Search Results

Search found 25039 results on 1002 pages for 'machine learning'.

Page 869/1002 | < Previous Page | 865 866 867 868 869 870 871 872 873 874 875 876  | Next Page >

• Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

  - by Brian Stinar

  I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

  Read the article

• How to set up simple VPN for secure Internet connections over unencrypted Wi-Fi on Windows?

  - by Senseful

  I'm looking for a solution similar to the one in this question, except that I don't have a linux computer. I have windows computers that could be set up to accept VPN connections. Preferably I want to set this up on either Windows Server 2003 or Windows XP. I'd like to connect different devices (e.g. iPhone, iPad, laptops, etc.) that are on open unsecure wireless networks (e.g. the one's you see at places like Starbucks) to this VPN to ensure that all my data is secure. I found an article that shows that you can enable VPN connections on Windows XP. After following those steps, though, I'm not sure what to do. Which ports do I open on my firewall? Which VPN settings do I use on my devices such as the iPhone? Do I use L2TP, PPTP, or IPSec? What's the difference between these? Are there any other steps missing in that tutorial? I'm hoping that since Windows has this built in feature, that it will be much simpler to set up rather than having to deal with setting up something such as OpenVPN. If I follow those settings and enable port forwarding on port 1723, and then use the following settings on the iPhone: PPTP (IP Address) RSA SecurID: Off Encryption Level: Auto Send All Traffic: On Proxy: Off It shows "Connecting..." then "Disconnecting..." and the following error message: VPN Configuration A connection could not be established to the PPP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I'm using a user account that I enabled privileges to in the VPN settings on the Windows machine.

  Read the article

• can't ssh from mac to windows (running ssh server on cygwin)

  - by Denise

  I set up an ssh server on a fresh windows 7 machine using the latest version of cygwin. Disabled the firewall. I can ssh into it from itself, from a different windows box (using winssh), and from a linux vm. In spite of that, I tried to ssh in from two different macs, and neither would let me! This is the debug output: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 3dbuild [172.18.4.219] port 22. debug1: Connection established. debug1: identity file /Users/Denise/.ssh/identity type -1 debug1: identity file /Users/Denise/.ssh/id_rsa type 1 debug1: identity file /Users/Denise/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5 debug1: match: OpenSSH_5.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '3dbuild' is known and matches the RSA host key. debug1: Found key in /Users/Denise/.ssh/known_hosts:43 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /Users/Denise/.ssh/identity debug1: Offering public key: /Users/Denise/.ssh/id_rsa Connection closed by [ip] It shows the same output, and fails at the same place, whether I have put my public key on the ssh server or not. Any help would be appreciated-- hopefully someone has run into this before?

  Read the article

• Webserver python update script

  - by ThePyCoder

  So i have made this website on which you can trade stocks based on real stock quotes with virtual money. The stock quotes are in a MySQL database and are updated using a python script which runs every minute or so. Now, this works fine on my local machine with xampp but how about moving the project to a commercial web server? Basically I want my page hosted by a professional company but do those kind of servers support python scripts running in the background? Because a dedicated server would be to expensive and the script does some other sql tasks too so it can't be replaced by PHP or so... So, are there any good web hosting services out there who give me the possibility of running a script in the background and hosting a website in the foreground? For what server specifications do i have to look for? Thnx in advance! PS: I've done some research, and I found a python supporting web host WITH ssh support. Is that what I need? Or is the ssh not allowed to start processes?

  Read the article

• Hanging of host network connections when starting KVM guest on bridge

  - by Chris Phillips

  Hi, I've a KVM system upon which I'm running a network bridge directly between all VM's and a bond0 (eth0, eth1) on the host OS. As such, all machines are presented on the same subnet, available outside of the box. The bond is doing mode 1 active / passive, with an arp_ip_target set to the default gateway, which has caused some issues in itself, but I can't see the bond configs mattering here myself. I'm seeing odd things most times when I stop and start a guest on the platform, in that on the host I lose network connectivity (icmp, ssh) for about 30 seconds. I don't lose connectivity on the other already running VM's though... they can always ping the default GW, but the host can't. I say "about 30 seconds" but from some tests it actually seems to be 28 seconds usually (or at least, I lose 28 pings...) and I'm wondering if this somehow relates to the bridge config. I'm not running STP on the bridge at all, and the forwarding delay is set to 1 second, path cost on the bond0 lowered to 10 and port priority of bond0 also lowered to 1. As such I don't think that the bridge should ever be able to think that bond0 is not connected just fine (as continued guest connectivity implies) yet the IP of the host, which is on the bridge device (... could that matter?? ) becomes unreachable. I'm fairly sure it's about the bridged networking, but at the same time as this happens when a VM is started there are clearly loads of other things also happening so maybe I'm way off the mark. Lack of connectivity: # ping 10.20.11.254 PING 10.20.11.254 (10.20.11.254) 56(84) bytes of data. 64 bytes from 10.20.11.254: icmp_seq=1 ttl=255 time=0.921 ms 64 bytes from 10.20.11.254: icmp_seq=2 ttl=255 time=0.541 ms type=1700 audit(1293462808.589:325): dev=vnet6 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.604:326): dev=vnet7 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.618:327): dev=vnet8 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x130079 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0xc1 data 0xffdd694a kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x530079 64 bytes from 10.20.11.254: icmp_seq=30 ttl=255 time=0.514 ms 64 bytes from 10.20.11.254: icmp_seq=31 ttl=255 time=0.551 ms 64 bytes from 10.20.11.254: icmp_seq=32 ttl=255 time=0.437 ms 64 bytes from 10.20.11.254: icmp_seq=33 ttl=255 time=0.392 ms brctl output of relevant bridge: # brctl showstp brdev brdev bridge id 8000.b2e1378d1396 designated root 8000.b2e1378d1396 root port 0 path cost 0 max age 19.99 bridge max age 19.99 hello time 1.99 bridge hello time 1.99 forward delay 0.99 bridge forward delay 0.99 ageing time 299.95 hello timer 0.50 tcn timer 0.00 topology change timer 0.00 gc timer 0.04 flags vnet5 (3) port id 8003 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags vnet0 (2) port id 8002 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags bond0 (1) port id 0001 state forwarding designated root 8000.b2e1378d1396 path cost 10 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 0001 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags I do see the new port listed as learning, but in line with the forward delay, only for 1 or 2 seconds when polling the brctl output on a loop. All pointers, tips or stabs in the dark appreciated.

  Read the article

• Organizing automatically Windows Files and Folders

  - by Kiquenet

  For Windows only, Organizing the eleventy-billion files you've got stuffed into folders on your hard drive is very "hard". For example, I have one folder on my computer that I save all web downloads to, regardless of file type, size or purpose. Many of the files are only temporary downloads, for instance setup files of applications that I test, demonstration videos that I watch once or documents that I want to read. Some files on the other hand are there to stay, and I used to move them out of the download folder manually in the past. Another files in folders in my computer: many source code, tests, programs, tools, ... I need tecnology for organize billion files. Which best tools for organize, sort, etc automatically your files-folders? Digital Janitor http://davidevitelaru.com/software/digital-janitor/ Belverede http://lifehacker.com/5510961/how-to-automatically-clean-and-organize-your-desktop-downloads-and-other-folders Download Mover http://www.neoteo.com/download-mover-reorganiza-tus-descargas-14188 File/Folder Date Organizer http://seedling.dcmembers.com/other/ffdorg.zip DropIt http://www.lupopensuite.com/db/dropit.htm Others issues about organization files, desktop, etc How to automate the process of organizing audio files on Windows Organizing My Windows Desktop What's a good way for organizing PDF documents on Windows? Folksonomy tagging for files What is your method of “folksonomy” tagging for files on your local machine?

  Read the article

• ssd firmware, linux: updating large batch of drives

  - by wryfi

  I was recently hit with a fatal firmware bug that affected dozens of Crucial SSDs deployed in my datacenter. Many of the affected machines use LSI or other proprietary SAS controllers, which Crucial's bootable ISO does not recognize. None of the affected machines has a Windows license. The story is roughly similar for other SSD mfrs, including Samsung and Intel. To resolve this issue, I was forced to stop each machine, remove the affected SSD, remove the SSD from its hotswap caddy, install it temporarily into my ThinkPad, flash the firmware, reverse, rinse, repeat. It took the better part of a day to get through all the affected devices. I am looking for hardware, software, and/or purchasing strategies to ease this pain, as SSD firmware bugs seem inevitable, and our SSD footprint is growing. My first thought is to get a laptop with eSATA and one of these cables (http://www.newegg.com/Product/Product.aspx?Item=N82E16812311004). That should at least make it so I don't have to remove the drives from their caddies. Surely others have run into this. Any novel solutions?

  Read the article

• Netbook (Samsung N220) on Ubuntu 10.04 slows down WiFi for other computers

  - by Joachim

  I encountered a really odd problem with my new netbook. I am running Ubuntu 10.04 on a Samsung N220 Mito. So far everything worked fine. Now I tried the machine for the first time in our work group where we have a wifi (with internet access) for all laptops. The wifi is controlled by a computer running Suse 9.3 which provides a DHCP server and imposes a firewall. At the moment there is only a macbook in the wifi, where no problems with the internet or wifi connection are encountered. Now coming to my actual problem: In addition to the macbook i connect the Samsung N220 to the Wifi. Problem: My download speed is for some reason limited to 70KB/s max. This is neither a limitation of the server/website i browse on, nor a configuration of the netbook: at home i have 500KB/s download speeds. Furthermore, it is not a default limitation for "untrusted" or "new machines" in the wifi, as for instance other new laptops get full speed internet with our wifi. Problem: Once the Samsung N220 is generating traffic in the wifi, the wifi is slowed down dramatically for all other machines: I run a ping to the router from the macbook. The ping times with the N220 ideling are 2-6ms. When I start downloading or browsing in the web with the N220 the ping speed drops to 800ms. Vice versa, when the macbook is generating the traffic the ping of the N220 to the rooter stays constant at around 2-6ms. So clearly, it is some problem originating from my netbook or maybe its treatment in the wifi. Thanks for any help

  Read the article

• IIS / Virtual Directory authentication.

  - by Chris L

  I have an IIS(v6)/Windows 2003/.Net 3.5(app code, libraries etc.) server hosting a website at www.mywebsite.com mapped to E:\Inetpub\wwwroot\mywebsite, we also have a virtual directory (VirtDir) mapped out to E:\Inetpub\wwwroot\mywebsite\files (although in theory this could be in a different directory or a separate machine) where we store a customer's files(a bunch of .pdf & .xls). Currently to access a file you can enter into the url something like: www.mywebsite.com/VirtDir/Customer/myFile.pdf and get access to the file. The problem is the user doesn't have to log into www.mywebsite.com to get access to the file, we would prefer them to log in first. We would like the user to login via the mywebsite and if valid, let them download files from the virtual directory. The www.mywebsite.com and VirtDir are separate sites on the same farm. Allow Anon Access, and Integrated Windows Authentication both enabled. I'm more of a developer and less of a Sys Admin, but hopefully I'm in the right spot, any help would be appreciated.

  Read the article

• Does the OSS Backup Solution amanda.org support sparse files?

  - by user97961

  I want to (or better have to) do Backups of my KVM Virtual Machine images. I have searched for days for a good Backup Soloution. I know amanda is a very good solution. It would be kinf if someone kenn tell me if the following is supported: Trigger the Creation of LVM Snapshot (by invoking a Shell Script that I will write for that purpose) Do a Differential/Delta Backup on my KVM LVM qcow2 sparse file. = I only want to copy the actually changed bits/bytes (=Delta Backup). And it has to support that the file to be backuped up is a sparse file. (Rsync seems to have some kind of problems in regard to this (if the file does not exist yet on the other side... Then it will create a full file, not a sparse file)) Release the LVM Snapshot (By invoking a Script that I will write for that purpose) It's strange, I have nowhere found any documentation about this fact when searching the internet. Zmanda (Commercial Edition) has support vom XEN VM Backup (but not for KVM as far as I can tell)...

  Read the article

• Wake on LAN Problem

  - by Caley Woods

  I'm working to get wake on lan (wol) working so that we can do some power management at my workplace. I've enabled WOL on a test laptop running Win 7 x64 and put it to sleep and hibernate both with no luck. I'm using a 3rd party utility and I've ran wireshark on the test laptop with it booted up and I can see the WOL packets coming in and the machine refuses to wake from sleep or hibernate. I thought maybe it was the computer I was using so I had another Win 7 x64 laptop nearby and I tried it, same scenario. We're in a cisco environment and I believe I gotten all the pieces in place since I'm seeing the WOL packets come through. I've tested two machines on the same subnet to eliminate the possibility of a misconfiguration on the switch, this also has the same behavior. The laptop models are a Compaq 6510b and 6730b. Is there something I'm missing? I'm trying this across UDP port 50200 since that's the port the actual management system will use after I get it working.

  Read the article

• Membership in two domains

  - by imagodei

  Hello! I would your suggestions for an effective solution for a person, who needs to access resources in two Windows domains and wants to use one computer. It's about our CEO, who has accepted a second position in another company. Accessing files and folders isn't big problem. The greatest challenge I see is that he wants to conveniently access Exchange accounts in both companies; he would like to send and receive mail in single Outlook if possible (two profiles?) There is also a challenge with calendars: he would like to have one calendar for all activities from both Exchange accounts. Creating a POP3 account for accessing second Exchange server is a last resort, because obviously there is a problem with scheduling meetings and other calendar related tasks. Forwarding and receiving all mail/tasks on primary Exchange server is inconvenient because simple replying to original sender is disabled; and also when manually changing the recepient, he will receive mail from the wrong address. We were considering Virtualisation, that is setting up an instance of virtual machine inside existing installation and then joining this virtual computer to a second domain. Then installing another MS Outlook. This would of course mean two different Outlook accounts, two different calendars, but would at least enable our CEO to access all information from a single laptop. Does anyone have any other idea? I know setting up two domains on a single computer is a no-go (without much hacking at least), but effective workarounds are appreciate. The thing I am looking here is high usage/efficiency/productivity, but also as elegant solution from the administration point of view. Thank you very much (if you managed to read this through, this is a good sign ^_^ )

  Read the article

• IIS SMTP server (Installed on local server) in parallel to Google Apps

  - by shaharru

  I am currently using free version of Google Apps for hosting my email.It works great for my official mails my email on Google is [email protected]. In addition I'm sending out high volume mails (registrations, forgotten passwords, newsletters etc) from the website (www.mydomain.com) using IIS SMTP installed on my windows machine. These emails are sent from [email protected] My problem is that when I send email from the website using IIS SMTP to a mail address [email protected] I don’t receive the email to Google apps. (I only receive these emails if I install a pop service on the server with the [email protected] email box). It seems that the IIS SMTP is ignoring the domain MX records and just delivers these emails to my local server. Here are my DNS records for domain.com: mydomain.com A 82.80.200.20 3600s mydomain.com TXT v=spf1 ip4: 82.80.200.20 a mx ptr include:aspmx.googlemail.com ~all mydomain.com MX preference: 10 exchange: aspmx2.googlemail.com 3600s mydomain.com MX preference: 10 exchange: aspmx3.googlemail.com 3600s mydomain.com MX preference: 10 exchange: aspmx4.googlemail.com 3600s mydomain.com MX preference: 10 exchange: aspmx5.googlemail.com 3600s mydomain.com MX preference: 1 exchange: aspmx.l.google.com 3600s mydomain.com MX preference: 5 exchange: alt1.aspmx.l.google.com 3600s mydomain.com MX preference: 5 exchange: alt2.aspmx.l.google.com 3600s Please help! Thanks.

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• Cant kill process on Windows Server 2008!! - Thread in Wait:Executive State

  - by adrian

  I hope someone can help me with our issue we are having. We have a major issue with a process that we can not kill and the only way to get rid of the process is to reboot the machine. I have tried killing it from the normal task manager but no joy. I have tried killing it using the taskkill /F command from a command prompt and no joy. The command reports as sucessful but the process remains. I have tried to start task manager with system rights by calling "psexec -s -i -d taskmgr" and attempting to kill the process but no joy I have tried killing it from Process Explorer but again the process remains. I have tried creating a scheduled task that runs under the SYSTEM name to kill the task but that also does not kill it : schtasks /create /ru system /sc once /st 13:16 /tn test1 /tr "taskkill /F /PID 1576" /it Nothing I do will kill this process. Even logging off and logging back on will not kill this process. Using Process Explorer I notice that there is on stubborn thread that is in the Wait:Executive state. I have tried to kill this thread using Process Explorer but again no joy. We are using Windows Server 2008 R2 64-Bit. The server is brand new and windows is freshly installed. Now heres the thing. We have brought two identical servers from Dell with the same specs and the same OS installed and I can not replicate this issue on the other server. Only on this server, under certain circumstances does this server process hang and can not be restarted! I have also changed the compatability mode by setting it the process to "Windows 2003" but this has not helped. I have noticed in Process Explorer that DEP is turned on but im not sure this has got any bearing on the issue ot not. Please, can someone help??

  Read the article

• vim coloring for git

  - by kelloti

  I'm on Windows and my vim loads with a terrible colorscheme with vim. The message is blue on black (so I can't see what I'm typing). I need to change the colorscheme, but :colorscheme slate doesn't do anything. :version vim - vi improved 7.3 (2010 aug 15, compiled oct 27 2010 17:51:38) ms-windows 32-bit console version included patches: 1-46 compiled by bram@kibaale big version without gui. features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent +clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv +cscope +cursorbind +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +gettext/dyn -hangul_input +iconv/dyn +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse -mouseshape +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +persistent_undo -postscript +printer -profile -python -python3 +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl -tgetent -termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -xfontset -xim -xterm_save -xpm_w32 system vimrc file: "$vim\vimrc" user vimrc file: "$home\_vimrc" 2nd user vimrc file: "$vim\_vimrc" user exrc file: "$home\_exrc" 2nd user exrc file: "$vim\_exrc" compilation: cl -c /w3 /nologo -i. -iproto -dhave_pathdef -dwin32 -dfeat_cscope -dwinver=0x0400 -d_win32_winnt=0x0400 /fo.\objc/ /ox /gl -dndebug /zl /mt -ddynamic_iconv -ddynamic_gettext -dfeat_big /fd.\objc/ /zi linking: link /release /nologo /subsystem:console /ltcg:status oldnames.lib kernel32.lib advapi32.lib shell32.lib gdi32.lib comdlg32.lib ole32.lib uuid.lib /machine:i386 /nodefaultlib libcmt.lib user32.lib /pdb:vim.pdb -debug My $HOME\_vimrc looks like colorscheme slate syn on set shiftwidth=2 set tabstop=2 and my $VIM\vimrc is the stock vimrc that comes with the Windows Vim distribution. How do I change my console Vim colorscheme? Especially for Git commits.

  Read the article

• Configure IIS site to work with host header & hosts file entry

  - by HarveySaayman

  I'm I bit of an IIS / Web noob (I'm a C# backend service / winforms dev) so please bare with me :-) I've set up a site in IIS on my local dev machine. In the bindings section of the site ive added 4 bindings, all 4 for http: Host Name Port IP Address blog.sourcecube.co.za 26581 * www.blog.sourcecube.co.za 26581 * blog.sourcecube.co.za 26581 127.0.0.1 www.blog.sourcecube.co.za 26581 127.0.0.1 in my hosts file (drivers\etc\hosts), i've added the folling entries: 127.0.0.1 blog.sourcecube.co.za 127.0.0.1 www.blog.sourcecube.co.za when i ping my domain name from the command line it does in fact resolve to the loopback address, 127.0.0.1. So what I'm expecting to happen when i navigate to blog.sourcecube.co.za in my browser is for it to resolve to 127.0.0.1, and when the request hits IIS, it should know which site to serve because of the host header? But when i navigate to blog.sourcecube.co.za, i get an "Unable to connect, Firefox can't establish a connection to the server at blog.sourcecube.co.za" error. What am I doing wrong? --- UPDATE --- Navigating to blog.sourcecube.co.za:26581 from my browser works... I'd like get it working without specifying the port number though.

  Read the article

• Why does Windows Firewall want to block Google Chrome today?

  - by hippietrail

  I've been using the same public Wi-Fi (staying in a guesthouse) for over a week now. But this morning for the first time I got this puzzling warning from Windows Firewall: Why does Windows Firewall want to block one of the world's most popular web browsers today after being fine with it for years, and being fine with it on this connection for a week? Could it hinge on the words, some features? If so could it be something like a rare or new feature of Chrome that uses a different HTTP port? And if so why doesn't the security alert tell me any more about it? Or could it be a known bug in Windows Firewall? Or perhaps a known virus etc attaching itself to Google Chrome? Or is there a chance it's related to "Other browser makers follow Google's lead, revoke rogue certificates"? I haven't restarted Chrome for days and have downloaded but not installed a Windows update from a few days ago. So I'm not sure what may have managed to change on my machine since yesterday.

  Read the article

• How do I install Windows XP from an external hard drive?

  - by Plasmer

  I'm trying to install Windows XP Media Center edition by copying the install disc image to an external hard drive and making it bootable. Has anyone had success getting this to work on systems that can't boot from dvds/floppies? I'm basically working from this guide: http://www.dl4all.com/other/21495-install-windows-xp-from-usb.html Update - 2/15/10 I used WinToFlash on my laptop to format my usb hard drive from my install dvd (Windows XP Media Center Version 2005 with Update Rollup 2 from Dell) and selected "boot from usb device" at the boot selection menu and the windows installer started up. However, an error message came up saying that: "A problem has been detected and windows has been shut down to prevent damage to your computer." Originally on my desktop machine, I had 1 150Gb SATA drive, and 2 150 Gb SATA drives striped together using RAID. From the hard drive diagnostics, it appears the windows install on one of the RAIDed disks lost a block and this has been preventing me from booting up. I replaced the standalone drive with a new 1Tb SATA drive and disconnected the other hard drives. Could the message be indicating a virus is on the unformatted drive? or the usb hard drive? Update 2 - 2/15/10 The external hard drive didn't find any viruses when scanned. I tried installing Vista Home Premium 64bit SP1 using WinToFlash and that installed successfully onto the new 1Tb drive. WinToFlash was really easy to use and helped a lot, thanks!

  Read the article

• SVN, Samba and Symbolic Links. How to get them all to play together?

  - by Camsoft

  I've got a website project under version control that relies on files from an unversioned directory on the same server via Symbolic Links. I'm currently storing the symbolic links in the repository. The idea is that if someone checks out a working copy on to the same server they can edit and test the working copy of the project before committing it back to the repository. When they checkout their working copy it successfully sets up the symlinks so that the entire site works when testing. The users that work on the project are Windows users, so I've set a samba shares on the server and then mapped them to network drives in Windows. People can edit their working copies directly on the server via network shares and then test them in the web browser before committing their changes back to the repository via TortoiseSVN. The Problem The problem I have is that Samba resolves the symlinks as expected but when a user tries to commit their changes back to the repository, TortoiseSVN thinks the linked files are part of the project and tries to commit the target files to the repository and not the symlinks themselves. I tried turning off symlink support in samba which means that the linked files cannot be resolved as I don't really want people to have access to the linked files nor do I want to import the linked files in the repository. The problem with this is that I get Can't stat '\webserver\projects\working\project\symlinked_file.php'. Access is denied Apart from the symlink problem everything else works 100% perfectly. Users can either checkout website projects to their machine and work on them (but can't test) or checkout them out to their space on the dev web server and work on them and fully test. So I don't want to change the workflow process, I just need a solution to the symbolic link issue. Many thanks. Originally posted on StackOverflow: http://stackoverflow.com/questions/2400917/svn-samba-and-symbolic-links-how-to-get-them-all-to-play-together

  Read the article

• Folder redirection GPO doesn't seem to be working

  - by user57999

  I've been trying to set up roaming profiles and folder redirection, but have hit a bit of a snag with the latter. This is exactly what I've done so far: (I have OU permissions and GPO permissions over my division's OU.) Created a group called Roaming-Users in the OU 'Groups' Added a single user (testuser) to the group Using the Group Policy Management tool (via RSAT on Windows 7) I right-clicked on the Groups OU and selected 'Create a GPO in this domain, and Link it here' Added my 'Roaming-Users' group to the Security Filtering section of the policy. Added the Folder Redirection option, specifically for Documents. It is set to redirect to: \myserver\Homes$\%USERNAME%\Documents (Homes$ exists and is sharing-enabled). Right-clicked on the policy under the Groups OU and checked Enforced. Logged into a machine as testuser successfully. Created a simple text file, saved some gibberish, logged off. Remoted into the server with Homes$ on it, noticed that the directory Homes$\testuser was created, but was empty. No text file to be found. From what I've read, I did everything I aught to...but I can't quite figure out the issue. I had no errors when I logged off about syncing issues (offline files is enabled) or anything, so I can only imagine my file should have ended up up on the share. Any ideas? EDIT: Using gpresult /R, I confirmed the user is in fact part of the Roaming-Users group, but does not have the policy applied, if that helps. EDIT 2: Apparently you can't apply GPOs to groups...so I applied to users and used the same security filter to limit it to my test user. Nothing happens as far as redirection goes, but I now have the following error in the event log: Folder redirection policy application has been delayed until the next logon because the group policy logon optimization is in effect

  Read the article

• Start & shutdown as tomcat as non-root user

  - by user53864

  How to start, shutdown and restart tomcat as non-root user. I have tomcat5.x installed on ubuntu machine(usr/share/tomcat). The tomcat directory has full permissions. When I shutdown(/usr/share/tomcat/bin/shudown.sh) or startup(/usr/share/tomcat/startup.sh) tomcat as normal user, it starts & shuts down normally as if it is executed as root user but I could not access webpage even after starting tomcat as non-root user. user1@station2:/usr/share/tomcat/webapps$ ../bin/shutdown.sh Using CATALINA_BASE: /usr/share/tomcat Using CATALINA_HOME: /usr/share/tomcat Using CATALINA_TMPDIR: /usr/share/tomcat/temp Using JRE_HOME: /usr 4 Oct, 2010 6:41:11 PM org.apache.catalina.startup.Catalina stopServer SEVERE: Catalina.stop: java.net.ConnectException: Connection refused at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.AbstractPlainSocketImpl.doConnect(AbstractPlainSocketImpl.java:310) at java.net.AbstractPlainSocketImpl.connectToAddress(AbstractPlainSocketImpl.java:176) at java.net.AbstractPlainSocketImpl.connect(AbstractPlainSocketImpl.java:163) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:384) at java.net.Socket.connect(Socket.java:546) at java.net.Socket.connect(Socket.java:495) at java.net.Socket.<init>(Socket.java:392) at java.net.Socket.<init>(Socket.java:206) at org.apache.catalina.startup.Catalina.stopServer(Catalina.java:421) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:616) at org.apache.catalina.startup.Bootstrap.stopServer(Bootstrap.java:337) at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:415)

  Read the article

• NFS confusion - writing many small files

  - by Antonis Christofides

  I have a Debian squeeze amd64 which is at the same time a NFS4 server and client (it mounts itself through NFS4). The local directory that leads directly to disk is /nfs4exports/mydir, whereas /nfs4mounts/mydir is the same thing mounted through NFS, using the machine's external IP address. Here is the line from fstab: 176.9.116.102:/mydir /nfs4mounts/mydir nfs4 soft 0 0 I have an application that writes many small files. If I write directly to /nfs4exports/mydir, it writes thousands of files per second; but if I write to /nfs4mounts/mydir, it writes 4 files per second or so. I can greatly increase speed if I add async to /etc/exports. (Writing a single large file to the NFS directory goes at more than 100 MB/s.) I am confused by the description of async in NFS. If my application accesses the local directory, system calls like write and close return even if caches have not been flushed to permanent storage. Apparently this is not true with NFS sync behaviour. However, with NFS async behaviour, even calls like fsync are ignored. Isn't it possible to work like local files, i.e. generally work asynchronously, but honour fsync and O_SYNC?

  Read the article

• How can I stop IIS7 (integrated mode) from reporting a 404 before I get a chance to handle it?

  - by Gary McGill

  I have an ASP.NET MVC 2 application running on IIS7 in integrated mode. I'm trying to do my own 404 handling, but IIS7 seems to be intercepting the error and returning its own 404 message to the client before I get a chance to handle it. I'm not having much luck coming at the problem from a programming perspective over on Stack Overflow, so I wondered if maybe it's a configuration problem. Is there something I have to do to tell IIS to let me handle my own errors? (I'm trying to use Application_Error in my global.asax but it's not even getting there). There is a custom error page defined (at the machine level, I think) for 404 but when I tried removing that it didn't really help - it simply showed a bald one-liner message instead. My code still didn't get a look in. Is it perhaps something to do with the routing? Maybe the "mysite.com/nosuchpage" URL isn't being routed to me and that's why I don't get a chance to intercept it? Do I need to do something so that ALL requests get routed through my app?

  Read the article

• Good visuals supporting adopting Macintosh in a Windows company

  - by jdmuys

  I work in a Windows only software service company, which just put up an internal contest for innovative ideas for the company. The idea I submitted is to let employees use a Mac instead of the mandatory PC if they wished to. My idea has been selected (among a few others) to reach the next stage of the contest. One of the items requested for the next stage is ONE visual that best illustrates the idea. While my pitch is rather good (I think), I have a hard time coming up with ONE visual that would be suggestive enough and not too fanboy-ish, or too restricted. That's why I am requesting suggestions. For reference, some of the points I intend to develop are (not in order): de facto safety (little or no malware) Apple as a company reached its leading position through innovation (bio)diversity is a source of value for a service company, that expands its reach. it makes financial sense the Mac is the most compatible machine, making it a lot easier to test our software (especially web sites). Some OS X technologies can be valuable to a software service company (eg Applescript) Some Apple tools can help us improve (eg Keynote) It's good citizenship for our company as Apple is now best in class according to Greenpeace. I realize this question may be out of topic here. I'd be happy to have suggestions on where to post this question. Please do not argue why OS X might be better or worse than Windows. My question is very narrow. Thanks.

  Read the article

< Previous Page | 865 866 867 868 869 870 871 872 873 874 875 876  | Next Page >