Search Results

Search found 27606 results on 1105 pages for 'javascript disabled'.

Page 908/1105 | < Previous Page | 904 905 906 907 908 909 910 911 912 913 914 915  | Next Page >

  • Nvidia GT218 repository drivers don't work

    - by user1042840
    I upgraded all packages with sudo apt-get upgrade command on my Ubuntu 10.04 box and I have Ubuntu 12.04 3.2.0-29-generic-pae now. I have two monitors and the following GPU: 01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [NVS 300] (rev a2) After upgrading to 12.04, I somehow lost my previous setup with one common workspace stretched across two monitors. When Ubuntu starts only one monitor is on. I can see the message on the active monitor: Not optimum mode. Recommended mode: 1680x1050 60Hz I used Nvidia proprietary drivers on 10.04 but now jockey-text --list shows: xorg:nvidia_current - NVIDIA accelerated graphics driver (Proprietary, Disabled, Not in use) xorg:nvidia_current_updates - NVIDIA accelerated graphics driver (post-release updates) (Proprietary, Enabled, Not in use) When I run sudo nvidia-settings it says You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.' I typed nvidia-xconfig and rebooted, but jockey-text --list says the same after the reboot: Not in use. The same with nvidia-current - Enabled but Not in use. I also tried nvidia-173 but I ended up in tty immediately at startup so I removed it. I used to have some problems with Nvidia proprietary drivers on 10.04, I had to put paths to EDID files in /etc/X11/xorg.conf explicitly, but the resolution was as recommended and both monitors were working. If I understand correctly, nouveau drivers are used now by default because the resolution is still quite high, definitely not 800x600, xrandr showed: xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 400, current 1600 x 1200, maximum 1600 x 1200 default connected 1600x1200+0+0 0mm x 0mm 1600x1200 66.0* 1280x1024 76.0 1024x768 76.0 800x600 73.0 640x480 73.0 640x400 0.0 320x400 0.0 1680x1050_60.00 (0x4f) 146.2MHz h: width 1680 start 1784 end 1960 total 2240 skew 0 clock 65.3KHz v: height 1050 start 1053 end 1059 total 1089 clock 60.0Hz However, colors seem a bit faded and blurry with nouveau drivers. Mouse cursor is invisible if it's placed inside Firefox window, and only one monitor is working. I like open source and if it's possible I'd prefer to use nouveau drivers but a few things should be fixed. I'm curious why nvidia-current drivers from the repository don't work now. I read it has something to do with the new X11 server in Ubuntu 12.04, is it true? How can I get it back to work?

    Read the article

  • New computer hangs on shutdown/reboot, how to troubleshoot?

    - by Torben Gundtofte-Bruun
    My system is working perfectly but it freezes during shutdown/reboot/suspend/hibernate: All windows and the menu bar disappear but the desktop wallpaper remains. It doesn't even show the shutdown screen (the one with the animated dots) where I could hit ESC and watch the shutdown console text. The system is brand-new and fully updated using Update Manager. How can I determine what is causing the freeze? Is there a log I can investigate? How can I fix this? I see no obvious cause of the freeze. The only USB attachment is a mouse/keyboard; I don't have any external storage attached; and I don't have any programs running (the machine freezes even when doing shutdown right from the login screen). What I've tried so far: Based on other questions (this, this, and this) that suggest some ACPI settings, I've tried sudo shutdown -h now to see whether the shutdown console text display offers any hints, but the system doesn't even get that far - it still freezes while the screen shown the desktop background image, without any toolbars. Only sudo shutdown --force works, but that's not a solution. Editing the grub menu to add acpi=off to the kernel didn't help. I guess there's not much point in trying the other (lesser) ACPI suggestions? Adding noapic to the grub entry had no discernible effect. Adding nolapic instead did something (I had removed the quiet option) - the system managed to continue further with the shutdown, right until the line Checking for running unattended-upgrades: which were the last characters on the screen. I've also checked the system BIOS, especially regarding power options, but didn't see anything out of the ordinary. Switching the BIOS standby setting from S3 to S1 didn't help. The standby setting can't be disabled, and there are no other ACPI-related settings AFAIK. BIOS reset didn't help. Not surprised; hadn't changed anything. I tried going to a virtual console (CtrlAltF1) as suggested by djeikyb and from there did a shutdown -h now and it froze there too, after this console output. I didn't try killing processes one at a time because I'm still too newbie to figure out how to do that. Booting with kernel 2.6.35.22 rather than 2.6.35.25 didn't help. Disabling the Nvidia drivers didn't help. Booting from Live CD (USB stick in fact) didn't help; it freezes the same way. Booting from Live CD, with acpi=off noapic nolapic didn't help either. Neither did just nolapic. So evidently this is not some custom setting in my install, but some sort of basic issue. MemTest competed in 1 hour without errors.

    Read the article

  • Lenovo W520 back usb port not working

    - by jaudette
    The usb port in the back of my laptop (on the right side when viewed from using perspective) is not working. Does anybody know if we can get this port working, and what the port number is. Here is my lsusb, if it can help. % lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 003 Device 002: ID 046d:c01e Logitech, Inc. MX518 Optical Mouse Bus 003 Device 003: ID 046d:c318 Logitech, Inc. Illuminated Keyboard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0765:5001 X-Rite, Inc. Huey PRO Colorimeter Bus 001 Device 004: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 005: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 006: ID 04f2:b217 Chicony Electronics Co., Ltd Lenovo Integrated Camera (0.3MP) Bus 002 Device 003: ID 17ef:1003 Lenovo Integrated Smart Card Reader I am running 12.10, upgraded from 12.04 but it did not work either in 12.04. The two usb ports on the left work just fine. EDIT: I just updated my bios from 1.32 to 1.39, no change in behaviour. The port does not even power up my devices. EDIT 2: Booted up windows, and the port is working. I went into the device manager and looked at the USB settings. I found my USB drive on Port 2, Hub 3, i just don't know how that relates to the Bus and Device numbers of linux. In windows, Smart card reader was on USB hub located at port 1 hub 2, fingerprint and bluetooth were on USB hub located at port 1 hub 1 EDIT 3: Went and looked at this SO post. Tried to look at my kern.log file with tail -f /var/log/kern.log. Got some activity when plugging/removing devices in other ports, but nothing happens when connecting a device into that port. It really looks disabled. Looked at my usb1-4 sys/bus/usb/devices/usb1/power/control and they are all set on auto. As expected, usb4 have version 3.00, the others (usb1-usb3) are 2.00.

    Read the article

  • What are these errors when I try to "make" the driver of my wireless network?

    - by Tom Brito
    I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme file say to use the "make" command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

    Read the article

  • No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

    - by jrosell
    Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

    Read the article

  • Get AutoHotkey Script To Run As Admin At Startup

    - by deadlydog
    A few weeks back I posted some problems with running AutoHotkey (AHK) in Windows 8, and that the solution was to run your AHK script as admin.  I also showed how to have the script start automatically when you logged into Windows.  What I didn’t realize at the time though was that the method only worked because I had disabled UAC in the registry (which prevents most Metro apps from working in Windows 8, and likely isn’t acceptable for most people). So here is a Windows 8, UAC-friendly method to accomplish the same task (also works in previous versions of Windows).  The trick is to use the Task Scheduler: 1. Open the Task Scheduler (also known as “Schedule tasks” in Windows 8 Settings).   2. Create a new Basic Task. 3. Give it a name and description (something like “launch AutoHotkey script at login”), and then specify to have it run “When I log on”.  Then specify that you want it to “Start a program”, and then point it towards your AutoHotkey script.  Before you finish the wizard, check off “Open the Properties dialog for this task when I click Finish”.   4. When that Properties dialog opens up, go to the Conditions tab and make sure none of the checkboxes under the Power category are checked off; this will ensure the script still launches if you are on a laptop and not plugged into AC power.   5. Now here is the important part; To have your script “Run as admin”, on the General tab check off “Run with highest privileges”. Now your AHK script should start automatically as soon as you log into Windows; even when UAC is enabled   6. If your AHK script uses an #Include statement to include other files, you may get an error similar to this one when your task runs: “#Include file … cannot be opened. The program will exit.” The solution to this is to tell your AHK script to start in the same directory as the file that you want to include.  So you will need to edit your scheduled task’s Action to specify the Start In directory. Happy coding!

    Read the article

  • WebCenter Content Web Search Performance: Do you really need that folder path info?

    - by Nicolas Montoya
    End-users want content at their fingertips at the speed of thought if possible. When running search operations in the WebCenter Conter Web Interface every second or fraction of a second improvement does matter. When doing some trace analysis on the systemdatabase tracing on a customer environment, we came across some SQL queries that were unnecessarily being triggered! These were related to determining the folder path for every entry part of the search result set. However, this folder path was not even being used as part of the displayed information in the user interface.Why was the folder path information being collected when it was not even displayed in the UI? We found that the configuration parameter 'FolderPathInSearchResults' was set to 'true' under Administration > Admin Server > General Configuration > Additional Configuration Variables as shown below:When executing a quicksearch by keyword we were getting 100 out of 2280 entries in the first page of the result set.When thera 'FolderPathInSearchResults' configuration parameter is set to 'true', the following queries appear in the systemdatabase tracing:100 executions for a query on the FolderFiles table for each of the documents displayed in the first page:>systemdatabase/6       12.13 11:17:48.188      IdcServer-199   1.45 ms. SELECT * FROM FolderFiles WHERE dDocName='SLC02VGVUSORAC140641' AND fLinkRank=0[Executed. Returned row(s): true]382 executions for a query of the folders tables - most of the documents that match the keyword criteria are at a folder depth level of three or four:>systemdatabase/6       12.13 11:17:48.114      IdcServer-199   2.57 ms. SELECT FolderFolders.*,FolderMetaDefaults.* FROM FolderFolders,FolderMetaDefaults WHERE FolderFolders.fFolderGUID=FolderMetaDefaults.fFolderGUID(+) AND((FolderFolders.fFolderGUID = '1EB8E527E19B09ED3FE82EE310AEA13A' ) )[Executed.Returned row(s): true]By setting this 'FolderPathInSearchResults' configuration parameter to 'false', the above queries were no longer reported in the Server Output System Audit Information.Now, let's consider a practical scenario:Search result set page = 100Average folder depth der document in the search result set: 5The number of folder path related queries will be: 100 + 5*500 = 600If each query takes slightly over 3 ms. You would have 2000 ms (2 seconds) spent in server time to get this information.The overall performance impact goes beyond seerver time execution, as this information needs to travel from the server to the browser. If the documents are further nested into the folder hierarchy, additional hundreds of queries may be executed. If folder path is not being displayed in the end-user interface profile, your system may be better of with the 'FolderPathInSearchResults' configuration parameter disabled.

    Read the article

  • Dual booting windows 8/ubuntu 12.04.2, Grub doesn't appear and machine never boot in ubuntu

    - by black sensei
    i got a new ACER predator AG3620-UR308 which came with windows 8, so i wanted to run ubuntu 12.04.2 on it as a dual booting. To be honest, i've been doing dual booting for a while now so, i did the right thing. the box came with 2TB HDD. so i made 4 partitions with a raw partition just after the windows installation partition I always do manual installation so even if ubuntu didn't detect windows 8, it was ok for me. So i created swap area and finished the installation etc....Grub was install on the only drive there which is sda. After reboot, grub doesn't even come up.So it always boot in windows 8. I did repeat the installation process twice and yield same result. which is weird because this method always works for me so far.Even the laptop am using to write this post is a dual booting windows 7/ mint nadia installed the same way. Is there anything new in windows 8 that i didn't make provision for? Before starting the installation, all i read about was that , windows 8 should be installed first and ubuntu after. I went ahead and disable secure boot from the BIOS and enabled CSM (don't even know what it means) according to Acer custhelp site . I boot from USB and did fdisk -l bellow is the result: ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x8c361cb5 Device Boot Start End Blocks Id System /dev/sda1 1 3907029167 1953514583+ ee GPT Partition 1 does not start on physical sector boundary. Disk /dev/sdb: 8178 MB, 8178892800 bytes 255 heads, 63 sectors/track, 994 cylinders, total 15974400 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0006a87e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 15972351 7985152 b W95 FAT32 ubuntu@ubuntu:~$ Can anybody shed some light? thank you in advance EDIT Hey, i just did another trial with 13.04 this time and still no luck. bios: secure-boot: disabled enable CSM : always 1-delete previous ubuntu partition and swap area partition.now having free space 2- used usb installer to prepare usb with ubuntu-13.04-desktop-amd64.iso 3- rebooted : liveusb didnt detect windows 8, used something else 4-created partition ext4 for / 5-created partition for swap-area 6- default grub path is /dev/sda and clicked install Acer always boots into windows.

    Read the article

  • ATI Radeon HD7000 Series (Laptop) - Switch Mode Between ATI & Intel Integrated GPU. Stuck on Boot Screen On Intel GPU Selection Mode

    - by Monkey Drone
    Laptop Specs: HP Pavilion G6-2020SE GPUs 1) ATI HD7000 Series 2) Intel Integrated OS Installed: x) Ubuntu 12.04 (64 bit) i) ATI Graphics Card Drivers Installed From AMD website. Note: Graphics Card Drivers are Working Fine in 3D Mode. It runs a little Hot as it should since its a GPU. Observation) AMD Catalyst Control Centre Lets me Choose If I want to run the system in HIGH-END (ATI GPU) OR Intel Integrated (Better battery life) While I am on High End GPU Choice, Ubuntu works fine. Problem) But when I switch to Intel Mode in the AMD CCC and reboot the Machine. Ubuntu goes into 'Low Graphics Mode'. The problem is not that it goes into low graphics mode, it is completely expected since I am no longer using the ATI GPU but the integrated Intel GPU. Problem starts with the 'Selection' of the options. During that screen, I have no mouse on the screen (even tried plugging in an external USB mouse) & No Keyboard functionality. Thus I am left completely disabled to choose any option and load into Ubuntu. The Only thing I can do is switch to a terminal and enable ATI GPU through command-line and Ubuntu works Fine again. Is it a bug that there is no mouse/keyboard available to me during the startup of Ubuntu when its launched in Low-Graphics Mode? Any suggestions on how to pass through that? My palms are sweating as I write this down because the ATI GPU is really heating up my laptop. I dont want to boot into Windows or keep it around any longer than necessary. Please advise with help and directions. Sincerely, MonkeyD Edit1: The Answer by Celso has helped me switch to Intel, thus giving me sufficient battery power. Kudos to Celso. Now I can at least use my laptop for the time being without having it burn hair off my skin. I am still looking for answer to my original question of, 'why is lightdm not working properly when I switch to Intel GPU using ATI HD7000 series official drivers provided by AMD'.

    Read the article

  • Can't access some websites using Ubuntu 13.10

    - by Adame Doe
    Something's wrong with Ubuntu. Since I've upgraded to 13.10, I can't access some websites for no apparent reason. I've tried everything imaginable to solve this problem : Made sure that MTUs are the same, Disabled IPv6 in both the network manager and used browsers, Deactivated my network keys, DMZed my computer, Used other DNS like Google and OpenDNS, Checked that no firewall was running my computer ... And it's the same result. I even tried to reinstall Ubuntu a couple of times, but no luck. The most annoying thing about it is I can't access wordpress.org! So, there's no way it could be an ISP restriction of some kind. When I use a VPN, I can access pretty much anything. I'm really frustrated because I have to use wordpress.org very often. Any clue? ifconfig adame@adame-ws:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:3d:b0:7c inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::226:18ff:fe3d:b07c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8024 errors:0 dropped:0 overruns:0 frame:0 TX packets:7966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:684480 (684.4 KB) TX bytes:616608 (616.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:8222 errors:0 dropped:0 overruns:0 frame:0 TX packets:8222 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:568269 (568.2 KB) TX bytes:568269 (568.2 KB) wlan0 Link encap:Ethernet HWaddr 00:19:70:40:85:eb inet addr:192.168.2.3 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::219:70ff:fe40:85eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1464 Metric:1 RX packets:123705 errors:0 dropped:0 overruns:0 frame:0 TX packets:98141 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:94963545 (94.9 MB) TX bytes:10387470 (10.3 MB) /etc/hosts 127.0.0.1 localhost 127.0.1.1 adame-ws ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters tracepath wordpress.org 1: adame-ws.local 0.092ms pmtu 1500 1: 192.168.2.1 1.300ms asymm 2 1: 192.168.2.1 1.060ms asymm 2 2: no reply 3: no reply 4: no reply 5: no reply 6: no reply 7: no reply 8: no reply ... keep on going like that ping wordpress.org adame@adame-ws:~$ ping wordpress.org PING wordpress.org (66.155.40.250) 56(84) bytes of data. --- wordpress.org ping statistics --- 10 packets transmitted, 0 received, 100% packet loss, time 9071ms

    Read the article

  • Why do some user agents have spam urls in them (and why are they always Opera/Presto User-Agents)?

    - by Erx_VB.NExT.Coder
    If you go to (say) the last 100 entries (visits) to the botsvsbrowsers.com website (exact link, feel free to take a look: http://www.botsvsbrowsers.com/recent/listings/index.html ), you'd notice that almost every User Agent that has the keywords "Opera" and "Presto" inside them, will almost certainly have a web link (URL/Web Address) inside it, and it won't just be a normal web address, but a HTML anchor tag/link to that address. Why is this so, I could not even find a single discussion about it on the internet, nowhere, I tried varying my search terms many times. If the user agent contains the words "Opera" and "Presto" it doesnt mean it will have this weblink, but it means there is about an 80% change that it will. A typical anchor tag/link inside a user agent will look like this: Mozilla/4.0 <a href="http://osis-uk.co.uk/disabled-equipment">disability equipment</a> (Windows NT 5.1; U; en) Presto/2.10.229 Version/11.60 If you check it out at the website, http://www.botsvsbrowsers.com/recent/listings/index.html you will notice that the back and forward arrows are in there unescaped format. This isn't just true for botsvsbrowsers, but several other user agent listing sites. I'm really confused and feel line I'm in a room full of 10,000 people and am the only one seeing this ghost :). If I'm doing statistical analysis, should I include or exclude this type of user agent from my listing (ie: are these just normal users who've set their user agents to attempt to drive some traffic to their sites as they browser the web), or is there something else going on? The fact that it is so consistent in terms of its format leads me to believe that it is an automated process (the setting or alteration of the user agent) so I cannot decide or understand the process by which this change is made (I know how to change a user agent), but unsure which program or facility is doing this, especially since it is exclusive to Opera (Presto) user agents that are beyond I think an 8 or 9 point something browser version. I've run some statistical tests, parsing entries from all over the place, writing custom programs, to get a better understanding of this. Keep in mind that I see normal URL's in user agents infrequently, they are just text such as +http://www.someSite.com appended to a user agent normally, especially if its a crawler or bot it provided its service URL, this is normal and isnt done with an embedded link (A HREF=) etc, so I'm not talking about "those".

    Read the article

  • Operation times out trying to SSH outside LAN i.e. from internet to LAN no connection is established

    - by Pelle L
    I run Ubuntu 12.04 and have no success connecting with SSH from "Internet". The router is a TL-MR3420 which is set up to forward requests to one of the NIC's on ubuntu machine (which has in total 3 NICs). I can SSH from a client on the "local" network/LAN. The forward mechanism in the router seems to work. If I stop SSH service on the Ubuntu machine and instead start one on the windows machine - it works like a charm. I do not use the Std port 22 but that shouldn't be an issue as far as I understand - sine it works on the same port on the win machine. Since my public IS isn't static I use a dynDNS service but as said earlier the same setup works from the win machine. The router is located on 192.168.0.1 The Ubuntu NICs has the following IP: eth2 192.168.0.100 , eth1 192.168.0.101 , eth0 192.168.0.102 and I have forwarded the "outside" request to 192.168.0.100 In regards for firewall settings on the Ubuntu machine I have disabled the ufw and the command ufw status give status: inactive. I don't now it this is relevant information but teh command iptables --list give: Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I have tried to catch traffic with help of wireshark (a tool I'm not too used to use) and it seems as a few (3?) "requests" actually reaches the NIC but ... nothing happens. The syslog does not show any entries during these attempts. Perhaps it could be some routing issues but I have reached my level of competence and are stuck ... all help and support to get this sorted out is much appreciated. I'm new to Linux so please do not assume I have a configuration that is correct - but as I wrote earlier - if the client that initiate SSH is on the LAN it all works. PS:I have also tried to get VPN (PPP) working from Internet with no success - once again VPN works on the windows machine ... so my best guess is that this is related to how the ubuntu machine handles (IP) traffic and not the TL-MR3420 router or other network issues.

    Read the article

  • Can my machine run Ubuntu( kubuntu | xubuntu | mint ) 12.04 WELL?

    - by Steve
    I have a 9 year old computer packing the hardware listed below. My question is, can I run 12.04 ( Ubuntu, Kubuntu, MINT or Xubuntu ) WELL? I was running Ubuntu 10.10 and I upgraded to 12.04 by going through each release via the update manager: 11.04 - 11.10 -12.04 During the installation process for 12.04 I saw an error message that there was an error installing and setting up part of the kernel. Later, when I tried installing a package in synaptic, I got another error message mentioning the kernel. When I rebooted, I got told somehting about my video and graphics was not configured properly and that I would have to do it manually ( like I know ). It gave me the option to enter the system in low graphics mode, but it just hanged. I had an old livecd of Xubuntu 10.10 around so I used that to get into my computer and copy data over to an external hard drive. I think tried to install Xubuntu 10.10 from the livecd, with the option "download updates" checked. The install process moved along a bit, then halted for about 5 hours. I rebooted my machine and tried the Xubuntu 10.10 installer WITHOUT the option to "download updates". The install completed in about 15 minutes. So, all of that is making me wonder if there is someting about 12.04 that does not like my hardware. I'm willing to try again, but only if I know I will not have to spend hours just to get to an error message and a hosed up system like I did last night. I also think I have a lot more RAM than is being reported in the output below. I had extra ram installed last year. I'm not good with the command line readouts, but there seems like there should be a lot more. I wasn't thrilled with Unity. I am willing to try Kubuntu 12.04. Will I run into the same problems? What is the highest version of a *ubuntu can I upgrade to? Thanks CPU Model: Intel(R) Pentium(R) 4 CPU 2.53GHz Frequency: 2533.223 MHz L2 Cache: 512 KB Bogomips: 5066.44 Numbering: family(15) model(2) stepping(7) Flags: fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe up pebs bts cid RAM ~$ free -mt total used free shared buffers cached Mem: 1506 891 615 0 91 521 -/+ buffers/cache: 278 1227 Swap: 1609 0 1609 Total: 3116 891 2225 Video Card 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. V9180 Magic Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16 Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Memory at f0000000 (32-bit, prefetchable) [size=64M] Expansion ROM at fe9e0000 [disabled] [size=128K] Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb Motherboard Intel 845PE ATX 533FSB DDR333 USB2

    Read the article

  • how did Google Analytics kill my site?

    - by user1813359
    Yesterday I created a google analytics profile for one of my sites and included the JS block in the layout template. What happened next was very strange. Within about 2 minutes, the site had become unreachable. I had been checking the AWStats page for the site when I thought to set up GA. After that had been done, I clicked on the link for 404 stats, which opens in a new tab. It churned for a long while and then showed a nearly blank page, similar to that when Firefox chokes on a badly-formatted XML page, except there was no error msg. But i was logged into the server and could see that that page has a 401 Transitional DTD. Strange! I tried viewing source but it just churned endlessly. I then tried "inspect element" and was able to see an error msg having to do with some internal Firefox lib. Unfortunately, i neglected to copy that. :-( All further attempts to load anything on the site would time out. Firebug's Net panel showed no request being made. Chrome would time out. So, I deleted the GA profile, removed the JS block, and cleared the server cache. No joy. I then removed all google cookies and disabled JS. Still nothing. No luck in any other browser. And now my client couldn't access the site. Terrific. I was able use wget while logged into another server. The retrieved page was fine, and did not contain the GA JS block. However, the two servers are on the same network. (Perhaps a clue.) The server itself was fine. Ping, traceroute looked great. I could SSH in. I tailed the access log and tried a browser request. Nothing. But i forgot to quit and a minute or so later I saw a request from someone else being logged. Later, I could see that requests had been served all day to some people. Now, 24 hours later, the site works once again, but is still unreachable by the client (who is in another city). So, does anyone have some insight into what's going on? Does this have something to do with google's CDN? I don't know very much about how GA works but what I'm seeing reminds me of DNS propagation issues. And why the initial XML error? And why the heck was the site just plain unreachable? What did google do to my site?! Sorry for the length but I wanted to cover everything.

    Read the article

  • 12.04 Booting into Terminal

    - by user170796
    To preface this, I would like to say that I am completely new to Ubuntu and have essentially zero programming experience/experience working with command line and terminal. I installed Ubuntu because I would like to get into programming. If you could provide me with the simplest instructions possible, I would be grateful. I have a Lenovo Ideapad Y500 (Intel i7, NVidia GT 750m, 1TB HDD, 16GB SSD cache, 8GB RAM) with Windows 8 on it. Using a Live CD, I installed Ubuntu 12.04 onto a 75 GB partition. During the installation, I kept all default settings except for one thing; I decided to encrypt my home folder, and so checked the corresponding box. The installation completed, and I restarted. Once I restarted, I saw the options "Ubuntu, with Linux 3.2.0-23-generic" "Ubuntu, with Linux 3.2.0-23-generic (recovery mode)" "Memory test (memtest86+)" "Memory test (memtest86+, serial console 115200)" "Windows Recovery Environment (loader) (on /dev/sdb3)" "Windows 8 (loader) (on /dev/sdb5)" "System Setup" I chose the first option, and was directed to a screen with the Ubuntu logo and the row of five dots below that change from orange to white. Then, I was brought to a full screen terminal that prompted me to login, which I did. I saw no option to boot into GUI at all, and am lost. I've been searching around and have tried the "startx" command to no avail. Should the command have some sort of context or something? I've also tried selecting the recovery mode option from the boot manager. I've tried the resume option from the following menu, which eventually just shuts down the computer after displaying a lot of scrolling text that's too fast for me to read. I've also tried the failsafex mode from the recovery mode menu, which only brings up a terminal box at the bottom of the window that covers the entire bottom part of the screen. Commands won't work in this window. When I try to access Windows 8, I get a message saying that the EFI file path was not specified or something along those lines. I had to enable Secure Boot in order to access Windows 8 (I had disabled it to be able to boot from the Live CD), which is functioning normally. I am at a complete loss for what to do. Any help will be extremely appreciated. EDIT: Bonus question! If you could figure out a way for me to boot to Windows 8 without having to enable Secure Boot, it would save me a lot of trouble. I can deal with switching every time, but I'd rather not have to.

    Read the article

  • PXE boot linux. PXE-E51: No DHCP or proxyDHCP offers were received

    - by athspk
    I am trying to have an ubuntu box (192.168.10.9) acting as a PXE server, but i have trouble getting DHCP to work. The PXE server is connected to a SOHO router (192.168.10.1) acting as a switch. I have disabled the DHCP server on the router. $ dhcpd --version isc-dhcpd-4.2.4 The contents of /etc/dhcp/dhcpd.conf ddns-update-style none; option domain-name-servers 192.168.10.1; default-lease-time 3600; max-lease-time 7200; authoritative; log-facility local7; allow booting; allow bootp; subnet 192.168.10.0 netmask 255.255.255.0 { range dynamic-bootp 192.168.10.101 192.168.10.200; option routers 192.168.10.1; option broadcast-address 192.168.10.255; next-server 192.168.10.9; filename "/tftpboot/pxelinux.0"; } The contents of /etc/default/isc-dhcp-server INTERFACES="eth0" When the client boots, it tries to get an IP address from the server but fails with the following Error message: PXE-E51: No DHCP or proxyDHCP offers were received. On Server side, i was tailing /var/log/syslog while the client tries to boot: Dec 4 12:57:10 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:11 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:12 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:12 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:17 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:17 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:25 athspk-Dell dhcpd: DHCPDISCOVER from 00:1f:d0:8e:6b:db via eth0 Dec 4 12:57:25 athspk-Dell dhcpd: DHCPOFFER on 192.168.10.101 to 00:1f:d0:8e:6b:db via eth0 Please advise. Thanks in advance

    Read the article

  • Mount CIFS share gives "mount error 127 = Key has expired"

    - by djk
    Hi, I'm currently replicating the setup of a CentOS box an am running into a strange error while trying to mount a samba share that resides on a NAS. The error I'm getting is: mount error 127 = Key has expired Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) The settings are identical to the old machine, the password is definitely correct as well. I have googled the issue of course, and looked at every single page that references this issue (not that many) and have still not found an answer. The older CentOS box is using version 3.0.28-0.el4.9 of Samba and the one I'm trying to setup now is 3.0.33-3.7.el5_3.1. I don't know if this has anything to do with it but it's certainly one of the only differences between the 2 setups. When I try the mount command this appears in the syslog: Sep 8 10:51:54 helvetica2 kernel: Status code returned 0xc0000072 NT_STATUS_ACCOUNT_DISABLED Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: Send error in SessSetup = -127 Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: cifs_mount failed w/return code = -127 The account is very much not disabled as it works on the old box using the same credentials. Has anyone else seen this problem? Thanks!

    Read the article

  • LDOMs in Solaris 11 don't work

    - by Giovanni
    I just got a new Sun Fire T2000, installed Solaris 11 and was going to configure LDOMs. However "ldmd" can't be started and in turn ldm doesn't work. root@solaris11:~# ldm Failed to connect to logical domain manager: Connection refused root@solaris11:~# svcadm enable svc:/ldoms/ldmd:default root@solaris11:~# tail /var/svc/log/ldoms-ldmd\:default.log [ May 28 12:56:22 Enabled. ] [ May 28 12:56:22 Executing start method ("/opt/SUNWldm/bin/ldmd_start"). ] Disabling service because this domain is not a control domain [ May 28 12:56:22 Method "start" exited with status 0. ] [ May 28 12:56:22 Stopping because service disabled. ] [ May 28 12:56:22 Executing stop method (:kill). ] Why is this not a control domain? There is no other domain on the box (as far as I can tell). I have upgraded the firmware to the latest 6.7.12, booted with reset_nvram, nothing helped ... sc> showhost Sun-Fire-T2000 System Firmware 6.7.12 2011/07/06 20:03 Host flash versions: OBP 4.30.4.d 2011/07/06 14:29 Hypervisor 1.7.3.c 2010/07/09 15:14 POST 4.30.4.b 2010/07/09 14:24 What else should I do? Thanks!

    Read the article

  • What does Active, Targetset, and Active targetset mean in the Output of dfsutil /pkiinfo?

    - by Kyle Brandt
    I could use some guidance in interpreting the output of dfsutil /pktinfo. Using the following example: PS C:\Users\kbrandt dfsutil.exe /pktinfo ... Entry: \long.biz.foo\Images ShortEntry: \long.biz.foo\Images Expires in 4 seconds UseCount: 1 Type:0x81 ( REFERRAL_SVC DFS ) 0:[\OR-UTIL01\Images] ( TARGETSET ) 1:[\NY-FS01\Images] AccessStatus: 0xc00000be ( TARGETSET ) 2:[\NY-UTIL01\Images] AccessStatus: 0 ( ACTIVE ) Entry: \NY-UTIL01\Images ShortEntry: \NY-UTIL01\Images Expires in 65 seconds UseCount: 0 Type:0x81 ( REFERRAL_SVC DFS ) 0:[\or-util01\Images] ( TARGETSET ) 1:[\NY-FS01\Images] AccessStatus: 0xc00000be ( TARGETSET ) 2:[\NY-UTIL01\Images] AccessStatus: 0 ( ACTIVE ) Entry: \or-util01\Images ShortEntry: \or-util01\Images Expires in 0 seconds UseCount: 0 Type:0x81 ( REFERRAL_SVC DFS ) 0:[\OR-UTIL01\Images] AccessStatus: 0 ( ACTIVE TARGETSET ) 1:[\NY-UTIL01\Images] ( TARGETSET ) 2:[\NY-FS01\Images] Entry: \FOO\Images ShortEntry: \FOO\Images Expires in 108 seconds UseCount: 0 Type:0x81 ( REFERRAL_SVC DFS ) 0:[\OR-UTIL01\Images] AccessStatus: 0 ( ACTIVE TARGETSET ) 1:[\NY-UTIL01\Images] ( TARGETSET ) 2:[\NY-FS01\Images] What do the three states TARGETSET, ACTIVE TARGETSET, and ACTIVE mean exactly? In particular, why might OR-UTIL01 be ACTIVE for \long.biz.foo\Images but the shortname version FOO\Images have NY-UTIL01 as ACTIVE TARGETSET? I'd like to have a better understanding of this to know if it is normal or not. Once I understand it, I might be looking at and issue with IPv6 being disabled (http://support.microsoft.com/kb/2003961) if this isn't normal.

    Read the article

  • QNTC and Windows Server 2008 R2

    - by Ben
    I am having a really hard time getting an iSeries (AS/400) machine talking to my new Windows Server 2008 R2 box using the QNTC file system on the iSeries. I had similar problems getting it to initially talk to a Windows Server 2003 machine, but enabling the local Guest account on the 2003 box solved that one. No such luck with the new 2008 box. When I do a WRKLNK /QNTC/SVR01 on the iSeries (which should show share listings, and does on any 2003 boxes) all I get is (Cannot find object to match specified name.). I know the iSeries likes the same username and password on the remote server, but unfortunately for us this is not the case. Anyhow, it does currently work with different username/password combinations on a 2003 box. To try and get the wretched things talking, I have made the 2008 server pretty open but the iSeries will not see shares on it. I have enabled the local Guest account, turned Windows firewall off, set the share permissions so Everyone has full control but to no avail. I read something on the internet about the iSeries only being able to handle NTLM authentication (and I understand by default that Server 2008 R2 only uses NTLMv2 and has NTLM disabled), so I made a special group policy for the server and tweaked all Group Policy settings under Computer Configuration\Policies\Windows Settings\Security Settings\Local Policies\Security Options but the iSeries STILL won't see it. We have a team of programmers who do all the system administration of the iSeries, but they are stumped for ideas on their side, and I'm stumped for ideas on my side. This is driving me crazy now, and if anybody has managed to get an iSeries to talk to Windows Server 2008 R2 using QNTC I would be very appreciative of any suggestions, be it on the Windows side, iSeries settings or even IBM PTF's that might patch anything. The iSeries is running V5R4 and I have *SECOFR privileges on it, if it helps. One final (most important!) note - The programmers think it's my system being tricky, and I think it's theirs - please prove me right :)

    Read the article

  • Networking stopped working on Ubuntu

    - by 1337Rooster
    I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the wireless/networking icon it says "Networking Disabled". I reinstalled Ubuntu and the problem went away. After a few reboots the problem returned. I have tried restarting to see if it would come back as well as a few other things listed below. Any other suggestions would be appreciated. Tried to restart networking via /etc/init.d/networking: amato@ubuntu:~$ sudo /etc/init.d/networking restart * Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0. [ OK ] Tried to stop and start it: amato@ubuntu:~$ sudo /etc/init.d/networking stop * Deconfiguring network interfaces... [ OK ] amato@ubuntu:~$ amato@ubuntu:~$ sudo /etc/init.d/networking start Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service networking start Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the start(8) utility, e.g. start networking networking stop/waiting Tried start networking: amato@ubuntu:~$ start networking start: Rejected send message, 1 matched rules; type="method_call", sender=":1.58" (uid=1000 pid=2241 comm="start) interface="com.ubuntu.Upstart0_6.Job" member="Start" error name="(unset)" requested_reply=0 destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")) amato@ubuntu:~$ sudo start networking networking stop/waiting Tried service networking restart: amato@ubuntu:~$ service networking restart restart: Rejected send message, 1 matched rules; type="method_call", sender=":1.60" (uid=1000 pid=2248 comm="restart) interface="com.ubuntu.Upstart0_6.Job" member="Restart" error name="(unset)" requested_reply=0 destination="com.ubuntu.Upstart" (uid=0 pid=1 comm="/sbin/init")) amato@ubuntu:~$ sudo service networking restart restart: Unknown instance: Here are the contents of my /etc/network/interfaces. auto lo iface lo inet loopback I even tried to modify it to this (based on something I read, online, not sure if I was doing the right thing here). Tried everything again and no luck: auto lo eth0 iface lo inet loopback iface eth0 inet dhcp

    Read the article

  • Teamcity build agent gives 504 gateway timeout

    - by Anthony
    I have a new teamcity build agent machine, which when started up tries to connect to the build server and fails. It never shows up in the connected, disconnected or unauthorised agents tabs of the build server web interface. The logs on the build agent show that it fails to connect with a 504 gateway timeout. This is from teamcity-agent.log [2012-09-04 15:34:59,776] INFO - buildServer.AGENT.registration - Registering on server http://10.0.10.16, AgentDetails{Name='my-local', AgentId=null, BuildId=null, AgentOwnAddress='10.0.1.14', AlternativeAddresses=[10.0.10.32], Port=8080, Version='21424', PluginsVersion='21424-md5-somechecksum', AvailableRunners=[ABunchOfPlugins], AvailableVcs=[SomeRunners], AuthorizationToken='sometoken'} [2012-09-04 15:35:53,606] WARN - buildServer.AGENT.registration - Call http://10.0.10.16/RPC2 buildServer.registerAgent3: org.apache.xmlrpc.XmlRpcClientException: Server returned incorrect status code: 504 Gateway Time-out [2012-09-04 15:35:53,606] WARN - buildServer.AGENT.registration - Connection to TeamCity server is probably lost. Will be trying to restore it. Take a look at logs/teamcity-agent.log for details (unless you're using custom logging). (I have edited some identifying data out of this log excerpt) But I can reach the build server. In fact, tracert shows that it is very nearby. Tracing route to TEAMCITYSERVER [10.0.10.16] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 10.0.2.1 2 <1 ms <1 ms <1 ms TEAMCITYSERVER [10.0.10.16] Trace complete. I can see a teamcity login page if I hit http://10.0.10.16 in the browser. The teamcity service is logging in as the same (local administrator) account as I used to log in and test the network. The build agent is a windows 2008 server VM hosted on Ubuntu 12.04 under Oracle VirtualBox. I have disabled firewalls on both the Windows and Ubuntu machines. Other VMS with similar configuration can connect fine and do not report this error. What can possibly be preventing this connection?

    Read the article

  • SD Card reader not working on Sony Vaio

    - by TessellatingHeckler
    This laptop (Sony Vaio VGN-Z31MN/B PCG-6z2m) has been installed with Windows 7 64 bit, all the drivers from Sony's VAIO site are installed, and everything in Device Manager both (a) has a driver and (b) shows as working, no exclamation marks or warnings. "Hide empty drives" in Folder options is disabled so the card reader appears, but will not read the card ("please insert a disk in drive O:"). Previously, when the laptop had Windows XP on it, it could read the same card. Also, Windows update suggested driver ("SD Card Reader") doesn't work, Ricoh own drivers install properly but do the same behaviour. Other 3rd party driver suggestions from forums (Acer and Texas-Instruments FlashMedia) do not seem to install properly. I would post the PCI id if I had it, but it was just showing up as rimsptsk\diskricohmemorystickstorage (while it had the Ricoh Driver installed). Edit: If there are any lower level diagnostic utlities which might shed more light on it I'd welcome hearing of them. Anything which might show get it to put troubleshooting logs in the event log or identify chipsets or whatever... Update: Device details are: SD\VID_03&OID_5344&PID_SD04G&REV_8.0\5&4617BC3&0&0 : SD Memory Card PCI\VEN_8086&DEV_2934&SUBSYS_9025104D&REV_03\3&21436425&0&E8: Intel(R) ICH9 Family USB Universal Host Controller - 2934 PCI\VEN_1180&DEV_0476&SUBSYS_9025104D&REV_BA\4&1BD7BFCD&0&20F0: Ricoh R/RL/5C476(II) or Compatible CardBus Controller RIMSPTSK\DISK&VEN_RICOH&PROD_MEMORYSTICKSTORAGE&REV_1.00\MS0001: SD Storage Card PCI\VEN_1180&DEV_0592&SUBSYS_9025104D&REV_11\4&1BD7BFCD&0&24F0: Ricoh Memory Stick Host Controller WPDBUSENUMROOT\UMB\2&37C186B&1&STORAGE#VOLUME#_??_RIMSPTSK#DISK&VEN_RICOH&PROD_MEMORYSTICKSTORAGE&REV_1.00#MS0001#: O:\ STORAGE\VOLUME\{C82A81B8-5A4F-11E0-AACC-806E6F6E6963}#0000000000100000: Generic volume PCI\VEN_1180&DEV_0822&SUBSYS_9025104D&REV_21\4&1BD7BFCD&0&22F0: SDA Standard Compliant SD Host Controller ROOT\LEGACY_FVEVOL\0000 : Bitlocker Drive Encryption Filter Driver PCI\VEN_1180&DEV_0832&SUBSYS_9025104D&REV_04\4&1BD7BFCD&0&21F0: Ricoh 1394 OHCI Compliant Host Controller Now going to search for drivers for that.

    Read the article

  • Mount CIFS share gives "mount error 127 = Key has expired"

    - by djk
    I'm currently replicating the setup of a CentOS box an am running into a strange error while trying to mount a samba share that resides on a NAS. The error I'm getting is: mount error 127 = Key has expired Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) The settings are identical to the old machine, the password is definitely correct as well. I have googled the issue of course, and looked at every single page that references this issue (not that many) and have still not found an answer. The older CentOS box is using version 3.0.28-0.el4.9 of Samba and the one I'm trying to setup now is 3.0.33-3.7.el5_3.1. I don't know if this has anything to do with it but it's certainly one of the only differences between the 2 setups. When I try the mount command this appears in the syslog: Sep 8 10:51:54 helvetica2 kernel: Status code returned 0xc0000072 NT_STATUS_ACCOUNT_DISABLED Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: Send error in SessSetup = -127 Sep 8 10:51:54 helvetica2 kernel: CIFS VFS: cifs_mount failed w/return code = -127 The account is very much not disabled as it works on the old box using the same credentials. Has anyone else seen this problem? Thanks!

    Read the article

  • Kernel panic while loading Mac OS X on VMWare

    - by Vladimir Gritsenko
    I have Mac OS X 10.6.3 and VMWare 7.1. Trying to run the OS X doesn't work - shortly after booting VMWare announces the machine's death with this pop-up message: The CPU has been disabled by the guest operating system. You will need to power off or reset the virtual machine at this point. The console has a more interesting announcement: The real-time clock was not properly initialized on your system! With a dump of the detected CPU speed (~2.9 GHz), FSB (~94 MHz) and bus ratio (31). Somehow, the code that panics is documented in an accidental .diff file here. Apparently, it commits seppuku if the bus ratio is greater than 30. I underclocked my E6500 to a slower speed, but this apparently didn't make any difference. I can think of two possibilities right now: The CPU info being read is constant, and defines the maximum ability of the CPU. In which case it appears I'm screwed. VMWare presents its own CPU info to the machine, which I can perhaps somehow change. If so, how? If these sound completely off, that's because I'm a real newbie in these matters. Here's hoping you guys can show me the light :-)

    Read the article

< Previous Page | 904 905 906 907 908 909 910 911 912 913 914 915  | Next Page >