Search Results

Search found 25727 results on 1030 pages for 'solution'.

Page 795/1030 | < Previous Page | 791 792 793 794 795 796 797 798 799 800 801 802  | Next Page >

• HP/Lenovo alternative to Buffalo iSCSI TerraStation?

  - by Robin Day

  I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/Lenovo? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

  Read the article

• Full-text search locks up database - error 0x8001010e

  - by Stewart May

  Hi We have a full-text catalog that is populated via a job every 15 minutes like so: ALTER FULLTEXT INDEX ON [dbo].[WorkItemLongTexts] START INCREMENTAL POPULATION We have encountered a problem where the database containing this catalog locks up. There are a couple of scenarios, we either see the job execute and the process hang with with a wait type of UNKNOWN TOKEN, or we see another process hang with a wait type of MSSEARCH. Once this happens the job continues to run but informs us that the request to start a full-text index population is ignored because a population is currently active. Looking in the full text log files we see the following error each time these problems occur: 2010-04-21 08:15:00.76 spid21s The full-text catalog health monitor reported a failure for full-text catalog "XXXFullTextCatalog" (5) in database "YYY" (14). Reason code: 0. Error: 0x8001010e(The application called an interface that was marshalled for a different thread.). The system will restart any in-progress population from the previous checkpoint. If this message occurs frequently, consult SQL Server Books Online for troubleshooting assistance. This is an informational message only. No user action is required."'' The only solution is to restart the SQL Server service and then the full text service. This is now occuring on a daily basis now so any help would be appreciated.

  Read the article

• Goal setting/tracking packages for software projects

  - by Avi

  I'm a developer working by myself. I'm looking for a computerized tool to manage my goals and activities. I own it Microsoft Project, but I don't like it. I've started many "projects" but could never keep on using it. Too complex and heavyweight for me. I use MS-Outlook tasks. They are not what I need. No planning capability. Tracking is not nice. I'm using the Pomodoro technique and I like it, but I'm looking for something more comprehensive and with better computerized support. Something that would allow me to define goals with dependencies and time estimation, keep daily prioritized lists etc. So, I'm looking for a solution. One I've found is GoalPro, but I uneasy because I could not find a cross-product "top ten" like review. Are you using any goal setting package such as GoalPro? Which? Does it help? Pros and Cons?

  Read the article

• Problem with Strange VMWare behaviour when shutting down guest.

  - by adza77

  Hi, I've been having a problem for a while now with VMWare Workstaion. (Originally with 6.5, but now with 7.0 and 7.0.1 too). The problem occurs when I choose to shut down a guest. VMWare itself seems to hang. If I choose to shut down a guest that's opened full screen, and during the process I minimise the screen to work on other applications in the host, often (not all the time) when I return to the guest I have a 'greyed out' screen and the system becomes unresponsive. The host O/S still seems to be working, but I am unable to switch to other applications. (I can bring up the taskbar on the host and 'see' other applications and even switch to them, but VMWare still stays 'on top' being unresponsive). I can not terminate VMWare even when windows says that the application has become unresponsive and gives me the option to terminate. VMWare stays on top, and I'm forced to either shutdown, or log off and log back on in order to regain control of my computer. This happens with both Windows 7 and Windows Vista guest operating systems (32 bit), and I have had it happen on multiple host machines, and multiple guest machines too. Current Host: Windows 7 64 bit, 8GB Ram, 500GB HDD, i7 Processor. I have been searching for more than 6 months for a solution but have found none, so finally decided to post here. Does anyone know what might be causing the problem (+or even how to minimize the VM so I can at least access any other applications and save work before forcing a logoff / reboot+) would be extrememly handly. If I know the correct keystrokes to save and close in an application on the host I can do this by task-switching to the desired app to save and close successfully, but I can't see what I'm doing because VMWare Workstation is still on-top 'greyed' out. Cheers Adam.

  Read the article

• Problem with Strange VMWare behaviour when shutting down guest.

