parition and sda2 is what I got added upgrading my system to medium. But the problem persists, I am not able to pull the code from git, it is giving me this error. remote: Counting objects: 409, done. remote: Compressing objects: 100% (236/236), done. fatal: write error: No space left on device fatal: index-pack failed

  Read the article

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• Managing Internal Yum Repository Groups

  - by elmt

  What is the best method for handling yum groups dependencies? For example, take this comps.xml file <comps> <group> <id>production</id> <name>Production</name> <default>true</default> <description>Packages required to run</description> <uservisible>true</uservisible> <packagelist> <packagereq type="default">ssh</packagereq> </packagelist> </group> <group> <id>development</id> <name>Development</name> <default>false</default> <description>Packages required to develop</description> <uservisible>true</uservisible> <packagelist> <packagereq type="default">gcc</packagereq> </packagelist> </group> </comps> which is packaged with createrepo -g comps.xml x86_64. The ssh and gcc rpms are not installed in the x86_64 directory. If I run yum groupinstall development, yum is smart enough to pull the gcc package from the RHEL repo even though the groups are defined in my internal repository. However, is this the proper way of doing this, or should I copy the rpms to my local repository and recreate the repo?

  Read the article

• Clustered MSDTC

  - by niel

  Hi I'm setting up a SQL cluster (SQL 2008), Windows 2008 R2. I enable the network access on local dtc and then create a DTC resource in my cluster . the problem is that when i start up the resource it does nto pull through my settings to enable network access. the log shows this: MSDTC started with the following settings: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 0, Trasaction Manager Communication: Allow Inbound Transactions = 0, Allow Outbound Transactions = 0, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 0, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = Mutual Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 where when i restart the local dtc service it says this: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 1, Trasaction Manager Communication: Allow Inbound Transactions = 1, Allow Outbound Transactions = 1, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 1, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = No Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 settings on both nodes in teh cluster is the same. I have reinstalled and restarted to many times to mention. Any ideas ?

  Read the article

• Backing up a Windos 7 partition from Macbook with no OS X

  - by mattcodes

  I have a 3 year macbook with Windows 7 installed as 40gb and OS X as 40gb (80gb HD). I want to remove OS X as Im at the limit of 40gb on Windows and I have not logged on to Mac OS X since installed Win7 (dont flame me). So I want to delete OS X partition and expand my win partition to 80gb BUT I still would like to be able to regularly (once a week/month) backup my Windows 7 partition - its took a while to setup everything up right - not just docs and programs - so when the hard drive dies I want to be able to restore the partition and boot away, (the daily volatile bits I can pull down from dropbox and project from soure control). With Mac OS X I could use Winclone - and this worked flawless last time the HD failed with XP but with the absence of OS X I will need something else. Im thinking can I use a Linux Live boot CD along with an external USB hard drive. Boot from CD and then dd? the partition to the USB? What linux distro live CD should I use? I say dd as if I know what am taking about (I dont) is this the best way to backup a partition (when it will be restored to same hardware as bootable) ? What command?

  Read the article

• Active Directory: Determining DN or OU from log in credentials [closed]

  - by Christopher Broome

  I'm updating a PHP login process to leverage active directory on a Windows server. The logging in process seems pretty straight forward via a "ldap_bind", but I also want to pull some profile information from the AD server (first name, last name, etc...) which seems to require a robust distinguished name (DN). When on the windows server I can grab this via 'dsquery user' on the command prompt, but is there a way to get the same value from just the user's login credentials in PHP? I want to avoid getting a list of hundreds of DNs when on-boarding clients and associating each with one of our users, so any means to programmatically determine this would be preferential. Otherwise, I'll know the domain and host for the request so I can at least set the DC portions of the DN, but the organizational units (OU) seem to be pretty important for querying data. If I can find some of the root level OU values associated with the user I can do a ldap_search and crawl. I browsed through the existing questions and found some similar but nothing that really addressed this, so my apologies if the obvious answer is out there. Thanks for the help.

  Read the article

• Using Truecrypt to secure mySQL database, any pitfalls?

  - by Saul

  The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

  Read the article

• Disable internal display on Macbook Pro without closed lid mode?

  - by jslaker

  I have an early 2007 Macbook Pro running 10.5 that I've recently set up on a KVM with my primary desktop system. The problem I've run into is that I have a 20" 1680x1050 LCD, and OS X only provides options to mirror at the resolution of the built-in display or to span. Since the built-in display runs at 1440x900, this leads to running my LCD at non-native res and a fuzzy picture. There isn't any option that I can find to simply disable the built-in display entirely and run the external LCD at its native resolution. I am aware of closed lid mode, but the MBP was disassembled while in storage for about 6 months (took it apart to pull the HDD) and the cable to the touchpad, which controls the sleep sensor was damaged, meaning closed lid mode won't work. I've looked into replacing the cable, but the cheapest I've been able to find it is $75-100, and I'm trying not to invest any more money into this computer as it also has a completely dead battery and a few other minor problems. I've found the app SwitchResX which appears to allow you to do what I need, but it has a lot of functionality I don't need and a ~$20 registration charge attached to it. An odd set of circumstances, I'm aware, but I was hoping somebody might know of an OS hack that would let me just disable the internal display and be done with it. :)

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]domain.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• Is it possible to create a simple frontend indexer for openbittorent torrents?

  - by SimonK

  I run a website which distributes a few files every now and again, live music performances by a rock band. I create a torrent file, set the trackers as openbittorrent, publicbt and other similar open trackers. I upload the torrent file to my forum, my users download it and the files are shared. No problems there. What I would like to do is index those torrents properly on my website though so I can follow seeders/leechers and other stats online. I know the open torrent trackers don't have an index but I am aware of many, many indexing sites that do that exact thing. I don't know how though. So what I'm asking is what do I need to do to do that myself? I simply want to create a page that lists the torrents I and other users on my site create, the seeders/leechers ratio and a link to the torrent file etc. What data do I need to be able to do that? I'm proficient in general web design but I don't know what I would need data wise to pull the required info on the torrents? Thanks

  Read the article

• REMOTE_USER not getting set?

  - by landed

  I am trying to setup LDAP Authentication in Joomla using a plugin called JMapMyLDAP (in fact 4 plugins each doing a different job). I need to pull a part of a string out of the server variable REMOTE_USER and this should be visible (we see here http://timplummer.com.au/4-how-to-integrate-joomla-3-with-active-directory-using-ldap.html) in phpinfo(); The issue is that REMOTE_USER is not set or at least not appearing. A few things to note (if you don't mind) here- conceptually I am not really understanding authentication as a whole subject it appears to be vast despite my years working in websites. Yes I used asp and built php pages to check a user is who they say they are with a token(/session?) that was given to just them and then they are identified when a stateless request is made to the server. Thats my level of understanding. This sounds different to the basic authentication in apache where a password sits in a file and a username and the user needs to login to a basic form to get access to the folder/docs this is via an .htaccess file. Ok so with the LDAP to work I need to get REMOTE_USER this sounds very reasonable as how else do we know is making the request. Thank you.

  Read the article

• Why does pulling the power cord then pressing the power button fix a non-booting PC?

  - by sidewaysmilk

  I've been working at this institution for about 6 years. One thing thing that I've always found curious is that sometimes—especially after a power outage—we find a PC that won't boot when the power button is pressed. Usually, the fans will spin up, but it won't POST. Our solution is to pull the power cord, press the power button with the computer unplugged, then plug it in and turn it on. It seems more common with Gateway brand PCs than the Dells or HPs that we have around. Does anybody know what pressing the power button does when the computer is unplugged? I have some vague notion that closing the power button circuit allows some capacitors to discharge or something, but I'd like a firmer answer to offer my users when they ask me what I'm doing. My best guess as to why fans can spin but it can't POST is that the BIOS is in some non-functional state. I don't know how BIOS stores state, but my best guess is that there is some residual garbage in its registers or something, like the stack pointer isn't starting at 0 maybe?

