Search Results

Search found 26742 results on 1070 pages for 'linux kernel'.

Page 91/1070 | < Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >

• server and user directly connected no pinging...

  - by jtzero

  I have a server(fedora 12) with two nics on it, directly connected to say 192.168.1.0 and 192.168.2.0 the route table looks like this Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 192.168.1.1 255.255.255.0 U 0 0 0 eth0 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 eth0 = 192.168.1.15 eth1 = 192.168.2.1 and a directly connected user (Mythdora) on the 192.168.2.0 network with ip 192.168.2.2 and route table like so Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 0 0 0 eth0 the cable is a crossover and it works all three nics work -- connected my laptop to either end and assign it a valid 192.168.2.0 ip the pings will work. In fact if I disconnect the server side and plug the eth cable into the laptop and have thte box ping the laptop continually remove the eth cable and plug it back into the server both sides ping... unfortunately the box realizing it's connected to a different pc wipes its route table after say ten minutes or so. if I do a trace route from a box on the 1.0 network to the servers 192.168.2.1 interface never get a reply from it. as a note at one point I could ping the server from the 192.168.2.2 box but the server couldnt ping the 192.168.2.2 box.

  Read the article

• KVM Virtual guest Paused on Reboot

  - by David Hamilton

  I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

  Read the article

• How can I use dynamic routing with openvpn tunnels?

  - by pQd

  i'm thinking about using dynamic routing [ OSPF or RIP ] via OpenVPN tunnels. right now i have few offices connected in full mesh, but this is not scalable solution as we add more locations. i would like to avoid situation when plenty of internal traffic is affected if one of two vpn termination points that i plan to use is down. do you have similar configuration working in production? if so - what routing daemon did you use - quagga? something else? did you encounter any problems? thanks!

  Read the article

• RTL8192SU + RTL8191E Linux Issue Installing Driver

  - by s32ialx

  OK I've read tons of fourms of people getting the onboard RTL8191E working and the RTL8192SU working dif is U = USB they are both N and i have both Toshiba L500D-00T pre-installed Win Vistax64-HP and i have obtained the free Win7x64-HP upgrade the onboard wificard sucks and can't hold a stable connection for more then 20minutes in windows but the usb is amazing. Now problem is i tried both Ubuntu and Mandriva with no resolve the issue is the onboard drive detects and actually SHOWS that it's there but no wireless networks detect so it's saying no SSID's are broadcasting which i know is a lie since I'm running a 2wire bell dsl modem with built in wifi and a Linksys wrt54g w/ DD-WRT firmware and both are broadcasting fine. Why don't i use the USB? new in Mandriva Linux Control Center 2010.0 it shows up in Other/Unknown as RTL8191S WLAN Adapter and on the right pane this shows up Identification Vendor: ?Manufacturer Realtek Description: ?RTL8191S WLAN Adapter Media class: ? Connection Bus: ?USB Bus PCI #: ?1 PCI device #: ?5 Vendor ID: ?0x0bda Device ID: ?0x8172 Sub vendor ID: ?0x0000 Sub device ID: ?0x0000 Misc Module: ?rtl819xU In the hardware device manager in mandriva it shows up as unknown but shows that it's realtek and that it's a 8192 chipset. but no option to for a driver install and when i do a make in terminal i get this error and no clue what it means [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# make make: *** /lib/modules/2.6.31.12-desktop-3mnb/build: No such file or directory. Stop. make: *** [all] Error 2 [root@John-PC rtl8192se_linux_2.6.0010.1020.2009_64bit]# any help appreciated. and just encase I'm running currently Mandriva Spring 2010 Free

  Read the article

• Chrooted pygopherd fails to find new directories and files

  - by Carsten R

  I tried to setup a Pygopherd on my server. The default setup works fine, but when I try to change the gophermap to point to a new directory with a new file, I get an error message in my gopher client: --- [1] '/path/to/gopher/newdir' does not exist (no handler found) First I thought this is caused by the chroot in which pygopherd runs as default. But when I disable the chroot, the same error comes up. Did anyone successfully set up pygopherd or knows about a better gopher server?

  Read the article

• High load average due to high system cpu load (%sys)

  - by Nick

  We have server with high traffic website. Recently we moved from 2 x 4 core server (8 cores in /proc/cpuinfo), 32 GB RAM, running CentOS 5.x, to 2 x 4 core server (16 cores in /proc/cpuinfo), 32 GB RAM, running CentOS 6.3 Server running nginx as a proxy, mysql server and sphinx-search. Traffic is high, but mysql and sphinx-search databases are relatively small, and usually everything works blazing fast. Today server experienced load average of 100++. Looking at top and sar, we noticed that (%sys) is very high - 50 to 70%. Disk utilization was less 1%. We tried to reboot, but problem existed after the reboot. At any moment server had at least 3-4 GB free RAM. Only message shown by dmesg was "possible SYN flooding on port 80. Sending cookies.". Here is snippet of sar 11:00:01 CPU %user %nice %system %iowait %steal %idle 11:10:01 all 21.60 0.00 66.38 0.03 0.00 11.99 We know that this is traffic issue, but we do not know how to proceed future and where to check for solution. Is there a way we can find where exactly those "66.38%" are used. Any suggestions would be appreciated.

  Read the article

• Traffic shaping on Linux with HTB: weird results

  - by DADGAD

  I'm trying to have some simple bandwidth throttling set up on a Linux server and I'm running into what seems to be very weird stuff despite a seemingly trivial config. I want to shape traffic coming to a specific client IP (10.41.240.240) to a hard maximum of 75Kbit/s. Here's how I set up the shaping: # tc qdisc add dev eth1 root handle 1: htb default 1 r2q 1 # tc class add dev eth1 parent 1: classid 1:1 htb rate 75Kbit # tc class add dev eth1 parent 1:1 classid 1:10 htb rate 75kbit # tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match ip dst 10.41.240.240 flowid 1:10 To test, I start a file download over HTTP from the said client machine and measure the resulting speed by looking at Kb/s in Firefox. Now, the behaviour is rather puzzling: the DL starts at about 10Kbyte/s and proceeds to pick up speed until it stabilizes at about 75Kbytes/s (Kilobytes, not Kilobits as configured!). Then, If I start several parallel downloads of that very same file, each download stabilizes at about 45Kbytes/s; the combined speed of those downloads thus greatly exceeds the configured maximum. Here's what I get when probing tc for debug info [root@kup-gw-02 /]# tc -s qdisc show dev eth1 qdisc htb 1: r2q 1 default 1 direct_packets_stat 1 Sent 17475717 bytes 1334 pkt (dropped 0, overlimits 2782 requeues 0) rate 0bit 0pps backlog 0b 12p requeues 0 [root@kup-gw-02 /]# tc -s class show dev eth1 class htb 1:1 root rate 75000bit ceil 75000bit burst 1608b cburst 1608b Sent 14369397 bytes 1124 pkt (dropped 0, overlimits 0 requeues 0) rate 577896bit 5pps backlog 0b 0p requeues 0 lended: 1 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 class htb 1:10 parent 1:1 prio 0 **rate 75000bit ceil 75000bit** burst 1608b cburst 1608b Sent 14529077 bytes 1134 pkt (dropped 0, overlimits 0 requeues 0) **rate 589888bit** 5pps backlog 0b 11p requeues 0 lended: 1123 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 What I can't for the life of me understand is this: how come I get a "rate 589888bit 5pps" with a config of "rate 75000bit ceil 75000bit"? Why does the effective rate get so much higher than the configured rate? What am I doing wrong? Why is it behaving the way it is? Please help, I'm stumped. Thanks guys.

  Read the article

• Simulating audio playback on headless linux server

  - by afro

  Hi people, We have a headless linux server (Debian 5) we use for runnin integration tests of our web-page code. Among these tests are ones implemented using Selenium, which practically simulates a user browsing our pages and clicking on things. One of these tests is failing now, because it involves starting a flash-based audio player and checking to see whether the progress bar gets displayed properly. The reason this test fails is that there is no way to play the audio, and no sound card on the machine, which has simple webserver hardware. So, my question would be: Is there a simple way of giving a program the impression that its audio output is being processed, and playback is taking place? I don't have to record the playback, or redirect it or anything like that, just a dummy soundcard, like the dummy X-server we aer using, which actually does not need to display stuff. I have tried using JACK, but it's too complicated, and the documentation does not even answer this very simple question. I also installed alsa on the server; it 'pretends' to run, but when a program tries to play audio, just spews error and debug information having to do with the non-existence of a soundcard. It would be really awesome if one of you has a simple answer to this question. Cheers, Ulas

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• Linux And NTFS Permissions

  - by VGE IT

  Trying to restrict a folder within a directory created in linux filesystem. I have changed the permissions to: root rwx, a special active directory group rwx and all others r. Upon doing so, people that are not in the special AD group can access the directory and modify files. Upon doing so the group changes to "Domain Users" when the user modifies documents within the directory. I have to manualy change the documents default group back to my AD group. I have tried to create another AD group and modify permissons to deny write access. When doing so through windows explorer, the settings seem to take affect until I go back in a look at permissions for the restricted group. No permissions show when I view for the second time. Please assist. Samba share properties [MyShare] comment = "blah blah blah" browseable = yes guest ok = no read only = no path = /xxx/xxxxx/ create mask = 0640 directory mask = 0750 admin users = @"domain\Domain Admins", @"domain\group A", @"domain\group B" valid users = @"domain\Domain Admins", @"domain\group A", @"domain\group B" nt acl support = Yes inherit acls = yes inherit owner = yes inherit permissions = yes

  Read the article

• Bridging Wireless and Wired Interfaces in Linux

  - by The Daemons Advocate

  My network setup is something like: Wireless Router <---> Netbook <---> Ubuntu Desktop ...or, more verbosely (with interfaces): Wireless Router <--(wireless)--> (eth2) Ubuntu Netbook Ubuntu Netbook (eth0) <---(wired)----> (eth0) Ubuntu Desktop In a perfect world, I'd have the desktop wired, but weird circumstances combined with my wanting to understand more about networking in linux make me want to figure out how to bridge these two devices. A bit of googling has given me this example using bridge-utils, and here's how I'm (failing) to setup the bridge (on the netbook): sudo -i ifconfig eth0 0.0.0.0 ifconfig eth2 0.0.0.0 brctl addbr bridget brctl addif bridget eth0 brctl addif bridget eth2 ifconfig bridget up ...then, trying to make sure that the netbook can still get on the internets... route add default gateway 192.168.2.1 dhclient bridget What happens after this is that the dhclient command above (netbook) doesn't get served an IP, and the Desktop, if I run dhclient, it doesn't get served an IP. Some weird considerations might be that I'm running the Network Manager Applet that comes with Ubuntu. While I'm sure I can get a command line wireless configuration setup, it's a bit complex. Can someone give me a shout as to where I'm going wrong? I'd also like to note another related question titled 'Bridging my laptop’s wireless and wired adaptors', however the setup is different to mine.

  Read the article

• dns queries not using nscd for caching

  - by xenoterracide

  I'm trying to use nscd (Nameservices Cache Daemon) to cache dns locally so I can stop using bind to do it. I've gotten it started and ntpd seems to attempt to use it. But everything else for hosts seems to ignore it. e.g if I do dig apache.org 3 times none of them will hit the cache. I'm viewing the cache stats using nscd -g to determine whether it's been used. I've also turned the debug log level up to see if I can see it hitting and the queries don't even hit nscd. nsswitch.conf # Begin /etc/nsswitch.conf passwd: files group: files shadow: files publickey: files hosts: cache files dns networks: files protocols: files services: files ethers: files rpc: files netgroup: files # End /etc/nsswitch.confenter code here nscd.conf # # /etc/nscd.conf # # An example Name Service Cache config file. This file is needed by nscd. # # Legal entries are: # # logfile <file> # debug-level <level> # threads <initial #threads to use> # max-threads <maximum #threads to use> # server-user <user to run server as instead of root> # server-user is ignored if nscd is started with -S parameters # stat-user <user who is allowed to request statistics> # reload-count unlimited|<number> # paranoia <yes|no> # restart-interval <time in seconds> # # enable-cache <service> <yes|no> # positive-time-to-live <service> <time in seconds> # negative-time-to-live <service> <time in seconds> # suggested-size <service> <prime number> # check-files <service> <yes|no> # persistent <service> <yes|no> # shared <service> <yes|no> # max-db-size <service> <number bytes> # auto-propagate <service> <yes|no> # # Currently supported cache names (services): passwd, group, hosts, services # logfile /var/log/nscd.log threads 4 max-threads 32 server-user nobody # stat-user somebody debug-level 9 # reload-count 5 paranoia no # restart-interval 3600 enable-cache passwd yes positive-time-to-live passwd 600 negative-time-to-live passwd 20 suggested-size passwd 211 check-files passwd yes persistent passwd yes shared passwd yes max-db-size passwd 33554432 auto-propagate passwd yes enable-cache group yes positive-time-to-live group 3600 negative-time-to-live group 60 suggested-size group 211 check-files group yes persistent group yes shared group yes max-db-size group 33554432 auto-propagate group yes enable-cache hosts yes positive-time-to-live hosts 3600 negative-time-to-live hosts 20 suggested-size hosts 211 check-files hosts yes persistent hosts yes shared hosts yes max-db-size hosts 33554432 enable-cache services yes positive-time-to-live services 28800 negative-time-to-live services 20 suggested-size services 211 check-files services yes persistent services yes shared services yes max-db-size services 33554432 resolv.conf # Generated by dhcpcd from eth0 nameserver 127.0.0.1 domain westell.com nameserver 192.168.1.1 nameserver 208.67.222.222 nameserver 208.67.220.220 as kind of a side note I'm using archlinux.

  Read the article

• Backup plan for linux webserver in small business?

  - by radman

  Hi, I am currently in the process of writing a backup plan for the webserver in use by my business. I am very new to this area and have a few ideas about how things should work but am unsure of what tools to use and what sort of restore process is appropriate. I'm looking for something relatively simplistic and it doesn't have to be 100% paranoid just enough to give me a reliable backup. Speed is not of the essence and there is not going to be a live fallback in place. The backup will be onto a single hdd that will be stored onsite (no option for offsite as yet). Backups will be taking place weekly. I am constrained by both time and money which is why I'm aiming for a good enough solution. Is taking an image of the webserver system drive periodically and using that as the backup appropriate? Should I be testing that the backups restore correctly every time that I perform one? This is a bit broad but what setup would you use if you were in my place, given the services I am running? Should I add additonal machines and split the services? Any advice is much appreciated! See below for server details Webserver Platform Linux Ubuntu server Running mail-server svn-server mediawiki wordpress apache-webserver Hardware single 500gb sata drive Architecture Single machine behind router (with firewall) accessible to the internet.

  Read the article

• Iptables based router inside KVM virtual machine

  - by Anton

  I have KVM virtual machine (CentOS 6.2 x64), it has 2 NIC: eth0 - real external IP 1.2.3.4 (simplified example instead of real one) eth1 - local internal IP 172.16.0.1 Now I'm trying to make port mapping 1.2.3.4:80 = 172.16.0.2:80 Current iptables rules: # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE -A PREROUTING -p tcp -m tcp -d 1.2.3.4 --dport 80 -j DNAT --to-destination 172.16.0.2:80 COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *mangle :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 But there is nothing works, I mean it does not forwards that port. Similar configuration without virtualization seems to be working. What am I missing? Thanks!

  Read the article

• how to switch to another window when Ctrl + B not works for tmux?

  - by hugemeow

  as we all know tmux is quite nice tool, but there is some scenerios that Ctrl + B cannot be used for example: i sshd to server A, and now i connect to A's tmux pty, so Ctrl + B is captured by server A. then i ssh to server B from server A, and there is also tmux running on Server B, this time, Ctrl + B only works for server A, and cannot be used by server B, so if i want to switch windows for server B, what should i do then?

  Read the article

• Same netmask or /32 for secondary IP on Linux

  - by derobert

  There appear to be (at least) two ways to add a secondary IP address to an interface on Linux. By secondary, I mean that it'll accept traffic to the IP address, and responses to connections made to that IP will use it as a source, but any traffic the box originates (e.g., an outgoing TCP connection) will not use the secondary address. Both ways start with adding the primary address, e.g., ip addr add 172.16.8.10/24 dev lan. Then I can add the secondary address with either a netmask of /24 (matching the primary) or /32. If I add it with a /24, it gets flagged secondary, so will not be used as the source of outgoing packets, but that leaves a risk of the two addresses being added in the wrong order by mistake. If I add it with /32, wrong order can't happen, but it doesn't get flagged as secondary, and I'm not sure what the bad effects of that may be. So, I'm wondering, which approach is least likely to break? (If it matters, the main service on this machine is MySQL, but it also runs NFSv3. I'm adding a second machine as a warm standby, and hope to switch between them by changing which owns the secondary IP.)

  Read the article

• Ubuntu: disable udev's persistent-net-generator.rules

  - by Luke404

  I'm using Ubuntu 12.04 LTS server edition and I am modifying /etc/udev/rules.d/70-persistent-net.rules to define my own mappings of ethernet interfaces to MAC addresses; that file is initially generated by rules in /lib/udev/rules.d/75-persistent-net-generator.rules at system installation time (or at the first boot, I actually don't know and it doesn't matter here). How can I be sure that my edited version will never ever be overwritten by anything? Removing the persistent-net-generator, as suggested on some websites, is not the Right Thing™ to do as told by comments in the file itself: it will be overwritten by any update of the udev package. I'm looking for a more formally correct way to disable it. Is it enough to just make sure that /etc/udev/rules.d/70-persistent-net.rules does exist? Maybe there are other events that could trigger its regeneration? (eg. adding or removing ethernet interfaces to the system?)

  Read the article

• What Linux platform is Ubuntu Server

  - by Graeme

  I'm just trying to get an old HP ML150 up and running to learn on. I've installed ubuntu server on it and have found the drivers are all not installed. HP has drivers but I have no clue what platform to download.This is what I have to choose from. » Novell NetWare 6.5 » Red Hat Enterprise Linux 4 (AMD64/EM64T) » Red Hat Enterprise Linux 4 (x86) » Red Hat Enterprise Linux 5 Server (x86) » Red Hat Enterprise Linux 5 Server (x86-64) » SCO OpenServer 5 » SCO OpenServer 6 » SCO UnixWare 7 » SUSE Linux Enterprise Server 10 (AMD64/EM64T) » SUSE Linux Enterprise Server 10 (x86) » SUSE Linux Enterprise Server 9 (AMD64/EM64T) » SUSE Linux Enterprise Server 9 (x86) Any suggestions? Thank you in advance guys for your help.

  Read the article

• Installing ffmpeg + dependencies on AWS Linux AMI (repo issues)

  - by HdN8

  I'm installing ffmpeg to run on an Amazon linux AMI, and have added the rpmforge repo and the dag repo. Here are some guidelines I'm using for reference: TWoZaO and Razuna The rpmforge repo has ffmpeg, but if you try to install it then it will complain that is missing dependencies (for me libSDL-1.2.so.0()(64bit)). Regardless I will install ffmpeg from svn so I can be sure to enable the options I want (namelylibx264). It seems strange to me though that SDL is not inrpmforgeordag`, and in according to both of my references above, it should be there. I tried to grab it manually from here, but it needs these dependencies, so no-go: > error: Failed dependencies: SDL = > 1.2.10-8.el5 is needed by SDL-devel-1.2.10-8.el5.x86_64 > alsa-lib-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libGL-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libGLU-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libSDL-1.2.so.0()(64bit) is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libX11-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXext-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXrandr-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXrender-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64 > libXt-devel is needed by > SDL-devel-1.2.10-8.el5.x86_64

  Read the article

• Corosync :: Restarting some resources after Lan connectivity issue

  - by moebius_eye

  I am currently looking into corosync to build a two-node cluster. So, I've got it working fine, and it does what I want to do, which is: Lost connectivity between the two nodes gives the first node '10node' both Failover Wan IPs. (aka resources WanCluster100 and WanCluster101 ) '11node' does nothing. He "thinks" he still has his Failover Wan IP. (aka WanCluster101) But it doesn't do this: '11node' should restart the WanCluster101 resource when the connectivity with the other node is back. This is to prevent a condition where node10 simply dies (and thus does not get 11node's Failover Wan IP), resulting in a situation where none of the nodes have 10node's failover IP because 10node is down 11node has "given back" his failover Wan IP. Here's the current configuration I'm working on. node 10sch \ attributes standby="off" node 11sch \ attributes standby="off" primitive LanCluster100 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.100" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive LanCluster101 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.101" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive Ping100 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive Ping101 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive WanCluster100 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.100" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive WanCluster101 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.101" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive Website0 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf" options="-DSSL" \ operations $id="Website-one" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" primitive Website1 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf.1" options="-DSSL" \ operations $id="Website-two" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" group All100 WanCluster100 LanCluster100 group All101 WanCluster101 LanCluster101 location AlwaysPing100WithNode10 Ping100 \ rule $id="AlWaysPing100WithNode10-rule" inf: #uname eq 10sch location AlwaysPing101WithNode11 Ping101 \ rule $id="AlWaysPing101WithNode11-rule" inf: #uname eq 11sch location NeverLan100WithNode11 LanCluster100 \ rule $id="RAND1083308" -inf: #uname eq 11sch location NeverPing100WithNode11 Ping100 \ rule $id="NeverPing100WithNode11-rule" -inf: #uname eq 11sch location NeverPing101WithNode10 Ping101 \ rule $id="NeverPing101WithNode10-rule" -inf: #uname eq 10sch location Website0NeedsConnectivity Website0 \ rule $id="Website0NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 location Website1NeedsConnectivity Website1 \ rule $id="Website1NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 colocation Never -inf: LanCluster101 LanCluster100 colocation Never2 -inf: WanCluster100 LanCluster101 colocation NeverBothWebsitesTogether -inf: Website0 Website1 property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1408954702" \ maintenance-mode="false" rsc_defaults $id="rsc-options" \ resource-stickiness="100" \ migration-threshold="3" I also have a less important question concerning this line: colocation NeverBothLans -inf: LanCluster101 LanCluster100 How do I tell it that this collocation only applies to '11node'.

  Read the article

• Linux VLAN Bridge

  - by raspi

  I have home network with VLANs, one for LAN, one for WLAN and one for internet. I'd like to use bridging so that instead of configuring these same VLANs to every machine, they had own VLAN ID and bridges were LAN, WLAN and internet. I've tried it but for some reason keep-alive/ttl seems to get broken because SSH sessions etc suddenly disconnects. We have this same setup working in workplace for 4+ years with 100+ customers but it's custom firewall/router hardware so accessing it is impossible. I know that it runs Linux. So what is Debian/Ubuntu default network settings doing wrong or is it just NIC driver/hw problem? I've tried to mess araund with ttl etc settings without any luck. The bad stuff is happening in the bridge because current VLAN-only setup works fine. interfaces: auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 allow-hotplug eth1 iface eth0 inet static iface eth1 inet static auto vlan111 auto vlan222 auto vlan333 auto vlan444 auto br0 auto br1 auto br2 # LAN iface vlan111 inet static vlan_raw_device eth0 # WLAN iface vlan222 inet static vlan_raw_device eth0 # ADSL Modem iface vlan333 inet static vlan_raw_device eth1 # Internet iface vlan444 inet static vlan_raw_device eth0 # LAN bridge iface br0 inet static address 192.168.0.1 netmask 255.255.255.0 bridge_ports eth0.111 bridge_stp on # Internet bridge iface br1 inet static address x.x.x.x netmask x.x.x.x gateway x.x.x.x bridge_ports eth1.333 eth0.444 bridge_stp on post-up iptables -t nat -A POSTROUTING -o br1 -j MASQUERADE pre-down iptables -t nat -D POSTROUTING -o br1 -j MASQUERADE # WLAN bridge iface br2 inet static address 192.168.1.1 netmask 255.255.255.0 bridge_ports eth0.222 bridge_stp on Sysctl: net.ipv4.conf.default.forwarding=1

  Read the article

• linux: mount old ATA disk to USB adapter

  - by 130490868091234

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

  Read the article

• nvidia driver problems after upgrading to 3.2.0-26 on Ubuntu 12.04 64bit

  - by Lev Levitsky

  After installing latest updates I can't set screen resolution higher than 1024x768; every time after the boot I get a message Could not apply the stored configuration for the monitors (Note: removing ~/.config/monitors.xml stopped the message, but not the problem) I can boot with 3.2.0-25 and the graphics look normal. Here's what I have in /var/log/apt/term.log (excerpt): Setting up linux-image-3.2.0-26-generic (3.2.0-26.41) ... Running depmod. update-initramfs: deferring update (hook will be called later) Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic Error! Problems with depmod detected. Automatically uninstalling this module. DKMS: Install Failed (depmod problems). Module rolled back to built state. run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic update-initramfs: Generating /boot/initrd.img-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.2.0-26-generic Found initrd image: /boot/initrd.img-3.2.0-26-generic Found linux image: /boot/vmlinuz-3.2.0-25-generic Found initrd image: /boot/initrd.img-3.2.0-25-generic Found linux image: /boot/vmlinuz-3.2.0-24-generic Found initrd image: /boot/initrd.img-3.2.0-24-generic Found linux image: /boot/vmlinuz-3.2.0-23-generic Found initrd image: /boot/initrd.img-3.2.0-23-generic Found linux image: /boot/vmlinuz-3.0.0-17-generic Found initrd image: /boot/initrd.img-3.0.0-17-generic Found memtest86+ image: /boot/memtest86+.bin I went to "additional drivers" and saw some updates available there, but an attempt to install them failed, leaving the following in /var/log/jockey.log (long log, pasted here). The full log won't fit in the question, so I'm showing $ fgrep 'ERROR' /var/log/jockey.log 2012-06-30 17:29:57,897 WARNING: modinfo for module vmxnet failed: ERROR: modinfo: could not find module vmxnet 2012-06-30 17:29:57,937 WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl 2012-06-30 17:29:58,072 WARNING: modinfo for module nvidia_96 failed: ERROR: modinfo: could not find module nvidia_96 2012-06-30 17:29:58,240 WARNING: modinfo for module nvidia_current failed: ERROR: modinfo: could not find module nvidia_current 2012-06-30 17:29:58,293 WARNING: modinfo for module nvidia_current_updates failed: ERROR: modinfo: could not find module nvidia_current_updates 2012-06-30 17:29:58,351 WARNING: modinfo for module nvidia_173_updates failed: ERROR: modinfo: could not find module nvidia_173_updates 2012-06-30 17:29:58,385 WARNING: modinfo for module nvidia_173 failed: ERROR: modinfo: could not find module nvidia_173 2012-06-30 17:29:58,420 WARNING: modinfo for module nvidia_96_updates failed: ERROR: modinfo: could not find module nvidia_96_updates 2012-06-30 17:29:58,455 WARNING: modinfo for module ath_pci failed: ERROR: modinfo: could not find module ath_pci 2012-06-30 17:29:58,478 WARNING: modinfo for module fglrx_updates failed: ERROR: modinfo: could not find module fglrx_updates 2012-06-30 17:29:58,531 WARNING: modinfo for module fglrx failed: ERROR: modinfo: could not find module fglrx 2012-06-30 17:29:58,588 WARNING: modinfo for module omapdrm_pvr failed: ERROR: modinfo: could not find module omapdrm_pvr 2012-06-30 17:29:59,537 WARNING: modinfo for module nvidia_current failed: ERROR: modinfo: could not find module nvidia_current 2012-06-30 17:29:59,613 WARNING: modinfo for module nvidia_173_updates failed: ERROR: modinfo: could not find module nvidia_173_updates 2012-06-30 17:29:59,686 WARNING: modinfo for module nvidia_173 failed: ERROR: modinfo: could not find module nvidia_173 2012-06-30 17:29:59,764 WARNING: modinfo for module nvidia_current_updates failed: ERROR: modinfo: could not find module nvidia_current_updates 2012-06-30 17:30:29,544 WARNING: modinfo for module nvidia_current_updates failed: ERROR: modinfo: could not find module nvidia_current_updates 2012-06-30 17:30:29,545 ERROR: XorgDriverHandler.enable(): package or module not installed, aborting I'm not sure if it's a bug, as the first log shows some errors. What can I try?

  Read the article

• file corruption on read/write 2.6.32-22-server (happens across many kernels)

  - by Jonathan

  Hi Guys, I'm having an issue where after the server has been up for a period of time (~week/few days) the server will start reading corrupt data. For instance when I run a sha1sum of a file after a fresh boot it remains the same. However after a while I will start to get segfaults and from then on whenever I read this file I get a different sha1sum. I've checked S.M.A.R.T with long tests and I've run an extended memtest86+(12 passes) My lspci is as follows: 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon HD 3300 Graphics 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller 02:00.0 Ethernet controller: Atheros Communications Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0) 03:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. Device 3403 I could really use some help on this, do you have any idea what could cause this? It's really frustrating me as it seems to trigger entirely randomly and will not go away until I reboot. I'm also use KVM for virtualization as well as MD for software RAID on this server and the processor is a Phenom II X4 965. I don't believe it's the software raid however as this affects files also hosted on non-raid partitions so I don't know.

  Read the article

• Pip installs on Archlinux fails to build egg

  - by stmfunk

  I was trying to install nltk on my Archlinux server but it repeatedly fails with the following error output /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'entry_points' warnings.warn(msg) /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'zip_safe' warnings.warn(msg) /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'test_suite' warnings.warn(msg) usage: setup.py [global_opts] cmd1 [cmd1_opts] [cmd2 [cmd2_opts] ...] or: setup.py --help [cmd1 cmd2 ...] or: setup.py --help-commands or: setup.py cmd --help error: invalid command 'bdist_egg' /tmp/pip_build_root/nltk/distribute-0.6.21-py3.3.egg Traceback (most recent call last): File "./distribute_setup.py", line 143, in use_setuptools raise ImportError ImportError During handling of the above exception, another exception occurred: Traceback (most recent call last): File "", line 16, in File "/tmp/pip_build_root/nltk/setup.py", line 23, in distribute_setup.use_setuptools() File "./distribute_setup.py", line 145, in use_setuptools return _do_download(version, download_base, to_dir, download_delay) File "./distribute_setup.py", line 125, in _do_download _build_egg(egg, tarball, to_dir) File "./distribute_setup.py", line 116, in _build_egg raise IOError('Could not build the egg.') OSError: Could not build the egg. ---------------------------------------- Cleaning up... Command python setup.py egg_info failed with error code 1 in /tmp/pip_build_root/nltk Storing complete log in /root/.pip/pip.log This error is also occurring for matplotlib buts thats the only other library I found it to fail on so far. pyyaml installs fine. The install works perfectly under virtualenv on my mac which is using python 2.7 but the server is using python 3.3. Any help is appreciated.

  Read the article

< Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >