information visualization - Page 900

HP ProLiant DL380 G3 Running Windows Server 2000 has crashed between 6-7:30am for the past 5 days

- by user109717

I have a HP ProLiant DL380 G3 running Windows Server 2000 that has been crashing everyday between 6-730am. This started when I changed out a failing hard drive 6 days ago. I have looked at the scheduled tasks which does not have anything pertaining to this issue. Below are the only things I see in the system log and some of the dump files. Can this be a hardware issue if this happens at a certain time frame everyday? Any help is greatly appreciated. Thanks The previous system shutdown at 6:07:55 AM on 2/7/2012 was unexpected. System Information Agent: Health: The server is operational again. The server has previously been shutdown by the Automatic Server Recovery (ASR) feature and has just become operational again. [SNMP TRAP: 6025 in CPQHLTH.MIB] BugCheck 7A, {3, c0000005, 3400028, 0} Probably caused by : memory_corruption ( nt!MiMakeSystemAddressValidPfn+42 ) Followup: MachineOwner 0: kd !analyze -v * Bugcheck Analysis * * KERNEL_DATA_INPAGE_ERROR (7a) The requested page of kernel data could not be read in. Typically caused by a bad block in the paging file or disk controller error. Also see KERNEL_STACK_INPAGE_ERROR. If the error status is 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185, it means the disk subsystem has experienced a failure. If the error status is 0xC000009A, then it means the request failed because a filesystem failed to make forward progress. Arguments: Arg1: 00000003, lock type that was held (value 1,2,3, or PTE address) Arg2: c0000005, error status (normally i/o status code) Arg3: 03400028, current process (virtual address for lock type 3, or PTE) Arg4: 00000000, virtual address that could not be in-paged (or PTE contents if arg1 is a PTE address) MODULE_NAME: nt IMAGE_NAME: memory_corruption BugCheck A, {0, 2, 1, 804137d6} Probably caused by : ntkrnlmp.exe ( nt!CcGetVirtualAddress+ba ) * Bugcheck Analysis * * IRQL_NOT_LESS_OR_EQUAL (a) An attempt was made to access a pageable (or completely invalid) address at an interrupt request level (IRQL) that is too high. This is usually caused by drivers using improper addresses. If a kernel debugger is available get the stack backtrace. Arguments: Arg1: 00000000, memory referenced Arg2: 00000002, IRQL Arg3: 00000001, bitfield : bit 0 : value 0 = read operation, 1 = write operation bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status) Arg4: 804137d6, address which referenced memory MODULE_NAME: nt IMAGE_NAME: ntkrnlmp.exe

Read the article

Asterisk: Dropping calls with an "ast_yyerror"

- by Nick

I'm having an intermittent issue where asterisk will play our greeting to the caller, and then drop the call instead of making our phones ring. I'm unable to reproduce the problem with any phones I have here, and many callers get through just fine. Some callers though, run into the problem, and I can't find any pattern to it. The bit of information I could find said it was caused by an error in evaluating a dialplan expression. I'm thinking it's this line: exten = START,n,GotoIf($[${FORCE_CLOSED}=TRUE]?CLOSED,1) But I'm not sure what's wrong with it. I see the following error on the console: [Apr 4 16:29:49] WARNING[27038]: ast_expr2.fl:459 ast_yyerror: ast_yyerror(): syntax error: syntax error, unexpected '=', expecting $end; Input:=TRUE^ Surrounding Console output: -- Executing [START@AGInbound:1] Answer("IAX2/AtlantaTeliax-10086", "") in new stack -- Executing [START@AGInbound:2] BackGround("IAX2/AtlantaTeliax-10086", 0000_AG_THANK_YOU_FOR_CALLING_AG") in new stack -- Playing '0000_AG_THANK_YOU_FOR_CALLING_AG.slin' (language 'en') [Apr 4 16:29:49] WARNING[27038]: ast_expr2.fl:459 ast_yyerror: ast_yyerror(): syntax error: syntax error, unexpected '=', expecting $end; Input: =TRUE ^ [Apr 4 16:29:49] WARNING[27038]: ast_expr2.fl:463 ast_yyerror: If you have questions, please refer to doc/tex/channelvariables.tex in the asterisk source. -- Executing [START@AGInbound:3] GotoIf("IAX2/AtlantaTeliax-10086", "?CLOSED,1") in new stack -- Executing [START@AGInbound:4] GotoIfTime("IAX2/AtlantaTeliax-10086", "9:30-17:0|mon-fri|*|*?OPEN,1") in new stack -- Executing [START@AGInbound:5] GotoIfTime("IAX2/AtlantaTeliax-10086", "10:0-18:30|sat|*|*?OPEN,1") in new stack -- Executing [START@AGInbound:6] GotoIfTime("IAX2/AtlantaTeliax-10086", "12:0-17:0|sun|*|*?OPEN,1") in new stack Relevant lines from the dial plan: exten = START,1,Answer() exten = START,n,Background(0000_AG_THANK_YOU_FOR_CALLING_AG) ; See if we're open ; Force Closed if no one's going to be answering exten = START,n,GotoIf($[${FORCE_CLOSED}=TRUE]?CLOSED,1) exten = START,n,GotoIfTime(${AG_WEEKDAY_OPEN_HOUR}:${AG_WEEKDAY_OPEN_MIN}-${AG$ exten = START,n,GotoIfTime(${AG_SATURDAY_OPEN_HOUR}:${AG_SATURDAY_OPEN_MIN}-${$ exten = START,n,GotoIfTime(${AG_SUNDAY_OPEN_HOUR}:${AG_SUNDAY_OPEN_MIN}-${AG_S$ ; ...and we're not. But maybe the time of day has been overridden? exten = START,n,GotoIf($[${OVERRIDE_TIME_OF_DAY}=TRUE]?OPEN,1) ; No override... We're definatly closed. exten = START,n,Goto(CLOSED,1) Any idea what's wrong with the expression? We recently upgraded from 1.4 to 1.6.

Read the article

Migrating Split Access Database from one domain to another (not working, details in Q)

- by Expo_Rob

Some background: I'm a programmer, not a network administrator, who has been asked to migrate some accounting software (Integrated Office Accounting version 3.2) from an existing domain (OLD_NETWORK) to a new domain (NEW_NETWORK). No-body at the office knows how it works under the hood. It is a split Access 2000 database with the back-end shared and on a file server (which is also the DC) using mapped drives. The DC is NT Server 4 SP 6. The new server is server 2003. The two networks are running independently (ie: two computers on each desk). I have been able to get new computers set up on NEW_NETWORK and working with the IOA software just perfectly but for one problem: The company here uses other entirely separate databases which access the tables IOA maintains (specifically the 'customers' table) via links. To switch between these systems, you press F11 then File-Open the appropriate database and away you go (this is necessary to maintain the permissions that the IOA system uses to protect the customers table). The entire database is Access 2000, the links go to other Access databases, SQL-Server is not involved in any way, nor is a migration to SQL server likely. If I can't migrate anything over, everything will stay as it is, and the NEW_NETWORK computers will not be used. The problem: When I try and update these seperate databases (I shall call one "BANK_ACCOUNT", but the name does not matter), it says "this recordset cannot be updated". It also will sometimes not pull information out of the 'customers' table (ie: date_entered) when looking at a report of everyone who opened a bank account on a certain day (ie: today). I have tried: Giving 'everyone' full control via. shared directory permissions Giving 'everyone' full control on a file system level Checking the permissions within Access (everyone has full read/write on all tables) Copying the entire server contents from one file server to another (ie: xcopy everything) Copying the entire local client files from one computer to another, putting them in the exact same position in the file system, with the same permissons (or full control to 'everyone'). Running as an Administrator Taking one of the NEW_NETWORK computers, having it join OLD_NETWORK and run the software (direct copy from a working system with identical drive mappings), this did not work Weeping openly My Question: Is there anything else I can try? (sorry for this being so long)

Read the article

Google Rules for Retail

- by David Dorf

In the book What Would Google Do?, Jeff Jarvis outlines ten "Google Rules" that define how Google acts. These rules help define how Web 2.0 businesses operate today and into the future. While there's a chapter in the book on applying these rules to the retail industry, it wasn't very in-depth. So I've decided to more directly apply the rules to retail, along with some notable examples of success. The table below shows Jeff's Google Rule, some Industry Examples, and New Retailer Rules that I created. Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} table.MsoTableGrid {mso-style-name:"Table Grid"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-priority:59; mso-style-unhide:no; border:solid black 1.0pt; mso-border-themecolor:text1; mso-border-alt:solid black .5pt; mso-border-themecolor:text1; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-border-insideh:.5pt solid black; mso-border-insideh-themecolor:text1; mso-border-insidev:.5pt solid black; mso-border-insidev-themecolor:text1; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} Google Rule Industry Examples New Retailer Rule New Relationship Your worst customer is your friend; you best customer is your partner Newegg.com lets manufacturers respond to customer comments that are critical of the product, and their EggXpert site lets customers help other customers. Listen to what your customers are saying about you. Convert the critics to fans and the fans to influencers. New Architecture Join a network; be a platform Tesco and BestBuy released APIs for their product catalogs so third-parties could create new applications. Become a destination for information. New Publicness Life is public, so is business Zappos and WholeFoods founders are prolific tweeters/bloggers, sharing their opinions and connecting to customers. It's not always pretty, but it's genuine. Be transparent. Share both your successes and failures with your customers. New Society Elegant organization Wet Seal helps their customers assemble outfits and show them off to each other. Barnes & Noble has a community site that includes a bookclub. Communities of your customers already exist, so help them organize better. New Economy Mass market is dead; long live the mass of niches lululemon found a niche for yoga inspired athletic wear. Threadless uses crowd-sourcing to design short-runs of T-shirts. Serve small markets with niche products. New Business Reality Decide what business you're in When Lowes realized catering to women brought the men along, their sales increased. Customers want experiences to go with the products they buy. New Attitude Trust the people and listen In 2008 Starbucks launched MyStartbucksIdea to solicit ideas from their customers. Use social networks as additional data points for making better merchandising decisions. New Ethic Be honest and transparent; don't be evil Target is giving away reusable shopping bags for Earth Day. Kohl's has outfitted 67 stores with solar arrays. Being green earns customers' respect and lowers costs too. New Speed Life is live H&M and Zara keep up with fashion trends. Be prepared to pounce on you customers' fickle interests. New Imperatives Encourage, enable and protect innovation 1-800-Flowers was the first do sales in Facebook and an early adopter of mobile commerce. The Sears Personal Shopper mobile app finds products based on a photo. Give your staff permission to fail so innovation won't be stifled. Jeff will be a keynote speaker at Crosstalk, our upcoming annual user conference, so I'm looking forward to hearing more of his perspective on retail and the new economy.

Read the article

Aggregate SharePoint Event/Items into your Calendar view using Calendar Overlay

- by eJugnoo

One of the most common features I have seen in common use for SharePoint (prior to 2010) in Intranet environments for Team site is Calendar’s. Not only the Calendar list type, but also the ability to add a Calendar view to any list that has the desired columns to construct a Calendar – such as Start, End, Title etc. While this was all great for a single site/calendar, the problem of having to track numerous calendar’s remained. With introduction of Outlook 2007 bi-directional integration with SharePoint, and particularly the ability of Outlook to overlay calendar helped bridge the gap. Now one could connect to number of team sites, and setup Calendar overlays in Outlook using varying colours, to easily identify event source and yet benefit from the plotting of events on single Calendar view. This was all good, but each user in your Enterprise was supposed to setup in a “pull” fashion. This is good for flexibility, not so good when you need to “push” consistency and productivity (re-use). So, what was missing on SharePoint is the ability to have server-side overlay’s that everyone can see – in a single place, aggregating multiple sources. Until SharePoint 2010 arrived! Calendars Overlay in SharePoint 2010 There are Calendar lists and Calendar views. View can be created for almost all lists, as far as you have desired column’s in a list like Start, End, Title etc. to be able to describe and plot an item in a Calendar format. In SharePoint 2010, create a new Calendar list. Go to Calendar ribbon tab, and click Calendar Overlay. You get the screen with list of existing Overlay’s associated with current Calendar (list – in our case). Click on “New Calendar”… Notice the breadcrumb! You are adding Overlay to existing list (Team Calendar – in our case). You have choice of “pulling” Calendar info from an existing Calendar (list/view) in SharePoint or even from Exchange! Set standard info like a name, description and decide the colour you want for the items in aggregated Calendar overlay. Select the source site/list/view, anywhere in farm. When you select Exchange as source of Calendar, you get option to add OWA and Exchange Web Service url. I will cover details of connecting with Exchange in another post, and focus on Overlay’s with SharePoint for this one. Once you have added a new Calendar overlay to existing Calendar veiw, you get something like below for Day view, Week view, and Month view respectively Notice the Overlay colours: Now, if you decide to connect this Calendar to Outlook to sync the items, it will only sync items from main view, and not from Overlay source. So such Overlay of calendar’s is server-side aggregation only. That increases my curiosity, so I try adding the Calendar list view as a web-part on a new page. As you see, this instance of view didn’t include item from source that we had added to default Calendar view. This is – probably – due to the fact that this is a new web-part view for the page. If you want to add overlay to this one, you have to redo that from Ribbon. This also means, subject to purpose and context you get the flexibility to decide what overlay is suited. Also you can only add 10 Overlay’s to an existing view instance. Conclusion Calendar Overlay is clearly a very useful feature that fills a gap of not being able to aggregate information from multiple sources into a Calendar view within context of current items. Source of items can be existing SharePoint calendar views on any site, or even Exchange (via OWA/Exchange web services). List type for source doesn’t matter, it just need a Calendar view type available. You can have 10 overlays. Overlays are for the specific view only, and are server-side only – which means they do not get synced in Outlook. While you can drag-drop current list items, you cannot edit overlay items as they are read-only within scope of current Calendar view. You can of course click on source Overlay item to edit at the source. I’d like to hear, how you think Overlay’s will help you in your case, or how you are already using them... Enjoy SharePoint! --Sharad