  - by adza77

  Hi, I've been having a problem for a while now with VMWare Workstaion. (Originally with 6.5, but now with 7.0 and 7.0.1 too). The problem occurs when I choose to shut down a guest. VMWare itself seems to hang. If I choose to shut down a guest that's opened full screen, and during the process I minimise the screen to work on other applications in the host, often (not all the time) when I return to the guest I have a 'greyed out' screen and the system becomes unresponsive. The host O/S still seems to be working, but I am unable to switch to other applications. (I can bring up the taskbar on the host and 'see' other applications and even switch to them, but VMWare still stays 'on top' being unresponsive). I can not terminate VMWare even when windows says that the application has become unresponsive and gives me the option to terminate. VMWare stays on top, and I'm forced to either shutdown, or log off and log back on in order to regain control of my computer. This happens with both Windows 7 and Windows Vista guest operating systems (32 bit), and I have had it happen on multiple host machines, and multiple guest machines too. Current Host: Windows 7 64 bit, 8GB Ram, 500GB HDD, i7 Processor. I have been searching for more than 6 months for a solution but have found none, so finally decided to post here. Does anyone know what might be causing the problem (+or even how to minimize the VM so I can at least access any other applications and save work before forcing a logoff / reboot+) would be extrememly handly. If I know the correct keystrokes to save and close in an application on the host I can do this by task-switching to the desired app to save and close successfully, but I can't see what I'm doing because VMWare Workstation is still on-top 'greyed' out. Cheers Adam.

  Read the article

• Stepmania + KDE4 = sound problem

  - by picca

  I cannot manage to get KDE4 + stepmania working. If I run StepMania I always get: StepMania 3.9 Log starting 2010-12-24 14:52:48 Loading window: gtk OS: Linux ver 020636 Crash backtrace component: x86 custom backtrace Crash lookup component: dladdr Crash demangle component: cxa_demangle Runtime library: glibc 2.11.2 Threads library: NPTL 2.11.2 TLS is available ALSA: Advanced Linux Sound Architecture Driver Version 1.0.23. ALSA Driver: 0: HDA ATI SB [SB], device 0: STAC92xx Analog [STAC92xx Analog], 0/1 subdevices avail ALSA Driver: 0: HDA ATI SB [SB], device 1: STAC92xx Digital [STAC92xx Digital], 1/1 subdevices avail Couldn't load driver ALSA: dsnd_pcm_open(hw:0): Device or resource busy Mixing 0.000000 ahead in 0 Mix() calls Couldn't load driver ALSA-sw: dsnd_pcm_open(hw:0): Device or resource busy Mixing 0.000000 ahead in 0 Mix() calls Couldn't load driver OSS: RageSound_OSS: Couldn't open /dev/dsp: Device or resource busy Language: english Theme: default Error: Couldn't find a sound driver that works I found that in StepMania/Data/StepMania.ini I should add following line: SoundDevice=default That enables me to run StepMania, but I don't have any sound. Which is pretty bad for an application like this one. I'm quite sure that the problem is in phonon that is blocking the audio device to which StepMania needs to access directly. I think that I can fix this if I run other (lighter) window-manager than KDE4. But that is not a solution occasional linux user. Do I have any chance to get StepMania under KDE4 completely working?

  Read the article

• "Network is unreachable" When pinging google, can connect to internal computers on debian VM

  - by musher

  Similar to this SU question: "Network is unreachable" when attempting to ping google, but internal addresses work Actually, it's pretty much the same base issue. I went through that thread trying to find a solution, I changed my resolv.conf: before: domain [my work domain] search [my work domain] nameserver [my gateway] nameserver [my gateway2] I changed it to: after: domain [my work domain] search [my work domain] nameserver 8.8.8.8 nameserver 8.8.4.4 However, any time I reboot the computer the resolv.conf gets overwritten to the previous version (the 'before' above). The issues began after I installed virtualbox additions, X server and (specifically) LXDE: Cat of apt history.log: Start-Date: 2014-08-21 10:03:42 Commandline: apt-get install virtualbox-guest-utils virtualbox-guest-dkms Install: x11-xkb-utils:amd64 (7.7+1, automatic), libxaw7:amd64 (1.0.12-2, automatic), xfonts-utils:$ End-Date: 2014-08-21 10:03:56 Start-Date: 2014-08-21 10:18:39 Commandline: apt-get install lxde Install: desktop-base:amd64 (7.0.3, automatic), libgoa-1.0-0b:amd64 (3.12.4-1, automatic), lxmenu-d$ End-Date: 2014-08-21 10:21:52 Start-Date: 2014-08-21 10:26:40 Commandline: apt-get upgrade Upgrade: libio-socket-ssl-perl:am ifconfig on the guest: root@Peridot:~# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:89:c9:20 og inet addr:172.31.2.102 Bcast:172.31.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe89:c920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2281 errors:0 dropped:1 overruns:0 frame:0 TX packets:463 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:266507 (260.2 KiB) TX bytes:120554 (117.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) The adapter in VBox is a bridged adapter directly onto my ethernet connection; as are my other 2 VMs (which work) Other SU questions I've tried: "connect: Network is unreachable" in VirtualBox VM

  Read the article

• Imac g5 with no OS nor CD drive

  - by sinekonata

  What I want: Ubuntu on a g5 Imac. What I have: An empty PC (Intel g5 17" Imac) with broken CD drive. Its model is A1173. This PC with Ubuntu 12.04 and an old Vista partition. a usb flash drive. Problems: No CD means the only boot Drive I could use is USB. There are no BIOS on Macs so I can't set boot settings or even see if it detects my USB drive. When I start the machine and press ALT the first and only thing I see is an old corrupted winXP partition and not a single option or additional information. So assuming blindly that the Mac hardware/firmware works normally, I don't have any Mac OS to use any of the tools that I found on different tutorials for building a bootable .img drive for macs. I can't find much software on Linux/Windows to substitute to those tools, for example among others converting an .iso file (win/linux) to .img (mac I guess). Which makes me think that the scenario where someone like me has Mac hardware but no Mac OS is extremely rare. So other than finding someone that has a Mac I have no solution. So I ask what would you do? the only thing is it should not involve any money (I know mac soft is rarely free) which also excludes getting any MacOS unless I can use a free macos.img for VM or restore the original Mac for free. Thank you

  Read the article

• How do you backup your own files? [on hold]

  - by Antonis Christofides

  I'm a system administrator and I use rsnapshot to backup some servers, duplicity for some others. Both work fine, each one with advantages and disadvantages. Despite that, I am at a loss on how to backup my own private files. I'd use duplicity to automatically backup my files to a remote server; but the problem is that once in a while I must do a full backup. My emails and important files are 9G, and I expect this to increase. Uploading through aDSL at 1Mbit would be 20 hours. Too much. rsnapshot doesn't require periodic full backups (only the first time), but it must be running on the remote server and have a means to connect to my computer; if the server is compromised (or simply if the NSA decides to use it), my own machine is also compromised. Not good. The only solution I've come up with is use encfs, use unison to synchronize the files to a remote server, and use duplicity or rsnapshot on the remote server to backup these files. In that case, the question is whether I can sync the files on many computers; is it possible for encfs to be used with the same key on many computers? I also think that if I append one character to the unencrypted file, its encrypted encfs counterpart might change a lot, so that incrementals with duplicity would be less efficient—but not a big deal. Maybe also, when I need to restore a file, finding the correct file to restore could be a pain, because of filename encryption. I wonder whether there is any other possibility that I've overlooked. Maybe I'm asking too much for my personal use, and I should settle with an external disk?

  Read the article

• HAProxy crashes on all requests in 1.5-dev12

  - by Daniel Hough

  I'm having an issue where HAProxy is crashing with no explanation when I switch from 1.4.12 to 1.5-dev12. The reason I'm switching is for the SSL offloading. My config file doesn't have any errors, it's quite simple and it works well with 1.4 - but for some reason when I run it with 1.5-dev12 I see the logs noting that the two backends I have have been set up, and then when I hit one of the frontends, I get an HTTP 400 in the browser and suddenly HAProxy isn't running anymore when I check. I understand that a common workaround to the lack of SSL support for HAProxy is to use Stud, and I may go with that since I am in need of an SSL solution for my service, but before I dele into that world I thought I might see if anybody has experienced the same problems and might know how to fix it. The server is Ubuntu 10.04 and I followed the make instructions on the Exceliance blog here. EDIT: On the advice of Kyle Brandt, I did a bit more investigation. I attached gdb to the haproxy process and when the crash occurred this is what I got: Program received signal SIGSEGV, Segmentation fault. 0x0804e5c2 in dequeue_all_listeners (list=0x9e1a418) at src/protocols.c:184 184 list_for_each_entry_safe(listener, l_back, list, wait_queue) { P.S. HAProxy is awesome, so thank you Exceliance for providing us with something so useful :)

  Read the article

• Apache suddenly very slow on http and faster on https

  - by hsnm

  Background: I have Apache 2 running on ubuntu. There is a low usage on it and mostly being accessed for a web service URL from mobile apps. It was working fine until I installed SSL certificates. I now have both http and https. When I access the server using https, I get a fairly quick response (but probably not as fast as before). When I use http, it's so slow. What I tried: From this post: I curl localhost from the host and it takes some time, meaning there is no routing issue. The server runs on Amazon EC2 instance and is managed by me only. Also: I see that Apache once running, creates the maximum number of processes it is allowed to, which was not the case before. I lowered the MaxClients to 20 and I think I'm getting faster responses but it still takes over a minute and I always have MaxClients Apache processes. dmesg returns many [ 1953.655703] TCP: Possible SYN flooding on port 80. Sending cookies. When I netstat I get many entries with SYN_RECV. Possibly a DDoS attack? From EC2's monitoring diagrams I see a pattern of high "Maximum Network In (Bytes)" since 2 days ago. By the way the server is still being tested, the actual traffic is very low and not consistent. I tried to go with this solution to limit incoming connections using iptables, still no luck, but I'm trying. Question: What could be the problem? Is this a DDoS attack?

  Read the article

• Losing internet connection after few minutes (5-10 maybe)

  - by Korchkidu

  I took a computer that was not updated for months. Internet was working just fine so basically, I updated zonealarm, avast and installed all windows updates and especially SP3. After that, when I reboot, Internet works fine but after few minutes, Firefox says that the connection was reset. IE does not work either. However, my connection is still up and running as I can make a ping on www.google.com for example. Here are the solutions I tried with no success so far: 1) Uninstalling SP3; 2) Uninstalling IE8 and IE7; 3) Manually setting DNS and IPs; 4) Removed proxy settings from Firefox and IE; 5) Restarting DNS and DHCP related services; 6) Reset TCP/IP with netsh int ip reset c:\resetlog.txt; 7) Updated my ehternet card driver; 8) Restarted, tweaked all the connections in any directions and any configuration possible I believe; 9) Disabled Zone Alarm and Avast; Also, update kb981793 always fails on install. Please, help me as I spent two days already on this and I cannot find any solution. If I cannot fix this problem tomorrow, I will have to format-reinstall everything. Thanks for any help. Regards.

  Read the article

• DNS resolve .com domain on local domain

  - by Joost Verdaasdonk

  I'm building a local 2008 R2 domain as a test case to be able to write a roadmap for the real new domain that needs to be created soon. What I would like to know if I'm able to make a record in DNS that will point the domain name: www.example.com and example.com to one of the servers in my network. I tried creating an a-record for it but that doesn't work. To be honest I'm not even sure if this is possible? So can I do this? That way I would be able to fully test all our services (and webb app) offline before I build the real domain and switch the DNS records at the provider. Some advice if possible and where to start is appreciated. The solution (Thanks Brent): Create new Forward lookup zone pointing to example.com Create empty A record pointing to IP of the webserver you are targeting If www is needed create A record with Name: www and IP of your webserver sub domains repeat the process but then with names for example: sub or www.sub (and ip your webserver) Be aware of the DNS Cache while you are in this process. Things can take time or do the following: Right click the server and choose clear cache in CMD: ipconfig /flushdns (to flush the client cache)

