Search Results

Search found 1275 results on 51 pages for 'nat weiss'.

Page 8/51 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

  • pix 501, static route to d-link router (different subnet)

    - by ra170
    I have pix 501 cisco firewall with internal ip 192.168.10.1. I have connected d-link router (dir-655) to pix 501. The d-link router has internal ip 192.168.0.1 The picture would like something like that: |pix 501| has 192.168.10.1 ip |DIR-655| has 192.168.0.1 ip 1. |cable modem|----|pix 501|-------|DIR-655|-----PC 2. PC--------|pix 501|---------|DIR-655| | | |cable modem| When I'm on the wireless network (dir-655) with assigned ip of 192.168.0.x I can cross the subnet and connect to my firewall 192.168.10.1. (pic. 1) The problem is that if I'm on the 192.168.10.x network I can't connect to anything over at 192.168.0.x network. (pic.2) I've tried entering a static route like this: `route inside 192.168.0.0 255.255.255.0 192.168.10.1 1` I also tried assigning static ip to wan interface on DIR-655 to 192.168.10.30 and then tried this: route inside 192.168.0.0 255.255.255.0 192.168.10.30 1 But still, can't connect to 192.168.0.1 or anything on that subnet. Is there a way to setup a static route? Would adding a separate router between PIX 501 and DIR-655 help? I would think that static route like this should take care of it, but it doesn't. This is my route config and nat: (config)# sh route outside 0.0.0.0 0.0.0.0 (outside_IP) 1 DHCP static outside (outside_IP) 255.255.248.0 (outside_IP) 1 CONNECT static inside 192.168.0.0 255.255.255.0 192.168.10.1 1 OTHER static inside 192.168.10.0 255.255.255.0 192.168.10.1 1 CONNECT static or (route inside 192.168.0.0 255.255.255.0 192.168.10.30 1) (config)# sh nat nat (inside) 1 192.168.1.0 255.255.255.0 0 0 nat (inside) 1 192.168.10.0 255.255.255.0 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 I ended up turning DIR-655 into an Access Point (turning off DHCP and pluging cable from PIX lan interface into one of the LAN interfaces on DIR-655, and leaving WAN port empty), that works as far as DIR-655 being on the same subnet now, and I can access every machine. However the question is, why can't I simply route between those two? would router between these two help? One of the reasons is, that the PIX 501 has only 10 licences, so now I'm using almost all of them. (I have few computers, iphones, ps3, print server, etc.) I would really appreciate some help! Thanks.

    Read the article

  • DrayTek 2820 configuration using public IP addresses

    - by Kev
    I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

    Read the article

  • Running multiple services on different servers with IPv6 and a FQDN

    - by Mark Henderson
    One of the things NAT has permitted us to do in the past decade is split physical services onto different servers whilst hiding behind a single interface. For example, I have example.com behind a NAT on 192.0.2.10. I port-forward :80 and :443 to my web server. I'm also port forward :25 to my mail server, and :3389 to a terminal server and :8080 to the web interface of my computer that downloads torrents, and the story goes on. So I have 5 port forwardings going to 4 different computers on example.com. Then, I go and get me some neat IPv6. I assign example.com an IPv6 address of 2001:db8:88:200::10. That's great for my websites, but I want to go to example.com:8080 to get to my torrents, or example:3389 to log on to my terminal server. How can I do this with IPv6, as there is no NAT. Sure, I could create a bunch of new DNS entries for each new service, but then I have to update all my clients who are used to just typing example.com to get to either the website or the terminal server. My users are dumber than two bricks so they won't remember to connect to rdp.example.com. What options do I have for keeping NAT-style functionality with IPv6? In case you haven't figured it out, the above scenario is not a real scenario for me, or perhaps anyone yet, but it's bound to happen eventually. You know, with devops and all.

    Read the article

  • Cannot Ping a server after configuring the Routing and Remote Access Services

    - by stacker
    After configuring the Routing and Remote Access Services to be a both VPN and NAT service, I cannot ping that server anymore from the external side. But when I configure it to be just a VPN server, or just a NAT server, I do able to ping it from the external side. My configuration is like: DC: 192.168.20.11 VPN and NUT: Nic 1: 192.168.20.1, NIC 2: 192.168.147.171 Client: 192.168.147.1 The mask is always: 255.255.255.0 I cannot understand why when configuring the VPN server to be a VPN and NAT, I cannot ping the server anymore.

    Read the article

  • Bridging wireless and wired networks on Linux box

    - by nixnotwin
    I have the following setup: modem + router - - - - -Ubuntu box on master mode.........wireless devises. Ubuntu machine connects to Internet on wired network. I've dhcp3-server, masquerading, and wireless card with master mode on Ubuntu box. The issue is Ubuntu connects to the router on NAT. The wireless devises connect to the Ubuntu box on a NAT too (though different). SO my wireless devises are behind two NAT networks. The solution I am looking for is Ubuntu should forward dhcp requests to the modem+router, and Ubuntu should act as a switch or a bridge that allows wireless devises to connect to the wired network. So the modem+router should act a main router.

    Read the article

  • Cisco ASA - NAT'ing VPN traffic

    - by DrStalker
    I have an IPsec VPN setup like this: [Remote users]-[Remote ASA] <-VPN-> [My ASA]-[Subnet A]-[Router 2]-[Subnet B] The VPN is set to handle traffic between [remote users] and [Subnet A]; it does not include [Subnet B]. Pretend the firewall rules for all routers are to permit everything. Now I want to redirect traffic that comes over the VPN to a specific IP on [subnet A] (192.168.1.102) to an IP on [Subnet B] (10.1.1.133) If I add a rule on [My ASA] to NAT traffic to original IP 192.168.1.102 to new IP 10.1.1.133, 1) Will this affect the connections coming in over the VPN? (ie: the VPN packets are unencrypted and then NAT is applied) 2) Will this work when the post-NAT target is on Subnet-B, which is not part of the VPN traffic selection?

    Read the article

  • Squid3 not working. Access denied

    - by Nitish
    I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

    Read the article

  • Squid3 not working. Access denied.

    - by Nitish
    I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

    Read the article

  • Iptables string

    - by Mr. BeatMasta
    I have an iptables rule like this: iptables -t nat -I PREROUTING -p tcp --dport 80 -s 192.168.1.2 -j DNAT --to-destination 192.168.1.1:80 it works perfectly.. but I want to redirect only for one URL like this: iptables -t nat -I PREROUTING -p tcp --dport 80 -s 192.168.1.2 -m string --string "google.com" -j DNAT --to-destination 192.168.1.1:80 which does not work in any way... please help me with this

    Read the article

  • How to make sysctl network bridge settings persist after a reboot?

    - by Zack Perry
    I am setting up a notebook for software demo purpose. The machine has 8GB RAM, a Core i7 Intel CPU, a 128GB SSD, and runs Ubuntu 12.04 LTS 64bit. The notebook is used as a KVM host and runs a few KVM guests. All such guests use the virbr0 default bridge. To enable them to communicate with each other using multicast, I added the following to the host's /etc/sysctl.conf, as shown below net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 Afterwards, following man sysctl(8), I issued the following: sudo /sbin/sysctl -p /etc/sysctl.conf My understanding is that this should make these settings persist over reboots. I tested it, and was surprised to find out the following: root@sdn1 :/proc/sys/net/bridge# more *tables :::::::::::::: bridge-nf-call-arptables :::::::::::::: 1 :::::::::::::: bridge-nf-call-ip6tables :::::::::::::: 1 :::::::::::::: bridge-nf-call-iptables :::::::::::::: 1 All defaults are coming back! Yes. I can use some kludgy "get arounds" such as putting a /sbin/sysctl -p /etc/sysctl.conf into the host's /etc/rc.local but I would rather "do it right". Did I misunderstand the man page or is there something that I missed? Thanks for any hints. -- Zack

    Read the article

  • Creating static NAT blocks outbound traffic Cisco ASA

    - by natediggs
    Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

    Read the article

  • problems with ASA 8.4 Nat Rules for a Web Server

    - by Marko
    Having problems with the NAT RULES and Access Rules changes on my ASA5505. Want to straight replace a 5505 with a newer 5505 and unfortunately this means dealing with old version 7.2 and the newer 8.4 configurations. my old NAT RULE: static (inside,outside) WebOutside WebInside netmask 255.255.255.255 and an Access Rule of: access-list outside_access_in extended permit tcp any host WebOutside eq www these dont work in 8.4 I understand there are some changed but I can find little information that makes any sense on how to configure these. Any pointers welcomed.

    Read the article

  • Redirect all traffic to specified hosts behind NAT

    - by biesiad
    Is there a possibility to redirect all traffic to specified hosts behind NAT? For example i have a server, a domain "mydomain.com" and 3 hosts behind NAT. I wish to configure 3 subdomains: host1.mydomain.com host2.mydomain.com host2.mydomain.com and each of them to redirect all ports to specified host in local net. That redirection should provide funcionality like this: http://host1.mydomain.com (can be achieved using apache) ssh [email protected] (???) and other protocols on diferent ports Thanks for any help.

    Read the article

  • pfSense router on a LAN with two gateways

    - by JohnCC
    I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

    Read the article

  • FreeBSD's ng_nat stopping pass the packets periodically

    - by Korjavin Ivan
    I have FreeBSD router: #uname 9.1-STABLE FreeBSD 9.1-STABLE #0: Fri Jan 18 16:20:47 YEKT 2013 It's a powerful computer with a lot of memory #top -S last pid: 45076; load averages: 1.54, 1.46, 1.29 up 0+21:13:28 19:23:46 84 processes: 2 running, 81 sleeping, 1 waiting CPU: 3.1% user, 0.0% nice, 32.1% system, 5.3% interrupt, 59.5% idle Mem: 390M Active, 1441M Inact, 785M Wired, 799M Buf, 5008M Free Swap: 8192M Total, 8192M Free PID USERNAME THR PRI NICE SIZE RES STATE C TIME WCPU COMMAND 11 root 4 155 ki31 0K 64K RUN 3 71.4H 254.83% idle 13 root 4 -16 - 0K 64K sleep 0 101:52 103.03% ng_queue 0 root 14 -92 0 0K 224K - 2 229:44 16.55% kernel 12 root 17 -84 - 0K 272K WAIT 0 213:32 15.67% intr 40228 root 1 22 0 51060K 25084K select 0 20:27 1.66% snmpd 15052 root 1 52 0 104M 22204K select 2 4:36 0.98% mpd5 19 root 1 16 - 0K 16K syncer 1 0:48 0.20% syncer Its tasks are: NAT via ng_nat and PPPoE server via mpd5. Traffic through - about 300Mbit/s, about 40kpps at peak. Pppoe sessions created - 350 max. ng_nat is configured by by the script: /usr/sbin/ngctl -f- <<-EOF mkpeer ipfw: nat %s out name ipfw:%s %s connect ipfw: %s: %s in msg %s: setaliasaddr 1.1.%s There are 20 such ng_nat nodes, with about 150 clients. Sometimes, the traffic via nat stops. When this happens vmstat reports a lot of FAIL counts vmstat -z | grep -i netgraph ITEM SIZE LIMIT USED FREE REQ FAIL SLEEP NetGraph items: 72, 10266, 1, 376,39178965, 0, 0 NetGraph data items: 72, 10266, 9, 10257,2327948820,2131611,4033 I was tried increase net.graph.maxdata=10240 net.graph.maxalloc=10240 but this doesn't work. It's a new problem (1-2 week). The configuration had been working well for about 5 months and no configuration changes were made leading up to the problems starting. In the last few weeks we have slightly increased traffic (from 270 to 300 mbits) and little more pppoe sessions (300-350). Help me please, how to find and solve my problem?

    Read the article

  • Why are SIP calls via my server silent?

    - by Archcode
    I have FreeSWITCH SIP server up and running. It has public IP and sits behind 1-to-1 NAT (it's Amazon EC2 instance actually). I can connect to it, make a call to other endpoint (namely, my android device to my pc and vice versa) and signals are send with no problems (call, answer, hangup, etc). Unfortunately, and what drives me crazy, that's all: no audio gets through, no video either. Server does not throw errors, it reports many retransmission though, looks like this: switch_rtp.c:915 [ zrtp engine]: WARNING! HELLO Max retransmissions count reached (20 retries). ID=15 Codecs are set up correctly (same config worked locally on my LAN). NAT/firewall on client side may be a problem, signals do get through (perhaps due to fixed port, data streaming runs on random one, that is currently my best bet). STUN/TURN/ICE setting on client seem to have no effect. Endpoints sit behind symmetric NAT. On server there are no iptables rules, security group is set as suggested there: http://wiki.freeswitch.org/wiki/Firewall Help, please. How to make it work or at least diagnose what's wrong?

    Read the article

  • Cisco ASA not forwarding traffic from one interface to another

    - by Antoine Benkemoun
    Hello ServerFault, I am needing help in the configuration process of my Cisco ASA 5510. I have set up 4 Cisco ASA interconnected together via a big LAN. Each Cisco ASA has 3 or 4 LANs attached to them. The IP routing part is taken care of by OSPF. My problem is on another level. A computer connected to one of the LANs attached to an ASA has no problem communicating with the outside world. The outside world being anything "after" the ASA. My problem is that I am completely unable to have them communicate with another LAN connected to the same ASA. To rephrase this, I am unable to send traffic from one interface of a given ASA to another interface of the same ASA. My configuration is the following : ! hostname Fuji ! interface Ethernet0/0 speed 100 duplex full nameif outside security-level 0 ip address 10.0.0.2 255.255.255.0 no shutdown ! interface Ethernet0/1 speed 100 duplex full nameif cs4 no shutdown security-level 100 ip address 10.1.4.1 255.255.255.0 ! interface Ethernet0/2 speed 100 duplex full no shutdown ! interface Ethernet0/2.15 vlan 15 nameif cs5 security-level 100 ip address 10.1.5.1 255.255.255.0 ! interface Ethernet0/2.16 vlan 16 nameif cs6 security-level 100 ip address 10.1.6.1 255.255.255.0 ! interface Management0/0 speed 100 duplex full nameif management security-level 100 ip address 10.6.0.252 255.255.255.0 ! access-list nat_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list acl_cs4 extended permit ip 10.1.4.0 255.255.255.0 any access-list nat_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list acl_cs5 extended permit ip 10.1.5.0 255.255.255.0 any access-list nat_cs6 extended permit ip 10.1.6.0 255.255.255.0 any access-list acl_cs6 extended permit ip 10.1.6.0 255.255.255.0 any ! access-list nat_outside extended permit ip any any access-list acl_outside extended permit ip any 10.1.4.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.5.0 255.255.255.0 access-list acl_outside extended permit ip any 10.1.6.0 255.255.255.0 ! nat (outside) 0 access-list nat_outside nat (cs4) 0 access-list nat_cs4 nat (cs5) 0 access-list nat_cs5 nat (cs6) 0 access-list nat_cs6 ! static (outside,cs4) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs5) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 static (outside,cs6) 0.0.0.0 0.0.0.0 netmask 0.0.0.0 ! static (cs4,outside) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs5) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 static (cs4,cs6) 10.1.4.0 10.1.4.0 netmask 255.255.255.0 ! static (cs5,outside) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs4) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 static (cs5,cs6) 10.1.5.0 10.1.5.0 netmask 255.255.255.0 ! static (cs6,outside) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs4) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 static (cs6,cs5) 10.1.6.0 10.1.6.0 netmask 255.255.255.0 ! access-group acl_outside in interface outside access-group acl_cs4 in interface cs4 access-group acl_cs5 in interface cs5 access-group acl_cs6 in interface cs6 ! router ospf 1 network 10.0.0.0 255.255.255.0 area 1 network 10.1.4.0 255.255.255.0 area 1 network 10.1.5.0 255.255.255.0 area 1 network 10.1.6.0 255.255.255.0 area 1 log-adj-changes ! There is nothing really complicated in this configuration. It just NATs from one interface to another and that's it. I have tried enabling same-security-traffic permit inter-interface but that doesn't help. I therefore must be missing something a little bit more complicated. Does anyone know why I cannot foward traffic from one interface to another ? Thank you in advance for your help, Antoine

    Read the article

  • ISP 5 Device Limit ... again

    - by Tommo
    Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

    Read the article

  • Webserver on a rotating server with NAT IP or changing IPs

    - by hpsoftware
    i would have to elaborate my questions so please have patience Explaining the logic. if you are familiar with logmein then it installs a client software on your computer then it kinda keeps tracks where you computer is as long as it's connected to internet. So you can always access your computer no matter where it is whatever it's IP is you just go to logmein.com and then you can just access it. Now what i am asking 1. Let's assume i have a website hosted on my laptop let's call it webserver. so then i move around i have a new IP sometime even on a hotel network is it possible to do something like what logmein does so i can keep moving around my Webserver to new IP but it has some local client or something which keeps updating my IP or something i am sure i would need a gateway server somewhere which is connected to my domain name via DNS so somebody accessing my website www.mywebsite.com goes to my main server then gets routed to my laptop which could be anywhere but my gateway server is able to communicate to my webserver I will keep updating the case description based on comments to make more sense. please have patience with me. Regards

    Read the article

  • can't ping from virtualbox ubuntu server --nat connection

    - by George
    i set up an ubuntu server in virtual box following these and these instructions.My connection worked,also ssh . Then, i signed up in dyndns.com ,i configured the router ,but in the port forward i changed the 2222 port to 80 because it couldn’t forward from 2222.My port is open and accepting connections but i don’t have any more connection from the server in the virtual box. From virtual box settings-network-port forwarding , i use: Host IP :127.0.0.1 , Host port :80 , Guest Port :22 ,Guest IP : its empty. I am not sure if i am using right the address in /etc/network/interfaces , i use 192.168.0.2 and also this address i use for the firewall rules in the router. Also,in the server /etc/resolv.conf i put that address and in /etc/mysql/my.cnf. I can ping that address but nothing more.(of course neither ssh works) Thank you

    Read the article

  • Configure Cisco Pix 515 with DMZ and no NAT

    - by Rickard
    I hope that someone could shed some light over my situation, as I am fairly new to PIX configurations. I will be getting a new net for my department, which I am going to configure. At my hands, I have a Cisco PIX 515 (not E), a Cisco 2948 switch (and if needed, I can bring up a 2621XM router, but this is my private and not owned by my dept.). The network I will be getting is the following: 10.12.33.0/26 Link net between the ISP routers and my network will be 10.12.32.0/29 where GW is .1 and HSRP roututers are .2 and .3 The ISP has asked me not to NAT the addresses on my side, as they will set it up to give 10.12.33.2 as a one-to-one nat to a public IP. The rest of the IP's will be a many-to-one NAT to another public IP. 10.12.33.2 is supposed to be my server placed on the DMZ, the rest of the IP's will be used for my clients and the AD server (which is currently also acting as a DHCP server in the old network config with another ISP). Now, the question is, how would I best configure this? I mean, am I thinking wrong here, I am expected to put the PIX first from the ISP outlet, then to the switch which will connect my clients. But with the ISP routers being on a different network, how will the firewall forward the packets to the other network, it's a firewall, not a router. I have actually never configured a pix before, and fortunately, this is more like a lab network, not a production network, so if something goes wrong it's not the end of the world, if though annoying. I am not asking for a full configuration from anyone, just some directions, or possibly some links which will give me some hints. Thank you very much!

    Read the article

  • Network Restructure Method for Double-NAT network

    - by Adrian
    Due to a series of poor network design decisions (mostly) made many years ago in order to save a few bucks here and there, I have a network that is decidedly sub-optimally architected. I'm looking for suggestions to improve this less-than-pleasant situation. We're a non-profit with a Linux-based IT department and a limited budget. (Note: None of the Windows equipment we have runs does anything that talks to the Internet nor do we have any Windows admins on staff.) Key points: We have a main office and about 12 remote sites that essentially double NAT their subnets with physically-segregated switches. (No VLANing and limited ability to do so with current switches) These locations have a "DMZ" subnet that are NAT'd on an identically assigned 10.0.0/24 subnet at each site. These subnets cannot talk to DMZs at any other location because we don't route them anywhere except between server and adjacent "firewall". Some of these locations have multiple ISP connections (T1, Cable, and/or DSLs) that we manually route using IP Tools in Linux. These firewalls all run on the (10.0.0/24) network and are mostly "pro-sumer" grade firewalls (Linksys, Netgear, etc.) or ISP-provided DSL modems. Connecting these firewalls (via simple unmanaged switches) is one or more servers that must be publically-accessible. Connected to the main office's 10.0.0/24 subnet are servers for email, tele-commuter VPN, remote office VPN server, primary router to the internal 192.168/24 subnets. These have to be access from specific ISP connections based on traffic type and connection source. All our routing is done manually or with OpenVPN route statements Inter-office traffic goes through the OpenVPN service in the main 'Router' server which has it's own NAT'ing involved. Remote sites only have one server installed at each site and cannot afford multiple servers due to budget constraints. These servers are all LTSP servers several 5-20 terminals. The 192.168.2/24 and 192.168.3/24 subnets are mostly but NOT entirely on Cisco 2960 switches that can do VLAN. The remainder are DLink DGS-1248 switches that I am not sure I trust well enough to use with VLANs. There is also some remaining internal concern about VLANs since only the senior networking staff person understands how it works. All regular internet traffic goes through the CentOS 5 router server which in turns NATs the 192.168/24 subnets to the 10.0.0.0/24 subnets according to the manually-configured routing rules that we use to point outbound traffic to the proper internet connection based on '-host' routing statements. I want to simplify this and ready All Of The Things for ESXi virtualization, including these public-facing services. Is there a no- or low-cost solution that would get rid of the Double-NAT and restore a little sanity to this mess so that my future replacement doesn't hunt me down? Basic Diagram for the main office: These are my goals: Public-facing Servers with interfaces on that middle 10.0.0/24 network to be moved in to 192.168.2/24 subnet on ESXi servers. Get rid of the double NAT and get our entire network on one single subnet. My understanding is that this is something we'll need to do under IPv6 anyway, but I think this mess is standing in the way.

    Read the article

  • Nat skin with tinymce as the editor

    - by abhishekgupta92
    How can I have NAT Skin with TinyMCE as the editor in twiki. When I changed my skin to Nat in the twiki preferences my editor automatically got changed to natedit though i was working previously on tinymce editor and would like to do so in the future but with nat as the default skin.

    Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >