Search Results

Search found 22065 results on 883 pages for 'performance testing'.

Page 809/883 | < Previous Page | 805 806 807 808 809 810 811 812 813 814 815 816  | Next Page >

  • Are file access times not properly maintained in Mac OS X?

    - by Ether
    I'm trying to determine how file access times are maintained by default in Mac OS X, as I'm trying to diagnose some odd behaviour I'm seeing in a new MBP Unibody (running Snow Leopard, 10.6.2): The symptoms (drilling down to the specific behaviour that seems to be causing the issue): mutt is unable to switch to mailboxes which have recently received new mail mail is delivered by procmail, which updates the mtime of the mbox folder it is updating, but does not alter the atime (this is how new mail detection works: by comparing atime to mtime) however, both the mtime and atime of the mbox file is getting updated Through testing, it does not appear that atimes can be set separately in the filesystem: : [ether@tequila ~]$; touch test : [ether@tequila ~]$; touch -m -t 200801010000 test2 : [ether@tequila ~]$; touch -a -t 200801010000 test3 : [ether@tequila ~]$; ls -l test* -rw------- 1 ether staff 0 Dec 30 11:42 test -rw------- 1 ether staff 0 Jan 1 2008 test2 -rw------- 1 ether staff 0 Dec 30 11:43 test3 : [ether@tequila ~]$; ls -lu test* -rw------- 1 ether staff 0 Dec 30 11:42 test -rw------- 1 ether staff 0 Dec 30 11:43 test2 -rw------- 1 ether staff 0 Dec 30 11:43 test3 The test2 file is created with an old mtime, and the atime is set to now (as it is a new file), which is correct. However, test3 is created with an old atime, but is not set properly on the file. To be sure this is not just behaviour seen with new files, let's modify an old file: : [ether@tequila ~]$; touch -a -t 200801010000 test : [ether@tequila ~]$; ls -l test -rw------- 1 ether staff 0 Dec 30 11:42 test : [ether@tequila ~]$; ls -lu test -rw------- 1 ether staff 0 Dec 30 11:45 test So it would seem that atimes cannot be set explicitly (it is always reset to "now" when either mtime or atime modifications are submitted). Is this something inherent to the filesystem itself, is it something that can be changed, or am I totally crazy and looking in the wrong place? PS. the output of mount is: : [ether@tequila ~]$; mount /dev/disk0s2 on / (hfs, local, journaled) devfs on /dev (devfs, local, nobrowse) map -hosts on /net (autofs, nosuid, automounted, nobrowse) map auto_home on /home (autofs, automounted, nobrowse) ...and Disk Utility says that the drive is of type "Mac OS Extended (Journaled)".

    Read the article

  • Blank displays after inactivity, mouse cursor not showing up

    - by Mike Christiansen
    I have a Windows 7 Enterprise x86 machine that is exhibiting some strange problems. After some inactivity (it varies how long it takes), when I come back to my computer, both of my monitors are black. The monitors are on, with a black display. Moving the mouse and pressing keys on the keyboard do not work. This happens at least once a day. When I first encountered the issue, I performed a hard shutdown and restarted the computer. About 10% of the time when I did this, the resolutions on my monitors were messed up. The native resolution on the primary monitor is 1600x900, and the native on my secondary is 1440x900. None of the widescreen resolutions would be present in the display properties. I had 800x600, 1024x768, and 1280x1024. As a workaround to this issue, I've found that if I plug in my secondary monitor as the primary monitor, and leave the secondary unplugged, then Windows will start in 1024x768 on the secondary. Then, I can use Windows 7's "Detect" feature and it finds the 1440x900 resolution, and sets it. Then I have to connect the primary monitor to the secondary port and set it as the primary. Then I can switch the two cables, putting the primary into the primary, the secondary into the secondary. Then use the "Detect" feature again, and it finds the correct resolutions. Some time after performing the above, I discovered that when the screens were blanked, I could simply press "Control+Alt+Delete", type in my password, and everything comes up fine - except my mouse cursor. All applications and features work as intended, except there is no mouse cursor (the mouse actually works though...). I have the "Show location of pointer when I press CTRL key" option selected, so I can press CTRL and use my mouse as normal - but I have no actual cursor. When the computer is in this state, UAC is also not functional. Whenever a UAC prompt appears, the screens go black (the original symptoms) and I have to press Escape to exit UAC. Because of the above symptoms (the UAC black screen thing, etc) I beleive winlogon.exe may be the culprit. However, I have no idea how to fix it. I am unable to restart winlogon.exe due to the problems I am having with winlogon.exe (the UAC black screen) Looking for any ideas.... More information Windows 7 x86 Enterprise Domain environment (I have a secondary account with administrator rights) Dell Optiplex 960 Cannot perform "optional" windows updates due to an activation issue (I am testing a windows 7 image, and an activation infrastructure has not been created yet. However, this issue was happening before I was unable to perform windows update, and windows was up to date at the time Updated video card driver (as an attempt to fixing the resolution issue) Disabled all power saving options Please let me know what else you need to help me solve this issue! Thanks in advance, Mike

    Read the article

  • What are the pros and cons of AWS Elastic Beanstalk compared with other deployment strategies?

    - by James van Dyke
    I'm pretty new to the whole Netflix OSS stack and deployments in general. As a background for my current level of knowledge ops-wise, my main role is as a front-end application engineer. However, I enjoy the operations side of things, so I'm attempting to setup a new deployment strategy and the tooling for a new project. Our Goals Super easy deploys (we want to push a button to update production) Automated deploys to test environments (using Jenkins) Ease of maintenance (we have an app to write, don't want to spend our time fiddling with production issues) Ability to handle a service oriented architecture (many small apps, various languages and data stores) Enough flexibility to ensure we won't have to change strategies any time soon (we're already trying to get away from RightScale) We're OK with a little more initial setup time if doing so will save us some headaches in the future. So, along these lines, I've been listening to podcasts, watching Ops talks, and reading tons of blog posts and based on our goals and what I've taken to be some forming best practices, we've started forming a plan using Asgard, rolling our package into a jar and rolling that into an AMI. We had this all planned out and like the advantages the process versus using a Chef server and converging instances on the fly (we felt this was error prone given our limited timeline and lack of understanding around a Chef server workflow). However, a coworker did a little looking around on his own and felt like Elastic Beanstalk met our needs. I've looked into it and spun up a test environment with a WAR file and an attached RDS database. Things seem to work and I believe that we can automate deploys to a testing environment using Jenkins via the AWS API. Seems simple enough... perhaps too simple. What I'm wondering is, what's the catch? If Elastic Beanstalk is so simple and effective, why isn't it talked about more? I'm having a hard time finding enough objective opinions and facts about the two different deployment strategies, so I thought I'd ask around. Do you use Elastic Beanstalk? If so, why and what factors lead to that decision? What do you like and dislike? If you don't use Elastic Beanstalk but considered it, what do you use and why didn't you use Elastic Beanstalk? What are the advantages and disadvantages to a Elastic Beanstalk based deployment strategy for an SOA? That is, will Elastic Beanstalk work well with many small applications that rely on each other to work?

    Read the article

  • Flickering issue in external monitor when used with Acer Aspire One D260 netbook (Intel GMA 3150)

    - by seyenne
    I recently purchased a Acer netbook, Aspire One D260. It runs flawlessly. Yesterday I bought a Samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the Intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cable to connect, the monitor instantly switches to the native resolution and now the problem: Occasionally, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time.. Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur... but for sure, soon or later it will happen again.. I forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

    Read the article

  • iCloud stuff stops working while connected to OpenVPN [closed]

    - by Taco Bob
    I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again!

    Read the article

  • Active Directory Partition Error

    - by BLAKE
    Right now my active directory is failing a dcdiag test. I can find no info online about this error. When I run dcdiag /test:crossrefvalidation, I get the output: .... Doing primary tests Testing server: Default-First-Site-Name\ad01 Running partition tests on : ForestDnsZones Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Running partition tests on : DomainDnsZones Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Running partition tests on : mydomain Starting test: CrossRefValidation ......................... mydomain passed test CrossRefValidation Running partition tests on : t Starting test: CrossRefValidation This cross-ref has a non-standard dNSRoot attribute. Cross-ref DN: CN=a3a24d3a-4782-460b-9148-86ac2d86b9ae,CN=Partitions,CN=Configuration, DC=mydomain,DC=com nCName attribute (Partition name): DC=t Bad dNSRoot attribute: dc01.mydomain.com Check with your network administrator to make sure this dNSRoot attribute is correct, and if not please change the attribute to the value below. dNSRoot should be: t It appears this partition (DC=t) failed to get completely created. This cross-ref (CN=a3a24d3a-4782-460b-9148-86ac2d86b9ae,CN=Partitions,CN=Configurat ion,DC=mydomain,DC=com) is dead and should be removed from the Active Directory. ......................... t failed test CrossRefValidation .... I used LDP from the windows support tools. I searched for the dnsRoot attribute in "cn=partitions,cn=configuration,dc=mydomain,dc=com", with the filter "(&(objectcategory=crossref)(systemFlags:1.2.840.113556.1.4.803:=5))" I got the result: ***Searching... ldap_search_s(ld, "cn=partitions,CN=Configuration,DC=mydomain,DC=com", 1, "(& (objectcategory=crossref)(systemFlags:1.2.840.113556.1.4.803:=5))", attrList, 0, &msg) Result <0>: (null) Matched DNs: Getting 3 entries: >> Dn: CN=65502be3-fc90-442a-83d8-4b3b91e82439,CN=Partitions,CN=Configuration,DC=mydomain,DC=com 1> dnsRoot: ForestDnsZones.mydomain.com; >> Dn: CN=a3a24d3a-4782-460b-9148-86ac2d86b9ae,CN=Partitions,CN=Configuration,DC=mydomain,DC=com 1> dnsRoot: ad01.mydomain.com; >> Dn: CN=f0ef5771-6225-4984-acd9-c08f582eb4e2,CN=Partitions,CN=Configuration,DC=mydomain,DC=com 1> dnsRoot: DomainDnsZones.mydomain.com; It looks like the bad partition has the name of my first domain controller 'ad01.mydomain.com'. I have googled for a while and have not been able to find any help or documentation about application partitions in Active Directory. Does anyone have any advice on how to cleanup this partition (or what the partition is for)? Does anyone know the repercussions for deleting this partition?

    Read the article

  • Complete Active Directory redesign and GPO application

    - by Wolfgang Kuehne
    after much testing and hundreds of tries and hours invested I decided to consult you experts here. Overview: I want to apply some GPO to our users which will add some specific site to the Trusted Sites in Internet Explorer settings for all users. However, the more I try the more confusing the results become. The GPO is either applied to one group of users, or to another one. Finally, I came to the conclusion that this weird behavior is cause rather by the poor organization in Users and Groups in Active Directory. As such I want to kick the problem from the root: Redesign the Active Directory Users and Groups. Scenario: There is one Domain Controller, and we use Terminal Services (so there is a Terminal Server as well). Users usually log on to the Terminal Server using Remote Desktop to perform their daily tasks. I would classify the users in the following way: IT: Admins, Software Development Business: Administration, Management The current structure of the Active Directory Users and Groups is a result of the previous IT management. The company has used Small Business Server which has created multiple default user groups and containers. Unfortunately, the guys working before me have do no documentation at all. Now, as I inherit this structure I am in the no mans land. No idea which direction to head first. As you can see, the Active Directory User and Groups have become a bit confusing. There is no SBS anymore, but when migrating from SBS to the current Windows Server 2008 R2 environment the guys before me have simply copied the same structure. The real question: Where should I start cleaning from, ensuring that I won't break totally the current infrastructure? What is a nice organization for the scenario that I have explained above? Possible useful info for the current structure: Computers folder contains Terminal Services Computers user group Members: TerminalServer computer located at Server -> Terminalserver OU Member of: NONE Foreign Security Principals : EMPTY Managed Service Accounts : EMPTY Microsoft Exchange Security Groups : not sure if needed, our emails are administered by external service provider Distribution Groups : not sure if needed Security Groups : there are couple of groups which are needed SBS users : contains all the users Terminalserver : contains only the TerminalServer machine

    Read the article

  • How to make Shared Keys .ssh/authorized_keys and sudo work together?

    - by farinspace
    I've setup the .ssh/authorized_keys and am able to login with the new "user" using the pub/private key ... I have also added "user" to the sudoers list ... the problem I have now is when I try to execute a sudo command, something simple like: $ sudo cd /root it will prompt me for my password, which I enter, but it doesn't work (I am using the private key password I set) Also, ive disabled the users password using $ passwd -l user What am I missing? Somewhere my initial remarks are being misunderstood ... I am trying to harden my system ... the ultimate goal is to use pub/private keys to do logins versus simple password authentication. I've figured out how to set all that up via the authorized_keys file. Additionally I will ultimately prevent server logins through the root account. But before I do that I need sudo to work for a second user (the user which I will be login into the system with all the time). For this second user I want to prevent regular password logins and force only pub/private key logins, if I don't lock the user via" passwd -l user ... then if i dont use a key, i can still get into the server with a regular password. But more importantly I need to get sudo to work with a pub/private key setup with a user whos had his/her password disabled. Edit: Ok I think I've got it (the solution): 1) I've adjusted /etc/ssh/sshd_config and set PasswordAuthentication no This will prevent ssh password logins (be sure to have a working public/private key setup prior to doing this 2) I've adjusted the sudoers list visudo and added root ALL=(ALL) ALL dimas ALL=(ALL) NOPASSWD: ALL 3) root is the only user account that will have a password, I am testing with two user accounts "dimas" and "sherry" which do not have a password set (passwords are blank, passwd -d user) The above essentially prevents everyone from logging into the system with passwords (a public/private key must be setup). Additionally users in the sudoers list have admin abilities. They can also su to different accounts. So basically "dimas" can sudo su sherry, however "dimas can NOT do su sherry. Similarly any user NOT in the sudoers list can NOT do su user or sudo su user. NOTE The above works but is considered poor security. Any script that is able to access code as the "dimas" or "sherry" users will be able to execute sudo to gain root access. A bug in ssh that allows remote users to log in despite the settings, a remote code execution in something like firefox, or any other flaw that allows unwanted code to run as the user will now be able to run as root. Sudo should always require a password or you may as well log in as root instead of some other user.

    Read the article

  • Tomcat with virtual hosts - 404

    - by Thardas
    I have a CentOS 5.2 server set up with Apache 2.2.3 and Tomcat 5.5.27. The server hosts multiple virtual hosts connected to multiple Tomcats. For instance we have one tomcat for development and testing and one tomcat for production. project.demo.us.com points to dev tomcat and project.us.com points to production tomcat. Here's the virtual host's configuration: <VirtualHost *:80> ServerName project.demo.us.com CustomLog logs/project.demo.us.com/access_log combined env=!VLOG ErrorLog logs/project.demo.us.com/error_log DocumentRoot /var/www/vhosts/project.demo.us.com <Directory /var/www/vhosts/project.demo.us.com> Allow from all AllowOverride All Options -Indexes FollowSymLinks </Directory> ########## ########## ########## JkMount /project/* online </VirtualHost> JkMount line defines that we use online worker and our workers.properties contains this: worker.list=..., online, ... worker.online.port=7703 worker.online.host=localhost worker.online.type=ajp13 worker.online.lbfactor=1 And tomcat's conf/server.xml contains: <Connector port="7703" enableLookups="false" redirectPort="8443" protocol="AJP/1.3" URIEncoding="UTF-8" maxThreads="80" minSpareThreads="10" maxSpareThreads="15"/> I'm not sure what redirectPort is but I tried to telnet to that port and there's no one answering, so it shouldn't matter? Tomcat's webapps directory contains project.war and the server automatically deployed it under project directory which contains index.jsp and hello.html. The latter is for static debugging purposes. Now when I try to access http://project.demo.us.com/project/index.jsp, I get Tomcat's HTTP Status 404 - The requested resource () is not available. The same thing happens to hello.html so it's not working with static content either. Apache's access_log contains: 88.112.152.31 - - [10/Aug/2009:12:15:14 +0300] "GET /demo/index.jsp HTTP/1.1" 404 952 "-" "Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.5; en-US; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2" I couldn't find any mention of the request in Tomcat's logs. If I shutdown this specific tomcat, I no longer get Tomcat's 404 but Apache's 503 Service Temporarily Unavailable, so I should be configuring the correct Tomcat. Is there something obvious that I'm missing? Is there any place where I could find out what path the Tomcat is using to look for requested files?

    Read the article

  • Is it possible to configure a CDN so that it will step out of the way for a subset of regional IPs?

    - by rwired
    We have a website which targets customers in China, both expat and local Chinese. We have an ICP license which allows us to host in a datacenter inside China. Internet in China is actually as fast as anywhere else (faster than most places actually), so long as the content is served-up within the boundaries of the Great-Firewall. Anything that crosses the wall is horribly slow. The problem is that most expats have some sort of VPN installed so that they can access all the blocked stuff. What this means is that when they access our site, the traffic first has to go out of China through the firewall to their VPN, and then back in. The performance is terrible, worse than if we were just hosting outside of China directly (which we used to do before the ICP was issued). So I want to use a global CDN to mirror the site automatically, but I only want to deliver the content via the CDN if the user's request IP address is outside of China. Inside China I would like the content to be served by our own server. I also want to be careful with the domain names. We currently use www.xxx.com and www.xxx.cn for language selection purposes, as these perform well in SEO on Google (which the expats use), and Baidu (which the locals use). If possible I would like to avoid having one domain on the outside, and the other on the inside since not all expats use a VPN, and some Chinese speakers also use VPNs. Also some of our legitimate customers in both languages are from outside of China. I also don't want to resort to using something like www2.xxx.com/cn for the outside connection if at all possible, since I have worries about duplicate content and canonical URLs ruining our SEO (unless you know of a quick fix for that). CDNs I'm considering are: Google PageSpeed, CloudFlare, Amazon CloudFront. None of which have datacenters inside China. I have complete control of the .com DNS zone records, but the .cn zones are under the control of the domain issuing body in China. I'm not sure at this time if they would allow even a CNAME to point to an IP outside of China (although I don't see why not). They no longer allow outside registrars like they used to.

    Read the article

  • How do I combine static and dynamic DHCP leases on a Cisco router?

    - by Brad
    Basically, what I need is super similar to the unanswered cisco forum question below: https://supportforums.cisco.com/message/3139749#3139749 I have a Cisco 850 Series router. I have configured a DHCP pool for the 10.0.0.0/24 network. I have excluded 10.0.0.1 - 10.0.0.99 from the DHCP pool. I want to add a static DHCP pool for stuff and I want DHCP to statically assign them the addresses of my choice below 100. Actually, I don't care what addresses I statically assign. They can be anything in the pool for all I care, I just want it to work. Why are you doing this? Just statically assign the IPs on the devices! I don't want to do this because I have some laptop users. They could obviously only use that static IP here. This isn't a problem if they could be bothered to change any location setting or something. They can't. So it HAS to be DHCP. It also has to be static IPs because I need to forward ports to them. I know, I know, this is weird but it's an apartment LAN/WLAN so this isn't exactly a typical use case. Relevant sections of config below: ip dhcp excluded-address 10.0.0.1 10.0.0.99 ! ip dhcp pool Internal-net import all network 10.0.0.0 255.255.255.0 default-router 10.0.0.1 domain-name 1770.local lease 7 ! ip dhcp pool static-pool import all origin file flash://staticmap default-router 10.0.0.1 domain-name 1770.local Contents of staticmap: *time* Aug 5 2010 09:00 AM *version* 2 !IP address Type Hardware address Lease expiration 10.0.0.100/24 1 001f.5b3e.d50a Infinite *end* You can see here I was trying addresses outside the excluded-address range to see if that would make any difference. My testing machine's MAC: mainframe:~ brad$ ifconfig en1 en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:1f:5b:3e:d5:0a What shows up in the DHCP binding table: basestar#show ip dhcp binding Bindings from all pools not associated with VRF: IP address Client-ID/ Lease expiration Type Hardware address/ User name 10.0.0.112 0100.1f5b.3ed5.0a Aug 12 2010 10:06 AM Automatic What's up with the funny looking MAC in the DHCP binding table?? Is what I'm trying to accomplish basically impossible? Am I going about this the wrong way? All I want to to be able to port forward some ports to specific devices. The way I would do this with a consumer router is to do what I'm trying to do here; assign static DHCP to those devices then configure PAT for ports on those addresses.

    Read the article

  • How can I force a merge of all WAL files in pg_xlog back into my base "data" directory?

    - by Zac B
    Question: Is there a way to tell Postgres (9.2) to "merge all WAL files in pg_xlog back into the non-WAL data files, and then delete all WAL files successfully merged?" I would like to be able to "force" this operation; i.e. checkpoint_segments or archiving settings should be ignored. The filesystem WAL buffer (pg_xlog) directory should be emptied, or nearly emptied. It's fine if some or all of the space consumed by the pg_xlog directory is then consumed by the data directory; our DBA has asked for WAL database backups without any backlogged WALs, but space consumption is not a concern. Having near-zero WAL activity during this operation is a fine constraint. I can ensure that the database server is either shut down or not connectible (zero user-generated transaction load) during this process. Essentially, I'd like Postgres to ignore archiving/checkpoint retention policies temporarily, and flush all WAL activity to the core database files, leaving pg_xlog in the same state as if the database were recently created--with very few WAL files. What I've Tried: I know that the pg_basebackup utility performs something like this (it generates an almost-all-WALs-merged copy of a Postgres instance's data directory), but we aren't ready to use it on all our systems yet, as we are still testing replication settings; I'm hoping for a more short-term solution. I've tried issuing CHECKPOINT commands, but they just recycle one WAL file and replace it with another (that is, if they do anything at all; if I issue them during database idle time, they do nothing). pg_switch_xlog() similarly just forces a switch to the next log segment; it doesn't flush all queued/buffered segments. I've also played with the pg_resetxlog utility. That utility sort of does what I want, but all of its usage docs seem to indicate that it destroys (rather than flushing out of the transaction log and into the main data files) some or all of the WAL data. Is that impression accurate? If not, can I use pg_resetxlog during a zero-WAL-activity period to force a flush of all queued WAL data to non-WAL data? If the answer to that is negative, how can I achieve this goal? Thanks!

    Read the article

  • HAProxy causing delay

    - by user1221444
    I am trying to configure HAProxy to do load balancing for a custom webserver I created. Right now I am noticing an increasing delay with HAProxy as the size of the return message increases. For example, I ran four different tests, here are the results: Response 15kb through HAProxy: Avg. response time: .34 secs Transacation rate: 763 trans/sec Throughput: 11.08 MB/sec Response 2kb through HAProxy: Avg. response time: .08 secs Transaction rate: 1171 trans / sec Throughput: 2.51 MB/sec Response 15kb directly to server: Avg. response time: .11 sec Transaction rate: 1046 trans/sec throughput: 15.20 MB/sec Response 2kb directly to server: Avg. Response time: .05 secs Transaction rate: 1158 trans/sec Throughput: 2.48 MB/sec All transactions are HTTP requests. As you can see, there seems to be a much bigger difference between response times for when the response is bigger, than when it is smaller. I understand there will be a slight delay when using HAProxy. Not sure if it matters, but the test itself was run using siege. And during the test there was only one server behind the HAProxy(the same that was used in the direct to server tests). Here is my haproxy.config file: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice maxconn 10000 user haproxy group haproxy daemon #debug defaults log global mode http option httplog option dontlognull retries 3 option redispatch option httpclose maxconn 10000 contimeout 10000 clitimeout 50000 srvtimeout 50000 balance roundrobin stats enable stats uri /stats listen lb1 10.1.10.26:80 maxconn 10000 server app1 10.1.10.200:8080 maxconn 5000 I couldn't find much in terms of options in this file that would help my problem. I have heard suggestions that I may have to adjust a few of my sysctl settings. I could not find a lot of information on this however, most documentation is for Linux 2.4 and 2.6 on the sysctl stuff, I am running 3.2(Ubuntu server 12.04), which seems to auto tuning, so I have no clue what I should or shouldn't be changing. Most settings changes I tried had no effect or a negative effect on performance. Just a notice, this is a very preliminary test, and my hope is that at deployment time, my HAProxy will be able to balance 10k-20k requests/sec to many servers, so if anyone could provide information to help me reach that goal, it would be much appreciated. Thank you very much for any information you can provide. And if you need anymore information from me please let me know, I will get you anything I can.

    Read the article

  • External USB HD issues with a twist (works on Windows7 but not XP)

    - by Eruditass
    I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

    Read the article

  • OpenLDAP with StartTLS broken on Debian Lenny

    - by mr.zog
    I'm trying to get OpenLDAP on Lenny to work with StartTLS. I have a Fedora 13 machine which I'm using as a client for testing. So far the Fedora client is ignoring the 'host' directive in /etc/ldap.conf when I try to connect using ldapsearch. The client wants to connect to 127.0.0.1:389 even if I specify -H ldaps://server.name on when using ldapsearch. /etc/ldap.conf on the client machine is in mode 444. But even when I try connecting locally from an ssh session, I see errors like this: ldap_sasl_interactive_bind_s: Can't contact LDAP server (-1) Someone hit me with a cluebat, plz. Update: you must use ~/.ldaprc for settings such as 'host'. Also, I just used nmap against the ldap server and it showed 636 and 389 in an open state. Here's what prints to screen when I try to connect with, ldapsearch -ZZ –x '(objectclass=*)'+ -d -1 ldap_create ldap_extended_operation_s ldap_extended_operation ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP 192.168.10.41:636 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 192.168.10.41:636 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_dump: buf=0x9bdbdb8 ptr=0x9bdbdb8 end=0x9bdbdd7 len=31 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ber_scanf fmt ({) ber: ber_dump: buf=0x9bdbdb8 ptr=0x9bdbdbd end=0x9bdbdd7 len=26 0000: 77 18 80 16 31 2e 33 2e 36 2e 31 2e 34 2e 31 2e w...1.3.6.1.4.1. 0010: 31 34 36 36 2e 32 30 30 33 37 1466.20037 ber_flush2: 31 bytes to sd 3 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ldap_write: want=31, written=31 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ldap_result ld 0x9bd3050 msgid 1 wait4msg ld 0x9bd3050 msgid 1 (infinite timeout) wait4msg continue ld 0x9bd3050 msgid 1 all 1 ** ld 0x9bd3050 Connections: * host: 192.168.10.41 port: 636 (default) refcnt: 2 status: Connected last used: Sun Jun 6 12:54:05 2010 ** ld 0x9bd3050 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x9bd3050 request count 1 (abandoned 0) ** ld 0x9bd3050 Response Queue: Empty ld 0x9bd3050 response count 0 ldap_chkResponseList ld 0x9bd3050 msgid 1 all 1 ldap_chkResponseList returns ld 0x9bd3050 NULL ldap_int_select read1msg: ld 0x9bd3050 msgid 1 all 1 ber_get_next ldap_read: want=8, got=0 ber_get_next failed. ldap_err2string ldap_start_tls: Can't contact LDAP server (-1)

    Read the article

  • Postfix: Relay access denied

    - by Joseph Silvashy
    When I telnet to my server thats running postfix and try to send an email: MAIL FROM:<[email protected]> #=> 250 2.1.0 Ok RCPT TO:<[email protected]> #=> 554 5.7.1 <[email protected]>: Relay access denied I couldn't really find the answer on the site or by looking at other users question/answers, I'm not sure where to start. Ideas? Update So basically looking at the docs: http://www.postfix.org/SMTPD_ACCESS_README.html (section: Getting selective with SMTP access restriction lists), I don't seem to have any of those directives in etc/postfix/main.cf like smtpd_client_restrictions = permit_mynetworks, reject or any of the other ones, so I'm quite confused. But really I'm going to have a rails app connect to the server and send the emails, so I'm not sure how to handle it. Here is what my config file looks like: # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = rerecipe-utils alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = $myhostname, localhost.$mydomain, localhost, mail.rerecipe.com, rerecipe.com relayhost = mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all inet_protocols = all mynetworks = 127.0.0.0/8 204.232.207.0/24 10.177.64.0/19 [::1]/128 [fe80::%eth0]/64 [fe80::%eth1]/64 Something to note is that relayhost is blank, this is the default configuration file that was created when I installed Postfix, when testing to connect with openssl I get this: ~% openssl s_client -connect mail.myhostname.com:25 -starttls smtp CONNECTED(00000003) depth=0 /CN=myhostname verify error:num=18:self signed certificate verify return:1 depth=0 /CN=myhostname verify return:1 --- Certificate chain 0 s:/CN=myhostname i:/CN=myhostname --- Server certificate -----BEGIN CERTIFICATE----- MIIBqTCCARICCQDDxVr+420qvjANBgkqhkiG9w0BAQUFADAZMRcwFQYDVQQDEw5y ZXJlY2lwZS11dGlsczAeFw0xMDEwMTMwNjU1MTVaFw0yMDEwMTAwNjU1MTVaMBkx FzAVBgNVBAMTDnJlcmVjaXBlLXV0aWxzMIGfMA0GCSqGSIb3DQEBAQUAA4GNADCB iQKBgQDODh2w4A1k0qiPNPhkrPj8sfkxpKPTk28AuZhgOEBYBLeHacTKNH0jXxPv P3TyhINijvvdDPzyuPJoTTliR2EHR/nL4DLhr5FzhV+PB4PsIFUER7arx+1sMjz6 5l/Ubu1ppMzW9U0IFNbaPm2AiiGBQRCQN8L0bLUjzVzwoSRMOQIDAQABMA0GCSqG SIb3DQEBBQUAA4GBALi2vvk9TGKJubXYJbU0PKmVmsfzFK35yLqr0keiDBhK2Leg 274sWxEH3ds8mUaRftuFlXb7RYAGNlVyTuMTY3CEcnqIsH7F2McCUTpjMzu/o1mZ O/B21CelKetBd1u79Gkrv2vWyN7Csft6uTx5NIGG2+pGi3r0gX2r0Hbu2K94 -----END CERTIFICATE----- subject=/CN=myhostname issuer=/CN=myhostname --- No client certificate CA names sent --- SSL handshake has read 1203 bytes and written 360 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 1024 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: 1AA4B8BFAAA85DA9ED4755194C50311670E57C35B8C51F9C2749936DA11918E4 Session-ID-ctx: Master-Key: 9B432F1DE9F3580DCC6208C76F96631DC5A4BC517BDBADD5F514414DCF34AC526C30687B96C5C4742E9583555A118232 Key-Arg : None Start Time: 1292985376 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) --- 250 DSN Oddly enough when I try to send an email from the machine itself it does work: echo test | mail -s "test subject" [email protected]

    Read the article

  • Solution to route/proxy SNMP Traps (or Netflow, generic UDP, etc) for network monitoring?

    - by Christopher Cashell
    I'm implementing a network monitoring solution for a very large network (approximately 5000 network devices). We'd like to have all devices on our network send SNMP traps to a single box (technically this will probably be an HA pair of boxes) and then have that box pass the SNMP traps on to the real processing boxes. This will allow us to have multiple back-end boxes handling traps, and to distribute load among those back end boxes. One key feature that we need is the ability to forward the traps to a specific box depending on the source address of the trap. Any suggestions for the best way to handle this? Among the things we've considered are: Using snmptrapd to accept the traps, and have it pass them off to a custom written perl handler script to rewrite the trap and send it to the proper processing box Using some sort of load balancing software running on a Linux box to handle this (having some difficulty finding many load balancing programs that will handle UDP) Using a Load Balancing Appliance (F5, etc) Using IPTables on a Linux box to route the SNMP traps with NATing We've currently implemented and are testing the last solution, with a Linux box with IPTables configured to receive the traps, and then depending on the source address of the trap, rewrite it with a destination nat (DNAT) so the packet gets sent to the proper server. For example: # Range: 10.0.0.0/19 Site: abc01 Destination: foo01 iptables -t nat -A PREROUTING -p udp --dport 162 -s 10.0.0.0/19 -j DNAT --to-destination 10.1.2.3 # Range: 10.0.33.0/21 Site: abc01 Destination: foo01 iptables -t nat -A PREROUTING -p udp --dport 162 -s 10.0.33.0/21 -j DNAT --to-destination 10.1.2.3 # Range: 10.1.0.0/16 Site: xyz01 Destination: bar01 iptables -t nat -A PREROUTING -p udp --dport 162 -s 10.1.0.0/16 -j DNAT --to-destination 10.3.2.1 This should work with excellent efficiency for basic trap routing, but it leaves us completely limited to what we can mach and filter on with IPTables, so we're concerned about flexibility for the future. Another feature that we'd really like, but isn't quite a "must have" is the ability to duplicate or mirror the UDP packets. Being able to take one incoming trap and route it to multiple destinations would be very useful. Has anyone tried any of the possible solutions above for SNMP traps (or Netflow, general UDP, etc) load balancing? Or can anyone think of any other alternatives to solve this?

    Read the article

  • Installing OpenLDAP: ldap_bind: Invalid credentials (49)

    - by Arcturus
    Hello. I've been trying to set up the OpenLDAP installed by default on Fedora 12, very unsuccessfully. My ultimate goal is to use LDAP authentication for user login and Apache, using the OpenLDAP server running on the same machine. The server is running, but the error I always get when I try to use ldapsearch or ldapadd is: ldap_bind: Invalid credentials (49) I've been following these tutorials, but none of them helped me: http://www.howtoforge.com/openldap_fedora7 http://www.redhat.com/docs/manuals/linux/RHL-9-Manual/ref-guide/s1-ldap-quickstart.html http://www.howtoforge.com/linux_ldap_authentication http://docs.fedoraproject.org/deployment-guide/f12/en-US/html/s1-ldap-pam.html http://www.openldap.org/doc/admin24/quickstart.html First, some components were already installed, and I installed these with yum: yum install openldap-servers openldap-devel Then, I created a basic slapd.conf file in /etc/openldap: database bdb suffix "dc=sniejana-sandbox,dc=com" rootdn "cn=root,dc=sniejana-sandbox,dc=com" rootpw {SSHA}cxdz55ygPu4T3ykg7dgu+L0VRvsFSeom directory /var/lib/ldap/sniejana-sandbox.com I obtained the rootpw with this command: slappasswd -s changeme I also created the /var/lib/ldap/sniejana-sandbox.com directory and made sure the entire contents of /var/lib/ldap were owned by the ldap user. I found two ldap.conf files, one in /etc and one in /etc/openldap. I don't know which is the right one. If I understood correctly, this file is to configure the client. I put this in both: HOST localhost BASE dc=sniejana-sandbox,dc=com I then ran the server with: service slapd start It said OK. Most of the tutorials above say to use the command ldapsearch -D "cn=Manager,dc=my-domain,dc=com" -W to ensure that everything's working. When I execute this command, a password prompt appears, and after entering the password, I get the error. ldapsearch -D "cn=root,dc=sniejana-sandbox,dc=com" -W Enter LDAP password: ldap_bind: Invalid credentials (49) The same thing happens when trying to use ldapadd. I tried with an encrypted and unencrypted password in slapd.conf, it doesn't change anything. Adding a -x for simple authentication doesn't change anything either. netstat -ap confirms the server is listening: tcp 0 0 *:ldap *:* LISTEN 4148/slapd tcp 0 0 *:ldap *:* LISTEN 4148/slapd ps -ef|grep slapd confirms the process is running: ldap 4148 1 0 15:22 ? 00:00:00 /usr/sbin/slapd -h ldap:/// -u ldap Running slaptest procudes config file testing succeeded. I read somewhere that the command ldapsearch -x -b '' -s base '(objectclass=*)' namingContext can confirm the server is running. It appears to work: # extended LDIF # # LDAPv3 # base <> with scope baseObject # filter: (objectclass=*) # requesting: namingContext # # dn: # search result search: 2 result: 0 Success # numResponses: 2 # numEntries: 1 I'm running out of ideas. Am I missing something obvious?

    Read the article

  • How can I troubleshoot Virtualbox port forwarding from Windows guest to OSX host not working?

    - by joe larson
    There are a plethora of questions about virtual box port forwarding problems but none with my specific details. I have a Windows install living in Virtual Box, hosted within OSX. I've got several webservers running on localhost on different ports within the Windows install. I cannot for the life of me get port forwarding to work so I can access those webservers from OSX. My settings look like this (yes I have a NAT adapter): And in my vbox configuration file the relavent portion looks like this: <NAT> <DNS pass-domain="true" use-proxy="false" use-host-resolver="false"/> <Alias logging="false" proxy-only="false" use-same-ports="false"/> <Forwarding name="RLPWeb" proto="1" hostport="7084" guestip="127.0.0.1" guestport="7084"/> <Forwarding name="UtilWeb" proto="1" hostport="4040" guestip="127.0.0.1" guestport="4040"/> <Forwarding name="WCARLP" proto="1" hostport="8084" guestip="127.0.0.1" guestport="8084"/> <Forwarding name="WCAUtil" proto="1" hostport="4848" guestip="127.0.0.1" guestport="4848"/> </NAT> I've turned off the Windows firewall to ensure it is not interfering, and I am not running a firewall on OSX. Anyway, when I attempt to go to for example http://127.0.0.1:4040/ on any of my OSX browsers, it will eventually time out. The log file for this VM shows that it is correctly reading the settings and implying it's doing the right thing here: 00:00:08.286 NAT: set redirect TCP host port 4848 => guest port 4848 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 8084 => guest port 8084 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 4040 => guest port 4040 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 7084 => guest port 7084 @ 127.0.0.1 00:00:08.290 Changing the VM state from 'LOADING' to 'SUSPENDED'. 00:00:08.290 Changing the VM state from 'SUSPENDED' to 'RESUMING'. 00:00:08.290 Changing the VM state from 'RESUMING' to 'RUNNING'. 00:00:08.337 Display::handleDisplayResize(): uScreenId = 0, pvVRAM=000000012017d000 w=1834 h=929 bpp=32 cbLine=0x1CA8, flags=0x1 00:00:09.139 AIOMgr: Host limits number of active IO requests to 16. Expect a performance impact. 00:00:13.454 NAT: DHCP offered IP address 10.0.2.15 I've tried setting the Host IP to 127.0.0.1, and I've tried setting Guest IP blank and also 10.0.2.15. None of these seem to help. What else can I look at to troubleshoot this issue? Details of setup: OSX 10.6.8 Windows 7 Professional 64bit VirtualBox 4.1.2

    Read the article

  • mounting ext4 fs with block size of 65536

    - by seaquest
    I am doing some benchmarking on EXT4 performance on Compact Flash media. I have created an ext4 fs with block size of 65536. however I can not mount it on ubuntu-10.10-netbook-i386. (it is already mounting ext4 fs with 4096 bytes of block sizes) According to my readings on ext4 it should allow such big block sized fs. I want to hear your comments. root@ubuntu:~# mkfs.ext4 -b 65536 /dev/sda3 Warning: blocksize 65536 not usable on most systems. mke2fs 1.41.12 (17-May-2010) mkfs.ext4: 65536-byte blocks too big for system (max 4096) Proceed anyway? (y,n) y Warning: 65536-byte blocks too big for system (max 4096), forced to continue Filesystem label= OS type: Linux Block size=65536 (log=6) Fragment size=65536 (log=6) Stride=0 blocks, Stripe width=0 blocks 19968 inodes, 19830 blocks 991 blocks (5.00%) reserved for the super user First data block=0 1 block group 65528 blocks per group, 65528 fragments per group 19968 inodes per group Writing inode tables: done Creating journal (1024 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 37 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. root@ubuntu:~# tune2fs -l /dev/sda3 tune2fs 1.41.12 (17-May-2010) Filesystem volume name: <none> Last mounted on: <not available> Filesystem UUID: 4cf3f507-e7b4-463c-be11-5b408097099b Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 19968 Block count: 19830 Reserved block count: 991 Free blocks: 18720 Free inodes: 19957 First block: 0 Block size: 65536 Fragment size: 65536 Blocks per group: 65528 Fragments per group: 65528 Inodes per group: 19968 Inode blocks per group: 78 Flex block group size: 16 Filesystem created: Sat Feb 5 14:39:55 2011 Last mount time: n/a Last write time: Sat Feb 5 14:40:02 2011 Mount count: 0 Maximum mount count: 37 Last checked: Sat Feb 5 14:39:55 2011 Check interval: 15552000 (6 months) Next check after: Thu Aug 4 14:39:55 2011 Lifetime writes: 70 MB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: afb5b570-9d47-4786-bad2-4aacb3b73516 Journal backup: inode blocks root@ubuntu:~# mount -t ext4 /dev/sda3 /mnt/ mount: wrong fs type, bad option, bad superblock on /dev/sda3, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

    Read the article

  • APC File Cache not working but user cache is fine

    - by danishgoel
    I have just got a VPS (with cPanel/WHM) to test what gains i could get in my application with using apc file cache AND user cache. So firstly I got the PHP 5.3 compiled in as a DSO (apache module). Then installed APC via PECL through SSH. (First I tried with WHM Module installer, it also had the same problem, so I tried it via ssh) All seemed fine and phpinfo showed apc loaded and enabled. Then I checked with apc.php. All seemed OK But as I started testing my php application, the stats in apc for File Cache Information state: Cached Files 0 ( 0.0 Bytes) Hits 1 Misses 0 Request Rate (hits, misses) 0.00 cache requests/second Hit Rate 0.00 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.00 cache requests/second Cache full count 0 Which meant no PHP files were being cached, even though I had browsed through over 10 PHP files having multiple includes. So there must have been some Cached Files. But the user cache is functioning fine. User Cache Information Cached Variables 0 ( 0.0 Bytes) Hits 1000 Misses 1000 Request Rate (hits, misses) 0.84 cache requests/second Hit Rate 0.42 cache requests/second Miss Rate 0.42 cache requests/second Insert Rate 0.84 cache requests/second Cache full count 0 Its actually from an APC caching test script which tries to retrieve and store 1000 entries and gives me the times. A sort of simple benchmark. Can anyone help me here. Even though apc.cache_by_default = 1, no php files are being cached. This is my apc config Runtime Settings apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 1M apc.mmap_file_mask apc.num_files_hint 1000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.serializer default apc.shm_segments 1 apc.shm_size 32M apc.slam_defense 1 apc.stat 1 apc.stat_ctime 0 apc.ttl 0 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 0 apc.write_lock 1 Also most php files are under 20KB, thus, apc.max_file_size = 1M is not the cause. I have also tried using 'apc_compile_file ' to force some files into opcode cache with no luck. I have also re-installed APC with Debugging enabled, but nothing shows in the error_log I have also tried setting mmap_file_mask to /dev/zero and /tmp/apc.xxxxxx, i have also set /tmp permissions to 777 to no avail Any clue anyone. Update: I have tried following things and none cause APC file cache to populate 1. set apc.enable_cli = 1 AND run a script from cli 2. Set apc.max_file_size = 5M (just in case) 3. switched php handler from dso to FastCGI in WHM (then switched it back to dso as it did not solve the problem) 4. Even tried restarting the container

    Read the article

  • Why does Ubuntu 9.10 hang during boot at "Booting processor 1 APIC 0x1 ip 0x6000"?

    - by BraeburnDev
    I recently installed a new copy of Ubuntu 9.10 (Kernel 2.6.31-14) on to my Hp Pavilion dv6t, so I can setup a Linux development environment. The install went flawlessly and I proceeded with Ubuntu's udate manager's long list of updates (292 in all). I also setup a swap file and activated a Nvidia 185 driver for the Nvidia 260m GPU on the machine. After all this was done I restarted the computer and booted into Ubuntu this time with a newer 2.6.31-19 Kernel which was installed from the update manager. During booth the computer hung at this point: Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013136] Performance Counters: Nehalem/Corei7 events, Intel PMU driver. Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013141] ... version: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013142] ... bit width: 48 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013144] ... generic counters: 4 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013146] ... value mask: 0000ffffffffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013147] ... max period: 000000007fffffff Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013149] ... fixed-purpose counters: 3 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.013151] ... counter mask: 000000070000000f Feb 24 14:23:12 braeburn-laptop kernel: [ 0.015539] ACPI: Core revision 20090521 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052264] Setting APIC routing to flat Feb 24 14:23:12 braeburn-laptop kernel: [ 0.052639] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.152580] CPU0: Intel(R) Core(TM) i7 CPU Q 720 @ 1.60GHz stepping 05 Feb 24 14:23:12 braeburn-laptop kernel: [ 0.270845] Booting processor 1 APIC 0x1 ip 0x6000 I can post a full kern.log of this boot process if requested. Hopefully this is enough information to go on. I should add that I'm still new to configuring and running a Linux OS although I know enough basic command line usage to do software development. This is my attempt to become more familiar with Linux and manage my own system. I'd like to get some insight on the nature of this system hang, what the problem is and how to resolve it. At this point I can scrap the install if I broke something, but my intuition says this is an issue with the kernel recognizing the correct hardware configuration for my system, or perhaps this is an issue with the APIC drivers managing Nehalem's new power management capabilities? Thanks for looking at this issue and providing feed back.

    Read the article

  • FTP not listing files behind firewall (setsockopt (ignored): Permission denied)

    - by KennyDs
    We are developing a Magento application that has a module that works with FTP. Today we deployed this on the testing environment which is setup in the following way: Gateway server which has the following iptables rules: # iptables -L -n -v Chain INPUT (policy ACCEPT 2 packets, 130 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 165 13720 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED Chain FORWARD (policy ACCEPT 7 packets, 606 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- eth1 eth0 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 15 965 ACCEPT all -- eth0 eth1 0.0.0.0/0 0.0.0.0/0 0 0 REJECT all -- eth1 eth1 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 126 packets, 31690 bytes) pkts bytes target prot opt in out source destination These are set at runtime via the following bash script: #!/bin/sh PATH=/usr/sbin:/sbin:/bin:/usr/bin # # delete all existing rules. # iptables -F iptables -t nat -F iptables -t mangle -F iptables -X # Always accept loopback traffic iptables -A INPUT -i lo -j ACCEPT # Allow established connections, and those not coming from the outside iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the LAN side. iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT # Masquerade. iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE # Don't forward from the outside to the inside. iptables -A FORWARD -i eth1 -o eth1 -j REJECT # Enable routing. echo 1 > /proc/sys/net/ipv4/ip_forward The gateway server is connected to the WAN via eth1 and is connected to the internal network via eth0. One of the servers from eth1 has the following problem when trying to list files over ftp: $ ftp -vd myftpserver.com Connected to myftpserver.com 220 Welcome to MY FTP Server ftp: setsockopt: Bad file descriptor Name (myftpserver.com:magento): XXXXXXXX ---> USER XXXXXXXX 331 User XXXXXXXX, password please Password: ---> PASS XXXX 230 Password Ok, User logged in ---> SYST 215 UNIX Type: L8 Remote system type is UNIX. Using binary mode to transfer files. ftp> ls ftp: setsockopt (ignored): Permission denied ---> PORT 192,168,19,15,135,75 421 Service not available, remote server has closed connection When I try listing the files in passive mode, same result. When I run the same command on the gateway server, everything works fine so I believe that the issue is happening because of the iptables rules not forwarding properly. Does anyone have an idea which rule I need to add to make this work?

    Read the article

  • How to know the source of certain TCP traffic on AIX

    - by A.Rashad
    We have two AIX boxes, one for production system and another for testing. both systems are running ATM machine switches, where the ATM device is connected via TCP socket. we had an issue on production system where the machine would power off or get disconnected but the netstat -na | grep <IP of machine > would still mention that the socket is up when simulated that case on the UAT environment, the problem did not happen, where the socket would terminate in 3 to 5 minutes. when sniffed on the traffic between the machine and ATM we found that no traffic takes place on production while there is some sort of heartbeat on UAT. but it is not initiated by the application. $>tcpdump | grep -v "10.2.2.71" | grep -v "HSRP" | grep "10.3.1.30" tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on en6, link-type 1, capture size 96 bytes 09:08:13.323421 IP server073.afs3-callback > 10.3.1.30.impera: . 278204201:278204202(1) ack 3307884029 win 164 09:08:13.335334 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:08:23.425771 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:08:23.425789 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 09:09:13.628985 IP server073.afs3-callback > 10.3.1.30.impera: . 0:1(1) ack 1 win 164 09:09:13.633900 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:09:23.373634 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:09:23.373647 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 while on production, that traffic is not there. we want to know where this traffic is initiated from to implement on production to sense disconnection our comms parameters are: tcp_keepcnt = 2 tcp_keepidle = 100 tcp_keepinit = 150 tcp_keepintvl = 150 tcp_finwait2 = 1200 can anyone help?

    Read the article

  • 64-bit linux kernel only seeing 3 of 4GB after upgrade...

    - by Blaine
    Hey everyone. I am running Ubuntu 9.04 64-bit on my macbook. I had 2GB of ram before, and everything ran great. I just upgraded to 2x2GB (4GB), but my system only sees 3GB of it. OS X, which I am dual booting, sees all 4GB. Also, my video performance is incredibly lacking. Before the upgrade my compiz benchmark was full at 80fps, and now it is at 22fps with very choppy window dragging. Has anyone ever heard of this on a 64-bit kernel? I just don't quite understand what could be the issue. 10$ uname -a Linux macbook 2.6.28-15-generic #49-Ubuntu SMP Tue Aug 18 19:25:34 UTC 2009 x86_64 GNU/Linux $ free -m total used free shared buffers cached Mem: 2953 1031 1921 0 114 427 -/+ buffers/cache: 489 2463 Swap: 7812 0 7812 9$ lsmod Module Size Used by i915 77960 2 drm 123232 3 i915 binfmt_misc 18572 1 ppdev 16904 0 btusb 21784 2 bridge 63776 0 stp 11140 1 bridge bnep 22912 2 vboxnetadp 109356 0 vboxnetflt 116972 0 vboxdrv 1721612 1 vboxnetflt uvcvideo 69640 0 compat_ioctl32 18304 1 uvcvideo videodev 45184 2 uvcvideo,compat_ioctl32 v4l1_compat 23940 2 uvcvideo,videodev lp 19588 0 parport 49584 2 ppdev,lp snd_hda_intel 557492 3 snd_pcm_oss 52352 0 snd_mixer_oss 24960 1 snd_pcm_oss snd_pcm 99464 2 snd_hda_intel,snd_pcm_oss arc4 10240 2 snd_seq_dummy 11524 0 ecb 11392 2 snd_seq_oss 41984 0 snd_seq_midi 15744 0 snd_rawmidi 33920 1 snd_seq_midi snd_seq_midi_event 16512 2 snd_seq_oss,snd_seq_midi snd_seq 66272 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event ath9k 310584 0 snd_timer 34064 2 snd_pcm,snd_seq snd_seq_device 16276 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq mac80211 251528 1 ath9k iTCO_wdt 21712 0 iTCO_vendor_support 12420 1 iTCO_wdt joydev 20992 0 video 29204 0 snd 78920 15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device applesmc 37700 0 output 11648 1 video soundcore 16800 1 snd pcspkr 11136 0 cfg80211 43680 1 mac80211 appletouch 19972 0 isight_firmware 11520 0 input_polldev 12688 1 applesmc intel_agp 39408 1 snd_page_alloc 18704 2 snd_hda_intel,snd_pcm led_class 13064 2 ath9k,applesmc hid_apple 15872 0 usbhid 47040 0 ohci1394 42164 0 ieee1394 108288 1 ohci1394 sky2 63364 0 fbcon 49792 0 tileblit 11264 1 fbcon font 17024 1 fbcon bitblit 14464 1 fbcon softcursor 10368 1 bitblit Some information from dmesg: [ 795.820163] ACPI: EC: GPE storm detected, transactions will use polling mode [ 1762.709516] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 1763.078130] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2362.760889] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2416.352084] ACPI: EC: missing confirmations, switch off interrupt mode. [ 3718.721095] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 3719.108914] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 4318.773266] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 9513.813066] CE: hpet increasing min_delta_ns to 15000 nsec [ 9693.815684] npviewer.bin[6736]

    Read the article

< Previous Page | 805 806 807 808 809 810 811 812 813 814 815 816  | Next Page >