  Read the article

• Windows 7 scheduled task returns 0x2

  - by demmith

  I have identical scheduled tasks running in Windows XP Pro and Windows 7. The XP Pro one runs fine, the Windows 7 one always returns 0x2 (which means, "The system cannot find the file specified"; however, executing from the command line is no problem) in the Last Run Result column of the Task Scheduler UI. The scheduled task executes a .bat file daily. The .bat file contains a call to execute a Perl script. As I stated in the previous paragraph, it executes under XP without any trouble but under Windows 7, no dice. The task under Windows 7 is set to "run whether the user is logged on or not." In this case it is me, I am the only user of the system. It is also set to "Run with highest privileges." And it is not hidden. The .bat file executes perfectly well from the command line - it calls the Perl script as expected and the Perl script does its thing. I have searched far and wide looking for an appropriate answer to this issue. So far I have found nothing. What the devil is going on with this Win7 scheduled task? I am ready to pull my hair out.

  Read the article

• Postgresql Data Aggregation over WAN Securely

  - by Zach

  Hey guys, Need some advice on how to proceed with this situation: My current scenario is that I have several postgresql (50+) boxes deployed throughout various locations and data centers and a beefy postgresql box setup at a homebase location. All of the deployed boxes have identical database layouts. I'm looking for a solution that would allow for a few things. I realize some of these options overlap and some might only contain mutually exclusive solutions. However, I'm interested to hear your thoughts :) Remotely query the deployed boxes and pull the results back to the homebase box for processing. Nightly (remote) "sync" or dump the deployed boxes' databases to a master database on the homebase box. Remotely push a table entry to all of the deployed boxes from the homebase box. Ensure security of data in transit, and remotely deployed boxes. Up to this point I've been floating on a homebrew multithreaded python/perl system that SSH's into these boxes remotely, which are ACL'ed off to the homebase server and pulls (or pushes) the raw query results over the ssh connection. I have even touched #2 (remote syncing) as I know that would get nasty really quick. I'm interested in any ideas for a more elegant solution that can scale up and stick to my FreeBSD/Linux environment.

  Read the article

• Server 2008 email on Event variables

  - by Jeff Miles

  One of the new features of Server 2008 is the ability to attach a task to a specific event in the event logs. One of the actions available is to send an email through a SMTP server. This is working great, however it would be ideal if in the message body, the Event contents could be placed. I have tried using $eventdescription and %eventdescription%, but those are just shots in the dark. Any amount of googling produces no results. Does anyone know if this is possible? Update: Sparks' suggestion below is a step in the right direction I believe, however that method doesn't seem to work for all values. For example, I can pull the RecordID, Severity and Channel as shown, but I can't use the same method to retreive the EventID, or most importantly the description. Here's the raw XML from one event: [Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"] [System] [Provider Name="DFSR" /] [EventID Qualifiers="16384"]4412[/EventID] [Level]4[/Level] [Task]0[/Task] [Keywords]0x80000000000000[/Keywords] [TimeCreated SystemTime="2009-05-14T18:18:09.000Z" /] [EventRecordID]45692[/EventRecordID] [Channel]DFS Replication[/Channel] [Computer]servername.domain.com[/Computer] [Security /] [/System] [EventData] [Data]9046C3F4-843E-4A53-B941-4B20764072E5[/Data] [Data]D:\departments\Geomatics\Plan Quality\Data Processing\CG3533017 2009-05-13 KT FIXED[/Data] [Data]D:\departments[/Data] [Data]{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [Data]Departments[/Data] [Data]swg.ca\files\departments[/Data] [Data]B8242CE2-F5EB-47DA-BA5B-1DD2F7EE3AB9[/Data] [Data]DFAA7A54-66CB-4C31-81A0-0F861382C32C[/Data] [Data]CG3533017 2009-05-13-{26D5F604-E603-4F87-8EC3-DE9A945DA8FD}-v927199[/Data] [/EventData] [/Event] I have tried using a ValueQuery for EventData, but it returns no data.

  Read the article

• WINDOWS: Your computer hangs. You can windows + R (run dialog) but performance is so halted taskMGR

  - by John Sullivan

  The question is, what process are available to try to recover from total system instability before pulling the plug when we can do nothing but programs or batches in the path from the run dialog (windows + r key), and performance is so dead that taskMGR / procEXP / other programs with visual guis are not usable? I am not a windows expert, but ideally someone out there has written a program that does more or less stuff like this: Immediately set (or perhaps I can set from the run prompt) its priority to extremely high, evaluate performance bottlenecks. E.g. is CPU 100%? If so identify offending program(s) or problems. Attempt / log fixes, then provide crude feedback asking the user if his performance has stabilized enough to abort, wait a few seconds, if no feedback continue, etc. etc. Eventually try to do any "system cleanup" if the program decides it cannot recover and perhaps finally provide a series of beeps to the user, or what have you, to say "OK, I give up, time to pull the plug". Ideally create a log, when able. These kinds of horrible hangs are a situation where surely trying something, anything, is better than nothing -- as long as that something is intelligent -- when the alternative is ripping out the power coord. Again, I am not a windows expert, so perhaps there is a much more elegant "hands on" approach I am not aware of.

  Read the article

• INACCESSIBLE_BOOT_DEVICE after installing Linux on same drive

  - by kdgregory

  History: My PC was configured with two drives: an 80G on IDE 0 Primary that was running Win2K, and a 320G on IDE 0 Secondary that was running Linux (Ubuntu). I decided to pull the 80Gb drive out of the system, so dd'd the entire 80 G drive (/dev/sda) onto the 320 (/dev/sdb) -- this included the MBR and partition table. Then I pulled the drive, plugged the 320 into IDE 0 Primary, and rebooted. The Windows partition worked at this point. Then I installed Ubuntu into the remaining space on the 320. It works. However, when I try to boot into Windows, I get a BSOD with the following message: *** STOP: 0x0000007B (0x89055030,0xC000014F,0x00000000,0x00000000) INACCESSILE_BOOT_DEVICE Before the BSOD I see the Win2K splash screen, and it claims to be "starting windows" for a couple of seconds -- so it appears that the first stage boot loader is working as expected. Ditto when I try booting in Safe Mode. After reading the Microsoft KB article, I booted into the recovery console and tried running chkdsk /r. It refused to run, claiming that the drive was corrupted (sorry, didn't write down the exact error message). However, I can mount the drive from Linux, and access all files. And for what it's worth, I can scan the drive using the Linux "Disk Utility" (this is Ubuntu, the menus don't show real program names), it claims the drive to be clean. The KB article mentioned that boot.ini could be the problem, so here it is: timeout=10 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows 2000 Professional" /fastdetect Any pointers on what to do next?

  Read the article

• How do I set up Tomcat 7's server.xml to access a network share with an different url?

  - by jneff

  I have Apache Tomcat 7.0 installed on a Windows 2008 R2 Server. Tomcat has access to a share '\server\share' that has a documents folder that I want to access using '/foo/Documents' in my web application. My application is able to access the documents when I set the file path to '//server/share/documents/doc1.doc'. I don't want the file server's path to be exposed on my link to the file in my application. I want to be able to set the path to '/foo/Documents/doc1.doc'. In http://www3.ntu.edu.sg/home/ehchua/programming/howto/Tomcat_More.html under 'Setting the Context Root Directory and Request URL of a Webapp' item number two says that I can rename the path by putting in a context to the server.xml file. So I put <Host name="localhost" appBase="webapps" unpackWARs="true" autoDeploy="true"> <!-- SingleSignOn valve, share authentication between web applications Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Access log processes all example. Documentation at: /docs/config/valve.html Note: The pattern used is equivalent to using pattern="common" --> <Valve className="org.apache.catalina.valves.AccessLogValve" directory="logs" prefix="localhost_access_log." suffix=".txt" pattern="%h %l %u %t &quot;%r&quot; %s %b" /> <Context path="/foo" docBase="//server/share" reloadable="false"></Context> </Host> The context at the bottum was added. Then I tried to pull the file using '/foo/Documents/doc1.doc' and it didn't work. What do I need to do to get it to work correctly? Should I be using an alias instead? Are there other security issues that this may cause?

  Read the article

• Computer won't start up. Stuck on Lenovo splash screen. Help Diagnose

  - by Ace Legend

  I have some (I'm not sure exactly what model) Lenovo 21" IdeaCentre. Honestly, the computer works off and on. I have had problems with it not being able to shutdown, which I fixed. The fan seems to be constantly running, a few other problems as well. Anyway, nobody was using it when all of a sudden it switched to a blue screen. I was in the kitchen, but when I got over to the computer I read the message. It said something about bad drivers, but that is all I saw and then it restarted. However, when it got to the Lenovo Splash screen, nothing happened. I waited there for over 10 minutes, but still nothing. I tried to turn of the computer, but the only way to do it was to pull out the power cable. I then removed all USB devices and tried again. Still nothing. It also won't respond to keyboard input when I try to use enter to interrupt normal startup. My guess is some piece of hardware is damaged inside the machine. However, I have no idea what piece it is. Does anybody have any idea what could be wrong with it? Thanks.

  Read the article

• Why are all of my ZFS snapshot directories empty?

  - by growse

  I'm running an Oracle 11 box as a ZFS storage appliance, and I'm taking regular snapshots of the ZFS filesystems, via cron. In the past, I know that if I wanted to grab a particular file from a snapshot, a read-only copy was kept in .zfs/snapshot/{name}/ and I could just navigate there and pull the file out. This is documented on Oracle's website. However, I went to do this the other day, and noticed that the ZFS directories within the snapshot directories are all empty. zfs list -t snapshot correctly shows the list of snapshots that should be present, and .zfs/snapshots correctly contains a directory for each snapshot, and in each snapshot there is a directory present for each ZFS filesystem. However, these directories appear to be empty. I just tested a restore by touching a file in a little-used share and rolling back to the latest hourly snapshot, and this appears to have worked fine. So the rollback functionality is there. Did Oracle change how snapshots are done? Or is something seriously wrong here?

  Read the article

• screen scraper templates for various websites

  - by intuited

  I'm looking specifically for a convenient way to locally archive posts from this and other similar sites. I'd like to separate the question itself from the answers, or maybe crop the question and store it, keeping the page title. Obviously I don't need to store the menu or the various other site interface chrome. The best way to do this would seem to be to associate an XSLT template with a match on the URL and use that template to pull the various relevant informations and format them. My two-part question: Is there a tool specifically built for this task? I.E. something that takes a URL and checks it against a map of path-matching expressions to templates, and outputs the result of applying the template to that resource? xmlto seems to be most of the way there, and could probably just be called from a script that does the pattern-matching, but something already integrated would be more convenient. Is such a URL_pattern-to-XSLT_template map publicly available somewhere? Question 2.5: Is it legal to do this with sites like this one that have public licenses on their content?

  Read the article

• VPN with VLANs? [closed]

  - by Craig

  As usual, I'm sure I'm in way over my head on this one. My networking skills are limited; so, bear with me if you will. What I have are a few testing servers at my house as well as at a friends house that I want to link together so they can see each other (VPN right? I've done those before). We want to be able to see all the servers and work with them from either location. All the servers also need to be able to see each other. But, we don't want to see each others PCs, printers, PS3s etc. How do we pull that trick off? Multiple VLAN?... subnets?... what? If hardware matters, I have an old PC I was planning on loading pfSense onto because my current el-cheapo router doesn't support VPN. The VPN linking the houses is about the only thing I'm sure on. Beyond that, I'm lost. I'm not a complete noob; but, like I said, I'm not so sharp with the more complex networking. I do however read well... So use lots of descriptive words and feel free to link away to long dry articles if necessary. :-)

  Read the article

• Executing a git command using remote powershell results in a NativeCommmandError

  - by user204777

  I am getting an error while executing a remote PowerShell script. From my local machine I am running a PowerShell script that uses Invoke-Command to cd into a directory on a remote Amazon Windows Server instance, and a subsequent Invoke-Command to execute script that lives on that server instance. The script on the server is trying to git clone a repository from GitHub. I can successfully do things in the server script like "ls" or even "git --version". However git clone, git pull, etc. result in the following error: Cloning into 'MyRepo'... + CategoryInfo : NotSpecified: (Cloning into 'MyRepo'...:String) [], RemoteException + FullyQualifiedErrorId : NativeCommandError This is my first time using PowerShell or a Windows Server. Can anyone provide some direction on this problem. The client script: $s = new-pssession -computername $server -credential $user invoke-command -session $s -scriptblock { cd C:\Repos; ls } invoke-command -session $s -scriptblock { param ($repo, $branch) & '.\clone.ps1' -repository $repo -branch $branch} -ArgumentList $repository, $branch exit-pssession The server script: param([string]$repository = "repository", [string]$branch = "branch") git --version start-process -FilePath git -ArgumentList ("clone", "-b $branch https://github.com/MyGithub/$repository.git") -Wait I've changed the server script to use start process and it is no longer throwing the exception. It creates the new repository directory and the .git directory but doesn't write any of the files from the github repository. This smells like a permissions issue. Once again invoking the script manually (remote desktop into the amazon box and execute it from powershell) works like a charm.

  Read the article

• Windows XP Freezes

  - by Jim Fell

  Hello. I'm running a machine with Windows XP Professional 64-bit. Every so often, it will freeze for no apparent reason. That is, everything stops responding, except the mouse. I can move the mouse around, but I can't click on anything. Keyboard input is also not accepted/received when this problem occurs. The three-finger salute fails to bring up the Task Manager. Even pressing the power button on my computer fails to shut it down. The only way out of this that I have found is to hard-reboot the machine (i.e. pull power or hold power button in for 10 seconds). This problem was occurring on the system when it had all its updates and after a fresh install when not everthing was quite yet updated. I've run the Scandisk utility and the latest version Memtest86 that supports 64-bit architecture; neither found any errors. The last time this happened was on a fresh install of Windows. Only Nero Essentials, Avast antivirus (disabled), Firefox, and Spybot were installed. I was not running Nero, Firefox, or Spybot at the time, and Avast was disabled, so I'm pretty certain this is a Windows issue. Is anybody familiar with this problem or have any pointers? Thanks.

  Read the article

• Lenovo Thinkpad T430 not booting from HDD if there is a USB modem connected

  - by user93353

  I have a T430 Levono Thinkpad running Win7. I use a ZTE USB modem (something like this) for my internet connection. I usually keep the modem plugged into the USB drive even when the laptop is shutdown or hibernating. This worked fine on my earlier laptops. But with the Lenovo, my laptop doesn't boot if the modem is in the USB drive. It shows the initial character based screen where it gives the Thinkpad message & BIOS details and then waits. If I pull out the modem, it goes ahead. I have disabled USB as a boot option in my BIOS settings, but even then this happens sometimes (but not all the times). Likewise while resuming from hibernation. The USB modem also has drivers & ISP connection client which getting installed the first time you use it on any machine. I have used multiple laptops (HP, DELL, Acer, Gateway) but never faced this problem before. I have friends who use other Thinkpad models but haven't faced this issue. Any resolutions, workarounds for this?

  Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >