Search Results

Search found 25123 results on 1005 pages for 'domain model'.

Page 861/1005 | < Previous Page | 857 858 859 860 861 862 863 864 865 866 867 868  | Next Page >

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• Do eSATA HDD docking stations have a capacity limit?

  - by Michael Kjörling

  I'm looking at perhaps buying an eSATA docking station to be able to easily plug in and unplug hard disk drives, particularly but not necessarily only for backup purposes. Note: This is not a hardware shopping recommendation question. Please don't vote to close it as such. Looking at different models, I find for example this page detailing the Deltaco SI-7908SUS which specifically states "storage capacity: 1.5 TB" as well as "pictured hard disk not included, only for illustration". A customer review specifically mentions that it does not work with 3 TB drives, although does not go into any detail such as OS, drive model, etc. From a brief glance, the vendor's web site does not appear to say either way. Then there is the quite similar Deltaco SI-7908B3 which boasts on the box "all 2.5" and 3.5" HDD/SSD compatible". My question is: Why would what basically amounts to a SATA/eSATA adapter have any say in what storage capacity devices are supported? Does it? Assuming the OS supports the full capacity of the drive, why should introducing another (not even a different, really) connector change anything? Bonus question: Might it make a difference if the docking station exposes multiple interfaces (such as in the case of for example the SI-7908SUS exposing USB 2.0 and eSATA)? (I still think it shouldn't, but it'd be nice to have it confirmed.)

  Read the article

• Anonymous file sharing without login window, from Windows 7 server to XP clients

  - by Niten

  I'm trying to provide machines on a small LAN with read-only, anonymous access to files shared from a Windows 7 workstation (let's call it WIN7SVR). In particular, I don't want clients to have to deal with a login window when they navigate to, e.g., \\WIN7SVR in Windows Explorer, but we do not have a domain and synchronizing accounts between the server and clients would be intractable. There are both Windows 7 and Windows XP clients that need access to these shares. I got this working for Windows 7 clients by just enabling the Guest account on WIN7SVR and setting appropriate share permissions. Other Windows 7 machines automatically try logging in as Guest, it seems, so their users don't have to deal with the login window. The problem is with the XP clients--they can access the server if the user enters "Guest" in the login window, but I don't want users to have to do that. So from what I gather, in my limited understanding of Windows file sharing, this boils down to granting null sessions access to file shares on WIN7SVR. But I've had no success so far on that front. I've tried all the following in the local group policy editor on the Windows 7 server: Set Network access: Let Everyone permissions apply to anonymous users to Enabled Set Network access: Restrict anonymous access to Named Pipes and Shares to Disabled Added the names of corresponding shares to Network access: Shares that can be accessed anonymously Added "ANONYMOUS LOGON" to Access this computer from the network under User Rights Assignment Any advice would be highly appreciated... I'm mostly a Unix guy, so I feel somewhat out of my league with Windows file sharing. I do understand that any sort of anonymous access to file shares isn't generally ideal from a security standpoint, but it's the most practical solution for us in this case, and access to our network is well enough controlled that share-level security isn't a concern.

  Read the article

• Use subpath internal proxy for subdomains, but redirect external clients if they ask for that subpath?

  - by HostileFork

  I have a VirtualHost that I'd like to have several subdomains on. (For the sake of clarity, let's say my domain is example.com and I'm just trying to get started by making foo.example.com work, and build from there.) The simplest way I found for a subdomain to work non-invasively with the framework I have was to proxy to a sub-path via mod_rewrite. Thus paths would appear in the client's URL bar as http://foo.example.com/(whatever) while they'd actually be served http://foo.example.com/foo/(whatever) under the hood. I've managed to do that inside my VirtualHost config file like this: ServerAlias *.example.com RewriteEngine on RewriteCond %{HTTP_HOST} ^foo\.example\.com [NC] # <--- RewriteCond %{REQUEST_URI} !^/foo/.*$ [NC] # AND is implicit with above RewriteRule ^/(.*)$ /foo/$1 [PT] (Note: It was surprisingly hard to find that particular working combination. Specifically, the [PT] seemed to be necessary on the RewriteRule. I could not get it to work with examples I saw elsewhere like [L] or trying just [P]. It would either not show anything or get in loops. Also some browsers seemed to cache the response pages for the bad loops once they got one... a page reload after fixing it wouldn't show it was working! Feedback welcome—in any case—if this part can be done better.) Now I'd like to make what http://foo.example.com/foo/(whatever) provides depend on who asked. If the request came from outside, I'd like the client to be permanently redirected by Apache so they get the URL http://foo.example.com/(whatever) in their browser. If it came internally from the mod_rewrite, I want the request to be handled by the web framework...which is unaware of subdomains. Is something like that possible?

  Read the article

• Effective Permissions displays incorrect information

  - by Konrads

  I have a security mystery :) Effective permissions tab shows that a few sampled users (IT ops) have any and all rights (all boxes are ticked). The permissions show that Local Administrators group has full access and some business users have too of which the sampled users are not members of. Local Administrators group has some AD IT Ops related groups of which the sampled users, again, appear not be members. The sampled users are not members of Domain Administrators either. I've tried tracing backwards (from permissions to user) and forwards (user to permission) and could not find anything. At this point, there are three options: I've missed something and they are members of some groups. There's another way of getting full permissions. Effective Permissions are horribly wrong. Is there a way to retrieve the decision logic of Effective Permissions? Any hints, tips, ideas? UPDATE: The winning answer is number 3 - Effective Permissions are horribly wrong. When comparing outputs as ran from the server logged on as admin and when running it as a regular user from remote computer show different results: All boxes (FULL) access and on server - None. Actually testing the access, of course, denies access.

  Read the article

• Windows 7 comments field missing when browsing network

  - by Toymangenie

  I have just purchased three Windows 7 Professional Dell 64-bit PCs for testing prior to upgrading our company’s 120+ PCs from Windows XP Professional. The setup is a standard domain with a Windows Server 2003 32-bit server. We name each PC XP1 to XP150 so that when users join or leave, I don’t have to rename the PC. We use the Description field to allocate the user’s name to each PC. We also have a share set up on each PC using the user’s name. When I browse the network using Windows Explorer in XP, I get a useful display. The left pane showing the PC number and the right pane showing NAME and COMMENTS So, for example I would see: XP01 Fred Bloggs (Each PC on a new row.) The right pane is my main tool for administering the network. I can easily see the PC number and the name of the user. However, in Windows 7, this seems to have been thrown out of the window and replaced with fields that I do not need and in my case always display the same info. "Name", "Category", "Workgroup", "Network Location" In my case the Name column gives the PC number (XP10) etc and all three other columns display identical useless information. So I can’t see who is using XP10. When I am in “help desk” mode, I would naturally ask the user’s name and use my remote desktop client to view their screen. The user isn’t aware of their PC name, so I am finding it impossible to match the user name with a PC number. Any ideas how to overcome this "by design" change to Windows 7?

  Read the article

• CC.NET + SVN : Server certificate issue

  - by MSI

  I am trying to setup Continuous Integration in our office. Being a puny little developer I am facing this supposedly infamous problem: " Source control operation failed: svn: OPTIONS of 'https://trunkURL': Server certificate verification failed: issuer is not trusted" So I tried the following solution - Run CC.NET service (server running as win service) using a domain account (rather than default LOCAL SYSTEMS) and accept cert permanently using command prompt under that user by using svn log/list on the repo. Doesn't help :(. I am getting the following from my artifact/log files(or dashboard) ThoughtWorks.CruiseControl.Core.CruiseControlException: Source control operation failed: svn: OPTIONS of 'https://TrunkURL': Server certificate verification failed: issuer is not trusted (https://ServerAdd) . Process command: E:\(svn.exe Path) log https://TrunkURL -r "{2010-11-08T02:12:20Z}:{2010-11-08T02:13:21Z}" --verbose --xml --no-auth-cache --non-interactive at ThoughtWorks.CruiseControl.Core.Sourcecontrol.ProcessSourceControl.Execute(ProcessInfo processInfo) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.Svn.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModificationsWithLogging(ISourceControl sc, IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModifications(ISourceControl sourceControl, IIntegrationResult lastBuild, IIntegrationResult thisBuild) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.Integrate(IntegrationRequest request) We are using VisualSVN Server and CC.NET for this adventure. Tips, suggestions will be highly appreciated. Thanks

  Read the article

• Automating first time login process in Windows Server 2008 R2 SP1 virtual machine

  - by George Durzi

  I have a set of Windows 2008 Server R2 SP1 Enterprise Edition virtual machines running in Hyper-V. The host server has 64GB of RAM and two SSD drives (one drive for the host OS, and the second one for the VMs). The virtual machines are as follows: Domain Controller: 4GB RAM Exchange Server: 4GB RAM Terminal Services: 50GB RAM We use this setup for a travelling training class where users remote desktop to one of the VMs - let's call it the Terminal Services or "TS" VM - where tools such as Visual Studio are installed. The students go through some labs on the TS VMs in Visual Studio. Overall, this setup works great. However, when users are collectively logging in for the first time, the VM really struggles to keep up while all the user profiles are created. It can take some users up to 10 minutes to login. The number varies from 30 to 40 students. A workaround to this would be to manually remote desktop to the TS virtual machine using all the accounts to ensure that the local profile is created in advance. I'm looking for a way to automate the first time login process on the TS virtual machine. I am envisioning iterating through the accounts in a certain Active Directory OU, and then somehow initiating a remote desktop session to the TS VM to log them in for the first time. Are there ways to do this? Thanks

  Read the article

• Installing and running two postgresql versions on different ports (or two instances of same server)

  - by Andrius

  I have postgresql 9.1 installed on my machine (Ubuntu). I need another postgresql server that would run next to the old one. Exact version does not matter, but I'm thinking of using 9.2 version. How could I properly install and run another postgresql version without screwing old one (like upgrading). So those versions would run independently on different ports. Old one on 5432 and new one on 5433 for example. The reason I need this is for two OpenERP versions databases. If I run two OpenERP servers (with different versions) on single postgresql port, it crashes because new OpenERP version detects old versions database and tries to run it, but it crashes because it uses another schemes. P.S or maybe I could just run same postgresql server on two ports? Update So far I tried this: /usr/lib/postgresql/9.1/bin/pg_ctl initdb -D main2 It created new cluster. I changed port to 5433 in new clusters directory postgresql.conf file. Then ran this: /usr/lib/postgresql/9.1/bin/pg_ctl -D main2 -l logfile start I got response server starting. But when I tried to enter new cluster's template database with: psql template1 -p 5433 I got this error: psql: could not connect to server: No such file or directory Is the server running locally and accepting connections on Unix domain socket "/var/run/postgresql/.s.PGSQL.5433"? Also now when I try to stop server with: /usr/lib/postgresql/9.1/bin/pg_ctl -D main2 -l logfile start I get this error: pg_ctl: PID file "main2/postmaster.pid" does not exist Is server running? So I don't understand if server is running and what I'm missing here? Update Found what was wrong. Stupid me. I didn't notice that when I changed port in .conf file, that line was commented already. So actually I didn't change anything first time, but thought I did and it used default 5432 port.

  Read the article

• SubDomain creation issue.Ubuntu 12.04 Apache 2.22 Webmin

  - by anarchos78

  I have a technical question concerning subdomains. My installation is UBUNTU 12.04 and WEBMIN for administration (using Apache web server). I am trying to create a subdomain to one IP (the domain is www.ithemis.gr and I want to create test.ithemis.gr and/or test1.ithemis.gr) with no success. I think I've tried the right way to set subdomains. The address does not resolving (I have already created DNS records via BIND). Do you have any suggestions? I am very new in server administration. Any help will be greatly appreciated! Apache configuration: In /etc/apache2/sites-available: Conf file:www.ithemis.gr.conf (main website) <VirtualHost 184.171.255.110:80> DocumentRoot /home/ithemis.gr ServerName www.ithemis.gr <Directory "/home/ithemis.gr"> allow from all #Options +Indexes Options +Includes -Indexes </Directory> </VirtualHost> Conf file:www.test.ithemis.gr.conf (subdomain website): <VirtualHost *:80> DocumentRoot /home/test.ithemis.gr ServerName test.ithemis.gr <Directory "/home/test.ithemis.gr"> allow from all Options +Indexes </Directory> </VirtualHost> My DNS records: Master Zone: ithemis.gr Name Type TTL Values ithemis.gr. NS Default ns1.themis.gr. ithemis.gr. A Default 184.171.255.110 ns1.ithemis.gr. A Default 184.171.255.110 ns2.ithemis.gr. A Default 184.171.255.110 mail.ithemis.gr. A Default 184.171.255.110 www.ithemis.gr. CNAME Default ithemis.gr. ithemis.gr. MX Default 5 mail.ithemis.gr. www.test.ithemis.gr. CNAME Default ithemis.gr. test.ithemis.gr. CNAME Default ithemis.gr.

  Read the article

• FTP Server with advanced features

  - by Nikolas Sakic

  Hi, We supply zone-files to our customers. Some zone files are big about 300MB and some are quite small, maybe like 1MB. We had this issue that someone setup a script to continually download the file. Imagine downloading 300MB file a few hundred times a day. Since, we don't have packet-shaper to throttle the traffic, we need to upgrade ftp server and use add-on modules to limit the download somehow. We currently use proftpd server. Also note that there are different users for different domains - say, if you want to download zone file for .INFO domain, then you use a particular user. That user can't download any other zone's file. This is what we are looking for: Have maximum of 400MB download per user per day. Or even have different download limit for different users per day. Have one connection per user at any time. Max # of connection (non-simultaneous) per user per day is 5. Anyone trying to exceed that gets banned for 24 hours. Has anyone used FTP server with similar restrictions above? Does anyone have any ideas where I can start? Any help would be appreciated. Thanks. -N

  Read the article

• Redirect port / port 10000 to https apache

  - by Hamid Elaosta

  I have been reading around and trying different configurations to get a request to my server on port 10000 to redirect a http to a https request. For some reason I can't figure out how to make it happen when i use port 10000 although i can set a rewrite rule for port 80 (implicit) to do it: All I want is a request as follows: http://127.0.0.1:10000 to redirect me to https://127.0.0.1:10000 but it needs to be written so that it also works when accessed via my domain name externally. My current, vhost, the last of many different attempts is currently set as follows, but it doesn't seem to work at all: <VirtualHost *:10000> RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (.*) https://%{HTTP_POST}%{REQUEST_URI} ErrorLog "/var/log/httpd/webmin-redirect_error_log.log" CustomLog "/var/log/httpd/webmin-redirect_access_log.log" common </VirtualHost> I'v also tried a few other things but nothing seems to work, any help would be appreciated. EDIT: I already have a re-write in my httpd.conf that redirects port 80 to https. If I access port 10000 externally it is redirected to https, but from the lan "http://192.168.0.2:10000" it doesnt.

  Read the article

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• Self-connecting printers

  - by Martin Cerny

  Hello, I work as an administrator in a small company using XP Professional on all computers and two servers with Win 2003 Server. Recently a very unusual problam occured one of the computers keeps connecting to all the printers on the network it doesn't matter if it's an administrator or Domain User as soon as somebody logs in the commputer connects all the printers. The printers are either installed on local computers or on the server and shared. There is no log-on script connecting the printers, I install them manualy and none of the other computers shows such behaviour. We have a printer which is installed on two computers and both of them share it (I'm moving it to Server from a small PC which shared it up to now, but some computers still use the old connection), meaning this specific computer connects to one of the printer two times and it can't use either of the connections. How to prevent this self-connecting to all printers (none of the other computers has this problem). If I delte them from the "Printers" folder everything works fine untill I reconnect and the Folder is once again full of all the printers we have. I solved the smaller problem, computer is now capable of printing on all of the printers (it seems there have been some registry issues), after cleaning the registry and reinstalling the printer it seems to work just fine. But the second thing prevails, the computer connects to all the printers in the network (when I remove one/multiple it is reconnected right after the next log-in by any user).

  Read the article

• Toshiba Satellite P755D USB 3.0 Drivers Missing - Windows 7 Professional

  - by nicorellius

  I bought a Toshiba Satellite P755D recently and installed Windows 7 Professional on the machine. It runs great. But I noticed the exclamation point in the yellow triangle icon in the Device Manager next to the Universal Serial Buss (USB) Controller (I'm assuming this is the USB 3.0 controller because mine doesn't recognize devices). Normally, when this kind of thing happens I go to the manufacturer's website and download appropriate drivers and call it a day. But not this time... I browsed to my model and found no driver for the USB 3.0 controller. I tried other HW and Utility drivers, thinking they would be bundled. No luck. I tried looking up the motherboard in my machine. Generic name, no luck. I then called Toshiba technical support and they tried basic troubleshooting, eg, uninstall device, reboot, for auto-installation; no luck. I popped the Windows 7 disk back in and tried to get information that way, no luck. Finally, the technical support guy said he would look into the engineer's system to see if there was a specific driver available and that's where I'm at. The technician told me that these USB 3.0 drivers come within the native driver pack in windows but that doesn't seem to be the case. Any ideas? EDIT - See attached screen shots.

  Read the article

• Postfix character encoding?

  - by Camran

  I use Postfix as a mailserver. I have Ubuntu OS. Then I use PHP to send emails. Problem is that none of my emails are encoded properly by a mailsoftware which my VPS provider uses. According to them, the problem lies with me. It is only the name field which isn't encoded properly. For example "Björn" becomes "Björn" in my emails. However, when I echo the $name, it outputs "Björn" which is correct. Also, gmail and hotmail does show it correctly. The strange part is that the "text" (the message itself) is encoded properly. I use the following for sending mail: $headers="MIME-Version: 1.0"."\n"; $headers.="Content-type: text/plain; charset=UTF-8"."\n"; $headers.="From: $name <$email>"."\n"; $name= iconv(mb_detect_encoding($name), "UTF-8//IGNORE//TRANSLIT", $name); //// I HAVE TRIED WITH AND WITHOUT THE LINE ABOVE, NO DIFFERENCE mail($to, '=?UTF-8?B?'.base64_encode($subject).'?=', $text, $headers, '[email protected]'); I have tried with and without the iconv line also, no luck. The last thing I can think of is POSTFIX, could there be a setting for character encoding there? Anybody knows?

  Read the article

• webmin's bind & nameserver - NS doesn't resolve

  - by user127518

  Got a problem setting up a nameserver. Here are the details: domain http://stagingtestserver.com.au/ (I did some updates and now www.stagingtestserver.com.au won't resolve) I got some errors in www.intodns.com/stagingtestserver.com.au as well. I could not ping ns1. and ns2. also. This is the record file under /var/named/stagingtestserver.com.au.hosts: $ttl 38400 stagingtestserver.com.au. IN SOA ns1.stagingtestserver.com.au myemail\.here.gmail.com. ( 1341370630 10800 3600 604800 38400 ) stagingtestserver.com.au. IN A 202.4.229.161 www.stagingtestserver.com.au. IN A 202.4.229.161 ftp.stagingtestserver.com.au. IN A 202.4.229.161 m.stagingtestserver.com.au. IN A 202.4.229.161 localhost.stagingtestserver.com.au. IN A 127.0.0.1 webmail.stagingtestserver.com.au. IN A 202.4.229.161 admin.stagingtestserver.com.au. IN A 202.4.229.161 mail.stagingtestserver.com.au. IN A 202.4.229.161 stagingtestserver.com.au. IN MX 5 mail.stagingtestserver.com.au. ns1.stagingtestserver.com.au. IN A 202.4.229.161 ns2.stagingtestserver.com.au. IN A 202.4.229.172 stagingtestserver.com.au. IN NS ns1.stagingtestserver.com.au. stagingtestserver.com.au. IN NS ns2.stagingtestserver.com.au. Any thoughts, guys? Thanks and I appreciate all your thoughts/help/(ahem violent) reactions? :)

  Read the article

• Lion MacBook Pro will not load webpages with DNS just after wake

  - by NReilingh

  I'm working with a 2011 MacBook Pro running Lion (10.7.2), that after waking from sleep (i.e. opening the lid) takes an inordinately long amount of time (2-3 minutes or more) to get a usable internet connection. Upon waking, the wi-fi icon signifies it is negotiating a network connection, and completes one a few seconds later. At this point, network diagnostics will not show any issues, and everything in Network preferences looks as normal: I'm connected to the proper network, have the right IP address and gateway, and DNS settings are correct. However, any site accessed with a domain name (like http://www.google.com) in Safari will return the "You are not connected to the Internet." error. Accessing a site directly, say, with Google's 74.125.226.212, is successful. Yet, Network Diagnostics will insist that DNS is functioning properly. After a few minutes, the following lines will be printed to the Console log, and regular behavior will be restored. 11/18/11 8:11:31.288 PM airportd: _doAutoJoin: Already associated to “Wireless”. Bailing on auto-join. 11/18/11 8:11:32.000 PM kernel: en1: BSSID changed to 00:25:9c:63:91:bd This behavior occurs only when waking from sleep--not when turning wi-fi on and off. This problem also occurs when using a wired Ethernet connection. As per this thread, I have tried flushing the DNS cache and wiping the wireless network from memory (it's not a protected network). Neither have worked.

  Read the article

• Exchange 2003: recover mailbox when migrated to 2007

  - by lyngsie

  We have migrated almost all of our mailboxes from Exchange 2003 to 2007 so both are still up and co-existing in our domain. One mailbox is missing some mails, and I tried to recover from an Exchange 2003 backup using ExMerge as usual, but it throws an error: Error opening message store (MSEMS). Verify that the Microsoft Exchange Information Store service is running and that you have the correct permissions to log on. (0x8004011d) This should be normal when a mailbox has been migrated to 2007 and you try to recover a 2003 backup as stated here: http://www.petri.co.il/restoring-exchange-2003-mailboxes-exchange-2007-exmerge.htm We then tried the solution given in the article (copying the value "homemdb" for the user and pasting this in "msExchOrigMDB" for the Recovery Storage Group object in adsiedit). The error unfortuntely persists. So my question is, how can I extract a .pst from a mailbox in the recovery storage group when both Exchange 2003 and 2007 are running? I assume this is why the solution in the article didn't work. If no solution is possible using regular tools (exmerge, eseutil, etc.) which third-party tool should we choose - preferably the cheapest as we only need this one mailbox recovered.

  Read the article

• How to rename network printer on Windows 7?

  - by Adrian McCarthy

  This question is similar to How do you rename a printer device in Windows 7 64 bit, except the answers there do not work, and I'll provide more information. This is a home network, not a domain. I have set up a Brother HL-5170DN. It is a network printer connected directly to an Ethernet hub. I can connect to it with Windows 7, but on Windows 7 it defaults to the name "binary_p1 on Brn37415f", which isn't very useful. And I cannot seem to change the name. I have it working with several Windows XP and Vista machines, and I can change the name on those machines. On Windows 7 Printer properties: I can see the "binary_p1" name on the General tab. I can select the text, but I cannot change it. The field is not grayed out, but I cannot type anything into it. On the Ports tab, all of the controls are grayed out (disabled). The selected Port is called "\\Brn_37415f\binary_p1", and it's described as "Client Side Rendering Provider" and the printer field says "binary_p1". On the Security tab, I can see that my account has "Manage this printer" permissions. If I choose Printer Server Properties, I can select the port and click Configure Port, but I get a dialog that says, "An error occurred during port configuration. This option is not supported." I have found many forums with people asking the same question without getting an answer. Update: No more bounties to offer, but I'm still looking for a solution to this problem.

  Read the article

• What are the "least legally restrictive" well-connected countries to host a website?

  - by monster

  NB: I am aware that this question is subjective, as it can't be defined precisely, but the answers should still be "objective": Country name, and what makes it legally safer. EDIT: A) I am located in Germany. B) I am NOT looking for a place to offer pirated Software/Media; no binary on my site, except "profile icon". Hello! I want to start publishing "social" websites / apps, and I found that the biggest initial problem is this: Any and all services I have to depend on, including Domain Registrar, DNS provider, Server/Cloud Provider, CDN Provider, ... even my Insurance Agent, basically say that they can "throw me out" if my website contains "unacceptable" content. It's always phrased in such a way that basically anything can fall under "unacceptable" content. This is very frustrating because you just can't fully control what users post on your "social website", and you so you basically have to expect when you go to bed that your site is going to be gone when you wake up. I've heard a lot of horror stories about this. Since the "Terms Of Service" of all those providers are foremost to protect themselves from legal actions, and those legal actions depend on the country where they are located, it seems like the first step is to find which country is the "safest" to locate a site. "Safest" being defined as, where I am least likely to get in legal trouble with the local authorities, if some user posts something unacceptable in some way. The main restriction is that it should also be a "well-connected" country, because there is no point in being "safe", if my users can't get to my sites, or the latency is unacceptable. I am targeting the English speaking people in any country as my future users.

  Read the article

• datawind ubislate 9ci tablet computer hanging on boot

  - by user57924

  I am new to this forum. I purchased a new tablet Datawind Ubislate 9ci. It is a 9 inch no-bluetooth tablet. Details: Android 4.1.1 Rock chip RK2928 KERNEL linux version 3.0.36 I was trying to install CWM through mobile odin and ROM manager but my tablet was not supported so i downloaded build.prop editor from google play and changed it to some other cwm recognizable model viz. Samsung, nexus etc. When i was doing the above mentioned procedure, suddenly my tablet is coming up to bootloading and hanging there only and not opening i went to recovery and tried to do wipe data factory reset but failed to get opened after boot android system recovery(3e) has the following options 1)reboot system now 2)apply update from ADB 3)apply update from external storage 4)update rkimage from external storage 6)wipe data factory reset 7)wipe cache partition 8)recovery system from back up i tried to do wipe data factory reset 2-3 times but still hanging at boot i had not made any back up before this bootloop and also tried hard reset by pressing needle at the back please somebody help me to get rid of this problem and also tell me how to unlock bootloader thank you

  Read the article

• Files deleted. What could have happened?

  - by jjfine

  I'm having a weird issue today. I was writing and testing out some simple cgi scripts this morning when I realized that I couldn't run them from one of the other computers on the (windows) network. So I had my network admin come in and take a look at what was going on. A few minutes later a co-worker came in and told me that a bunch of files he was working with as well as a bunch of others (all *.c files) on the network drive got deleted. He also noticed some strange apache_dump_500.log.txt files in the same directories where the files got deleted. The apache_dump_500.log.txt files all look like this: REDIRECT_HTTP_ACCEPT=*/*, image/gif, image/x-xbitmap, image/jpeg REDIRECT_HTTP_USER_AGENT=Mozilla/1.1b2 (X11; I; HP-UX A.09.05 9000/712) REDIRECT_PATH=.:/bin:/usr/local/bin:/etc REDIRECT_QUERY_STRING= REDIRECT_REMOTE_ADDR=<my computer's local ip> REDIRECT_REMOTE_HOST= REDIRECT_SERVER_NAME=<my computer's domain url> REDIRECT_SERVER_PORT= REDIRECT_SERVER_SOFTWARE= REDIRECT_URL=/cgi-bin/trojan.py I looked and I don't have any trojan.py in my cgi-bin folder. And all my apache logs are clean. Windows event logger seems to not have any traces of what happened either. My httpd.conf: http://pastebin.com/Yny2Yh8v I think we've got some kind of virus that added this trojan.py file to my cgi-bin, ran the script, and deleted the script and any traces from the logs. Is this a thing that happens? Any ideas whatsoever would be much appreciated!

  Read the article

• Strange RDP / Remote Desktop problem

  - by John Landheer

  I'll try to be as specific as I can be: Server is running SBS 2008 R2 (with all updates) Server is connected to the internet Server has 2 NIC's, one is disabled Server is running RDP Service (accessible directly from the internet, I know, not as secure as it should be) Computers A and B are on the same local net. Computers A and B are both Windows 7. Users X and Y are both admins on the server Computer A can connect as user X to the server with mstsc Computer A can connect as user Y to the server with mstsc Computer B can connect as user X to the server with mstsc Computer B CANNOT connect as user Y to the server with mstsc! Error that username/password is incorrect. The last point is the problem, I get an authentication error. This used to work flawlessly for the last year. The server and desktops have been rebooted. EDIT: I tried: prefixing domain to the username prefixing the server computer name to the username change the password copy/paste the password from notepad to make sure it was correct I find it very strange.... EDIT: The computers are not on the same subnet as the server. The server is at my hosting provider. All computers as all users can reach the web app that is running on the server.

  Read the article

• Windows7 corrupted profile - prevention exists?

  - by Radek

  I have dedicated Windows7 (not on domain) virtual machine for overnight automation testing. Some commands (mySQLdump, tscon.exe) must be run under administrator account. Last week administrator account's profile was corrupted. I fixed it by renaming it in the registry and logging in as administrator. And today it is corrupted again. I use administrator account only to run above commands via runas. Also the computer is restarted via cmd - shutdown command - quite often. Especially every night before automation testing starts. I checked the comp for viruses - did full scan using avast although I believed that the comp is clean. Any idea how to prevent the profile to get corrupted again? update So the first log entry in event log is today from 1.15am and one of my scripts ran runas command as administrator exactly at 1.15am. It was second time that runas war executed though after the testing started. The same happened second day in a row. Before the testing starts I need to copy one file that is locked. So I run handle.exe from runas to unlock it. That is what I think causing the profile to get corrupted. I am not able to reproduce it by myself. The message from event viewer is Windows cannot load the locally stored profile. Possible causes of this error include insufficient security rights or a corrupt local profile. DETAIL – The process cannot access the file because it is being used by another process.

  Read the article

< Previous Page | 857 858 859 860 861 862 863 864 865 866 867 868  | Next Page >