  Read the article

• Setting umask for all users

  - by Yarin

  I'm trying to set the default umask to 002 for all users including root on my CentOS box. According to this and other answers, this can be achieved by editing /etc/profile. However the comments at the top of that file say: It's NOT a good idea to change this file unless you know what you are doing. It's much better to create a custom.sh shell script in /etc/profile.d/ to make custom changes to your environment, as this will prevent the need for merging in future updates. So I went ahead and created the following file: /etc/profile.d/myapp.sh with the single line: umask 002 Now, when I create a file logged in as root, the file is born with 664 permissions, the way I had hoped. But files created by my Apache wsgi application, or files created with sudo, still default to 644 permissions... $ touch newfile (as root): Result = 664 (Works) $ sudo touch newfile: Result = 644 (Doesn't work) Files created by Apache wsgi app: Result = 644 (Doesn't work) Files created by Python's RotatingFileHandler: Result = 644 (Doesn't work) Why is this happening, and how can I ensure 664 file permissions system wide, no matter what creates the file? UPDATE: I ended up finding a cleaner solution to this on a per-directory basis using ACLs, which I describe here.

  Read the article

• SQL Server 2005 to 2008 DB attach elp please!

  - by Brandon

  I have SQL Server 2005 Standard on my personal machine. I created a very big DB about 21 gb. I made a backup and transferred the .bak file via an ftp program to my dedicated server. I have SQL Server 2008 Enterprise Edition on my dedicated server. I tried restore the transferred .bak file but got an error. I posted the error on here and was told the database is corrupt. How? I don't know. The connection was not interrupted during the ftp transfer. The DB works on my own machine. So then I detached the db on my own machine and transferred the mdf and ldf file to my dedicated server through ftp again and again there were not interruptions. Now I try to attach the db and get this error: The header for file 'DB.mdf' is not a valid database file header. The FILE SIZE property is incorrect. (Microsoft SQL Server, Error: 5172) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&ProdVer=10.00.1442&EvtSrc=MSSQLServer&EvtID=5172&LinkId=20476 I already wasted 21 gb transferring the .bak file. Now I used another 21 to transfer mdf and additional ldf file. Please tell me there's a solution. The db can detach and attach fine on my machine in sql server 2005 but not SQL server 2008 on my server.

  Read the article

• unable to set xmx beyond 4gb on system having 8gb RAM

  - by Arun

  I need to set ANT_OPTS=-Xms1024m -Xmx6144m -XX:PermSize=1024m -XX:MaxPermSize=1024m JAVA_OPTS=-Xms1024m -Xmx6144m -XX:PermSize=1024m -XX:MaxPermSize=1024m I have a system with 8gb(recently upgraded from 4 gb) But once i set the ant opts to above said value I am not able to run any of my ant targets and I get the following error [ERROR] Argument error: -Xmx6144m [ERROR] Specified maximum heap size (6144 MB) is larger than the address space on this platform (4 GB). [WARN ] -XX:PermSize=1024m is not a valid VM option. Ignoring [WARN ] -XX:MaxPermSize=1024m is not a valid VM option. Ignoring Could not create the Java virtual machine. This indicates the Java that I have on my system java version "1.6.0_20" Java(TM) SE Runtime Environment (build 1.6.0_20-b02) Oracle JRockit(R) (build R28.1.0-123-138454-1.6.0_20-20101014-1351-windows-x86_64, compiled mode) and I am running a Windows 7 on Intel Core 2 duo 3Ghz processor and 8gb RAM Any pointers in solving this issue would be of great help. PS: I did google for the error and it was one of my 1st such occurence where I didnot get any links pointing to the specific solution. Maybe no one has encountered such a scenario

  Read the article

• IPv6 works only after ping to routing box

  - by Ficik

  Situation: There is ipv4 only router in network and every computer is connected to it (wifi or cable). Server with ipv4 and ipv6 is connected to this router as well. Server has configured tunnelbrokers 6to4 tunnel and radvd. Clients in network has right prefix and can ping each other. But they can't ping to internet until they ping Server (the one with tunnel). I found somewhere that it's icmp problem, but I couldn't find solution. Is it problem that there is ipv4 only router? server and client runs linux router runs dd-wrt without ipv6 support :( Ping try: standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes ^C --- ipv6.google.com ping statistics --- 29 packets transmitted, 0 received, 100% packet loss, time 28223ms standa@standa-laptop:~$ ping6 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 PING 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478(2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478) 56 data bytes 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=1 ttl=64 time=3.55 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=2 ttl=64 time=0.311 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=3 ttl=64 time=0.269 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=4 ttl=64 time=0.292 ms ^C --- 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3000ms rtt min/avg/max/mdev = 0.269/1.107/3.559/1.415 ms standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes 64 bytes from 2a00:1450:8007::69: icmp_seq=1 ttl=57 time=20.7 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=2 ttl=57 time=20.2 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=3 ttl=57 time=23.4 ms ^C --- ipv6.google.com ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2001ms rtt min/avg/max/mdev = 20.267/21.479/23.413/1.392 ms

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• Windows network routing

  - by fabianvilers

  Hi! I'm working by my customer premises and they let me connect my private laptop on a dedicated Wi-Fi for internet access. It's nice for external consultants. The only issue is that we can't connect on a remote server on port 25. I suppose this policy is set up to avoid infected computers sending spam from their network. As you can have guessed, this is something weird that I can't send mail at all. Fortunately, I've a 3G cell phone that I can connect by Bluetooth on my laptop. So when I want to send an e-mail, I have to disconnect from Wi-Fi, connect my phone, send the e-mail, disconnect phone and reconnect Wi-Fi. Kinda overhead. My question is: how can I tell Windows 7 to use the Wi-Fi for every out connection, but if it's a connection on port 25, use the cell phone network? With this solution, I could let my phone connected all day without having to switch again and again. Thanks a lot for your anwwers. Fabian

  Read the article

• Provider claiming "all web servers in the cloud are automatically kept in sync" - should I be skeptical?

  - by RobMasters

  I'm no expert in cloud computing - I've spent a fair bit of time researching it and various providers but am yet to get any hands-on experience with it. From what I've read about AWS and auto-scaling EC2 instances though, it seems as though each instance should be completely decoupled from all other instances. i.e. If content is uploaded to the web server's local filesystem from a custom CMS backend then that content won't be available if subsequently requested from a different web server in the auto-scaling group. Is that right? I met with a representative of our existing hosting provider recently and he was claiming that it isn't a problem that our legacy CMS system is highly dependent on having a local filesystem. He said that all web servers, regardless of how many, would be kept as exact duplicates so I shouldn't notice any difference compared to our existing setup of a single dedicated server. This smells a little too much like bull fecal-matter to me...should I be skeptical about this? I'm a little worried because my (non-technical) boss who ultimately makes the decisions is all for signing up to this cloud solution because it won't require any extra work. I'm sure that they must at least be able to provide this, otherwise they wouldn't be attempting to sell it to us. But at what cost? It sounds as though each web server will always need to be checking the other web server(s) for new static content, which to me sounds like unwanted overhead that'll slow things down. I'd really appreciate it if somebody could clear this up to me. I'm all for switching to AWS and using S3+CloudFront for all static content, but that isn't looking very likely to happen at the moment.

  Read the article

• MS Word custom dictionary making spellcheck slow - ideas?

  - by ezuk

  I have a user who edits technical materials. She uses MS Word's Custom Dictionary all the time for spelling; it has grown very large, and is now making spell check very slow. All of the advice I've read online says to disable the custom dictionary. This is an easy solution, but is not workable for the user, because she actually needs this dictionary. So, is there any way to optimize the custom dictionary and/or Word itself, so that a large dictionary file doesn't slow things down quite so badly? Many thanks. Update after suggestions: I ran contig on the file, and it reports just 1 frag, so that's not the issue I think. The file is 9.95KB -- 1,117 lines, each consisting of just a single word. I viewed the file using Notepad and none of the lines seems corrupted, strange, or overly long (no line seems to be over 10 chars or so). Both of your suggestions were helpful so I will upvote both; any further tips would be most welcome.

  Read the article

• Windows 7 Taskbar resets on every login

  - by Arne Mertz

  I like to reorder my Taskbar a bit, other than the Windows 7 default is. I use two "rows", the lower is for quicklaunch and other toolbars: This works perfectly, as long as I don't log off from the computer. Every time I log in, Windows 7 has messed up/reset the toolbar positions like this: So I have to drag them into position again and again, every morning. Fixing the taskbar positions won't help, I tried to google for the problem but it does not seem to be very common. Does anyone recognize that problem and has a solution? Update: This is not the AutoLogon bug. AutoLogon is off. We have installed Novell at our company, and it does not matter wether I log directly onto the Novell network or only to the computer first and to Novell later. Update2: I get the same issue when I logon without Novell, i.e. when I log on only to the computer. When I boot in safe mode, the taskbar looks essentially the same: Update3: KB979155 says it's "not applicable to my system". Creating a neew user is not an option since I don't have the admin privileges to do that - I have almost any other local admin privileges, though.

  Read the article

• Create custom launchers in GNOME 3

  - by hochl

  I'm using Debian testing, and I have been switched to GNOME 3 by the Debian update yesterday. I'm not very comfortable with the UI. I wanted to customize everything like I had it with GNOME 2, but I simply couldn't find any way to change preferences like I'm used to. I've digged some, but all answers I could find did not help me achieve my goals. So please, if anyone knows the solution to this I'd be thankful: 1) I want several launchers that launch terminals, with different arguments and different coloring/title. I have searched everything and there seems to be no menu, no right-click, nothing which is standard in any UI I know. How can I create several launchers in this bar on the left side that launch the same application, just with different parameters? With GNOME 2 this was a piece of cake. 2) I want to switch between different terminals using ALT-TAB. Right now, I'm always just getting to the same, already-opened terminal. When I open two terminals by simply creating the second one by issuing xterm &, I still get one Terminal entry with ALT-TAB, and I have to navigate with cursor keys or mouse wheel to select one of the two xterminals. Instead, I want to open a new terminal when I click the quick launch terminal icon from the bar on the left side of the screen and navigate through them like on KDE/GNOME 2/Windows/any reasonable UI. Can this be done? 3) Is there a trick to make bluetooth devices work like on GNOME 2? Right now, my BT keyboard won't pair anymore, which, as you can imagine, makes me pretty angry. and, if anything fails: 4) How can I switch back to GNOME 2 again? :-) Honestly, who did design this? What were they smoking? I feel like I'm not allowed to do anything except start one of any application that has an icon and just with the default parameters. That can't be true, right? I feel massively restrained by this stuff :(

  Read the article

• Redirection of outbound UDP port.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. I tried, but can't seem to get iptables to do what I want. I'm not sure if it's my lack of skill, or if I'm trying the wrong solution. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• How do I repartition an SDHC card in Windows?

  - by Peter Mortensen

  How do I repartition an SDHC card (4 GB or more)? Do I need third-part tools or Linux (a live CD solution would be OK)? In Windows' Disk Management the option Delete Partition is dimmed out: I can reformat the card as FAT32, copy files to and from the card and even change the file system to NTFS using the command line command CONVERT, but not repartition it. The article How to Partition an SD Card in Windows XP talks about using "a Windows enabler program" which sound rather dubious to me. I have tried to change from “Optimize for quick removal” to “Optimize for performance”. The option to format as NTFS appeared, but the Delete Partition option is still dimmed out. Platform: Windows XP 64-bit SD card reader: USB 2.0 device, LogiLink® CR0005C Cardreader 3,5' USB 2.0 intern 54-in-1 mit USB Front Kingston 16 GB SDHC card, speed class 4. (It could be formatted as FAT32 and successfully used in a 4 GB ReadyBoost setup (Windows 7).) I have also tried on different versions of Windows and with different cards with the same result: Kingston 4 GB SDHC card, speed class 4 (the one shown in the screenshot) Transcend 2 GB (not marked as SDHC, but SD) Windows 7 32-bit (albeit with a somewhat an older card reader) and Windows XP 32-bit on an EliteBook 8730w

  Read the article

< Previous Page | 791 792 793 794 795 796 797 798 799 800 801 802  | Next Page >