Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 81/172 | < Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >

• sound stopped working after upgrade to 11.10 on Tuesday 20th March

  - by Hugh Barney

  My sound card stopped working after a set of updates were installed 2 days ago. The sound card is detected, the volume is not muted and the speakers work, I can make the speakers hum if I touch the jack plug lead that normally plugs into the card. hugh@lindisfarne:~$ lspci -v | grep -A7 -i "audio" 07:01.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster Subsystem: Creative Labs SB0570 [SB Audigy SE] Flags: bus master, medium devsel, latency 32, IRQ 16 I/O ports at c000 [size=32] Capabilities: Kernel driver in use: CA0106 Kernel modules: snd-ca0106 I've tried reverting those upgraded packages that look like the could impact the kernal - but to no avail. alsamixer does not have anything muted, I've been though all the sound card debug/troubleshooting pages I can find. Kernal driver is attached. So whats gone pop ? I will boot from CD to check - but I am pretty sure this is a sw and not a hw problem.

  Read the article

• mount old ATA disk to USB adapter

  - by 213441265152351

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic USB-IDE, an ATA adapter to USB 1.0 similar to the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. Any ideas?

  Read the article

• USB Mouse sleeping after 5 seconds when on battery

  - by yurividal

  My usb mouse sleeps after 5 seconds of inactivity when running on battery power. It wakes uo again when i press any button on the mouse. This is really annoying. I have made lsusb, and I noticed my mouse is Bus 001 Device 012: ID 04d9:2083 Holtek Semiconductor, Inc. I have checked my /sys/bus/usb/devices/usb1/power/autosuspend but it is already set to 0, and the directory usb1 has many subdirectories which also have autosuspend files, and i dont know how to edit them. Also, I would like a permanent solution, which would work for any mouse, on any of my 3 usb ports. Any ideas? Using: Ubuntu 12.04 64bit

  Read the article

• Wireless networks are not detected at start up in Ubuntu 12.04

  - by Kanhaiya Mishra

  I have recently (three four days ago) installed Ubuntu 12.04 via windows installer i.e. wubi.exe. After the installation completed wireless and Ethernet were both working well. But after restart wireless networks didn't show up while in the network manager both networking and wireless were enabled. Though sometimes after boot it did show the networks available but very rarely. So I went through various posts regarding wireless issues in Ubuntu 12.04 and tried so many things but ended up in nothing satisfactory. I have Broadcom 4313 LAN network controller and brcmsmac driver. Then relying on some suggestions I tried to install bcm-wl driver but couldn't install due to some error in jockeyl.log file. Then i tried fresh installation of the same driver but still could resolve the startup issues with wireless. Then again I reinstalled Ubuntu inside windows using wubi installer. This time again same problem occurred after boot. But this time I successfully installed wl driver before disturbing file-system files of Ubuntu. But again the same issue. This time I noticed some new things: If I inserted Ethernet/LAN cable before startup then wireless networks are available and of course LAN(wired) networks also work. but if i don't plug in cable before startup and then plug it after startup then it didn't detect Ethernet network neither wireless. So I haven't noticed it before that LAN along with wifi also doesn't work after startup. But if i suspend the session and make it sleep and again login then it worked. I tried it every time that WLAN worked perfectly. But still i m unable to resolve that startup problem. Each time i boot first I have to suspend it once then only networks are available. It irritates me each time i reboot/boot my lappy. So please help out of this problem. Any ideas/help regarding this issue would be highly appreciated. Some of the commands that i run gave following results: # lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) # sudo lshw -C network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:49:b6:ab width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.1.7 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: b8:ac:6f:6b:f7:4a capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) # lsmod | grep wl wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl # sudo iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 30:46:9A:85:DA:9A ESSID:"BH DASHIR 2" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:4/5 Signal level:-60 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B000103104700109AFE7D908F8E2D381860668BA2E8D8771021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: C0:3F:0E:EB:45:14 ESSID:"BH DASHIR 3" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-71 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B00010310470010F3C9BBE499D140540F530E7EBEDE2F671021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 03 - Address: A0:21:B7:A8:2F:C0 ESSID:"BH DASHIR 4" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:1/5 Signal level:-86 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD8B0050F204104A0001101044000102103B0001031047001000000000000010000000A021B7A82FC01021000D4E6574676561722C20496E632E10230009574E523130303076321024000456324831104200046E6F6E651054000800060050F20400011011001B574E5231303030763228576972656C6573732041502D322E344729100800020086103C000103 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s

  Read the article

• Thinkpad T530 with Optimus and Docking Station

  - by Vic Boudolf

  I have a Lenovo Thinkpad T530 with Optimus video, which is not supported on 12.04.1. I don't normally need the discrete (nVidia) graphics, so I turn it off in the BIOS settings to achieve longer battery life (and so that the screen dimmer will work), but when placed in the docking station, the integrated (Intel) graphics don't power the HDMI ports. (The VGA port does work, but I want to focus on the HDMI.) This means I have to change the BIOS settings constantly. Is there any way to have the system detect the docking station and power up/enable the discrete graphics accordingly? I don't need to do it on the fly. Just at startup. This post suggests that bumblebee can turn the discrete graphics on and off for specific applications, but I just want to turn it on or off. [2 suggests that vga_switcheroo will not work with nVidia Optimus.

  Read the article

• Ubuntu 12.04 + Wifi not working

  - by user171154

  i'm having problems connecting over wireless. At the moment, I'm using wicd. It seems to get stuck on "Verifying AP association...". Without wicd I can get the connection up and ping the Net - but if I take eth0 down (ifconfig eth0 down), my wireless goes away too (same result if I unplug the wire instead). wicd is the only way I can bring eth0 back (which is the main reason I'm using it) - ifconfig eth0 and/or ifup eth0 do not re-enable the connection (I just discovered it leaves out the gateway. Adding the gateway back in re-enables the connection including wifi; I didn't want to delete the info about wicd above in case it gives someone an idea.) Doing it manually, despite the errors (which it would be nice to also resolve) - allows me to ping the outside world: ifup wlan0 ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument ssh stop/waiting ssh start/running, process 17336 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_req=1 ttl=43 time=48.8 ms 64 bytes from 8.8.8.8: icmp_req=2 ttl=43 time=47.9 ms 64 bytes from 8.8.8.8: icmp_req=3 ttl=43 time=48.7 ms 64 bytes from 8.8.8.8: icmp_req=4 ttl=43 time=53.2 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3003ms rtt min/avg/max/mdev = 47.975/49.711/53.235/2.063 ms # iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TPLINK" Mode:Managed Frequency:2.427 GHz Access Point: 64:66:xx:xx:xx:22 Bit Rate=108 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=70/70 Signal level=-39 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: f0:7d:68:c1:b4:13 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-67-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:dfbf0000-dfbfffff ip route default via 192.168.0.1 dev eth0 default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 (For the record, I have no idea what the 169.254.0.0 address is doing there.) uname -a 3.2.0-67-generic-pae #101-Ubuntu SMP Tue Jul 15 18:04:54 UTC 2014 i686 i686 i386 GNU/Linux lshw -C network *-network description: Ethernet interface product: NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 01 serial: 00:11:11:59:fc:09 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5751-v3.23a ip=192.168.0.102 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:dfcf0000-dfcfffff *-network description: Wireless interface product: AR5418 Wireless Network Adapter [AR5008E 802.11(a)bgn] (PCI-Express) vendor: Qualcomm Atheros physical id: 0 /etc/network/interfaces # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback source /etc/network/interfaces.eth0 source /etc/network/interfaces.wlan0 /etc/network/interfaces.eth0 #Main Interface auto eth0 iface eth0 inet static address 192.168.0.102 netmask 255.255.255.0 gateway 192.168.0.1 /etc/network/interfaces.wlan0 auto wlan0 iface wlan0 inet static address 192.168.0.12 gateway 192.168.0.1 dns-nameservers 192.168.0.1 8.8.8.8 netmask 255.255.255.0 wpa-driver wext wpa-ssid TPLINK wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk dca1badb5fd4e9axxx4xxdaaxxfa91xx610bxx6a7d57ef67af9809dxx6af42e39 /etc/wpa_supplicant.conf ctrl_interface=/var/run/wpa_supplicant network={ ssid="TPLINK" psk="my password" key_mgmt=WPA-PSK proto=RSN pairwise=CCMP group=CCMP } ifdown eth0 ifdown: interface eth0 not configured ifconfig eth0 Link encap:Ethernet HWaddr 00:11:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:213690 errors:0 dropped:0 overruns:0 frame:0 TX packets:155266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:220057808 (220.0 MB) TX bytes:21137696 (21.1 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196412 errors:0 dropped:0 overruns:0 frame:0 TX packets:196412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270697 (153.2 MB) TX bytes:153270697 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11335 errors:0 dropped:0 overruns:0 frame:0 TX packets:7287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2563290 (2.5 MB) TX bytes:855746 (855.7 KB) ifconfig eth0 down ifconfig eth0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:09 inet addr:192.168.0.102 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:11ff:fe59:fc09/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:192 (192.0 B) TX bytes:94 (94.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:196418 errors:0 dropped:0 overruns:0 frame:0 TX packets:196418 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:153270871 (153.2 MB) TX bytes:153270871 (153.2 MB) wlan0 Link encap:Ethernet HWaddr f0:7d:xx:xx:xx:13 inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f27d:68ff:fec1:b413/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11359 errors:0 dropped:0 overruns:0 frame:0 TX packets:7293 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2565482 (2.5 MB) TX bytes:856363 (856.3 KB) ip route default via 192.168.0.1 dev wlan0 metric 100 169.254.0.0/16 dev wlan0 scope link metric 1000 192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.12 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.102 ping -I wlan0 -c 4 8.8.8.8 PING 8.8.8.8 (8.8.8.8) from 192.168.0.12 wlan0: 56(84) bytes of data. --- 8.8.8.8 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3024ms ping -I eth0 -c 3 router PING router (192.168.0.1) from 192.168.0.102 eth0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2015ms ping -I wlan0 -c 3 router PING router (192.168.0.1) from 192.168.0.12 wlan0: 56(84) bytes of data. --- router ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2014ms Let me know if you need more info. Thank you in advance.

  Read the article

• Cisco Linksys AE2500 wireless adapter not working

  - by makuto

  I have a Cisco AE2500 I've used with my laptop to get internet. I had to install the drivers by following this forum: http://ubuntuforums.org/showthread.php?t=1805830 But now the blue light on the adapter doesn't turn on at all, but ndiswrapper reports it is connected. I have no connection to the internet on my laptop, and the adapter doesn't show it's blue light on any of the USB ports of my computer or on the 4 port hub I have. Is there some way I can reset something so that the blue light will show again? I'm using Ubuntu 11.10 on a Dell Latitude D505 laptop. EDIT: I deleted and reinstalled the same exact driver and everything worked again.

  Read the article

• Content Manager Assistant PSVita Linux Does NOT Recognize USB Port

  - by Nicky Bailuc

  I have an external copy of Windows 7 alongside Quantal and I installed Content Manager Assistant on it. I was able to start the program successfully by finding the Executable file of the program in the program folder in Windows and run it in Wine, however Wine didn't recognize my PSVita that was connected through one of my USB ports. Is there any way to configure WINE to properly recognize the Vita? Content Manager Assistant is a Windows and Mac only program that allows you to transfer files between your PC and PSVita, kinda like iTunes for iPod.

  Read the article

• FTP over ssh hangs on "Connection established: Waiting for Welcome Message"

  - by Siriss

  I have looked far and wide and have not quite found the answer. I am running ubuntu 11.10, openssh, and vsftpd. I am trying to configure my FTP to tunnel over ssh. My ssh connection works just fine and I can create the tunnel to my FTP port. When I go to use Filezilla to connect, it hangs at "Waiting for Welcome Message". I think it is an iptables issue, but I can't seem to figure out what needs to be changed. When I take iptables down, it connects just fine. I don't want to open any more external ports, just my one SSH port, and I can't seem to get it right on the internal port forwarding rule. I always end up opening it to the outside. I would love some help if anyone has any ideas and I hope I have made it clear. Thank you in advance!!

  Read the article

• RPi and Java Embedded GPIO: Connecting LEDs

  - by hinkmond

  Next, we need some low-level peripherals to connect to the Raspberry Pi GPIO header. So, we'll do what's called a "Fry's Run" in Silicon Valley, which means we go shop at the local Fry's Electronics store for parts. In this case, we'll need some breadboard jumper wires (blue wires in photo), some LEDs, and some resistors (for the RPi GPIO, 150 ohms - 300 ohms would work for the 3.3V output of the GPIO ports). And, if you want to do other projects, you might as well by a breadboard, which is a development board with lots of holes in it. Ask a Fry's clerk for help. Or, better yet, ask the customer standing next to you in the electronics components aisle for help. (Might be faster) So, go to your local hobby electronics store, or go to Fry's if you have one close by, and come back here to the next blog post to see how to hook these parts up. Hinkmond

  Read the article

• Port 21 will not open. status is closed. forward port 21 to new domains.

  - by Bob Swaggerty

  I am having a problem opening port 21 on my Linux Ubuntu server. No matter what i do, i can not get my status to change from closed to open. Here is a recent iptables command i used and the result iptables -A INPUT -p tcp -m tcp --dport 21 -j ACCEPT nmap -p21-22,25,80,443 CCR1 Starting Nmap 4.53 ( http://insecure.org ) at 2012-06-19 03:13 CDT Interesting ports on CCR1.chennaichristianradio.com (5.10.69.98): PORT STATE SERVICE 21/tcp closed ftp 22/tcp open ssh 25/tcp closed smtp 80/tcp open http 443/tcp closed https I also used commands from the advise from this forum http://www.cyberciti.biz/faq/iptables-open-ftp-port-21/ I need to open this for FTP access to the server, and ultimately I need to forward port 21 to 2 domains i am setting up. Thank you for any assistance you can provide -Bob Swaggerty

  Read the article

• Is there a way to disable a particular pci port

  - by mxdog

  I have a MB with 2 nics on it. a switch burned up and took out one of them. there is no way to turn them off individually in the bios. is there a way to turn off one of the ports. unmap it,unbind it, power it down so the system doesnt see it at after boot. they are mapped as 0000:02.08.0 and 0000:02.08.1 I want to turn the second one off somehow. Since they both use the same driver, blacklisting the module will take out both of them. Normally I would just live with it but it seems there should be a way to do that like in windows (gasp)--just disable it. I Actually have the exact same problem on another comp running XCP so this will be a 2fer if it gets figured out. the OS is 12.4 lts server with xen on it. THX

  Read the article

• trying live-usb 12.04.1 image on an old desktop

  - by 213441265152351

  I am trying to load Ubuntu 12.04.1 32-bit desktop image on an old desktop computer. The system shows the initial menu, but after a while, I get an error like the one in the following two screenshots (it takes a few seconds to go from one to the other in the screen): I tried to load it using the different USB ports at the back of the computer, just in case, and I get basically the same error. Find another screenshot from another try: Any ideas what might be happening? NOTES: I checked the md5sum of the iso file to be e235b63c02644e219b7bf3668f479c9e *ubuntu-12.04.1-desktop-i386.iso. I did the 'Test' on the laptop where I created the USB drive, and it loads up correctly. The desktop computer in question is an old AMD Duron 1800MHz with 512MB RAM. I ran a memtest on the computer, and all went fine.

  Read the article

• MAMP Pro Installed On Mavericks 10.9

  - by cnps

  I have MAMP Pro Installed. I'm well aware with the advanced features of MAMP Pro I can change to different types of Hosts, but I wanted to know why my previous method would not work within mavericks. This was my usual working method in 10.8, but now with 10.9 it's a headache. The previous method would: Write a custom address with the host address: "#Virtual Hosts" 127.0.0.1 nameofsite.local go to /Applications/MAMP/conf/apache and open the httpd.conf file, scroll to the bottom and then add NameVirtualHost * DocumentRoot "/Applications/MAMP/htdocs" ServerName localhost DocumentRoot "/Users/Klimt/Sites/siteoffolder" ServerName clientA.local make sure the ports is set to 80, 443, 3306. reset MAMP PRO and then usually type in the url address and it's gold from there. any help?

  Read the article

• Ubuntu 14.04 doesn't detect my discrete GPU

  - by user258887

  I recently purchased a laptop with an Nvidia GeForce 860m, and have installed Ubuntu 14.04. On my old laptop I had 12.04, which automatically filled Additional Drivers with Nvidia drivers. But on this computer, the only thing in Additional Drivers is Qualcomm. So I manually installed Nvidia, but X Server Settings doesn't seem to detect any GPU... lspci | grep VGA reports only my integrated Intel GPU, but lspci -v reports many things, including the Nvidia GPU: 01:00.0 3D controller: NVIDIA Corporation GM107M [GeForce GTX 860M] (rev a2) Subsystem: ASUSTeK Computer Inc. Device 157d Flags: fast devsel, IRQ 16 Memory at ec000000 (32-bit, non-prefetchable) [size=16M] Memory at c0000000 (64-bit, prefetchable) [size=256M] Memory at d0000000 (64-bit, prefetchable) [size=32M] I/O ports at e000 [size=128] Expansion ROM at ed000000 [disabled] [size=512K] Capabilities: access denied Don't know what any of that means. Not sure if it's supposed to say 'access denied'... I need my GPU to do CUDA and OpenGL programming. What else can I do to figure out why this isn't working?

  Read the article

• Getting front audio jacks to work

  - by Ashfame

  I run Ubuntu 10.10 on my Intel D945. My front audio ports don't work in Ubuntu, the rear one does. I never got it working earlier when I had Ubuntu 10.04 but this time I am going to try it again. My codec is SigmaTel STAC9227 My ALSA information is here. Handy details: !!ALSA Version !!------------ Driver version: 1.0.23 Library version: 1.0.23 Utilities version: 1.0.23 !!Loaded ALSA modules !!------------------- snd_hda_intel snd_hda_intel I know something that I will have to change the model of my module to make the front audio jack works but I couldn't find a model related line in my ALSA configuration file - /etc/modprobe.d/alsa-base.conf (I was able to get to that point in Ubuntu 10.04, may be something has changed). How can I proceed from here?

  Read the article

• At what point is asynchronous reading of disk I/O more efficient than synchronous?

  - by blesh

  Assuming there is some bit of code that reads files for multiple consumers, and the files are of any arbitrary size: At what size does it become more efficient to read the file asynchronously? Or to put it another way, how small must a file be for it to be faster just to read it synchronously? I've noticed (and perhaps I'm incorrect) that when reading very small files, it takes longer to read them asynchronously than synchronously (in particular with .NET). I'm assuming this has to do with set up time for things like I/O Completion Ports, threads, etc. Is there any rule of thumb to help out here? Or is it dependent on the system and the environment?

  Read the article

• E3 2012 : Tout savoir sur la Wii U : les caractéristiques de la console de Nintendo, les jeux et autres détails

  Tout savoir sur la Wii U Les caractéristiques, les jeux, les détails et le reste À l'occasion de l'E3, nous avons pu apprendre beaucoup sur la Wii U, la prochaine console de Nintendo. Commençons tout d'abord par les caractéristiques de la machine : Machine :[IMG]http://jeux.developpez.com/news/images/WiiU.jpg[/IMG] 4.57 cm de hauteur sur 26.67cm en longueur sur 17.2cm de large ; 1.5kg ; le processeur est basé sur un IBM Power ayant plusieurs coeurs ; la carte graphique est basée sur AMD Radeon HD mémoire flash, supporte aussi les cartes SD et possède quatre ports USB (deux à l'avant et deux à l'arrière) ; lec...

  Read the article

• How to print over ssh?

  - by mit

  I have the following configuration: P == U ---------------- W P is a HP Laserjet, connected to U, which is an Ubuntu 10.04 desktop machine with a standard gnome setup from the live cd. I just selected the HP Laserjet in the gnome printer admin and it works, I can print locally. W is a remote windows machine, server 2003, and --- is an untrusted connection. I wonder if I can create an ssh tunnel between U and W, so W can print using U's printer service. Which ports will I need to forward and what kind of printer must I add then on the windows machine?

  Read the article

• Juju instances in aganet-state: down after turning them off (and back on) on EC2

  - by Tyler McAdams

  I turned my Juju instances off on EC2 for a while and after bringing them back online they seem to be in an odd state: [code] claude-vm@claude-vm-fusion:~/Documents/Shell Scripts$ juju status 2012-11-17 17:06:44,094 INFO Connecting to environment... 2012-11-17 17:06:45,590 INFO Connected to environment. machines: 0: agent-state: not-started dns-name: ec2-54-242-142-196.compute-1.amazonaws.com instance-id: i-b0996fcf instance-state: running 1: agent-state: down dns-name: ec2-50-19-186-245.compute-1.amazonaws.com instance-id: i-8c8375f3 instance-state: running 2: agent-state: down dns-name: ec2-54-242-255-238.compute-1.amazonaws.com instance-id: i-56807629 instance-state: running services: wordpress: charm: cs:precise/wordpress-9 exposed: true relations: db: - wordpress-db loadbalancer: - wordpress units: wordpress/0: agent-state: down machine: 2 open-ports: - 80/tcp public-address: ec2-54-242-227-57.compute-1.amazonaws.com wordpress-db: charm: cs:precise/mysql-10 relations: db: - wordpress units: wordpress-db/0: agent-state: down machine: 1 public-address: ec2-54-242-212-177.compute-1.amazonaws.com 2012-11-17 17:06:47,274 INFO 'status' command finished successfully [/code] Can I not take my instances down for a while? Or is this something else?

  Read the article

• Wake-on-lan under Ubuntu 12.04

  - by iUngi

  I would like to setup the wake-on-lan, the two PCs are connected through a switch. Here is the configuration of the eth0, in the BIOS I couldn't find any information regarding the wake-on-lan. Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: MII PHYAD: 0 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000033 (51) drv probe ifdown ifup Link detected: yes After I shut down the PC, I used different tools to send out the magic package, but nothing happens. Any suggestion?

  Read the article

• Kubuntu - Roccat keyboard does not work under GRUB and works partially in BIOS

  - by Donald_W

  The system specification GRUB boot loader OS: Windows 7 / Kubuntu 12.04 LTS Keyboard: Roccat Isku Motherboard: MSI Z77 MPower with the latest BIOS SSD/HDD: Kingston HyperX 3K (AHCI in BIOS enabled), 2 other HDDs I will provide more specific configuration if needed. The problem As stated in the topic I cannot navigate in the GRUB menu using mentioned keyboard (there is no problem when I use Logitech K360). I have tried both USB 2.0 and USB 3.0 ports. I cannot enter BIOS menu as well, however if I enter it using other keyboard, Roccat seems to work and I can navigate in the BIOS menu without any issues. Any ideas how can I fix that problem?

  Read the article

• Why does Facebook convert PHP code to C++?

  - by user72245

  I read that Facebook started out in PHP, and then to gain speed, they now compile PHP as C++ code. If that's the case why don't they: Just program in c++? Surely there must be SOME errors/bugs when hitting a magic compiler button that ports PHP to c++ code , right? If this impressive converter works so nicely, why stick to PHP at all? Why not use something like Ruby or Python? Note -- I picked these two at random, but mostly because nearly everyone says coding in those languages is a "joy". So why not develop in a super great language and then hit the magic c++ compile button?

  Read the article

• Mouse Problem on Ubuntu 12.10

  - by KashmirHackers

  I had a strange mouse problem on Ubuntu 12.10(64-Bit), the problem is that when I turnoff power supply/power goes off, the red laser light of my mouse also goes off and my mouse stops working but it works fine when A/C power supply is on. First I thought my mouse or my laptop's USB ports had problem but since I am using Dual Boot with windows 7, I checked my mouse on windows 7 and it works fine, even I turn off power supply. Today,I thought that I should give a try to Linux Mint 14-RC (which is based on same Ubuntu 12.10) and after installing linux mint when I plugged in my mouse it worked fine even though power is off. Don't know what is really going on, and I am afraid if I reinstall my Ubuntu 12.10 the problem will remain.

  Read the article

• Well supported Hardware Raid Controller

  - by ftiaronsem

  I am currently planning to buy a hardware-raid controller. This became necessary since I am running Linux and Windows in parallel and now need the redundancy for both OS (Im am going to use RAID1 / Mirroring). Therefore I am searching for a hardware raid controller which is well supported by linux / ubuntu (reporting smart values, stats for the harddrives, etc...). This controller should have four sata ports and if possible it should fit in a PCIE-1x Slot. I would greatly appreciate, if you could suggest some devices. Thanks in advance

  Read the article

< Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >