Search Results

Search found 22301 results on 893 pages for 'software sources'.

Page 800/893 | < Previous Page | 796 797 798 799 800 801 802 803 804 805 806 807  | Next Page >

  • Is my motherboard failing, or is there some other issue?

    - by ThatGuy
    So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

    Read the article

  • Why is my rsync so slow?

    - by iblue
    My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

    Read the article

  • sharing a USB printer in SOHO environment [migrated]

    - by Registered User
    Here is a situation I am facing, there is USB printer which works only on a Windows XP machine, there are other devices in LAN it is a Small Office Home Office environment. How can this USB printer attached to Windows XP machine be shared so that other laptops or users in Network who have Windows 7 or Linux on their laptops can use this printer. The printer model number is Canon Laser Shot LBP-1210 http://www.canon-europe.com/For_Home/Product_Finder/Printers/Laser/LaserShot_LBP1210/index.asp a print server is not available to me I need to make it work in this situation only.What can I do? the clients are unable to connect to this.It is not a network or TCP/IP printer If a from Windows 7 machine some one wants to use this printer so that he can take a print he gets an error while adding the printer to his machine which is a Windows 7 machine (where as the printer is USB printer on Windows XP machine) Start--->Devices and Printers---> Add Printer---> Find Printer by name or IP address--->Selected a shared printer by name-->\\PC-Name-printer3 and select browse it gives a message Windows can not find a driver for Canon LASER SHOT LBP-1210 on the network what does this mean do I need to install some kind of software at client machine or on the machine where printer is present?

    Read the article

  • Arduino IDE "launch 4j" error

    - by John
    I have a computer running Windows XP. I am trying to run the Arduino IDE 0022. I double-click on arduino.exe, it waits about 30 seconds on the load up title screen, and then it gives me this error: Launch 4j: an error occurred while starting the application My only choice is to click "OK"; the error goes away, and the Arduino IDE closes. If I try to delete the Arduino files (to try overwriting with some different files), I get an error that doesn't allow me to do so: Cannot delete awt.dll: Access denied Make sure the disk is not full or write protected and that the file is not currently in use. The only way to delete the file is by restarting the computer. So something must still be trying to run after that first error. I have noticed in Task Manager that some Java programs are still running: javaw.exe (3 processes) I think this is a problem with Java, but I checked and updated all of my Java software and it is all up to date. I have looked on other forums for this issue and none of them seemed to help. From the forums I have tried: Different Arduino IDE versions Updating Java Opening arduino.exe as Administrator Nothing has worked. Anyone have any suggestions?

    Read the article

  • Are there tools available for trimming PDF margins?

    - by Charles Duffy
    I have an ebook I'm trying to read in PDF format on a Kindle. Unfortunately, the page headers and footers have some content (page number and copyright info, respectively) preventing the device from scaling the actual text to match its usable area viewing area, thus leaving the actual content too small to read. Various tools are available which will trim off whitespace, but the Kindle already does this; my goal, by contrast, is to remove printed matter outside of a defined bounding box, and the only tool I've found for the purpose is moderately expensive commercial software. I could probably generate a mask in Inkscape; split out the individual pages using pdftk, apply the mask to each page individually (outputting to postscript), and recombine the numerous postscript files into a single PDF. However, this decode/reencode steps would be pretty unfortunate in terms of document size; something able to operate with a bit more finesse would be ideal. I have all major operating systems handy (Windows, several modern Linux distros, a Mac, etc) so solutions don't need to be constrained by platform. Suggestions? (I've reported the issue to the author, who mentioned it to his editor, who hasn't done anything about the issue over the course of more than a month, making the zero-work approach evidently nonproductive).

    Read the article

  • Datastage 8.7 installs fine on Window7 without any errors but it can not launch localhost:9080 web console

    - by user265273
    When I launch the web console, I get page can not be displayed error. What I have tried so far: I have re-installed DS about 7 times, and each time, I get same errors. I added entries in etc/hosts file for local host and my host name. I have turned off firewall. My hardware/software setup. My host system is window8.1. My vmware workstation is 7. The guest os is windows 7 enterprise x64. I have installed 10g, and given dba role to public. I have installed VS 5, and ms visual c++ 2010 express. I have installed msxml. IE version is 10. Firewall is off. My internet works fine It passed all the DS requirement tests and install completed successfully. When I launch my vmware guest instance, I do get SQL5000c error upon boot which I have tried to ignore in some installs and in some, I used db2systray -clean command to get rid of it. But that has not helped solve the webconsole connect failure to my host. I have spent over 2 weeks exclusively on this issue and badly need some help.

    Read the article

  • Despeckle line art

    - by Dour High Arch
    We have a number of line-art charts unfortunately saved as JPEGs. They are now riddled with distracting compression artifacts or "speckles". Is there any way of removing these? I do not have the original files and it will be very difficult to recreate them. I am running Windows 7 and tried Paint.Net; none of the filters help. Posterize washed out all the colors and leaves the speckles. Blur makes text unreadable. Noise Reduction wrecks antialiasing of curved lines, and perversely enhances the speckles, making them look like checkerboards. Yes, I have Googled for software to do this; there are many programs that advertise despeckling but, after my experience with Paint.Net, do not want to experiment with applications that show no before and after images. The only example I have seen that does what I want is from a Photoshop tutorial. I have dozens of files and the tutorial requires considerable manual fine-tuning. I would prefer to automate or batch-process this task. Commercial apps are fine, but I do not want to spend over $600 and learning a complex program for a single task.

    Read the article

  • Fixing Windows install by connecting its hard drive via USB to a different laptop

    - by Jason
    I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

    Read the article

  • Fixing Windows install by connecting it's hard drive via USB to a different laptop

    - by Jason
    I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

    Read the article

  • How do I connect to and factory reset a Catalyst 3560 Switch?

    - by Josh
    My company just bought another company. In their server room they had some older hardware, which I would like to repurpose. One of these is a Cisco Switch: C3560G-48TS-S. I found some instructions about this switch here but this is not a guide for a beginner. I have no idea how to connect to this thing to begin running the commands. It says Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. But I can't find anything on how to do this (assuming with telnet?) or even what program to use. I also don't know how to find the IP address of the device to connect to it. My research also says once I get in there, I need to run clear config all Is this the right command? Also, what if I can't get the username and password for these devices? Is there some way to factory reset (my only experience is with devices that have a hardware reset button) EDIT: I should note that when I push the button on the front the three lights blink, which according to the documentation indicated the switch is configured and "not available for express setup"

    Read the article

  • What Logs / Process Stats to monitor on a Ubuntu FTP server?

    - by Adam Salkin
    I am administering a server with Ubuntu Server which is running pureFTP. So far all is well, but I would like to know what I should be monitoring so that I can spot any potential stability and security issues. I'm not looking for sophisticated software, more an idea of what logs and process statistics are most useful for checking on the health of the system. I'm thinking that I can look at various parameters output from the "ps" command and compare to see if I have things like memory leaks. But I would like to know what experienced admins do. Also, how do I do a disk check so that when I reboot, I don't get a message saying something like "disk not checked for x days, forcing check" which delays the reboot? I assume there is command that I can run as a cron job late at night. How often should it be run? What things should I be looking at to spot intrusion attempts? The only shell access is SSH on a non-standard port through UFW firewall, and I regularly do a grep on auth.log for "Fail" or "Invalid". Is there anything else I should look at? I was logging the firewall (UFW) but I have very few open ports (FTP and SSH on a non standard port) so looking at lists of IP's that have been blocked did not seem useful. Many thanks

    Read the article

  • zsh : How to list directory content with tab?

    - by Philippe CM
    I just switched from BASH to ZSH and thing are pretty good, but: when I start typing cd /usr/share/s and hit TAB, this is what I get : $ cd /usr/share/sane/ sane/ skype/ ssl-cert/ screen/ smplayer/ strigi/ seed-gtk3/ snmp/ synaptic/ sgml/ software-properties/ system-config-printer/ sgml-base/ soprano/ sysv-rc/ sgml-data/ sounds/ simple-scan/ splashy/ And this is ok. If I then hit TAB again, I get $ cd /usr/share/screen/, the next candidate, witch is also OK. (BTW, how do I cycle back to the previous candidate? Sorry, on to my question) Now what if I want to see the contents of /usr/share/screen/ now ? You now, BASH-style? The cursor is at the end of the line, will I have to ctrl-a (or home), then del del (to erase cd) then ls then ENTER? That seems like a lot of typing. (And it - possibly unnecessarily - enters the command in the history) Would not there be a key (maybe modifier-TAB? but the obvious candidates are already taken by the desktop... I digress) that would tell zsh to stop cycling through /usr/share/ and instead, just list the content /usr/share/screen/ ?

    Read the article

  • How do I install Apache Portable Runtime?

    - by apache
    My Apache is installed by yum install apache And now I'm trying to install subversion server from source following instructions here. But when I try to configure,get an error: [root@vps303 subversion-1.6.9]# ./configure configure: Configuring Subversion 1.6.9 configure: creating config.nice checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes ... checking for APR... no configure: WARNING: APR not found The Apache Portable Runtime (APR) library cannot be found. Please install APR on this system and supply the appropriate --with-apr option to 'configure' or get it with SVN and put it in a subdirectory of this source: svn co \ http://svn.apache.org/repos/asf/apr/apr/branches/1.2.x \ apr Run that right here in the top level of the Subversion tree. Afterwards, run apr/buildconf in that subdirectory and then run configure again here. Whichever of the above you do, you probably need to do something similar for apr-util, either providing both --with-apr and --with-apr-util to 'configure', or getting both from SVN with: svn co \ http://svn.apache.org/repos/asf/apr/apr-util/branches/1.2.x \ apr-util configure: error: no suitable apr found How do I get around this problem? BTW,will both client and server software be installed by compiling from source?

    Read the article

  • Laptop + External Monitor: Possible to Scale Mouse-crossover Position?

    - by Brian Lacy
    I have a laptop with a 16" screen @ 1366x768 resolution, and a 24" external monitor at 1920x1200 resolution. I'm extending the Windows 7 desktop onto the other screen. The 24" is the secondary monitor, and is positioned so the bottom of that screen lines up with the bottom of the 16" screen. Currently, if I move the mouse to the top portion of the 24" screen, then move left, the mouse will stop at the edge of the 24" screen until I move it down far enough to get into the range of the 16" screen. So that's all pretty standard; but I'm wondering if there's any software out there that will allow me to "scale" the mouse-crossover position, such that if I'm at the TOP of the 24" screen and move left, the mouse will cross to the TOP of the 16" screen, whereas if I'm at the BOTTOM of the 24" screen, crossing over will position the mouse at the BOTTOM of the 16" screen. So then, if the mouse cursor is on the 24" screen at (x,y) position (10,600), and I move 20 pixels left, the mouse is now on the 16" screen at position (1356,384). Anyone know of such a solution?? Note: I also use Ubuntu, so if there's a solution to this for X, but not Windows, I'd be interested in that also.

    Read the article

  • Huh? JDK not found? (on Windows 7 64-bit)

    - by Android Eve
    I am setting up a development environment for the latest Android 2.3 on a fresh install of Windows 7 64-bit. I first installed the 64-bit JDK 6 (jdk-6u23-windows-x64.exe). Then, I installed 64-bit Eclipse Classic 3.6 (eclipse-SDK-3.6.1-win32-x86_64.zip). Then, I proceed to install the Android SDK Starter Package: installer_r08-windows.exe. But... upon start it says: "Java SE Development Kit (JDK) not found." Why? I just installed it. Is this a mismatch between 32-bit and 64-bit? How do I solve this? Update (1): I tried setting the %JAVA_HOME% environment variable, as well as setting the Installed JREs in Eclipse, as suggested below. None of these solved the problem. It appears that I am not the only experiencing the problem, as this thread suggests: http://stackoverflow.com/questions/1919340/android-sdk-setup-under-windows-7-pro-64-bit I wonder whether there is a 64-bit version of the Android SDK. Update (2): I used the zip version instead (android-sdk_r08-windows.zip), ran android.bat, updated all SDK packages, and installed the ADT plugin (8.0.1), not before having to check: 'Contact all update sites during install to find required software'. We'll see how this goes... Update (3): It worked! (going to accept @bubu's answer shortly) -- but why doesn't the emulator include the HelloAndroid app when I run it (Ctrl+F11) from Eclipse?

    Read the article

  • Optimize Apache performance

    - by Phliplip
    I'm looking for ways to optimize our current web server hosted in-house. I'm trying to supply as much relevant information below. Please let me know if you would require additional information in order to assist. Server is running 1 single website, which is an online pizza ordering platform built on Zend Framework (ver1). On traffic stats from the last month aprox 6.000 pageloads per day, concentrated mainly around dinnertime. Around 1500 loads/hour peaks in that period. We recently upgraded from a 2/2mbit aDSL-line to 100/100mbit fiber, and we still have performance issues at dinner time. We assumed the 2mbit was the issue. Website is pretty snappy in low-load periods. Hardware CPU: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz (3000.13-MHz K8-class CPU) Mem: 328M Active, 4427M Inact, 891M Wired, 244M Cache, 623M Buf, 33M Free Swap: 16G Total, 468K Used, 16G Free (6GB physical, 16GB swap) Filesystem Type Size Used Avail Capacity Mounted on /dev/ad7s1a ufs 4.8G 768M 3.7G 17% / devfs devfs 1.0K 1.0K 0B 100% /dev /dev/ad7s1g ufs 176G 5.2G 157G 3% /home /dev/ad7s1e ufs 4.8G 2.8M 4.5G 0% /tmp /dev/ad7s1f ufs 19G 3.5G 14G 19% /usr /dev/ad7s1d ufs 4.8G 550M 3.9G 12% /var Server OS FreeBSD 8.2-RELEASE Software apache-2.2.17 php5-5.3.8 mysql-server-5.5 Apache footprint (example, taken from # top) 31140 www 1 45 0 377M 41588K lockf 2 0:00 0.00% httpd 31122 www 1 44 0 375M 35416K lockf 2 0:00 0.00% httpd 31109 www 1 44 0 375M 38188K lockf 2 0:00 0.00% httpd 31113 www 1 44 0 375M 35188K lockf 2 0:00 0.00% httpd Apache is using the prefork MPM, APC (Alternative PHP Cache). SSL module is loaded, but not utilized (as in don't really work, thus not used). There is a file containing settings for MPM modules, but as i see it's not included in the httpd.conf file, the include line is commented out. Thus i would guess that the prefork MPM is working of default values too. Here are some other Apache conf values that i found - which are included in https.conf Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 UseCanonicalName Off HostnameLookups Off

    Read the article

  • How can I get DVDs playing after a Vista to XP change?

    - by Liath
    I replaced my vista install on a Dell Inspiron 1525 with XP and have managed to get most things up and running again however I'm having trouble with playing DVDs. When I try and play a DVD I get the following message: Windows Media Player cannot play this DVD because there is a problem with digital copy protection between your DVD drive, decoder, and video card. Try installing an updated driver for your video card. I have ensured that my drive is configured to play Region 2 discs (I'm in the UK), I've installed the most up to date XP codec pack which makes me think it's a driver issue. In device manager I have got my DVD drivers up to date however under "Other Devices" I'm missing several which sound key: Audio Device on High Definition Audio Bus Modem Device on High Definition Audio Bus Video Controller Video Controller (VGA Compatible) However I've installed all the relevant drivers I can find on the Dell website. The drive itself is working - I've run software from the drive. I'm afraid I am far from a sys-admin so I'm struggling on this one. How can I get my DVDs playing again?

    Read the article

  • Network card shuts down when stressed

    - by user142485
    I have a network card that functions fine with light use, but quits functioning after heavy use. I replaced it with a brand new one and still have the same issue, also updated drivers. It is a wired D-Link card. The Internet seems fine for a small amount of web browsing but when I run a bandwidth test it starts out fast and slows quickly until the card completely quits; I have a constant ping of the gateway going while I run this and it starts timing out after a couple seconds into the speed test. The card will stay on and the data light on it still flashes some but I cannot ping the gateway or anything else until the computer is rebooted. When I boot into safe mode I can browse and run the speed test fine with no problems. I am guessing that this is probably some program that is loading in regular mode but not safe mode that is causing the issue? I have very limited software (turned off av and firewall) on the computer but I am thinking that I'll just have to start eliminating start-up programs and see if that helps. This is on Windows 7 if that makes any difference. Anyone had a similar issue or have any other suggestions/ideas for narrowing down this problem?

    Read the article

  • Games on windows 8 in bootcamp lag even on lowest graphics

    - by Jackson Gariety
    I've been playing Crysis 2 and Skyrim on my Retina MacBookPro (10,1) for months now. The two games used to run super smoothly even on nearly maxed out settings. This laptop has an Nvidia GeForce GT 650M graphics card inside, it runs great. But I recently replaced my Windows 8 consumer preview with the retail copy, and since then, 3D games lag in this odd way, no matter what the graphics settings. Every second Skyrim and Crysis alternates between running smoothly and lagging. It's a cyclical lag that comes and goes like clockwork. I can turn the graphics down to 800x600 with no antialiasing and low texture quality, and it runs much smoother on the "up" motion of the cycle, but every second it moves back into this lag spike. I've tried installing beta graphics drivers, re installing the operating system, re installing the bootcamp support software, and freeing up space (I have about 20 GB free). I can't figure out what suddenly caused this other than some obscure difference between the consumer preview and the retail version. What can I try? Is my video card failing? Are there some other drivers I can install? This isn't normal lag from maxing out the card, it

    Read the article

  • Where does Windows store MSI files for uninstallation?

    - by Nilzor
    I'm trying to figure out how Windows (XP through 7) is handling installation and uninstallation of MSI files. I have come up in situations where Windows Installer is unable to uninstall because it's missing the original MSI file, which leads me to believe that it stores a copy of all installed MSI packages somewhere. Where? I've had a couple of theories. It expectes it to reside in the same folder as it was installed from. The registry keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall does point to the original installation folder, and error messages when the MSI file is missing often point to this. Removing the MSI file from this folder does not hinder the uninstallation process though, so I've refused this theory. C:\Windows\Installer. This folder actually contains a bunch of seemingly randomly named MSI files. But this list is incomplete. I do find entries in the registry key mentioned in 1) which does not have an MSI copy in this folder. So how does this work? How is windows installer able to uninstall MSI-installed applications even though the MSI is not in 1) and not in 2)?

    Read the article

  • What tools can I use to locate the IP of a machine on my network?

    - by user134918
    I am logged in to a remote Windows Server machine and am trying to attach it to a VPN for a LAN that I am also connected to locally from another Windows machine using Remotr Desktop. I can connect the remote machine to the VPN but when I do so, I lose my remote desktop connection. I am now in a situation where I know/think that the remote machine is on my LAN, but do not know what its current IP is and can therefor not connect to it again. I do not have any control over the infrastructure, all I have is a remote machine that I do control, and another machine that I also control that is connected to the same LAN as I'm trying to get the remote machine on using the existing VPN. What tools are available for Windows to allow me to locate the machine on my LAN again? I am imagining that there must be a tool that broadcasts the machines new IP using multicast, or tries to log in to a server component running somewhere with a know IP. Effectively, I am looking for some software that I can run on my remote machine, as well as my local machine, to allow me to discover the new IP address (on the LAN) assigned to the remote machine after connecting to the VPN.

    Read the article

  • Using multiple USB webcams in Linux

    - by rachelderp
    Running more than one USB webcam in Debian/Linux results in the the following error: libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON: No space left on device What initially seemed to be a programming issue in OpenCV turned into a quest for a mysterious hardware/software problem after the same errors were produced by running cheese and xawtv. Apparently it's caused by webcams requesting all the available bandwidth on the USB host controller. With that in mind I decided to run wireshark and capinfos to see just how much bandwidth a single camera used. 4 megabits per second at 320x240 14 megabits per second at 640x480 32 megabits per second at 1920x1080 Interesting! That might explain why two cameras at 320x240 work but any higher resolution fails. It's as if my USB controller is only operating at USB 1 speeds, yet lsusb shows both webcams belonging to a device which supposedly supports 480 megabits per second. One solution proposed forcing the webcams to calculate their bandwidth usage instead of requesting their maximum by running the following commands: sudo rmmod uvcvideo sudo modprobe uvcvideo quirks=128 Unfortunately that made no difference, so I decided to try another solution. A post on StackOverflow suggested telling my webcams to use a lower FPS or compressed video format like MJPEG, but after running v4lctl list it doesn't appear either of my webcams support changing their video mode. And that's where I'm stuck. Why would two webcams operating well below the maximum speed of USB 2 would produce this error? ps: It's not a disk space issue, df displays no change when the webcams are started. pps: If it makes a difference, here's the output of lsusb

    Read the article

  • Kindle (client) for Mac--text search or highlighting/notes?

    - by doug
    just so we're clear, i'm talking about the client/software version here--ie, that you install on your Mac or PC--not the device. The Kindle client was recently released for the Mac. I downloaded it and bought a couple of Kindle-edition books to view on this client. Astonishingly, two features i consider to be more or less essential to any ebook reader are missing in the Kindle client, either that, or i can't find them: (i) text searching; and (ii) highlighting text. First, does anyone know how to access the search feature? I'm aware of the "Go To" button at the top middle of the reader window--the options in that menu when you click the button are: "Cover", "Table of Contents", "Beginning" and "Location." "Location" requires that you type in an integer (but it doesn't correspond to page number--e.g., typing "167" brought me to the table of contents), not a search term. Second, there's a button on the upper right-hand corner of the window "Show Notes and Marks" yet i can't find any way to highlight text. The only kind of "note" or "mark" i have been able to record is to "bookmark" a page by clicking the "bookmark" button also at the top of the window.

    Read the article

  • Modifying value of "Rating" column within Explorer for arbitrary file types.

    - by Fake Name
    Basically, I have a large body of assorted media (text, images, flash files, archives, folders, etc...) and I'm attempting to organize it. Windows Explorer has a rating column, but there seems to be no way to modify the rating of the files short of opening them in their type-specific software (e.g. Media player, or Photo viewer). However, this does not work when the file is of an unsupported type (.rar, .swf ...), or a directory. I'd be more than willing to consider a file-manager replacement (I've alreadly looked at quite a few, Directory Opus, Total Commander, etc...), or even a solution that stores the rating metadata in a hidden file in each folder, or a separate database. The one real critical requirement is the ability to sort by rating, and being filetype-agnostic. Basically, is there any way to categorize a large collection of assorted files by rating that will work with any file type, including directories? - Ideally, there would be an easy way to add arbitrary columns to windows explorer, and edit them directly. However, there seems to be no way to do this. The rating column is the next best thing.

    Read the article

  • How should an experienced Windows SysAdmin learn Linux? [closed]

    - by Systemspoet
    I have a new hire starting in a few weeks who is an experienced Windows SysAdmin. I think he's fairly senior on the Windows side, with a pretty deep AD understanding and experience with Exchange 2007, 2010, and exchange migrations. He's done a little PowerShell but I suspect more of the "run this command to do this" variety then "write a script to do this" sort. However, we are a mixed shop and (he knows this) I expect him to become a reasonably competent Linux SysAdmin over time. I'm looking for good starting points to bring him along. I have over ten years of Linux/UNIX experience, so it all sort of seems intuitive to me, but I've been thinking about the toolkit you actually need to be productive in the Linux CLI world. Just to be able to use the machines at all, off the top of my head... vi Basic CLI stuff -- move around, rename files, copy files, tar, gzip, changing passwords, finding relevant manpages, keep track of where you are, find things in your history, etc, etc. More advanced things that I take for granted but are actually pretty hard -- doing things with 'find', extracting relevant text via 'awk' and/or 'cut', knowing when to use 'grep' and when to use 'grep -e' or 'egrep'. Distribution specific stuff... compiling software, rpm, yum, apt-get, you name it. This all seems pretty basic to me, but when I think back to 1995 when I was first learning my way, some of those things took me years to master. So my question is -- where should I send him to pick up those skills? I'm not just thinking of classes, but rather also websites and books? Where do you all suggest as a starting point for picking up Linux skills?

    Read the article

< Previous Page | 796 797 798 799 800 801 802 803 804 805 806 807  | Next Page >