Search Results

Search found 22986 results on 920 pages for 'array difference'.

Page 788/920 | < Previous Page | 784 785 786 787 788 789 790 791 792 793 794 795  | Next Page >

  • New PC: win7 install issues with 2x3TB in RAID1

    - by goober
    Background / Components Not sure what I've done wrong. Built one PC before successfully in a similar way but this one seems to be struggling. I have the following components: ASUS P8Z68-V/Pro Gen 3 (updated to latest firmware) 16GB (2x8GB) RAM corsair hx850 power supply 2x3TB drives on the intel z68 controller 1x128GB SSD on the Marvel controller sapphire 7950 The problem I set up my 3 TB disks in RAID1 controller appears to recognize them fine during boot as one 2.7TB raid1 volume windows setup sees two disks, both 746 GB, but will only let me install to one and appears to work fine. windows appears to install fine after installer reboots, I receive "windows failed to start" error referencing code 0xc000000e and "\Windows\system32\winload.exe every time I do an install, a new additional "win7" entry is added to the boot menu; all lead to this error. What I've tried: updated the BIOS to the latest firmware attempted to repair the install tried clearing / removing raid / re-raiding drives tried formatting the drives during install attempted to clear the menu Of entries (can't figure out how to do that) No matter how many times I destroy the raid array, format the disks, etc. the boot entries keep piling up. Any idea where I'm going wrong?

    Read the article

  • Mouse Error Code 24. Windows 7

    - by Cj.
    I've had the same mouse for a while, and it's been working fine until one day, it started giving me a message about a device not working properly. I tried updating the drivers, and re-installing, I even deleted old drivers in case my computer should be a little confused. It never made a difference, and my mouse seemed to be working just fine despite getting the permanent error in my device manager, I looked it up several times online, but I never found anything I could actually use, when I go to official websites, I always get the same response "plug in so so into a different place - drivers - install silverlight before you can watch this tutorial, try it on a different machine". so I gave up on that. But now is where I have a real problem, lately, my little strange error evolved into a fullblown Error 24, and my mouse is starting to turn on and off randomely, especially when it is being used, but I do hear it go "badum..dadum" when I'm off doing something else. when I looked up error code 24, I really didn't find much other than it meaning: Code 24 This device is not present, is not working properly, or does not have all its drivers installed. (Code 24) Cause The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed. Devices stay in this state if they have been prepared for removal. After you remove the device, this error disappears. But, I have tried uninstalling the device entirely several times, and it'll go right back to its previous state with error 24, and turning on and off randomely. what do I do? I cannot afford taking it to a repair place, I can't really afford a new mouse either, I refuse to buy cheap ones as I am a gamer, in need of more than 3 buttons, and a good grip is important. Could there possibly be some confusion in the registry? I do remember having gotten some early problems after I converted my vista to windows7. But I hardly dare going in there unless I'm 100% certain of what I'm going for, and I can honestly say I am at a loss here. Edit: it is a USB mouse we're talking about here. MX™518 Optical Gaming Mouse (logitech) Edit2: I am seeing no rupture, so it must be on the inside of my mouse, or inside the rubber, protecting the cable, that would be really inconvenient to search for

    Read the article

  • Why is MySQL unable to open hosts.allow/hosts.deny?

    - by HonoredMule
    I have a storage server running Nexenta (OpenSolaris kernel, Ubuntu userspace) with MySQL on top of a ZFS storage array, using innodb_file_per_table and ulimit -n set to 8K. mysqltuner.pl confirms the file limit and claims there are 169 files. The following command: pfiles `fuser -c / 2>/dev/null indicates one mysqld process having 485 file/device descriptors (and they're almost all for files) so I don't know how reliable the tuning script is, but it is still way less than 8K and this list also finds no other process which is close to it's limit. The global total number of descriptors in use is around 1K. So what can cause mysqld to be constantly streaming the following errors? [date] [host] mysqld[pid]: warning: cannot open /etc/hosts.allow: Too many open files [date] [host] mysqld[pid]: warning: cannot open /etc/hosts.deny: Too many open files Everything appears to actually be operating fine, but the issue is constantly flooding the admin console and starts right away on a fresh boot (not only reproducible, but always from mysqld and always the hosts files, whose permissions are the default -rw-r--r-- 1 root root). I could, of course, suppress it from the admin console but I'd rather get to the bottom of it and still allow mysqld warnings/errors to reach the admin console. EDIT: not only is the actual file descriptor well within sane limits, the issue also persists (with immediate appearance) even with the file limit raised to 65535 and always only on hosts.allow/deny.

    Read the article

  • Recover strategy single bad sector in moricon

    - by Damon
    This week, my harddisk made me an early christmas present in the form of a single defect sector. To make up for the puny size of the present, it chose a sector inside moricons.dll for that. This means that now the system takes about 5 minutes to boot before Windows gives up and moves on, and there's 2 dozen scary "critical failure" entries in the system log after every boot, which is annoying. OK, admittedly, I shouldn't complain, it could be worse, the bad sector could be in ntldr... SMART info more or less indicates (for what SMART can indicate anyway) that the drive is mostly OK. Soft Read Error Rate has a score of 96, and Current Pending Sector Count has a raw value of 8, which translates to a score of 100. Acronis DriveMonitor makes this an issue (lowering the overall rating to 75%), HDD Health calls it "excellent", giving an overall rating of 95% (which is what this harddisk from day one). No single score is below 95 (power on hours and spin up count), and most are 100 anyway. Well, whatever, I've seen drives with perfect SMART values fail from one second to the other, and drives with moderate values work for years. So, I'm inclined not to put too much weight into that overall. TL;DR Now... to the problem: I don't feel like trashing the disk just yet (that's planned with a new OS install upgrading to Win7 early next year, independently of this issue), but in the mean time, I would still like to have a smoothly running system again. Therefore, I feel tempted to tamper with it, but before I render my system entirely unusable (since I've never done this before), I'd like to verify that my planned procedere is likely to suceed in having a working system again: Copy moricons.dl_ from the Windows install disk, rename it to moricons.zip, and unzip it. This gives an intact 5.1.2600.2180 version (the broken one is 5.1.2600.5512 - but I guess this makes not much of a difference, since it's an icon-only DLL, and an outdated copy should work better than one that can't be read) Run chkdsk /r /f` which will "repair" the file (i.e. delete the file without asking, tell the drive to remap the sector, and toss some unreadable junk into a file with a hexadecimal number) Hopefully Windows still boots after this (is that a reasonable expectation, or do I need to have something like BartPE ready? -- but then again, what's that good for in case chkdsk has nuked the entire file system...) Delete the junk file generated by chkdsk, copy the new DLL to %windir%\system32 Reboot. Pray. Maybe I just shouldn't touch anything, since it still kind of works... if annoying, but it works. Unsure... But, is there anything fundamentally wrong with the planned approach? Is this a sensible approach at all?

    Read the article

  • Servers/Websites Keep Going Down

    - by Tyler Johnson
    Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps Type: Linux

    Read the article

  • Nginx settings are screwing up my Drupal form submissions, how do I fix?

    - by bflora
    How do I tell Nginx to "ignore" specific URLS or pages on my web site? I run a Drupal site where anonymous visitors get served via NGINX while logged in users get served via Apache. We do this to keep the load down and scale better. It works great, except, since we set up nginx, a good number of Drupal forms no longer work. For example, before installing Nginx, if you created a new article, then clicked "edit" and edited the article. You could click "save" and your changes to the article would be saved. After setting up nginx, when you make edits and then click "save," the page simple refreshes, but now with "nginx-index.php" inserted into the URL. And your changes to the form were not actually saved to the database. So if you go to edit an article, you'll be on domain.com/node/##/edit or something like that. When you try to save your changes to the form, you'll wind up at domain.com/nginx-index.php?q=node/##/edit. And your changes will not be saved. There is a way around this, but only for administrative users. If you go to a form where this problem is happening, then comment or comment-out three lines in our settings.php file, the form will save properly. Those three lines are: // 'cache_form' = array( // 'engine' = 'db', // ), If they're commented, you uncomment them, them save the form. If they're uncommented, you comment them out and save the form. Obviously, this sucks. My friend who set up our server (and then left the country) told me that there are some Nginx settings that can tell it to "ignore" certain URLs or pages which could work here. How do I do this and where do I do it?

    Read the article

  • Strange monitor issue - screen goes black after a few seconds

    - by Scott Szretter
    My LCD monitor display is going black (turning off). It's a Samsung SYncMaster 2233 widescreen. I am trying to figure out if there is anything I can do about it, or if the monitor is junk. I have tried multiple computers, all have the same issue. I have tried a different vga cable, same issue. Power and video cables are tight / double checked. When I power on the monitor, the blue light turns on at the bottom. Then a second or two later the video comes up as expected and it looks fine. However, about 2-3 seconds after that, the screen goes black. The blue light is still on and solid at the bottom (blue light normally flashes when the monitor is sleeping). If I power cycle the monitor, same thing happens. With no computer connected or when I unplug the vga cable, I see the searching for signal message "digital", then the screen goes black. However it usually shows "digital" then "analog" after that and switches between the two a few times. The buttons on the side do not do anything, although they may be, I just can not see if they are or not. I can usually get the "digital" message by pressing the buttons on the side, but then it quickly goes black again. What is really strange is sometimes I can get it to work fine. I am not sure what the difference is. Last week I connected it up and it worked fine and it stayed fine for at least a week! I did not turn it off or anything, I just let the OS put the display to sleep. Then this week one morning I started having the screen going black issue again. Seems like something is either loose inside or beginning to fail. Do you think there is any hope for it? update: pushing the input select button causes the "digital" and "analog" messages to flash on the screen, but only for a few seconds then it goes black. When it was working properly, those messages would flash back and fourth for probably 10-20 seconds then a message would show saying check input signal, but now just a black screen.

    Read the article

  • Linux Software RAID1: How to boot after (physically) removing /dev/sda? (LVM, mdadm, Grub2)

    - by flight
    A server set up with Debian 6.0/squeeze. During the squeeze installation, I configured the two 500GB SATA disks (/dev/sda and /dev/sdb) as a RAID1 (managed with mdadm). The RAID keeps a 500 GB LVM volume group (vg0). In the volume group, there's a single logical volume (lv0). vg0-lv0 is formatted with extfs3 and mounted as root partition (no dedicated /boot partition). The system boots using GRUB2. In normal use, the systems boots fine. Also, when I tried and removed the second SATA drive (/dev/sdb) after a shutdown, the system came up without problem, and after reconnecting the drive, I was able to --re-add /dev/sdb1 to the RAID array. But: After removing the first SATA drive (/dev/sda), the system won't boot any more! A GRUB welcome message shows up for a second, then the system reboots. I tried to install GRUB2 manually on /dev/sdb ("grub-install /dev/sdb"), but that doesn't help. Appearently squeeze fails to set up GRUB2 to launch from the second disk when the first disk is removed, which seems to be quite an essential feature when running this kind of Software RAID1, isn't it? At the moment, I'm lost whether this is a problem with GRUB2, with LVM or with the RAID setup. Any hints?

    Read the article

  • Slow WLAN file transfer between server and tablet

    - by user266985
    My file server is running Ubuntu 12.04 and I'm sharing files from it over samba. It is connected via gigabit ethernet. My desktop, running Windows 8.1, is also connected via gigabit ethernet. I can transfer files between the two and completely saturate that gigabit pipe. However, I just got a Surface Pro 2, and I'm trying to stream HD movies from my server to the device over WiFi. For some reason, I can't break much past 1.5MB/s transferring files over the network. I've tried streaming through XBMC and a standard file copy; no difference. To add the confusion, if I connect to my guest network and then use my VPN server (installed on the router) to access the file server, I get around 3.2MB/s. I've been running diagnostics to determine the root and I think I've found it but I have no idea what is causing it or how to fix it. Router: Asus RT-N66U Surface Pro 2 Network Card: Marvell Avastar 350N (Driver 19/09/2013 v14.69.24044.150) InSSIDer: Link Score: 100 Co-Channels: 0 Overlapping: 0 5GHz Network Channel: 48+44 iperf File Server as Server; Surface Pro 2 as Client - TCP Performance: Acceptable ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 4] local 192.168.0.90 port 5001 connected with 192.168.0.56 port 57367 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 10.1 MBytes 84.7 Mbits/sec [ 4] 1.0- 2.0 sec 10.4 MBytes 87.6 Mbits/sec [ 4] 2.0- 3.0 sec 10.6 MBytes 88.8 Mbits/sec [ 4] 3.0- 4.0 sec 10.7 MBytes 89.5 Mbits/sec [ 4] 4.0- 5.0 sec 10.1 MBytes 84.4 Mbits/sec [ 4] 5.0- 6.0 sec 10.2 MBytes 85.8 Mbits/sec [ 4] 6.0- 7.0 sec 7.04 MBytes 59.1 Mbits/sec [ 4] 7.0- 8.0 sec 10.8 MBytes 90.2 Mbits/sec [ 4] 8.0- 9.0 sec 10.6 MBytes 89.1 Mbits/sec [ 4] 9.0-10.0 sec 8.62 MBytes 72.3 Mbits/sec [ 4] 0.0-10.0 sec 99.2 MBytes 83.1 Mbits/sec iperf Surface Pro 2 as Server, File Server as Client Performance: Poor ------------------------------------------------------------ Client connecting to 192.168.0.56, TCP port 5001 TCP window size: 22.9 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.0.90 port 40233 connected with 192.168.0.56 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 1.0- 2.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 2.0- 3.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 3.0- 4.0 sec 1.25 MBytes 10.5 Mbits/sec [ 3] 4.0- 5.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 5.0- 6.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 6.0- 7.0 sec 1.38 MBytes 11.5 Mbits/sec [ 3] 7.0- 8.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 8.0- 9.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 9.0-10.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 0.0-10.1 sec 15.0 MBytes 12.4 Mbits/sec For some reason, it gets capped and I haven't got a clue why. Any suggestions? Edit: My link speed is reported as 270Mbps by Windows. I'm less than two metres from the router with a clear line of sight.

    Read the article

  • Merge several mp4 video using ffmpeg and php [on hold]

    - by rihab
    I would like to merge several videos using ffmpeg and php. I want to retrieve the names of the videos dynamically but I can't merge all the videos together I only get i-1 merged videos This is the code I use: <?php $checkBox = $_POST['language']; $output=rand(); function conv($checkBox){ $tab=array(); for($i=0; $i<sizeof($checkBox); $i++) { $intermediate=rand(); $tab[$i]=$intermediate; exec("C:\\ffmpeg\\bin\\ffmpeg -i C:\\wamp\\www\\video_qnb\\model\\input\\$checkBox[$i].mp4 -c copy -bsf:v h264_mp4toannexb -f mpegts C:\\wamp\\www\\video_qnb\\model\\output\\$intermediate.ts"); } return $tab; } $t=conv($checkBox); for($i=0;$i<sizeof($t); $i++) { if($i!=0) { if(sizeof($t)<=2) { exec('C:\\ffmpeg\\bin\\ffmpeg -i "concat:C:\\wamp\\www\\video_qnb\\model\\output\\'.$t[$i-1].'.ts|C:\\wamp\\www\\video_qnb\\model\\output\\'.$t[$i].'.ts" -c copy -bsf:a aac_adtstoasc C:\\wamp\\www\\video_qnb\\model\\output\\'.$output.'.mp4'); } else { exec('C:\\ffmpeg\\bin\\ffmpeg -i "concat:C:\\wamp\\www\\video_qnb\\model\\output\\'.$t[$i-1].'.ts|C:\\wamp\\www\\video_qnb\\model\\output\\'.$t[$i].'.ts" -c copy -bsf:a aac_adtstoasc C:\\wamp\\www\\video_qnb\\model\\output\\'.$output.'.mp4'); exec("C:\\ffmpeg\\bin\\ffmpeg -i C:\\wamp\\www\\video_qnb\\model\\output\\".$output.".mp4 -c copy -bsf:v h264_mp4toannexb -f mpegts C:\\wamp\\www\\video_qnb\\model\\output\\i.ts"); exec('C:\\ffmpeg\\bin\\ffmpeg -i "concat:C:\\wamp\\www\\video_qnb\\model\\output\\i.ts|C:\\wamp\\www\\video_qnb\\model\\output\\'.$t[$i+1].'.ts" -c copy -bsf:a aac_adtstoasc C:\\wamp\\www\\video_qnb\\model\\output\\final.mp4'); $i++; } } } ?> Can anyone help me??

    Read the article

  • .htaccess with godaddy not working in subdomain

    - by explorex
    Hi, i have a site uploaded to shared subdomain (which is inside a folder). and htaccess is not working. please get details from here. EDIT::copied from stack overflow Hi, i uploaded as website to a subdomain, and every page is not working except the front page please check it here. what could be the possible reason? i shoud have 8 pages in front level and many more on admin level but i am getting 404 error as you can see, does anyone has idea or suggestion? UPDATE:: .htaccess file RewriteEngine On RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] RewriteRule ^.*$ index.php [NC,L] UPDATE to url rounting i do have few url router like below BUT i dont have any default router $router->addRoute( 'get-destination', new Zend_Controller_Router_Route('destination/get/:id/:dest-name', array( 'controller' => 'destination', 'action' => 'get', 'id' => 'id', 'dest-name' => 'dest-name' )) ); just to make look cooler and on my navigation (which is loaded from xml i have) something like <nav> <home> <label>HOME</label> <controller>index</controller> <action>index</action> <route>default</route> </home> since i was getting url problem from where url was routed and please check phpinfo at http://websmartus.com/demo/globaltours/public_html/phpinfo.php

    Read the article

  • file read performance degrades as number of files increases

    - by bfallik-bamboom
    We're observing poor file read IO results that we'd like to better understand. We can use fio to write 100 files with a sustained aggregate throughput of ~700MB/s. When we switch the test to read instead of write, the aggregate throughput is only ~55MB/s. The drop seems related to the number of files since the throughput for read and write are comparable for a single file then diverge proportionally as we increase the number of files. The test server has 24 CPU cores, 48GB of memory, and is running CentOS 6.0. The disk hardware is a RAID 6 array with 12 disks and a Dell H800 controller. This device is partitioned with ext4 using the default settings. Increasing the readahead (using blockdev) improves the read throughput significantly but it still doesn't match write speed. For instance, increasing the readahead from 128KB to 1M improved the read throughput to ~145MB/s. Is this a known performance issue in our OS/disk/filesystem configuration? If so, how can we tell? If not, what tools or tests can we use to further isolate the issue? Thanks.

    Read the article

  • Windows 7 not booting after failed SRT (SSD caching) install

    - by david
    This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

    Read the article

  • How to delete removed devices from a mdadm RAID1?

    - by Kabuto
    I had to replace two hard drives in my RAID1. After adding the two new partitions the old ones are still showing up as removed while the new ones are only added as spare. I've had no luck removing the partitions marked as removed. Here's the RAID in question. Note the two devices (0 and 1) with state removed. $ mdadm --detail /dev/md1 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. /dev/md1: Version : 00.90 Creation Time : Thu May 20 12:32:25 2010 Raid Level : raid1 Array Size : 1454645504 (1387.26 GiB 1489.56 GB) Used Dev Size : 1454645504 (1387.26 GiB 1489.56 GB) Raid Devices : 3 Total Devices : 3 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 12 21:30:39 2013 State : clean, degraded Active Devices : 1 Working Devices : 3 Failed Devices : 0 Spare Devices : 2 UUID : 10d7d9be:a8a50b8e:788182fa:2238f1e4 Events : 0.8717546 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 8 34 2 active sync /dev/sdc2 3 8 18 - spare /dev/sdb2 4 8 2 - spare /dev/sda2 How do I get rid of these devices and add the new partitions as active RAID devices? Update I seem to have gotten rid of them. My RAID is resyncing, but the two drives are still marked as spares and are number 3 and 4, which looks wrong. I'll have to wait for the resync to finish. All I did was to fix the metadata error by editing my mdadm.conf and rebooting. I tried rebooting before, but this time it worked for whatever reason. Number Major Minor RaidDevice State 3 8 2 0 spare rebuilding /dev/sda2 4 8 18 1 spare rebuilding /dev/sdb2 2 8 34 2 active sync /dev/sdc2

    Read the article

  • How do I configure IIS to allow access to network resources for PHP scripts?

    - by Dereleased
    I am currently working on a PHP front-end that joins together a series of applications running on separate servers; many of these applications generate files that I need access to, but these files (for various reasons) reside on their parent servers. If I, from the command line, issue a bit of script such as: <?php var_dump(glob("\\\\machine-name\\some\\share\\*")); I will get the full contents of that directory, proving that there's no problem programmatically with PHP reading the contents of a UNC share. However, if I try to execute the same script from the web server, I get an empty array -- more specifically, if I use more explicitly functions designed to "open" a directory like it was a file, I get access errors. I believe this to be a permissions issue, but I am not a server/network administrator type, so I'm not sure what I need to do to correct this and get my script running, and the links I've checked out have not been a terrible amount of help, perhaps due to my background, or lack thereof as far as IIS is concerned, coupled with the fact that we are not actually using .NET for this. Relevant Stats: Windows Server 2008 Standard SP2 IIS 7.0 PHP 5.2.9 I will be connecting to two types of servers: a few other nearly-identical Server 2008 machines, and a machine running embedded XP. Links that have not been particularly helpful but maybe I am just misreading: http://support.microsoft.com/?id=306158 http://support.microsoft.com/kb/207671/EN-US/ http://support.microsoft.com/kb/280383/

    Read the article

  • Nvidia RAID 1 Problem. Degraded drives...

    - by Vedat Kursun
    I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

    Read the article

  • Nvidia RAID 1 Problem. Degraded drives...

    - by Vedat Kursun
    I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

    Read the article

  • Need help troubleshooting highly variable ping times

    - by Elliot.Bradshaw
    I'm at work using Citrix (think Remote Desktop) to connect to client sites. With my job I have to write a fair bit of code while I'm connected remotely via Citrix, so the latency of my internet connection is important. If I'm getting ping times above 250ms, then it becomes almost impossible to scroll, click or type with accuracy. Recently my Comcast business internet has been exhibiting highly variable ping times. If I ping google.com, I'll get pings that range from 9ms all the way up to 1300ms. The problem seems to be at its worst during the hours of 1PM to 4:30PM. Outside of those hours and the variance in pings settles down, mostly between 9ms and 50ms. The signal to noise ratio and upstream power are both fine on my modem--the values are here: http://pastebin.com/D4hWGPXf I ran a trace route from my computer to google.com (the results of which are here: http://pastebin.com/GcdjYvMh) and did another test ping to the IP of the first hop outside of our local network (73.98.44.1)--the variance in ping times existed in exactly the same manner as if I were pinging Google. Connecting directly to the cable modem by CAT5 makes no difference. Here is a screenshot demonstrating the variance of the ping times: http://postimage.org/image/haocdeauv/full/ -- as you can see it can get pretty bad. Three Comcast techs have been out (two of them were here when the problem wasn't happening) and they as well as the regional tier 2 Comcast support were unable to diagnose the problem. I now have a ticket open with tier 3 support, but have yet to hear back from them. Does anyone know what could cause these sorts of problems or have any idea from the traceroute above where it could be originating? The regional tier 2 guy tried to tell me that what I'm seeing is normal--are highly variable ping times like that ever acceptable? Anything I should ask Comcast to do or look at to get this problem fixed? Any tips/advice much appreciated! Edit: This is Comcast cable internet at a small start-up, we've ruled out congestion in our private LAN as a cause (i.e., no one's watching YouTube when the pings become variable). Update: Tier 3 Comcast support advised swapping out the modem, a tech came here today and did that--same problem persists.

    Read the article

  • Expanding raidz vdev

    - by Blubber
    I'm currently planning on installing FreeBSD 9 on my home server. The machine has 4x 1.5TB disks, and at some point, when HDD prices drop I'll be upgrading to something bigger, perhaps 3TB. The disks are connected to an IBM ServerRaid m1015 in IT mode, this card has room for up to eight disks. Now here is the problem, currently the 4x 1.5TB will be connected to the m1015. Then when prices drop I'll be adding something like 4x 3TB, also connected to the m1015. No problem yet, I can just run 2 raidz2 vdevs and put them in the same pool. But, at some point the 1.5TBs will start to break, or I will have to upgrade them when the pool runs out of space. So I started researching if it's possible to expand a raidz vdev, and I found several pages explaining the same procedure, like this on SF: How to upgrade a ZFS RAID-Z array to larger disks on OpenSolaris?. So I went a head and tried that in vmware, I installed FreeBSD 9 and created 6 virtual disks, 3 of 1GB each and 3 of 10GB each. After building a raidz vdev of the 1GBs I replaced them one by one with the 10GB, but the pool did not increase in size. Is this a limitation of the ZFS implementation in FreeBSD? Or am I just doing something wrong?

    Read the article

  • zfs pool error, how to determine which drive failed in the past

    - by Kendrick
    I had been copying data from my pool so that I could rebuild it with a different version so that I could go away from solaris 11 and to one that is portable between freebsd/openindia etc. it was copying at 20mb a sec the other day which is about all my desktop drive can handle writing from the network. suddently lastnight it went down to 1.4mb i ran zpool status today and got this. pool: store state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine if the device needs to be replaced, and clear the errors using 'zpool clear' or replace the device with 'zpool replace'. see: http://www.sun.com/msg/ZFS-8000-9P scan: none requested config: NAME STATE READ WRITE CKSUM store ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c8t3d0p0 ONLINE 0 0 2 c8t4d0p0 ONLINE 0 0 10 c8t2d0p0 ONLINE 0 0 0 it is currently a 3 x1tb drive array. what tools would best be used to determine what the error was and which drive is failing. per the admin doc The second section of the configuration output displays error statistics. These errors are divided into three categories: READ – I/O errors occurred while issuing a read request. WRITE – I/O errors occurred while issuing a write request. CKSUM – Checksum errors. The device returned corrupted data as the result of a read request. it was saying low counts could be any thing from a power flux to a disk event but gave no suggestions as to what tools to check and determine with.

    Read the article

  • Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

    - by Jeff
    A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

    Read the article

  • How to make a redundant desktop system with daily snapshots? (Is btrfs ready for use?)

    - by TestUser16418
    I want to configure a desktop system in which the home filesystem would be redundant (e.g. RAID-1), and would have weekly snapshots taken. I've already done this with ZFS, the snapshot system is wonderful, and with send/recv you can easily create backups on external media. Unfortunately, at that point, I want GNU+Linux and not FreeBSD or Solaris, so I'm looking for suggestions for good alternatives. I reckon that my alternatives are: btrfs - it seems to be exactly what I need, it has snapshots and commands that allow you to easily replicate zfs send. Yet all documentation mentions that it's still experimental. I can't seem to find any actual reports on its reliability or usability issues. Can you point me to any information on that issue that could clarify whether it would be a possible choice? I have a large preference for this option, mostly because I don't want to reformat the drives when btrfs becomes ready, but I there's no information on whether it's usable at all, whether it's a silly idea to use it, etc. The question that I cannot get the answer to is what does "experimental" mean. lvm snapshots and ext4 - preferably not, since it can consume an awful amount of space when new files are created. Creating 200 GB files requres 200 GB free space and 200 GB additionally for snapshots. I also have found it unreliable -- failed metadata rewrite results in an unreadable PV. I'm wondering how btrfs would compare here. A single filesystem (ext4) on a RAID-1 array with custom COW snapshots with hardlinks (like cp -al). That's my current preference if I can't use btrfs. So how experimental btrfs is, which should I choose, and do I have any other options? What if I don't keep external incremental backups, would that affect my choice?

    Read the article

  • Oracle Linux screen freezes during installation

    - by Fearless
    I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

    Read the article

  • Why can't we reach some (but not all) external web service via VPN connection?

    - by Paul Haldane
    At work (UK university) we use a set of Windows servers running WS2008R2 and RRAS which offer VPN service to students in our accommodation. We do this to associate the network connections with individuals. Before they've connected to the VPN all they can talk to is the stuff thats needed to setup the VPN and a local web site with documentation on how to connect. Medium term we'll probably replace this but it's what we're using at the moment. VPN on the 2008 servers allocates client a private (10.x) address. Access to external sites is through NAT on the campus routers (same as any other directly connected client on a private address). Non-VPN connections aren't seeing this problem. Older servers run WS 2003 and ISA2004. That setup works but has become unreliable under load. Big difference there was that we were allocating non-RFC1918 addresses to the clients (so no NAT required). Behaviour we're seeing is that once connected to the VPN, clients can reach local web sites (that is sites on the campus network) but only some external sites. It seems (but this may be chance) that the sites we can reach are Google ones (including YouTube). We certainly have trouble reaching Microsoft's Office 365 service (which is a pain because that's where mail for most of our students is). One odd bit of behaviour is that clients can fetch (using wget on a Windows 7 client) http://www.oracle.com/ (which gets a 301 redirect) but hangs when asked to fetch http://www.oracle.com/index.html (which is what the first URL redirects to). Access works reliably if we configure clients to use our local web proxies (Squid). My gut tells me that this is likely to be something in the chain dropping replies either based on HTTP inspection or the IP address in the reply. However I'm puzzled about why we're seeing this with the VPN clients. Plan for tomorrow (when I'm back in the office) is to setup a web server on external connection so that we can monitor behaviour at both ends of the conversation (hoping that the problem manifests itself with our test server). Any suggestions for things we should be looking at?

    Read the article

  • MySQL performance over a (local) network much slower than I would expect

    - by user15241
    MySQL queries in my production environment are taking much longer than I would expect them too. The site in question is a fairly large Drupal site, with many modules installed. The webserver (Nginx) and database server (mysql) are hosted on separated machines, connected by a 100mbps LAN connection (hosted by Rackspace). I have the exact same site running on my laptop for development. Obviously, on my laptop, the webserver and database server are on the same box. Here are the results of my database query times: Production: Executed 291 queries in 320.33 milliseconds. (homepage) Executed 517 queries in 999.81 milliseconds. (content page) Development: Executed 316 queries in 46.28 milliseconds. (homepage) Executed 586 queries in 79.09 milliseconds. (content page) As can clearly be seen from these results, the time involved with querying the MySQL database is much shorter on my laptop, where the MySQL server is running on the same database as the web server. Why is this?! One factor must be the network latency. On average, a round trip from from the webserver to the database server takes 0.16ms (shown by ping). That must be added to every singe MySQL query. So, taking the content page example above, where there are 517 queries executed. Network latency alone will add 82ms to the total query time. However, that doesn't account for the difference I am seeing (79ms on my laptop vs 999ms on the production boxes). What other factors should I be looking at? I had thought about upgrading the NIC to a gigabit connection, but clearly there is something else involved. I have run the MySQL performance tuning script from http://www.day32.com/MySQL/ and it tells me that my database server is configured well (better than my laptop apparently). The only problem reported is "Of 4394 temp tables, 48% were created on disk". This is true in both environments and in the production environment I have even tried increasing max_heap_table_size and Current tmp_table_size to 1GB, with no change (I think this is because I have some BLOB and TEXT columns).

    Read the article

< Previous Page | 784 785 786 787 788 789 790 791 792 793 794 795  | Next Page >