Search Results

Search found 20691 results on 828 pages for 'iso image'.

Page 804/828 | < Previous Page | 800 801 802 803 804 805 806 807 808 809 810 811  | Next Page >

• Cisco PIX 8.0.4, static address mapping not working?

  - by Bill

  upgrading a working Pix running 5.3.1 to 8.0.4. The memory/IOS upgrade went fine, but the 8.0.4 configuration is not quite working 100%. The 5.3.1 config on which it was based is working fine. Basically, I have three networks (inside, outside, dmz) with some addresses on the dmz statically mapped to outside addresses. The problem seems to be that those addresses can't send or receive traffic from the outside (Internet.) Stuff on the DMZ that does not have a static mapping seems to work fine. So, basically: Inside - outside: works Inside - DMZ: works DMZ - inside: works, where the rules allow it DMZ (non-static) - outside: works But: DMZ (static) - outside: fails Outside - DMZ: fails (So, say, udp 1194 traffic to .102, http to .104) I suspect there's something I'm missing with the nat/global section of the config, but can't for the life of me figure out what. Help, anyone? The complete configuration is below. Thanks for any thoughts! ! PIX Version 8.0(4) ! hostname firewall domain-name asasdkpaskdspakdpoak.com enable password xxxxxxxx encrypted passwd xxxxxxxx encrypted names ! interface Ethernet0 nameif outside security-level 0 ip address XX.XX.XX.100 255.255.255.224 ! interface Ethernet1 nameif inside security-level 100 ip address 192.168.68.1 255.255.255.0 ! interface Ethernet2 nameif dmz security-level 10 ip address 192.168.69.1 255.255.255.0 ! boot system flash:/image.bin ftp mode passive dns server-group DefaultDNS domain-name asasdkpaskdspakdpoak.com access-list acl_out extended permit udp any host XX.XX.XX.102 eq 1194 access-list acl_out extended permit tcp any host XX.XX.XX.104 eq www access-list acl_dmz extended permit tcp host 192.168.69.10 host 192.168.68.17 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq ssh access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 192.168.68.0 255.255.255.0 eq 5901 access-list acl_dmz extended permit udp host 192.168.69.103 any eq ntp access-list acl_dmz extended permit udp host 192.168.69.103 any eq domain access-list acl_dmz extended permit tcp host 192.168.69.103 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.100 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.101 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.101 eq 3306 access-list acl_dmz extended permit tcp host 192.168.69.104 host 192.168.68.102 eq 3306 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8080 access-list acl_dmz extended permit tcp 10.71.83.0 255.255.255.0 host 192.168.69.104 eq 8099 access-list acl_dmz extended permit tcp host 192.168.69.105 any eq www access-list acl_dmz extended permit tcp host 192.168.69.103 any eq smtp access-list acl_dmz extended permit tcp host 192.168.69.105 host 192.168.68.103 eq ssh access-list acl_dmz extended permit tcp host 192.168.69.104 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq www access-list acl_dmz extended permit tcp host 192.168.69.100 any eq https pager lines 24 mtu outside 1500 mtu inside 1500 mtu dmz 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 static (dmz,outside) XX.XX.XX.103 192.168.69.11 netmask 255.255.255.255 static (inside,dmz) 192.168.68.17 192.168.68.17 netmask 255.255.255.255 static (inside,dmz) 192.168.68.100 192.168.68.100 netmask 255.255.255.255 static (inside,dmz) 192.168.68.101 192.168.68.101 netmask 255.255.255.255 static (inside,dmz) 192.168.68.102 192.168.68.102 netmask 255.255.255.255 static (inside,dmz) 192.168.68.103 192.168.68.103 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.104 192.168.69.100 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.105 192.168.69.105 netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.102 192.168.69.10 netmask 255.255.255.255 access-group acl_out in interface outside access-group acl_dmz in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.97 1 route dmz 10.71.83.0 255.255.255.0 192.168.69.10 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet 192.168.68.17 255.255.255.255 inside telnet timeout 5 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global prompt hostname context Cryptochecksum:2d1bb2dee2d7a3e45db63a489102d7de

  Read the article

• SQL SERVER – Step by Step Guide to Beginning Data Quality Services in SQL Server 2012 – Introduction to DQS

  - by pinaldave

  Data Quality Services is a very important concept of SQL Server. I have recently started to explore the same and I am really learning some good concepts. Here are two very important blog posts which one should go over before continuing this blog post. Installing Data Quality Services (DQS) on SQL Server 2012 Connecting Error to Data Quality Services (DQS) on SQL Server 2012 This article is introduction to Data Quality Services for beginners. We will be using an Excel file Click on the image to enlarge the it. In the first article we learned to install DQS. In this article we will see how we can learn about building Knowledge Base and using it to help us identify the quality of the data as well help correct the bad quality of the data. Here are the two very important steps we will be learning in this tutorial. Building a New Knowledge Base  Creating a New Data Quality Project Let us start the building the Knowledge Base. Click on New Knowledge Base. In our project we will be using the Excel as a knowledge base. Here is the Excel which we will be using. There are two columns. One is Colors and another is Shade. They are independent columns and not related to each other. The point which I am trying to show is that in Column A there are unique data and in Column B there are duplicate records. Clicking on New Knowledge Base will bring up the following screen. Enter the name of the new knowledge base. Clicking NEXT will bring up following screen where it will allow to select the EXCE file and it will also let users select the source column. I have selected Colors and Shade both as a source column. Creating a domain is very important. Here you can create a unique domain or domain which is compositely build from Colors and Shade. As this is the first example, I will create unique domain – for Colors I will create domain Colors and for Shade I will create domain Shade. Here is the screen which will demonstrate how the screen will look after creating domains. Clicking NEXT it will bring you to following screen where you can do the data discovery. Clicking on the START will start the processing of the source data provided. Pre-processed data will show various information related to the source data. In our case it shows that Colors column have unique data whereas Shade have non-unique data and unique data rows are only two. In the next screen you can actually add more rows as well see the frequency of the data as the values are listed unique. Clicking next will publish the knowledge base which is just created. Now the knowledge base is created. We will try to take any random data and attempt to do DQS implementation over it. I am using another excel sheet here for simplicity purpose. In reality you can easily use SQL Server table for the same. Click on New Data Quality Project to see start DQS Project. In the next screen it will ask which knowledge base to use. We will be using our Colors knowledge base which we have recently created. In the Colors knowledge base we had two columns – 1) Colors and 2) Shade. In our case we will be using both of the mappings here. User can select one or multiple column mapping over here. Now the most important phase of the complete project. Click on Start and it will make the cleaning process and shows various results. In our case there were two columns to be processed and it completed the task with necessary information. It demonstrated that in Colors columns it has not corrected any value by itself but in Shade value there is a suggestion it has. We can train the DQS to correct values but let us keep that subject for future blog posts. Now click next and keep the domain Colors selected left side. It will demonstrate that there are two incorrect columns which it needs to be corrected. Here is the place where once corrected value will be auto-corrected in future. I manually corrected the value here and clicked on Approve radio buttons. As soon as I click on Approve buttons the rows will be disappeared from this tab and will move to Corrected Tab. If I had rejected tab it would have moved the rows to Invalid tab as well. In this screen you can see how the corrected 2 rows are demonstrated. You can click on Correct tab and see previously validated 6 rows which passed the DQS process. Now let us click on the Shade domain on the left side of the screen. This domain shows very interesting details as there DQS system guessed the correct answer as Dark with the confidence level of 77%. It is quite a high confidence level and manual observation also demonstrate that Dark is the correct answer. I clicked on Approve and the row moved to corrected tab. On the next screen DQS shows the summary of all the activities. It also demonstrates how the correction of the quality of the data was performed. The user can explore their data to a SQL Server Table, CSV file or Excel. The user also has an option to either explore data and all the associated cleansing info or data only. I will select Data only for demonstration purpose. Clicking explore will generate the files. Let us open the generated file. It will look as following and it looks pretty complete and corrected. Well, we have successfully completed DQS Process. The process is indeed very easy. I suggest you try this out yourself and you will find it very easy to learn. In future we will go over advanced concepts. Are you using this feature on your production server? If yes, would you please leave a comment with your environment and business need. It will be indeed interesting to see where it is implemented. Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Business Intelligence, Data Warehousing, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: Data Quality Services, DQS

  Read the article

• Building the Ultimate SharePoint 2010 Development Environment

  - by Manesh Karunakaran

  It’s been more than a month since SharePoint 2010 RTMed. And a lot of people have downloaded and set up their very own SharePoint 2010 development rigs. And quite a few people have written blogs about setting up good development environments, there is even an MSDN article on it. Two of the blogs worth noting are from MVPs Sahil Malik and Wictor Wilén. Make sure that you check these out as well. Part of the bad side-effects of being a geek is the need to do the technical stuff the best way possible (pragmatic or otherwise), but the problem with this is that what is considered “best” is relative. Precisely the reason why you are reading this post now. Most of the posts that I read are out dated/need updations or are using the wrong OS’es or virtualization solutions (again, opinions vary) or using them the wrong way. Here’s a developer’s view of Building the Ultimate SharePoint 2010 Development Rig. If you are a sales guy, it’s time to close this window. Confusion 1: Which Host Operating System and Virtualization Solution to use? This point has been beaten to death in numerous blog posts in the past, if you have time to invest, read this excellent post by our very own SharePoint Joel on this subject. But if you are planning to build the Ultimate Development Rig, then Windows Server 2008 R2 with Hyper-V is the option that you should be looking at. I have been using this as my primary OS for about 6-7 months now, and I haven’t had any Driver issue or Application compatibility issue. In my experience all the Windows 7 drivers work fine with WIN2008 R2 also. You can enable Aero for eye candy (and the Windows 7 look and feel) and except for a few things like the Hibernation support (which a can be enabled if you really want it), Windows Server 2008 R2, is the best Workstation OS that I have used till date. But frankly the answer to this question of which OS to use depends primarily on one question - Are you willing to change your primary OS? If the answer to that is ‘Yes’, then Windows 2008 R2 with Hyper-V is the best option, if not look at vmWare or VirtualBox, both are equally good. Those who are familiar with a Virtual PC background might prefer Sun VirtualBox. Besides, these provide support for running 64 bit guest machines on 32 bit hosts if the underlying hardware is truly 64 bit. See my earlier post on this. Since we are going to make the ultimate rig, we will use Windows Server 2008 R2 with Hyper-V, for reasons mentioned above. Confusion 2: Should I use a multi-(virtual) server set up? A lot of people use multiple servers for their development environments - like Wictor Wilén is suggesting - one server hosting the Active directory, one hosting SharePoint Server and another one for SQL Server. True, this mimics the production environment the best possible way, but as somebody who has fallen for this set up earlier, I can tell you that you don’t really get anything by doing this. Microsoft has done well to ensure that if you can do it on one machine, you can do it in a farm environment as well. Besides, when you run multiple Server class machine instances in parallel, there are a lot of unwanted processor cycles wasted for no good use. In my personal experience, as somebody who needs to switch between MOSS 2007/SharePoint 2010 environments from time to time, the best possible solution is to Make the host Windows Server 2008 R2 machine your Domain Controller (AD Server) Make all your Virtual Guest OS’es join this domain. Have each Individual Guest OS Image have it’s own local SQL Server instance. The advantages are that you can reuse the users and groups in each of the Guest operating systems, you can manage the users in one place, AD is light weight and doesn't take too much resources on your host machine and also having separate SQL instances for each of the Development images gives you maximum flexibility in terms of configuration, for example your SharePoint rigs can have simpler DB configurations, compared to your MS BI blast pits. Confusion 3: Which Operating System should I use to run SharePoint 2010 Now that’s a no brainer. Use Windows 2008 R2 as your Guest OS. When you are building the ultimate rig, why compromise? If you are planning to run Windows Server 2008 as your Guest OS, there are a few patches that you need to install at different times during the installation, for that follow the steps mentioned here Okay now that we have made our choices, let’s get to the interesting part of building the rig, Step 1: Prepare the host machine – Install Windows Server 2008 R2 Install Windows Server 2008 R2 on your best Desktop/Laptop. If you have read this far, I am quite sure that you are somebody who can install an OS on your own, so go ahead and do that. Make sure that you run the compatibility wizard before you go ahead and nuke your current OS. There are plenty of blogs telling you how to make a good Windows 2008 R2 Workstation that feels and behaves like a Windows 7 machine, follow one and once you are done, head to Step 2. Step 2: Configure the host machine as a Domain Controller Before we begin this, let me tell you, this step is completely optional, you don’t really need to do this, you can simply use the local users on the Guest machines instead, but if this is a much cleaner approach to manage users and groups if you run multiple guest operating systems.  This post neatly explains how to configure your Windows Server 2008 R2 host machine as a Domain Controller. Follow those simple steps and you are good to go. If you are not able to get it to work, try this. Step 3: Prepare the guest machine – Install Windows Server 2008 R2 Open Hyper-V Manager Choose to Create a new Guest Operating system Allocate at least 2 GB of Memory to the Guest OS Choose the Windows 2008 R2 Installation Media Start the Virtual Machine to commence installation. Once the Installation is done, Activate the OS. Step 4: Make the Guest operating systems Join the Domain This step is quite simple, just follow these steps below, Fire up Hyper-V Manager, open your Guest OS Click on Start, and Right click on ‘Computer’ and choose ‘Properties’ On the window that pops-up, click on ‘Change Settings’ On the ‘System Properties’ Window that comes up, Click on the ‘Change’ button Now a window named ‘Computer Name/Domain Changes’ opens up, In the text box titled Domain, type in the Domain name from Step 2. Click Ok and windows will show you the welcome to domain message and ask you to restart the machine, click OK to restart. If the addition to domain fails, that means that you have not set up networking in Hyper-V for the Guest OS to communicate with the Host. To enable it, follow the steps I had mentioned in this post earlier. Step 5: Install SQL Server 2008 R2 on the Guest Machine SQL Server 2008 R2 gets installed with out hassle on Windows Server 2008 R2. SQL Server 2008 needs SP2 to work properly on WIN2008 R2. Also SQL Server 2008 R2 allows you to directly add PowerPivot support to SharePoint. Choose to install in SharePoint Integrated Mode in Reporting Server Configuration. Step 6: Install KB971831 and SharePoint 2010 Pre-requisites Now install the WCF Hotfix for Microsoft Windows (KB971831) from this location, and SharePoint 2010 Pre-requisites from the SP2010 Installation media. Step 7: Install and Configure SharePoint 2010 Install SharePoint 2010 from the installation media, after the installation is complete, you are prompted to start the SharePoint Products and Technologies Configuration Wizard. If you are using a local instance of Microsoft SQL Server 2008, install the Microsoft SQL Server 2008 KB 970315 x64 before starting the wizard. If your development environment uses a remote instance of Microsoft SQL Server 2008 or if it has a pre-existing installation of Microsoft SQL Server 2008 on which KB 970315 x64 has already been applied, this step is not necessary. With the wizard open, do the following: Install SQL Server 2008 KB 970315 x64. After the Microsoft SQL Server 2008 KB 970315 x64 installation is finished, complete the wizard. Alternatively, you can choose not to run the wizard by clearing the SharePoint Products and Technologies Configuration Wizard check box and closing the completed installation dialog box. Install SQL Server 2008 KB 970315 x64, and then manually start the SharePoint Products and Technologies Configuration Wizard by opening a Command Prompt window and executing the following command: C:\Program Files\Common Files\Microsoft Shared Debug\Web Server Extensions\14\BIN\psconfigui.exe The SharePoint Products and Technologies Configuration Wizard may fail if you are using a computer that is joined to a domain but that is not connected to a domain controller. Step 8: Install Visual Studio 2010 and SharePoint 2010 SDK Install Visual Studio 2010 Download and Install the Microsoft SharePoint 2010 SDK Step 9: Install PowerPivot for SharePoint and Configure Reporting Services Pop-In the SQLServer 2008 R2 installation media once again and install PowerPivot for SharePoint. This will get added as another instance named POWERPIVOT. Configure Reporting Services by following the steps mentioned here, if you need to get down to the details on how the integration between SharePoint 2010 and SQL Server 2008 R2 works, see Working Together: SQL Server 2008 R2 Reporting Services Integration in SharePoint 2010 an excellent article by Alan Le Marquand Step 10: Download and Install Sample Databases for Microsoft SQL Server 2008R2 SharePoint 2010 comes with a lot of cool stuff like PerformancePoint Services and BCS, if you need to try these out, you need to have data in your databases. So if you want to save yourself the trouble of creating sample data for your PerformancePoint and BCS experiments, download and install Sample Databases for Microsoft SQL Server 2008R2 from CodePlex. And you are done! Fire up your Visual Studio 2010 and Start Coding away!!

  Read the article

• Running a simple integration scenario using the Oracle Big Data Connectors on Hadoop/HDFS cluster

  - by hamsun

  Between the elephant ( the tradional image of the Hadoop framework) and the Oracle Iron Man (Big Data..) an english setter could be seen as the link to the right data Data, Data, Data, we are living in a world where data technology based on popular applications , search engines, Webservers, rich sms messages, email clients, weather forecasts and so on, have a predominant role in our life. More and more technologies are used to analyze/track our behavior, try to detect patterns, to propose us "the best/right user experience" from the Google Ad services, to Telco companies or large consumer sites (like Amazon:) ). The more we use all these technologies, the more we generate data, and thus there is a need of huge data marts and specific hardware/software servers (as the Exadata servers) in order to treat/analyze/understand the trends and offer new services to the users. Some of these "data feeds" are raw, unstructured data, and cannot be processed effectively by normal SQL queries. Large scale distributed processing was an emerging infrastructure need and the solution seemed to be the "collocation of compute nodes with the data", which in turn leaded to MapReduce parallel patterns and the development of the Hadoop framework, which is based on MapReduce and a distributed file system (HDFS) that runs on larger clusters of rather inexpensive servers. Several Oracle products are using the distributed / aggregation pattern for data calculation ( Coherence, NoSql, times ten ) so once that you are familiar with one of these technologies, lets says with coherence aggregators, you will find the whole Hadoop, MapReduce concept very similar. Oracle Big Data Appliance is based on the Cloudera Distribution (CDH), and the Oracle Big Data Connectors can be plugged on a Hadoop cluster running the CDH distribution or equivalent Hadoop clusters. In this paper, a "lab like" implementation of this concept is done on a single Linux X64 server, running an Oracle Database 11g Enterprise Edition Release 11.2.0.4.0, and a single node Apache hadoop-1.2.1 HDFS cluster, using the SQL connector for HDFS. The whole setup is fairly simple: Install on a Linux x64 server ( or virtual box appliance) an Oracle Database 11g Enterprise Edition Release 11.2.0.4.0 server Get the Apache Hadoop distribution from: http://mir2.ovh.net/ftp.apache.org/dist/hadoop/common/hadoop-1.2.1. Get the Oracle Big Data Connectors from: http://www.oracle.com/technetwork/bdc/big-data-connectors/downloads/index.html?ssSourceSiteId=ocomen. Check the java version of your Linux server with the command: java -version java version "1.7.0_40" Java(TM) SE Runtime Environment (build 1.7.0_40-b43) Java HotSpot(TM) 64-Bit Server VM (build 24.0-b56, mixed mode) Decompress the hadoop hadoop-1.2.1.tar.gz file to /u01/hadoop-1.2.1 Modify your .bash_profile export HADOOP_HOME=/u01/hadoop-1.2.1 export PATH=$PATH:$HADOOP_HOME/bin export HIVE_HOME=/u01/hive-0.11.0 export PATH=$PATH:$HADOOP_HOME/bin:$HIVE_HOME/bin (also see my sample .bash_profile) Set up ssh trust for Hadoop process, this is a mandatory step, in our case we have to establish a "local trust" as will are using a single node configuration copy the new public keys to the list of authorized keys connect and test the ssh setup to your localhost: We will run a "pseudo-Hadoop cluster", in what is called "local standalone mode", all the Hadoop java components are running in one Java process, this is enough for our demo purposes. We need to "fine tune" some Hadoop configuration files, we have to go at our $HADOOP_HOME/conf, and modify the files: core-site.xml hdfs-site.xml mapred-site.xml check that the hadoop binaries are referenced correctly from the command line by executing: hadoop -version As Hadoop is managing our "clustered HDFS" file system we have to create "the mount point" and format it , the mount point will be declared to core-site.xml as: The layout under the /u01/hadoop-1.2.1/data will be created and used by other hadoop components (MapReduce = /mapred/...) HDFS is using the /dfs/... layout structure format the HDFS hadoop file system: Start the java components for the HDFS system As an additional check, you can use the GUI Hadoop browsers to check the content of your HDFS configurations: Once our HDFS Hadoop setup is done you can use the HDFS file system to store data ( big data : )), and plug them back and forth to Oracle Databases by the means of the Big Data Connectors ( which is the next configuration step). You can create / use a Hive db, but in our case we will make a simple integration of "raw data" , through the creation of an External Table to a local Oracle instance ( on the same Linux box, we run the Hadoop HDFS one node cluster and one Oracle DB). Download some public "big data", I use the site: http://france.meteofrance.com/france/observations, from where I can get *.csv files for my big data simulations :). Here is the data layout of my example file: Download the Big Data Connector from the OTN (oraosch-2.2.0.zip), unzip it to your local file system (see picture below) Modify your environment in order to access the connector libraries , and make the following test: [oracle@dg1 bin]$./hdfs_stream Usage: hdfs_stream locationFile [oracle@dg1 bin]$ Load the data to the Hadoop hdfs file system: hadoop fs -mkdir bgtest_data hadoop fs -put obsFrance.txt bgtest_data/obsFrance.txt hadoop fs -ls /user/oracle/bgtest_data/obsFrance.txt [oracle@dg1 bg-data-raw]$ hadoop fs -ls /user/oracle/bgtest_data/obsFrance.txt Found 1 items -rw-r--r-- 1 oracle supergroup 54103 2013-10-22 06:10 /user/oracle/bgtest_data/obsFrance.txt [oracle@dg1 bg-data-raw]$hadoop fs -ls hdfs:///user/oracle/bgtest_data/obsFrance.txt Found 1 items -rw-r--r-- 1 oracle supergroup 54103 2013-10-22 06:10 /user/oracle/bgtest_data/obsFrance.txt Check the content of the HDFS with the browser UI: Start the Oracle database, and run the following script in order to create the Oracle database user, the Oracle directories for the Oracle Big Data Connector (dg1 it’s my own db id replace accordingly yours): #!/bin/bash export ORAENV_ASK=NO export ORACLE_SID=dg1 . oraenv sqlplus /nolog <<EOF CONNECT / AS sysdba; CREATE OR REPLACE DIRECTORY osch_bin_path AS '/u01/orahdfs-2.2.0/bin'; CREATE USER BGUSER IDENTIFIED BY oracle; GRANT CREATE SESSION, CREATE TABLE TO BGUSER; GRANT EXECUTE ON sys.utl_file TO BGUSER; GRANT READ, EXECUTE ON DIRECTORY osch_bin_path TO BGUSER; CREATE OR REPLACE DIRECTORY BGT_LOG_DIR as '/u01/BG_TEST/logs'; GRANT READ, WRITE ON DIRECTORY BGT_LOG_DIR to BGUSER; CREATE OR REPLACE DIRECTORY BGT_DATA_DIR as '/u01/BG_TEST/data'; GRANT READ, WRITE ON DIRECTORY BGT_DATA_DIR to BGUSER; EOF Put the following in a file named t3.sh and make it executable, hadoop jar $OSCH_HOME/jlib/orahdfs.jar \ oracle.hadoop.exttab.ExternalTable \ -D oracle.hadoop.exttab.tableName=BGTEST_DP_XTAB \ -D oracle.hadoop.exttab.defaultDirectory=BGT_DATA_DIR \ -D oracle.hadoop.exttab.dataPaths="hdfs:///user/oracle/bgtest_data/obsFrance.txt" \ -D oracle.hadoop.exttab.columnCount=7 \ -D oracle.hadoop.connection.url=jdbc:oracle:thin:@//localhost:1521/dg1 \ -D oracle.hadoop.connection.user=BGUSER \ -D oracle.hadoop.exttab.printStackTrace=true \ -createTable --noexecute then test the creation fo the external table with it: [oracle@dg1 samples]$ ./t3.sh ./t3.sh: line 2: /u01/orahdfs-2.2.0: Is a directory Oracle SQL Connector for HDFS Release 2.2.0 - Production Copyright (c) 2011, 2013, Oracle and/or its affiliates. All rights reserved. Enter Database Password:] The create table command was not executed. The following table would be created. CREATE TABLE "BGUSER"."BGTEST_DP_XTAB" ( "C1" VARCHAR2(4000), "C2" VARCHAR2(4000), "C3" VARCHAR2(4000), "C4" VARCHAR2(4000), "C5" VARCHAR2(4000), "C6" VARCHAR2(4000), "C7" VARCHAR2(4000) ) ORGANIZATION EXTERNAL ( TYPE ORACLE_LOADER DEFAULT DIRECTORY "BGT_DATA_DIR" ACCESS PARAMETERS ( RECORDS DELIMITED BY 0X'0A' CHARACTERSET AL32UTF8 STRING SIZES ARE IN CHARACTERS PREPROCESSOR "OSCH_BIN_PATH":'hdfs_stream' FIELDS TERMINATED BY 0X'2C' MISSING FIELD VALUES ARE NULL ( "C1" CHAR(4000), "C2" CHAR(4000), "C3" CHAR(4000), "C4" CHAR(4000), "C5" CHAR(4000), "C6" CHAR(4000), "C7" CHAR(4000) ) ) LOCATION ( 'osch-20131022081035-74-1' ) ) PARALLEL REJECT LIMIT UNLIMITED; The following location files would be created. osch-20131022081035-74-1 contains 1 URI, 54103 bytes 54103 hdfs://localhost:19000/user/oracle/bgtest_data/obsFrance.txt Then remove the --noexecute flag and create the external Oracle table for the Hadoop data. Check the results: The create table command succeeded. CREATE TABLE "BGUSER"."BGTEST_DP_XTAB" ( "C1" VARCHAR2(4000), "C2" VARCHAR2(4000), "C3" VARCHAR2(4000), "C4" VARCHAR2(4000), "C5" VARCHAR2(4000), "C6" VARCHAR2(4000), "C7" VARCHAR2(4000) ) ORGANIZATION EXTERNAL ( TYPE ORACLE_LOADER DEFAULT DIRECTORY "BGT_DATA_DIR" ACCESS PARAMETERS ( RECORDS DELIMITED BY 0X'0A' CHARACTERSET AL32UTF8 STRING SIZES ARE IN CHARACTERS PREPROCESSOR "OSCH_BIN_PATH":'hdfs_stream' FIELDS TERMINATED BY 0X'2C' MISSING FIELD VALUES ARE NULL ( "C1" CHAR(4000), "C2" CHAR(4000), "C3" CHAR(4000), "C4" CHAR(4000), "C5" CHAR(4000), "C6" CHAR(4000), "C7" CHAR(4000) ) ) LOCATION ( 'osch-20131022081719-3239-1' ) ) PARALLEL REJECT LIMIT UNLIMITED; The following location files were created. osch-20131022081719-3239-1 contains 1 URI, 54103 bytes 54103 hdfs://localhost:19000/user/oracle/bgtest_data/obsFrance.txt This is the view from the SQL Developer: and finally the number of lines in the oracle table, imported from our Hadoop HDFS cluster SQL select count(*) from "BGUSER"."BGTEST_DP_XTAB"; COUNT(*) ---------- 1151 In a next post we will integrate data from a Hive database, and try some ODI integrations with the ODI Big Data connector. Our simplistic approach is just a step to show you how these unstructured data world can be integrated to Oracle infrastructure. Hadoop, BigData, NoSql are great technologies, they are widely used and Oracle is offering a large integration infrastructure based on these services. Oracle University presents a complete curriculum on all the Oracle related technologies: NoSQL: Introduction to Oracle NoSQL Database Using Oracle NoSQL Database Big Data: Introduction to Big Data Oracle Big Data Essentials Oracle Big Data Overview Oracle Data Integrator: Oracle Data Integrator 12c: New Features Oracle Data Integrator 11g: Integration and Administration Oracle Data Integrator: Administration and Development Oracle Data Integrator 11g: Advanced Integration and Development Oracle Coherence 12c: Oracle Coherence 12c: New Features Oracle Coherence 12c: Share and Manage Data in Clusters Oracle Coherence 12c: Oracle GoldenGate 11g: Fundamentals for Oracle Oracle GoldenGate 11g: Fundamentals for SQL Server Oracle GoldenGate 11g Fundamentals for Oracle Oracle GoldenGate 11g Fundamentals for DB2 Oracle GoldenGate 11g Fundamentals for Teradata Oracle GoldenGate 11g Fundamentals for HP NonStop Oracle GoldenGate 11g Management Pack: Overview Oracle GoldenGate 11g Troubleshooting and Tuning Oracle GoldenGate 11g: Advanced Configuration for Oracle Other Resources: Apache Hadoop : http://hadoop.apache.org/ is the homepage for these technologies. "Hadoop Definitive Guide 3rdEdition" by Tom White is a classical lecture for people who want to know more about Hadoop , and some active "googling " will also give you some more references. About the author: Eugene Simos is based in France and joined Oracle through the BEA-Weblogic Acquisition, where he worked for the Professional Service, Support, end Education for major accounts across the EMEA Region. He worked in the banking sector, ATT, Telco companies giving him extensive experience on production environments. Eugen currently specializes in Oracle Fusion Middleware teaching an array of courses on Weblogic/Webcenter, Content,BPM /SOA/Identity-Security/GoldenGate/Virtualisation/Unified Comm Suite) throughout the EMEA region.

  Read the article

• Ingredient Substitutes while Baking

  - by Rekha

  In our normal cooking, we substitute the vegetables for the gravies we prepare. When we start baking, we look for a good recipe. At least one or two ingredient will be missing. We do not know where to substitute what to bring same output. So we finally drop the plan of baking. Again after a month, we get the interest in baking. Again one or two lack of ingredient and that’s it. We keep on doing this for months. When I was going through the cooking blogs, I came across a site with the Ingredient Substitutes for Baking: (*) is to indicate that this substitution is ideal from personal experience. Flour Substitutes ( For 1 cup of Flour) All Purpose Flour 1/2 cup white cake flour plus 1/2 cup whole wheat flour 1 cup self-rising flour (omit using salt and baking powder if the recipe calls for it since self raising flour has it already) 1 cup plus 2 tablespoons cake flour 1/2 cup (75 grams) whole wheat flour 7/8 cup (130 grams) rice flour (starch) (do not replace all of the flour with the rice flour) 7/8 cup whole wheat Bread Flour 1 cup all purpose flour 1 cup all purpose flour plus 1 teaspoon wheat gluten (*) Cake Flour Place 2 tbsp cornstarch in 1 cup and fill the rest up with All Purpose flour (*) 1 cup all purpose flour minus 2 tablespoons Pastry flour Place 2 tbsp cornstarch in 1 cup and fill the rest up with All Purpose flour Equal parts of All purpose flour plus cake flour (*) Self-rising Flour 1½ teaspoons of baking powder plus ½ teaspoon of salt plus 1 cup of all-purpose flour. Cornstarch (1 tbsp) 2 tablespoons all-purpose flour 1 tablespoon arrowroot 4 teaspoons quick-cooking tapioca 1 tablespoon potato starch or rice starch or flour Tapioca (1 tbsp) 1 – 1/2 tablespoons all-purpose flour Cornmeal (stone ground) polenta OR corn flour (gives baked goods a lighter texture) if using cornmeal for breading,crush corn chips in a blender until they have the consistency of cornmeal. maize meal Corn grits Sweeteners ( for Every 1 cup ) * * (HV) denotes Healthy Version for low fat or fat free substitution in Baking Light Brown Sugar 2 tablespoons molasses plus 1 cup of white sugar Dark Brown Sugar 3 tablespoons molasses plus 1 cup of white sugar Confectioner’s/Powdered Sugar Process 1 cup sugar plus 1 tablespoon cornstarch Corn Syrup 1 cup sugar plus 1/4 cup water 1 cup Golden Syrup 1 cup honey (may be little sweeter) 1 cup molasses Golden Syrup Combine two parts light corn syrup plus one part molasses 1/2 cup honey plus 1/2 cup corn syrup 1 cup maple syrup 1 cup corn syrup Honey 1- 1/4 cups sugar plus 1/4 cup water 3/4 cup maple syrup plus 1/2 cup granulated sugar 3/4 cup corn syrup plus 1/2 cup granulated sugar 3/4 cup light molasses plus 1/2 cup granulated white sugar 1 1/4 cups granulated white or brown sugar plus 1/4 cup additional liquid in recipe plus 1/2 teaspoon cream of tartar Maple Syrup 1 cup honey,thinned with water or fruit juice like apple 3/4 cup corn syrup plus 1/4 cup butter 1 cup Brown Rice Syrup 1 cup Brown sugar (in case of cereals) 1 cup light molasses (on pancakes, cereals etc) 1 cup granulated sugar for every 3/4 cup of maple syrup and increase liquid in the recipe by 3 tbsp for every cup of sugar.If baking soda is used, decrease the amount by 1/4 teaspoon per cup of sugar substituted, since sugar is less acidic than maple syrup Molasses 1 cup honey 1 cup dark corn syrup 1 cup maple syrup 3/4 cup brown sugar warmed and dissolved in 1/4 cup of liquid ( use this if taste of molasses is important in the baked good) Cocoa Powder (Natural, Unsweetened) 3 tablespoons (20 grams) Dutch-processed cocoa plus 1/8 teaspoon cream of tartar, lemon juice or white vinegar 1 ounce (30 grams) unsweetened chocolate (reduce fat in recipe by 1 tablespoon) 3 tablespoons (20 grams) carob powder Semisweet baking chocolate (1 oz) 1 oz unsweetened baking chocolate plus 1 Tbsp sugar Unsweetened baking chocolate (1 oz ) 3 Tbsp baking cocoa plus 1 Tbsp vegetable oil or melted shortening or margarine Semisweet chocolate chips (1 cup) 6 oz semisweet baking chocolate, chopped (Alternatively) For 1 cup of Semi sweet chocolate chips you can use : 6 tablespoons unsweetened cocoa powder, 7 tablespoons sugar ,1/4 cup fat (butter or oil) Leaveners and Diary * * (HV) denotes Healthy Version for low fat or fat free substitution in Baking Compressed Yeast (1 cake) 1 envelope or 2 teaspoons active dry yeast 1 packet (1/4 ounce) Active Dry yeast 1 cake fresh compressed yeast 1 tablespoon fast-rising active yeast Baking Powder (1 tsp) 1/3 teaspoon baking soda plus 1/2 teaspoon cream of tartar 1/2 teaspoon baking soda plus 1/2 cup buttermilk or plain yogurt 1/4 teaspoon baking soda plus 1/3 cup molasses. When using the substitutions that include liquid, reduce other liquid in recipe accordingly Baking Soda(1 tsp) 3 tsp Baking Powder ( and reduce the acidic ingredients in the recipe. Ex Instead of buttermilk add milk) 1 tsp potassium bicarbonate Ideal substitution – 2 tsp Baking powder and omit salt in recipe Cream of tartar (1 tsp) 1 teaspoon white vinegar 1 tsp lemon juice Notes from What’s Cooking America – If cream of tartar is used along with baking soda in a cake or cookie recipe, omit both and use baking powder instead. If it calls for baking soda and cream of tarter, just use baking powder.Normally, when cream of tartar is used in a cookie, it is used together with baking soda. The two of them combined work like double-acting baking powder. When substituting for cream of tartar, you must also substitute for the baking soda. If your recipe calls for baking soda and cream of tarter, just use baking powder. One teaspoon baking powder is equivalent to 1/4 teaspoon baking soda plus 5/8 teaspoon cream of tartar. If there is additional baking soda that does not fit into the equation, simply add it to the batter. Buttermilk (1 cup) 1 tablespoon lemon juice or vinegar (white or cider) plus enough milk to make 1 cup (let stand 5-10 minutes) 1 cup plain or low fat yogurt 1 cup sour cream 1 cup water plus 1/4 cup buttermilk powder 1 cup milk plus 1 1/2 – 1 3/4 teaspoons cream of tartar Plain Yogurt (1 cup) 1 cup sour cream 1 cup buttermilk 1 cup crème fraiche 1 cup heavy whipping cream (35% butterfat) plus 1 tablespoon freshly squeezed lemon juice Whole Milk (1 cup) 1 cup fat free milk plus 1 tbsp unsaturated Oil like canola (HV) 1 cup low fat milk (HV) Heavy Cream (1 cup) 3/4 cup milk plus 1/3 cup melted butter.(whipping wont work) Sour Cream (1 cup) (pls refer also Substitutes for Fats in Baking below) 7/8 cup buttermilk or sour milk plus 3 tablespoons butter. 1 cup thickened yogurt plus 1 teaspoon baking soda. 3/4 cup sour milk plus 1/3 cup butter. 3/4 cup buttermilk plus 1/3 cup butter. Cooked sauces: 1 cup yogurt plus 1 tablespoon flour plus 2 teaspoons water. Cooked sauces: 1 cup evaporated milk plus 1 tablespoon vinegar or lemon juice. Let stand 5 minutes to thicken. Dips: 1 cup yogurt (drain through a cheesecloth-lined sieve for 30 minutes in the refrigerator for a thicker texture). Dips: 1 cup cottage cheese plus 1/4 cup yogurt or buttermilk, briefly whirled in a blender. Dips: 6 ounces cream cheese plus 3 tablespoons milk,briefly whirled in a blender. Lower fat: 1 cup low-fat cottage cheese plus 1 tablespoon lemon juice plus 2 tablespoons skim milk, whipped until smooth in a blender. Lower fat: 1 can chilled evaporated milk whipped with 1 teaspoon lemon juice. 1 cup plain yogurt plus 1 tablespoon cornstarch 1 cup plain nonfat yogurt Substitutes for Fats in Baking * * (HV) denoted Healthy Version for low fat or fat free substitution in Baking Butter (1 cup) 1 cup trans-free vegetable shortening 3/4 cups of vegetable oil (example. Canola oil) Fruit purees (example- applesauce, pureed prunes, baby-food fruits). Add it along with some vegetable oil and reduce any other sweeteners needed in the recipe since fruit purees are already sweet. 1 cup polyunsaturated margarine (HV) 3/4 cup polyunsaturated oil like safflower oil (HV) 1 cup mild olive oil (not extra virgin)(HV) Note: Butter creates the flakiness and the richness which an oil/purees cant provide. If you don’t want to compromise that much to taste, replace half the butter with the substitutions. Shortening(1 cup) 1 cup polyunsaturated margarine like Earth Balance or Smart Balance(HV) 1 cup + 2tbsp Butter ( better tasting than shortening but more expensive and has cholesterol and a higher level of saturated fat; makes cookies less crunchy, bread crusts more crispy) 1 cup + 2 tbsp Margarine (better tasting than shortening but more expensive; makes cookies less crunchy, bread crusts tougher) 1 Cup – 2tbsp Lard (Has cholesterol and a higher level of saturated fat) Oil equal amount of apple sauce stiffly beaten egg whites into batter equal parts mashed banana equal parts yogurt prune puree grated raw zucchini or seeds removed if cooked. Works well in quick breads/muffins/coffee cakes and does not alter taste pumpkin puree (if the recipe can handle the taste change) Low fat cottage cheese (use only half of the required fat in the recipe). Can give rubbery texture to the end result Silken Tofu – (use only half of the required fat in the recipe). Can give rubbery texture to the end result Equal parts of fruit juice Note: Fruit purees can alter the taste of the final product is used in large quantities. Cream Cheese (1 cup) 4 tbsps. margarine plus 1 cup low-fat cottage cheese – blended. Add few teaspoons of fat-free milk if needed (HV) Heavy Cream (1 cup) 1 cup evaporated skim milk (or full fat milk) 1/2 cup low fat Yogurt plus 1/2 low fat Cottage Cheese (HV) 1/2 cup Yogurt plus 1/2 Cottage Cheese Sour Cream (1 cup) 1 cup plain yogurt (HV) 3/4 cup buttermilk or plain yogurt plus 1/3 cup melted butter 1 cup crème fraiche 1 tablespoon lemon juice or vinegar plus enough whole milk to fill 1 cup (let stand 5-10 minutes) 1/2 cup low-fat cottage cheese plus 1/2 cup low-fat or nonfat yogurt (HV) 1 cup fat-free sour cream (HV) Note: How to Make Maple Syrup Substitute at home For 1 Cup Maple Syrup 1/2 cup granulated sugar 1 cup brown sugar, firmly packed 1 cup boiling water 1 teaspoon butter 1 teaspoon maple extract or vanilla extract Method In a heavy saucepan, place the granulated sugar and keep stirring until it melts and turns slightly brown. Alternatively in another pan, place brown sugar and water and bring to a boil without stirring. Now mix both the sugars and simmer in low heat until they come together as one thick syrup. Remove from heat, add butter and the extract. Use this in place of maple syrup. Store it in a fridge in an air tight container. Even though this was posted in their site long back, I found it helpful. So posting it for you. via chefinyou . cc image credit: flickr/zetrules

  Read the article

• CodePlex Daily Summary for Monday, April 19, 2010

  CodePlex Daily Summary for Monday, April 19, 2010New Projects8085 Microprocessor simulator: This program allows you to write 8085 programs in assembly and run those programs on your PC. It comes with lots of help, plus you can put breakpo...Additional.NET framework: The Additional.Net framework extends the functionality of the .NET framework for easier application development. It is developed in C#.Astoria Contrib: A contrib project for filling the gaps in WCF Data Services, providing missing functionality or augmenting with T4 templates, helpers, etc.ClipoWeb: ClipoWeb is a web clipboard that allows you to copy text and files between computers. Users access a web page on the source and destination compute...elearning Center: Đây là một ứng dụng web viết hoàn toàn bằng Sliverlight. Ứng dụng này là một dạng elearning với đầy đủ chức năng và có khả năng tương tác tối đa v...Excel VSTO SQL Server Browser: Get Data from SQL Server and put it in Excel directly. The objective is to get more control about what do you need to pull and create automatic pro...Generic Tree Structure: Generic Base Classes that helps you to create complex tree structures without writing it again and again. Simply to use Like "var Node<Folder> fold...LAN Lordz LAN Party System: The LAN Lordz LAN Party System makes it easier for medium and large size events to track their attendance, sponsors, door prizes, tournaments, and...LiteFx: O LiteFx é um framework que ajuda na implementação de DDD (anêmico ou rico) ele foi desenvolvido por Douglas Aguiar (http://twitter.com/DouglasAgui...Managed UI Flow for ASP.NET MVC Framework: If your web application getting more complex, understanding and managing of complex UI flows(pageflow of application) getting harder and harder, If...Meus Exemplos: Meus ExemplosOrchard Blueprint Theme: Orchard BluePrint is a project that provides a WYSIWYG reference implementation of a Orchard theme to help designers get started with theme design....Outlook Social Network Connector - Avatar: Avatar 是一个开源的MS Outlook的插件，豆瓣用户可以在Outlook 2010中使用豆瓣。查看一封邮件中相关的收件人、发件人的用户广播、同城活动以及豆邮。不用上豆瓣也能方便了解好友动态。这个插件使用C#， .NET 4.0 开发。API 请求认证使用OAuth 认证。 (Avat...Quadro Tree: This is Quadri tree library.Sharepoint 2010 Alert Controller: In MOSS 2007 or Sharepoint Server 2010 if you want to see your alerts by list name you should use this tool.SharePoint Web Parts: The goal of this project is to develop a set of web parts for SharePoint.Silverlight Image Cropper: This is a silverlight 4 util that makes it easy to crop out a number images of a specific resolution screen or screens. ie. an easy way to crop ...SilverlightFTP: Silverlight ftp clientsplibex: libraries for sharepoint lists manipulationStardustExtensions: Official Extensions for StardustSwim Team Manager: Swim Team Manager is designed for managing and tracking administrative and performance information for your club, school, or swim team. Swim Tea...ToDoListWpf: A To Do List, I used it to manage my work items. I am sorry for my poor English.Trance Layer: TranceLayer is a fast and flexible logging or diagnostics framework for .Net. It allows you to plug it into an existing or new application with m...Unoficcial NeoFM.hu NowPlaying: A little windows tray program. Shows what's on neofm.hu right now.WabbitStudio Z80 Software Tools: The software suite provides all of the tools you need to create high quality Z80 software in Z80 assembly language, with a focus on TI calculators....WinToolbar: Windows.Toolbar is Silverlight library that implements common widgets that allows us to build a rich toolbar control in our applications, it incor...XP-More: XP-More is a tool that helps manage Windows 7 Virtual Machines (XP Mode and any other). Specifically, it makes duplication of VMs a no brainer - no...Yodelay .NET Framework Extensions: The Yodelay .NET Framework Extensions project provides a library of components that make many kinds of programming tasks simpler. These include bas...New ReleasesClipoWeb: ClipoWeb 1.0: First Beta release of the ClipoWeb web applicationDDDSample.Net: 0.8: This release contains all four versions of DDDSample.Net available in previous, 0.7 and a brand new one: Layered Model version. Layered Model demon...DotNetNuke Blueprint: 00.00.02: Added to this version CSS Reset Skin version including Grids This version will soon be updated with corresponding HTML version and DNN templateEsferatec.Text.RegularExpressions: 3.5.1003.1001: first stable release of the class; the assembly file is ready to use, the documentation is complete;Excel VSTO SQL Server Browser: Sample Only: Sample without Ribbon UI, if you close the TaskPane you will no longer able to open it without restart ExcelFolder Bookmarks: Folder Bookmarks 1.5.5: This is the latest version of Folder Bookmarks (1.5.5), with the new Archive Manager and Archive Viewer. It has an installer - it will create a dir...Gardens Point LEX: Gardens Point LEX, Version 1.1.3: The main distribution is a zip file. This contains the binary executable, documentation, source code and the examples. ChangesVersion 1.1.3 corre...Gardens Point Parser Generator: Gardens Point Parser Generator V1.4.0: The distribution is a zip archive which contains the binary executables, documentation, source code and examples. ChangesVersion 1.4.0 of GPPG has...HKGolden Express: HKGoldenExpress (Build 201004181455): New features: Added rating of each topic. (Note: This feature is availabe since Build 201004172120) Bug fix: Handle invalid XML character in XML...Home Access Plus+: v4.0.0.0 Beta: v4.0.0.0 Beta Change Log: Moved to using .net 4.0 New Silverlight Uploader Various .net 4 fixes and tweaks File Changes: All fixes have changedHTML Ruby: 6.21.6: Reduced performance hit on pages with heavy DOM manipulations Fixed issue where empty tags caused it to apply invalid spacing values Stop spaci...LINQ to VFP: LinqToVfp (v1.0.17.2): Modified to allow using RecNo as a primary key. This build requires IQToolkit v0.17b.Managed UI Flow for ASP.NET MVC Framework: Preview 1: The source available on this site, does not reflect the final state of the project, it is a preview of what will be shipping in the framework in th...MVVM Light Toolkit: MVVM Light Toolkit V3 SP1 (2): Super minor update to accommodate the new Blend 4 RC. Only changes: The path to the Blend 4 templates changed to be "My Documents\Expression\Blend...N2 CMS: 2.0 rc: N2 is a lightweight CMS framework for ASP.NET. It helps you build great web sites that anyone can update. Major Changes (1.5 -> 2.0 release candid...OpenGL ES 2.0 Compact Framework Wrapper: Sample application CAB with texturing: This took some time as it was pretty hard to get the texture loaded and setup so that it would bind to the sampler2D in the fragment shader. Featu...Orchard Blueprint Theme: 00.00.01: This is the first release of this project, still in a very alpha version. Very soon this release is to be updated with the HTML version of the them...RoughJs: RoughJsSL: This is Silverlight library's CompilerSharepoint 2010 Alert Controller: Sharepoint 2010 Alert Controller: After you download WSP file you can get help from Home PageSharePoint LogViewer: SharePoint LogViewer 2.5: Minimize log viewer to tray Get popup notification of SharePoint log events from tray Redirect log entries to event log Send email notifications on...Site Directory for SharePoint 2010 (from Microsoft Consulting Services, UK): v1.1: This is a minor update which includes the following changes: Code consolidation across the whole project Additional site data captured. See solut...Stardust: Stardust 1.0: First stable version of Stardust (Build 172)StardustExtensions: Facebook Extension: Extension for stardust to upload and post images on Facebook.StardustExtensions: Facebook Extension (Source): The source code of an extension for Stardust used to post images on facebook.StardustExtensions: WPF Example: This is an example extension. Uses WPF to create a Window and say "Hello World!" Is a perfect download if want to start writing Stardust ExtensionsStardustExtensions: WPF Example Source: This is the source code of an extension that creates a Window using WPF & displays a simple text. Is great as an example of creating Stardust Exten...TFTP Server: TFTP Server 1.1 Beta installer: New MSI based installer Installs a TFTP service Supports multiple servers on different endpoints, with every server pointing to its own root di...TiledLib: TiledLib 1.1: This download is for prebuilt DLLs and a demo project. For the full source code, use the Source Code tab. Changes: Bug fixes in a few methods Ad...Trance Layer: TranceLayer Digger: Digger version is a beta. It is intended to be used as a demonstration of muscles while lacking a set of features that are in the docs. The set of ...uManage - Active Directory Self-Service Portal: uManage v1.2 (.NET 4.0 RTM): New Releasev1.2 Adds the Administrative Portal as well as the requirement of a MSSQL database (2005+). The Setup Wizard has also been updated to i...Unoficcial NeoFM.hu NowPlaying: NeoNotifier: First release. Aplha, but usable.VidCoder: 0.2.1: Changes: Added 2-pass encoding Fixed x264 options getting mangled during p-invoke Fixed intermittent crash with logging window open due to thre...WCF RIA Services Contrib: WCF RIA Services Contrib RC2 Release: This version is for the WCF RIA Services RC2 (SL4 RTM) release. The ApplyState has been modifed in this version to disable validation during proces...WiiCIS.NET: WiiCIS.NET v0.2: Changes... - Removal of WiimoteManager, connection must be done manually - Accelerometer orientation was originally in degrees, is now in radians -...WinToolbar: WinToolbar Source code plus sample: This zip file contains the current version source code and libraries plus a testrunner (sample app).XP-More: 0.9 (Beta): Most of the functionality is in place, final polishing will be done soon.Most Popular ProjectsFacebook Developer ToolkitWSPBuilder (SharePoint WSP tool)QuickGraph, Graph Data Structures And Algorithms for .NetPerformance Analysis of Logs (PAL) Toolpatterns & practices: Team Development with Visual Studio Team Foundation ServerTFS Integration Platformpatterns & practices: Performance Testing Guidance for Web Applicationspatterns & practices: Enterprise Library ContribJSON ViewerManaged Wifi APIMost Active ProjectsRawrpatterns & practices – Enterprise LibraryIndustrial DashboardIonics Isapi Rewrite FilterFarseer Physics EngineMVVM Light ToolkitjQuery Library for SharePoint Web ServicesN2 CMSCaliburn: An Application Framework for WPF and SilverlightBlogEngine.NET

  Read the article

• The Internet of Things & Commerce: Part 2 -- Interview with Brian Celenza, Commerce Innovation Strategist

  - by Katrina Gosek, Director | Commerce Product Strategy-Oracle

  Internet of Things & Commerce Series: Part 2 (of 3) Welcome back to the second installation of my three part series on the Internet of Things & Commerce. A few weeks ago, I wrote “The Next 7,000 Days” about how we’ve become embedded in a digital architecture in the last 7,000 days since the birth of the internet – an architecture that everyday ties the massive expanse of the internet evermore closely with our physical lives. This blog series explores how this new blend of virtual and material will change how we shop and how businesses sell. Now enjoy reading my interview with Brian Celenza, one of the chief strategists in our Oracle Commerce innovation group. He comments on the past, present, and future of the how the growing Internet of Things relates and will relate to the buying and selling of goods on and offline. -------------------------------------------- QUESTION: You probably have one of the coolest jobs on our team, Brian – and frankly, one of the coolest jobs in our industry. As part of the innovation team for Oracle Commerce, you’re regularly working on bold features and groundbreaking commerce-focused experiences for our vision demos. As you look back over the past couple of years, what is the biggest trend (or trends) you’ve seen in digital commerce that started to bring us closer to this idea of what people are calling an “Internet of Things”? Brian: Well as you look back over the last couple of years, the speed at which change in our industry has moved looks like one of those blurred movement photos – you know the ones where the landscape blurs because the observer is moving so quickly your eye focus can’t keep up. But one thing that is absolutely clear is that the biggest catalyst for that speed of change – especially over the last three years – has been mobile. Mobile technology changed everything. Over the last three years the entire thought process of how to sell on (and offline) has shifted because of mobile technology advances. Particularly for eCommerce professionals who have started to move past the notion of “channels” for selling goods to this notion of “Mobile First”… then the Web site. Or more accurately, that everything – smartphones, web, store, tablet – is just one channel or has to act like one singular access point to the same product catalog, information and content. The most innovative eCommerce professionals realized some time ago that it’s not ideal to build an eCommerce Web site and then build everything on top of or off of it. Rather, they want to build an eCommerce API and then integrate it will all other systems. To accomplish this, they are leveraging all the latest mobile technologies or possibilities mobile technology has opened up: 4G and LTE, GPS, bluetooth, touch screens, apps, html5… How has this all started to come together for shopping experiences on and offline? Well to give you a personal example, I remember visiting an Apple store a few years ago and being amazed that I didn’t have to wait in line because a store associate knew everything about me from my ID – right there on the sales floor – and could check me out anywhere. Then just a few months later (when like any good addict) I went back to get the latest and greatest new gadget, I felt like I was stealing it because I could check myself out with my smartphone. I didn’t even need to see a sales associate OR go to a cash register. Amazing. And since then, all sort sorts of companies across all different types of industries – from food service to apparel –  are starting to see mobile payments in the billions of dollars now thanks not only to the convenience factor but to smart loyalty rewards programs as well. These are just some really simple current examples that come to mind. So many different things have happened in the last couple of years, it’s hard to really absorb all of the quickly – because as soon as you do, everything changes again! Just like that blurry speed photo image. For eCommerce, however, this type of new environment underscores the importance of building an eCommerce API – a platform that has services you can tap in to and build on as the landscape changes at a fever pitch. It’s a mobile first perspective. A web service perspective – particularly if you are thinking of how to engage customers across digital and physical spaces. —— QUESTION: Thanks for bringing us into the present – some really great examples you gave there to put things into perspective. So what do you see as the biggest trend right now around the “Internet of Things” – and what’s coming next few years? Brian: Honestly, even sitting where I am in the innovation group – it’s hard to look out even 12 months because, well, I don’t even think we’ve fully caught up with what is possible now. But I can definitely say that in the last 12 months and in the coming 12 months, in the technology and eCommerce world it’s all about iBeacons. iBeacons are awesome tools we have right now to tie together physical and digital shopping experiences. They know exactly where you are as a shopper and can communicate that to businesses. Currently there seem to be two camps of thought around iBeacons. First, many people are thinking of them like an “indoor GPS”, which to be fair they literally are. The use case this first camp envisions for iBeacons is primarily for advertising and marketing. So they use iBeacons to push location-based promotions to customers if they are close to a store or in a store. You may have seen these types of mobile promotions start to pop up occasionally on your smart phone as you pass by a store you’ve bought from in the past. That’s the work of iBeacons. But in my humble opinion, these promotions probably come too early in the customer journey and although they may be well timed and work to “convert” in some cases, I imagine in most they are just eroding customer trust because they are kind of a “one-size-fits-all” solution rather than one that is taking into account what exactly the customer might be looking for in that particular moment. Maybe they just want more information and a promotion is way too soon for that type of customer. The second camp is more in line with where my thinking falls. In this case, businesses take a more sensitive approach with iBeacons to customers’ needs. Instead of throwing out a “one-size-fits-all” to any passer by with iBeacons, the use case is more around looking at the physical proximity of a customer as an opportunity to provide a service: show expert reviews on a product they may be looking at in a particular aisle of a store, offer the opportunity to compare prices (and then offer a promotion), signal an in-store associate if a customer has been in the store for more than 10 minutes in one place. These are all less intrusive more value-driven uses of iBeacons. And they are more about building customer trust through service. To take this example a bit further into the future realm of “Big Data” and “Internet of Things” businesses could actually use the Oracle Commerce Platform and iBeacons to “silently” track customer movement w/in the store to provide higher quality service. And this doesn’t have to be creepy or intrusive. Simply if a customer has been in a particular department or aisle for more than a 5 or 10 minutes, an in-store associate could come over an offer some assistance already knowing customer preferences from their online profile and maybe even seeing the items in a shopping cart they started at home. None of this has to be revealed to the customer, but it certainly could boost the level of service an in-store sales associate could provide. Or, in another futuristic example, stores could use the digital footprint of the physical store transmitted by iBeacons to generate heat maps of the store that could be tracked over time. Imagine how much you could find out about which parts of the store are more busy during certain parts of the day or seasons. This could completely revolutionize how physical merchandising is deployed or where certain high value / new items are placed. And / or this use of iBeacons could also help businesses figure out if customers are getting held up in certain parts of the store during busy days like Black Friday. If long lines are causing customers to bounce from a physical store and leave those holiday gifts behind, maybe having employees with mobile check as an option could remove the cash register bottleneck. But going to back to my original statement, it’s all still very early in the story for iBeacons. The hardware manufacturers are still very new and there is still not one clear standard.  Honestly, it all goes back to building and maintaining an extensible and flexible platform for anywhere engagement. What you’re building today should allow you to rapidly take advantage of whatever unimaginable use cases wait around the corner. ------------------------------------------------------ I hope you enjoyed the brief interview with Brian. It’s really awesome to have such smart and innovation-minded individuals on our Oracle Commerce innovation team. Please join me again in a few weeks for Part 3 of this series where I interview one of the product managers on our team about how the blending of digital and in-store selling in influencing our product development and vision.

  Read the article

• How to solve "403 Forbidden" on CentOS6 with SELinux Disabled?

  - by André

  I have a machine on Linode that is driving me crazy. Linode does not have SELinux on CentOS6... I'm trying to configure to put my website in "/home/websites/public_html/mysite.com/public" As I don´t have SELinux enable, how can I avoid the "403 Forbidden" that I get when trying to access the webpage? Sorry for my english. Best Regards, Update1, ERROR_LOG [Mon Oct 17 14:04:16 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:08:07 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:10:25 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:10:41 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:32:35 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 14:34:45 2011] [error] [client 58.218.199.227] (13)Permission denied: access to /proxy-1.php denied [Mon Oct 17 15:32:25 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:37:26 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:37:43 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:38:32 2011] [error] [client 127.0.0.1] (13)Permission denied: access to / denied [Mon Oct 17 15:42:56 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable [Mon Oct 17 15:43:12 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable [Mon Oct 17 15:45:34 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable [Mon Oct 17 15:51:25 2011] [crit] [client 127.0.0.1] (13)Permission denied: /home/websites/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable Upadate2, /home/websites directory drwx------ 3 websites websites 4096 Oct 17 14:52 . drwxr-xr-x. 3 root root 4096 Oct 17 13:42 .. -rw------- 1 websites websites 372 Oct 17 14:52 .bash_history -rw-r--r-- 1 websites websites 18 May 30 11:46 .bash_logout -rw-r--r-- 1 websites websites 176 May 30 11:46 .bash_profile -rw-r--r-- 1 websites websites 124 May 30 11:46 .bashrc drwxrwxr-x 3 websites apache 4096 Oct 17 13:45 public_html Update3, httpd.conf ### Section 1: Global Environment ServerTokens OS ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 60 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 15 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 4 MaxClients 300 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> #Listen 12.34.56.78:80 Listen 80 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule status_module modules/mod_status.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule info_module modules/mod_info.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule userdir_module modules/mod_userdir.so LoadModule alias_module modules/mod_alias.so LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_ajp_module modules/mod_proxy_ajp.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so Include conf.d/*.conf #ExtendedStatus On User apache Group apache ServerAdmin root@localhost #ServerName www.example.com:80 UseCanonicalName Off DocumentRoot "/var/www/html" # # Each directory to which Apache has access can be configured with respect # to which services and features are allowed and/or disabled in that # directory (and its subdirectories). # # First, we configure the "default" to be a very restrictive set of # features. # <Directory /> Options FollowSymLinks AllowOverride None </Directory> # # Note that from this point forward you must specifically allow # particular features to be enabled - so if something's not working as # you might expect, make sure that you have specifically enabled it # below. # # # This should be changed to whatever you set DocumentRoot to. # <Directory "/home/websites/public_html"> # # Possible values for the Options directive are "None", "All", # or any combination of: # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews # # Note that "MultiViews" must be named *explicitly* --- "Options All" # doesn't give it to you. # # The Options directive is both complicated and important. Please see # http://httpd.apache.org/docs/2.2/mod/core.html#options # for more information. # Options Indexes FollowSymLinks # # AllowOverride controls what directives may be placed in .htaccess files. # It can be "All", "None", or any combination of the keywords: # Options FileInfo AuthConfig Limit # AllowOverride None # # Controls who can get stuff from this server. # Order allow,deny Allow from all </Directory> # # UserDir: The name of the directory that is appended onto a user's home # directory if a ~user request is received. # # The path to the end user account 'public_html' directory must be # accessible to the webserver userid. This usually means that ~userid # must have permissions of 711, ~userid/public_html must have permissions # of 755, and documents contained therein must be world-readable. # Otherwise, the client will only receive a "403 Forbidden" message. # # See also: http://httpd.apache.org/docs/misc/FAQ.html#forbidden # <IfModule mod_userdir.c> # # UserDir is disabled by default since it can confirm the presence # of a username on the system (depending on home directory # permissions). # UserDir disabled # # To enable requests to /~user/ to serve the user's public_html # directory, remove the "UserDir disabled" line above, and uncomment # the following line instead: # #UserDir public_html </IfModule> # # Control access to UserDir directories. The following is an example # for a site where these directories are restricted to read-only. # #<Directory /home/*/public_html> # AllowOverride FileInfo AuthConfig Limit # Options MultiViews Indexes SymLinksIfOwnerMatch IncludesNoExec # <Limit GET POST OPTIONS> # Order allow,deny # Allow from all # </Limit> # <LimitExcept GET POST OPTIONS> # Order deny,allow # Deny from all # </LimitExcept> #</Directory> # # DirectoryIndex: sets the file that Apache will serve if a directory # is requested. # # The index.html.var file (a type-map) is used to deliver content- # negotiated documents. The MultiViews Option can be used for the # same purpose, but it is much slower. # DirectoryIndex index.html index.html.var # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy All </Files> # # TypesConfig describes where the mime.types file (or equivalent) is # to be found. # TypesConfig /etc/mime.types # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # The mod_mime_magic module allows the server to use various hints from the # contents of the file itself to determine its type. The MIMEMagicFile # directive tells the module where the hint definitions are located. # <IfModule mod_mime_magic.c> # MIMEMagicFile /usr/share/magic.mime MIMEMagicFile conf/magic </IfModule> # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off #EnableMMAP off #EnableSendfile off # # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog logs/error_log LogLevel warn # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # "combinedio" includes actual counts of actual bytes received (%I) and sent (%O); this # requires the mod_logio module to be loaded. #LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio # # The location and format of the access logfile (Common Logfile Format). # If you do not define any access logfiles within a <VirtualHost> # container, they will be logged here. Contrariwise, if you *do* # define per-<VirtualHost> access logfiles, transactions will be # logged therein and *not* in this file. # #CustomLog logs/access_log common # # If you would like to have separate agent and referer logfiles, uncomment # the following directives. # #CustomLog logs/referer_log referer #CustomLog logs/agent_log agent # # For a single logfile with access, agent, and referer information # (Combined Logfile Format), use the following directive: # CustomLog logs/access_log combined ServerSignature On Alias /icons/ "/var/www/icons/" <Directory "/var/www/icons"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> # # WebDAV module configuration section. # <IfModule mod_dav_fs.c> # Location of the WebDAV lock database. DAVLockDB /var/lib/dav/lockdb </IfModule> # # ScriptAlias: This controls which directories contain server scripts. # ScriptAliases are essentially the same as Aliases, except that # documents in the realname directory are treated as applications and # run by the server when requested rather than as documents sent to the client. # The same rules about trailing "/" apply to ScriptAlias directives as to # Alias. # ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" # # "/var/www/cgi-bin" should be changed to whatever your ScriptAliased # CGI directory exists, if you have that configured. # <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable Charset=UTF-8 AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ # # DefaultIcon is which icon to show for files which do not have an icon # explicitly set. # DefaultIcon /icons/unknown.gif # # AddDescription allows you to place a short description after a file in # server-generated indexes. These are only displayed for FancyIndexed # directories. # Format: AddDescription "description" filename # #AddDescription "GZIP compressed document" .gz #AddDescription "tar archive" .tar #AddDescription "GZIP compressed tar archive" .tgz # # ReadmeName is the name of the README file the server will look for by # default, and append to directory listings. # # HeaderName is the name of a file which should be prepended to # directory indexes. ReadmeName README.html HeaderName HEADER.html # # IndexIgnore is a set of filenames which directory indexing should ignore # and not include in the listing. Shell-style wildcarding is permitted. # IndexIgnore .??* *~ *# HEADER* README* RCS CVS *,v *,t # # DefaultLanguage and AddLanguage allows you to specify the language of # a document. You can then use content negotiation to give a browser a # file in a language the user can understand. # # Specify a default language. This means that all data # going out without a specific language tag (see below) will # be marked with this one. You probably do NOT want to set # this unless you are sure it is correct for all cases. # # * It is generally better to not mark a page as # * being a certain language than marking it with the wrong # * language! # # DefaultLanguage nl # # Note 1: The suffix does not have to be the same as the language # keyword --- those with documents in Polish (whose net-standard # language code is pl) may wish to use "AddLanguage pl .po" to # avoid the ambiguity with the common suffix for perl scripts. # # Note 2: The example entries below illustrate that in some cases # the two character 'Language' abbreviation is not identical to # the two character 'Country' code for its country, # E.g. 'Danmark/dk' versus 'Danish/da'. # # Note 3: In the case of 'ltz' we violate the RFC by using a three char # specifier. There is 'work in progress' to fix this and get # the reference data for rfc1766 cleaned up. # # Catalan (ca) - Croatian (hr) - Czech (cs) - Danish (da) - Dutch (nl) # English (en) - Esperanto (eo) - Estonian (et) - French (fr) - German (de) # Greek-Modern (el) - Hebrew (he) - Italian (it) - Japanese (ja) # Korean (ko) - Luxembourgeois* (ltz) - Norwegian Nynorsk (nn) # Norwegian (no) - Polish (pl) - Portugese (pt) # Brazilian Portuguese (pt-BR) - Russian (ru) - Swedish (sv) # Simplified Chinese (zh-CN) - Spanish (es) - Traditional Chinese (zh-TW) # AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw # # LanguagePriority allows you to give precedence to some languages # in case of a tie during content negotiation. # # Just list the languages in decreasing order of preference. We have # more or less alphabetized them here. You probably want to change this. # LanguagePriority en ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv zh-CN zh-TW # # ForceLanguagePriority allows you to serve a result page rather than # MULTIPLE CHOICES (Prefer) [in case of a tie] or NOT ACCEPTABLE (Fallback) # [in case no accepted languages matched the available variants] # ForceLanguagePriority Prefer Fallback # # Specify a default charset for all content served; this enables # interpretation of all content as UTF-8 by default. To use the # default browser choice (ISO-8859-1), or to allow the META tags # in HTML content to override this choice, comment out this # directive: # AddDefaultCharset UTF-8 # # AddType allows you to add to or override the MIME configuration # file mime.types for specific file types. # #AddType application/x-tar .tgz # # AddEncoding allows you to have certain browsers uncompress # information on the fly. Note: Not all browsers support this. # Despite the name similarity, the following Add* directives have nothing # to do with the FancyIndexing customization directives above. # #AddEncoding x-compress .Z #AddEncoding x-gzip .gz .tgz # If the AddEncoding directives above are commented-out, then you # probably should define those extensions to indicate media types: # AddType application/x-compress .Z AddType application/x-gzip .gz .tgz # # MIME-types for downloading Certificates and CRLs # AddType application/x-x509-ca-cert .crt AddType application/x-pkcs7-crl .crl # # AddHandler allows you to map certain file extensions to "handlers": # actions unrelated to filetype. These can be either built into the server # or added with the Action directive (see below) # # To use CGI scripts outside of ScriptAliased directories: # (You will also need to add "ExecCGI" to the "Options" directive.) # #AddHandler cgi-script .cgi # # For files that include their own HTTP headers: # #AddHandler send-as-is asis # # For type maps (negotiated resources): # (This is enabled by default to allow the Apache "It Worked" page # to be distributed in multiple languages.) # AddHandler type-map var # # Filters allow you to process content before it is sent to the client. # # To parse .shtml files for server-side includes (SSI): # (You will also need to add "Includes" to the "Options" directive.) # AddType text/html .shtml AddOutputFilter INCLUDES .shtml # # Action lets you define media types that will execute a script whenever # a matching file is called. This eliminates the need for repeated URL # pathnames for oft-used CGI file processors. # Format: Action media/type /cgi-script/location # Format: Action handler-name /cgi-script/location # # # Customizable error responses come in three flavors: # 1) plain text 2) local redirects 3) external redirects # # Some examples: #ErrorDocument 500 "The server made a boo boo." #ErrorDocument 404 /missing.html #ErrorDocument 404 "/cgi-bin/missing_handler.pl" #ErrorDocument 402 http://www.example.com/subscription_info.html # # # Putting this all together, we can internationalize error responses. # # We use Alias to redirect any /error/HTTP_<error>.html.var response to # our collection of by-error message multi-language collections. We use # includes to substitute the appropriate text. # # You can modify the messages' appearance without changing any of the # default HTTP_<error>.html.var files by adding the line: # # Alias /error/include/ "/your/include/path/" # # which allows you to create your own set of files by starting with the # /var/www/error/include/ files and # copying them to /your/include/path/, even on a per-VirtualHost basis. # Alias /error/ "/var/www/error/" <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> # ErrorDocument 400 /error/HTTP_BAD_REQUEST.html.var # ErrorDocument 401 /error/HTTP_UNAUTHORIZED.html.var # ErrorDocument 403 /error/HTTP_FORBIDDEN.html.var # ErrorDocument 404 /error/HTTP_NOT_FOUND.html.var # ErrorDocument 405 /error/HTTP_METHOD_NOT_ALLOWED.html.var # ErrorDocument 408 /error/HTTP_REQUEST_TIME_OUT.html.var # ErrorDocument 410 /error/HTTP_GONE.html.var # ErrorDocument 411 /error/HTTP_LENGTH_REQUIRED.html.var # ErrorDocument 412 /error/HTTP_PRECONDITION_FAILED.html.var # ErrorDocument 413 /error/HTTP_REQUEST_ENTITY_TOO_LARGE.html.var # ErrorDocument 414 /error/HTTP_REQUEST_URI_TOO_LARGE.html.var # ErrorDocument 415 /error/HTTP_UNSUPPORTED_MEDIA_TYPE.html.var # ErrorDocument 500 /error/HTTP_INTERNAL_SERVER_ERROR.html.var # ErrorDocument 501 /error/HTTP_NOT_IMPLEMENTED.html.var # ErrorDocument 502 /error/HTTP_BAD_GATEWAY.html.var # ErrorDocument 503 /error/HTTP_SERVICE_UNAVAILABLE.html.var # ErrorDocument 506 /error/HTTP_VARIANT_ALSO_VARIES.html.var </IfModule> </IfModule> # # The following directives modify normal HTTP response behavior to # handle known problems with browser implementations. # BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4\.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4\.0" force-response-1.0 BrowserMatch "Java/1\.0" force-response-1.0 BrowserMatch "JDK/1\.0" force-response-1.0 # # The following directive disables redirects on non-GET requests for # a directory that does not include the trailing slash. This fixes a # problem with Microsoft WebFolders which does not appropriately handle # redirects for folders with DAV methods. # Same deal with Apple's DAV filesystem and Gnome VFS support for DAV. # BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully # # Allow server status reports generated by mod_status, # with the URL of http://servername/server-status # Change the ".example.com" to match your domain to enable. # #<Location /server-status> # SetHandler server-status # Order deny,allow # Deny from all # Allow from .example.com #</Location> # # Allow remote server configuration reports, with the URL of # http://servername/server-info (requires that mod_info.c be loaded). # Change the ".example.com" to match your domain to enable. # #<Location /server-info> # SetHandler server-info # Order deny,allow # Deny from all # Allow from .example.com #</Location> # # Proxy Server directives. Uncomment the following lines to # enable the proxy server: # #<IfModule mod_proxy.c> #ProxyRequests On # #<Proxy *> # Order deny,allow # Deny from all # Allow from .example.com #</Proxy> # # Enable/disable the handling of HTTP/1.1 "Via:" headers. # ("Full" adds the server version; "Block" removes all outgoing Via: headers) # Set to one of: Off | On | Full | Block # #ProxyVia On # # To enable a cache of proxied content, uncomment the following lines. # See http://httpd.apache.org/docs/2.2/mod/mod_cache.html for more details. # #<IfModule mod_disk_cache.c> # CacheEnable disk / # CacheRoot "/var/cache/mod_proxy" #</IfModule> # #</IfModule> # End of proxy directives. ### Section 3: Virtual Hosts # # VirtualHost: If you want to maintain multiple domains/hostnames on your # machine you can setup VirtualHost containers for them. Most configurations # use only name-based virtual hosts so the server doesn't need to worry about # IP addresses. This is indicated by the asterisks in the directives below. # # Please see the documentation at # <URL:http://httpd.apache.org/docs/2.2/vhosts/> # for further details before you try to setup virtual hosts. # # You may use the command line option '-S' to verify your virtual host # configuration. # # Use name-based virtual hosting. # NameVirtualHost *:80 # # NOTE: NameVirtualHost cannot be used without a port specifier # (e.g. :80) if mod_ssl is being used, due to the nature of the # SSL protocol. # # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for requests without a known # server name. # #<VirtualHost *:80> # ServerAdmin [email protected] # DocumentRoot /www/docs/dummy-host.example.com # ServerName dummy-host.example.com # ErrorLog logs/dummy-host.example.com-error_log # CustomLog logs/dummy-host.example.com-access_log common #</VirtualHost> # domain: mysite.com # public: /home/websites/public_html/mysite.com/ <VirtualHost *:80> # Admin email, Server Name (domain name) and any aliases ServerAdmin [email protected] ServerName mysite.com ServerAlias www.mysite.com # Index file and Document Root (where the public files are located) DirectoryIndex index.html DocumentRoot /home/websites/public_html/mysite.com/public # Custom log file locations LogLevel warn ErrorLog /home/websites/public_html/mysite.com/log/error.log CustomLog /home/websites/public_html/mysite.com/log/access.log combined </VirtualHost>

  Read the article

• CodePlex Daily Summary for Wednesday, February 23, 2011

  CodePlex Daily Summary for Wednesday, February 23, 2011Popular ReleasesSQL Server CLR Function for Address Correction and Geocoding: Release 2.1: Adds support for the User Key argument in Process function calls.ClosedXML - The easy way to OpenXML: ClosedXML 0.45.2: New on this release: 1) Added data validation. See Data Validation 2) Deleting or clearing cells deletes the hyperlinks too. New on v0.45.1 1) Fixed issues 6237, 6240 New on v0.45.2 1) Fixed issues 6257, 6266 New Examples Data ValidationCrystalbyte Equinox (LINQ to IMAP): Equinox Alpha Release v0.3.0.0: Fixed bugsFixed issue introduced in last release; No connection could be established since the client did not read the welcome message during the initial connection attempt. Contact names are now being properly parsed into the envelope Introduced featuresImplemented SMTP support, the client is contained inside the Crystalbyte.Equinox.Smtp.dll which was added to the current release.OMEGA CMS: OMEGA CMA - Alpha 0.2: A few fixes for OMEGA Framework (DLL) A few tweeks for OMEGA CMSJSLint for Visual Studio 2010: 1.2.4: Bug Fix release.Coding4Fun Tools: Coding4Fun.Phone.Toolkit v1.2: New control, Toast Prompt! Removed progress bar since Silverlight Toolkit Feb 2010 has it.Umbraco CMS: Umbraco 4.7: Service release fixing 31 issues. A full changelog will be available with the final stable release of 4.7 Important when upgradingUpgrade as if it was a patch release (update /bin, /umbraco and /umbraco_client). For general upgrade information follow the guide found at http://our.umbraco.org/wiki/install-and-setup/upgrading-an-umbraco-installation 4.7 requires the .NET 4.0 framework Web.Config changes Update the web web.config to include the 4 changes found in (they're clearly marked in...HubbleDotNet - Open source full-text search engine: V1.1.0.0: Add Sqlite3 DBAdapter Add App Report when Query Cache is Collecting. Improve the performance of index through Synchronize. Add top 0 feature so that we can only get count of the result. Improve the score calculating algorithm of match. Let the score of the record that match all items large then others. Add MySql DBAdapter Improve performance for multi-fields sort . Using hash table to access the Payload data. The version before used bin search. Using heap sort instead of qui...Silverlight????[???]: silverlight????[???]2.0: ???????，?????，????????silverlight????。DBSourceTools: DBSourceTools_1.3.0.0: Release 1.3.0.0 Changed editors from FireEdit to ICSharpCode.TextEditor. Complete re-vamp of Intellisense ( further testing needed). Hightlight Field and Table Names in sql scripts. Added field dropdown on all tables and views in DBExplorer. Added data option for viewing data in Tables. Fixed comment / uncomment bug as reported by tareq. Included Synonyms in scripting engine ( nickt_ch ).IronPython: 2.7 Release Candidate 1: We are pleased to announce the first Release Candidate for IronPython 2.7. This release contains over two dozen bugs fixed in preparation for 2.7 Final. See the release notes for 60193 for details and what has already been fixed in the earlier 2.7 prereleases. - IronPython TeamCaliburn Micro: A Micro-Framework for WPF, Silverlight and WP7: Caliburn.Micro 1.0 RC: This is the official Release Candicate for Caliburn.Micro 1.0. The download contains the binaries, samples and VS templates. VS Templates The templates included are designed for situations where the Caliburn.Micro source needs to be embedded within a single project solution. This was targeted at government and other organizations that expressed specific requirements around using an open source project like this. NuGet This release does not have a corresponding NuGet package. The NuGet pack...Caliburn: A Client Framework for WPF and Silverlight: Caliburn 2.0 RC: This is the official Release Candidate for Caliburn 2.0. It contains all binaries, samples and generated code docs.Chiave File Encryption: Chiave 0.9: Application for file encryption and decryption using 512 Bit rijndael encyrption algorithm with simple to use UI. Its written in C# and compiled in .Net version 3.5. It incorporates features of Windows 7 like Jumplists, Taskbar progress and Aero Glass. Feedbacks are Welcome!....Rawr: Rawr 4.0.20 Beta: Rawr is now web-based. The link to use Rawr4 is: http://elitistjerks.com/rawr.phpThis is the Cataclysm Beta Release. More details can be found at the following link http://rawr.codeplex.com/Thread/View.aspx?ThreadId=237262 As of the 4.0.16 release, you can now also begin using the new Downloadable WPF version of Rawr!This is a pre-alpha release of the WPF version, there are likely to be a lot of issues. If you have a problem, please follow the Posting Guidelines and put it into the Issue Trac...PowerGUI Visual Studio Extension: PowerGUI VSX 1.3.2: New FeaturesPowerGUI Console Tool Window PowerShell Project Type PowerGUI 2.4 SupportMiniTwitter: 1.66: MiniTwitter 1.66 ???? ?? ?????????? 2 ??????????????????? User Streams ?????????Windows Phone 7 Isolated Storage Explorer: WP7 Isolated Storage Explorer v1.0 Beta: Current release features:WPF desktop explorer client Visual Studio integrated tool window explorer client (Visual Studio 2010 Professional and above) Supported operations: Refresh (isolated storage information), Add Folder, Add Existing Item, Download File, Delete Folder, Delete File Explorer supports operations running on multiple remote applications at the same time Explorer detects application disconnect (1-2 second delay) Explorer confirms operation completed status Explorer d...Image.Viewer: 2011: First version of 2011Silverlight Toolkit: Silverlight for Windows Phone Toolkit - Feb 2011: Silverlight for Windows Phone Toolkit OverviewSilverlight for Windows Phone Toolkit offers developers additional controls for Windows Phone application development, designed to match the rich user experience of the Windows Phone 7. Suggestions? Features? Questions? Ask questions in the Create.msdn.com forum. Add bugs or feature requests to the Issue Tracker. Help us shape the Silverlight Toolkit with your feedback! Please clearly indicate that the work items and issues are for the phone t...New Projects.Net Dating & Social Software Suite: A free, open source dating and social software suite. Dot Net Dating Suite uses the latest features in .Net combined with experienced developers efforts. This allows us to deliver professional public SEO websites with the support of an enterprise enabled administration suite.AllegroSharp: Biblioteka zapewniajaca obsluge serwisu aukcyjnego Allegro.pl w oparciu o udostepniona publicznie usluge Allegro Web API.asdfasdfasdf: asdfasdfasdfauto: auto siteAWS Monitor: A web app utilizing the Amazon Web Services API with a focus on browsing through and analyzing data graphically, mostly from CloudWatch - the API providing metrics about the usage of all the Amazon Web Services such as EC2 (Cloud Computing) and ELB (Elastic Load Balancing).Calculation of FEM using DirectX Libraries: Calculation of FEM using DirectX LibrariesCART: System CART (Creative Application to Remedy Traffics) poprawi przepustowosc infrastruktury drogowej i plynnosci ruchu pojazdów w aglomeracjach miejskich. Chaining Assertion for MSTest: Chaining Assertion for MSTest. Simpleness Assert Extension Method on Object. This provides only one .cs file.CodeFirst Membership Provider: Custom Membership Provider based on SimpleMembershipProvider using Entity Framework Code-First, intended for use in ASP.NET MVC 3. Thanks to ASP.NET Web Pages team for building a simple membership provider :PFourSquareSharp: Simple OAuth2 Implementation of FourSquare API in .NETHelix Engine: The Helix Engine is an Isometric Rendering Engine for SilverlightLighthouse - Versatile Unit Test Runner for Silverlight: Lighthouse provides you with set of simple but powerful tools to run Silverlight Unit Tests from Command Line, Windows Test Runner Application and from Resharper plugin for Visual Studio.MISCE: Designs for a Minimal Instruction Set Computer for Education along with a simulator/compiler written in Excel. A computer "from first principles" that utilises a minimal instruction set and can be built for demonstration purposes as part of a technology or computing course. Oh My Log: Oh My Log inventorises eventlog files from Windows Servers in a network. Clean and simple sysadmin tool. OSIS Interop Tests: These are the tests created for use by the OSIS working group (http://osis.idcommons.net) to test interoperability features of user-centric solutions during interop events.Program Options: Parse command line optionsSearchable Property Updater for Microsoft Dynamics CRM 2011: Searchable Property Updater makes it easier for Microsoft Dynamics CRM 2011 customizers to bulk change the "Active for advanced find" property of entities attributesSilverlight Bolo: silverlight bolo cloneSimulacia a vizualizacia vlasov: simulacia a vizualizacia vlasov pomocou GPUSmartkernel: Smartkernel:Framework,Example,Platform,Tool,AppSusuCMS: SusuCMSSwimlanes for Scrum: Swimlanes Taskboard for Scrum Team Projects with TFS setup using SfTS (Scrum for Team System) V3 templateteamdoer: These are the actual source codes that power teamdoer.com - a simple collaborative task/project management software apptiencd: Tiencd projectVG Current Item Display Web Part: VG Current Item Display Web Part allows to display current SharePoint item metadata. For example if you put it on to the Web Part page or list item form it will display the custom view of the current item properties. Output is easily customized with XSLT file.Virtual Interactive Shopper: Addin for SeeMe Rehabilitation System. More information about the SeeMe system can be found at http://www.brontesprocessing.com/health/SeeMeVisual Studio Strategy Manager: Provide a way to create code generation strategies and to manage them in Visual Studio 2010. Strategies can interact with Visual Studio events like document events (saved, closed, opened), building event or DSL Tools events (model element created, deleted, modified..).VMarket: <project name>VMarket</project name> <programming language>asp.net</programming language> <project description> VMarket is virtual market systems which allow users to act as seller or buyer and manage their property online </project description>webclerk: webclerk's project based on microsoft techWebTest: Just Test!Work efficiency (WE) ????????: Work efficiency ???????? ????： ???? ????zrift: nothing here, move along

  Read the article

• Create nice animation on your ASP.NET Menu control using jQuery

  - by hajan

  In this blog post, I will show how you can apply some nice animation effects on your ASP.NET Menu control. ASP.NET Menu control offers many possibilities, but together with jQuery, you can make very rich, interactive menu accompanied with animations and effects. Lets start with an example: - Create new ASP.NET Web Application and give it a name - Open your Default.aspx page (or any other .aspx page where you will create the menu) - Our page ASPX code is: <form id="form1" runat="server"> <div id="menu">     <asp:Menu ID="Menu1" runat="server" Orientation="Horizontal" RenderingMode="List">                     <Items>             <asp:MenuItem NavigateUrl="~/Default.aspx" ImageUrl="~/Images/Home.png" Text="Home" Value="Home"  />             <asp:MenuItem NavigateUrl="~/About.aspx" ImageUrl="~/Images/Friends.png" Text="About Us" Value="AboutUs" />             <asp:MenuItem NavigateUrl="~/Products.aspx" ImageUrl="~/Images/Box.png" Text="Products" Value="Products" />             <asp:MenuItem NavigateUrl="~/Contact.aspx" ImageUrl="~/Images/Chat.png" Text="Contact Us" Value="ContactUs" />         </Items>     </asp:Menu> </div> </form> As you can see, we have ASP.NET Menu with Horizontal orientation and RenderMode=”List”. It has four Menu Items where for each I have specified NavigateUrl, ImageUrl, Text and Value properties. All images are in Images folder in the root directory of this web application. The images I’m using for this demo are from Free Web Icons. - Next, lets create CSS for the LI and A tags (place this code inside head tag) <style type="text/css">     li     {         border:1px solid black;         padding:20px 20px 20px 20px;         width:110px;         background-color:Gray;         color:White;         cursor:pointer;     }     a { color:White; font-family:Tahoma; } </style> This is nothing very important and you can change the style as you want. - Now, lets reference the jQuery core library directly from Microsoft CDN. <script type="text/javascript" src="http://ajax.aspnetcdn.com/ajax/jQuery/jquery-1.4.4.min.js"></script> - And we get to the most interesting part, applying the animations with jQuery Before we move on writing jQuery code, lets see what is the HTML code that our ASP.NET Menu control generates in the client browser.   <ul class="level1">     <li><a class="level1" href="Default.aspx"><img src="Images/Home.png" alt="" title="" class="icon" />Home</a></li>     <li><a class="level1" href="About.aspx"><img src="Images/Friends.png" alt="" title="" class="icon" />About Us</a></li>     <li><a class="level1" href="Products.aspx"><img src="Images/Box.png" alt="" title="" class="icon" />Products</a></li>     <li><a class="level1" href="Contact.aspx"><img src="Images/Chat.png" alt="" title="" class="icon" />Contact Us</a></li> </ul>   So, it generates unordered list which has class level1 and for each item creates li element with an anchor with image + menu text inside it. If we want to access the list element only from our menu (not other list element sin the page), we need to use the following jQuery selector: “ul.level1 li”, which will find all li elements which have parent element ul with class level1. Hence, the jQuery code is:   <script type="text/javascript">     $(function () {         $("ul.level1 li").hover(function () {             $(this).stop().animate({ opacity: 0.7, width: "170px" }, "slow");         }, function () {             $(this).stop().animate({ opacity: 1, width: "110px" }, "slow");         });     }); </script>   I’m using hover, so that the animation will occur once we go over the menu item. The two different functions are one for the over, the other for the out effect. The following line $(this).stop().animate({ opacity: 0.7, width: "170px" }, "slow");     does the real job. So, this will first stop any previous animations (if any) that are in progress and will animate the menu item by giving to it opacity of 0.7 and changing the width to 170px (the default width is 110px as in the defined CSS style for li tag). This happens on mouse over. The second function on mouse out reverts the opacity and width properties to the default ones. The last parameter “slow” is the speed of the animation. The end result is:   The complete ASPX code: <html xmlns="http://www.w3.org/1999/xhtml"> <head runat="server">     <title>ASP.NET Menu + jQuery</title>     <style type="text/css">         li         {             border:1px solid black;             padding:20px 20px 20px 20px;             width:110px;             background-color:Gray;             color:White;             cursor:pointer;         }         a { color:White; font-family:Tahoma; }     </style>     <script type="text/javascript" src="http://ajax.aspnetcdn.com/ajax/jQuery/jquery-1.4.4.min.js"></script>     <script type="text/javascript">         $(function () {             $("ul.level1 li").hover(function () {                 $(this).stop().animate({ opacity: 0.7, width: "170px" }, "slow");             }, function () {                 $(this).stop().animate({ opacity: 1, width: "110px" }, "slow");             });         });     </script> </head> <body>     <form id="form1" runat="server">     <div id="menu">         <asp:Menu ID="Menu1" runat="server" Orientation="Horizontal" RenderingMode="List">                         <Items>                 <asp:MenuItem NavigateUrl="~/Default.aspx" ImageUrl="~/Images/Home.png" Text="Home" Value="Home"  />                 <asp:MenuItem NavigateUrl="~/About.aspx" ImageUrl="~/Images/Friends.png" Text="About Us" Value="AboutUs" />                 <asp:MenuItem NavigateUrl="~/Products.aspx" ImageUrl="~/Images/Box.png" Text="Products" Value="Products" />                 <asp:MenuItem NavigateUrl="~/Contact.aspx" ImageUrl="~/Images/Chat.png" Text="Contact Us" Value="ContactUs" />             </Items>         </asp:Menu>     </div>     </form> </body> </html> Hope this was useful. Regards, Hajan

  Read the article

• Clustering Basics and Challenges

  - by Karoly Vegh

  For upcoming posts it seemed to be a good idea to dedicate some time for cluster basic concepts and theory. This post misses a lot of details that would explode the articlesize, should you have questions, do not hesitate to ask them in the comments.  The goal here is to get some concepts straight. I can't promise to give you an overall complete definitions of cluster, cluster agent, quorum, voting, fencing, split brain condition, so the following is more of an explanation. Here we go. -------- Cluster, HA, failover, switchover, scalability -------- An attempted definition of a Cluster: A cluster is a set (2+) server nodes dedicated to keep application services alive, communicating through the cluster software/framework with eachother, test and probe health status of servernodes/services and with quorum based decisions and with switchover/failover techniques keep the application services running on them available. That is, should a node that runs a service unexpectedly lose functionality/connection, the other ones would take over the and run the services, so that availability is guaranteed. To provide availability while strictly sticking to a consistent clusterconfiguration is the main goal of a cluster.  At this point we have to add that this defines a HA-cluster, a High-Availability cluster, where the clusternodes are planned to run the services in an active-standby, or failover fashion. An example could be a single instance database. Some applications can be run in a distributed or scalable fashion. In the latter case instances of the application run actively on separate clusternodes serving servicerequests simultaneously. An example for this version could be a webserver that forwards connection requests to many backend servers in a round-robin way. Or a database running in active-active RAC setup.  -------- Cluster arhitecture, interconnect, topologies -------- Now, what is a cluster made of? Servers, right. These servers (the clusternodes) need to communicate. This of course happens over the network, usually over dedicated network interfaces interconnecting all the clusternodes. These connection are called interconnects.How many clusternodes are in a cluster? There are different cluster topologies. The most simple one is a clustered pair topology, involving only two clusternodes:  There are several more topologies, clicking the image above will take you to the relevant documentation. Also, to answer the question Solaris Cluster allows you to run up to 16 servers in a cluster. Where shall these clusternodes be placed? A very important question. The right answer is: It depends on what you plan to achieve with the cluster. Do you plan to avoid only a server outage? Then you can place them right next to eachother in the datacenter. Do you need to avoid DataCenter outage? In that case of course you should place them at least in different fire zones. Or in two geographically distant DataCenters to avoid disasters like floods, large-scale fires or power outages. We call this a stretched- or campus cluster, the clusternodes being several kilometers away from eachother. To cover really large distances, you probably need to move to a GeoCluster, which is a different kind of animal.  What is a geocluster? A Geographic Cluster in Solaris Cluster terms is actually a metacluster between two, separate (locally-HA) clusters.  -------- Cluster resource types, agents, resources, resource groups -------- So how does the cluster manage my applications? The cluster needs to start, stop and probe your applications. If you application runs, the cluster needs to check regularly if the application state is healthy, does it respond over the network, does it have all the processes running, etc. This is called probing. If the cluster deems the application is in a faulty state, then it can try to restart it locally or decide to switch (stop on node A, start on node B) the service. Starting, stopping and probing are the three actions that a cluster agent does. There are many different kinds of agents included in Solaris Cluster, but you can build your own too. Examples are an agent that manages (mounts, moves) ZFS filesystems, or the Oracle DB HA agent that cares about the database, or an agent that moves a floating IP address between nodes. There are lots of other agents included for Apache, Tomcat, MySQL, Oracle DB, Oracle Weblogic, Zones, LDoms, NFS, DNS, etc.We also need to clarify the difference between a cluster resource and the cluster resource group.A cluster resource is something that is managed by a cluster agent. Cluster resource types are included in Solaris cluster (see above, e.g. HAStoragePlus, HA-Oracle, LogicalHost). You can group cluster resources into cluster resourcegroups, and switch these groups together from one node to another. To stick to the example above, to move an Oracle DB service from one node to another, you have to switch the group between nodes, and the agents of the cluster resources in the group will do the following:  On node A Shut down the DB Unconfigure the LogicalHost IP the DB Listener listens on unmount the filesystem   Then, on node B: mount the FS configure the IP  startup the DB -------- Voting, Quorum, Split Brain Condition, Fencing, Amnesia -------- How do the clusternodes agree upon their action? How do they decide which node runs what services? Another important question. Running a cluster is a strictly democratic thing.Every node has votes, and you need the majority of votes to have the deciding power. Now, this is usually no problem, clusternodes think very much all alike. Still, every action needs to be governed upon in a productive system, and has to be agreed upon. Agreeing is easy as long as the clusternodes all behave and talk to eachother over the interconnect. But if the interconnect is gone/down, this all gets tricky and confusing. Clusternodes think like this: "My job is to run these services. The other node does not answer my interconnect communication, it must be down. I'd better take control and run the services!". The problem is, as I have already mentioned, clusternodes very much think alike. If the interconnect is gone, they all assume the other node is down, and they all want to mount the data backend, enable the IP and run the database. Double IPs, double mounts, double DB instances - now that is trouble. Also, in a 2-node cluster they both have only 50% of the votes, that is, they themselves alone are not allowed to run a cluster.  This is where you need a quorum device. According to Wikipedia, the "requirement for a quorum is protection against totally unrepresentative action in the name of the body by an unduly small number of persons.". They need additional votes to run the cluster. For this requirement a 2-node cluster needs a quorum device or a quorum server. If the interconnect is gone, (this is what we call a split brain condition) both nodes start to race and try to reserve the quorum device to themselves. They do this, because the quorum device bears an additional vote, that could ensure majority (50% +1). The one that manages to lock the quorum device (e.g. if it's an FC LUN, it SCSI reserves it) wins the right to build/run a cluster, the other one - realizing he was late - panics/reboots to ensure the cluster config stays consistent.  Losing the interconnect isn't only endangering the availability of services, but it also endangers the cluster configuration consistence. Just imagine node A being down and during that the cluster configuration changes. Now node B goes down, and node A comes up. It isn't uptodate about the cluster configuration's changes so it will refuse to start a cluster, since that would lead to cluster amnesia, that is the cluster had some changes, but now runs with an older cluster configuration repository state, that is it's like it forgot about the changes.  Also, to ensure application data consistence, the clusternode that wins the race makes sure that a server that isn't part of or can't currently join the cluster can access the devices. This procedure is called fencing. This usually happens to storage LUNs via SCSI reservation.  Now, another important question: Where do I place the quorum disk?  Imagine having two sites, two separate datacenters, one in the north of the city and the other one in the south part of it. You run a stretched cluster in the clustered pair topology. Where do you place the quorum disk/server? If you put it into the north DC, and that gets hit by a meteor, you lose one clusternode, which isn't a problem, but you also lose your quorum, and the south clusternode can't keep the cluster running lacking the votes. This problem can't be solved with two sites and a campus cluster. You will need a third site to either place the quorum server to, or a third clusternode. Otherwise, lacking majority, if you lose the site that had your quorum, you lose the cluster. Okay, we covered the very basics. We haven't talked about virtualization support, CCR, ClusterFilesystems, DID devices, affinities, storage-replication, management tools, upgrade procedures - should those be interesting for you, let me know in the comments, along with any other questions. Given enough demand I'd be glad to write a followup post too. Now I really want to move on to the second part in the series: ClusterInstallation.  Oh, as for additional source of information, I recommend the documentation: http://docs.oracle.com/cd/E23623_01/index.html, and the OTN Oracle Solaris Cluster site: http://www.oracle.com/technetwork/server-storage/solaris-cluster/index.html

  Read the article

• What to Do When Windows Won’t Boot

  - by Chris Hoffman

  You turn on your computer one day and Windows refuses to boot — what do you do? “Windows won’t boot” is a common symptom with a variety of causes, so you’ll need to perform some troubleshooting. Modern versions of Windows are better at recovering from this sort of thing. Where Windows XP might have stopped in its tracks when faced with this problem, modern versions of Windows will try to automatically run Startup Repair. First Things First Be sure to think about changes you’ve made recently — did you recently install a new hardware driver, connect a new hardware component to your computer, or open your computer’s case and do something? It’s possible the hardware driver is buggy, the new hardware is incompatible, or that you accidentally unplugged something while working inside your computer. The Computer Won’t Power On At All If your computer won’t power on at all, ensure it’s plugged into a power outlet and that the power connector isn’t loose. If it’s a desktop PC, ensure the power switch on the back of its case — on the power supply — is set to the On position. If it still won’t power on at all, it’s possible you disconnected a power cable inside its case. If you haven’t been messing around inside the case, it’s possible the power supply is dead. In this case, you’ll have to get your computer’s hardware fixed or get a new computer. Be sure to check your computer monitor — if your computer seems to power on but your screen stays black, ensure your monitor is powered on and that the cable connecting it to your computer’s case is plugged in securely at both ends. The Computer Powers On And Says No Bootable Device If your computer is powering on but you get a black screen that says something like “no bootable device” or another sort of “disk error” message, your computer can’t seem to boot from the hard drive that Windows was installed on. Enter your computer’s BIOS or UEFI firmware setup screen and check its boot order setting, ensuring that it’s set to boot from its hard drive. If the hard drive doesn’t appear in the list at all, it’s possible your hard drive has failed and can no longer be booted from. In this case, you may want to insert Windows installation or recovery media and run the Startup Repair operation. This will attempt to make Windows bootable again. For example, if something overwrote your Windows drive’s boot sector, this will repair the boot sector. If the recovery environment won’t load or doesn’t see your hard drive, you likely have a hardware problem. Be sure to check your BIOS or UEFI’s boot order first if the recovery environment won’t load. You can also attempt to manually fix Windows boot loader problems using the fixmbr and fixboot commands. Modern versions of Windows should be able to fix this problem for you with the Startup Repair wizard, so you shouldn’t actually have to run these commands yourself. Windows Freezes or Crashes During Boot If Windows seems to start booting but fails partway through, you may be facing either a software or hardware problem. If it’s a software problem, you may be able to fix it by performing a Startup Repair operation. If you can’t do this from the boot menu, insert a Windows installation disc or recovery disk and use the startup repair tool from there. If this doesn’t help at all, you may want to reinstall Windows or perform a Refresh or Reset on Windows 8. If the computer encounters errors while attempting to perform startup repair or reinstall Windows, or the reinstall process works properly and you encounter the same errors afterwards, you likely have a hardware problem. Windows Starts and Blue Screens or Freezes If Windows crashes or blue-screens on you every time it boots, you may be facing a hardware or software problem. For example, malware or a buggy driver may be loading at boot and causing the crash, or your computer’s hardware may be malfunctioning. To test this, boot your Windows computer in safe mode. In safe mode, Windows won’t load typical hardware drivers or any software that starts automatically at startup. If the computer is stable in safe mode, try uninstalling any recently installed hardware drivers, performing a system restore, and scanning for malware. If you’re lucky, one of these steps may fix your software problem and allow you to boot Windows normally. If your problem isn’t fixed, try reinstalling Windows or performing a Refresh or Reset on Windows 8. This will reset your computer back to its clean, factory-default state. If you’re still experiencing crashes, your computer likely has a hardware problem. Recover Files When Windows Won’t Boot If you have important files that will be lost and want to back them up before reinstalling Windows, you can use a Windows installer disc or Linux live media to recover the files. These run entirely from a CD, DVD, or USB drive and allow you to copy your files to another external media, such as another USB stick or an external hard drive. If you’re incapable of booting a Windows installer disc or Linux live CD, you may need to go into your BIOS or UEFI and change the boot order setting. If even this doesn’t work — or if you can boot from the devices and your computer freezes or you can’t access your hard drive — you likely have a hardware problem. You can try pulling the computer’s hard drive, inserting it into another computer, and recovering your files that way. Following these steps should fix the vast majority of Windows boot issues — at least the ones that are actually fixable. The dark cloud that always hangs over such issues is the possibility that the hard drive or another component in the computer may be failing. Image Credit: Karl-Ludwig G. Poggemann on Flickr, Tzuhsun Hsu on Flickr     

  Read the article

• CodePlex Daily Summary for Friday, September 07, 2012

  CodePlex Daily Summary for Friday, September 07, 2012Popular ReleasesUmbraco CMS: Umbraco 4.9.0: Whats newThe media section has been overhauled to support HTML5 uploads, just drag and drop files in, even multiple files are supported on any HTML5 capable browser. The folder content overview is also much improved allowing you to filter it and perform common actions on your media items. The Rich Text Editor’s “Media” button now uses an embedder based on the open oEmbed standard (if you’re upgrading, enable the media button in the Rich Text Editor datatype settings and set TidyEditorConten...menu4web: menu4web 0.4.1 - javascript menu for web sites: This release is for those who believe that global variables are evil. menu4web has been wrapped into m4w singleton object. Added "Vertical Tabs" example which illustrates object notation.WinRT XAML Toolkit: WinRT XAML Toolkit - 1.2.1: WinRT XAML Toolkit based on the Windows 8 RTM SDK. Download the latest source from the SOURCE CODE page. For compiled version use NuGet. You can add it to your project in Visual Studio by going to View/Other Windows/Package Manager Console and entering: PM> Install-Package winrtxamltoolkit Features AsyncUI extensions Controls and control extensions Converters Debugging helpers Imaging IO helpers VisualTree helpers Samples Recent changes NOTE: Namespace changes DebugConsol...iPDC - Free Phasor Data Concentrator: iPDC-v1.3.1: iPDC suite version-1.3.1, Modifications and Bug Fixed (from v 1.3.0) New User Manual for iPDC-v1.3.1 available on websites. Bug resolved : PMU Simulator TCP connection error and hang connection for client (PDC). Now PMU Simulator (server) can communicate more than one PDCs (clients) over TCP and UDP parallely. PMU Simulator is now sending the exact data frames as mentioned in data rate by user. PMU Simulator data rate has been verified by iPDC database entries and PMU Connection Tes...Microsoft SQL Server Product Samples: Database: AdventureWorks OData Feed: The AdventureWorks OData service exposes resources based on specific SQL views. The SQL views are a limited subset of the AdventureWorks database that results in several consuming scenarios: CompanySales Documents ManufacturingInstructions ProductCatalog TerritorySalesDrilldown WorkOrderRouting How to install the sample You can consume the AdventureWorks OData feed from http://services.odata.org/AdventureWorksV3/AdventureWorks.svc. You can also consume the AdventureWorks OData fe...Desktop Google Reader: 1.4.6: Sorting feeds alphabetical is now optional (see preferences window)DotNetNuke® Community Edition CMS: 06.02.03: Major Highlights Fixed issue where mailto: links were not working when sending bulk email Fixed issue where uses did not see friendship relationships Problem is in 6.2, which does not show in the Versions Affected list above. Fixed the issue with cascade deletes in comments in CoreMessaging_Notification Fixed UI issue when using a date fields as a required profile property during user registration Fixed error when running the product in debug mode Fixed visibility issue when...Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.65: Fixed null-reference error in the build task constructor.B INI Sharp Library: B INI Sharp Library v1.0.0.0 Final Realsed: The frist realsedActive Social Migrator: ActiveSocialMigrator 1.0.0 Beta: Beta release for the Active Social Migration tool.EntLib.com????????: ??????demo??-For SQL 2005-2008: EntLibShopping ???v3.0 - ??????demo??，?????SQL SERVER 2005/2008/2008 R2/2012 ??????。 ??（??）??????。 THANKS.Sistem LPK Pemkot Semarang: Panduan Penggunaan Sistem LPK: Panduan cara menggunakan Aplikasi Sistem LPK Bagian Pembangunan Kota SemarangActive Forums for DotNetNuke CMS: Active Forums 5.0.0 RC: RC release of Active Forums 5.0.Droid Explorer: Droid Explorer 0.8.8.7 Beta: Bug in the display icon for apk's, will fix with next release Added fallback icon if unable to get the image/icon from the Cloud Service Removed some stale plugins that were either out dated or incomplete. Added handler for *.ab files for restoring backups Added plugin to create device backups Backups stored in %USERPROFILE%\Android Backups\%DEVICE_ID%\ Added custom folder icon for the android backups directory better error handling for installing an apk bug fixes for the Runn...The Visual Guide for Building Team Foundation Server 2012 Environments: Version 1: --Nearforums - ASP.NET MVC forum engine: Nearforums v8.5: Version 8.5 of Nearforums, the ASP.NET MVC Forum Engine. New features include: Built-in search engine using Lucene.NET Flood control improvements Notifications improvements: sync option and mail body View Roadmap for more details webdeploy package sha1 checksum: 961aff884a9187b6e8a86d68913cdd31f8deaf83WiX Toolset: WiX Toolset v3.6: WiX Toolset v3.6 introduces the Burn bootstrapper/chaining engine and support for Visual Studio 2012 and .NET Framework 4.5. Other minor functionality includes: WixDependencyExtension supports dependency checking among MSI packages. WixFirewallExtension supports more features of Windows Firewall. WixTagExtension supports Software Id Tagging. WixUtilExtension now supports recursive directory deletion. Melt simplifies pure-WiX patching by extracting .msi package content and updating .w...Iveely Search Engine: Iveely Search Engine （0.2.0）: ????ISE?0.1.0??，?????，ISE?0.2.0?????????，???????，????????20???follow?ISE，????，??ISE??????????，??????????，?????????，?????????0.2.0??????，??????????。 Iveely Search Engine ?0.2.0?????????“??????????”，??????，?????????，???????，???????????????????，????、????????????。???0.1.0????????????： 1. ??“????” ??。??????????，?????????，???????????????????。??：????????，????????????，??????????????????。??????。 2. ??“????”??。?0.1.0??????，???????，???????????????，?????????????，????????，?0.2.0?，???????...GmailDefaultMaker: GmailDefaultMaker 3.0.0.2: Add QQ Mail BugfixSmart Data Access layer: Smart Data access Layer Ver 3: In this version support executing inline query is added. Check Documentation section for detail.New ProjectsAdding 2013 Jewish Holidays for Outlook2003: Instruction: Copy the outlook.hol file to your compuer where Outlook2003 is installed. Double click the file, choose "Israel" and continue. That's it Agilcont System: Sistema de contabilidad para empresas privadas de preferencia para cajas que trabajan con efectivo en soles, dolares y con el material oroARB (A Request Broker): The idea is something like a Request Broker, but with some additional functionality.BATTLE.NET - SDK: This SDK provides the ability to use the Battle.net (Blizzard) Services for all supported Games such Diablo 3, World of Warcraft. Container Terminal System: SummaryDeclarative UX Streaming Data Language for the Cloud: Bringing a better communication paradigm for media and data..Get User Profile Information from SharePoint UserProfile Service: Used SharePoint object model to get the user profile information from the User Profile Service.Guess The City & State Windows 8 Source Code: Source code for Guess The City & State in Malaysia Windows 8 AppJquery Tree: This project is to demonstrate tree basic functionality.MCEBuddy 2.x: Convert and Remove Commercials for your Windows Media CenterMvcDesign: MvcDesign engine implementation projectMy Task Manager: This is a task manager module for DotNetNuke. I am using it to get started developing modules.MyAppwithbranches: MyAppwithbranchesProjecte prova: rpyGEO: pyGEO is a python package capable of parsing microarray data files. It also has a primitive plotting function.Scarlet Road: Scarlet Road is a top-down shooter. It's you against an unending horde of monsters.simplecounter: A simple counter, cick and counter.SiteEmpires: ????????Soundcloud Loader: Simple Tool for downloading Tracks from Soundcloud.Windows Phone Samples: Windows Phone code samples.

  Read the article

• How can a code editor effectively hint at code nesting level - without using indentation?

  - by pgfearo

  I've written an XML text editor that provides 2 view options for the same XML text, one indented (virtually), the other left-justified. The motivation for the left-justified view is to help users 'see' the whitespace characters they're using for indentation of plain-text or XPath code without interference from indentation that is an automated side-effect of the XML context. I want to provide visual clues (in the non-editable part of the editor) for the left-justified mode that will help the user, but without getting too elaborate. I tried just using connecting lines, but that seemed too busy. The best I've come up with so far is shown in a mocked up screenshot of the editor below, but I'm seeking better/simpler alternatives (that don't require too much code). [Edit] Taking the heatmap idea (from: @jimp) I get this and 3 alternatives - labelled a, b and c: The following section describes the accepted answer as a proposal, bringing together ideas from a number of other answers and comments. As this question is now community wiki, please feel free to update this. NestView The name for this idea which provides a visual method to improve the readability of nested code without using indentation. Contour Lines The name for the differently shaded lines within the NestView The image above shows the NestView used to help visualise an XML snippet. Though XML is used for this illustration, any other code syntax that uses nesting could have been used for this illustration. An Overview: The contour lines are shaded (as in a heatmap) to convey nesting level The contour lines are angled to show when a nesting level is being either opened or closed. A contour line links the start of a nesting level to the corresponding end. The combined width of contour lines give a visual impression of nesting level, in addition to the heatmap. The width of the NestView may be manually resizable, but should not change as the code changes. Contour lines can either be compressed or truncated to keep acheive this. Blank lines are sometimes used code to break up text into more digestable chunks. Such lines could trigger special behaviour in the NestView. For example the heatmap could be reset or a background color contour line used, or both. One or more contour lines associated with the currently selected code can be highlighted. The contour line associated with the selected code level would be emphasized the most, but other contour lines could also 'light up' in addition to help highlight the containing nested group Different behaviors (such as code folding or code selection) can be associated with clicking/double-clicking on a Contour Line. Different parts of a contour line (leading, middle or trailing edge) may have different dynamic behaviors associated. Tooltips can be shown on a mouse hover event over a contour line The NestView is updated continously as the code is edited. Where nesting is not well-balanced assumptions can be made where the nesting level should end, but the associated temporary contour lines must be highlighted in some way as a warning. Drag and drop behaviors of Contour Lines can be supported. Behaviour may vary according to the part of the contour line being dragged. Features commonly found in the left margin such as line numbering and colour highlighting for errors and change state could overlay the NestView. Additional Functionality The proposal addresses a range of additional issues - many are outside the scope of the original question, but a useful side-effect. Visually linking the start and end of a nested region The contour lines connect the start and end of each nested level Highlighting the context of the currently selected line As code is selected, the associated nest-level in the NestView can be highlighted Differentiating between code regions at the same nesting level In the case of XML different hues could be used for different namespaces. Programming languages (such as c#) support named regions that could be used in a similar way. Dividing areas within a nesting area into different visual blocks Extra lines are often inserted into code to aid readability. Such empty lines could be used to reset the saturation level of the NestView's contour lines. Multi-Column Code View Code without indentation makes the use of a multi-column view more effective because word-wrap or horizontal scrolling is less likely to be required. In this view, once code has reach the bottom of one column, it flows into the next one: Usage beyond merely providing a visual aid As proposed in the overview, the NestView could provide a range of editing and selection features which would be broadly in line with what is expected from a TreeView control. The key difference is that a typical TreeView node has 2 parts: an expander and the node icon. A NestView contour line can have as many as 3 parts: an opener (sloping), a connector (vertical) and a close (sloping). On Indentation The NestView presented alongside non-indented code complements, but is unlikely to replace, the conventional indented code view. It's likely that any solutions adopting a NestView, will provide a method to switch seamlessly between indented and non-indented code views without affecting any of the code text itself - including whitespace characters. One technique for the indented view would be 'Virtual Formatting' - where a dynamic left-margin is used in lieu of tab or space characters. The same nesting-level data used to dynamically render the NestView could also used for the more conventional-looking indented view. Printing Indentation will be important for the readability of printed code. Here, the absence of tab/space characters and a dynamic left-margin means that the text can wrap at the right-margin and still maintain the integrity of the indented view. Line numbers can be used as visual markers that indicate where code is word-wrapped and also the exact position of indentation: Screen Real-Estate: Flat Vs Indented Addressing the question of whether the NestView uses up valuable screen real-estate: Contour lines work well with a width the same as the code editor's character width. A NestView width of 12 character widths can therefore accommodate 12 levels of nesting before contour lines are truncated/compressed. If an indented view uses 3 character-widths for each nesting level then space is saved until nesting reaches 4 levels of nesting, after this nesting level the flat view has a space-saving advantage that increases with each nesting level. Note: A minimum indentation of 4 character widths is often recommended for code, however XML often manages with less. Also, Virtual Formatting permits less indentation to be used because there's no risk of alignment issues A comparison of the 2 views is shown below: Based on the above, its probably fair to conclude that view style choice will be based on factors other than screen real-estate. The one exception is where screen space is at a premium, for example on a Netbook/Tablet or when multiple code windows are open. In these cases, the resizable NestView would seem to be a clear winner. Use Cases Examples of real-world examples where NestView may be a useful option: Where screen real-estate is at a premium a. On devices such as tablets, notepads and smartphones b. When showing code on websites c. When multiple code windows need to be visible on the desktop simultaneously Where consistent whitespace indentation of text within code is a priority For reviewing deeply nested code. For example where sub-languages (e.g. Linq in C# or XPath in XSLT) might cause high levels of nesting. Accessibility Resizing and color options must be provided to aid those with visual impairments, and also to suit environmental conditions and personal preferences: Compatability of edited code with other systems A solution incorporating a NestView option should ideally be capable of stripping leading tab and space characters (identified as only having a formatting role) from imported code. Then, once stripped, the code could be rendered neatly in both the left-justified and indented views without change. For many users relying on systems such as merging and diff tools that are not whitespace-aware this will be a major concern (if not a complete show-stopper). Other Works: Visualisation of Overlapping Markup Published research by Wendell Piez, dated from 2004, addresses the issue of the visualisation of overlapping markup, specifically LMNL. This includes SVG graphics with significant similarities to the NestView proposal, as such, they are acknowledged here. The visual differences are clear in the images (below), the key functional distinction is that NestView is intended only for well-nested XML or code, whereas Wendell Piez's graphics are designed to represent overlapped nesting. The graphics above were reproduced - with kind permission - from http://www.piez.org Sources: Towards Hermenutic Markup Half-steps toward LMNL

  Read the article

• So…is it a Seek or a Scan?

  - by Paul White

  You’re probably most familiar with the terms ‘Seek’ and ‘Scan’ from the graphical plans produced by SQL Server Management Studio (SSMS).  The image to the left shows the most common ones, with the three types of scan at the top, followed by four types of seek.  You might look to the SSMS tool-tip descriptions to explain the differences between them: Not hugely helpful are they?  Both mention scans and ranges (nothing about seeks) and the Index Seek description implies that it will not scan the index entirely (which isn’t necessarily true). Recall also yesterday’s post where we saw two Clustered Index Seek operations doing very different things.  The first Seek performed 63 single-row seeking operations; and the second performed a ‘Range Scan’ (more on those later in this post).  I hope you agree that those were two very different operations, and perhaps you are wondering why there aren’t different graphical plan icons for Range Scans and Seeks?  I have often wondered about that, and the first person to mention it after yesterday’s post was Erin Stellato (twitter | blog): Before we go on to make sense of all this, let’s look at another example of how SQL Server confusingly mixes the terms ‘Scan’ and ‘Seek’ in different contexts.  The diagram below shows a very simple heap table with two columns, one of which is the non-clustered Primary Key, and the other has a non-unique non-clustered index defined on it.  The right hand side of the diagram shows a simple query, it’s associated query plan, and a couple of extracts from the SSMS tool-tip and Properties windows. Notice the ‘scan direction’ entry in the Properties window snippet.  Is this a seek or a scan?  The different references to Scans and Seeks are even more pronounced in the XML plan output that the graphical plan is based on.  This fragment is what lies behind the single Index Seek icon shown above: You’ll find the same confusing references to Seeks and Scans throughout the product and its documentation. Making Sense of Seeks Let’s forget all about scans for a moment, and think purely about seeks.  Loosely speaking, a seek is the process of navigating an index B-tree to find a particular index record, most often at the leaf level.  A seek starts at the root and navigates down through the levels of the index to find the point of interest: Singleton Lookups The simplest sort of seek predicate performs this traversal to find (at most) a single record.  This is the case when we search for a single value using a unique index and an equality predicate.  It should be readily apparent that this type of search will either find one record, or none at all.  This operation is known as a singleton lookup.  Given the example table from before, the following query is an example of a singleton lookup seek: Sadly, there’s nothing in the graphical plan or XML output to show that this is a singleton lookup – you have to infer it from the fact that this is a single-value equality seek on a unique index.  The other common examples of a singleton lookup are bookmark lookups – both the RID and Key Lookup forms are singleton lookups (an RID lookup finds a single record in a heap from the unique row locator, and a Key Lookup does much the same thing on a clustered table).  If you happen to run your query with STATISTICS IO ON, you will notice that ‘Scan Count’ is always zero for a singleton lookup. Range Scans The other type of seek predicate is a ‘seek plus range scan’, which I will refer to simply as a range scan.  The seek operation makes an initial descent into the index structure to find the first leaf row that qualifies, and then performs a range scan (either backwards or forwards in the index) until it reaches the end of the scan range. The ability of a range scan to proceed in either direction comes about because index pages at the same level are connected by a doubly-linked list – each page has a pointer to the previous page (in logical key order) as well as a pointer to the following page.  The doubly-linked list is represented by the green and red dotted arrows in the index diagram presented earlier.  One subtle (but important) point is that the notion of a ‘forward’ or ‘backward’ scan applies to the logical key order defined when the index was built.  In the present case, the non-clustered primary key index was created as follows: CREATE TABLE dbo.Example ( key_col INTEGER NOT NULL, data INTEGER NOT NULL, CONSTRAINT [PK dbo.Example key_col] PRIMARY KEY NONCLUSTERED (key_col ASC) ) ; Notice that the primary key index specifies an ascending sort order for the single key column.  This means that a forward scan of the index will retrieve keys in ascending order, while a backward scan would retrieve keys in descending key order.  If the index had been created instead on key_col DESC, a forward scan would retrieve keys in descending order, and a backward scan would return keys in ascending order. A range scan seek predicate may have a Start condition, an End condition, or both.  Where one is missing, the scan starts (or ends) at one extreme end of the index, depending on the scan direction.  Some examples might help clarify that: the following diagram shows four queries, each of which performs a single seek against a column holding every integer from 1 to 100 inclusive.  The results from each query are shown in the blue columns, and relevant attributes from the Properties window appear on the right: Query 1 specifies that all key_col values less than 5 should be returned in ascending order.  The query plan achieves this by seeking to the start of the index leaf (there is no explicit starting value) and scanning forward until the End condition (key_col < 5) is no longer satisfied (SQL Server knows it can stop looking as soon as it finds a key_col value that isn’t less than 5 because all later index entries are guaranteed to sort higher). Query 2 asks for key_col values greater than 95, in descending order.  SQL Server returns these results by seeking to the end of the index, and scanning backwards (in descending key order) until it comes across a row that isn’t greater than 95.  Sharp-eyed readers may notice that the end-of-scan condition is shown as a Start range value.  This is a bug in the XML show plan which bubbles up to the Properties window – when a backward scan is performed, the roles of the Start and End values are reversed, but the plan does not reflect that.  Oh well. Query 3 looks for key_col values that are greater than or equal to 10, and less than 15, in ascending order.  This time, SQL Server seeks to the first index record that matches the Start condition (key_col >= 10) and then scans forward through the leaf pages until the End condition (key_col < 15) is no longer met. Query 4 performs much the same sort of operation as Query 3, but requests the output in descending order.  Again, we have to mentally reverse the Start and End conditions because of the bug, but otherwise the process is the same as always: SQL Server finds the highest-sorting record that meets the condition ‘key_col < 25’ and scans backward until ‘key_col >= 20’ is no longer true. One final point to note: seek operations always have the Ordered: True attribute.  This means that the operator always produces rows in a sorted order, either ascending or descending depending on how the index was defined, and whether the scan part of the operation is forward or backward.  You cannot rely on this sort order in your queries of course (you must always specify an ORDER BY clause if order is important) but SQL Server can make use of the sort order internally.  In the four queries above, the query optimizer was able to avoid an explicit Sort operator to honour the ORDER BY clause, for example. Multiple Seek Predicates As we saw yesterday, a single index seek plan operator can contain one or more seek predicates.  These seek predicates can either be all singleton seeks or all range scans – SQL Server does not mix them.  For example, you might expect the following query to contain two seek predicates, a singleton seek to find the single record in the unique index where key_col = 10, and a range scan to find the key_col values between 15 and 20: SELECT key_col FROM dbo.Example WHERE key_col = 10 OR key_col BETWEEN 15 AND 20 ORDER BY key_col ASC ; In fact, SQL Server transforms the singleton seek (key_col = 10) to the equivalent range scan, Start:[key_col >= 10], End:[key_col <= 10].  This allows both range scans to be evaluated by a single seek operator.  To be clear, this query results in two range scans: one from 10 to 10, and one from 15 to 20. Final Thoughts That’s it for today – tomorrow we’ll look at monitoring singleton lookups and range scans, and I’ll show you a seek on a heap table. Yes, a seek.  On a heap.  Not an index! If you would like to run the queries in this post for yourself, there’s a script below.  Thanks for reading! IF OBJECT_ID(N'dbo.Example', N'U') IS NOT NULL BEGIN DROP TABLE dbo.Example; END ; -- Test table is a heap -- Non-clustered primary key on 'key_col' CREATE TABLE dbo.Example ( key_col INTEGER NOT NULL, data INTEGER NOT NULL, CONSTRAINT [PK dbo.Example key_col] PRIMARY KEY NONCLUSTERED (key_col) ) ; -- Non-unique non-clustered index on the 'data' column CREATE NONCLUSTERED INDEX [IX dbo.Example data] ON dbo.Example (data) ; -- Add 100 rows INSERT dbo.Example WITH (TABLOCKX) ( key_col, data ) SELECT key_col = V.number, data = V.number FROM master.dbo.spt_values AS V WHERE V.[type] = N'P' AND V.number BETWEEN 1 AND 100 ; -- ================ -- Singleton lookup -- ================ ; -- Single value equality seek in a unique index -- Scan count = 0 when STATISTIS IO is ON -- Check the XML SHOWPLAN SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col = 32 ; -- =========== -- Range Scans -- =========== ; -- Query 1 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col <= 5 ORDER BY E.key_col ASC ; -- Query 2 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col > 95 ORDER BY E.key_col DESC ; -- Query 3 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col >= 10 AND E.key_col < 15 ORDER BY E.key_col ASC ; -- Query 4 SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col >= 20 AND E.key_col < 25 ORDER BY E.key_col DESC ; -- Final query (singleton + range = 2 range scans) SELECT E.key_col FROM dbo.Example AS E WHERE E.key_col = 10 OR E.key_col BETWEEN 15 AND 20 ORDER BY E.key_col ASC ; -- === TIDY UP === DROP TABLE dbo.Example; © 2011 Paul White email: [email protected] twitter: @SQL_Kiwi

  Read the article

• How to deal with a poor team leader and a tester manager from hell? [closed]

  - by Google

  Let me begin by explaining my situation and give a little context to the situation. My company has around 15 developers but we're split up on two different areas. We have a fresh product team and the old product team. The old product team does mostly bug fixes/maintenance and a feature here and there. The fresh product had never been released and was new from the ground up. I am on the fresh product team. The team consists of three developers (myself, another developer and a senior developer). The senior is also our team leader. Our roles are as follows: Myself: building the administration client as well as build/release stuff Other dev: building the primary client Team lead: building the server In addition to the dev team, we interact with the test manager often. By "we" I mean me since I do the build stuff and give him the builds to test. Trial 1: The other developer on my team and I have both tried to talk to our manager about our team leader. About two weeks before release we went in his office and had a closed door meeting before our team lead got to work. We expressed our concerns about the product, its release date and our team leader. We expressed our team leader had a "rosey" image of the product's state. Our manager seemed to listen to what we said and thanked us for taking the initiative to speak with him about it. He got us an extra two weeks before release. The situation with the leader didn't change. In fact, it got a little worse. While we were using the two weeks to fix issues he was slacking off quite a bit. Just to name a few things, he installed Windows 8 on his dev machine during this time (claimed him machine was broke), he wrote a plugin for our office messenger that turned turned messages into speech, and one time when I went in his office he was making a 3D model in Blender (for "fun"). He felt the product was "pretty good" and ready for release. During this time I dealt with the test manager on a daily basis. Every bug or issue that popped up he would pretty much attack me personally (regardless of which component the bug was in). The test manager would often push his "views" of what needed to be done with the product. He virtually ordered me to change text on our installer and to add features to the installer and administration client. I tried to express how his suggestions were "valid ideas" but it was too close to release to do those kinds of things and to make matters worse, our technical writer had already finished documentation and such a change would not only affect the dev team but would affect the technical writer and marketing as well. I expressed I wasn't going to make those changes without marketing's consent as well as the technical writer and my manager's. He pretty much said I don't care about the product and said I don't do my job. I would like to take a moment to say I take my job seriously and I do my best. I am the kind of person that goes to work 30-40 mins early and usually leaves 30 minutes later than everyone else. Saying I don't care or do my job is just insulting. His "attacks" on me grew from day to day. Every bug that popped up he would usually comment on in some manner that jabbed me and the other developer. "Oh that bug! Yeah that should have been fixed by now, figures! If someone would do their job!" and other similar kinds of comments. Keep in mind 8 out of 10 bugs were in the server and had nothing to do with me and the other developer. That didn't seem to matter.. On one occasion they got pretty bad and we almost got into a yelling match so I decided to stop talking to him all together. I carried all communication through office email (with my manager cc'd). He never attacked me via email. He still attempted to get aggressive with me in person but I completely ignore him and my only response to any question is, "Ask my team leader." or "Ask a product manager." The product launched after our two week extension. Trial 2: The day after the product launch our team leader went on vacation (thanks....). At this time we got a lot of questions from the tech support... major issues with the product. All of these issues were bugs marked "resolved" by our lovely team leader (a typical situation that often popped up). This is where we currently are. The other developer has been with the company for about three years (I've been there only five months) and told me he was going to speak with our manager alone and hoped it would help get our concerns across a little better in a one-on-one. He spoke with the manager and directly addressed all of our concerns regarding our team leader and the test manager giving us (mostly me) hell. Our manager basically said he understood how hard we work and said he noticed it and there's no doubt about it. He said he spoke with the test manager about his temper. Regarding the team leader, he didn't say a whole lot. He suggested we sit down with the team leader and address our concerns (isn't that the manager's job?). We're still waiting to see if anything has changed but we doubt it. What can we do next? 1) Talk to the team leader (may stress relationship and make work awkward) I admit the team leader is generally a nice guy. He is just a horrible leader and working closely with him is painful. I still don't believe bringing this directly to the team leader would help at all and may negatively impact the situation. 2) I could quit. Other than this situation the job is pretty fantastic. I really like my other coworkers and we have quite a bit of freedom. 3) I could take the situation with the team leader to one of the owners. I would then be throwing my manager under the bus. 4) I could take the situation with the test manager to HR. Any suggestions? Comments?

  Read the article

• CDN on Hosted Service in Windows Azure

  - by Shaun

  Yesterday I told Wang Tao, an annoying colleague sitting beside me, about how to make the static content enable the CDN in his website which had just been published on Windows Azure. The approach would be Move the static content, the images, CSS files, etc. into the blob storage. Enable the CDN on his storage account. Change the URL of those static files to the CDN URL. I think these are the very common steps when using CDN. But this morning I found that the new Windows Azure SDK 1.4 and new Windows Azure Developer Portal had just been published announced at the Windows Azure Blog. One of the new features in this release is about the CDN, which means we can enabled the CDN not only for a storage account, but a hosted service as well. Within this new feature the steps I mentioned above would be turned simpler a lot.   Enable CDN for Hosted Service To enable the CDN for a hosted service we just need to log on the Windows Azure Developer Portal. Under the “Hosted Services, Storage Accounts & CDN” item we will find a new menu on the left hand side said “CDN”, where we can manage the CDN for storage account and hosted service. As we can see the hosted services and storage accounts are all listed in my subscriptions. To enable a CDN for a hosted service is veru simple, just select a hosted service and click the New Endpoint button on top. In this dialog we can select the subscription and the storage account, or the hosted service we want the CDN to be enabled. If we selected the hosted service, like I did in the image above, the “Source URL for the CDN endpoint” will be shown automatically. This means the windows azure platform will make all contents under the “/cdn” folder as CDN enabled. But we cannot change the value at the moment. The following 3 checkboxes next to the URL are: Enable CDN: Enable or disable the CDN. HTTPS: If we need to use HTTPS connections check it. Query String: If we are caching content from a hosted service and we are using query strings to specify the content to be retrieved, check it. Just click the “Create” button to let the windows azure create the CDN for our hosted service. The CDN would be available within 60 minutes as Microsoft mentioned. My experience is that about 15 minutes the CDN could be used and we can find the CDN URL in the portal as well.   Put the Content in CDN in Hosted Service Let’s create a simple windows azure project in Visual Studio with a MVC 2 Web Role. When we created the CDN mentioned above the source URL of CDN endpoint would be under the “/cdn” folder. So in the Visual Studio we create a folder under the website named “cdn” and put some static files there. Then all these files would be cached by CDN if we use the CDN endpoint. The CDN of the hosted service can cache some kind of “dynamic” result with the Query String feature enabled. We create a controller named CdnController and a GetNumber action in it. The routed URL of this controller would be /Cdn/GetNumber which can be CDN-ed as well since the URL said it’s under the “/cdn” folder. In the GetNumber action we just put a number value which specified by parameter into the view model, then the URL could be like /Cdn/GetNumber?number=2. 1: using System; 2: using System.Collections.Generic; 3: using System.Linq; 4: using System.Web; 5: using System.Web.Mvc; 6:  7: namespace MvcWebRole1.Controllers 8: { 9: public class CdnController : Controller 10: { 11: // 12: // GET: /Cdn/ 13:  14: public ActionResult GetNumber(int number) 15: { 16: return View(number); 17: } 18:  19: } 20: } And we add a view to display the number which is super simple. 1: <%@ Page Title="" Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<int>" %> 2:  3: <asp:Content ID="Content1" ContentPlaceHolderID="TitleContent" runat="server"> 4: GetNumber 5: </asp:Content> 6:  7: <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> 8:  9: <h2>The number is: <% 1: : Model.ToString() %></h2> 10:  11: </asp:Content> Since this action is under the CdnController the URL would be under the “/cdn” folder which means it can be CDN-ed. And since we checked the “Query String” the content of this dynamic page will be cached by its query string. So if I use the CDN URL, http://az25311.vo.msecnd.net/GetNumber?number=2, the CDN will firstly check if there’s any content cached with the key “GetNumber?number=2”. If yes then the CDN will return the content directly; otherwise it will connect to the hosted service, http://aurora-sys.cloudapp.net/Cdn/GetNumber?number=2, and then send the result back to the browser and cached in CDN. But to be notice that the query string are treated as string when used by the key of CDN element. This means the URLs below would be cached in 2 elements in CDN: http://az25311.vo.msecnd.net/GetNumber?number=2&page=1 http://az25311.vo.msecnd.net/GetNumber?page=1&number=2 The final step is to upload the project onto azure. Test the Hosted Service CDN After published the project on azure, we can use the CDN in the website. The CDN endpoint we had created is az25311.vo.msecnd.net so all files under the “/cdn” folder can be requested with it. Let’s have a try on the sample.htm and c_great_wall.jpg static files. Also we can request the dynamic page GetNumber with the query string with the CDN endpoint. And if we refresh this page it will be shown very quickly since the content comes from the CDN without MCV server side process. We style of this page was missing. This is because the CSS file was not includes in the “/cdn” folder so the page cannot retrieve the CSS file from the CDN URL.   Summary In this post I introduced the new feature in Windows Azure CDN with the release of Windows Azure SDK 1.4 and new Developer Portal. With the CDN of the Hosted Service we can just put the static resources under a “/cdn” folder so that the CDN can cache them automatically and no need to put then into the blob storage. Also it support caching the dynamic content with the Query String feature. So that we can cache some parts of the web page by using the UserController and CDN. For example we can cache the log on user control in the master page so that the log on part will be loaded super-fast. There are some other new features within this release you can find here. And for more detailed information about the Windows Azure CDN please have a look here as well.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

  Read the article

• Command line mode only -- successful login only brings me back to login screen

  - by seth

  whenever I log in the screen goes black, I see a glimpse of terminal-esque text, and then it brings me back to the log in screen (Ubuntu 12.04). I can enter and log in via the command line. The guest account works find. I think this happened because I edited some Xorg related file trying to make an external monitor work with my laptop. I copy pasted from a forum post so I dont recall the file or what i put in the file. Can't find the forum post again and my bash history wasn't recorded from that session. I tried reinstalling Xorg and ubuntu-desktop, nvidia, resetting any configs I could find... I'm really at a loss of what to do. Here's my /.xsession-errors: /usr/sbin/lightdm-session: 11: /home/seth/.profile: -s: not found Backend : gconf Integration : true Profile : unity Adding plugins Initializing core options...done Initializing composite options...done Initializing opengl options...done Initializing decor options...done Initializing vpswitch options...done Initializing snap options...done Initializing mousepoll options...done Initializing resize options...done Initializing place options...done Initializing move options...done Initializing wall options...done Initializing grid options...done I/O warning : failed to load external entity "/home/seth/.compiz/session/108fa6ea48f8a973b9133850948930576700000017740033" Initializing session options...done Initializing gnomecompat options...done ** Message: applet now removed from the notification area Initializing animation options...done Initializing fade options...done Initializing unitymtgrabhandles options...done Initializing workarounds options...done Initializing scale options...done compiz (expo) - Warn: failed to bind image to texture Initializing expo options...done Initializing ezoom options...done ** Message: using fallback from indicator to GtkStatusIcon (compiz:1846): GConf-CRITICAL **: gconf_client_add_dir: assertion `gconf_valid_key (dirname, NULL)' failed Initializing unityshell options...done Nautilus-Share-Message: Called "net usershare info" but it failed: 'net usershare' returned error 255: net usershare: cannot open usershare directory /var/lib/samba/usershares. Error No such file or directory Please ask your system administrator to enable user sharing. Setting Update "main_menu_key" Setting Update "run_key" Setting Update "launcher_hide_mode" Setting Update "edge_responsiveness" Setting Update "launcher_capture_mouse" ** Message: moving back from GtkStatusIcon to indicator compiz (decor) - Warn: failed to bind pixmap to texture ** (zeitgeist-datahub:2128): WARNING **: zeitgeist-datahub.vala:227: Unable to get name "org.gnome.zeitgeist.datahub" on the bus! failed to create drawable compiz (core) - Warn: glXCreatePixmap failed compiz (core) - Warn: Couldn't bind background pixmap 0x1e00001 to texture compiz (decor) - Warn: failed to bind pixmap to texture ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. compiz (decor) - Warn: failed to bind pixmap to texture compiz (decor) - Warn: failed to bind pixmap to texture ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. ** Message: No keyring secrets found for Sonic.net_356/802-11-wireless-security; asking user. [2348:2352:12678840568:ERROR:gpu_watchdog_thread.cc(231)] The GPU process hung. Terminating after 10000 ms. [2256:2283:14450711755:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14450726175:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14450746028:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14464521342:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14464541249:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14690775186:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14690795231:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14704543843:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14704566717:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14766138587:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14857232694:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14930901403:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14930965542:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14944566814:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:14944592215:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15170929788:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15170947382:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15184585015:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15184605475:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15366189036:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15410983381:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15411569689:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15431632431:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15431674438:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15457304356:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15656020938:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15656042383:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15674651268:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:15674671786:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:16052544301:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:16057387653:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:16157122849:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:16157123851:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:16157125473:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:16157126544:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 [2256:2283:16157129682:ERROR:ssl_client_socket_nss.cc(1542)] handshake with server mail.google.com:443 failed; NSS error code -5938, net_error -107 If anyone can help me out, I'd be forever grateful

  Read the article

• Making Sense of ASP.NET Paths

  - by Renso

  Making Sense of ASP.NET Paths ASP.Net includes quite a plethora of properties to retrieve path information about the current request, control and application. There's a ton of information available about paths on the Request object, some of it appearing to overlap and some of it buried several levels down, and it can be confusing to find just the right path that you are looking for. To keep things straight I thought it a good idea to summarize the path options along with descriptions and example paths. I wrote a post about this a long time ago in 2004 and I find myself frequently going back to that page to quickly figure out which path I’m looking for in processing the current URL. Apparently a lot of people must be doing the same, because the original post is the second most visited even to this date on this blog to the tune of nearly 500 hits per day. So, I decided to update and expand a bit on the original post with a little more information and clarification based on the original comments. Request Object Paths Available Here's a list of the Path related properties on the Request object (and the Page object). Assume a path like http://www.west-wind.com/webstore/admin/paths.aspx for the paths below where webstore is the name of the virtual. Request Property Description and Value ApplicationPath Returns the web root-relative logical path to the virtual root of this app. /webstore/ PhysicalApplicationPath Returns local file system path of the virtual root for this app. c:\inetpub\wwwroot\webstore PhysicalPath Returns the local file system path to the current script or path. c:\inetpub\wwwroot\webstore\admin\paths.aspx Path FilePath CurrentExecutionFilePath All of these return the full root relative logical path to the script page including path and scriptname. CurrentExcecutionFilePath will return the ‘current’ request path after a Transfer/Execute call while FilePath will always return the original request’s path. /webstore/admin/paths.aspx AppRelativeCurrentExecutionFilePath Returns an ASP.NET root relative virtual path to the script or path for the current request. If in  a Transfer/Execute call the transferred Path is returned. ~/admin/paths.aspx PathInfo Returns any extra path following the script name. If no extra path is provided returns the root-relative path (returns text in red below). string.Empty if no PathInfo is available. /webstore/admin/paths.aspx/ExtraPathInfo RawUrl Returns the full root relative URL including querystring and extra path as a string. /webstore/admin/paths.aspx?sku=wwhelp40 Url Returns a fully qualified URL including querystring and extra path. Note this is a Uri instance rather than string. http://www.west-wind.com/webstore/admin/paths.aspx?sku=wwhelp40 UrlReferrer The fully qualified URL of the page that sent the request. This is also a Uri instance and this value is null if the page was directly accessed by typing into the address bar or using an HttpClient based Referrer client Http header. http://www.west-wind.com/webstore/default.aspx?Info Control.TemplateSourceDirectory Returns the logical path to the folder of the page, master or user control on which it is called. This is useful if you need to know the path only to a Page or control from within the control. For non-file controls this returns the Page path. /webstore/admin/ As you can see there’s a ton of information available there for each of the three common path formats: Physical Path is an OS type path that points to a path or file on disk. Logical Path is a Web path that is relative to the Web server’s root. It includes the virtual plus the application relative path. ~/ (Root-relative) Path is an ASP.NET specific path that includes ~/ to indicate the virtual root Web path. ASP.NET can convert virtual paths into either logical paths using Control.ResolveUrl(), or physical paths using Server.MapPath(). Root relative paths are useful for specifying portable URLs that don’t rely on relative directory structures and very useful from within control or component code. You should be able to get any necessary format from ASP.NET from just about any path or script using these mechanisms. ~/ Root Relative Paths and ResolveUrl() and ResolveClientUrl() ASP.NET supports root-relative virtual path syntax in most of its URL properties in Web Forms. So you can easily specify a root relative path in a control rather than a location relative path: <asp:Image runat="server" ID="imgHelp" ImageUrl="~/images/help.gif" /> ASP.NET internally resolves this URL by using ResolveUrl("~/images/help.gif") to arrive at the root-relative URL of /webstore/images/help.gif which uses the Request.ApplicationPath as the basepath to replace the ~. By convention any custom Web controls also should use ResolveUrl() on URL properties to provide the same functionality. In your own code you can use Page.ResolveUrl() or Control.ResolveUrl() to accomplish the same thing: string imgPath = this.ResolveUrl("~/images/help.gif"); imgHelp.ImageUrl = imgPath; Unfortunately ResolveUrl() is limited to WebForm pages, so if you’re in an HttpHandler or Module it’s not available. ASP.NET Mvc also has it’s own more generic version of ResolveUrl in Url.Decode: <script src="<%= Url.Content("~/scripts/new.js") %>" type="text/javascript"></script> which is part of the UrlHelper class. In ASP.NET MVC the above sort of syntax is actually even more crucial than in WebForms due to the fact that views are not referencing specific pages but rather are often path based which can lead to various variations on how a particular view is referenced. In a Module or Handler code Control.ResolveUrl() unfortunately is not available which in retrospect seems like an odd design choice – URL resolution really should happen on a Request basis not as part of the Page framework. Luckily you can also rely on the static VirtualPathUtility class: string path = VirtualPathUtility.ToAbsolute("~/admin/paths.aspx"); VirtualPathUtility also many other quite useful methods for dealing with paths and converting between the various kinds of paths supported. One thing to watch out for is that ToAbsolute() will throw an exception if a query string is provided and doesn’t work on fully qualified URLs. I wrote about this topic with a custom solution that works fully qualified URLs and query strings here (check comments for some interesting discussions too). Similar to ResolveUrl() is ResolveClientUrl() which creates a fully qualified HTTP path that includes the protocol and domain name. It’s rare that this full resolution is needed but can be useful in some scenarios. Mapping Virtual Paths to Physical Paths with Server.MapPath() If you need to map root relative or current folder relative URLs to physical URLs or you can use HttpContext.Current.Server.MapPath(). Inside of a Page you can do the following: string physicalPath = Server.MapPath("~/scripts/ww.jquery.js")); MapPath is pretty flexible and it understands both ASP.NET style virtual paths as well as plain relative paths, so the following also works. string physicalPath = Server.MapPath("scripts/silverlight.js"); as well as dot relative syntax: string physicalPath = Server.MapPath("../scripts/jquery.js"); Once you have the physical path you can perform standard System.IO Path and File operations on the file. Remember with physical paths and IO or copy operations you need to make sure you have permissions to access files and folders based on the Web server user account that is active (NETWORK SERVICE, ASPNET typically). Note the Server.MapPath will not map up beyond the virtual root of the application for security reasons. Server and Host Information Between these settings you can get all the information you may need to figure out where you are at and to build new Url if necessary. If you need to build a URL completely from scratch you can get access to information about the server you are accessing: Server Variable Function and Example SERVER_NAME The of the domain or IP Address wwww.west-wind.com or 127.0.0.1 SERVER_PORT The port that the request runs under. 80 SERVER_PORT_SECURE Determines whether https: was used. 0 or 1 APPL_MD_PATH ADSI DirectoryServices path to the virtual root directory. Note that LM typically doesn’t work for ADSI access so you should replace that with LOCALHOST or the machine’s NetBios name. /LM/W3SVC/1/ROOT/webstore Request.Url and Uri Parsing If you still need more control over the current request URL or  you need to create new URLs from an existing one, the current Request.Url Uri property offers a lot of control. Using the Uri class and UriBuilder makes it easy to retrieve parts of a URL and create new URLs based on existing URL. The UriBuilder class is the preferred way to create URLs – much preferable over creating URIs via string concatenation. Uri Property Function Scheme The URL scheme or protocol prefix. http or https Port The port if specifically specified. DnsSafeHost The domain name or local host NetBios machine name www.west-wind.com or rasnote LocalPath The full path of the URL including script name and extra PathInfo. /webstore/admin/paths.aspx Query The query string if any ?id=1 The Uri class itself is great for retrieving Uri parts, but most of the properties are read only if you need to modify a URL in order to change it you can use the UriBuilder class to load up an existing URL and modify it to create a new one. Here are a few common operations I’ve needed to do to get specific URLs: Convert the Request URL to an SSL/HTTPS link For example to take the current request URL and converted  it to a secure URL can be done like this: UriBuilder build = new UriBuilder(Request.Url); build.Scheme = "https"; build.Port = -1; // don't inject portUri newUri = build.Uri; string newUrl = build.ToString(); Retrieve the fully qualified URL without a QueryString AFAIK, there’s no native routine to retrieve the current request URL without the query string. It’s easy to do with UriBuilder however: UriBuilder builder = newUriBuilder(Request.Url); builder.Query = ""; stringlogicalPathWithoutQuery = builder.ToString();

  Read the article

• All downloads being interrupted

  - by Jake

  System: Windows 7 Professional 64bit. 8GB RAM, Intel i5-2400 CPU, +300GB free on the hard drive. AVG Internet Security 2012 (enabled & disabled, with firewall enabled and disabled - no effect for either). This computer is less than a year old. Network: This problem is occurring on a single computer on a network with multiple computers. The router is a Motorola Netopia 3347-02 (DSL Modem/Wireless Router combined). The computer is plugged in directly to the modem, other computers are using the wireless successfully. The router has been reset. The only thing odd about the connection between the router and computer is that it is configured to allow RDP through, so it is assigned a static IP by the router and port forwarding is enabled for port 3389. Also, though I doubt it matters, a second wireless router is active behind this router providing a second network that some computers in the area use without issues. Details: All downloads initiated on this specific computer eventually fail, this includes streaming from youtube, specialized downloads (itunes), downloads from websites, FTP downloads, etc. Failure occurs with all browsers, but in chrome this is the process it takes: 1) Download begins normally, 2) At some point between (observed) 7MBs and 229MBs the download stops progressing (at this point, if watching chrome's task manager, you can see the network activity for the downloading tab drop to 0kps), 3) for some time the download sits there still attempting to complete, but will eventually display "123,049,871/0 B, Interrupted" (where the number is whatever it actually got to). The file I am using to test this is a very large .zip file located on a server I control, but the problem seems to occur on any site. The amount downloaded is completely random, and seems to be more time-based than anything (if I start a download immediately after the last one fails, it tends to get further than the last one). Small files can get through for this reason, though they can fail as well. In a test where I simultaneously downloaded the same file via HTTP (chrome) and FTP (windows explorer), both downloads failed at the same instant, though explorer displayed "Connection timed out" several minutes before chrome finally showed the download as interrupted. Other things I have tried based on advice given to people with similar/identical problems: Setting my MTU to 1492 (as described here: http://blog.thecompwiz.com/2011/08/networking-issues.html) Disabling write caching to the hard drive storing the download on an external device successfully transmitted +1GB file from one computer on the same network to this computer disabling indexing in the folder the download was being stored in disabling all security software checked to make sure all drivers were up to date read about 50 accounts with nearly exact descriptions of what I'm experiencing, none of which had a solution given Running Processes: Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 104,836 K smss.exe 332 Services 0 1,276 K csrss.exe 764 Services 0 5,060 K wininit.exe 820 Services 0 4,748 K csrss.exe 844 Console 1 23,764 K services.exe 876 Services 0 11,856 K lsass.exe 892 Services 0 14,420 K lsm.exe 900 Services 0 7,820 K winlogon.exe 944 Console 1 7,716 K svchost.exe 428 Services 0 12,744 K svchost.exe 796 Services 0 12,240 K svchost.exe 1036 Services 0 22,372 K svchost.exe 1084 Services 0 174,132 K svchost.exe 1112 Services 0 56,144 K svchost.exe 1288 Services 0 18,640 K svchost.exe 1404 Services 0 29,616 K spoolsv.exe 1576 Services 0 25,924 K svchost.exe 1616 Services 0 12,788 K AppleMobileDeviceService. 1728 Services 0 9,796 K avgwdsvc.exe 1820 Services 0 8,268 K mDNSResponder.exe 1844 Services 0 5,832 K w3dbsmgr.exe 1108 Services 0 43,760 K QBCFMonitorService.exe 1336 Services 0 16,408 K svchost.exe 2404 Services 0 28,240 K taskhost.exe 3020 Console 1 12,372 K dwm.exe 2280 Console 1 5,968 K explorer.exe 2964 Console 1 152,476 K WUDFHost.exe 3316 Services 0 6,740 K svchost.exe 3408 Services 0 5,556 K RAVCpl64.exe 3684 Console 1 13,864 K igfxtray.exe 3700 Console 1 7,804 K hkcmd.exe 3772 Console 1 7,868 K igfxpers.exe 3788 Console 1 10,940 K sidebar.exe 3836 Console 1 84,400 K chrome.exe 3964 Console 1 19,640 K pptd40nt.exe 4068 Console 1 5,156 K acrotray.exe 3908 Console 1 14,676 K avgtray.exe 3872 Console 1 9,508 K jusched.exe 4076 Console 1 4,412 K iTunesHelper.exe 1532 Console 1 87,308 K SearchIndexer.exe 3492 Services 0 36,948 K iPodService.exe 4136 Services 0 7,944 K BrccMCtl.exe 4276 Console 1 18,132 K splwow64.exe 4380 Console 1 32,600 K qbupdate.exe 4836 Console 1 24,236 K svchost.exe 4288 Services 0 20,700 K wmpnetwk.exe 3112 Services 0 9,516 K FNPLicensingService.exe 5248 Services 0 5,852 K QBW32.EXE 5508 Console 1 127,068 K QBDBMgrN.exe 5600 Services 0 42,252 K EXCEL.EXE 2512 Console 1 99,100 K LMS.exe 3188 Services 0 5,616 K UNS.exe 1600 Services 0 7,308 K axlbridge.exe 5260 Console 1 5,132 K chrome.exe 5888 Console 1 200,336 K chrome.exe 3536 Console 1 26,076 K chrome.exe 1952 Console 1 20,168 K chrome.exe 4596 Console 1 24,696 K chrome.exe 4292 Console 1 48,096 K chrome.exe 2796 Console 1 23,520 K Acrobat.exe 1240 Console 1 87,252 K 123w.exe 4892 Console 1 22,728 K calc.exe 1700 Console 1 12,636 K chrome.exe 1328 Console 1 28,888 K chrome.exe 3696 Console 1 47,012 K rundll32.exe 6320 Console 1 7,104 K chrome.exe 4928 Console 1 44,248 K AVGIDSAgent.exe 260 Services 0 12,940 K avgfws.exe 6052 Services 0 26,912 K avgnsa.exe 5064 Services 0 2,496 K avgrsa.exe 3088 Services 0 2,200 K avgcsrva.exe 2596 Services 0 380 K avgcsrva.exe 6948 Services 0 408 K StikyNot.exe 452 Console 1 14,772 K chrome.exe 4580 Console 1 28,200 K chrome.exe 4016 Console 1 57,756 K svchost.exe 7140 Services 0 4,500 K chrome.exe 6264 Console 1 56,824 K chrome.exe 7008 Console 1 56,896 K chrome.exe 2224 Console 1 38,032 K taskhost.exe 612 Console 1 7,228 K chrome.exe 6000 Console 1 10,928 K chrome.exe 2568 Console 1 43,052 K chrome.exe 272 Console 1 75,988 K chrome.exe 7328 Console 1 53,240 K PaprPort.exe 7976 Console 1 137,152 K pplinks.exe 7500 Console 1 14,052 K ppscanmg.exe 5744 Console 1 18,996 K taskeng.exe 7388 Console 1 6,308 K SearchProtocolHost.exe 8024 Services 0 8,804 K SearchFilterHost.exe 7232 Services 0 7,848 K chrome.exe 8016 Console 1 37,440 K cmd.exe 7692 Console 1 3,096 K conhost.exe 7516 Console 1 5,872 K tasklist.exe 8160 Console 1 5,772 K WmiPrvSE.exe 7684 Services 0 6,400 K Any help with this would be greatly appreciated, I've been beating my head against a wall over this all day. This computer serves dual purpose as the main company document server and the Owner's work computer, it's fairly important it be fully functional and I cannot figure this out.

  Read the article

• CodePlex Daily Summary for Tuesday, April 27, 2010

  CodePlex Daily Summary for Tuesday, April 27, 2010New ProjectsActive Directory User Properties Change: A complete application in VS 2005 and VB.NET, for Request Request in User Details in Active Directory, with flow to HR and then to IT for approval ...AVR Terminal: A Windows application for connecting to an AVR via RS232 serial or USB-to-COM FTDI ports. Works on Arduino, Bare Bones Board, and any custom board...Battle Droids: AVR-based Network Combat!: A Battle Droid is an AVR® microcontroller running the BattleDroid firmware. This firmware turns your AVR into a lean, mean, fighting machine, and ...Camp Foundation: Camp Foundationchakma: chakma is a question - answer based web application to make people get questions from anybody around the world and being able to answer them. c...Document.Editor: Document.Editor is a multitab text editor for Windows. It includes plain and rich text format support, multi tab interface so you can edit multiple...Dot Net Marche Music Store Demo Application: This is a demo application that the DotNetMarche user gorup (www.dotnetmarche.org) use to make experiments and prepare demos for our workshopselivators: a monitor which enables the user to view the movement of the elivators in a buildingExtended SSIS Package Execute: The SSIS package execute task is flawed as it does not support passing variables. Here we have a custom task that will pass items in a dataflow as...File tools: File toolsFileExplorer.NET: FileExplorer.NET is a .net usercontrol which tries to mimic the Windows FileExplorer treeview.Kazuku: ASP.NET MVC 2 Content Management SystemKSharp Ajax Control Toolkit Library: Built ontop of the Microsoft ASP.NET Ajax Control Toolkit, this library offers enhanced versions of the controls found in the Ajax Control Toolkit....Nitrous - An Aspx ViewEngine for ASP.NET MVC: Near drop-in replacement ASP.NET ViewEngine for MVC.Open Data Protocol - Client Libraries: This is an Open Source release of the .NET and Silverlight Client Libraries for the Open Data Protocol (OData). For more information on odata, see ...ORAYLIS BI.SmartDiff: BI.SmartDiff is a helper to connect the functionality of BIDS Helper – SmartDiff to TortoiseSVN. BIDS Helper – SmartDiff helps you to get more read...RicciWebSiteSystem: soon websiteSynapse:Silverlight A Simple Silverlight Framework: Synapse:Silverlight is a simplified framework for Silverlight. It's purpose is to help developers and designers produce basic LOB solutions that do...TestProjectMB: Testing Team Foundation ServerThoughtWorks Cruise Notification Interceptor: Cruise notification interceptorThreadSafeControls: ThreadSafeControls is a C# project that greatly simplifies the process of transitioning Windows Forms applications to a multithreaded environment b...Unscrambler: Unscrambler is a multitouch WPF word game built with MVVM Light in order to show how to use the touch maniupation and inertia features included in ...Web Utilities: web utilitiesNew Releases7zbackup - PowerShell Script to Backup Files with 7zip: 7zBackup v. 1.7.1 Stable: Bug Solved : Presence of junction.exe is wrongly referred to 7z.exeAVR Terminal: AVR Terminal v0.2: Here is an Alpha-almost-BETA release of the AVR Terminal. That being said, I use it almost daily and it shouldn't break anything on your system, b...Bistro FSharp Extensions: 0.9.7.0: This is the VS 2010 release of BistroFS extensions. This release focused on usability, adding key functionality such as resource aliasing and secur...Bojinx: Bojinx Dialog Management V1.0: Stable release of the Bojinx Dialog Management library.BOWIE: BOWIE 2010: This new version works on Outlook 2007/2010 and TFS 2008/2010 RTM. Details about all features in this version on the Home Page : http://bowie.code...Catharsis: Catharsis 2.5 on catarsa.com: The Catharsis framework has finally its own portal http://catarsa.com Example - documented steps to create Web-Application http://catarsa.com/Arti...Colorful Expression: Expression Blend 3: Alpha Version, Read Issues and Installing! Colorful Expression is an add-in for Expression Blend and Expression Design that brings you the Adobe K...Colorful Expression: Expression Blend 4: Read Issues and Installing! Colorful Expression is an add-in for Expression Blend and Expression Design that brings you the Adobe Kuler and ColorLo...Courier: Version 1.0: This release includes integration with the Reactive Framework for more elegant message handling and allowing more succinct client code. Full suite...CRM 4.0 Contract Utilities: Release 1.0: Project Description List of Contract Utilities (i.e. custom workflow actions) 1. Change contract status from Active to Draft 2. Copy Contract (with...Document.Editor: 0.9.0: Whats New?: New icon set Bug fix'sDotNetNuke® Blog: 04.00.00: Minimum Required DNN Version: 4.06.02General Code organization * Converted project to .NET 3.5 * Converted solution to Visual Stud...EPiAbstractions: EPiAbstractions 1.2: Updated for EPiServer CMS 6. Only features abstractions for EPiServer CMS. For abstractions for EPiServer.Common and EPiServer.Community use versio...Fluent ViewModel Configuration for WPF (MVVM): FluentViewModel Alpha2: Added support for view model validation using FluentValidation (http://fluentvalidation.codeplex.com/) Fixed exception from Blend while in design...GArphics: Beta v0.9: Beta v0.9. Practically all of the planned features have been implemented and are available to the users. For the version 1.0 mainly just some minor...HTML Ruby: 6.22.2.1: Fixed a bug where HTML Ruby's options window will generate entries in the error log when applying option changes (regression from 6.21.8)HTML Ruby: 6.22.3: Add/remove stop spacing event listener as needed for possible fix to 4620iTuner - The iTunes Companion: iTuner 1.2.3768 Beta 3b: Beta 3 requires iTunes 9.1.0.79 or later A Librarian status panel showing active and queued Librarian scanners. This will be hidden behind the "bi...LiveUpload to Facebook: LiveUpload to Facebook 3.2.3: Version 3.2.3Become a fan on Facebook! Features Quickly and easily upload your photos and videos to Facebook, including any people tags added in W...Maintainance Schedule: Maintenance Scheduler: The first Alpha release of the project.NetSockets: NetSockets (1.2): The NetSockets library (DLL)NSIS Autorun: NSIS Autorun 0.1.2: NSIS Autorun 0.1.1 This release includes source code, application binary, and example materials.OpenSceneGraph glsl samples: OsgGlslSamples Win32 binaries: Project binary release for Windows. The effects shown are: Ambient Occlusion, Depth of Field, DoF with alpha channel, Fire effects, HDR, Light Ma...ORAYLIS BI.SmartDiff: ORAYLIS BI.SmartDiff 0.6.1: First public versionpatterns & practices - Windows Azure Guidance: Code Drop 4 - Content Complete: This release includes documentation and all code samples intended for this first guide. As before, this code release builds on the previous one an...Pex Custom Arithmetic Solver: Custom Solver Package: This is the custom solvers packaged together. To use simply include the dll in your project and add [assembly: PexCustomArithmeticSolver] to your P...PokeIn Comet Ajax Library: PokeIn v08 x86: New FeatureFrom this version forward, PokeIn will define a way between the main page and client side automaticly based to security level. Add "pub...Proxi [Proxy Interface]: Proxi Release 1.0.0.426: Proxi Release 1.0.0.426QuestTracker: QuestTracker 0.3: This release includes recurring quests! Now you can set a quest to uncomplete itself every X minutes, hours, or days! And the quests still retain t...Rensea Image Viewer: RIV 0.4.5: RIV Fix Version. You would need .NET Framework 4.0 to make it run RIVU Improved Version. With separated RIV up-loader, to upload images to Renjian...SCC Switch Provider: Provides a GUI to Switch Source Code Control Provi: Transferred from GotDotNet Workplace. Initial public Release. Downloaded ~922 times from original post.sTASKedit: sTASKedit v0.7a (Alpha): + Fixed: XOR text encoding + Fixed: adding timed rewards missing values + Fixed: occupations in clone()Synapse:Silverlight A Simple Silverlight Framework: Synapse Silverlight Alpha Release: Initial Road-map is being defined.ThoughtWorks Cruise Notification Interceptor: 1.0.0: Initial release.UDC indexes parser: UDC indexex parser Beta 2: Добавлена возможность работать с распределением определителей как если бы генератор был бы LALR(2) То что осталось: Если текстовое дополнение начи...Unscrambler: Release 1.0: Here's the first release of Unscrambler.WinXound: WinXound 3.3.0 Beta 2 for Mac OsX: New: Code Repository (for UDO and personal code) New: Format Code - Added the ability to format only the selected text of the code New: Explore...WPF Inspirational Quote Management System: Release 1.2.2: - Fixed issue some users were having when the application is minimised.Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitSilverlight Toolkitpatterns & practices – Enterprise LibraryMicrosoft SQL Server Product Samples: DatabaseWindows Presentation Foundation (WPF)ASP.NETMicrosoft SQL Server Community & SamplesPHPExcelMost Active Projectspatterns & practices – Enterprise LibraryRawrGMap.NET - Great Maps for Windows Forms & PresentationParticle Plot PivotBlogEngine.NETNB_Store - Free DotNetNuke Ecommerce Catalog ModuleFarseer Physics EngineIonics Isapi Rewrite FilterN2 CMSDotNetZip Library

  Read the article

• localhost/phpmyadmin pulls blank page

  - by Atul Modi

  When I tried configuring local machine as a Internet Gateway with website development capabilities over it and I installed all required software into it. I also had disable the selinux into it. But PROBLEM is when I do http://localhost/phpMyAdmin or all lower case than the page shows it as a blank page. I am pasting code from httpd.conf file into this as well as from phpMyAdmin.conf file I am using Fedora 16 for this. httpd.conf ServerTokens OS ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 60 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 5 StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 StartServers 4 MaxClients 300 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 Listen 80 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authn_dbd_module modules/mod_authn_dbd.so LoadModule dbd_module modules/mod_dbd.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule status_module modules/mod_status.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule info_module modules/mod_info.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule userdir_module modules/mod_userdir.so LoadModule alias_module modules/mod_alias.so LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_ajp_module modules/mod_proxy_ajp.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so Include conf.d/*.conf User apache Group apache ServerAdmin root@localhost UseCanonicalName Off DocumentRoot "/var/www/html" Options FollowSymLinks AllowOverride None Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all UserDir disabled DirectoryIndex index.html index.htm index.php AccessFileName .htaccess Order allow,deny Deny from all Satisfy All TypesConfig /etc/mime.types DefaultType text/plain MIMEMagicFile conf/magic HostnameLookups Off ErrorLog logs/error_log LogLevel warn LogFormat "%h %l %u %t \"%r\" %s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %s %b" common LogFormat "%{Referer}i - %U" referer LogFormat "%{User-agent}i" agent CustomLog logs/access_log combined ServerSignature On Alias /icons/ "/var/www/icons/" Options Indexes MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all # Location of the WebDAV lock database. DAVLockDB /var/lib/dav/lockdb ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" AllowOverride None Options None Order allow,deny Allow from all IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable Charset=UTF-8 AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ DefaultIcon /icons/unknown.gif ReadmeName README.html HeaderName HEADER.html IndexIgnore .??* *~ # HEADER README* RCS CVS *,v *,t AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw LanguagePriority en ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv zh-CN zh-TW ForceLanguagePriority Prefer Fallback AddDefaultCharset UTF-8 AddType application/x-tar .tgz AddType application/x-httpd-php .php AddType application/x-httpd-php .xml AddHandler application/x-httpd-php .xml AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddType application/x-x509-ca-cert .crt AddType application/x-pkcs7-crl .crl AddHandler type-map var AddType text/html .shtml AddOutputFilter INCLUDES .shtml Alias /error/ "/var/www/error/" AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en ForceLanguagePriority Prefer Fallback ErrorDocument 400 /error/HTTP_BAD_REQUEST.html.var ErrorDocument 401 /error/HTTP_UNAUTHORIZED.html.var ErrorDocument 403 /error/HTTP_FORBIDDEN.html.var ErrorDocument 404 /error/HTTP_NOT_FOUND.html.var ErrorDocument 405 /error/HTTP_METHOD_NOT_ALLOWED.html.var ErrorDocument 408 /error/HTTP_REQUEST_TIME_OUT.html.var ErrorDocument 500 /error/HTTP_INTERNAL_SERVER_ERROR.html.var ErrorDocument 503 /error/HTTP_SERVICE_UNAVAILABLE.html.var BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4.0" force-response-1.0 BrowserMatch "Java/1.0" force-response-1.0 BrowserMatch "JDK/1.0" force-response-1.0 BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully Order allow,deny Allow from all # phpMyAdmin.conf Alias /phpMyAdmin /usr/share/phpMyAdmin Alias /phpmyadmin /usr/share/phpMyAdmin Order Allow,Deny Allow from All Allow from 127.0.0.1 Allow from ::1 Order Allow,Deny Allow from All Allow from 127.0.0.1 Allow from ::1 Order Deny,Allow Deny from All Allow from None Order Deny,Allow Deny from All Allow from None Order Deny,Allow Deny from All Allow from None Can anyone help into this area please. Urgent reply will be appreciatable because i am struggling since one and half month for this matter. thank you, Atul

  Read the article

• CodePlex Daily Summary for Wednesday, May 05, 2010

  CodePlex Daily Summary for Wednesday, May 05, 2010New Projects2010微软精英大挑战Heritage of Dragon项目: 我们来自上海市同济大学，兴趣相投，集聚于此共同构建一个开放的网络平台。致力于运用构建在云端基于地图的服务，使用文字、图片、视频、互动动画等形式来展示全国各地的传统手工艺。并且充分发挥网络的优势，通过开放协作的维基平台人人都可以参与到内容的添加修改与完善中来。目的在于记录、展示、挖掘、传承中国古...AutoArchive: Auto archive your "my documents" to a remote machine. I'm writing this so my wife can put things in "my documents" and it'll automaticly archive i...BigDoor .NET Client: A .NET client for the BigDoor Media API. The API enables secured virtual transactions with support for any number of currencies, transactions, awar...bubujie: Dreamweaver LibraryGeckoGit: GeckoGit is a combination of TortoiseSVN and AnkhSVN, but for Git repositories, and built on the GitSharp library.Global: global, config, mail, http, rest, xml, serialization, helper, path, ioIndustrial Dashboard Connected Grid webpart: This Sharepoint 2007/10 webpart provides a simple way to display grid based reports populated with data that comes from a SQL Server stored procedu...IpControls: "IpControls" contains IPv4 and IPv6 text boxes, both as Windows Forms and WPF version. The IPv6 control automatically detects the older hybrid for...LiteME: LiteME is short for LiteMapleStoryEmulator... it is v75, open-source, and still going through it's alpha stages. It is still in development!Meditel PHP Class: Une classe PHP qui vous permet de d'envoyer des SMS vers tous les numeros Meditel en utilisant leservice des SMS gratuits depuis le site Meditel.maMoneySafe: Help people.Mouse Zoom - Visual Studio Extension: Mouse Zoom is a Visual Studio 2010 extension that will cause the mouse zoom functionality to zoom at the mouse's cursor instead of at the top of th...Multi-Language Words Memorizer: This .net application is designed for learning words and help foreign language learners by lots of automatic features. After you select a list of ...Navigation for ASP.NET Web Forms: Navigation for ASP.NET Web Forms manages movement and data passing between aspx Pages in a unit testable manner. There is no Client-side logic, so ...NazTek.Extension.Clr4: CLR 4.0 extensions and utility APIOpalis Community Releases: Sample workflows, objects, code and other items related to System Center's Opalis Integration Server, published by the Opalis team.Power Video Player: Power Video Player is a slim feature-rich video/dvd player that meets everyday needs in video playback on PC with a bunch of advanced features on b...SchemeEditor: <WPF> <.NET> <Editor> <Silverlight> <Scheme> <Graphics> <simulink> <schematic>StyleCop+: StyleCop+ is a plug-in that extends original StyleCop features.timemanager2010: Just another work time managerTweetTunes: Updates Twitter with current song playing in iTunes - if your Twitter account is linked to Facebook - it will update that too The twittervb2 down...WCF Discovery Library: WCF Discovery Library is a small collection of utilities that makes it easy to add WCF 4.0 Discovery features into your projects.New ReleasesAjaxControlToolkit additional extenders: ControlToolkitExtended: this build contains web example with BreadCrumbsAnyCAD: AnyCAD Free Beta1: AnyCAD Free Beta1Baccarat: Single player practice baccarat: This is a simple baccarat game for Windows Mobile. It is single player and is only a practice version, which will help users familiarize themselve...BigDoor .NET Client: BigDoor .NET 2.0 Client (Alpha): Our first iteration of the .NET client. Please fork and or ask to be added if you want to make any contributions.CBM-Command: 2010-05-04: Release NotesNew Features Panel navigation now complete. Scroll up and down through directories using the up and down cursor keys. Switch between...Directory Linker: Directory Linker 2.1: This release introduces XP support, more information about all features can be found at http://www.humblecoder.co.uk/?p=141Extend SmallBasic: Teaching Extensions v.015: added high low quizGoogle AJAX Search Services for jQuery: jquery.gss-0.1.3.js: First official release - use at your own discretion. Thanks, AndrewIndustrial Dashboard Connected Grid webpart: Filtered Industrial Grid: Filtered Industrial Grid web part for SharePoint 2007/2010, First Release.jQuery Library for SharePoint Web Services: SPServices 0.5.5: IMPORTANT NOTE: This release is in an alpha state. You should only download it if you know what you are getting and are interested in testing it f...Meditel PHP Class: Meditel PHP Class: Zipped File : Example : exemplemeditel.php PHP Class : meditel.class.phpMulti-Language Words Memorizer: Memorizer 1.0: First release.mwNSPECT: mwNSPECT Plugin DLL: mwNSPECT Mapwindow plugin dll. Place in your MapWindow or BASINS plugins directory. Presently only for testing form functionality (not including...mwNSPECT: mwNSPECT Simple Installer: Simplistic mwNSPECT Mapwindow plugin installer using Inno setup. Installs all the files you'll need for NSPECT into the C:\NSPECT folder and insta...MyWSAT - ASP.NET Membership Administration Tool: MyWSAT v3.5.3: MyWSAT 3.5.3 Update Notes - May 4th 2010 1.) Added the user search box and a-z navigation menu to all relevant user gridviews. 2.) Added a membersh...Object/Relational Mapper & Code Generator in Net 2.0 for Relational & XML Schema: 2.7: Upgraded UI-generation templates for special case of associative tables (2-column primary keys). Minor bugfix with template-editor.Open NFSe: Open NFSe 2.0: Versao para Belo Horizonte utilizando Windows Services.Power Video Player: PVP 1.1.3776: v1.1.3776 This is mainly a rebuild of version 1.1 under Ms-PL license and is the 1st version available at CodePlex.PROGRAMMABLE SOFTWARE DEVELOPMENT ENVIRONMENT: PROGRAMMABLE SOFTWARE DEVELOPMENT ENVIRONMENT-3.1: The following error has been corrected: PCG ERROR: srcproj -- 3933 PCG ERROR: srcproj -- 2943 PCG ERROR: devproj -- 1474 PCG ERROR: mainprj -- 128...Rehost Image: 1.3.9: Fixed locations saving for mac and linux platforms.Robot Shootans: Robot Shootans 0.5.1 (Windows): This is the first public release of this game. Instructions on how to play are included in the game itself Known issues: Changing control style wh...SchemeEditor: SchemeEditor Beta: First release. Wait for documentation & update for some new functionSharePoint Rsync List: SharePoint Rsync 0.9.0.0: Initial release of sprsync. Comments, questions, feedback, and code enhancements are welcome!Software Is Hardwork: Sw. Is Hw. Lib. 3.0.0.x+01: Sw. Is Hw. Lib. 3.0.0.x+01 UNSUPPORTED, UNTESTED ALPHA RELEASE Code may disappear. This is just a preview of code that was in progress. Code is s...Software Localization Tool: SharpSLT 1.0.1: Minor release: bug fixes slight changes in the UIStyleCop+: StyleCop+ 0.6: Several important improvements made for Advanced Naming Rules: - Added new entities for fields and constants - Added new entities for methods (incl...turing machine simulator: First version of turing machine: Overview: First version of turing simulator with example script (transaction function). Files: SimulatorGui.exe - main GUI of simulator TuringMach...VCC: Latest build, v2.1.30504.0: Automatic drop of latest buildVocabulary Training Center: Basic Edition 1.1: A release with medium large changes: New functionality: Multiple-choice questions added Grammatical questions added Evaluation changed accordin...Web Service Software Factory: Web Service Software Factory 2010 RC: To use the Web Service Software Factory 2010, you need the following software installed on your computer: • Microsoft Visual Studio 2010 (Ultima...Web Service Software Factory: WSSF2010 Guide: This is the help and guidance for Web Service Software Factory 2010Windows Phone 7 Panorama control: panorama control v0.6 + samples: IMPORTANT NOTE: Please read the following bug + suggested workaround. I'll fix this in a new release shortly. Panorama Control source code + sampl...WPF Behavior Library: WPF Behavior Library 0.2 Release: Drag & Drop Took away the ItemType and DataTemplate requirements Added functions for inheritors to be able to provide custom logic to handle movi...Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight Toolkitpatterns & practices – Enterprise LibraryWindows Presentation Foundation (WPF)iTuner - The iTunes CompanionDotNetNuke® Community EditionASP.NETMost Active Projectspatterns & practices – Enterprise LibraryAJAX Control FrameworkHydroServer - CUAHSI Hydrologic Information System ServerIonics Isapi Rewrite Filterpatterns & practices: Azure Security GuidanceRawrBlogEngine.NETTinyProjectNB_Store - Free DotNetNuke Ecommerce Catalog ModuleAll-In-One Code Framework

  Read the article

• guvcview recording video and audio out of synchronisation in Ubuntu 10.10

  - by SIJAR

  I finally got Guvcview, a great software for Logitech webcam and it does all the stuff that one wants out of it. But I'm not satisfy with the video recording, video and audio out of synchronisation also video seems to be in slow motion. Please help so that I can tweak in and get a good video recording with the webcam. Below is the log of Guvcview ------------------------------------------------------------------------------- guvcview 1.4.1 video_device: /dev/video0 vid_sleep: 0 cap_meth: 1 resolution: 640 x 480 windowsize: 1024 x 715 vert pane: 578 spin behavior: 0 mode: mjpg fps: 1/25 Display Fps: 0 bpp: 0 hwaccel: 1 avi_format: 4 sound: 1 sound Device: 4 sound samp rate: 0 sound Channels: 0 Sound delay: 0 nanosec Sound Format: 85 Pan Step: 2 degrees Tilt Step: 2 degrees Video Filter Flags: 0 image inc: 0 profile(default):/home/sijar/default.gpfl starting portaudio... bt_audio_service_open: connect() failed: Connection refused (111) bt_audio_service_open: connect() failed: Connection refused (111) bt_audio_service_open: connect() failed: Connection refused (111) bt_audio_service_open: connect() failed: Connection refused (111) Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started language catalog= dir:/usr/share/locale type:UTF-8 lang:en_US.utf8 cat:guvcview.mo mjpg: setting format to 1196444237 capture method = 1 video device: /dev/video0 libv4lconvert: warning more framesizes then I can handle! libv4lconvert: warning more framesizes then I can handle! /dev/video0 - device 1 libv4lconvert: warning more framesizes then I can handle! libv4lconvert: warning more framesizes then I can handle! Init. UVC Camera (046d:0825) (location: usb-0000:00:1d.7-5) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 176 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 432, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 544, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 640, height = 360 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, ... repeats a couple of times ... vid:046d pid:0825 driver:uvcvideo Adding control for Pan (relative) UVCIOC_CTRL_ADD - Error: Operation not permitted checking format: 1196444237 VIDIOC_G_COMP:: Invalid argument compression control not supported fps is set to 1/25 drawing controls control[0]: 0x980900 Brightness, 0:255:1, default 128 control[0]: 0x980901 Contrast, 0:255:1, default 32 control[0]: 0x980902 Saturation, 0:255:1, default 32 control[0]: 0x98090c White Balance Temperature, Auto, 0:1:1, default 1 control[0]: 0x980913 Gain, 0:255:1, default 0 control[0]: 0x980918 Power Line Frequency, 0:2:1, default 2 control[0]: 0x98091a White Balance Temperature, 0:10000:10, default 4000 control[0]: 0x98091b Sharpness, 0:255:1, default 24 control[0]: 0x98091c Backlight Compensation, 0:1:1, default 1 control[0]: 0x9a0901 Exposure, Auto, 0:3:1, default 3 control[0]: 0x9a0902 Exposure (Absolute), 1:10000:1, default 166 control[0]: 0x9a0903 Exposure, Auto Priority, 0:1:1, default 0 resolutions of format(2) = 19 frame rates of 1º resolution=6 Def. Res: 0 numb. fps:6 --------------------------------------- device #0 Name = Intel 82801DB-ICH4: Intel 82801DB-ICH4 (hw:0,0) Host API = ALSA Max inputs = 2, Max outputs = 2 Def. low input latency = 0.012 Def. low output latency = 0.012 Def. high input latency = 0.046 Def. high output latency = 0.046 Def. sample rate = 44100.00 --------------------------------------- device #1 Name = Intel 82801DB-ICH4: Intel 82801DB-ICH4 - MIC ADC (hw:0,1) Host API = ALSA Max inputs = 2, Max outputs = 0 Def. low input latency = 0.011 Def. low output latency = -1.000 Def. high input latency = 0.043 Def. high output latency = -1.000 Def. sample rate = 48000.00 --------------------------------------- device #2 Name = Intel 82801DB-ICH4: Intel 82801DB-ICH4 - MIC2 ADC (hw:0,2) Host API = ALSA Max inputs = 2, Max outputs = 0 Def. low input latency = 0.011 Def. low output latency = -1.000 Def. high input latency = 0.043 Def. high output latency = -1.000 Def. sample rate = 48000.00 --------------------------------------- device #3 Name = Intel 82801DB-ICH4: Intel 82801DB-ICH4 - ADC2 (hw:0,3) Host API = ALSA Max inputs = 2, Max outputs = 0 Def. low input latency = 0.011 Def. low output latency = -1.000 Def. high input latency = 0.043 Def. high output latency = -1.000 Def. sample rate = 48000.00 --------------------------------------- device #4 Name = Intel 82801DB-ICH4: Intel 82801DB-ICH4 - IEC958 (hw:0,4) Host API = ALSA Max inputs = 0, Max outputs = 2 Def. low input latency = -1.000 Def. low output latency = 0.011 Def. high input latency = -1.000 Def. high output latency = 0.043 Def. sample rate = 48000.00 --------------------------------------- device #5 Name = USB Device 0x46d:0x825: USB Audio (hw:1,0) Host API = ALSA Max inputs = 1, Max outputs = 0 Def. low input latency = 0.011 Def. low output latency = -1.000 Def. high input latency = 0.043 Def. high output latency = -1.000 Def. sample rate = 48000.00 --------------------------------------- device #6 Name = front Host API = ALSA Max inputs = 0, Max outputs = 2 Def. low input latency = -1.000 Def. low output latency = 0.012 Def. high input latency = -1.000 Def. high output latency = 0.046 Def. sample rate = 44100.00 --------------------------------------- device #7 Name = iec958 Host API = ALSA Max inputs = 0, Max outputs = 2 Def. low input latency = -1.000 Def. low output latency = 0.011 Def. high input latency = -1.000 Def. high output latency = 0.043 Def. sample rate = 48000.00 --------------------------------------- device #8 Name = spdif Host API = ALSA Max inputs = 0, Max outputs = 2 Def. low input latency = -1.000 Def. low output latency = 0.011 Def. high input latency = -1.000 Def. high output latency = 0.043 Def. sample rate = 48000.00 --------------------------------------- device #9 Name = pulse Host API = ALSA Max inputs = 32, Max outputs = 32 Def. low input latency = 0.012 Def. low output latency = 0.012 Def. high input latency = 0.046 Def. high output latency = 0.046 Def. sample rate = 44100.00 --------------------------------------- device #10 Name = dmix Host API = ALSA Max inputs = 0, Max outputs = 2 Def. low input latency = -1.000 Def. low output latency = 0.043 Def. high input latency = -1.000 Def. high output latency = 0.043 Def. sample rate = 48000.00 --------------------------------------- device #11 [ Default Input, Default Output ] Name = default Host API = ALSA Max inputs = 32, Max outputs = 32 Def. low input latency = 0.012 Def. low output latency = 0.012 Def. high input latency = 0.046 Def. high output latency = 0.046 Def. sample rate = 44100.00 ---------------------------------------------- SampleRate:0 Channels:0 Video driver: x11 A window manager is available VIDIOC_S_EXT_CTRLS for multiple controls failed (error -1) using VIDIOC_S_CTRL for user class controls control(0x0098091a) "White Balance Temperature" failed to set (error -1) VIDIOC_S_EXT_CTRLS for multiple controls failed (error -1) using VIDIOC_S_EXT_CTRLS on single controls for class: 0x009a0000 control(0x009a0902) "Exposure (Absolute)" failed to set (error -1) VIDIOC_S_EXT_CTRLS for multiple controls failed (error -1) using VIDIOC_S_CTRL for user class controls control(0x0098091a) "White Balance Temperature" failed to set (error -1) VIDIOC_S_EXT_CTRLS for multiple controls failed (error -1) using VIDIOC_S_EXT_CTRLS on single controls for class: 0x009a0000 control(0x009a0902) "Exposure (Absolute)" failed to set (error -1) Cap Video toggled: 1 (/home/sijar/Videos/Webcam) 25371756K bytes free on a total of 39908968K (used: 36 %) treshold=51200K using audio codec: 0x0055 Audio frame size is 1152 samples for selected codec IO thread started...OK [libx264 @ 0x8cbd8b0]using cpu capabilities: MMX2 SSE2 Cache64 [libx264 @ 0x8cbd8b0]profile Baseline, level 3.0 [libx264 @ 0x8cbd8b0]non-strictly-monotonic PTS shift sound by -9 ms shift sound by -9 ms shift sound by -9 ms AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data ... repeats a couple of times ... AUDIO: droping audio data (/home/sijar/Videos/Webcam) 25371748K bytes free on a total of 39908968K (used: 36 %) treshold=51200K AUDIO: droping audio data AUDIO: droping audio data ... repeats a couple of times ... Cap Video toggled: 0 Shuting Down IO Thread AUDIO: droping audio data stop= 4426644744000 start=4416533023000 VIDEO: 146 frames in 10111.000000 ms = 14.439719 fps Stoping audio stream Closing audio stream... close avi Last message repeated 145 times [libx264 @ 0x8cbd8b0]frame I:2 Avg QP:14.10 size: 24492 [libx264 @ 0x8cbd8b0]frame P:103 Avg QP:16.06 size: 20715 [libx264 @ 0x8cbd8b0]mb I I16..4: 48.4% 0.0% 51.6% [libx264 @ 0x8cbd8b0]mb P I16..4: 57.5% 0.0% 0.0% P16..4: 40.2% 0.0% 0.0% 0.0% 0.0% skip: 2.3% [libx264 @ 0x8cbd8b0]final ratefactor: 62.05 [libx264 @ 0x8cbd8b0]coded y,uvDC,uvAC intra: 79.7% 92.2% 68.4% inter: 62.4% 87.5% 48.0% [libx264 @ 0x8cbd8b0]i16 v,h,dc,p: 23% 17% 41% 19% [libx264 @ 0x8cbd8b0]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 30% 24% 26% 2% 5% 3% 3% 3% 4% [libx264 @ 0x8cbd8b0]i8c dc,h,v,p: 53% 20% 23% 4% [libx264 @ 0x8cbd8b0]ref P L0: 63.0% 37.0% [libx264 @ 0x8cbd8b0]kb/s:-0.00 total frames encoded: 0 total audio frames encoded: 0 IO thread finished...OK IO Thread finished enabling controls Cap Video toggled: 1 (/home/sijar/Videos/Webcam) 25379744K bytes free on a total of 39908968K (used: 36 %) treshold=51200K using audio codec: 0x0055 Audio frame size is 1152 samples for selected codec IO thread started...OK [libx264 @ 0x8cfba20]using cpu capabilities: MMX2 SSE2 Cache64 [libx264 @ 0x8cfba20]profile Baseline, level 3.0 [libx264 @ 0x8cfba20]non-strictly-monotonic PTS shift sound by -236 ms shift sound by -236 ms shift sound by -236 ms (/home/sijar/Videos/Webcam) 25377044K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25373408K bytes free on a total of 39908968K (used: 36 %) treshold=51200K AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data ... repeats a couple of times ... (/home/sijar/Videos/Webcam) 25370696K bytes free on a total of 39908968K (used: 36 %) treshold=51200K AUDIO: droping audio data AUDIO: droping audio data AUDIO: droping audio data ... repeats a couple of times ... (/home/sijar/Videos/Webcam) 25367680K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25364052K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25360312K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25356628K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25352908K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25349316K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25345552K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25341828K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25338092K bytes free on a total of 39908968K (used: 36 %) treshold=51200K (/home/sijar/Videos/Webcam) 25334412K bytes free on a total of 39908968K (used: 36 %) treshold=51200K Cap Video toggled: 0 Shuting Down IO Thread stop= 4708817235000 start=4578624714000 VIDEO: 1604 frames in 130192.000000 ms = 12.320265 fps Stoping audio stream Closing audio stream... close avi Last message repeated 1603 times [libx264 @ 0x8cfba20]frame I:16 Avg QP:14.78 size: 42627 [libx264 @ 0x8cfba20]frame P:1547 Avg QP:16.44 size: 28599 [libx264 @ 0x8cfba20]mb I I16..4: 21.6% 0.0% 78.4% [libx264 @ 0x8cfba20]mb P I16..4: 28.1% 0.0% 0.0% P16..4: 70.5% 0.0% 0.0% 0.0% 0.0% skip: 1.4% [libx264 @ 0x8cfba20]final ratefactor: 88.17 [libx264 @ 0x8cfba20]coded y,uvDC,uvAC intra: 74.4% 95.8% 83.2% inter: 75.2% 94.6% 69.2% [libx264 @ 0x8cfba20]i16 v,h,dc,p: 27% 17% 40% 16% [libx264 @ 0x8cfba20]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 25% 25% 21% 3% 6% 4% 5% 4% 7% [libx264 @ 0x8cfba20]i8c dc,h,v,p: 61% 18% 18% 4% [libx264 @ 0x8cfba20]ref P L0: 64.0% 36.0% [libx264 @ 0x8cfba20]kb/s:-0.00 total frames encoded: 0 total audio frames encoded: 0 IO thread finished...OK IO Thread finished enabling controls Shuting Down Thread Thread terminated... cleaning Thread allocations: 100% SDL Quit Video Thread finished write /home/sijar/.guvcviewrc OK free audio mutex closed v4l2 strutures free controls free controls - vidState cleaned allocations - 100% Closing portaudio ...OK Closing GTK... OK

  Read the article

• Windows Azure Evolution &ndash; Preview Developer Portal

  - by Shaun

  With the MEET Windows Azure event on 7th June, there are many new features and updates in windows azure platform. In the coming several posts I will try to cover some of them. And in the first post here I would like to just have a quick walkthrough of the new preview developer portal.   History of the Developer Portal If you have been working with windows azure since 2009 or 2010, you should remember the first version of the developer portal. It was built in HTML with very limited features. I have the impression when I was using is old one. The layout is not that attractive and you have very limited features. On November, 2010 alone with the SDK 1.3 release, the developer portal was getting a big jump. In order to give more usability and features this it turned to be built on Silverlight. Hence it runs like a desktop application with many windows, lists, commands and context menus. From 2010 till now many features were involved into this portal, such as the remote desktop, co-admin, virtual connect, VM role, etc.. And the portal itself became more and more complicated. But it brought some problems by using the Silverlight. The first one is the browser capability. As you know in most mobile and tablet device the browser doesn’t allow the rich content plugin, such as Flash and Silverlight. This means people cannot open and configure their azure services from their iPad, iPhone and Windows Phone, etc., even though what they need may just be restart a hosted service, or view the status of their databases. Another problem is the performance. Silverlight provides rich experience to the users, but also needs more bandwidth. So in this upgrade the preview developer portal will be back to use HTML, with JavaScript, as a mobile friendly, cross browser, interactively web site.   Preview Portal vs. Silverlight Portal Before I started to talk about the new preview portal I’d better highlight that, this preview portal is a PREVIEW version, which means even though you can do almost all features that already in the old one, as long as some cool new features I will mention in the coming several posts, there are something still under developed and migrated. So sometimes you need to switch back to the old one. For example, in preview portal there is no co-admin manage function, no remote desktop function and the SQL database manage function will take you back to the old SQL Azure Manage Portal. But as Microsoft said these missing features will be moved in the preview portal in the couple of next few months. Since the public URL of the developer portal, https://windows.azure.com/, had been changed to point to this preview one, you need to click to preview button on top of the page and click the “Take me to the previous portal” link.   Overview There are four parts in the preview portal. On the top is the header which shows the account you are currently logging in. If you click on the header it will show the top menu of windows azure, where you can navigate to the windows azure home page, the price information page, community and account, etc.. The navigation bar is on the left hand side, with the categories listed below. ALL ITEMS All items in your windows azure account, includes the web sites, services, databases, etc.. WEB SITES The web sites in your windows azure account. It will only show the web sites you have. The linked resources will be shown if you drill down into a web site. VIRTUAL MACHINES The virtual machines that you had been deployed to azure. CLOUD SERVICES All windows azure hosted services in your account. SQL DATABASES All SQL databases (SQL Azure) in your account. STORAGE All windows azure storage services in your account. NETWORKS The virtual network (Windows Azure Connect) you had been created. The available items will be listed in the main part of the page based on which category your currently selected. If there’s no item it will show the link to you to quick create. At the bottom of the page there will be the command and information bar. Based on what is selected and what is performed by the user, it will show the related information and commands. For example, in the image below when I was creating a new web site, the information bar told me that my web site is being provisioned; and there are two commands in the command bar. And once it ready the command bar will show some commands that I can do to my new web site. The “Web Sites” is a new feature introduced alone with this upgrade. It gives us an easier and quicker way to establish a website from the scratch or from some existing library. I will introduce it more details in the coming next post. Also in the command bar you can create a service by clicking the NEW button. It will slide the creation panel up to you.   Where’s My Hosted Services The Windows Azure Hosted Services had been renamed to the Cloud Services. Create a new service would be very easy. Just click the NEW button at the bottom of the page, and select the CLOUD SERVICE and QIUICK CREATE. This will create a blank hosted service without deployment and certificate. It just needs you to specify the service URL and the affinity/region. Then the service will be shown in the list. If you clicked the item all information will be shown in the main part. Since there’s no package deployed to this service so currently we cannot see any information about it. But we can upload the package by using the command at the bottom. And as you can see, we could manage the configuration, instances, certificates and we can scale up and down (change the VM size), in and out (increase and decrease the instance count) to our service. Assuming I had created an ASP.NET MVC 3 web role project in Visual Studio and completed the package. Then I can click the UPLOAD button in this page to deploy my package. In the popping up window I just specify my deployment name, package file and configure file. Also I can check the box below so that it will NOT warn me if only one instance of this deployment. Once we clicked the OK button our package will be uploaded and provisioned by the platform. After a while we can see the service was ready from the information bar. We can have the basic information about this service and deployment if we to the dashboard page. For example the usage overview diagram, status, URL, public IP address, etc.. In the configure page we can view and change the CSCFG content such as the monitor setting, connection strings, OS family. In scale page we can increase and decrease the count of the instances. And in the instances page we can view all instances status. And, if your services is using some SQL databases and storages they will be shown as the linked resources under the linked resources page. And you can manage the certificates of this service as well under the certificates page.   How About My Storage Services The storage service can be managed by clicking into the STORAGES link in the navigation bar. And we can create a new storage service from the NEW button. After specify the storage name and region it will be previsioned by the platform. If you want to copy or manage the storage key you can just click the Manage Keys button at the bottom, which is very easy. What I want to highlight here is that, you can monitor your storage service by enabling the monitor configuration. Click the storage item in the list and navigate to the configure page. As you can see in the page you can enable the monitoring for blob, table and queue. And you can also enable the logging when any requests come to the storage. But as the tooltip shown in the page, enabling the monitoring and logging will increase the usage of the storage, which means increase the bill of them. So make sure you enable them properly.   And My SQL Databases (SQL Azure) The last thing I want to quick introduce is the SQL databases, which was formally named SQL Azure. You can create a new SQL Database Server and a new database by clicking the ADD button under the SQL Database navigation item. In the popping up windows just specify the database name, the edition, size, collation and the server. You can select an existing SQL Database Server if you have, or cerate a new one. If you selected to create a new server, there will be another step you need to do, which is specify the server login, password and the region. Once it ready you can mange your databases as well as the servers in the portal. In a particular server you can update the firewall settings in its Configure page. So, What Else There are some other area on the preview portal I didn’t cover, such as the virtual machines, virtual network and web sites. Regarding the virtual machines and web sites I will talk about them in the future separated post. Regarding the virtual network, it the Windows Azure Connect we are familiar with. But as I mention in the beginning of this post, the preview portal is still under developed. Some features are not available here. For example, you cannot manage the co-admin of your subscriptions, you cannot open the remote desktop on your hosted services, and you cannot navigate to the Windows Azure Service Bus, Access Control and Caching, which formally named Windows Azure AppFabric directly. In these cases you need to navigate back to the old portal. So in the coming several months we might need to use both these two sites.   Summary In this post I quick introduced the new windows azure developer portal. Since it had been rearranged and renamed I demonstrated some features that existing in the old portal, such as how to create and deploy a hosted service, how to provision a storage service and SQL database. All features in the old portal had been, is being and will be migrated into this new portal, but some of them were in a different category and page we need to figure out.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

  Read the article

< Previous Page | 800 801 802 803 804 805 806 807 808 809 810 811  | Next Page >