Search Results

Search found 28784 results on 1152 pages for 'start'.

Page 852/1152 | < Previous Page | 848 849 850 851 852 853 854 855 856 857 858 859  | Next Page >

• File transfer problems through VPN when Cisco IPS is enabled

  - by Richard West

  We have a Cisco ASA 5510 firewall with the IPS module installed. We have a customer that we must connect to via VPN to their network to exchange files via FTP. We use the Cisco VPN client (version 5.0.01.0600) on our local workstations, which are behind the firewall and subject to the IPS. The VPN client is successful in connecting to the remote site. However when we start the FTP file transfer we are able to upload only 150K to 200K of data, then everything stops. A minute later the VPN session is dropped. I think I have isolated this to an IPS issue by temporarily disabling the Service Policy on the ASA for the IPS with the following command: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 inactive After this command was issued I then established the VPN to the remote site and was successful in transferring the entire file. While still connected to the VPN and FTP session I issued the command to enable the IPS: access-list IPS line 1 extended permit ip 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 The file transfer was tried again and was once again successful so I closed the FTP session and reopened it, while keeping the same VPN session open. This file transfer was also successful. This told me that nothing with the FTP programs was being filtered or causing the problem. Furthermore, we use FTP to exchange files with many sites everyday without issue. I then disconnected the original VPN session, which was established when the access-list was inactive, and reconnected the VPN session, now with the access-list active. After starting the FTP transfer the file stopped after 150K. To me this seems like the IPS is blocking, or somehow interfering with the initial VPN setup to the remote site. This only started happening last week after the latest IPS signature updates were applied (sig version 407.0). Our previous sig version was 95 days old becuase the system was not auto updating itself. Any ideas on what could be causing this problem?

  Read the article

• Web based KVM management for Ubuntu

  - by Tim

  Hey all, We've got a single Ubuntu 9.10 root server on which we want to run multiple KVM virtual machines. To administer these virtual machines I'd like a web based KVM management tool, but I don't know which one to choose from the list of tools mentioned on linux-kvm.org. I've used virsh & virt-manager on my desktop, but would like a web interface for the server. I tested ConVirt on my desktop, but it failed to pickup KVM machines from virsh / virt-manager, and I could not get KVM virtual machine import to work (only Xen). oVirt looks good, but I can't find out if and how I can install it on Ubuntu 9.10.. (And I'd really rather not waste another few days on testing stuff that might not work in the end.) Can anyone recommend any good web based KVM management tools that are easy to install on Ubuntu 9.10? I'm looking for something that will also allow me to run other services like apache and postgresql besides hosting virtual machines, so preferably fairly lightweight & no dedicated OS installs. We don't need any professional clustering / migration or anything, just something that will let us create, start, inspect, administer & stop virtual machines from a web page. Best regards, Tim

  Read the article

• apache2 VirtualHost in Mac OS X home directory

  - by aaron

  I am running Macports apache2 on Mac OS X 10.5. Whenever I configure a virtual host in the default folder, it works, however when I configure the virtual host in my home directory I get a "403 Forbidden" error. How do I configure a vhost in my home directory? Here is the configuration that yields "403 Forbidden" when I access "devel.mysite.com": /opt/local/apache2/conf/extra/httpd-vhosts.conf: DocumentRoot "/opt/local/apache2/htdocs" ServerName * #CustomLog "" common <VirtualHost *:80> #DocumentRoot "/opt/local/apache2/htdocs/mysite" DocumentRoot "/Users/myuser/Sites/mysite" ServerName devel.mysite.com </VirtualHost> The error message in /opt/local/apache2/logs/devel.mysite.com-error_log: [Sat Apr 17 19:54:49 2010] [error] [client 127.0.0.1] client denied by server configuration: /Users/myuser/Sites/mysite/ When I uncomment the line to make DocumentRoot in /opt/local/apache2/htdocs/mysite, it works: DocumentRoot "/opt/local/apache2/htdocs" ServerName * #CustomLog "" common <VirtualHost *:80> DocumentRoot "/opt/local/apache2/htdocs/mysite" #DocumentRoot "/Users/myuser/Sites" ServerName devel.mysite.com </VirtualHost> I get no errors or warnings when I start apache, and the only thing that is logged on startup is this (in /opt/local/apache/logs/error_log): [Sat Apr 17 19:56:29 2010] [notice] Digest: generating secret for digest authentication ... [Sat Apr 17 19:56:29 2010] [notice] Digest: done [Sat Apr 17 19:56:29 2010] [notice] Apache/2.2.14 (Unix) mod_ssl/2.2.14 OpenSSL/0.9.8m DAV/2 configured -- resuming normal operations A few notes: * The permissions of /Home/myuser/Sites/mysite is 755, owned by myuser, group is staff * Everything else works as expected, until I move the ServerRoot of the vhost to the directory in my home

  Read the article

• Powerpoint 2010 crash on quickstyle menu

  - by Marcus Lindblom

  Windows 7 64-bit, recent install, added Office 2010. When I create some boxes and open the quick-style menu, it crashes (or stops responding, in windowese, and then it sends an error report). I've run the "Repair" from the installer, but it didn't help. There's nothing in Windows Update I've Googled and searched on Microsoft's site, but n Any other ideas? (It's not related to this ppt crash question as that concerns PPT 2007. Error in event log: Faulting application name: POWERPNT.EXE, version: 14.0.4754.1000, time stamp: 0x4b967cf2 Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdfe0 Exception code: 0xe0000003 Fault offset: 0x000000000000aa7d Faulting process id: 0xee8 Faulting application start time: 0x01cb9dc710fd76d8 Faulting application path: C:\Program Files\Microsoft Office\Office14\POWERPNT.EXE Faulting module path: C:\Windows\system32\KERNELBASE.dll Report Id: 58766562-09ba-11e0-90d1-00215a139192 And: Fault bucket , type 0 Event Name: APPCRASH Response: Not available Cab Id: 0 Problem signature: P1: POWERPNT.EXE P2: 14.0.4754.1000 P3: 4b967cf2 P4: KERNELBASE.dll P5: 6.1.7600.16385 P6: 4a5bdfe0 P7: e0000003 P8: 000000000000aa7d P9: P10: Attached files: C:\Users\marcusl\AppData\Local\Temp\CVR86DD.tmp.cvr C:\Users\marcusl\AppData\Local\Temp\WERC765.tmp.WERInternalMetadata.xml These files may be available here: C:\Users\marcusl\AppData\Local\Microsoft\Windows\WER\ReportArchive\AppCrash_POWERPNT.EXE_d45f313d77f7e52cc8682b2b64cc3898127c2c_1106e3ac Analysis symbol: Rechecking for solution: 0 Report Id: 58766562-09ba-11e0-90d1-00215a139192 Report Status: 1

  Read the article

• Route specific HTTP requests through pfSense OpenVPN

  - by DennisQ

  Hi, to start, I have very little knowledge on routes, iptables, etc. That said, here's what I'm trying to accomplish and where I think I'm stumped: Problem: We have an external website which we recently firewalled so it only accepts traffic from our office IP addresses. This works well at the office, but doesn't work for remote access through VPN as we don't route all traffic through OpenVPN. I would rather avoid forcing everyone to route all traffic through just to accommodate this one site. Environment: Main router box is running pfSense. Em0 is internal IP, Em1 is external. Internal net is 10.23.x and VPN is 10.0.8.0/24 I believe what I need to do is add a route to the VPN server config to send all traffic to that IP over the VPN tunnel. I think that part's working, but I don't get a response back, so I'm assuming that I need some NAT config on the VPN server to route the response back over the tunnel? What I've found so far is to try the following, but since this is a pfSense box on FreeBSD, I can't run iptables, etc. Make sure ip forwarding is enabled: echo 1 /proc/sys/net/ipv4/ip_forward Setup NAT back out: iptables -t nat -A POSTROUTING -s 10.0.8.0/24 -o em0 -j MASQUERADE Am I on the right path, and if so how do I accomplish this through pfSense UI or FreeBSD CLI? Thanks!

  Read the article

• Webmin / Virtualmin running php as www-data, is locked out of viewing .htaccess and writing

  - by Kirill

  I've asked this on the virtualmin forums, but haven't had any help from there. Recently, "something" happened and it seems that the apache service has gone a bit weird. What it does: it runs all apache traffic as www-data and sometimes spawns the php5-cgi process as www-data, this is a problem because all the domain users own their directories and default permissions don't let www-data write to these folders (file uploads are dead) or read .htaccess (permalinks are broken in wordpress). I've googled this for about a week straight now, tried pretty much everything I could find and achieved nothing. The only thing that I think might actually be the cause of all this is this page: http:// - i.imgur.com/NYW3x.png (got shut down by the spam filter) So I figured if I set it to "default", this might magically start working again, but all it does is "crash" apache (all websites timeout). I figure it's something to do with the "mpm" module or something, but I can't find anything relevant in the settings to modify for it to work. Can someone please point me in the right direction? System info: Webmin version 1.580 Kernel and CPU Linux 2.6.35.4-rscloud on x86_64 Virtualmin version 3.90.gpl GPL Ubuntu 10.04 LTS (Lucid) A couple screenshots of top http://i.imgur.com/U2DTK.png http://i.imgur.com/sNPKs.png

  Read the article

• Unconvert Text File from Binary Format

  - by Hammer Bro.

  I've got a rather large CSV file (~700MB) which I know to consist of lines of 27-character alpha-numeric hashes; no commas or anything fancy. Somehow, during its migration from Windows to Linux (via winSCP and then a few regular SCPs), it has converted into some kind of binary format I am unfamiliar with. If I open the file in vi, everything appears fine, and it says [converted] at the bottom, although I know it's not a line endings issue (and dos2unix doesn't help). If I 'head' the file, it looks proper except for a "ÿþ" at the beginning of the first line. If I open up the file in nano, however, I see the "ÿþ" at the start and then "^@" before every character (even newlines and EoF). If I try to re-save or copy the file (say via: head file.csv short.txt), this special encoding is preserved. I copied the first ten lines out of vi (which displays it properly) into my Windows clipboard via my SSH client, then pasted it into a new text file, test.txt. This file is visually identical when opened in vi (and similar through 'head', minus the "ÿþ"), although it's roughly half of the filesize. Additionally, file test.txt test.txt: ASCII text file short.txt short.txt: I have no idea what format this once-text file got converted to (it's notoriously hard to search the internet for symbols), but surely there must be some way to convert it back. Any ideas?

  Read the article

• sftpd: No available certificate or key corresponds to the SSL cipher suites which are enabled?

  - by Arcturus

  Hello. I'm trying to setup vsftpd on Fedora 12. I need to require use of FTPS, and for now need to use a self-signed SSL certificate. I managed to get the vsftpd service running and to connect as my user. I can list the home directory, but as soon as I try to list another directory, download or upload a file, I get this error: No available certificate or key corresponds to the SSL cipher suites which are enabled. And the xfer log is empty. I've been Googling it for a while now, but still can't understand the problem. Here's how I installed vsftpd: su yum install vsftpd chkconfig vsftpd on service vsftpd start I tried to generate the certificate in two ways. Here's the first one: cd /etc/vsftpd openssl req -x509 -nodes -days 365 -newkey rsa:1024 -keyout vsftpd.pem -out vsftpd.pem Here's the second way: cd /etc/pki/tls/certs make vsftpd.pem Here's my vsftpd configuration: anonymous_enable=NO local_enable=YES write_enable=YES local_umask=022 dirmessage_enable=YES xferlog_enable=YES connect_from_port_20=YES xferlog_file=/var/log/vsftpd.log xferlog_std_format=YES nopriv_user=ftpsecure chroot_local_user=YES chroot_list_enable=YES chroot_list_file=/etc/vsftpd/chroot_list listen=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES # SSL settings ssl_enable=YES force_local_data_ssl=YES force_local_logins_ssl=YES rsa_cert_file=/etc/pki/tls/certs/vsftpd.pem allow_anon_ssl=NO ssl_tlsv1=YES ssl_sslv2=NO ssl_sslv3=NO Does anyone know what the problem is and how to solve it?

  Read the article

• How to boot Linux from a 16gb USB flash drive

  - by Chris Harris

  I'm trying to install Linux on a single partition of a USB flash drive that's larger than 4gb. The first place I went to is http://pendrivelinux.com. I can follow these instructions for installing Xubuntu 9.04 perfectly, which unfortunately break down when I try to scale it up beyond 4gb. There are several other tools to do this (unetbootin and usb-creator) which follow a very similar formula. I figured out that a big problem of mine was that all of these tools assume the USB drive is formatted in FAT32, which unfortunately cannot hold a single file larger than 4gb. This is unfortunate because I want to use just one partition, so that my persistance file, casper-rw, looks like one big partition to the OS once I've booted off of the USB drive. I then tried following a myriad of instructions involving formatting the drive as one large ext2 filesystem and using extlinux to create a single bootable ext2 file system. This doesn't work for me however, after about 20 attempts verifying and slightly tweaking the formula, I cannot seem to get a "good" bootable ext2 file system built. I'm not entirely sure what's going on, but it seems as though no matter how hard I try, I cannot get the ext2 file system to remain coherent after copying the Linux ISO contents over, copying the MBR, and executing extlinux to create the ext bootloader. Every time, after I follow these steps (in any order) and reboot, I get an unbootable USB drive. If I then mount the drive under Linux again, I see a mess of a file system (inodes have clearly been screwed up somewhere along the way). I suspected that the USB drive wasn't being fully flushed, so I tried using the "sync" and "unmount" commands before rebooting which didn't affect things at all. I guess I have several possible questions - but let's start with the obvious - is there something I'm missing to create a bootable ext2 USB flash drive that's large (e.g. 16gb)?

  Read the article

• Side-By-Side Configuration Error VC90.CRT

  - by Swiss

  I keep receiving the following error when trying to run MikTeX 2.8 or Visual Studio 2008 on 64-Bit Windows Vista. It's particularly odd because both programs were working problem free until a few days ago. The application has failed to start because its side-by-side configuration is incorrect. Please see the application event log for more detail. Opening the Application log provides the following information: Activation context generation failed for "C:\Program Files (x86)\MiKTeX 2.8\miktex\bin\texworks.exe". Error in manifest or policy file "C:\Program Files (x86)\MiKTeX 2.8\miktex\bin\Microsoft.VC90.CRT.MANIFEST" on line 4. Component identity found in manifest does not match the identity of the component requested. Reference is Microsoft.VC90.CRT,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="9.0.30729.4148". Definition is Microsoft.VC90.CRT,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="9.0.30729.1". Please use sxstrace.exe for detailed diagnosis. It looks like the problem is with Microsoft.VC90.CRT.MANIFEST, but I am not sure why or how to fix this problem. I have tried uninstalling/reinstalling Visual Studio and MikTeX, as well as uninstalling/reinstalling Microsoft's C++ Redistributable, but nothing seems to be fixing this problem.

  Read the article

• Overheating computer

  - by Samurai Waffle

  My computer overheats somewhat frequently, usually during intense use. And by intense use I mean browsing the internet while downloading, or gaming. It even overheats on extremely old games though, Master of Orion 2, which was developed for Windows 95. My computer has a Pentium 4 Ghz processor, 2 GB of ram, and is running Windows XP. One of the symptoms it has after overheating, is that it'll turn on immediately afterwards, but won't show any video on my monitor. I usually have to wait at least 5 minutes (mostly at least 10) before I can get it to turn on and show video on my monitor. I also usually have to wiggle around the graphics card a little bit, which is the ASUS A9550 Series with 256 MB. I'm not sure exactly what is causing the computer to overheat. At first I thought it was the video card, but after I noticed it was doing it while playing Master of Orion 2, I'm not so sure, because that game can't be making the video card work all that hard. So how exactly can I pinpoint the problem? Thanks for any help provided. Edit: Okay I downloaded the programs that you specified, and will start benchmarking my system to try and pinpoint what's overheating. What is the temperature range for when it's getting to hot? Also I have an abundant amount of software experience with computers, but unfortunately not to much hardware experience.

  Read the article

• Dual NVidia graphics cards in Ubuntu / xorg.conf mania

  - by John Zwinck

  I have two NVidia graphics cards: Quadro NVS 295 (PCI Express, dual DisplayPort outputs) GeForce FX 5200 (PCI, DVI and VGA outputs) I have three identical monitors, two on DisplayPort and one on DVI. I'm on Ubuntu Hardy (and cannot currently dist-upgrade for separate reasons). I use the "nvidia" driver. What's new is the GeForce card and the third monitor. I currently have the dual DisplayPort monitors working fine. Here are the display-related parts of my xorg.conf: Section "ServerLayout" Identifier "Default Layout" Screen "PCI-Express Screen" 0 0 # adding this makes X fail to start: Screen "PCI Screen" 0 Inputdevice "Generic Keyboard" Inputdevice "Configured Mouse" EndSection Section "Module" Load "glx" # not sure why/if this is needed EndSection Section "Monitor" Identifier "DELL 2408WFP" Option "DPMS" EndSection Section "Device" Identifier "NVIDIA Quadro NVS 295" Driver "nvidia" Option "RenderAccel" "true" Screen 0 BusID "PCI:2:0:0" EndSection Section "Device" Identifier "NVIDIA GeForce FX 5200" Driver "nvidia" Option "RenderAccel" "true" Screen 1 BusID "PCI:6:4:0" EndSection Section "Screen" Identifier "PCI-Express Screen" Device "NVIDIA Quadro NVS 295" Monitor "DELL 2408WFP" Defaultdepth 24 Option "TwinView" "True" Option "UseEdidFreqs" "True" Option "MetaModes" "1920x1200 +0+1200, 1920x1200 +0+0" EndSection Section "Screen" Identifier "PCI Screen" Device "NVIDIA GeForce FX 5200" Monitor "DELL 2408WFP" Defaultdepth 24 Option "TwinView" "True" Option "UseEdidFreqs" "True" Option "MetaModes" "1920x1200 +0+0" EndSection I use nvidia-settings to configure my monitors, and it does not show the second GPU. lspci, though, shows: 02:00.0 VGA compatible controller: nVidia Corporation Unknown device 06fd 06:04.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] Which is where I got the BusID settings for the two devices (when I just had one device, I didn't have any BusID listed...and adding the BusID hasn't broken anything). What am I missing? How can I make nvidia-settings show my second GPU so I can then configure its monitor?

  Read the article

• How to repair multiple KDC an Netlogon errors

  - by Keith Sirmons

  Howdy, I have several erros in the system event log of my single Windows 2003 SP2 domain controller. Multiple member computers on the domain are listed in these errors. I am seeing two similar errors for each computer one second apart in the event log. Event ID 7 Source KDC The Security Account Manager failed a KDC request in an unexpected way. The error is in the data field. The account name was [email protected] and lookup type 0x8. followed by Event ID 7 Source KDC The Security Account Manager failed a KDC request in an unexpected way. The error is in the data field. The account name was MEMBERNAME$ and lookup type 0x8. The Lookup Types are also different, I have 0x8, 0x28, 0x0, 0x20. I am also receiving other authentication errors in the same time frame as all of the KDC errors Event ID 5722 Source NETLOGON The session setup from the computer MEMBERNAME failed to authenticate. The name(s) of the account(s) referenced in the security database is MEMBERNAME$. The following error occurred: Access is denied. I have run dcdiag /v to see if there was something wrong with Active Directory, but all tests passed. I also ran netdiag /v and it appers all of those tests ran. Any ideas on where to start for this issue? Thank you, Keith

  Read the article

• How can I install Satchmo?

  - by Jonathan Hayward

  I am trying to install Satchmo 0.9 on an Ubuntu 9.10 guest off of the instructions at http://bitbucket.org/chris1610/satchmo/downloads/Satchmo.pdf. I run into difficulties at 2.1.2: pip install -r http://bitbucket.org/chris1610/satchmo/raw/tip/scripts/requirements.txt pip install -e hg+http://bitbucket.org/chris1610/satchmo/@v0.9#egg=satchmo The first command fails because a compile error for how it's trying to build PIL. So I ran an "aptitude install python-imaging", locally copy the first line's requirements.text, and remove the line that's unsuccessfully trying to build PIL. The first line completes without error, as does the second. The next step tells me to change directory to the /path/to/new/store, and run: python clonesatchmo.py A little bit of trouble here; I am told that clonesatchmo.py will be in /bin by now, and it isn't there, but I put some Satchmo stuff under /usr/local, create a symlink in /bin, and run: python /bin/clonesatchmo.py This gives: jonathan@ubuntu:~/store$ python /bin/clonesatchmo.py Creating the Satchmo Application Traceback (most recent call last): File "/bin/clonesatchmo.py", line 108, in <module> create_satchmo_site(opts.site_name) File "/bin/clonesatchmo.py", line 47, in create_satchmo_site import satchmo_skeleton ImportError: No module named satchmo_skeleton A find after apparently checking out the repository reveals that there is no file with a name like satchmo*skeleton* on my system. I thought that bash might be prone to take part of the second pip invocation's URL as the beginning of a comment; I tried both: pip install -e hg+http://bitbucket.org/chris1610/satchmo/@v0.9\#egg=satchmo pip install -e hg+http://bitbucket.org/chris1610/satchmo/@v0.9#egg=satchmo Neither way of doing it seems to take care of the import error mentioned above. How can I get a Satchmo installation under Ubuntu, or at least enough of a Satchmo installation that I am able to start with a skeleton of a store and then flesh it out the way I want? Thanks, Jonathan

  Read the article

• Apache Config: RSA server certificate CommonName (CN) ... NOT match server name!?

  - by mmattax

  I'm getting this in error_log when I start Apache: [Tue Mar 09 14:57:02 2010] [notice] mod_python: Creating 4 session mutexes based on 300 max processes and 0 max threads. [Tue Mar 09 14:57:02 2010] [warn] RSA server certificate CommonName (CN) `*.foo.com' does NOT match server name!? [Tue Mar 09 14:57:02 2010] [warn] RSA server certificate CommonName (CN) `www.bar.com' does NOT match server name!? [Tue Mar 09 14:57:02 2010] [notice] Apache configured -- resuming normal operations Child processes then seem to seg fault: [Tue Mar 09 14:57:32 2010] [notice] child pid 3425 exit signal Segmentation fault (11) [Tue Mar 09 14:57:35 2010] [notice] child pid 3433 exit signal Segmentation fault (11) [Tue Mar 09 14:57:36 2010] [notice] child pid 3437 exit signal Segmentation fault (11) Server is RHEL, what's going on and what do I need to do to fix this? EDIT As requested, the dump from httpd -M: Loaded Modules: core_module (static) mpm_prefork_module (static) http_module (static) so_module (static) auth_basic_module (shared) auth_digest_module (shared) authn_file_module (shared) authn_alias_module (shared) authn_anon_module (shared) authn_default_module (shared) authz_host_module (shared) authz_user_module (shared) authz_owner_module (shared) authz_groupfile_module (shared) authz_default_module (shared) include_module (shared) log_config_module (shared) logio_module (shared) env_module (shared) ext_filter_module (shared) mime_magic_module (shared) expires_module (shared) deflate_module (shared) headers_module (shared) usertrack_module (shared) setenvif_module (shared) mime_module (shared) status_module (shared) autoindex_module (shared) info_module (shared) vhost_alias_module (shared) negotiation_module (shared) dir_module (shared) actions_module (shared) speling_module (shared) userdir_module (shared) alias_module (shared) rewrite_module (shared) cache_module (shared) disk_cache_module (shared) file_cache_module (shared) mem_cache_module (shared) cgi_module (shared) perl_module (shared) php5_module (shared) python_module (shared) ssl_module (shared) Syntax OK

  Read the article

• SharePoint 2010 User Profile Synchronization

  - by manemawanna

  Hello, I'm completely new to working with SharePoint and Windows Server, but last week I was given a small brief to play with SharePoint 2010 to see how I got along with it. Anyway I've set up a SharePoint server and had a mess around to get some new sites and pages created etc, but I'm now looking to have a try at importing some AD groups. As part of this I've look at these tutorials, here and here. So far I've got through to the process of starting the User Profile Service which works fine, but when I get it starting the User Profile Synchronization service it sits on starting. But when I refresh the page or go to the monitoring section it shows it as aborted. Now I'm new to administering servers like I say and when I start the User Profile Synchronization service it tries to run as NT AUTHORITY\NETWORK SERVICE and asks for a password so I've been providing it with the admin password, now I'm not sure if this is part of the issue or not as I've checked the log files and they seem to say that it doesn't have permissions, which is fair enough, but I can't see how you can change the account even if I wanted to. So if anyone could help it would be appreciated, if you need any further information to help with an answer, just let me know.

  Read the article

• X11 performance problem after upgrading from Centos3 to Centos5 with an ATI Rage XL

  - by Marcelo Santos

  After upgrading a computer from Centos3 to Centos5 an application that does a lot of scrolling took a very high performance hit. top tells me that X is using a lot of CPU and that was not happening before. The machine has an ATI Rage XL with 8MB and X is using the ati driver as there is no proprietary ATI driver for this board on linux. The xorg.conf: Section "Device" Identifier "Videocard0" Driver "ati" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Group 0 Mode 0666 EndSection A similar machine that still has Centos3 installed is able to start DRI on the X server while this one is not, this is the Xorg.0.log for the Centos5 machine: drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed [drm] failed to load kernel module "mach64" (II) ATI(0): [drm] drmOpen failed (EE) ATI(0): [dri] DRIScreenInit Failed (II) ATI(0): Largest offscreen areas (with overlaps): (II) ATI(0): 1024 x 1279 rectangle at 0,768 (II) ATI(0): 768 x 1280 rectangle at 0,768 (II) ATI(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Lines Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 10 256x256 slots (==) ATI(0): Backing store disabled (==) ATI(0): Silken mouse enabled (II) ATI(0): Direct rendering disabled (==) RandR enabled I also tried using EXA instead of XAA and setting: Option "AccelMethod" "XAA" Option "XAANoOffscreenPixmaps" "true" uname -a Linux sir5.erg.inpe.br 2.6.18-128.7.1.el5 #1 SMP Mon Aug 24 08:20:55 EDT 2009 i686 i686 i386 GNU/Linux rpm -qa | grep xorg-x11-server xorg-x11-server-utils-7.1-4.fc6 xorg-x11-server-sdk-1.1.1-48.52.el5 xorg-x11-server-Xvfb-1.1.1-48.52.el5 xorg-x11-server-Xnest-1.1.1-48.52.el5 xorg-x11-server-Xorg-1.1.1-48.52.el5 The drmOpenDevice error continues when using the suggested Option "AIGLX" "true".

  Read the article

• Configuration management in support of scientific computing

  - by Sharpie

  For the past few years I have been involved with developing and maintaining a system for forecasting near-shore waves. Our team has just received a significant grant for further development and as a result we are taking the opportunity to refactor many components of the old system. We will also be receiving a new server to run the model and so I am taking this opportunity to consider how we set up the system. Basically, the steps that need to happen are: Some standard packages and libraries such as compilers and databases need to be downloaded and installed. Some custom scientific models need to be downloaded and compiled from source as they are not commonly provided as packages. New users need to be created to manage the databases and run the models. A suite of scripts that manage model-database interaction needs to be checked out from source code control and installed. Crontabs need to be set up to run the scripts at regular intervals in order to generate forecasts. I have been pondering applying tools such as Puppet, Capistrano or Fabric to automate the above steps. It seems perfectly possible to implement most of the above functionality except there are a couple usage cases that I am wondering about: During my preliminary research, I have found few examples and little discussion on how to use these systems to abstract and automate the process of building custom components from source. We may have to deploy on machines that are isolated from the Internet- i.e. all configuration and set up files will have to come in on a USB key that can be inserted into a terminal that can connect to the server that will run the models. I see this as an opportunity to learn a new tool that will help me automate my workflow, but I am unsure which tool I should start with. If any member of the community could suggest a tool that would support the above workflow and the issues specific to scientific computing, I would be very grateful. Our production server will be running Linux, but support for OS X would be a bonus as it would allow the development team to setup test installations outside of VirtualBox.

  Read the article

• Configuration management in support of scientific computing

  - by Sharpie

  For the past few years I have been involved with developing and maintaining a system for forecasting near-shore waves. Our team has just received a significant grant for further development and as a result we are taking the opportunity to refactor many components of the old system. We will also be receiving a new server to run the model and so I am taking this opportunity to consider how we set up the system. Basically, the steps that need to happen are: Some standard packages and libraries such as compilers and databases need to be downloaded and installed. Some custom scientific models need to be downloaded and compiled from source as they are not commonly provided as packages. New users need to be created to manage the databases and run the models. A suite of scripts that manage model-database interaction needs to be checked out from source code control and installed. Crontabs need to be set up to run the scripts at regular intervals in order to generate forecasts. I have been pondering applying tools such as Puppet, Capistrano or Fabric to automate the above steps. It seems perfectly possible to implement most of the above functionality except there are a couple usage cases that I am wondering about: During my preliminary research, I have found few examples and little discussion on how to use these systems to abstract and automate the process of building custom components from source. We may have to deploy on machines that are isolated from the Internet- i.e. all configuration and set up files will have to come in on a USB key that can be inserted into a terminal that can connect to the server that will run the models. I see this as an opportunity to learn a new tool that will help me automate my workflow, but I am unsure which tool I should start with. If any member of the community could suggest a tool that would support the above workflow and the issues specific to scientific computing, I would be very grateful. Our production server will be running Linux, but support for OS X would be a bonus as it would allow the development team to setup test installations outside of VirtualBox.

  Read the article

• Why can’t two programs access my webcam simultaneously?

  - by qdii

  I first launch cheese and my webcam turns on. I then run vlc to grab the output of /dev/video0 but it fails with: [0x7f3ea40012e8] v4l2 demux error: cannot set input 0: Device or resource busy [0x7f3ea40012e8] v4l2 demux error: cannot set input 0: Device or resource busy [0x7f3ea4002168] v4l2 access error: cannot set input 0: Device or resource busy [0x7f3ea4002168] v4l2 access error: cannot set input 0: Device or resource busy [0x7f3eb4000b78] main input error: open of `v4l2:///dev/video0' failed Whatever pair of video programs I run (skype, cheese, vlc, etc.), the result is always the same: the second program can no longer use the webcam when the first one has already grabbed the output. However I find it curious as video4linux states: In general, V4L2 devices can be opened more than once. When this is supported by the driver, users can for example start a "panel" application to change controls like brightness or audio volume, while another application captures video and audio. My webcam is seen in lspci as 058f:a014 Alcor Micro Corp. Asus Integrated Webcam, but I don’t even know what the underlying driver is, so I can’t check whether my problem is driver-related or not. Any input would be more than welcome!

  Read the article

• Why are my Windows 7 updates continuously failing?

  - by Chris C.

  I'm an advanced level user here with an odd issue. I have two Windows Updates that are failing to install, every single time. I'm getting a mysterious "Code 1" error on both updates, an error for which I'm having difficulty finding a solution. The updates in question are: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Because these updates are failing, the Shut Down button in my start menu always has the shield icon next to it, indicating that "new" updates will be installed on shut down. But, of course, they'll fail and when the PC is restarted, the shield icon is still there. When checking the update history and viewing the details of the failed updates, I get the following: Security Update for Microsoft Visual C++ 2008 Service Pack 1 Redistributable Package (KB2538243) Installation date: ?6/?29/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important A security issue has been identified leading to MFC application vulnerability in DLL planting due to MFC not specifying the full path to system/localization DLLs. You can protect your computer by installing this update from Microsoft. After you install this item, you may have to restart your computer. More information: http://go.microsoft.com/fwlink/?LinkId=216803 System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [May 2011] Installation date: ?6/?28/?2011 3:00 AM Installation status: Failed Error details: Code 1 Update type: Important This tool is being offered because an inconsistency was found in the Windows servicing store which may prevent the successful installation of future updates, service packs, and software. This tool checks your computer for such inconsistencies and tries to resolve issues if found. More information: http://support.microsoft.com/kb/947821 About My System I'm running Windows 7 Home Premium x64 Edition. This is a custom PC build and the OS was installed fresh, not an upgrade from a previous version. I've been running this system for about 4 months. Windows Updates aside, the system is usually quite stable. Thanks in advance for your help!

  Read the article

• Vista logs into black screen, "Application Error 0xc0000022" for explorer.exe

  - by IMAPC

  Whenever I attempt to log into a Windows Vista computer (the only account on it), I'm presented with a black screen & a cursor. I can open Task Manager, and from there I can launch applications. It seems to be using Aero Basic (instead of the full Aero which I had set as default before the problem started). When attempting to launch "explorer.exe" I get "explorer.exe - Application Error 'The application failed to initialize properly (0xc0000022). Click OK to terminate the application.'" Every now and then I get an error along the lines of "the application has failed to start because its side by side configuration is incorrect please see the application event log for more detail." I can boot into safe mode successfully, but I still get the black screen when I log into it in regular mode. I've tried most of the suggestions here, but did not work. I'm attempting to back up everything right now in case the only fix is to reinstall Windows. Has anyone seen this before?

  Read the article

• Cisco 891w multiple VLAN configuration

  - by Jessica

  I'm having trouble getting my guest network up. I have VLAN 1 that contains all our network resources (servers, desktops, printers, etc). I have the wireless configured to use VLAN1 but authenticate with wpa2 enterprise. The guest network I just wanted to be open or configured with a simple WPA2 personal password on it's own VLAN2. I've looked at tons of documentation and it should be working but I can't even authenticate on the guest network! I've posted this on cisco's support forum a week ago but no one has really responded. I could really use some help. So if anyone could take a look at the configurations I posted and steer me in the right direction I would be extremely grateful. Thank you! version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESI ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings ! aaa new-model ! ! aaa authentication login userauthen local aaa authorization network groupauthor local ! ! ! ! ! aaa session-id common ! ! ! clock timezone EST -5 clock summer-time EDT recurring service-module wlan-ap 0 bootimage autonomous ! crypto pki trustpoint TP-self-signed-3369945891 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3369945891 revocation-check none rsakeypair TP-self-signed-3369945891 ! ! crypto pki certificate chain TP-self-signed-3369945891 certificate self-signed 01 (cert is here) quit ip source-route ! ! ip dhcp excluded-address 192.168.1.1 ip dhcp excluded-address 192.168.1.5 ip dhcp excluded-address 192.168.1.2 ip dhcp excluded-address 192.168.1.200 192.168.1.210 ip dhcp excluded-address 192.168.1.6 ip dhcp excluded-address 192.168.1.8 ip dhcp excluded-address 192.168.3.1 ! ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 10.171.12.5 10.171.12.37 lease 0 2 ! ip dhcp pool guest import all network 192.168.3.0 255.255.255.0 default-router 192.168.3.1 dns-server 10.171.12.5 10.171.12.37 ! ! ip cef no ip domain lookup no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO891W-AGN-A-K9 sn FTX153085WL ! ! username ESIadmin privilege 15 secret 5 $1$g1..$JSZ0qxljZAgJJIk/anDu51 username user1 password 0 pass ! ! ! class-map type inspect match-any ccp-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-all ccp-insp-traffic match class-map ccp-cls-insp-traffic class-map type inspect match-any ccp-cls-icmp-access match protocol icmp class-map type inspect match-all ccp-invalid-src match access-group 100 class-map type inspect match-all ccp-icmp-access match class-map ccp-cls-icmp-access class-map type inspect match-all ccp-protocol-http match protocol http ! ! policy-map type inspect ccp-permit-icmpreply class type inspect ccp-icmp-access inspect class class-default pass policy-map type inspect ccp-inspect class type inspect ccp-invalid-src drop log class type inspect ccp-protocol-http inspect class type inspect ccp-insp-traffic inspect class class-default drop policy-map type inspect ccp-permit class class-default drop ! zone security out-zone zone security in-zone zone-pair security ccp-zp-self-out source self destination out-zone service-policy type inspect ccp-permit-icmpreply zone-pair security ccp-zp-in-out source in-zone destination out-zone service-policy type inspect ccp-inspect zone-pair security ccp-zp-out-self source out-zone destination self service-policy type inspect ccp-permit ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group 3000client key 67Nif8LLmqP_ dns 10.171.12.37 10.171.12.5 pool dynpool acl 101 ! ! crypto ipsec transform-set myset esp-3des esp-sha-hmac ! crypto dynamic-map dynmap 10 set transform-set myset ! ! crypto map clientmap client authentication list userauthen crypto map clientmap isakmp authorization list groupauthor crypto map clientmap client configuration address initiate crypto map clientmap client configuration address respond crypto map clientmap 10 ipsec-isakmp dynamic dynmap ! ! ! ! ! interface FastEthernet0 ! ! interface FastEthernet1 ! ! interface FastEthernet2 ! ! interface FastEthernet3 ! ! interface FastEthernet4 ! ! interface FastEthernet5 ! ! interface FastEthernet6 ! ! interface FastEthernet7 ! ! interface FastEthernet8 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! ! interface GigabitEthernet0 description $FW_OUTSIDE$$ES_WAN$ ip address 10...* 255.255.254.0 ip nat outside ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto map clientmap ! ! interface wlan-ap0 description Service module interface to manage the embedded AP ip unnumbered Vlan1 arp timeout 0 ! ! interface Wlan-GigabitEthernet0 description Internal switch interface connecting to the embedded AP switchport trunk allowed vlan 1-3,1002-1005 switchport mode trunk ! ! interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-FE 1$$FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly zone-member security in-zone ip tcp adjust-mss 1452 crypto map clientmap ! ! interface Vlan2 description guest ip address 192.168.3.1 255.255.255.0 ip access-group 120 in ip nat inside ip virtual-reassembly zone-member security in-zone ! ! interface Async1 no ip address encapsulation slip ! ! ip local pool dynpool 192.168.1.200 192.168.1.210 ip forward-protocol nd ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! ip dns server ip nat inside source list 23 interface GigabitEthernet0 overload ip route 0.0.0.0 0.0.0.0 10.165.0.1 ! access-list 23 permit 192.168.1.0 0.0.0.255 access-list 100 remark CCP_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 10.165.0.0 0.0.1.255 any access-list 110 permit ip 192.168.0.0 0.0.5.255 any access-list 120 remark ESIGuest Restriction no cdp run ! ! ! ! ! ! control-plane ! ! alias exec dot11radio service-module wlan-ap 0 session Access point version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESIRouter ! no logging console enable secret 5 $1$yEH5$CxI5.9ypCBa6kXrUnSuvp1 ! aaa new-model ! ! aaa group server radius rad_eap server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa group server radius rad_acct server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa authentication login eap_methods group rad_eap aaa authentication enable default line enable aaa authorization exec default local aaa authorization commands 15 default local aaa accounting network acct_methods start-stop group rad_acct ! aaa session-id common clock timezone EST -5 clock summer-time EDT recurring ip domain name ESI ! ! dot11 syslog dot11 vlan-name one vlan 1 dot11 vlan-name two vlan 2 ! dot11 ssid one vlan 1 authentication open eap eap_methods authentication network-eap eap_methods authentication key-management wpa version 2 accounting rad_acct ! dot11 ssid two vlan 2 authentication open guest-mode ! dot11 network-map ! ! username ESIadmin privilege 15 secret 5 $1$p02C$WVHr5yKtRtQxuFxPU8NOx. ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! ssid two ! antenna gain 0 station-role root ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 bridge-group 2 subscriber-loop-control bridge-group 2 block-unknown-source no bridge-group 2 source-learning no bridge-group 2 unicast-flooding bridge-group 2 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache shutdown ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! antenna gain 0 dfs band 3 block channel dfs station-role root ! interface Dot11Radio1.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache ! interface GigabitEthernet0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface GigabitEthernet0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 no bridge-group 2 source-learning bridge-group 2 spanning-disabled ! interface BVI1 ip address 192.168.1.2 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag access-list 10 permit 192.168.1.0 0.0.0.255 radius-server host 192.168.1.5 auth-port 1812 acct-port 1813 key ***** bridge 1 route ip

  Read the article

• Bridging Virtual Networking into Real LAN on a OpenNebula Cluster

  - by user101012

  I'm running Open Nebula with 1 Cluster Controller and 3 Nodes. I registered the nodes at the front-end controller and I can start an Ubuntu virtual machine on one of the nodes. However from my network I cannot ping the virtual machine. I am not quite sure if I have set up the virtual machine correctly. The Nodes all have a br0 interfaces which is bridged with eth0. The IP Address is in the 192.168.1.x range. The Template file I used for the vmnet is: NAME = "VM LAN" TYPE = RANGED BRIDGE = br0 # Replace br0 with the bridge interface from the cluster nodes NETWORK_ADDRESS = 192.168.1.128 # Replace with corresponding IP address NETWORK_SIZE = 126 NETMASK = 255.255.255.0 GATEWAY = 192.168.1.1 NS = 192.168.1.1 However, I cannot reach any of the virtual machines even though sunstone says that the virtual machine is running and onevm list also states that the vm is running. It might be helpful to know that we are using KVM as a hypervisor and I am not quite sure if the virbr0 interface which was automatically created when installing KVM might be a problem.

  Read the article

• windows 8.1 upgrade fails with error code 0xc1900101-0x20017

  - by cmorse

  I just tried to install windows 8.1 on my laptop, but it fails to install with the message: Sorry we couldn't complete the update to Windows 8.1. We restored your previous version of Windows to this PC 0xC1900101 - 0x20017 It looks like on the first boot that the laptop is going to the PC restore screen (it asks what kind of keyboard I have, and then what repair optins I would like to take). Thus far I have just been selecting "Continue to windows 8." I'm running a Lenovo x220i tablet. I've got 43GB of free disk space. It installed just fine on my desktop. The primary difference between the two machines is that the desktop has media center install, and isn't using TrueCrypt. Full WindowsUpdate.log http://pastebin.com/hGmAW4Q1 Most important portion of WindowsUpdate.log: 2013-10-17 10:41:06:671 964 694 Agent ************* 2013-10-17 10:41:06:671 964 694 Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdates] 2013-10-17 10:41:06:671 964 694 Agent ********* 2013-10-17 10:41:06:671 964 694 Agent * Online = No; Ignore download priority = No 2013-10-17 10:41:06:671 964 694 Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1" 2013-10-17 10:41:06:671 964 694 Agent * ServiceID = {7971F918-A847-4430-9279-4A52D1EFE18D} Third party service 2013-10-17 10:41:06:671 964 694 Agent * Search Scope = {Machine & All Users} 2013-10-17 10:41:06:671 964 694 Agent * Caller SID for Applicability: S-1-5-18 2013-10-17 10:41:07:233 964 870 Report REPORT EVENT: {AD47FBDC-F7F9-4E7F-BAF4-DBA3784C7101} 2013-10-17 10:41:06:436-0600 1 202 [AU_REBOOT_COMPLETED] 102 {00000000-0000-0000-0000-000000000000} 0 0 AutomaticUpdates Success Content Install Reboot completed. 2013-10-17 10:41:07:233 964 870 Report REPORT EVENT: {8D4E7A67-9526-4702-A897-5BE5F97497AF} 2013-10-17 10:41:06:639-0600 1 204 [AGENT_INSTALLING_FAILED_POST_REBOOT] 101 {8951E70D-4332-4F7C-B92D-D9362E384959} 1 c1900101 WSAcquisition Failure Content Install Installation Failure Post Reboot. 2013-10-17 10:41:07:249 964 870 Report CWERReporter::HandleEvents - WER report upload completed with status 0x8 2013-10-17 10:41:07:249 964 870 Report WER Report sent: 7.8.9200.16715 0xc1900101(0x20017) 8951E70D-4332-4F7C-B92D-D9362E384959 Install 101 Unmanaged 2013-10-17 10:41:07:249 964 870 Report CWERReporter finishing event handling. (00000000)

  Read the article

< Previous Page | 848 849 850 851 852 853 854 855 856 857 858 859  | Next Page >