Search Results

Search found 34350 results on 1374 pages for 'style issue'.

Page 852/1374 | < Previous Page | 848 849 850 851 852 853 854 855 856 857 858 859  | Next Page >

• How do I connect to a wireless network?

  - by Keith Groben

  I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

  Read the article

• Drawing flaming letters in 3D with OpenGL ES 2.0

  - by Chiquis

  I am a bit confused about how to achieve this. What I want is to "draw with flames". I have achieved this with textures successfully, but now my concern is about doing this with particles to achieve the flaming effect. Am I supposed to create a path along which I should add many particle emitters that will be emitting flame particles? I understand the concept for 2D, but for 3D are the particles always supposed to be facing the user? Something else I'm worried about is the performance hit that will occur by having that many particle emitters, because there can be many letters and drawings at the same time, and each of these elements will have many particle emitters. More detailed explanation: I have a path of points, which is my model. Imagine a dotted letter "S" for example. I want make the "S" be on fire. The "S" is just an example it can be a circle, triangle, a line, pretty much any path described by my set of points. For achieving this fire effect I thought about using particles. So I am using a program called "Particle Designer" to create a fire style particle emitter. This emitter looks perfect on 2D on the iphone screen dimensions. So then I thought that I could probably draw an S or any other figure if i place many particle emitters next to each other following the path described. To move from the 2D version to the 3D version I thought about, scaling the emitter (with a scale matrix multiplication in its model matrix) and then moving it to a point in my 3D world. I did this and it works. So now I have 1 particle emitter in the 3D world. My question is, is this how you would achieve a flaming letter? Is this too inefficient if i expect to have many flaming paths on my world? Am i supposed to rotate the particle's quad so that its always looking at the user? (the last one is because i noticed that if u look at it from the side the particles start to flatten out)

  Read the article

• Cherokee high virtual memory usage even after disabling I/O Cache

  - by nidheeshdas

  I've Ubuntu 10.04LTS 64-bit running on a openvz container and Cherokee 1.0.8 compiled from source. The virtual memory usage of cherokee-worker is around 430 MB even after disabling I/O cache from Advanced - I/O Cache - NOT enabled. Is this issue particular to openvz? Because many people reported to have successfully reduced virt memory usage by disabling io cache. htop output: http://imgur.com/z5JEL.jpg (newbies not allowed to post image.) thanks in advance. nidheeshdas

  Read the article

• How to play audio through a bluetooth headset in Windows 7.

  - by palehorse

  I recently did an in-place upgrade from Vista to Windows 7 RTM. For the most part, things have went brilliantly. The only issue I've been facing is regarding my bluetooth headset, a Dell BH200. The laptop is an Inspiron 1720. I can get Windows 7 to pair with the headset, and even get the bluetooth settings to show that there is stereo audio available. The problem is that the bluetooth headset never shows up in my sound output devices list. I've uninstalled and reinstalled the bluetooth drivers from Dell, tried turning on/off all of the features of the headset, removing the bluetooth driver and letting windows redetect and install but nothing has worked so far. I guess I should mention that the headset worked fine in Vista. Anyone have any ideas?

  Read the article

• Is SEO affected negatively by having densely encoded identifiers of content in URLs?

  - by casperOne

  This isn't about where to put the id of a piece of unique content in URLs, but more about densely packing the URL (or, does it just not matter). Take for example, a hypothetical post in a blog: http://tempuri.org/123456789/seo-friendly-title The ID that uniquely identifies this is 123456789. This corresponds to a look-up and is the direct key in the underlying data store. However, I could encode that in say, hexadecimal, like so: http://tempuri.org/75bcd15/seo-friendly-title And that would be shorter. One could take it even further and have more compact encodings; since URLs are case sensitive, one could imagine an encoding that uses numbers, lowercase and uppercase letters, for a base of 62 (26 upper case + 26 lower case + 10 digits): 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz For a resulting URL of: http://tempuri.org/8M0kX/seo-friendly-title The question is, does densely packing the ID of the content (the requirement is that an ID is mandatory for look-ups) have a negative impact on SEO (and dare I ask, might it have any positive impact), or is it just not worth the time? Note that this is not for a URL shortening service, so saving space in the URL for browser limitation purposes is not an issue.

  Read the article

• public_html permissions for local development

  - by maGz

  I know this question has popped up a couple times, but I can't seem to find a definitive answer to my issue, so please bear with me. I have Ubuntu Server 12.04 setup in VirtualBox for PHP development and testing (Drupal plus other PHP sites using Yii framework). My question is in 3 parts... 1) If I create a public_html folder under /home/myuser, do I need to give ownership of that folder to the Apache www-data group? If so, are there any specific permissions I should be setting? 755? (Btw, I am following this guide to create the public_html directory and set up multiple virtual hosts per site I create and test) I previously had all of my sites under /var/www, but ran into massive permission denied errors whenever I tried to sFTP to it, either through FileZilla or PhpStorm. This is what I had previously done: sudo chgrp www-data /var/www sudo chmod -R 775 /var/www sudo chmod -R g+s /var/www sudo usermod -G www-data [my_ftp_user] 2) The second part of my question is this: If I create my PHP project and files in Windows through PhpStorm, and then upload via sFTP, will permissions get affected? 3) Once I am satisfied with my developed project, would it be advisable to move and test them under /var/www to see how it would fair in a production-ish environment? I would really appreciate the help and advice here. I'm learning more as I go along, but dealing with Linux files and permissions is a bit of a new ballgame for me! Thank you

  Read the article

• Windows Vista Home memory usage problem

  - by lordg

  Hi, I have a Windows Vista Home laptop from a client that is running on 1GB ram. The laptop is used for super basic things, word, internet, outlook, etc. What makes zero sense is that the RAM is being completely consumed, causing the PC to hang sometimes when it can't take it anymore. However, in task manager, the processes appear to only be consuming maybe 100MB (Private Working Set). The client literally has a simple setup, and is running kaspersky, though that does not seem to be indicating it is the cause of the excessive memory usage. Does anyone have a suggestion on how to resolve the memory issue or how to track down what is actually happening and fix it? G

  Read the article

• HTTPS version of page throws 404, regular HTTP appears fine?

  - by Ryan

  I'm having a strange issue with a website in IIS on Windows Server 2003. It has a valid wild card certificate on it, however when I use HTTPS on the page I get a 404 not found. Without HTTPS it shows up fine. Also, if I go to the domain root of the site using HTTP the homepage shows up, but with HTTPS it REDIRECTS ME to a totally different website installed on the same IIS server. I am quite confused. I tried giving each site a unique IP address but it didn't change anything, I also tried changing the SSL ports, no luck. This IIS is setup to run PHP also. What could I check to resolve this?

  Read the article

• vim: highlighting a search term without moving the cursor

  - by ajwood

  Using Vim, I sometimes find myself staring at a section of source code for a while and suddenly want some variable on the screen to pop out. That's easy: /<var> which highlights them all. My issue is that it more often than not the search shifts my window so I'm not looking at the source code from the same place. Even if it's only shifted a few lines, it's still throws me off since I need to take a few seconds to figure out where things have moved to. Is it possible to highlight a search term without moving the cursor to the next match?

  Read the article

• Improving Windows Authentication performance on IIS

  - by flalar

  We're struggling with performance issues with a ASP.NET MVC site that is using Windows Authentication. Response time is very slow on the first request to the site when the user is being authenticated. Further, every time the Authorization header is sent from the browser the response time increases with many seconds. The same issue occurs for both executed files and static content like CSS and JS. Access to the application is restricted to users within a certain role and we are now planning to allow access to static files for all authenticated users to see if that helps. The authentication method in use is NTLM. How should we go forward in pinpointing why authentication decreases performance drastically?

  Read the article

• Rendering artifact when using Eclipse (FlashBuilder)

  - by Demian Brecht

  Once in a while when using FlashBuilder, I'll get a rendering artifact that doesn't go away until I do a full reboot. This artifact seems to be caused by a popup triggered by code documentation popups (hovering over keywords) that linger after the popup has been dismissed: This behavior is seemingly random and incredibly annoying. It only happens when using Eclipse (although I don't run many Java-based programs) and run an NVidia Quadro 2000M (with the latest drivers - figured I'd try that before posting). Has anyone else encountered this issue? Any known solutions?

  Read the article

• Linux RAID0 - relocating member disk

  - by qdot

  I've got an issue I would rather handle with the array online - I am using RAID0 for temporary video storage - data that is low-cost to restore, but that is used frequently. The software array looks like this: md1 : active raid0 sdb1[2] sdc1[3] sdd1[0] sde1[1] 1953487616 blocks 64k chunks I have another partition (sda1) in this system, that I want to use to replace sdc1 (The drives are of varying age, and sdc1 is definitely the slowest one, limiting the entire array's sequential read performance to only 300MB/s). Is there a way to migrate the data from sdc1 to sda1 while the array is still online?

  Read the article

• FTP Active vs passive mode

  - by Dan

  I have a FTP server and while doing testing I found an odd issue that I don't understand. I send a RETR command on file "/Folder1/file.txt" and it works fine. Then I send a RETR command on file "/Folder1/SubFolder1/file.txt" and it times out on transfering the data to the client. This was in active mode. When I switch to passive mode it works fine. I understand the difference between the two modes, but what I don't understand is why it worked for one file in active mode, but not the other. I tried it a dozen times and still got the same results. Any ideas? Thanks!

  Read the article

• MySQL Unions/Subselects not utilizing keys from associated tables

  - by Brett

  I've noticed by doing EXPLAINs that when a MySQL union between two tables is used, mysql creates a temporary table, but the temp table does not use keys, so queries are slowed considerably. Here is an example: SELECT * FROM ( SELECT `part_number`, `part_manufacturer_clean`, `part_number_clean`, `part_heci`, `part_manufacturer`, `part_description` FROM `new_products` AS `a` UNION SELECT `part` as `part_number`, `manulower` as `part_manufacturer_clean`, `partdeluxe` as `part_number_clean`, `heci` as `part_heci`, `manu` as `part_manufacturer`, `description` as `part_description` FROM `warehouse` AS `b` ) AS `c` WHERE `part_manufacturer_clean` = 'adc' EXPLAIN yields this: id select_type table type possible_keys key key_len ref rows Extra 1 PRIMARY <derived2> ALL (NULL) (NULL) (NULL) (NULL) 17206 Using where 2 DERIVED a ALL (NULL) (NULL) (NULL) (NULL) 17743 3 UNION b ALL (NULL) (NULL) (NULL) (NULL) 5757 (NULL) UNION RESULT <union2,3> ALL (NULL) (NULL) (NULL) (NULL) (NULL) In this case, part_manufacturer_clean and manulower are keys in both tables. When I don't use the subselects and union, and just use one table, everything works fine. I'm not sure if the issue is with the union or with the subselects. Is there any way to union two tables and still use keys/indexes for performance?

  Read the article

• Automatically reboot Windows8 if no internet activity [migrated]

  - by Patrick

  I have a media server located in a very inconvenient part of my house. Occasionally I will have to reset my router or it will reset itself. The issue is the PC loses connectivity for some reason, and I am forced to walk outside, around the house, into the basement, over a bunch of toys and weights and boxes, to push a button to reboot it. I would love to have it check itself every 5-10 minutes and auto reboot if it is unable to ping a given address/IP. Any ideas how to accomplish this?

  Read the article

• Using cd Command in Windows Command Line, Can't Navigate to D:\

  - by nicorellius

  This may be a stupid question, and I think I have looked elsewhere to find the answer... Might be a path issue, but when I open the command line and type from the C:\>: cd D:\ I cannot get to the D drive. Even if I type: cd D:\<folder name> The command.exe will auto-complete the line with the tab key, so it knows where I'm at. It just doesn't print to screen the result or actually get me there. This problem exists for the network drives as well. Now, if I use the chdir (cd) command like this: chdir D: or cd d: I get the print out of the D:\ below the command but it still says I'm in the C:\. I feel like I'm missing something simple.

  Read the article

• Joining H264 *without* re-encoding

  - by jdmuys

  I have two halves of a single show in two .MP4 files, encoded in H264. I would like to join them without re-encoding. Is this possible? I managed to create a joined video as a Quicktime file (.mov) using Quicktime Pro, but then Quicktime Pro will not convert it back to .MP4 without re-encoding. This may be because looking inside the .mov file, the two H264 videos are in there still separated as individual "objects". I am also struggling with MPEG StreamClip without reaching a real solution. But I may have missed something. Note that I do not have the same issue with MPEG2 files. I can export them to a .MPEG container or a .TS file for example, and then I can join them without re-encoding using MPEG Streamclip. Any suggestion welcome, preferably using Mac software.

  Read the article

• How to customize live Ubuntu CD?

  - by karthick87

  I would like to customize Ubuntu live CD by installing some additional packages. I have followed this link but it doesn't seems to work. Can anyone provide clear instructions? Thanks in advance! Customization Packages that I want to install: Thunderbird Samba SSH Changes that I need: Remove Games menu from the Application menu Firefox shortcut on desktop Radiance as the default theme Different default Ubuntu wallpaper Note I do not prefer Remastersys, manual way will be appreciated. updates I want the panel to be placed at the bottom. I want to paste my samba configuration file instead of default samba configuration. And i have few firefox shortcuts and Folders, i have to show that in Desktop. Also it will be nice if you say me how to change the icon sets. Recent Updates I have customized ubuntu 10.10 with firefox shortcuts and few folders on desktops. Everything went smooth. But the installer gets crashes after choosing the timezone. How do i fix this issue? Also setting wallpaper affects the login screen. The wallpaper which i set is displayed on the login screen also. I just want the default one for the login screen.

  Read the article

• Exchange 2010 user not receiving mail from another user

  - by eth0

  I have an Outlook 2010 user who can't receive email from another Outlook 2010 user. They are both in the same mailbox server in the same network. They can both send and receive email to anyone else in the organization. One just can't receive from the other. It's very strange. Exchange server was recently migrated from 2007 to 2010 but one of the users described is a new hire which was created on the 2010 server. I have other new hires created on the 2010 server that work fine. I tried having the user send from OWA and it still doesn't get through. What else can I do to troubleshoot this issue? Thank you.

  Read the article

• PC Speaker sounds when machine locks up.

  - by d.c

  What would cause my PC speaker to sound a low frequency continuous tone as my system locks up? Generally what will happen is I'll notice the application I'm using will stop responding but explorer will be partially responsive, then after a few more actions explorer stops responding, and the last click will cause the pc speaker to emit a low constant tone as the machine locks up completely. The only resolve at that point is to restart. Its not a thermal issue, I'm reading the cpu, and hdd temps with software and hardware monitors. AV and malware scans come up clean. I've swapped out my ram, reseated all my components. Used sfc with no results. chkdisk locks up at 3% and defragmenting does the same, but I can read the drive without trouble (I know this as I've done av/malware scans and I also backed everything up since this started happening) I'm mostly just interested to learn, if anyone knows, why the pc speaker would sound during the lock up. windows xp sp2

  Read the article

• Hide directory contents from showing when accessing the URL directly

  - by SoLoGHoST

  On my site, if you browse to http://example.com/images/ the contents of the entire directory are shown like so: How can I make it so that this doesn't show up when people browse directly to http://example.com/images/? Can I create an .htaccess file in that directory? Or is there a better way? I really don't want people being able to do this for the entire site (i.e. every directory on that site). What can I do to prevent this? I figure it's either something that has to be done in Apache or using an global .htaccess file and placing it in the public_html folder perhaps? EDIT I diverted this using an index.php file, but I still feel that security is an issue here, how can I fix this permanently?

  Read the article

• Run script at user login as root, with a catch

  - by tubaguy50035

  I'm trying to run a PHP script as root on user login. The PHP script adds a Samba share to the Samba config, thus the need for root privileges. The only issue here, is that the user doesn't exist yet. This system is integrated with active directory. So when a user logs in for the first time, a home directory for them is created under /home/DOMAIN/username. I've found this question and that seems like the correct way to get what I want, but I'm having trouble with the syntax since I don't know the user's name. Would it be something like: ALL ALL=(ALL) NOPASSWD: /home/DOMAIN/*/createSambaShare.php This doesn't seem to work as it is currently. Anyone have any ideas or a "scripted" way to add a Samba share on user login? Since I've made other changes to /etc/skel, I just added the bash necessary to run the PHP script in .profile in there. This then gets copied to the "new" user's home and it tries to run the PHP script. But it fails, because these are not privileged users. Changing permissions on the PHP script will not help. It needs to be run as sudo because it opens the Samba config file for writing. Letting any user run the PHP script would result in a PHP error. The homes Samba directive doesn't work for my use case. I need the Samba share to exist once they exist on the server, even when they're not logged in.

  Read the article

• Logs being flooded from Squid for having intercepted and authentication enabled together

  - by Horace

  I have done some hefty Google'ing and I can't seem to find a single solution to this issue that I cam currently experiencing. Here is a sample configuration from squid that I have: # # DIGEST Auth # auth_param digest program /usr/sbin/digest_file_auth /etc/squid/digpass auth_param digest children 8 auth_param digest realm LHPROJECTS.LAN Network Proxy auth_param digest nonce_garbage_interval 10 minutes auth_param digest nonce_max_duration 45 minutes auth_param digest nonce_max_count 100 auth_param digest nonce_strictness on # Squid normally listens to port 3128 # Squid normally listens to port 3128 http_port 192.168.10.2:3128 transparent https_port 192.168.10.2:3128 intercept http_port 192.168.10.2:3130 As noted above, I have three ports defined, 2 of them are transparent/intercept and one is a regular http port (which I use for authentication). Which works rather well in this configuration however my logs are getting flooded of this entry authentication not applicable on intercepted requests whenever a transparent connection is made. So far, I can't seem to find any documentation that would describe how to suppress these messages ?

  Read the article

• Frequent occurence of FULL GC.

  - by Viji

  Hi, There is a frequent occurence of FULL GC in our system. We are using Java application running on Tomcat server. Our application is running using internal load balancer setup. We are seeing lot of Full GC's in the server logs due to which the application is hung and Proxy errors are occured. The Java parameter values we are using are: Webapp wrapper: wrapper.java.additional.4=-Xms382M wrapper.java.additional.5=-Xmx1024M Backapp wrapper: wrapper.java.additional.4=-Xms382M wrapper.java.additional.5=-Xmx1024M The error found in webapp wrapper logs: INFO | jvm 1 | 2010/11/26 09:33:19 | [PSYoungGen: 1398460K-140291K(1514624K)] 4623364K-3491394K(5009920K), 0.7285303 secs] [Times: user=1.42 sys=0.00, real=0.72 secs] INFO | jvm 1 | 2010/11/26 09:33:19 | 68539.126: [Full GC DEBUG | wrapperp | 2010/11/26 09:33:19 | send a packet PING : ping Tried to change the JVM values to increase the heap size. But of no use. I suspect that there could be some other reason other than these parameters which is causing the issue. Can anyone please help me on this?

  Read the article

• Make GRUB 2 boot Windows 8 safe mode

  - by Tim

  I have a dual boot configuration: Windows 8 Consumer and Ubuntu 11.10. I tried to install the Asus drivers for my motherboard (P8Z68-V LE EFI) in windows 8, and i now get bluescreens when starting windows. Holding F8 or Shift-F8 doesn't seem to be working, so is there another way to get into Safe Mode, or uninstall the errant driver? I need to get into Safe Mode in windows to fix the issue. Things I have tried: Disabling overclock Holding F8 or Shift+F8 How can i get GRUB 2 to boot windows 8 in safe mode? Or is there another way to disable a driver that is making it impossible to boot?

  Read the article

< Previous Page | 848 849 850 851 852 853 854 855 856 857 858 859  | Next Page >