Read the article

C# HashSet<T>

- by Ben Griswold

I hadn’t done much (read: anything) with the C# generic HashSet until I recently needed to produce a distinct collection. As it turns out, HashSet<T> was the perfect tool. As the following snippet demonstrates, this collection type offers a lot: // Using HashSet<T>: // http://www.albahari.com/nutshell/ch07.aspx var letters = new HashSet<char>("the quick brown fox"); Console.WriteLine(letters.Contains('t')); // true Console.WriteLine(letters.Contains('j')); // false foreach (char c in letters) Console.Write(c); // the quickbrownfx Console.WriteLine(); letters = new HashSet<char>("the quick brown fox"); letters.IntersectWith("aeiou"); foreach (char c in letters) Console.Write(c); // euio Console.WriteLine(); letters = new HashSet<char>("the quick brown fox"); letters.ExceptWith("aeiou"); foreach (char c in letters) Console.Write(c); // th qckbrwnfx Console.WriteLine(); letters = new HashSet<char>("the quick brown fox"); letters.SymmetricExceptWith("the lazy brown fox"); foreach (char c in letters) Console.Write(c); // quicklazy Console.WriteLine(); The MSDN documentation is a bit light on HashSet<T> documentation but if you search hard enough you can find some interesting information and benchmarks. But back to that distinct list I needed… // MSDN Add // http://msdn.microsoft.com/en-us/library/bb353005.aspx var employeeA = new Employee {Id = 1, Name = "Employee A"}; var employeeB = new Employee {Id = 2, Name = "Employee B"}; var employeeC = new Employee {Id = 3, Name = "Employee C"}; var employeeD = new Employee {Id = 4, Name = "Employee D"}; var naughty = new List<Employee> {employeeA}; var nice = new List<Employee> {employeeB, employeeC}; var employees = new HashSet<Employee>(); naughty.ForEach(x => employees.Add(x)); nice.ForEach(x => employees.Add(x)); foreach (Employee e in employees) Console.WriteLine(e); // Returns Employee A Employee B Employee C The Add Method returns true on success and, you guessed it, false if the item couldn’t be added to the collection. I’m using the Linq ForEach syntax to add all valid items to the employees HashSet. It works really great. This is just a rough sample, but you may have noticed I’m using Employee, a reference type. Most samples demonstrate the power of the HashSet with a collection of integers which is kind of cheating. With value types you don’t have to worry about defining your own equality members. With reference types, you do. internal class Employee { public int Id { get; set; } public string Name { get; set; } public override string ToString() { return Name; } public bool Equals(Employee other) { if (ReferenceEquals(null, other)) return false; if (ReferenceEquals(this, other)) return true; return other.Id == Id; } public override bool Equals(object obj) { if (ReferenceEquals(null, obj)) return false; if (ReferenceEquals(this, obj)) return true; if (obj.GetType() != typeof (Employee)) return false; return Equals((Employee) obj); } public override int GetHashCode() { return Id; } public static bool operator ==(Employee left, Employee right) { return Equals(left, right); } public static bool operator !=(Employee left, Employee right) { return !Equals(left, right); } } Fortunately, with Resharper, it’s a snap. Click on the class name, ALT+INS and then follow with the handy dialogues. That’s it. Try out the HashSet<T>. It’s good stuff.

Read the article

Getting TF215097 error after modifying a build process template in TFS Team Build 2010

- by Jakob Ehn

When embracing Team Build 2010, you typically want to define several different build process templates for different scenarios. Common examples here are CI builds, QA builds and release builds. For example, in a contiuous build you often have no interest in publishing to the symbol store, you might or might not want to associate changesets and work items etc. The build server is often heavily occupied as it is, so you don’t want to have it doing more that necessary. Try to define a set of build process templates that are used across your company. In previous versions of TFS Team Build, there was no easy way to do this. But in TFS 2010 it is very easy so there is no excuse to not do it! :-) I ran into a scenario today where I had an existing build definition that was based on our release build process template. In this template, we have defined several different build process parameters that control the release build. These are placed into its own sectionin the Build Process Parameters editor. This is done using the ProcessParameterMetadataCollection element, I will explain how this works in a future post. I won’t go into details on these parametes, the issue for this blog post is what happens when you modify a build process template so that it is no longer compatible with the build definition, i.e. a breaking change. In this case, I removed a parameter that was no longer necessary. After merging the new build process template to one of the projects and queued a new release build, I got this error: TF215097: An error occurred while initializing a build for build definition <Build Definition Name>: The values provided for the root activity's arguments did not satisfy the root activity's requirements: 'DynamicActivity': The following keys from the input dictionary do not map to arguments and must be removed: <Parameter Name>. Please note that argument names are case sensitive. Parameter name: rootArgumentValues <Parameter Name> was the parameter that I removed so it was pretty easy to understand why the error had occurred. However, it is not entirely obvious how to fix the problem. When open the build definition everything looks OK, the removed build process parameter is not there, and I can open the build process template without any validation warnings. The problem here is that all settings specific to a particular build definition is stored in the TFS database. In TFS 2005, everything that was related to a build was stored in TFS source control in files (TFSBuild.proj, WorkspaceMapping.xml..). In TFS 2008, many of these settings were moved into the database. Still, lots of things were stored in TFSBuild.proj, such as the solution and configuration to build, wether to execute tests or not. In TFS 2010, all settings for a build definition is stored in the database. If we look inside the database we can see what this looks like. The table tbl_BuildDefinition contains all information for a build definition. One of the columns is called ProcessParameters and contains a serialized representation of a Dictionary that is the underlying object where these settings are stoded. Here is an example: <Dictionary x:TypeArguments="x:String, x:Object" xmlns="clr-namespace:System.Collections.Generic;assembly=mscorlib" xmlns:mtbwa="clr-namespace:Microsoft.TeamFoundation.Build.Workflow.Activities;assembly=Microsoft.TeamFoundation.Build.Workflow" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml"> <mtbwa:BuildSettings x:Key="BuildSettings" ProjectsToBuild="$/PathToProject.sln"> <mtbwa:BuildSettings.PlatformConfigurations> <mtbwa:PlatformConfigurationList Capacity="4"> <mtbwa:PlatformConfiguration Configuration="Release" Platform="Any CPU" /> </mtbwa:PlatformConfigurationList> </mtbwa:BuildSettings.PlatformConfigurations> </mtbwa:BuildSettings> <mtbwa:AgentSettings x:Key="AgentSettings" Tags="Agent1" /> <x:Boolean x:Key="DisableTests">True</x:Boolean> <x:String x:Key="ReleaseRepositorySolution">ERP</x:String> <x:Int32 x:Key="Major">2</x:Int32> <x:Int32 x:Key="Minor">3</x:Int32> </Dictionary> Here we can see that it is really only the non-default values that are persisted into the databasen. So, the problem in my case was that I removed one of the parameteres from the build process template, but the parameter and its value still existed in the build definition database. The solution to the problem is to refresh the build definition and save it. In the process tab, there is a Refresh button that will reload the build definition and the process template and synchronize them: After refreshing the build definition and saving it, the build was running successfully again.

Read the article

How to Use Windows’ Advanced Search Features: Everything You Need to Know

- by Chris Hoffman

You should never have to hunt down a lost file on modern versions of Windows — just perform a quick search. You don’t even have to wait for a cartoon dog to find your files, like on Windows XP. The Windows search indexer is constantly running in the background to make quick local searches possible. This enables the kind of powerful search features you’d use on Google or Bing — but for your local files. Controlling the Indexer By default, the Windows search indexer watches everything under your user folder — that’s C:\Users\NAME. It reads all these files, creating an index of their names, contents, and other metadata. Whenever they change, it notices and updates its index. The index allows you to quickly find a file based on the data in the index. For example, if you want to find files that contain the word “beluga,” you can perform a search for “beluga” and you’ll get a very quick response as Windows looks up the word in its search index. If Windows didn’t use an index, you’d have to sit and wait as Windows opened every file on your hard drive, looked to see if the file contained the word “beluga,” and moved on. Most people shouldn’t have to modify this indexing behavior. However, if you store your important files in other folders — maybe you store your important data a separate partition or drive, such as at D:\Data — you may want to add these folders to your index. You can also choose which types of files you want to index, force Windows to rebuild the index entirely, pause the indexing process so it won’t use any system resources, or move the index to another location to save space on your system drive. To open the Indexing Options window, tap the Windows key on your keyboard, type “index”, and click the Indexing Options shortcut that appears. Use the Modify button to control the folders that Windows indexes or the Advanced button to control other options. To prevent Windows from indexing entirely, click the Modify button and uncheck all the included locations. You could also disable the search indexer entirely from the Programs and Features window. Searching for Files You can search for files right from your Start menu on Windows 7 or Start screen on Windows 8. Just tap the Windows key and perform a search. If you wanted to find files related to Windows, you could perform a search for “Windows.” Windows would show you files that are named Windows or contain the word Windows. From here, you can just click a file to open it. On Windows 7, files are mixed with other types of search results. On Windows 8 or 8.1, you can choose to search only for files. If you want to perform a search without leaving the desktop in Windows 8.1, press Windows Key + S to open a search sidebar. You can also initiate searches directly from Windows Explorer — that’s File Explorer on Windows 8. Just use the search box at the top-right of the window. Windows will search the location you’ve browsed to. For example, if you’re looking for a file related to Windows and know it’s somewhere in your Documents library, open the Documents library and search for Windows. Using Advanced Search Operators On Windows 7, you’ll notice that you can add “search filters” form the search box, allowing you to search by size, date modified, file type, authors, and other metadata. On Windows 8, these options are available from the Search Tools tab on the ribbon. These filters allow you to narrow your search results. If you’re a geek, you can use Windows’ Advanced Query Syntax to perform advanced searches from anywhere, including the Start menu or Start screen. Want to search for “windows,” but only bring up documents that don’t mention Microsoft? Search for “windows -microsoft”. Want to search for all pictures of penguins on your computer, whether they’re PNGs, JPEGs, or any other type of picture file? Search for “penguin kind:picture”. We’ve looked at Windows’ advanced search operators before, so check out our in-depth guide for more information. The Advanced Query Syntax gives you access to options that aren’t available in the graphical interface. Creating Saved Searches Windows allows you to take searches you’ve made and save them as a file. You can then quickly perform the search later by double-clicking the file. The file functions almost like a virtual folder that contains the files you specify. For example, let’s say you wanted to create a saved search that shows you all the new files created in your indexed folders within the last week. You could perform a search for “datecreated:this week”, then click the Save search button on the toolbar or ribbon. You’d have a new virtual folder you could quickly check to see your recent files. One of the best things about Windows search is that it’s available entirely from the keyboard. Just press the Windows key, start typing the name of the file or program you want to open, and press Enter to quickly open it. Windows 8 made this much more obnoxious with its non-unified search, but unified search is finally returning with Windows 8.1.

Read the article

Guarding against CSRF Attacks in ASP.NET MVC2

- by srkirkland

Alongside XSS (Cross Site Scripting) and SQL Injection, Cross-site Request Forgery (CSRF) attacks represent the three most common and dangerous vulnerabilities to common web applications today. CSRF attacks are probably the least well known but they are relatively easy to exploit and extremely and increasingly dangerous. For more information on CSRF attacks, see these posts by Phil Haack and Steve Sanderson. The recognized solution for preventing CSRF attacks is to put a user-specific token as a hidden field inside your forms, then check that the right value was submitted. It's best to use a random value which you’ve stored in the visitor’s Session collection or into a Cookie (so an attacker can't guess the value). ASP.NET MVC to the rescue ASP.NET MVC provides an HTMLHelper called AntiForgeryToken(). When you call <%= Html.AntiForgeryToken() %> in a form on your page you will get a hidden input and a Cookie with a random string assigned. Next, on your target Action you need to include [ValidateAntiForgeryToken], which handles the verification that the correct token was supplied. Good, but we can do better Using the AntiForgeryToken is actually quite an elegant solution, but adding [ValidateAntiForgeryToken] on all of your POST methods is not very DRY, and worse can be easily forgotten. Let's see if we can make this easier on the program but moving from an "Opt-In" model of protection to an "Opt-Out" model. Using AntiForgeryToken by default In order to mandate the use of the AntiForgeryToken, we're going to create an ActionFilterAttribute which will do the anti-forgery validation on every POST request. First, we need to create a way to Opt-Out of this behavior, so let's create a quick action filter called BypassAntiForgeryToken: [AttributeUsage(AttributeTargets.Method, AllowMultiple=false)] public class BypassAntiForgeryTokenAttribute : ActionFilterAttribute { } Now we are ready to implement the main action filter which will force anti forgery validation on all post actions within any class it is defined on: [AttributeUsage(AttributeTargets.Class, AllowMultiple = false)] public class UseAntiForgeryTokenOnPostByDefault : ActionFilterAttribute { public override void OnActionExecuting(ActionExecutingContext filterContext) { if (ShouldValidateAntiForgeryTokenManually(filterContext)) { var authorizationContext = new AuthorizationContext(filterContext.Controller.ControllerContext); //Use the authorization of the anti forgery token, //which can't be inhereted from because it is sealed new ValidateAntiForgeryTokenAttribute().OnAuthorization(authorizationContext); } base.OnActionExecuting(filterContext); } /// <summary> /// We should validate the anti forgery token manually if the following criteria are met: /// 1. The http method must be POST /// 2. There is not an existing [ValidateAntiForgeryToken] attribute on the action /// 3. There is no [BypassAntiForgeryToken] attribute on the action /// </summary> private static bool ShouldValidateAntiForgeryTokenManually(ActionExecutingContext filterContext) { var httpMethod = filterContext.HttpContext.Request.HttpMethod; //1. The http method must be POST if (httpMethod != "POST") return false; // 2. There is not an existing anti forgery token attribute on the action var antiForgeryAttributes = filterContext.ActionDescriptor.GetCustomAttributes(typeof(ValidateAntiForgeryTokenAttribute), false); if (antiForgeryAttributes.Length > 0) return false; // 3. There is no [BypassAntiForgeryToken] attribute on the action var ignoreAntiForgeryAttributes = filterContext.ActionDescriptor.GetCustomAttributes(typeof(BypassAntiForgeryTokenAttribute), false); if (ignoreAntiForgeryAttributes.Length > 0) return false; return true; } } The code above is pretty straight forward -- first we check to make sure this is a POST request, then we make sure there aren't any overriding *AntiForgeryTokenAttributes on the action being executed. If we have a candidate then we call the ValidateAntiForgeryTokenAttribute class directly and execute OnAuthorization() on the current authorization context. Now on our base controller, you could use this new attribute to start protecting your site from CSRF vulnerabilities. [UseAntiForgeryTokenOnPostByDefault] public class ApplicationController : System.Web.Mvc.Controller { } //Then for all of your controllers public class HomeController : ApplicationController {} What we accomplished If your base controller has the new default anti-forgery token attribute on it, when you don't use <%= Html.AntiForgeryToken() %> in a form (or of course when an attacker doesn't supply one), the POST action will throw the descriptive error message "A required anti-forgery token was not supplied or was invalid". Attack foiled! In summary, I think having an anti-CSRF policy by default is an effective way to protect your websites, and it turns out it is pretty easy to accomplish as well. Enjoy!

Read the article

Blending the Sketchflow Action

- by GeekAgilistMercenary

Started a new Sketchflow Prototype in Expression Blend recently and documented each of the steps. This blog entry covers some of those steps, which are the basic elements of any prototype. I will have more information regarding design, prototype creation, and the process of the initial phases for development in the future. For now, I hope you enjoy this short walk through. Also, be sure to check out my last quick entry on Sketchflow. I started off with a Sketchflow Project, just like I did in my previous entry (more specifics in that entry about how to manipulate and build out the Sketchflow Map). Once I created the project I setup the following Sketchflow Map. The CoreNavigation is a ComponentScreen setup solely for the page navigation at the top of the screen. The XAML markup in case you want to create a Component Screen with the same design is included below. <UserControl xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" mc:Ignorable="d" xmlns:i="clr-namespace:System.Windows.Interactivity;assembly=System.Windows.Interactivity" xmlns:pb="clr-namespace:Microsoft.Expression.Prototyping.Behavior;assembly=Microsoft.Expression.Prototyping.Interactivity" x:Class="RapidPrototypeSketchScreens.CoreNavigation" d:DesignWidth="624" d:DesignHeight="49" Height="49" Width="624"> <Grid x:Name="LayoutRoot"> <TextBlock HorizontalAlignment="Stretch" Margin="307,3,0,0" Style="{StaticResource TitleCenter-Sketch}" Text="Aütøchart Scorecards" TextWrapping="Wrap"> <i:Interaction.Triggers> <i:EventTrigger EventName="MouseLeftButtonDown"> <pb:NavigateToScreenAction TargetScreen="RapidPrototypeSketchScreens.Screen_1"/> </i:EventTrigger> </i:Interaction.Triggers> </TextBlock> <Button HorizontalAlignment="Left" Margin="164,8,0,11" Style="{StaticResource Button-Sketch}" Width="144" Content="Scorecard"> <i:Interaction.Triggers> <i:EventTrigger EventName="Click"> <pb:NavigateToScreenAction TargetScreen="RapidPrototypeSketchScreens.Screen_1_2"/> </i:EventTrigger> </i:Interaction.Triggers> </Button> <Button HorizontalAlignment="Left" Margin="8,8,0,11" Style="{StaticResource Button-Sketch}" Width="152" Content="Standard Reports"> <i:Interaction.Triggers> <i:EventTrigger EventName="Click"> <pb:NavigateToScreenAction TargetScreen="RapidPrototypeSketchScreens.Screen_1_1"/> </i:EventTrigger> </i:Interaction.Triggers> </Button> </Grid> </UserControl> Now that the CoreNavigation Component Screen is done I built out each of the others. In each of those screens I included the CoreNavigation Screen (all those little green lines in the image) as the top navigation. In order to do that, as I created each of the pages I would hover over the CoreNavigation Object in the Sketchflow Map. When the utilities drawer (the small menu that pops down under a node when you hover over it) shows click on the third little icon and drag it onto the page node you want a navigation screen on. Once I created all the screens I setup the navigation by opening up each screen and right clicking on the objects that needed to point to somewhere else in the prototype. Once I was done with the main page, my Home Navigation Page, it looked something like this in the Expression Blend Designer. I fleshed out each of the additional screens. Once I was done I wanted to try out the deployment package. The way to deploy a Sketchflow Prototype is to merely click on File –> Package SketchFlow Project and a prompt will appear. In the prompt enter what you want the package to be called. I like to see the files generated afterwards too, so I checked the box to see that. When Expression Blend is done generating everything you’ll have a directory like the one shown below, with all the needed files for deployment. Now these files can be copied or moved to any location for viewing. One can even copy them (such as via FTP) to a server location to share with others. Once they are deployed and you run the "TestPage.html" the other features of the Sketchflow Package are available. In the image below I have tagged a few sections to show the Sketchflow Player Features. To the top left is the navigation, which provides a clearly defined area of movement in a list. To the center right is the actual prototype application. I have placed lists of things and made edits. On the left hand side is the highlight feature, which is available in the Feedback section of the lower left. On the right hand list I underlined the Autochart with an orange marker, and marked out two list items with a red marker. In the lower left hand side in the Feedback section is also an area to type in your feedback. This can be useful for time based feedback, when you post this somewhere and want people to provide subsequent follow up feedback. Overall lots of great features, that enable some fairly rapid prototyping with customers. Once one is familiar with the steps and parts of this Sketchflow Prototype Capabilities it is easy to step through an application without even stopping. It really is that easy. So get hold of Expression Blend 3 and get ramped up on Sketchflow, it will pay off in the design phases to do so! Original Entry

Read the article

Ask How-To Geek: Learning the Office Ribbon, Booting to USB with an Old BIOS, and Snapping Windows

- by Jason Fitzpatrick

You’ve got questions and we’ve got answers. Today we highlight how to master the new Office interface, USB boot a computer with outdated BIOS, and snap windows to preset locations. Learning the New Office Ribbon Dear How-To Geek, I feel silly asking this (in light of how long the new Office interface has been out) but my company finally got around to upgrading from Windows XP and Office 2000 so the new interface it totally new to me. Can you recommend any resources for quickly learning the Office ribbon and the new changes? I feel completely lost after two decades of the old Office interface. Help! Sincerely, Where the Hell is Everything? Dear Where the Hell, We think most people were with you at some point in the last few years. “Where the hell is…” could possibly be the slogan for the new ribbon interface. You could browse through some of the dry tutorials online or even get a weighty book on the topic but the best way to learn something new is to get hands on. Ribbon Hero turns learning the new Office features and ribbon layout into a game. It’s no vigorous round of Team Fortress mind you, but it’s significantly more fun than reading a training document. Check out how to install and configure Ribbon Hero here. You’ll be teaching your coworkers new tricks in no time. Boot via USB with an Old BIOS Dear How-To Geek, I’m trying to repurpose some old computers by updating them with lightweight Linux distros but the BIOS on most of the machines is ancient and creaky. How ancient? It doesn’t even support booting from a USB device! I have a large flash drive that I’ve turned into a master installation tool for jobs like this but I can’t use it. The computers in question have USB ports; they just aren’t recognized during the boot process. What can I do? USB Bootin’ in Boise Dear USB Bootin’, It’s great you’re working to breathe life into old hardware! You’ve run into one of the limitations of older BIOSes, USB was around but nobody was thinking about booting off of it. Fortunately if you have a computer old enough to have that kind of BIOS it’s likely to also has a floppy drive or a CDROM drive. While you could make a bootable CDROM for your application we understand that you want to keep using the master USB installer you’ve made. In light of that we recommend PLoP Boot Manager. Think of it like a boot manager for your boot manager. Using it you can create a bootable floppy or CDROM that will enable USB booting of your master USB drive. Make a CD and a floppy version and you’ll have everything in your toolkit you need for future computer refurbishing projects. Read up on creating bootable media with PLoP Boot Manager here. Snapping Windows to Preset Coordinates Dear How-To Geek, Once upon a time I had a company laptop that came with a little utility that snapped windows to preset areas of the screen. This was long before the snap-to-side features in Windows 7. You could essentially configure your screen into a grid pattern of your choosing and then windows would neatly snap into those grids. I have no idea what it was called or if was anymore than a gimmick from the computer manufacturer, but I’d really like to have it on my new computer! Bend and Snap in San Francisco, Dear Bend and Snap, If we had to guess, we’d guess your company must have had a set of laptops from Acer as the program you’re describing sounds exactly like Acer GridVista. Fortunately for you the application was extremely popular and Acer released it independently of their hardware. If, by chance, you’ve since upgraded to a multiple monitor setup the app even supports multiple monitors—many of the configurations are handy for arranging IM windows and other auxiliary communication tools. Check out our guide to installing and configuring Acer GridVista here for more information. Have a question you want to put before the How-To Geek staff? Shoot us an email at [email protected] and then keep an eye out for a solution in the Ask How-To Geek column. Latest Features How-To Geek ETC How to Upgrade Windows 7 Easily (And Understand Whether You Should) The How-To Geek Guide to Audio Editing: Basic Noise Removal Install a Wii Game Loader for Easy Backups and Fast Load Times The Best of CES (Consumer Electronics Show) in 2011 The Worst of CES (Consumer Electronics Show) in 2011 HTG Projects: How to Create Your Own Custom Papercraft Toy Download the New Year in Japan Windows 7 Theme from Microsoft Once More Unto the Breach – Facebook Apps Can Now Access Your Address and Phone Number Dial Zero Speeds You Through Annoying Customer Service Menus Complete Dropquest 2011 and Receive Free Dropbox Storage Desktop Computer versus Laptop Wallpaper The Kids Have No Idea What Old Tech Is [Video]

Read the article

Update Manager unable to get updates

- by dPEN

In last few days my Ubuntu 11.10 update manager is unable to get new updates. When I checked update log I saw that for couple of updates it says "Network isn't available". For other updates it downloaded logs and and internet connection also works fine. Unable to attached screenshot due to SPAM prevention policy. But for below Release gpgv:/var/lib/apt/lists/partial/extras.ubuntu.com_ubuntu_dists_oneiric_Release.gpg it says "Network isn't available" For all other Releases it is downloading fine. And due to this I dont see any update available in last 10 days. LOG OF sudo apt-get update: dipen@EIDLCPU1018:~$ sudo apt-get update [sudo] password for dipen: Ign http:/extras.ubuntu.com oneiric InRelease Ign http:/archive.canonical.com oneiric InRelease Ign http:/archive.canonical.com lucid InRelease Get:1 http:/extras.ubuntu.com oneiric Release.gpg [72 B] Get:2 http:/archive.canonical.com oneiric Release.gpg [198 B] Hit http:/extras.ubuntu.com oneiric Release Get:3 http:/archive.canonical.com lucid Release.gpg [198 B] Err http:/extras.ubuntu.com oneiric Release Hit http:/archive.canonical.com oneiric Release Ign http:/archive.canonical.com oneiric Release Hit http:/archive.canonical.com lucid Release Ign http:/archive.canonical.com lucid Release Ign http:/archive.canonical.com oneiric/partner i386 Packages/DiffIndex Ign http:/archive.canonical.com oneiric/partner TranslationIndex Ign http:/archive.canonical.com lucid/partner i386 Packages/DiffIndex Ign http:/archive.canonical.com lucid/partner TranslationIndex Hit http:/archive.canonical.com oneiric/partner i386 Packages Hit http:/archive.canonical.com lucid/partner i386 Packages Ign http:/dl.google.com stable InRelease Ign http:/archive.canonical.com oneiric/partner Translation-en_IN Ign http:/archive.canonical.com oneiric/partner Translation-en Ign http:/archive.canonical.com lucid/partner Translation-en_IN Ign http:/archive.canonical.com lucid/partner Translation-en Ign http:/in.archive.ubuntu.com oneiric InRelease Ign http:/in.archive.ubuntu.com oneiric-updates InRelease Ign http:/in.archive.ubuntu.com oneiric-security InRelease Get:4 http//dl.google.com stable Release.gpg [198 B] Get:5 http//in.archive.ubuntu.com oneiric Release.gpg [198 B] Get:6 http//in.archive.ubuntu.com oneiric-updates Release.gpg [198 B] Get:7 http//in.archive.ubuntu.com oneiric-security Release.gpg [198 B] Hit http:/in.archive.ubuntu.com oneiric Release Ign http:/in.archive.ubuntu.com oneiric Release Hit http:/in.archive.ubuntu.com oneiric-updates Release Err http:/in.archive.ubuntu.com oneiric-updates Release Hit http:/in.archive.ubuntu.com oneiric-security Release Ign http:/in.archive.ubuntu.com oneiric-security Release Ign http:/in.archive.ubuntu.com oneiric/main i386 Packages/DiffIndex Ign http:/in.archive.ubuntu.com oneiric/restricted i386 Packages/DiffIndex Ign http:/in.archive.ubuntu.com oneiric/universe i386 Packages/DiffIndex Ign http:/in.archive.ubuntu.com oneiric/multiverse i386 Packages/DiffIndex Hit http:/in.archive.ubuntu.com oneiric/main TranslationIndex Hit http:/in.archive.ubuntu.com oneiric/multiverse TranslationIndex Hit http:/in.archive.ubuntu.com oneiric/restricted TranslationIndex Hit http:/in.archive.ubuntu.com oneiric/universe TranslationIndex Ign http:/in.archive.ubuntu.com oneiric-security/main i386 Packages/DiffIndex Ign http:/in.archive.ubuntu.com oneiric-security/restricted i386 Packages/DiffIndex Ign http:/in.archive.ubuntu.com oneiric-security/universe i386 Packages/DiffIndex Ign http:/in.archive.ubuntu.com oneiric-security/multiverse i386 Packages/DiffIndex Hit http:/in.archive.ubuntu.com oneiric-security/main TranslationIndex Hit http:/in.archive.ubuntu.com oneiric-security/multiverse TranslationIndex Hit http:/in.archive.ubuntu.com oneiric-security/restricted TranslationIndex Hit http:/in.archive.ubuntu.com oneiric-security/universe TranslationIndex Hit http:/in.archive.ubuntu.com oneiric/main i386 Packages Hit http:/in.archive.ubuntu.com oneiric/restricted i386 Packages Hit http:/in.archive.ubuntu.com oneiric/universe i386 Packages Hit http:/in.archive.ubuntu.com oneiric/multiverse i386 Packages Hit http:/in.archive.ubuntu.com oneiric/main Translation-en Hit http:/in.archive.ubuntu.com oneiric/multiverse Translation-en Hit http:/in.archive.ubuntu.com oneiric/restricted Translation-en Hit http:/in.archive.ubuntu.com oneiric/universe Translation-en Hit http:/in.archive.ubuntu.com oneiric-security/main i386 Packages Hit http:/in.archive.ubuntu.com oneiric-security/restricted i386 Packages Hit http:/in.archive.ubuntu.com oneiric-security/universe i386 Packages Hit http:/in.archive.ubuntu.com oneiric-security/multiverse i386 Packages Hit http:/in.archive.ubuntu.com oneiric-security/main Translation-en Hit http:/in.archive.ubuntu.com oneiric-security/multiverse Translation-en Get:8 http//dl.google.com stable Release [1,347 B] Hit http:/in.archive.ubuntu.com oneiric-security/restricted Translation-en Hit http:/in.archive.ubuntu.com oneiric-security/universe Translation-en Get:9 http//dl.google.com stable/main i386 Packages [1,214 B] Ign http:/dl.google.com stable/main TranslationIndex Ign http:/dl.google.com stable/main Translation-en_IN Ign http:/dl.google.com stable/main Translation-en Fetched 3,821 B in 41s (91 B/s) Reading package lists... Done W: A error occurred during the signature verification. The repository is not updated and the previous index files will be used. GPG error: http:/extras.ubuntu.com oneiric Release: The following signatures were invalid: BADSIG 16126D3A3E5C1192 Ubuntu Extras Archive Automatic Signing Key <[email protected]> W: GPG error: http:/archive.canonical.com oneiric Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: GPG error: http:/archive.canonical.com lucid Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: GPG error: http:/in.archive.ubuntu.com oneiric Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: A error occurred during the signature verification. The repository is not updated and the previous index files will be used. GPG error: http:/in.archive.ubuntu.com oneiric-updates Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: GPG error: http:/in.archive.ubuntu.com oneiric-security Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: Failed to fetch http:/extras.ubuntu.com/ubuntu/dists/oneiric/Release W: Failed to fetch http:/in.archive.ubuntu.com/ubuntu/dists/oneiric-updates/Release W: Some index files failed to download. They have been ignored, or old ones used instead. dipen@EIDLCPU1018:~$ LOG of sudo apt-get upgrade: dipen@EIDLCPU1018:~$ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages have been kept back: ghc6-doc haskell-zlib-doc libghc6-zlib-doc 0 upgraded, 0 newly installed, 0 to remove and 3 not upgraded. dipen@EIDLCPU1018:~$ /etc/apt/sources.list: deb http:/in.archive.ubuntu.com/ubuntu/ oneiric main restricted deb http:/in.archive.ubuntu.com/ubuntu/ oneiric-updates main restricted deb http:/in.archive.ubuntu.com/ubuntu/ oneiric universe deb http:/in.archive.ubuntu.com/ubuntu/ oneiric-updates universe deb http:/in.archive.ubuntu.com/ubuntu/ oneiric multiverse deb http:/in.archive.ubuntu.com/ubuntu/ oneiric-updates multiverse deb http:/archive.canonical.com/ubuntu oneiric partner deb http:/in.archive.ubuntu.com/ubuntu/ oneiric-security main restricted deb http:/in.archive.ubuntu.com/ubuntu/ oneiric-security universe deb http:/in.archive.ubuntu.com/ubuntu/ oneiric-security multiverse deb http:/extras.ubuntu.com/ubuntu oneiric main #Third party developers repository deb http:/archive.canonical.com/ lucid partner

Read the article

Remove Office 2010 Beta and Reinstall Office 2007

- by Matthew Guay

Have you tried out the Office 2010 beta, but want to go back to Office 2007? Here’s a step-by-step tutorial on how to remove your Office 2010 beta and reinstall your Office 2007. The Office 2010 beta will expire on October 31, 2010, at which time you may see a dialog like the one below. At that time, you will need to either upgrade to the final release of Office 2010, or reinstall your previous version of Office. Our computer was running the Office 2010 Home and Business Click to Run beta, and after uninstalling it we reinstalled Office 2007 Home and Student. This was a Windows Vista computer, but the process will be exactly the same on Windows XP, Vista, or Windows 7. Additionally, the process to reinstall Office 2007 will be exactly the same regardless of the edition of Office 2007 you’re using. However, please note that if you are running a different edition of Office 2010, especially the 64 bit version, the process may be slightly different. We will cover this scenario in another article. Remove Office 2010 Click to Run Beta: To remove Office 2010 Click to Run Beta, open Control Panel and select Uninstall a Program. If your computer is running Windows 7, enter “Uninstall a program” in your Start menu search. Scroll down, select “Microsoft Office Click-to-Run 2010 (Beta)”, and click the Uninstall button on the toolbar. Note that there will be two entries for Office, so make sure to select the “Click-to-Run” entry. This will automatically remove all of Office 2010 and its components. Click Yes to confirm you want to remove it. Office 2010 beta uninstalled fairly quickly, and a reboot will be required. Once your computer is rebooted, Office 2010 will be entirely removed. Reinstall Office 2007 Now, you’re to the easy part. Simply insert your Office 2007 CD, and it should automatically startup the setup. If not, open Computer and double-click on your CD drive. Now, double-click on setup.exe to start the installation. Enter your product key, and click Continue… Click Install Now, or click Customize if you want to change the default installation settings. Wait while Office 2007 installs…it takes around 15 to 20 minutes in our experience. Once it’s finished close the installer. Now, open one of the Office applications. A popup will open asking you to activate Office. Make sure you’re connected to the internet, and click next; otherwise, you can select to activate over the phone if you do not have internet access. This should only take a minute, and Office 2007 will be activated and ready to run. Everything should work just as it did before you installed Office 2010. Enjoy! Office Updates Make sure to install the latest updates for Office 2007, as these are not included in your disk. Check Windows Update (search for Windows Update in the Start menu search), and install all of the available updates for Office 2007, including Service Pack 2. Conclusion This is a great way to keep using Office even if you don’t decide to purchase Office 2010 after it is released. Additionally, if you’re were using another version of Office, such as Office 2003, then reinstall it as normal after following the steps to remove Office 2010. Similar Articles Productive Geek Tips Add or Remove Apps from the Microsoft Office 2007 or 2010 SuiteDetect and Repair Applications In Microsoft Office 2007Save and Restore Your Microsoft Office SettingsDisable Office 2010 Beta Send-a-Smile from StartupHow to See the About Dialog and Version Information in Office 2007 TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 If Web Browsers Were Modes of Transportation Google Translate (for animals) Out of 100 Tweeters Roadkill’s Scan Port scans for open ports Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows

Read the article

JMS Step 1 - How to Create a Simple JMS Queue in Weblogic Server 11g

- by John-Brown.Evans

JMS Step 1 - How to Create a Simple JMS Queue in Weblogic Server 11g ol{margin:0;padding:0} .c5{vertical-align:top;width:156pt;border-style:solid;border-color:#000000;border-width:1pt;padding:0pt 2pt 0pt 2pt} .c7{list-style-type:disc;margin:0;padding:0} .c4{background-color:#ffffff} .c14{color:#1155cc;text-decoration:underline} .c6{height:11pt;text-align:center} .c13{color:inherit;text-decoration:inherit} .c3{padding-left:0pt;margin-left:36pt} .c0{border-collapse:collapse} .c12{text-align:center} .c1{direction:ltr} .c8{background-color:#f3f3f3} .c2{line-height:1.0} .c11{font-style:italic} .c10{height:11pt} .c9{font-weight:bold} .title{padding-top:24pt;line-height:1.15;text-align:left;color:#000000;font-size:36pt;font-family:"Arial";font-weight:bold;padding-bottom:6pt}.subtitle{padding-top:18pt;line-height:1.15;text-align:left;color:#666666;font-style:italic;font-size:24pt;font-family:"Georgia";padding-bottom:4pt} li{color:#000000;font-size:10pt;font-family:"Arial"} p{color:#000000;font-size:10pt;margin:0;font-family:"Arial"} h1{padding-top:0pt;line-height:1.15;text-align:left;color:#666;font-size:18pt;font-family:"Arial";font-weight:normal;padding-bottom:0pt} h2{padding-top:0pt;line-height:1.15;text-align:left;color:#666;font-size:14pt;font-family:"Arial";font-weight:normal;padding-bottom:0pt} h3{padding-top:0pt;line-height:1.15;text-align:left;color:#666;font-size:12pt;font-family:"Arial";font-weight:normal;padding-bottom:0pt} h4{padding-top:0pt;line-height:1.15;text-align:left;color:#666;font-style:italic;font-size:11pt;font-family:"Arial";padding-bottom:0pt} h5{padding-top:0pt;line-height:1.15;text-align:left;color:#666;font-size:10pt;font-family:"Arial";font-weight:normal;padding-bottom:0pt} h6{padding-top:0pt;line-height:1.15;text-align:left;color:#666;font-style:italic;font-size:10pt;font-family:"Arial";padding-bottom:0pt} This example shows the steps to create a simple JMS queue in WebLogic Server 11g for testing purposes. For example, to use with the two sample programs QueueSend.java and QueueReceive.java which will be shown in later examples. Additional, detailed information on JMS can be found in the following Oracle documentation: Oracle® Fusion Middleware Configuring and Managing JMS for Oracle WebLogic Server 11g Release 1 (10.3.6) Part Number E13738-06 http://docs.oracle.com/cd/E23943_01/web.1111/e13738/toc.htm 1. Introduction and Definitions A JMS queue in Weblogic Server is associated with a number of additional resources: JMS Server A JMS server acts as a management container for resources within JMS modules. Some of its responsibilities include the maintenance of persistence and state of messages and subscribers. A JMS server is required in order to create a JMS module. JMS Module A JMS module is a definition which contains JMS resources such as queues and topics. A JMS module is required in order to create a JMS queue. Subdeployment JMS modules are targeted to one or more WLS instances or a cluster. Resources within a JMS module, such as queues and topics are also targeted to a JMS server or WLS server instances. A subdeployment is a grouping of targets. It is also known as advanced targeting. Connection Factory A connection factory is a resource that enables JMS clients to create connections to JMS destinations. JMS Queue A JMS queue (as opposed to a JMS topic) is a point-to-point destination type. A message is written to a specific queue or received from a specific queue. The objects used in this example are: Object Name Type JNDI Name TestJMSServer JMS Server TestJMSModule JMS Module TestSubDeployment Subdeployment TestConnectionFactory Connection Factory jms/TestConnectionFactory TestJMSQueue JMS Queue jms/TestJMSQueue 2. Configuration Steps The following steps are done in the WebLogic Server Console, beginning with the left-hand navigation menu. 2.1 Create a JMS Server Services > Messaging > JMS Servers Select New Name: TestJMSServer Persistent Store: (none) Target: soa_server1 (or choose an available server) Finish The JMS server should now be visible in the list with Health OK. 2.2 Create a JMS Module Services > Messaging > JMS Modules Select New Name: TestJMSModule Leave the other options empty Targets: soa_server1 (or choose the same one as the JMS server)Press Next Leave “Would you like to add resources to this JMS system module” unchecked and press Finish . 2.3 Create a SubDeployment A subdeployment is not necessary for the JMS queue to work, but it allows you to easily target subcomponents of the JMS module to a single target or group of targets. We will use the subdeployment in this example to target the following connection factory and JMS queue to the JMS server we created earlier. Services > Messaging > JMS Modules Select TestJMSModule Select the Subdeployments tab and New Subdeployment Name: TestSubdeployment Press Next Here you can select the target(s) for the subdeployment. You can choose either Servers (i.e. WebLogic managed servers, such as the soa_server1) or JMS Servers such as the JMS Server created earlier. As the purpose of our subdeployment in this example is to target a specific JMS server, we will choose the JMS Server option. Select the TestJMSServer created earlier Press Finish 2.4 Create a Connection Factory Services > Messaging > JMS Modules Select TestJMSModule and press New Select Connection Factory and Next Name: TestConnectionFactory JNDI Name: jms/TestConnectionFactory Leave the other values at default On the Targets page, select the Advanced Targeting button and select TestSubdeployment Press Finish The connection factory should be listed on the following page with TestSubdeployment and TestJMSServer as the target. 2.5 Create a JMS Queue Services > Messaging > JMS Modules Select TestJMSModule and press New Select Queue and Next Name: TestJMSQueueJNDI Name: jms/TestJMSQueueTemplate: NonePress Next Subdeployments: TestSubdeployment Finish The TestJMSQueue should be listed on the following page with TestSubdeployment and TestJMSServer. Confirm the resources for the TestJMSModule. Using the Domain Structure tree, navigate to soa_domain > Services > Messaging > JMS Modules then select TestJMSModule You should see the following resources The JMS queue is now complete and can be accessed using the JNDI names jms/TestConnectionFactory andjms/TestJMSQueue. In the following blog post in this series, I will show you how to write a message to this queue, using the WebLogic sample Java program QueueSend.java.

Read the article

Secure wipe of a hard drive using WinPE.

- by Derek Meier

Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} The wiping of a hard drive is typically seen as fairly trivial. There are tons of applications out there that will do it for you. Point àClickàGlobal-Thermo Nuclear War. However, these applications are typically expensive or unreliable. Plus, if you have a laptop or lack a secondary computer to put the hard drive into – how on earth do you wipe it quickly and easily while still conforming to a 7 pass rule (this means that every possible bit on the hard drive is set to 0 and then to 1 seven times in a row)? Yes, one pass should be enough – as turning every bit from a 1 to a zero will wipe the data from existence. But, we’re dealing with tinfoil hat wearing types here people. DOD standards dictate at least 3 passes, and typically 7 is the preferred amount. I’m not going to argue about data recovery. I have been told to use 7 passes, and so I will. So say we all! Quite some time ago I used to make a BartPE XP-based boot cd for the original purpose of securely wiping data. I loved BartPE and integrated so many plugins into my builds that I could do pretty much anything directly from CD. Reset passwords, uninstall security updates, wipe drives, chkdsk, remove spyware, install Windows, etc. However, with the newer multi-core systems and new chipsets coming out from vendors, I found that BartPE was rather difficult to keep up to date. I have since switched to WinPE 3.0 (Windows Preinstallation Environment). http://technet.microsoft.com/en-us/library/cc748933(WS.10).aspx It is fairly simple to create your own CD, and I have made a few helpful scripts to easily integrate drivers and rebuild the ISO file for you. I’ll cover making your own boot CD utilizing WinPE 3.0 in a later post – I can talk about WinPE forever and need to collect my thoughts!! My wife loves talking about WinPE almost as much as talking about Doctor Who. Wait, did I say loves? Hmmmm, I may have meant loathes. The topic at hand? Right. Wiping a drive! I must have drunk too much coffee this morning. I like to use a simple batch script that calls a combination of diskpart.exe from Microsoft® and Sdelete.exe created by our friend Mark Russinovich. http://technet.microsoft.com/en-us/sysinternals/bb897443.aspx All of the following files are located within the same directory on my WinPE boot CD. Here are the contents of wipe_me.bat, script.txt and sdelete.reg. Wipe_me.bat: @echo off echo. echo I will completely wipe the local hard drives using echo 7 individual wipes. The data will NOT echo be recoverable. I will begin after you pause echo. echo Preparing to partition and format disk. Diskpart.exe /s "script.txt" REM I was annoyed by not having a completely automated script – and Sdelete wants you to accept the license agreement. So, I added a registry file to skip doing that. regedit /S sdelete.reg rem sdelete options selected are: -p (passes) -c (zero free space) -s (recurse through subdirectories, if any) -z (clean free space) [drive letter] sdelete.exe -p 7 -c -s -z c: echo. echo Pass seven complete. echo. echo Wiping complete. Pause exit script.txt: list disk select disk 0 clean create partition primary select partition 1 active format FS=NTFS LABEL="New Volume" QUICK assign letter=c exit *Notes: This script assumes one local hard drive – change the script as you see fit for your environment. The clean command will overwrite the master boot record and any hidden sector information – so be careful! sdelete.reg: Windows Registry Editor Version 5.00 [HKEY_CURRENT_USER\Software\Sysinternals\SDelete] "EulaAccepted"=dword:00000001 With a combination of WinPE, sdelete.exe and your friendly neighborhood text editor you can begin wiping drives as quickly and easily as possible! I hope this helps, I get asked this a lot in my line of work. Best of luck, Derek

Read the article

Cannot install mysql-server (5.5.22) on clean ubuntu 12.04 LTS server

- by Christian

I have a clean minimal install of Ubuntu 12.04 LTS server 64-bit (just a root user and nothing alse installed). I tried to install the mysql-server with the following command: apt-get install mysql-server The installation aborts with the following error: The following NEW packages will be installed: libdbd-mysql-perl{a} libmysqlclient18{a} mysql-client mysql-client-5.5{a} mysql-client-core-5.5{a} mysql-common{a} mysql-server mysql-server-5.5{a} mysql-server-core-5.5{a} 0 packages upgraded, 9 newly installed, 0 to remove and 0 not upgraded. Need to get 11.7 kB/26.2 MB of archives. After unpacking 94.5 MB will be used. Do you want to continue? [Y/n/?] y Get: 1 http://mirror.eu.oneandone.net/ubuntu/ubuntu/ precise/main mysql-client all 5.5.22-0ubuntu1 [11.7 kB] Fetched 11.7 kB in 0s (567 kB/s) Preconfiguring packages ... Selecting previously unselected package mysql-common. (Reading database ... 54008 files and directories currently installed.) Unpacking mysql-common (from .../mysql-common_5.5.22-0ubuntu1_all.deb) ... Selecting previously unselected package libmysqlclient18. Unpacking libmysqlclient18 (from .../libmysqlclient18_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package libdbd-mysql-perl. Unpacking libdbd-mysql-perl (from .../libdbd-mysql-perl_4.020-1build2_amd64.deb) ... Selecting previously unselected package mysql-client-core-5.5. Unpacking mysql-client-core-5.5 (from .../mysql-client-core-5.5_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package mysql-client-5.5. Unpacking mysql-client-5.5 (from .../mysql-client-5.5_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package mysql-server-core-5.5. Unpacking mysql-server-core-5.5 (from .../mysql-server-core-5.5_5.5.22-0ubuntu1_amd64.deb) ... Processing triggers for man-db ... Setting up mysql-common (5.5.22-0ubuntu1) ... Selecting previously unselected package mysql-server-5.5. (Reading database ... 54189 files and directories currently installed.) Unpacking mysql-server-5.5 (from .../mysql-server-5.5_5.5.22-0ubuntu1_amd64.deb) ... Selecting previously unselected package mysql-client. Unpacking mysql-client (from .../mysql-client_5.5.22-0ubuntu1_all.deb) ... Selecting previously unselected package mysql-server. Unpacking mysql-server (from .../mysql-server_5.5.22-0ubuntu1_all.deb) ... Processing triggers for ureadahead ... Processing triggers for man-db ... Setting up libmysqlclient18 (5.5.22-0ubuntu1) ... Setting up libdbd-mysql-perl (4.020-1build2) ... Setting up mysql-client-core-5.5 (5.5.22-0ubuntu1) ... Setting up mysql-client-5.5 (5.5.22-0ubuntu1) ... Setting up mysql-server-core-5.5 (5.5.22-0ubuntu1) ... Setting up mysql-server-5.5 (5.5.22-0ubuntu1) ... 120502 10:17:41 [Note] Plugin 'FEDERATED' is disabled. 120502 10:17:41 InnoDB: The InnoDB memory heap is disabled 120502 10:17:41 InnoDB: Mutexes and rw_locks use GCC atomic builtins 120502 10:17:41 InnoDB: Compressed tables use zlib 1.2.3.4 120502 10:17:41 InnoDB: Initializing buffer pool, size = 128.0M 120502 10:17:41 InnoDB: Completed initialization of buffer pool 120502 10:17:41 InnoDB: highest supported file format is Barracuda. 120502 10:17:41 InnoDB: Waiting for the background threads to start 120502 10:17:42 InnoDB: 1.1.8 started; log sequence number 1595675 120502 10:17:42 InnoDB: Starting shutdown... 120502 10:17:42 InnoDB: Shutdown completed; log sequence number 1595675 start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Setting up mysql-client (5.5.22-0ubuntu1) ... dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because MaxReports is reached already Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: mysql-server-5.5 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up mysql-server-5.5 (5.5.22-0ubuntu1) ... start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: mysql-server-5.5 mysql-server I am completely lost because I have tried everything on the web to solve my problem (clearning the install, reconfiguring with dpkg, manually editing the my.cnf). I also set up a new clean install but nothing helped. What am I doing wrong? New information: The file /var/log/upstart/mysql.log contains the following error after the installation: AppArmor parser error for /etc/apparmor.d/usr.sbin.mysqld in /etc/apparmor.d/tunables/global at line 17: Could not open 'tunables/proc'

Read the article

Oracle Announces New Oracle Exastack Program for ISV Partners

- by pfolgado

Oracle Exastack Program Enables ISV Partners to Leverage a Scalable, Integrated Infrastructure to Deliver Their Applications Tuned and Optimized for High-Performance News Facts Enabling Independent Software Vendors (ISVs) and other members of Oracle Partner Network (OPN) to rapidly build and deliver faster, more reliable applications to end customers, Oracle today introduced Oracle Exastack Ready, available now, and Oracle Exastack Optimized, available in fall 2011 through OPN. The Oracle Exastack Program focuses on helping ISVs run their solutions on Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud -- integrated systems in which the software and hardware are engineered to work together. These products provide partners with a lower cost and high performance infrastructure for database and application workloads across on-premise and cloud based environments. Leveraging the new Oracle Exastack Program in which applications can qualify as Oracle Exastack Ready or Oracle Exastack Optimized, partners can use available OPN resources to optimize their applications to run faster and more reliably -- providing increased performance to their end users. By deploying their applications on Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud, ISVs can reduce the cost, time and support complexities typically associated with building and maintaining a disparate application infrastructure -- enabling them to focus more on their core competencies, accelerating innovation and delivering superior value to customers. After qualifying their applications as Oracle Exastack Ready, partners can note to customers that their applications run on and support Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud component products including Oracle Solaris, Oracle Linux, Oracle Database and Oracle WebLogic Server. Customers can be confident when choosing a partner's Oracle Exastack Optimized application, knowing it has been tuned by the OPN member on Oracle Exadata Database Machine or Oracle Exalogic Elastic Cloud with a goal of delivering optimum speed, scalability and reliability. Partners participating in the Oracle Exastack Program can also leverage their Oracle Exastack Ready and Oracle Exastack Optimized applications to advance to Platinum or Diamond level in OPN. Oracle Exastack Programs Provide ISVs a Reliable, High-Performance Application Infrastructure With the Oracle Exastack Program ISVs have several options to qualify and tune their applications with Oracle Exastack, including: Oracle Exastack Ready: Oracle Exastack Ready provides qualifying partners with specific branding and promotional benefits based on their adoption of Oracle products. If a partner application supports the latest major release of one of these products, the partner may use the corresponding logo with their product marketing materials: Oracle Solaris Ready, Oracle Linux Ready, Oracle Database Ready, and Oracle WebLogic Ready. Oracle Exastack Ready is available to OPN members at the Gold level or above. Additionally, OPN members participating in the program can leverage their Oracle Exastack Ready applications toward advancement to the Platinum or Diamond levels in the OPN Specialized program and toward achieving Oracle Exastack Optimized status. Oracle Exastack Optimized: When available, for OPN members at the Gold level or above, Oracle Exastack Optimized will provide direct access to Oracle technical resources and dedicated Oracle Exastack lab environments so OPN members can test and tune their applications to deliver optimal performance and scalability on Oracle Exadata Database Machine or Oracle Exalogic Elastic Cloud. Oracle Exastack Optimized will provide OPN members with specific branding and promotional benefits including the use of the Oracle Exastack Optimized logo. OPN members participating in the program will also be able to leverage their Oracle Exastack Optimized applications toward advancement to Platinum or Diamond level in the OPN Specialized program. Oracle Exastack Labs and ISV Enablement: Dedicated Oracle Exastack lab environments and related technical enablement resources (including Guided Learning Paths and Boot Camps) will be available through OPN for OPN members to further their knowledge of Oracle Exastack offerings, and qualify their applications for Oracle Exastack Optimized or Oracle Exastack Ready. Oracle Exastack labs will be available to qualifying OPN members at the Gold level or above. Partners are eligible to participate in the Oracle Exastack Ready program immediately, which will help them meet the requirements to attain Oracle Exastack Optimized status in the future. Guidelines for Oracle Exastack Optimized, as well as Oracle Exastack Labs will be available in fall 2011. Supporting Quotes "In order to effectively differentiate their software applications in the marketplace, ISVs need to rapidly deliver new capabilities and performance improvements," said Judson Althoff, Oracle senior vice president of Worldwide Alliances and Channels and Embedded Sales. "With Oracle Exastack, ISVs have the ability to optimize and deploy their applications with a complete, integrated and cloud-ready infrastructure that will help them accelerate innovation, unlock new features and functionality, and deliver superior value to customers." "We view performance as absolutely critical and a key differentiator," said Tom Stock, SVP of Product Management, GoldenSource. "As a leading provider of enterprise data management solutions for securities and investment management firms, with Oracle Exadata Database Machine, we see an opportunity to notably improve data processing performance -- providing high quality 'golden copy' data in a reduced timeframe. Achieving Oracle Exastack Optimized status will be a stamp of approval that our solution will provide the performance and scalability that our customers demand." "As a leading provider of Revenue Intelligence solutions for telecommunications, media and entertainment service providers, our customers continually demand more readily accessible, enriched and pre-analyzed information to minimize their financial risks and maximize their margins," said Alon Aginsky, President and CEO of cVidya Networks. "Oracle Exastack enables our solutions to deliver the power, infrastructure, and innovation required to transform our customers' business operations and stay ahead of the game." Supporting Resources Oracle PartnerNetwork (OPN) Oracle Exastack Oracle Exastack Datasheet Judson Althoff blog Connect with the Oracle Partner community at OPN on Facebook, OPN on LinkedIn, OPN on YouTube, or OPN on Twitter

Read the article

Importing Multiple Schemas to a Model in Oracle SQL Developer Data Modeler

- by thatjeffsmith

Your physical data model might stretch across multiple Oracle schemas. Or maybe you just want a single diagram containing tables, views, etc. spanning more than a single user in the database. The process for importing a data dictionary is the same, regardless if you want to suck in objects from one schema, or many schemas. Let’s take a quick look at how to get started with a data dictionary import. I’m using Oracle SQL Developer in this example. The process is nearly identical in Oracle SQL Developer Data Modeler – the only difference being you’ll use the ‘File’ menu to get started versus the ‘File – Data Modeler’ menu in SQL Developer. Remember, the functionality is exactly the same whether you use SQL Developer or SQL Developer Data Modeler when it comes to the data modeling features – you’ll just have a cleaner user interface in SQL Developer Data Modeler. Importing a Data Dictionary to a Model You’ll want to open or create your model first. You can import objects to an existing or new model. The easiest way to get started is to simply open the ‘Browser’ under the View menu. The Browser allows you to navigate your open designs/models You’ll see an ‘Untitled_1′ model by default. I’ve renamed mine to ‘hr_sh_scott_demo.’ Now go back to the File menu, and expand the ‘Data Modeler’ section, and select ‘Import – Data Dictionary.’ This is a fancy way of saying, ‘suck objects out of the database into my model’ Connect! If you haven’t already defined a connection to the database you want to reverse engineer, you’ll need to do that now. I’m going to assume you already have that connection – so select it, and hit the ‘Next’ button. Select the Schema(s) to be imported Select one or more schemas you want to import The schemas selected on this page of the wizard will dictate the lists of tables, views, synonyms, and everything else you can choose from in the next wizard step to import. For brevity, I have selected ALL tables, views, and synonyms from 3 different schemas: HR SCOTT SH Once I hit the ‘Finish’ button in the wizard, SQL Developer will interrogate the database and add the objects to our model. The Big Model and the 3 Little Models I can now see ALL of the objects I just imported in the ‘hr_sh_scott_demo’ relational model in my design tree, and in my relational diagram. Quick Tip: Oracle SQL Developer calls what most folks think of as a ‘Physical Model’ the ‘Relational Model.’ Same difference, mostly. In SQL Developer, a Physical model allows you to define partitioning schemes, advanced storage parameters, and add your PL/SQL code. You can have multiple physical models per relational models. For example I might have a 4 Node RAC in Production that uses partitioning, but in test/dev, only have a single instance with no partitioning. I can have models for both of those physical implementations. The list of tables in my relational model Wouldn’t it be nice if I could segregate the objects based on their schema? Good news, you can! And it’s done by default Several of you might already know where I’m going with this – SUBVIEWS. You can easily create a ‘SubView’ by selecting one or more objects in your model or diagram and add them to a new SubView. SubViews are just mini-models. They contain a subset of objects from the main model. This is very handy when you want to break your model into smaller, more digestible parts. The model information is identical across the model and subviews, so you don’t have to worry about making a change in one place and not having it propagate across your design. SubViews can be used as filters when you create reports and exports as well. So instead of generating a PDF for everything, just show me what’s in my ‘ABC’ subview. But, I don’t want to do any work! Remember, I’m really lazy. More good news – it’s already done by default! The schemas are automatically used to create default SubViews Auto-Navigate to the Object in the Diagram In the subview tree node, right-click on the object you want to navigate to. You can ask to be taken to the main model view or to the SubView location. If you haven’t already opened the SubView in the diagram, it will be automatically opened for you. The SubView diagram only contains the objects from that SubView Your SubView might still be pretty big, many dozens of objects, so don’t forget about the ‘Navigator‘ either! In summary, use the ‘Import’ feature to add existing database objects to your model. If you import from multiple schemas, take advantage of the default schema based SubViews to help you manage your models! Sometimes less is more!

Read the article

ASP.NET MVC Custom Profile Provider

- by Ben Griswold

It’s been a long while since I last used the ASP.NET Profile provider. It’s a shame, too, because it just works with very little development effort: Membership tables installed? Check. Profile enabled in web.config? Check. SqlProfileProvider connection string set? Check. Profile properties defined in said web.config file? Check. Write code to set value, read value, build and test. Check. Check. Check. Yep, I thought the built-in Profile stuff was pure gold until I noticed how the user-based information is persisted to the database. It’s stored as xml and, well, that was going to be trouble if I ever wanted to query the profile data. So, I have avoided the super-easy-to-use ASP.NET Profile provider ever since, until this week, when I decided I could use it to store user-specific properties which I am 99% positive I’ll never need to query against ever. I opened up my ASP.NET MVC application, completed steps 1-4 (above) in about 3 minutes, started writing my profile get/set code and that’s where the plan broke down. Oh yeah. That’s right. Visual Studio auto-generates a strongly-type Profile reference for web site projects but not for ASP.NET MVC or Web Applications. Bummer. So, I went through the steps of getting a customer profile provider working in my ASP.NET MVC application: First, I defined a CurrentUser routine and my profile properties in a custom Profile class like so: using System.Web.Profile; using System.Web.Security; using Project.Core; namespace Project.Web.Context { public class MemberPreferencesProfile : ProfileBase { static public MemberPreferencesProfile CurrentUser { get { return (MemberPreferencesProfile) Create(Membership.GetUser().UserName); } } public Enums.PresenceViewModes? ViewMode { get { return ((Enums.PresenceViewModes) ( base["ViewMode"] ?? Enums.PresenceViewModes.Category)); } set { base["ViewMode"] = value; Save(); } } } } And then I replaced the existing profile configuration web.config with the following: <profile enabled="true" defaultProvider="MvcSqlProfileProvider" inherits="Project.Web.Context.MemberPreferencesProfile"> <providers> <clear/> <add name="MvcSqlProfileProvider" type="System.Web.Profile.SqlProfileProvider, System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" connectionStringName="ApplicationServices" applicationName="/"/> </providers> </profile> Notice that profile is enabled, I’ve defined the defaultProvider and profile is now inheriting from my custom MemberPreferencesProfile class. Finally, I am now able to set and get profile property values nearly the same way as I did with website projects: viewMode = MemberPreferencesProfile.CurrentUser.ViewMode; MemberPreferencesProfile.CurrentUser.ViewMode = viewMode;

Read the article

Java Embedded @ JavaOne: Q & A

- by terrencebarr

There has been a lot of interest in Java Embedded @ JavaOne since it was announced a short while ago (see my previous post). As this is a new conference we did get a number of questions regarding the conference. So we put together a brief Q & A on audience focus, dates, registrations, pricing, submissions, etc. Hope this helps and, remember, the Call for Papers ends next week, Jul 18th 2012! Cheers, – Terrence Java Embedded @ JavaOne : Q & A Q. Where can I learn more about “Java Embedded @ JavaOne”? A. Please visit: http://oracle.com/javaone/embedded Q. What is the purpose of “Java Embedded @ JavaOne”? A. This net-new event is designed to provide business and technical decision makers, as well as Java embedded ecosystem partners, a unique occasion to come together and learn about how they can use Java Embedded technologies for new business opportunities. Q. What broad audiences would benefit by attending “Java Embedded @ JavaOne”? A. Java licensees; Government agencies; ISVs, Device Manufacturers; Service Providers such as Telcos, Utilities, Healthcare, Energy, Smart Grid/Smart Metering; Automotive/Telematics; Home/Building Automation; Factory Automation; Media/TV; and Payment vendors. Q. What business titles would benefit by attending “Java Embedded @ JavaOne”? A. The ideal audience for this event is business and technical decision makers (e.g. System Integrators, CTO, CXO, Chief Architects/Architects, Business Development Managers, Project Managers, Purchasing managers, Technical Leads, Senior Decision Makers, Practice Leads, R&D Heads, and Development Managers/Leads). Q. When is “Java Embedded @ JavaOne” taking place? A. The event takes place on Wednesday, Oct. 3th through Thursday, Oct. 4th. Q. Where is “Java Embedded @ JavaOne” taking place? A. The event takes place in the Hotel Nikko. Q. Won’t “Java Embedded @ JavaOne” impact the flagship JavaOne conference since the Hotel Nikko is one of the 3 flagship JavaOne conference’s venue hotels? A. No. Separate space in the Hotel Nikko will be used for “Java Embedded @ JavaOne” and will in no way impact scale and scope of the flagship JavaOne conference’s content mix. Q. Will there be a call for papers for “Java Embedded @ JavaOne”? A. Yes. The call for papers has started but is ONLY for business focused submissions. Q. What type of business submissions can I make for “Java Embedded @ JavaOne”? A. We are accepting 3 types of business submissions: Best Practices: Java Embedded business solutions, methods, and techniques that consistently show results superior to those achieved with other means, as well as discussions on how Java Embedded can improve business operations, and increase competitive differentiation and profitability. Case Studies: Discussions with Oracle customers and partners that describe the unique business drivers that convinced them to implement Java Embedded as part of an infrastructure technology mix. The discussions will highlight the issues they faced, the decision making involved, and the implementation choices made to create value and improve business differentiation. Panel: Moderator-driven open discussion focused on the emerging opportunities Java Embedded offers businesses, as well as other topics such as strategy, overcoming common challenges, etc. Q. What is the call for papers timeline for “Java Embedded @ JavaOne”? A. The timeline is as follows: CFP Launched – June 18th Deadline for submissions – July 18th Notifications (Accepts/Declines) – week of July 29th Deadline for speakers to accept speaker invitation – August 10th Presentations due for review – August 31st Q. Where can I find more call for paper details for “Java Embedded @ JavaOne”? A. Please go to: http://www.oracle.com/javaone/embedded/call-for-papers/information/index.html Q. How much does it cost to attend “Java Embedded @ JavaOne”? A. The cost to attend is: $595.00 U.S. — Early Bird (Launch date – July 13, 2012) $795.00 U.S. — Pre-Registration (July 14 – September 28, 2012) $995.00 U.S. — Onsite Registration (September 29 – October 4, 2012) Q. Can an attendee of the flagship JavaOne event and Oracle OpenWorld attend “Java Embedded @ JavaOne”? ?A. Yes. Attendees of both the flagship JavaOne event and Oracle OpenWorld can attend “Java Embedded @ JavaOne” by purchasing a $100.00 U.S. upgrade to their full conference pass. Filed under: Mobile & Embedded Tagged: Call for Papers, Java Embedded @ JavaOne, JavaOne San Francisco

Read the article

MySQL 5.5 - Lost connection to MySQL server during query

- by bully

I have an Ubuntu 12.04 LTS server running at a german hoster (virtualized system). # uname -a Linux ... 3.2.0-27-generic #43-Ubuntu SMP Fri Jul 6 14:25:57 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I want to migrate a Web CMS system, called Contao. It's not my first migration, but my first migration having connection issues with mysql. Migration went successfully, I have the same Contao version running (it's more or less just copy / paste). For the database behind, I did: apt-get install mysql-server phpmyadmin I set a root password and added a user for the CMS which has enough rights on its own database (and only its database) for doing the stuff it has to do. Data import via phpmyadmin worked just fine. I can access the backend of the CMS (which needs to deal with the database already). If I try to access the frontend now, I get the following error: Fatal error: Uncaught exception Exception with message Query error: Lost connection to MySQL server during query (<query statement here, nothing special, just a select>) thrown in /var/www/system/libraries/Database.php on line 686 (Keep in mind: I can access mysql with phpmyadmin and through the backend, working like a charme, it's just the frontend call causing errors). If I spam F5 in my browser I can sometimes even kill the mysql deamon. If I run # mysqld --log-warnings=2 I get this: ... 120921 7:57:31 [Note] mysqld: ready for connections. Version: '5.5.24-0ubuntu0.12.04.1' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 05:57:37 UTC - mysqld got signal 4 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=151 thread_count=1 connection_count=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 346679 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. Thread pointer: 0x7f1485db3b20 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 7f1480041e60 thread_stack 0x30000 mysqld(my_print_stacktrace+0x29)[0x7f1483b96459] mysqld(handle_fatal_signal+0x483)[0x7f1483a5c1d3] /lib/x86_64-linux-gnu/libpthread.so.0(+0xfcb0)[0x7f1482797cb0] /lib/x86_64-linux-gnu/libm.so.6(+0x42e11)[0x7f14821cae11] mysqld(_ZN10SQL_SELECT17test_quick_selectEP3THD6BitmapILj64EEyyb+0x1368)[0x7f1483b26cb8] mysqld(+0x33116a)[0x7f148397916a] mysqld(_ZN4JOIN8optimizeEv+0x558)[0x7f148397d3e8] mysqld(_Z12mysql_selectP3THDPPP4ItemP10TABLE_LISTjR4ListIS1_ES2_jP8st_orderSB_S2_SB_yP13select_resultP18st_select_lex_unitP13st_select_lex+0xdd)[0x7f148397fd7d] mysqld(_Z13handle_selectP3THDP3LEXP13select_resultm+0x17c)[0x7f1483985d2c] mysqld(+0x2f4524)[0x7f148393c524] mysqld(_Z21mysql_execute_commandP3THD+0x293e)[0x7f14839451de] mysqld(_Z11mysql_parseP3THDPcjP12Parser_state+0x10f)[0x7f1483948bef] mysqld(_Z16dispatch_command19enum_server_commandP3THDPcj+0x1365)[0x7f148394a025] mysqld(_Z24do_handle_one_connectionP3THD+0x1bd)[0x7f14839ec7cd] mysqld(handle_one_connection+0x50)[0x7f14839ec830] /lib/x86_64-linux-gnu/libpthread.so.0(+0x7e9a)[0x7f148278fe9a] /lib/x86_64-linux-gnu/libc.so.6(clone+0x6d)[0x7f1481eba4bd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort. Query (7f1464004b60): is an invalid pointer Connection ID (thread ID): 1 Status: NOT_KILLED From /var/log/syslog: Sep 21 07:17:01 s16477249 CRON[23855]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Sep 21 07:18:51 s16477249 kernel: [231923.349159] type=1400 audit(1348204731.333:70): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=23946 comm="apparmor_parser" Sep 21 07:18:53 s16477249 /etc/mysql/debian-start[23990]: Upgrading MySQL tables if necessary. Sep 21 07:18:53 s16477249 /etc/mysql/debian-start[23993]: /usr/bin/mysql_upgrade: the '--basedir' option is always ignored Sep 21 07:18:53 s16477249 /etc/mysql/debian-start[23993]: Looking for 'mysql' as: /usr/bin/mysql Sep 21 07:18:53 s16477249 /etc/mysql/debian-start[23993]: Looking for 'mysqlcheck' as: /usr/bin/mysqlcheck Sep 21 07:18:53 s16477249 /etc/mysql/debian-start[23993]: This installation of MySQL is already upgraded to 5.5.24, use --force if you still need to run mysql_upgrade Sep 21 07:18:53 s16477249 /etc/mysql/debian-start[24004]: Checking for insecure root accounts. Sep 21 07:18:53 s16477249 /etc/mysql/debian-start[24009]: Triggering myisam-recover for all MyISAM tables I'm using MyISAM tables all over, nothing with InnoDB there. Starting / stopping mysql is done via sudo service mysql start sudo service mysql stop After using google a little bit, I experimented a little bit with timeouts, correct socket path in the /etc/mysql/my.cnf file, but nothing helped. There are some old (from 2008) Gentoo bugs, where re-compiling just solved the problem. I already re-installed mysql via: sudo apt-get remove mysql-server mysql-common sudo apt-get autoremove sudo apt-get install mysql-server without any results. This is the first time I'm running into this problem, and I'm not very experienced with this kind of mysql 'administration'. So mainly, I want to know if anyone of you could help me out please :) Is it a mysql bug? Is something broken in the Ubuntu repositories? Is this one of those misterious 'use-tcp-connection-instead-of-socket-stuff-because-there-are-problems-on-virtualized-machines-with-sockets'-problem? Or am I completly on the wrong way and I just miss-configured something? Remember, phpmyadmin and access to the backend (which uses the database, too) is just fine. Maybe something with Apache? What can I do? Any help is appreciated, so thanks in advance :)

Read the article

Developer Training – Various Options for Maximum Benefit – Part 4

- by pinaldave

Developer Training - Importance and Significance - Part 1 Developer Training – Employee Morals and Ethics – Part 2 Developer Training – Difficult Questions and Alternative Perspective - Part 3 Developer Training – Various Options for Developer Training – Part 4 Developer Training – A Conclusive Summary- Part 5 If you have been reading this series, by now you are aware of all the pros and cons that can come along with training. We’ve asked and answered hard questions, and investigated them “whys” and “hows” of training. Now it is time to talk about all the different kinds of training that are out there! On Job Training The most common type of training is on the job training. Everyone receives this kind of education – even experts who come in to consult have to be taught where the printer, pens, and copy machines are. If you are thinking about more concrete topics, though, on the job training can be some of the easiest to come across. Picture this: someone in the company whom you really admire is hard at work on a project. You come up to them and ask to help them out – if they are a busy developer, the odds are that they will say “yes, please!” If you phrase your question as an offer of help, you can receive training without ever putting someone in the awkward position of acting as a mentor. However, some people may want the task of being a mentor. It can never hurt to ask. Most people will be more than willing to pass their knowledge along. Extreme Programming If your company and coworkers are willing, you can even investigate Extreme Programming. This is a type of programming that allows small teams to quickly develop code and products that are released with almost immediate user feedback. You can find more information at http://www.extremeprogramming.org/. If this is something your company could use, suggest it to your supervisor. Even if they say no, it will make it clear that you are a go-getter who is interested in new and exciting projects. If the answer is yes, then you have the opportunity to get some of the best on the job training around. In Person Training Click on Image to Enlarge When you say the word “training,” most people’s minds go back to the classroom, an image they are familiar with. While training doesn’t always have to be in a traditional setting, because it is so familiar it can also be the most valuable type of training. There are many ways to get training through a live instructor. Some companies may be willing to send a representative to you, where employees will get training, sometimes food and coffee, and a live instructor who can answer questions immediately. Sometimes these trainers are also able to do consultations at the same time, which can invaluable to a company. If you are the one to asks your supervisor for a training session that can also be turned into a consultation, you may stick in their minds as an incredibly dedicated employee. If you can’t find a representative, local colleges can also be a good resource for free or cheap classes – or they may have representatives coming who are willing to take on a few more students. Benefits of On Demand Developer Training Of course, you can often get the best of all these types of training with online or On Demand training. You can get the benefit of a live instructor who is willing to answer questions (although in this case, usually through e-mail or other online venues), there are often real-world examples to follow along – like on the job training – and best of all you can learn whenever you have the time or need. Did a problem with your server come up at midnight when all your supervisors are safe at home and probably in bed? No problem! On Demand training is especially useful if you need to slow down, pause, or rewind a training session. Not even a real-life instructor can do that! When I was writing this blog post, I felt that each of the subject, which I have covered can be blog posts of itself. However, I wanted to keep the the blog post concise and so touch based on three major training aspects 1) On Job Training 2) In Person Training and 3) Online training. Here is the question for you – is there any other kind of training methods available, which are effective and one should consider it? If yes, what are those, I may write a follow up blog post on the same subject next week. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Developer Training, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

Read the article

Installing Matlab on ubuntu 12.04 32 bits

- by Amir

I have been trying to install Matlab2012a, matlab2012b and Matlab2013a for like 4 hours, triedto fix my prospective errors regarding the posts 2012a, Ubuntu-Matlab Documentation and Matlab-central. But either i am recieving an error while the installation GUI pops-up with the error : The application encountered an unexpected error and needs to close. You may want to try re-installing your product(s). More information can be found at /tmp/mathworks_amir.log On the other hand for 2012a. and the errors for 2012b and 2013a is : `Installing ... Exception in thread "main" com.google.inject.ProvisionException: Guice provision errors: 1) Error in custom provider, java.lang.RuntimeException: java.lang.reflect.InvocationTargetException at com.mathworks.wizard.WizardModule.provideDisplayProperties(WizardModule.java:60) while locating com.mathworks.instutil.DisplayProperties at com.mathworks.wizard.ui.components.ComponentsModule.providePaintStrategy(ComponentsModule.java:76) while locating com.mathworks.wizard.ui.components.PaintStrategy for parameter 4 at com.mathworks.wizard.ui.components.SwingComponentFactoryImpl.(SwingComponentFactoryImpl.java:110) while locating com.mathworks.wizard.ui.components.SwingComponentFactoryImpl while locating com.mathworks.wizard.ui.components.SwingComponentFactory for parameter 1 at com.mathworks.wizard.ui.WizardUIImpl.(WizardUIImpl.java:65) while locating com.mathworks.wizard.ui.WizardUIImpl while locating com.mathworks.wizard.ui.WizardUI annotated with @com.google.inject.name.Named(value=BaseWizardUI) at com.mathworks.wizard.ui.UIModule.provideWizardUI(UIModule.java:50) while locating com.mathworks.wizard.ui.WizardUI for parameter 0 at com.mathworks.wizard.ExceptionHandlerImpl.(ExceptionHandlerImpl.java:22) while locating com.mathworks.wizard.ExceptionHandlerImpl while locating com.mathworks.wizard.ExceptionHandler 1 error at com.google.inject.InjectorImpl$4.get(InjectorImpl.java:767) at com.google.inject.InjectorImpl.getInstance(InjectorImpl.java:793) at com.mathworks.wizard.WizardLauncher.startWizard(WizardLauncher.java:160) at com.mathworks.wizard.WizardLauncher.start(WizardLauncher.java:75) at com.mathworks.wizard.AbstractLauncher.launch(AbstractLauncher.java:27) at com.mathworks.wizard.AbstractLauncher.launchStandalone(AbstractLauncher.java:18) at com.mathworks.professionalinstaller.Launcher.main(Launcher.java:21) Caused by: java.lang.RuntimeException: java.lang.reflect.InvocationTargetException at com.google.inject.internal.ProviderMethod.get(ProviderMethod.java:106) at com.google.inject.InternalFactoryToProviderAdapter.get(InternalFactoryToProviderAdapter.java:48) at com.google.inject.InjectorImpl$4$1.call(InjectorImpl.java:758) at com.google.inject.InjectorImpl.callInContext(InjectorImpl.java:811) at com.google.inject.InjectorImpl$4.get(InjectorImpl.java:754) at com.google.inject.spi.ProviderLookup$1.get(ProviderLookup.java:89) at com.google.inject.spi.ProviderLookup$1.get(ProviderLookup.java:89) at com.google.inject.internal.ProviderMethod.get(ProviderMethod.java:95) at com.google.inject.InternalFactoryToProviderAdapter.get(InternalFactoryToProviderAdapter.java:48) at com.google.inject.SingleParameterInjector.inject(SingleParameterInjector.java:42) at com.google.inject.SingleParameterInjector.getAll(SingleParameterInjector.java:66) at com.google.inject.ConstructorInjector.construct(ConstructorInjector.java:84) at com.google.inject.ConstructorBindingImpl$Factory.get(ConstructorBindingImpl.java:111) at com.google.inject.FactoryProxy.get(FactoryProxy.java:56) at com.google.inject.SingleParameterInjector.inject(SingleParameterInjector.java:42) at com.google.inject.SingleParameterInjector.getAll(SingleParameterInjector.java:66) at com.google.inject.ConstructorInjector.construct(ConstructorInjector.java:84) at com.google.inject.ConstructorBindingImpl$Factory.get(ConstructorBindingImpl.java:111) at com.google.inject.FactoryProxy.get(FactoryProxy.java:56) at com.google.inject.ProviderToInternalFactoryAdapter$1.call(ProviderToInternalFactoryAdapter.java:45) at com.google.inject.InjectorImpl.callInContext(InjectorImpl.java:811) at com.google.inject.ProviderToInternalFactoryAdapter.get(ProviderToInternalFactoryAdapter.java:42) at com.google.inject.Scopes$1$1.get(Scopes.java:54) at com.google.inject.InternalFactoryToProviderAdapter.get(InternalFactoryToProviderAdapter.java:48) at com.google.inject.InjectorImpl$4$1.call(InjectorImpl.java:758) at com.google.inject.InjectorImpl.callInContext(InjectorImpl.java:811) at com.google.inject.InjectorImpl$4.get(InjectorImpl.java:754) at com.google.inject.spi.ProviderLookup$1.get(ProviderLookup.java:89) at com.google.inject.spi.ProviderLookup$1.get(ProviderLookup.java:89) at com.google.inject.internal.ProviderMethod.get(ProviderMethod.java:95) at com.google.inject.InternalFactoryToProviderAdapter.get(InternalFactoryToProviderAdapter.java:48) at com.google.inject.ProviderToInternalFactoryAdapter$1.call(ProviderToInternalFactoryAdapter.java:45) at com.google.inject.InjectorImpl.callInContext(InjectorImpl.java:811) at com.google.inject.ProviderToInternalFactoryAdapter.get(ProviderToInternalFactoryAdapter.java:42) at com.google.inject.Scopes$1$1.get(Scopes.java:54) at com.google.inject.InternalFactoryToProviderAdapter.get(InternalFactoryToProviderAdapter.java:48) at com.google.inject.SingleParameterInjector.inject(SingleParameterInjector.java:42) at com.google.inject.SingleParameterInjector.getAll(SingleParameterInjector.java:66) at com.google.inject.ConstructorInjector.construct(ConstructorInjector.java:84) at com.google.inject.ConstructorBindingImpl$Factory.get(ConstructorBindingImpl.java:111) at com.google.inject.FactoryProxy.get(FactoryProxy.java:56) at com.google.inject.ProviderToInternalFactoryAdapter$1.call(ProviderToInternalFactoryAdapter.java:45) at com.google.inject.InjectorImpl.callInContext(InjectorImpl.java:811) at com.google.inject.ProviderToInternalFactoryAdapter.get(ProviderToInternalFactoryAdapter.java:42) at com.google.inject.Scopes$1$1.get(Scopes.java:54) at com.google.inject.InternalFactoryToProviderAdapter.get(InternalFactoryToProviderAdapter.java:48) at com.google.inject.InjectorImpl$4$1.call(InjectorImpl.java:758) at com.google.inject.InjectorImpl.callInContext(InjectorImpl.java:804) at com.google.inject.InjectorImpl$4.get(InjectorImpl.java:754) ... 6 more Caused by: java.lang.reflect.InvocationTargetException at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:606) at com.google.inject.internal.ProviderMethod.get(ProviderMethod.java:101) ... 54 more Caused by: com.mathworks.instutil.JNIException: java.lang.UnsatisfiedLinkError: Can't load library: /tmp/mathworks_7417/bin/glnxa64/libinstutil.so at com.mathworks.instutil.NativeUtility.loadNativeLibrary(NativeUtility.java:39) at com.mathworks.instutil.NativeUtility.(NativeUtility.java:24) at com.mathworks.instutil.DisplayPropertiesImpl.(DisplayPropertiesImpl.java:10) at com.mathworks.wizard.WizardModule.provideDisplayProperties(WizardModule.java:67) ... 59 more Caused by: java.lang.UnsatisfiedLinkError: Can't load library: /tmp/mathworks_7417/bin/glnxa64/libinstutil.so at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1842) at java.lang.Runtime.load0(Runtime.java:795) at java.lang.System.load(System.java:1061) at com.mathworks.instutil.NativeUtility.loadNativeLibrary(NativeUtility.java:37) ... 62 more Finished ` I have tried to 1- re-install java run-time 6 and then 7. 2- pass the java-path to the install with : -javadir 3- use the force to install on 32 bits as : sh install -glnx86 -v -javadir /usr/lib/jvm/java-7-openjdk-i386/jre But it seems none of them have worked so far. any ideas ??

Read the article

UCM 11g is 4 days old!

- by kyle.hatlestad

Ok...so I missed posting a blog entry when UCM 11g and the entire ECM suite released on Tuesday. Hopefully you've already seen the announcements on any number of the Oracle ECM blogs out there such as ECM Alerts, Fusion ECM, bex huff, or C4. So I won't bore you with the same talking points like 179 million check-ins per day or 124 web site page hits per second. Instead, I thought I'd show some screenshots of the new features in UCM and URM 11g. WebLogic Server and Enterprise Manager So probably the biggest change in 11g is UCM and URM now run on top of the WebLogic Server application server. This is a huge step as ECM is now on a standard platform with the rest of Oracle Fusion Middleware which makes installation, configuration, and integration consistent among all the products. From a feature perspective, it's also beneficial because it's now integrated with Oracle Enterprise Manager. Enterprise Manager provides a lot of provisioning control over servers as well as performance monitoring and access to logs and debugging information. Desktop Integration Suite Desktop Integration Suite got a complete overhaul for 11g. It exposes a lot more features within Windows Explorer such as saved searches, workflow queue, and checked-out items. It also now support metadata pop-up screens to let users fill in additional metadata when they drag-n-drop files in! And the integration within Office applications has changed significantly by introducing a dedicated UCM menu to do open, save, compare, etc. Site Studio for External Applications In UCM Site Studio 10gR4, a major architectural shift was introduced which brought several new objects such as elements, region definitions, region templates, and placeholder definitions. This truly separated the content from the display and from the definition. It also allowed separation of the content from needing to be rendered on a complete Site Studio page. Well, the new Site Studio for External Applications takes advantage of that architecture and introduces pre-built tags and plug-ins to JDeveloper to allow to go from simply adding a content area to your web application page to building an entire web site, just like you would have done in Site Studio Designer. In addition to these changes, enhancements to the core Site Studio have been added as well. One of the big ones is called Designer Mode which allows power-users to bypass the standard rules defined by the placeholder definition or template and perform any number of additional actions. This reduces the need to go back to Site Studio Designer or JDeveloper to make more advanced changes to the site. Dashboards As part of the updated records management functionality in both UCM and URM, users can now set a dashboard view on their home page to surface common functions in a single view. It has pre-built "portlets" users can choose from to display and organize they way they want. Behind the scenes, these dashboards are stored as Content Folios. So the dashboards themselves are content items that can be revisioned and shared between users. And new dashboard portlets can be easily added (like the User Profile one in the screenshots) by getting a copy of an existing one, modifying the display, and then checking it in as a new one to select from. URM Interface Enhancements URM includes several new UI and usability enhancements in 11g. There is a new view for physical records, a place to configure "favorite" items to quickly get to, and new placement of the records management menu. BI Publisher Reports Records management in UCM and URM now offer reports generated through embedded BI Publisher. Templates are controlled by rich text files checked directly into the repository, so they can be easily modified. Other Features A new Inbound Refinery conversion option is available that does native Microsoft Office HTML conversion. If your IBR is on Windows and you have the native applications loaded, the IBR can use them to produce HTML. A new GUI template editor for Dynamic Converter is available. It's written in Java so is available through all the supported browsers and platforms. The original ActiveX based editor is also still available. The Component Manager interface has changed to help provide an easier and more descriptive way to enable core components that are installed along with UCM. All of the supported components are immediately available to turn on and do not have to be installed separately as in previous versions. My Downloads is located in the My Content Server menu and provides for easy download of client installs including Desktop Integration Suite and Site Studio Designer. Well, hopefully that gives you a taste for some of the new things in 11g. We're all pretty excited here at Oracle about all the new changes and enhancements. Over the next few months I hope to highlight some of these features more in-depth, so keep your eye out for those posts.

Read the article

How TiVo is messing up customer support.

- by James Fleming

Ok, So I've gotten a TiVo and overall, I'm happy, but there have been issues and I suspect I've a defective unit. - Now the nice folks after many service calls were happy to swap it out, and to ensure continuity of service, they sent me a new unit (after a $109 deposit). That was yesterday. Today, when we go to watch a little TV, and wait for our replacement unit to arrive we find our TiVo service has been suspended. WTF? They have an exchange program, but your unit your waiting to exchange is as dead as a doornail until the replacement arrives. How hard is it to keep the old unit active for an extra week? Here is the exchange w/Tivo below... You are currently number 1 in the queue. We apologize for the delay. We will assign you to an agent as soon as one is available.The average amount of time a customer has to wait is 00:13. Kaylene (Listening) Kaylene: Thank you for contacting TiVo! My name is Kaylene. So that I may better assist you, are you an existing customer? james Fleming: yes I am, but I'm now having second thoughts about being one Kaylene: Thank you for verifying your information. How may I assist you today James? james Fleming: I've been having issues w/a tivo box & I'm getting a replacement sent out to me (after paying an additional deposit) and now my current unit is no longer activated Kaylene: I can help you today! Kaylene: When we process an exchange we do transfer over the service to the replacement box so it is active and ready to go when you receive it. james Fleming: which is to say you also make my current box worthless until such time I receive a new box?!?!? Kaylene: I apologize that your original box was deactivated so we could activate your replacement box. james Fleming: Why on Earth would I bother to pay in advance for a new box if you were going to kill my existing box. Kaylene: What features are you needing to use on your current box? james Fleming: I need to be able to access my netflix subscription (if I'm lucky enough to have it work without rebooting) Kaylene: Can I have you verify the TiVo Service Number of your TiVo box please? james Fleming: 7460011906979b4 Kaylene: We have your current box temporary service but not all features are available with temporary service as it is not paid for service. Kaylene: If you like I can transfer your service back to your current box for now. Then once you receive the new box you will have to call in and have the service transferred back to the new box. james Fleming: Not paid for? Let's see> one tivo box + 3 year service plan + monthly service + $109 deposit on a second box = what? Kaylene: Would you like me to transfer your service back to your current box? james Fleming: Yes - that would be helpful Kaylene: All you will need to do is contact us again once you receive the new box so we can transfer it back. Kaylene: I have put your service back on TiVo box 7460011906979b4. james Fleming: What would also be helpful is your firm informing me to how you'd be cutting service in the interim. james Fleming: Again - I opted to pay to have a second box delivered BEFORE returning the box I have - thus trying to have a continuity of service.. Kaylene: This is not something we normally do so it is important when you contact us to transfer the service back to the new box when you receive it that you reference this case number: 110622-006089. Kaylene: I apologize about the inconvenience. You may need force a few connections for the box to recognize the service again. james Fleming: If it's not something you normally do than WHY would you have a $109 fee and a term for the service. james Fleming: I am not mad at you, but your company is not impressing me and I'm blogging about this experience Kaylene: Again I apologize about the inconvenience but you should be good to go now. Is there anything else I can help you with today? james Fleming: so I need to go through the re-actviate process or is that somethign you do Kaylene: When you receive the new TiVo box you need to contact us so we can transfer the service to the new box for you. james Fleming: sure Kaylene: Is there anything else I can help you with today James? james Fleming: Nope - please email this transcript to me Kaylene: I apologize but we do not have the ability to e-mail you a copy of this transcript. You can view it online at http://www.tivo.com when you sign into your account or you can copy and paste it now to save it. Kaylene: Thank you for contacting TiVo today. Your reference number for our conversation is 110622-006089. You can save this for your records, and if necessary, provide this to a later agent to pull up what we discussed. There will be a brief satisfaction survey emailed to you. We would appreciate any feedback on your TiVo Chat Support experience today. Kaylene: Thank you for using TiVo Chat and have a great day James! Good-bye. Kaylene has disconnected.

Search Results

Search found 24931 results on 998 pages for 'information visualization'.

Page 900/998 | < Previous Page | 896 897 898 899 900 901 902 903 904 905 906 907 | Next Page >

- by user109717

- by Nick

- by Expo_Rob

- by David Dorf

- by eJugnoo

- by Ben Griswold

- by Jakob Ehn

- by Chris Hoffman

- by srkirkland

- by GeekAgilistMercenary

- by Jason Fitzpatrick

- by dPEN

- by Matthew Guay

- by John-Brown.Evans

- by Derek Meier

- by Christian

- by pfolgado

- by thatjeffsmith

- by Ben Griswold

- by terrencebarr

- by bully

- by pinaldave

- by Amir

- by kyle.hatlestad

- by James Fleming

< Previous Page | 896 897 898 899 900 901 902 903 904 905 906 907 | Next Page >