Search Results

Search found 17366 results on 695 pages for 'memory card'.

Page 89/695 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

  • Move an SSD with Windows 7 to a new PCIe SATA controller card

    - by Shevek
    This is my current setup: Abit AB9 QuadGT motherboard which has an Intel P965 chipset with Intel ICH8 SATA Rev. 2.0 controller Kingston HyperX 3K 120GB SSD which supports SATA Rev. 3.0 Windows 7 Ultimate x64 For some reason I was unable to install Windows with the controller set in AHCI mode, even with the correct driver from Intel so it is currently in IDE mode. Due to the ICH8 controller being SATA Rev 2.0 and running in IDE mode, the SSD is operating well under it's published read/write speeds. I have ordered an Asus U3S6 controller card to add both SATA Rev. 3.0 and USB 3.0 to my computer. The motherboard does have a PCIe x4 slot available so I will hopefully achieve the full potential of my SSD. My question is this - am I able to swap the SSD over to the controller card from the motherboard controller without having to clean install Windows? I am hoping that all I will need to do is ensure that the controller card drivers are available to Windows and set the registry as per this KB article. Will this work or should I perform a clean installation?

    Read the article

  • How to access the SD card through my Sony Ericsson Xperia Arc Phone?

    - by user16364
    I have a Sony Ericsson Xperia Arc phone and I cannot access its SD card through the USB cable provided. I have set the USB connection mode to MSC yet when I connect the phone to my computer I cannot see the SD card (or anything for that matter). The Disk Utility however, does see an SEMC Mass Storage device but it says that no media was detected. I have validated that the SD card works as I removed it from the camera and plugged it into a card reader and saw all the photos and files stored on it. I have validated that the phone works as I have connected it (in MSC mode) to my wife's Windows 7 computer. Can anyone please tell me how I can access the SD card on my phone.

    Read the article

  • How to access the SD card through my Sony Ericsson Xperia Arc Phone?

    - by user16364
    I have a Sony Ericsson Xperia Arc phone and I cannot access its SD card through the USB cable provided. I have set the USB connection mode to MSC yet when I connect the phone to my computer I cannot see the SD card (or anything for that matter). The Disk Utility however, does see an SEMC Mass Storage device but it says that no media was detected. I have validated that the SD card works as I removed it from the camera and plugged it into a card reader and saw all the photos and files stored on it. I have validated that the phone works as I have connected it (in MSC mode) to my wife's Windows 7 computer. Can anyone please tell me how I can access the SD card on my phone.

    Read the article

  • Two video card on one Mobo

    - by InfinityKing
    I recently purchased a new HP Pavilion p6-2265eo. It was then that I realised that it has only one DVI and one HDMI output.. I will connect my TV with the HDMI. so I am letft with only one DVI output. I need to have two monitors. Please help. Should I purchase a new video card and install it? My knowledge is limited. The specifications of my comp says that there is 1 x PCI-E x16, 3 x PCI-E x1. 1) I suppose that the video card already present in my purchase is connected on the PCI-E x16. Am I right? I dont want to open my desktop right now and check it for myself as it can void the warrenty. so I need an experienced person to tell me that. 2) I have an old nvidia geforce 7200 gt. Is it possible for me to connect it to my left over PCI-E x1? I searched for PCI-E x1 on the net and as far as I can understand the slot is too small for my old nvidia geforce 7200 gt graphic card. 3) what are the options? Please help this dummo :) Thankign you in advance,

    Read the article

  • Memory is full with vertex buffer

    - by Christian Frantz
    I'm having a pretty strange problem that I didn't think I'd run into. I was able to store a 50x50 grid in one vertex buffer finally, in hopes of better performance. Before I had each cube have an individual vertex buffer and with 4 50x50 grids, this slowed down my game tremendously. But it still ran. With 4 50x50 grids with my new code, that's only 4 vertex buffers. With the 4 vertex buffers, I get a memory error. When I load the game with 1 grid, it takes forever to load and with my previous version, it started up right away. So I don't know if I'm storing chunks wrong or what but it stumped me -.- for (int x = 0; x < 50; x++) { for (int z = 0; z < 50; z++) { for (int y = 0; y <= map[x, z]; y++) { SetUpVertices(); SetUpIndices(); cubes.Add(new Cube(device, new Vector3(x, map[x, z] - y, z), grass)); } } } vertexBuffer = new VertexBuffer(device, typeof(VertexPositionTexture), vertices.Count(), BufferUsage.WriteOnly); vertexBuffer.SetData<VertexPositionTexture>(vertices.ToArray()); indexBuffer = new IndexBuffer(device, typeof(short), indices.Count(), BufferUsage.WriteOnly); indexBuffer.SetData(indices.ToArray()); Thats how theyre stored. The array I'm reading from is a byte array which defines the coordinates of my map. Now with my old version, I used the same loading from an array so that hasn't changed. The only difference is the one vertex buffer instead of 2500 for a 50x50 grid. cubes is just a normal list that holds all my cubes for the vertex buffer. Another thing that just came to mind would be my draw calls. If I'm setting an effect for each cube in my cube list, that's probably going to take a lot of memory. How can I avoid doing this? I need the foreach method to set my cubes to the right position foreach (Cube block in cube.cubes) { effect.VertexColorEnabled = false; effect.TextureEnabled = true; Matrix center = Matrix.CreateTranslation(new Vector3(-0.5f, -0.5f, -0.5f)); Matrix scale = Matrix.CreateScale(1f); Matrix translate = Matrix.CreateTranslation(block.cubePosition); effect.World = center * scale * translate; effect.View = cam.view; effect.Projection = cam.proj; effect.FogEnabled = false; effect.FogColor = Color.CornflowerBlue.ToVector3(); effect.FogStart = 1.0f; effect.FogEnd = 50.0f; cube.Draw(effect); noc++; }

    Read the article

  • How to manage memory using classes in Objective-C?

    - by Flipper
    This is my first time creating an iPhone App and I am having difficulty with the memory management because I have never had to deal with it before. I have a UITableViewController and it all works fine until I try to scroll down in the simulator. It crashes saying that it cannot allocate that much memory. I have narrowed it down to where the crash is occurring: - (UITableViewCell *)tableView:(UITableView *)aTableView cellForRowAtIndexPath:(NSIndexPath *)indexPath { // Dequeue or create a cell UITableViewCellStyle style = UITableViewCellStyleDefault; UITableViewCell *cell = [aTableView dequeueReusableCellWithIdentifier:@"BaseCell"]; if (!cell) cell = [[[UITableViewCell alloc] initWithStyle:style reuseIdentifier:@"BaseCell"] autorelease]; NSString* crayon; // Retrieve the crayon and its color if (aTableView == self.tableView) { crayon = [[[self.sectionArray objectAtIndex:indexPath.section] objectAtIndex:indexPath.row] getName]; } else { crayon = [FILTEREDKEYS objectAtIndex:indexPath.row]; } cell.textLabel.text = crayon; if (![crayon hasPrefix:@"White"]) cell.textLabel.textColor = [self.crayonColors objectForKey:crayon]; else cell.textLabel.textColor = [UIColor blackColor]; return cell; } Here is the getName method: - (NSString*)getName { return name; } name is defined as: @property (nonatomic, retain) NSString *name; Now sectionArray is an NSMutableArray with instances of a class that I created Term in it. Term has a method getName that returns a NSString*. The problem seems to be the part of where crayon is being set and getName is being called. I have tried adding autorelease, release, and other stuff like that but that just causes the entire app to crash before even launching. Also if I do: cell.textLabel.text = @"test"; //crayon; /*if (![crayon hasPrefix:@"White"]) cell.textLabel.textColor = [self.crayonColors objectForKey:crayon]; else cell.textLabel.textColor = [UIColor blackColor];*/ Then I get no error whatsoever and it all scrolls just fine. Thanks in advance for the help! Edit: Here is the full Log of when I try to run the app and the error it gives when it crashes: [Session started at 2010-12-29 04:23:38 -0500.] [Session started at 2010-12-29 04:23:44 -0500.] GNU gdb 6.3.50-20050815 (Apple version gdb-967) (Tue Jul 14 02:11:58 UTC 2009) Copyright 2004 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "i386-apple-darwin".sharedlibrary apply-load-rules all Attaching to process 1429. gdb-i386-apple-darwin(1430,0x778720) malloc: * mmap(size=1420296192) failed (error code=12) error: can't allocate region ** set a breakpoint in malloc_error_break to debug gdb stack crawl at point of internal error: [ 0 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (align_down+0x0) [0x1222d8] [ 1 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (xstrvprintf+0x0) [0x12336c] [ 2 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (xmalloc+0x28) [0x12358f] [ 3 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (dyld_info_read_raw_data+0x50) [0x1659af] [ 4 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (dyld_info_read+0x1bc) [0x168a58] [ 5 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (macosx_dyld_update+0xbf) [0x168c9c] [ 6 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (macosx_solib_add+0x36b) [0x169fcc] [ 7 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (macosx_child_attach+0x478) [0x17dd11] [ 8 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (attach_command+0x5d) [0x64ec5] [ 9 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (mi_cmd_target_attach+0x4c) [0x15dbd] [ 10 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (captured_mi_execute_command+0x16d) [0x17427] [ 11 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (catch_exception+0x41) [0x7a99a] [ 12 ] /Developer/Platforms/iPhoneSimulator.platform/Developer/usr/libexec/gdb/gdb-i386-apple-darwin (mi_execute_command+0xa9) [0x16f63] /SourceCache/gdb/gdb-967/src/gdb/utils.c:1144: internal-error: virtual memory exhausted: can't allocate 1420296192 bytes. A problem internal to GDB has been detected, further debugging may prove unreliable. The Debugger has exited with status 1.The Debugger has exited with status 1. Here is the backtrace that I get when I set the breakpoint for malloc_error_break: #0 0x0097a68c in objc_msgSend () #1 0x01785bef in -[UILabel setText:] () #2 0x000030e0 in -[TableViewController tableView:cellForRowAtIndexPath:] (self=0x421d760, _cmd=0x29cfad8, aTableView=0x4819600, indexPath=0x42190f0) at /Volumes/Main2/Enayet/TableViewController.m:99 #3 0x016cee0c in -[UITableView(UITableViewInternal) _createPreparedCellForGlobalRow:withIndexPath:] () #4 0x016c6a43 in -[UITableView(UITableViewInternal) _createPreparedCellForGlobalRow:] () #5 0x016d954f in -[UITableView(_UITableViewPrivate) _updateVisibleCellsNow] () #6 0x016d08ff in -[UITableView layoutSubviews] () #7 0x03e672b0 in -[CALayer layoutSublayers] () #8 0x03e6706f in CALayerLayoutIfNeeded () #9 0x03e668c6 in CA::Context::commit_transaction () #10 0x03e6653a in CA::Transaction::commit () #11 0x03e6e838 in CA::Transaction::observer_callback () #12 0x00b00252 in __CFRunLoopDoObservers () #13 0x00aff65f in CFRunLoopRunSpecific () #14 0x00afec48 in CFRunLoopRunInMode () #15 0x00156615 in GSEventRunModal () #16 0x001566da in GSEventRun () #17 0x01689faf in UIApplicationMain () #18 0x00002398 in main (argc=1, argv=0xbfffefb0) at /Volumes/Main2/Enayet/main.m:14

    Read the article

  • Using WeakReference to resolve issue with .NET unregistered event handlers causing memory leaks.

    - by Eric
    The problem: Registered event handlers create a reference from the event to the event handler's instance. If that instance fails to unregister the event handler (via Dispose, presumably), then the instance memory will not be freed by the garbage collector. Example: class Foo { public event Action AnEvent; public void DoEvent() { if (AnEvent != null) AnEvent(); } } class Bar { public Bar(Foo l) { l.AnEvent += l_AnEvent; } void l_AnEvent() { } } If I instantiate a Foo, and pass this to a new Bar constructor, then let go of the Bar object, it will not be freed by the garbage collector because of the AnEvent registration. I consider this a memory leak, and seems just like my old C++ days. I can, of course, make Bar IDisposable, unregister the event in the Dispose() method, and make sure to call Dispose() on instances of it, but why should I have to do this? I first question why events are implemented with strong references? Why not use weak references? An event is used to abstractly notify an object of changes in another object. It seems to me that if the event handler's instance is no longer in use (i.e., there are no non-event references to the object), then any events that it is registered with should automatically be unregistered. What am I missing? I have looked at WeakEventManager. Wow, what a pain. Not only is it very difficult to use, but its documentation is inadequate (see http://msdn.microsoft.com/en-us/library/system.windows.weakeventmanager.aspx -- noticing the "Notes to Inheritors" section that has 6 vaguely described bullets). I have seen other discussions in various places, but nothing I felt I could use. I propose a simpler solution based on WeakReference, as described here. My question is: Does this not meet the requirements with significantly less complexity? To use the solution, the above code is modified as follows: class Foo { public WeakReferenceEvent AnEvent = new WeakReferenceEvent(); internal void DoEvent() { AnEvent.Invoke(); } } class Bar { public Bar(Foo l) { l.AnEvent += l_AnEvent; } void l_AnEvent() { } } Notice two things: 1. The Foo class is modified in two ways: The event is replaced with an instance of WeakReferenceEvent, shown below; and the invocation of the event is changed. 2. The Bar class is UNCHANGED. No need to subclass WeakEventManager, implement IWeakEventListener, etc. OK, so on to the implementation of WeakReferenceEvent. This is shown here. Note that it uses the generic WeakReference that I borrowed from here: http://damieng.com/blog/2006/08/01/implementingweakreferencet I had to add Equals() and GetHashCode() to his class, which I include below for reference. class WeakReferenceEvent { public static WeakReferenceEvent operator +(WeakReferenceEvent wre, Action handler) { wre._delegates.Add(new WeakReference<Action>(handler)); return wre; } public static WeakReferenceEvent operator -(WeakReferenceEvent wre, Action handler) { foreach (var del in wre._delegates) if (del.Target == handler) { wre._delegates.Remove(del); return wre; } return wre; } HashSet<WeakReference<Action>> _delegates = new HashSet<WeakReference<Action>>(); internal void Invoke() { HashSet<WeakReference<Action>> toRemove = null; foreach (var del in _delegates) { if (del.IsAlive) del.Target(); else { if (toRemove == null) toRemove = new HashSet<WeakReference<Action>>(); toRemove.Add(del); } } if (toRemove != null) foreach (var del in toRemove) _delegates.Remove(del); } } public class WeakReference<T> : IDisposable { private GCHandle handle; private bool trackResurrection; public WeakReference(T target) : this(target, false) { } public WeakReference(T target, bool trackResurrection) { this.trackResurrection = trackResurrection; this.Target = target; } ~WeakReference() { Dispose(); } public void Dispose() { handle.Free(); GC.SuppressFinalize(this); } public virtual bool IsAlive { get { return (handle.Target != null); } } public virtual bool TrackResurrection { get { return this.trackResurrection; } } public virtual T Target { get { object o = handle.Target; if ((o == null) || (!(o is T))) return default(T); else return (T)o; } set { handle = GCHandle.Alloc(value, this.trackResurrection ? GCHandleType.WeakTrackResurrection : GCHandleType.Weak); } } public override bool Equals(object obj) { var other = obj as WeakReference<T>; return other != null && Target.Equals(other.Target); } public override int GetHashCode() { return Target.GetHashCode(); } } It's functionality is trivial. I override operator + and - to get the += and -= syntactic sugar matching events. These create WeakReferences to the Action delegate. This allows the garbage collector to free the event target object (Bar in this example) when nobody else is holding on to it. In the Invoke() method, simply run through the weak references and call their Target Action. If any dead (i.e., garbage collected) references are found, remove them from the list. Of course, this only works with delegates of type Action. I tried making this generic, but ran into the missing where T : delegate in C#! As an alternative, simply modify class WeakReferenceEvent to be a WeakReferenceEvent, and replace the Action with Action. Fix the compiler errors and you have a class that can be used like so: class Foo { public WeakReferenceEvent<int> AnEvent = new WeakReferenceEvent<int>(); internal void DoEvent() { AnEvent.Invoke(5); } } Hopefully this will help someone else when they run into the mystery .NET event memory leak!

    Read the article

  • SLI Video Cards

    - by Scott
    I'm configuring a new desktop. I'm looking through all PCI Express 2.0 x16 video cards on NewEgg at the moment. All cards seem to be stating that they have SLI Support or CrossFireX support. I know that these 2 technologies enable you to connect more than one video card together to create more of a powerful video experience. These cards that have this support seem to be more expensive that other cards though. When I did a NewEgg search for cards that did NOT have these two supports, no matches came up for PCI Express 2.0 x16 (haven't checked other interfaces yet though). Can you run an SLI/CrossFireX card as a single card (and if you can is it efficient or even good?), or do you need to have more than one card to run them? Also, do they make cards without these two technologies anymore, and are they even cheaper at this point? I really have no need for SLI/CrossFireX at all, so I was wondering what I should look into. Do cards without this technology not run on the PCI Express 2.0 x16 interface? Thanks ahead of time for all your help.

    Read the article

  • SLI Video Cards

    - by Scott
    I'm configuring a new desktop. I'm looking through all PCI Express 2.0 x16 video cards on NewEgg at the moment. All cards seem to be stating that they have SLI Support or CrossFireX support. I know that these 2 technologies enable you to connect more than one video card together to create more of a powerful video experience. These cards that have this support seem to be more expensive that other cards though. When I did a NewEgg search for cards that did NOT have these two supports, no matches came up for PCI Express 2.0 x16 (haven't checked other interfaces yet though). Can you run an SLI/CrossFireX card as a single card (and if you can is it efficient or even good?), or do you need to have more than one card to run them? Also, do they make cards without these two technologies anymore, and are they even cheaper at this point? I really have no need for SLI/CrossFireX at all, so I was wondering what I should look into. Do cards without this technology not run on the PCI Express 2.0 x16 interface? Thanks ahead of time for all your help.

    Read the article

  • Why is my second monitor not working?

    - by StampedeXV
    Since I have my new computer, I have a very weird problem. Facts: New Computer: Motherboard: ASRock Z77 Pro 3 Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i5-3570 Windows 7 64bit 500W beQuiet special edition (92% efficiency) 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 2 2 magnetic HDDs + 1 SDD 1 DVD-R Old Computer: Motherboard: Asus P55 something Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i7-870 Windows 7 64bit 550W Corsair 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 3 2 magnetic HDDs + 1 SDD 1 DVD-R On the old computer it worked fine with two monitors. Moving to the new (I took the same Graphics-card) it only works with one. The weird thing I mentioned is: not matter which one. But if I put both there, only one is available. There is no reaction at the start (where normally (at least if I remember correctly) the monitor shortly went from "standby" to "on"). Windows does not recognize a second monitor in the Device Manager. I have the latest drivers for Motherboard and Graphics-card. I have the latest BIOS drivers. I am out of ideas. Edit: completed computer setup

    Read the article

  • Managing Instances in Python

    - by BeensTheGreat
    Hello, I am new to Python and this is my first time asking a stackOverflow question, but a long time reader. I am working on a simple card based game but am having trouble managing instances of my Hand class. If you look below you can see that the hand class is a simple container for cards(which are just int values) and each Player class contains a hand class. However, whenever I create multiple instances of my Player class they all seem to manipulate a single instance of the Hand class. From my experience in C and Java it seems that I am somehow making my Hand class static. If anyone could help with this problem I would appreciate it greatly. Thank you, Thad To clarify: An example of this situation would be p = player.Player() p1 = player.Player() p.recieveCard(15) p1.recieveCard(21) p.viewHand() which would result in: [15,21] even though only one card was added to p Hand class: class Hand: index = 0 cards = [] #Collections of cards #Constructor def __init__(self): self.index self.cards def addCard(self, card): """Adds a card to current hand""" self.cards.append(card) return card def discardCard(self, card): """Discards a card from current hand""" self.cards.remove(card) return card def viewCards(self): """Returns a collection of cards""" return self.cards def fold(self): """Folds the current hand""" temp = self.cards self.cards = [] return temp Player Class import hand class Player: name = "" position = 0 chips = 0 dealer = 0 pHand = [] def __init__ (self, nm, pos, buyIn, deal): self.name = nm self.position = pos self.chips = buyIn self.dealer = deal self.pHand = hand.Hand() return def recieveCard(self, card): """Recieve card from the dealer""" self.pHand.addCard(card) return card def discardCard(self, card): """Throw away a card""" self.pHand.discardCard(card) return card def viewHand(self): """View the players hand""" return self.pHand.viewCards() def getChips(self): """Get the number of chips the player currently holds""" return self.chips def setChips(self, chip): """Sets the number of chips the player holds""" self.chips = chip return def makeDealer(self): """Makes this player the dealer""" self.dealer = 1 return def notDealer(self): """Makes this player not the dealer""" self.dealer = 0 return def isDealer(self): """Returns flag wether this player is the dealer""" return self.dealer def getPosition(self): """Returns position of the player""" return self.position def getName(self): """Returns name of the player""" return self.name

    Read the article

  • Not enough physical memory available to run Virtual Machine

    - by unknown (google)
    hi I when i am trying to run virtual machine on VMW 6.5 it shows me following error. "Not enough physical memory is available to power on this virtual machine with its configured settings. To fix this problem, adjust the additional memory settings to allow more virtual machine memory to be swapped. If you were able to power on this virtual machine on this host computer in the past, try rebooting the host computer. Rebooting may allow you to use slightly more host memory to run virtual machines." i have also tried options that are suggested from above error, but still its not working. Can you help me to solve this problem? Thanks

    Read the article

  • Bank Interleave Requested but not enabled

    - by wbeard52
    I have a ECS A770M-A motherboard with a 2.2GHz Phenom 64 Quad Core processor with 4 gigs of ram. I also have a 1GB DDR3 Zotac GeForce 9500GT video card installed in the computer. I believe the main memory is DDR2. The problem I am having is that I get a "Bank Interleave Requested but not Enabled" error on startup. The computer boots up fine (no error) with the 4gigs of ram if I replace the video card with the previous 256MB video card. I have also tried placing a single gig of ram in the computer with the Zotac video card and still get the error. My question is what would typically cause this error and would a DDR3 video ram be compatible with DDR2 system ram? Thanks

    Read the article

  • Using a 64bit Linux kernel, can't see more than 4GB of RAM in /proc/meminfo

    - by Chris Huang-Leaver
    I'm running my new computer which has 8GB of RAM installed, which is visable from BIOS page, does not show in /proc/meminfo uname -a Linux localhost 3.0.6-gentoo #2 SMP PREEMPT Sat Nov 19 10:45:22 GMT-- x86_64 AMD Phenom(tm) II X4 955 Processor AuthenticAMD GNU/Linux The result of /proc/meminfo is as follows: (thans Andrey) MemTotal: 4021348 kB MemFree: 1440280 kB Buffers: 23696 kB Cached: 1710828 kB SwapCached: 4956 kB Active: 1389904 kB Inactive: 841364 kB Active(anon): 1337812 kB Inactive(anon): 714060 kB Active(file): 52092 kB Inactive(file): 127304 kB Unevictable: 32 kB Mlocked: 32 kB SwapTotal: 8388604 kB SwapFree: 8047900 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 492732 kB Mapped: 47528 kB Shmem: 1555120 kB Slab: 267724 kB SReclaimable: 177464 kB SUnreclaim: 90260 kB KernelStack: 1176 kB PageTables: 12148 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 10399276 kB Committed_AS: 3293896 kB VmallocTotal: 34359738367 kB VmallocUsed: 317008 kB VmallocChunk: 34359398908 kB AnonHugePages: 120832 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 23552 kB DirectMap2M: 3088384 kB DirectMap1G: 1048576 kB I have tried using mem=8G as a kernel boot parameter, I read a post about setting HIGHMEM64G to yes, before realising that only applies to 32bit kernels. Trying dmindecode -t memory SMBIOS 2.7 present. Handle 0x0026, DMI type 16, 23 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Multi-bit ECC Maximum Capacity: 32 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0028, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM0 Bank Locator: BANK0 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer0 Serial Number: SerNum0 Asset Tag: AssetTagNum0 Part Number: Array1_PartNumber0 Rank: Unknown Handle 0x002A, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM1 Bank Locator: BANK1 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer1 Serial Number: SerNum1 Asset Tag: AssetTagNum1 Part Number: Array1_PartNumber1 Rank: Unknown Handle 0x002C, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM2 Bank Locator: BANK2 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer2 Serial Number: SerNum2 Asset Tag: AssetTagNum2 Part Number: Array1_PartNumber2 Rank: Unknown Handle 0x002E, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM3 Bank Locator: BANK3 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer3 Serial Number: SerNum3 Asset Tag: AssetTagNum3 Part Number: Array1_PartNumber3 Rank: Unknown

    Read the article

  • Page pool memory

    - by legiwei
    I'm currently using Windows XP SP3 32 bit, using C2D E6320 with 2GB RAM. When I am playing Starcraft 2, I encounter an error where it says my system is running low on page pool memory. Starcraft graphic settings suggested a high settings for me. I do not think it has to do with my GC but with my RAM. I then made a search to try to rectify the problem. Apparently, it's something to do with my virtual memory. I then proceed to try to the suggested solution which is to temper the registry and limit the page pool memory to 384MB. However, having done so, I still could not achieved it. I've seen screenshot settings of windows XP with 2GB having 384MB of page pool memory. My default settings puts it at 195MB whereas when I try to increase the pool limit, it can only go to a max of 229MB. I tried increasing my RAM capacity to 3GB but the pool limit still remains. I like to know how to increase my page pool memory. I've tried searching for solution but to no avail other than the one that I've mentioned above (which didn't solve my problem completely).

    Read the article

  • Help with memory usage issues on VPS

    - by Niall Collins
    Hi there, I am running a VPS server with 6 .net web sites/applications running on it. I am having issues with performance on the server, mainly it running out of memory. I contacted the company that lease the server to me and they told me it was because I also had sql server 2008 express also running on the server. So I went ahead and removed this, uninstalled etc. However I still seem to be having issues. For example at present, looking at resource consumption, the virtual memory is: ID: vprvmem Current Use: 894,328,832 bytes Limit: 1,073,741,824 bytes This means useage of ~80%. Is there any way I can check out exactly that applications, web sites, software is taking up most of the servers memory, so I can look at rectifying it. I feel that 80% is much to high to allow for contingency for a spike in traffic. I have got extra memory resources added to the box recently, but I would prefer finding the source of the problem rather than throwing extra memory at it. Maybe these levels are correct and alls running ok, but would like to investigate it to make sure. My knowledge of hardware is limited as I mostly deal in the spectrum of software. So any tools out there that can help me or any pertient advice.

    Read the article

  • Convert RAID-0 to RAID-1 on HP ML350G6 with P410i zero memory

    - by JLe
    I have an HP ML350 G6 with a P410i zero memory RAID controller. As far as I can understand that means I can't expand a current single drive "RAID-0" configuration to a RAID-1 using the HP Offline ACU without installing memory and BBWC. Is that correct? What makes me think about this is the fact that expanding RAID-0 to RAID-1 should be pretty similar to replacing a failed drive in an already existing RAID-1? So then why can't I expand without memory and BBWC? Is my best option otherwise to (i) use Ghost to capture the disk, create a new RAID-1 with the existing drive and a new one or (ii) buy memory+BBWC and do it online? Thanks

    Read the article

  • IIS Application Pool Memory Size Problem

    - by Roni
    I increased my application pool memory size from default to 500 mb. and i have IIS 7.5. My server sometimes falling down (service unavailable) and i don't know the reason. I did couple of changes at the same day that i changed memory size in iis and from that days i am getting this problem in one of my servers. Is there anybody can tell me what is the right way to increase memory and what can be the problems???? Thankss Roni

    Read the article

  • How does azure memory usage work?

    - by Jed Grant
    I have a windows azure website. In the dashboard it shows me that I have used 1.51 GB of the 2GB available per hour. I keep increasing the number of instances available in the shared node so the site doesn't shut down. After each hour finishes, the memory usage still shows 1.51 GB used. I assume this would start at ZERO and then be used as time goes on, but that doesn't appear to be the case. How does server memory work? What are some reasons my application using this much memory? (I use no output caching and generally have just built off of the basic MVC templates provided in visual studio.) What other considerations should I be making to get the amount of memory needed to decrease?

    Read the article

  • Server memory issues, and expected level of service from hosting company

    - by Greg
    I'm involved in maintaining an Ubuntu VPS which runs our django websites (nginx/apache/mod_wsgi) and we've been having some memory spikes which have either caused the database to die, or induced kernel panic when the memory management system can't find any killable processes. I'm working on fixing the memory spikes, but I'm wondering whether there's anything I can do to better deal with the problem if it occurs again. Are there any tools I could use to detect the memory spikes and then, say, kill the offending process and email the server admin to fix it up? Killing off one website so that the server can remain operational is certainly preferable to the whole thing falling over. Also, we were charged $600 for after-hours service because we had to get the hosting company to restart the server - is this standard practice among hosting companies? Another provider I work with provides a panel with which I can stop and start the server myself, and given that a restart was all that was needed, $600 seems mightily excessive. (That's NZD, it's around $445 USD)

    Read the article

  • Understanding ESXi and Memory Usage

    - by John
    Hi, I am currently testing VMWare ESXi on a test machine. My host machine has 4gigs of ram. I have three guests and each is assigned a memory limit of 1 GB (and only 512 MB reserved). The host summary screen shows a memory capacity of 4082.55 MB and a usage of 2828 MB with two guests running. This seems to make sense, two gigs for each VM plus an overhead for the host. 800MB seems high but that is still reasonable. But on the Resource Allocation Screen I see a memory capacity of 2356 MB and an available capacity of 596 MB. Under the configuration tab, memory link I see a physical total of 4082.5 MB, System of 531.5 MB and VM of 3551.0 MB. I have only allocated my VMs for a gig each, and with two VMs running they are taking up almost two times the amount of ram allocated. Why is this, and why does the Resource Allocation screen short change me so much?

    Read the article

  • Separation of memory oriented process and CPU oriented process

    - by Jeevan Dongre
    I am develops guy working for an e-commerce company I am running my e-commerce application built using ruby on rails spree commerce. I am presently running 2 medium instances in the production. One is a high memory instance which has 3.8 RAM and single Core CPU and another one is high CPU instance which has Dual Core CPU. Basically AWS calls it has m1.medium and c1.medium instance respectively. My question is it possible to separate the processes according the cpu intense and memory intense? So that all the cpu intense process can be made run in high cpu instance and all the memory intense process can be made to run in the high memory instances. Is any tool available to identify those process. Kindly give me some heads up. Thank you

    Read the article

  • Page pool memory

    - by legiwei
    I'm currently using Windows XP SP3 32 bit, using C2D E6320 with 2GB RAM. When I am playing Starcraft 2, I encounter an error where it says my system is running low on page pool memory. Starcraft graphic settings suggested a high settings for me. I do not think it has to do with my GC but with my RAM. I then made a search to try to rectify the problem. Apparently, it's something to do with my virtual memory. I then proceed to try to the suggested solution which is to temper the registry and limit the page pool memory to 384MB. However, having done so, I still could not achieved it. I've seen screenshot settings of windows XP with 2GB having 384MB of page pool memory. My default settings puts it at 195MB whereas when I try to increase the pool limit, it can only go to a max of 229MB. I tried increasing my RAM capacity to 3GB but the pool limit still remains. I like to know how to increase my page pool memory. I've tried searching for solution but to no avail other than the one that I've mentioned above (which didn't solve my problem completely).

    Read the article

  • Increase in Virtual Memory [closed]

    - by Philly
    If we increase the virtual memory of windows server 2008 will it improve the performance on the application. upto what size can we increase the virtual memory in 32bit server. What are disadvantages and advantages of it? we are running bulk jobs(all imports and exports) everyday at 3pm.. because of that we are getting some system out of memory exceptions and and application is going down. Any suggestions. Thanks

    Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >