Search Results

Search found 25391 results on 1016 pages for 'update notification'.

Page 816/1016 | < Previous Page | 812 813 814 815 816 817 818 819 820 821 822 823  | Next Page >

• No partition on USB Flash Drive?

  - by Skytunnel

  A friend gave me a corrupted USB memory stick to try recovery data from. But I've had some unusual results, so thought I'd share to see if anyone is familiar with this problem... First off I just tried opening from my own PC. Windows prompted to Format the drive, which I of course declined Downloaded TestDisk to anaylsis the drive. And right away I noticed something strange, on the listed drives it comes up as Disk /dev/sdc - 6144 B - USB Flash Drive That's right, the first USB flash drive smaller than a floppy disk!? Moving on anyway... first anaylsis comes up with: Partition sector doesn't have the endmark 0xAA55 TestDisk's Quick Search gave no results, moved on to Deeper Search: No partition found or selected for recovery This left me stumped. I tired a couple of other programs with no success I did manage to get a backup image, but it was just as small as TestDisk indicated, so nothing of use on it After a few hours trying various suggestions from other sources, I gave in and just tried formatting the drive. But returned the message: Windows was unable to complete the format. From googling that, the suggestion was to delete the partition. But there is no partition to delete in this case. most recently I've tried formatting from cmd, and got this result: Format D: /FS:FAT32 The type of the file system is RAW The new file system is FAT32 Verifying 0M 11 bad sectors were encountered during the format. These sectors cannot be guaranteed to have been cleaned The volume is too small for FAT32 Anyone got any suggestions? UPDATE: As per suggestion from @Karen, I tried running a CLEAN from DISKPART, results as follows DiskPart has encountered an error: The request could not be preformed because of an I/O device error.

  Read the article

• Network driver for Hyper-V restore from Windows Home Server

  - by Philipp Schmid

  I have backed up Windows Server 2008 running virtualized on Hyper-V to a Windows Home Server 2008 SP1 (I know I should have backed up the VHD instead). Now I need to restore the contents of the VM from WHS. I have created a restore CD ISO and used it to create a new VM. It all works as advertised up to the point where the restore process wants to load the network drivers (it only finds 4 disk drivers on the restore CD. but no network drivers). So I created a virtual floppy and copied the contents of 'Home Server Drivers for Restore onto it. But no luck! I have tried moving the 4 subdirectories into the root of the floppy, but that didn't work either. Finally, I started another instance of the WS 2008 to identify the network driver that the virtualized instance is using (%WINDOWS%\system32\drivers\netvsc60.sys) and copied that file onto the virtual floppy, without success. Does anyone have any suggestions on how to get networking working on a Hyper-V instance running off the Windows Home Server Restore CD? UPDATE: As suggested by delenda, I have added a legacy network adapter to my VM, and indeed I now get a network driver listed! However, the WHS it still not found, even after entering the home server name manually. PHS

  Read the article

• All computers on network get stuck waiting for some sites indefinetely

  - by zacaj

  This happens across three computers, running windows 7 and Ubuntu, firefox, opera, and chrome (all latest versions). I am connected to the internet through a Verizon wireless usb modem. When I try to open some web pages they will never finish loading (and usually never even show anything). The status bar at the bottom of the browser will display "Waiting for X" The servers it gets stuck on include: platform.twitter.com s7.addthis.com connect.facebook.net ajax.googleapis.com 2mdn.net Ive been getting away with just blocking them in AdBlock up until now, however the last two have been causing problems. There are some sites which require googleapis.com to load correctly, and some that wont ever load unless its blocked. eBay requires access to 2mdn.net to load pictures. On top of this its getting really annoying having to update AdBlock across all these computers whenever a new site pops up. I'm hoping there's some easier way to fix this? The different sites causing the freeze indicate to me that it's either a problem on my end (somehow?) or some server side software that got updated with a new bug?

  Read the article

• Website latency and bad tcp packets

  - by Mistero Lupo

  I have multiple websites hosted on a Linode VPS and I'm having an issue with one of them: every page that I try to load has about 10 seconds latency. Apache logs are clean and the other websites on the same machine are running well. At a first glance I tought it was a memory problem since the VPS has got only 512M, but from the linode dashboard CPU and Disk I/O are normal. Anyway here we have the ram status: $ free -m total used free shared buffers cached Mem: 487 463 23 0 2 55 -/+ buffers/cache: 404 82 Swap: 255 155 100 Only 23M free, but if it was a memory problem why other websites are going as usual? I took a live capture with wireshark, and there are some duplicates SYN ACK packets just before the 10 seconds gap. I'm out of ideas, looking for some clues. Wireshark live capture screenshot As you can see from the image, the gap is after the last bad tcp. Thank you in advance. UPDATE I've checked Apache2 logs in debug error level, and this is where something is appening: 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'index.php' 151.97.156.191 - - [14/Nov/2012:11:19:40 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6801578/subreq] (1) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] pass through /home/fmaisi/sites/www.fmaisi.it/public_html/index.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] strip per-dir prefix: /home/fmaisi/sites/www.fmaisi.it/public_html/wp-content/plugins/wp-filebase/wp-filebase_css.php -> wp-content/plugins/wp-filebase/wp-filebase_css.php 151.97.156.191 - - [14/Nov/2012:11:19:54 +0100] [www.fmaisi.it/sid#7f32c625a220][rid#7f32c6537c78/initial] (3) [perdir /home/fmaisi/sites/www.fmaisi.it/public_html/] applying pattern '^index\.php$' to uri 'wp-content/plugins/wp-filebase/wp-filebase_css.php' As you can see there is a gap of 14 seconds after the pass through of index.php. Any suggestions? I'm out of ideas again.

  Read the article

• 412 Precodition Failed error only occurs on certain networks

  - by Andy

  One of my favorite websites: http://jessiejofficial.com (yes, I'm a Jessie J Fan :')) has recently started displaying the error message "412 Precondition Failed" whenever I visit it from my home network, even when I use Tor Browser. At first I thought that this was an issue with the whole website, however I have contacted the web developer and he has said that they has been plenty of hits within the last 48 hours. Plus, I discovered tonight that I can access the website from my phone, through the mobile network. So it appears to just be my network as all of the devices in my house connected to the WiFi display the same error when I try to visit any page of the site. However there have been no changes that we are aware of or are noticeable to our network since the website was accessible, and I have just heard that another person in a different part of the country is experiencing the same difficulties also. Any help/advice/suggestions would be appreciated greatly Update: When trying to ping 'jessiejofficial.com' in Windows command prompt the request times out on all four attempts, on any computer connected to the wireless network. I can now also confirm that the same thing occurs on my MacBook Pro.

  Read the article

• powershell vs GPO for installation, configuration, maintenance

  - by user52874

  My question is about using powershell scripts to install, configure, update and maintain Windows 7 Pro/Ent workstations in a 2008R2 domain, versus using GPO/ADMX/msi. Here's the situation: Because of a comedy of cumulative corporate bumpfuggery we suddenly found ourselves having to design, configure and deploy a full Windows Server 2008R2 and Windows 7 Pro/Enterprise on very short notice and delivery schedule. Of course, I'm not a windows expert by any means, and we're so understaffed that our buzzword bingo includes 'automate' and 'one-button' and 'it needs to Just Work'. (FWIW, I started with DEC, then on to solaris and cisco, then linux of various flavors with a smattering of BSD nowadays. I use Windows for email and to fill out forms). So we decided to bring in a contractor to do this for us. and they met the deadline. The system is up and mostly usable, and this is good. We would not have been able to do this. But it's the 'mostly' part that is proving to be the PIMA now, and I'm having to learn Microsoft stuff anyway until/if we can get a new contract with these guys for ongoing operations. Here's my question. The contractor used powershell almost exclusively for deployment, configuration and updating. My intensive reading over the last week leads me to think that the generally accepted practices for deployment, configuration and updating microsoft stuff uses elements of GPOs and ADMX templates, along with maybe some third party stuff like PolicyPak. Are there solid reasons that I've not found yet that powershell scripts would be preferred over the GPO methods? I'm going to discuss this with the contractor lead when he gets back from his vacation, and he'll be straight with me (nor do I think they set us up). But I can also see this might be a religious issue, so I would still like some background on this. Thoughts? or weblinks? Thanks!

  Read the article

• Active Directory server down, recovering without reinstalling

  - by whatever

  My Windows 2003 server suddenly ceased to function as a DC (this server is the only DC of the domain). All AD related services are down. The only way I can login to the AD is physically to the machine. Everytime I access an AD-related service (e.g. "AD users and computers") I get the below error: Naming information cannot be located because: The specified directory service attribute or value does not exist. Contact your system administrator to verify that your domain is properly configured and is currently online. I found the below system event which matches the time when the issue started, this re-occurs everytime I reboot the server. NTDS General | Global Catalog | Active Directory was unable to establish a connection with the global catalog. Additional Data Error value: 1355 The specified domain either does not exist or could not be contacted. Internal ID: 3200d33 I started the troubleshooting with DNS. Netdiag throws the below error although I think this is simply a consequence of not being able to access the Global Catalog. The procedure entry point DnsGetPrimaryDomainName_UTF8 could not be located in the dynamic link library DNSAPI.dll. Anyway DNS seems OK because I can ping the DC FQDN from the DC itself. I found the below solution which is supposed to help by doing some cleanup of the metadata: http://support.microsoft.com/kb/216498 If I follow procedure 1 here is what I get at step 9: no current site Domain - DC=<mydomain>,DC=<com> no current server no current naming context I can continue the procedure until step 14. I haven't tested step 15 as my understanding is that I will have to reinstall the whole AD again. Is there any way I can recover my AD from there without having to reinstall the whole thing? Update: Yes, the server was powered off/on because reboot would take forever (not because I thought power cycling the unit would fix it more than a reboot).

  Read the article

• RDP suggesting a user name when connecting to a server

  - by Neolisk

  Prior to Event X, RDPing to Server 2003 always caused the user name appear blank and Login to be enabled, so you could pick to which domain you would log in. For us it's either local or our domain. Since a recent Event X a domain + user name is being suggested for every server and it's not the most recently used user name. If you remove it manually from RDP dialog, it's still being pre-populated for you, and then at the next available opportunity it returns into General/User name option of RDP dialog. So user name field comes pre-populated and you cannot change to log in locally (only if you manually erase domain specifier - everything before \) - Log in to option is disabled by default. We did not do any changes to our domain or client machines, so I am suspecting some Windows update caused it (and this being Event X). Interesting fact - it does not consistently happen on all machines, and some can login to some servers fine, while other servers keep suggesting a default user name. What could be that Event X and is there a way to fix it? EDIT: I tried this - How to clear remote desktop connections history and specifically this part of it: reg delete "HKEY_CURRENT_USER\Software\Microsoft\Terminal Server Client\UsernameHint" /f The problem still persists.

  Read the article

• Recovering data from an external hard drive

  - by CCallaghan

  I have a WD Elements 2GB hard drive (formatted NTFS). I accidentally kicked out the USB cable while writing data to the disk, and now I can't access most of the data. Although this was ostensibly my backup drive, there is a great deal of important material on there which was only on there. I realise how idiotic this makes me. (So, formatting is not an option.) Things I've tried/information I've gathered: Windows Explorer will recognise the drive itself. However, it will not access most directories therein (and will sometimes crash when exploring). I can access all of the directories through the command line, but the dir command will often report that it can't read any files in most of the directories. The situation was similar when I hooked it up to an Ubuntu machine: the file explorer crashed, but I could access directories - but not files in those directories - via terminal commands. Several files I tried to copy out either resulted in an I/O error being reported or resulted in the command line crashing. The Disk Management utility on Windows reports a healthy disk formatted as NTFS and not RAW. It also indicates the correct amount of space used up and its capacity (so it seems that the files are not deleted). I've tried to run chkdsk, but that hangs on Step 2 (checking indexes) at 74%. Step 1 reported no bad sectors. I tried Recuva, but that didn't seem to work (stalled at 0% for half an hour). I should also note that the disk doesn't seem to be spinning smoothly; it seems to be chopping back, like it's reading the same sector over and over again. I noticed this after I kicked out the cable. Any help would be greatly appreciated. Update: It would seem the problem has taken a turn for the worse. The external hard drive now shows up on my computer as a local disk and is not mountable by Linux.

  Read the article

• CMSs & ERPs for hospital management system

  - by Akshey

  Hi, What are the best free CMSs or CMS plugins or ERPs or any other free tools available for developing a hospital management system? I want to develop it for a children's hospital run by my father. The hospital is small with two doctors. Currently, everything is done manually on paper. The main entities who will be using the system are: Receptionist, the two doctors, chemist and the medical laboratorist. They will use it majorly for keeping the records of the patient. The patients would not be interacting with the system directly. The system needs to be user friendly and should be easy to learn. I was thinking to develop such a system using a CMS or an ERP or any other free tool. I have used wordpress/drupal in past but never used an ERP. Can you please guide me to make such a system using free, and preferably open source, tools? Update: I think it will be mostly a form driven system. What would be easy and better: creating the forms in drupal or using a php framework like symphony or cakePHP? Thanks, Akshey

  Read the article

• Unexpected media key behavior on new Acer Aspire

  - by Morgan May

  I'm having weird issues with the media keys (play/pause, previous, next, etc.) on a new Acer Aspire laptop. This is the first Acer I've owned and also my first Windows 7 computer, so I'm not sure whether the behavior is a result of some hidden Acer process that I haven't rooted out yet, or some Windows 7 option that I'm not aware of, or something else. I'm experiencing two issues that I suspect are related. Both problems are intermittent but happen more often than not. The media player I'm using is Winamp. I'm pretty sure I've had the same problem when using other media players, but when I tried to verify that before posting this, I only had the problems with Winamp. Because the problems are intermittent, I'm not sure if that's significant. 1) When I press the Play/Pause media key, in addition to playing or pausing the media player, it brings up a little menu in the center of the screen that lists my removable drives (CD/DVD, USB drives, etc.). To make the menu go away I have to either click away from it or hit Escape. Selecting a drive on the menu doesn't seem to do anything. 2) When I press the Previous or Next media keys, it skips 2+ tracks instead of just one (the exact number seems to vary). I've poked around all the control panel options that I can find, and looked through all the utilities that came with the computer with no luck. There's nothing that I can find in the (very slim) documentation, either. I have a hunch that the problem is caused by whatever utility manages global hotkeys, but I haven't found any way to configure that. Any guidance would be greatly appreciated. UPDATE: It looks like Winamp was the culprit. I did have the problem when using other media players, but when I uninstalled Winamp, the problem went away. I'd like to use Winamp, but I can survive with other players.

  Read the article

• How do I find the Serial Number of a USB Drive?

  - by jamuraa

  I'm trying to re-enable USB Autoplay in a secure way, by installing a program on each of the computers that I use so that I can run my launcher (PStart in this case) whenever I plug in my specific USB drive. The tool that I'm using to enable this - AutoRunGuard - needs the serial number of the USB drive that I am using. I can't figure out where to find this in Windows. Ideally I would not need to install and run a separate program to do this (seemingly) simple task. Since this is a pretty easy question, bonus points if you also tell me how to discover it in Linux as well. What steps do I need to take to retrieve a USB Drive's serial number? UPDATE: Just incase people come here looking for the answer for AutoRunGuard, I discovered that they don't want the USB device serial number, but the volume serial number. The drive serial can be found by going into the command line, navigating to the drive, and executing dir. The volume serial number is found in the top two lines - use it without the dash.

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Hi - Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message : "Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions? Many thanks Clem

  Read the article

• Dual boot Windows 8 and Ubuntu 12.10 across a reboot

  - by AK4749

  My Setup: I have two separate SSDs, and each contains an independently bootable OS - W8 and U12.10. From my extremely limited knowledge, this means each has a functioning EFI partition(?). My default boot order (GA-Z68XP-UD3P mobo with UEFI firmware update) boots the UEFI partition containing windows first, but if I enter the BIOS I can select the "ubuntu" entry to successfully boot ubuntu. Both drives are GPT, and are EFI boots. What I want to do: Reboot Windows 8, re-enter W8 (this is happening now due to the default boot order). What I want to change, however, is to boot into Ubuntu if i reboot from ubuntu. Essentially, I would like to work within one OS unless I consciously choose otherwise. Normally, I would not even ask to something I thought was impossible, but... Why I think this is possible: When trying EasyBCD to add ubuntu to the W8 UEFI bootloader, I noticed an "iReboot" addon or something that allows you to select which OS to boot into from within the OS. Note that I ended up not using the NeoGrub entry to chain Ubuntu off the W8 bootloader because I couldn't get much help with it. Is this possible? Have I had too much coffee and gone insane? Thank you all for your time, AK

  Read the article

• Dumping active directory

  - by Nop at NaDa

  I work in the IT support department of a branch of a huge company. I have to take care of a database with all the users, computers, etc. I'm trying to find a way to automatically update the database as much as possible, but the IT infrastructure guys doesn't give me enough privileges to use Active Directory in order to dump the users, nor they have the time to give me the information that I need. Some days ago I found Active Directory explorer from Sysinternals that allows me to browse through Active Directory, and I found all the information that I need there (username, real name, date when it was created, privileges, company, etc.). Unfortunately I'm unable to export the data to a human readable format. I'm just able to take a snapshot of the whole database in a machine-readable format. Doing the snapshot takes hours and I'm afraid that the infrastructure guys won't like me doing entire snapshots on a regular basis. Do you know of any tool (command-line is preferable) that would allow me to retrieve the values of the keys or export it to XML, CSV, etc?

  Read the article

• Made a .dmg for a project; user can't open it - "no mountable file systems"

  - by dragonridingsorceress

  Hello, We don't know a great deal about Macs. We had to make an installer, and were told to try a .dmg So we put together version 1, and it seemed to work. We had one application file, which had our icon, and one folder. The user was instructed to drag these into the Applications folder, of which there was the Mac version of a shortcut in the dmg. Then we were told we needed to update files, and assured that we could do so via drag-and-drop. So we did; we dragged them into the folder in the dmg. We tested it (on the computer we were using to edit the dmg) and it seemed to work. So we burnt it onto a disk (along with a windows installer that actually works!). I've just gotten an email from the recipient. She's got a Mac laptop. She inserted the disk, doubleclicked on it, doubleclicked on the .dmg, and got a Warning: no mountable file systems. Screenshot: http://www.flickr.com/photos/97292258@N00/5101670174/ I have the dmg (not on a disk) and am able to open it with no difficulty. How can we get it to work for our recipient?

  Read the article

• Excel controls not visible for certain users

  - by Nossidge

  One of the users of an Excel program I've written is having a weird problem. None of the control objects (Command Button, ComboBox, etc.) are visible to him when he opens the file on his laptop. He is using Excel 2003, the same version I used to create the program, and enables macros using the pop-up when the file loads. I have Googled this, and have found these people who seem to be having the exact same problem, with various versions of Excel. Unfortunately, none of their questions were answered. I can't really explain it any better than this user: If I enter design mode and pull a control from the control toolbar onto a sheet all I see are the drag handles. When not in design mode I have to feel around with the mouse and can click the button which executes the button click code correctly and opens another sheet where again I have to feel around for the buttons to return me to the original sheet. The button I managed to click is now visible but as soon as I click anywhere on the sheet it disappears. I have verified that the visible property of the buttons is set and that the Show All Objects on the Options View tab is selected. If I pull buttons from the Forms toolbar onto a sheet they are visible. If I try to find Objects using F5 when not in design mode Excel reports no objects on the sheet. So, Super Users, can you help? UPDATE: Thanks for your replies, but much like the person in the ozgrid link, the problem has gone away. Not sure why it went, but I can confirm that the user rebooted again and also started up other Excel files that didn't contain controls in the interim. Perhaps that fixed it, or maybe it'll be back again. I'll keep udating with progress, and close if the problem doesn't reoccur for the next few days. Thanks again.

  Read the article

• What causes this sonar sound on OS X?

  - by Richard Metzler

  Both of my Macs play this sonar sound that sounds like "ping ping ping ping" with a small amount of delay / echo. It occurs to me that it is played once a day but I'm not sure why. I checked iCal but didn't found anything (I don't use iCal anyways but maybe it's connected to Google calendar or my iPhone). I've heard this sound played by both my MacBook and my iMac but not yet simultaneously. Update This sound is not submarine.aiff. It sounds much more like what skub linked to but there are 4 "pings" instead of 1. It is played at different times (today around 5pm and again at 8.45, but as far as remember not everyday). That's why I'm not sure I could record it, but I could try. The sound might come from my iPhone, though I'm not sure which apps are alowed to play sound when they are not running. Also I don't see any indication in the message center or something similar. I think I have to start taking notes on which apps running.

  Read the article

• ATI Radeon 5670 Won't Show Resolutions over 1400x900

  - by Phil Sandler

  Just got my new Dell computer with Windows 7 and an ATI Radeon 5670. I attached it to my current monitor, which is a Samsung 24" (2443bwt). Windows 7 does not allow me to display in resolutions greater than 1400 x 900. The setup through a VGA cable into the VGA port of the card. The card also has a DVI port, but I need to use the VGA port because a KVM that supports VGA only. My old PC (which is Windows XP, GeForce 8600 video) can display in 1900 x 1200 on the same monitor (which is what I want) and even higher. It does this through a vga cable also connected to the KVM (through the DVI port but using an adapter). I have tried the same setup (DVI = VGA adapter) on the new PC and nothing changed. I have tried: Updating the drivers via Windows "Update Driver" (says they are current) Installing the updated version of the drivers from ATI (made no difference) Installing Powerstrip (all the options I would need for a custom resolution are greyed out) Installing the drivers/software from ATI caused the ATI Catalyst Control Center software to stop functioning, so I can no longer even start it. I have found some references to other people having this problem and instructions on cleaning the software off and reinstalling it (as uninstalling normally doesn't solve it). I will try this tonight. In any case, I didn't see any options in CCC that would allow me to override the settings for max resolution. However I didn't tinker with it too much before I tried updating the drivers, so I may have missed a setting. I contacted Samsung via online chat and they say it's a problem with the video card/driver (of course--what else would they say?). Any thoughts on what else I could try?

  Read the article

• Unwanted forced authentication after server restart (Win 2k3)

  - by Felthragar

  We're running a Win 2k3 R2 Standard 64-bit edition server. On this server we're running a fileserver and the ability to allow remote login to our network through vpn. We do not currently utilize a domain setup, all user accounts are local accounts on the server. Each employee is given a unique account to login to the server. The password is a randomly generated 16 character long string, which makes it hard to remember. What we've done is basicly had the password stored on the client machine (standard "Remember Me" functionality). This has worked well. However, last night our server automatically restarted after an automatic update. After that, some of our employees, myself included, had to re-authenticate with the server, submitting our credentials again. Then again, some others did not have to re-authenticate. Do you guys have any idea why this is? Is there a setting to prevent this? I've checked the logs but I couldn't find anything of interest. Then again I'm not really sure what I'm looking for. Thanks in advance, I'll try to answer any additional questions you may have. Edit: When I say "login" or "authenticate" I mean through the standard windows samba protocol. Edit 2: Ok, new day. Tonight the server restarted again, and the same two clients that had to re-authenticate yesterday had to re-authenticate today as well. The rest did not.

  Read the article

• How to set up a server without a hosting control panel

  - by A4J

  I have always used a control panel on my dedicated servers - from cPanel to Plesk to Virtualmin, and I am now considering ditching a CP altogether and manually editing config files. My requirements are fairly simple, I will host multiple sites on the server; some Apache with PHP & Mysql and some Passenger with Rails & Postgres. All will require email smtp/pop. FTP/Stats will not be required. Could someone please give me a quick run-down of what I would need to do - in terms of installing software and configuration? My server will come with a base install of CentOS 6.4 minimal. My thoughts so far: Install/update latest versions of MySQL & Postgres (are they 'safe' out of the box? Or do I need to do anything else like set up root passwords etc?) Install Apache & PHP (again, are the base installs good to go or do they require security tweaks?) Set up nameservers/hostnames/reverse DNS etc (Any guides on how to do this please?) Install Rubygems Install and configure Dovecot and Postfix (any tips on doing this? Or links to how-tos that cover it please?) Set up each website - any links to guides on how to do this? Install/configure firewall (or is the default install good to go?) Any other tips or advice would be greatly appreciated, as would links to guides or how-tos.

  Read the article

• Centralized backup method recommendation for SMEs with various OSes

  - by Akinator

  Hi I was wondering what in your opinion is the "best" method for having "everything" backed-up in the following situation. We are a SMEs with 10 computers in total. Three of those computers are MACs The rest are windows (1 vista, 4 win7 and 2 XPs) I'm very open to what the method should be but you should also consider the follwing: Very limited resources Quite "small" bandwidth (4 MBs for all (download) 0.4 MBs (upload, yep, thats it)- though this might get, a little bit better) One of the main thing to back up would be the mails, considerations: All windows computers use outlook, mainly 2003 There is one mac that uses outlook too (for mac of course - not 2011 yet) We also have to backup the files: Not a huge amount Very few very big files Very organizes (by machine) What I would like is to hear your opinions as to which would be the best method (or combination of methods - preferably one of course) considering. We are not sure what do we need and I'm open to suggestions, though an online (cloud based applications) would be great, remember the the bandwidth is unbearable. Last think to consider, it that we would like to do weekly updates (unless the method is very easy of course). Thanks in advance!! I tried to be as specific as possible, but if anything is needed I'll gladly update, please ask for any clarification needed! Please avoid any answers like upgrade all to windows 7 and throw away your macs :) our's may not be an ideal situation, but it is what it is, and right now, it would be impossible for us to change it for a lot of circumstances.

  Read the article

• can't install anything anymore with apt-get

  - by Aymane Shuichi

  Welcome this is the log I have when trying to install anything (php5-fpm after removing it) apt-get install php5-fpm Reading package lists... Done Building dependency tree Reading state information... Done php5-fpm is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up php5-fpm (5.4.4-14+deb7u10) ... insserv: warning: script 'S55IptabLes' missing LSB tags and overrides insserv: warning: script 'S55IptabLex' missing LSB tags and overrides insserv: There is a loop between service IptabLes and mountnfs if started insserv: loop involving service mountnfs at depth 8 insserv: loop involving service networking at depth 7 insserv: loop involving service mountnfs-bootclean at depth 10 insserv: There is a loop between service rc.local and mountall if started insserv: loop involving service mountall at depth 6 insserv: loop involving service checkfs at depth 5 insserv: loop involving service kbd at depth 11 insserv: There is a loop between service rc.local and mountall-bootclean if started insserv: loop involving service mountall-bootclean at depth 7 insserv: loop involving service urandom at depth 9 insserv: There is a loop between service IptabLes and mountdevsubfs if started insserv: loop involving service mountdevsubfs at depth 2 insserv: loop involving service udev at depth 1 insserv: There is a loop at service rc.local if started insserv: There is a loop at service IptabLes if started insserv: Starting IptabLes depends on rc.local and therefore on system facility `$all' which can not be true! (x99 times repeated ) insserv: Max recursions depth 99 reached insserv: loop involving service postfix at depth 2 insserv: There is a loop between service IptabLes and udev if started insserv: loop involving service mountkernfs at depth 1 insserv: loop involving service IptabLes at depth 1 Now here is the error i get insserv: exiting now without changing boot order! update-rc.d: error: insserv rejected the script header dpkg: error processing php5-fpm (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: php5-fpm E: Sub-process /usr/bin/dpkg returned an error code (1) The biggest operation I held before this was updating nginx from 1.2 to 1.6 and it was thanks to this site : here is the link : How to upgrade nginx from 1.2 to 1.6 on debian 7 Please help !

  Read the article

• Linksys SFE2000 Interface

  - by boburob

  I have a real problem with a layer 3 Linksys switch. First, every time it looses power, it seems to reset back to an older config. Not only this, but when this happens it looses interface settings on one subnet. This would not be a problem but I am completely unable to get to the interface on the working side. It allows me to log on and then just displays a blank screen. I have tried this on: IE6 IE7 IE8 IE9 Firefox 3.5 Opera Chrome All with the same results, except for Opera, which loads half the interface but nothing I can really use. I really need to get onto this switch so I can sort out routing and VLAN tagged ports, so if anyone has any ideas on either of these issues please let me know ASAP! Thanks! Also, due to its location and my lack of laptops with serial connections I cannot putty into it. UPDATE: Looked into this a bit more and it looks like this model of switch does not save the current config to boot unless you make sure to save it yourself, which explains the first issue, however the broken interface is more worrying!

  Read the article

• Windows Server 2008 R2 creating a multi-year client certificate using the IIS certsrv page while deploying SSTP VPN

  - by Warren P

  I am trying to follow instructions on Technet about deploying a Standard (non-enterprise) SSTP based VPN) that were originally written for Server 2008, but I am using Server 2008 R2, I have gotten as far as the part where it asks you to create a request a Server Authentication certificate. I have deployed IIS, and Active Directory Certificate Services, and chose "Standalone" and "Standard" (non-enterprise) Certificate Authority because I don't have an OID and don't think I should have to get one for a simple deployment of SSTP. The resulting certificates made by the Certification Authority "Issue" command, only have a 1 year period of validity, I want a multi-year certificate. At no point in this process is there any way to input this information unless it's through the Attributes text input area on the Advance Certificate Request page, which appears to be generated using an old ActiveX control, which means I can only do this using the workarounds in the article that I linked at the top, and only using Internet Explorer. Update:: It may be that this question is pointless since self-signed keys do not appear to work, when I try them, using Windows 8 as the VPN client. The problem is that the keys that are self-created by the technique shown here do not have any Certificate Revocation Server URLs and so you get an error "The revocation function was unable to check revocation", and the VPN connection fails.

  Read the article

< Previous Page | 812 813 814 815 816 817 818 819 820 821 822 823  | Next Page >