Search Results

Search found 27142 results on 1086 pages for 'control structure'.

Page 915/1086 | < Previous Page | 911 912 913 914 915 916 917 918 919 920 921 922  | Next Page >

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• Shut Out of XP - No Admin Password or CDR

  - by ashes999

  I inherited an old WinXP/Linux dual-boot machine from the stoneage. Because it has Linux, the regular boot process is replaced with the Fedora boot loader; I cannot, therefore, press F8 strategically to tell my PC to boot from CD. Even if I could, it's a moot point; the CDR doesn't seem to recognize any CDs. To make things worse, there's no option to network boot. The original user is probably long gone; I don't know the password for any of the Administrator group users. I can login using my corp account, but that's unprivileged on this machine. Since I'm not an admin, I can't do crazy things, like looking at boot.ini. Or deleting files. I only have 500MB free on my C drive. I'm pretty sure I can't boot from a USB, since I didn't see any settings for this in my BIOS. How can I get admin access for my user? Edit: Things I've tried: Boot from CD (CD not recognized) Launch CD from XP (CD not recognized) Install Daemon Tools Lite so I can install from an ISO -- don't have admin privileges XP password recovery tool -- requires admin privileges Adding an admin user -- no access to Control Panel Users since I'm not an admin Logging in as both the admin users on the system (trying some standard passwords) Using Fedora to chntpw (the Fedora version installed is ancient -- 2.7)

  Read the article

• Linux: prevent outgoing TCP flood

  - by Willem

  I run several hundred webservers behind loadbalancers, hosting many different sites with a plethora of applications (of which I have no control). About once every month, one of the sites gets hacked and a flood script is uploaded to attack some bank or political institution. In the past, these were always UDP floods which were effectively resolved by blocking outgoing UDP traffic on the individual webserver. Yesterday they started flooding a large US bank from our servers using many TCP connections to port 80. As these type of connections are perfectly valid for our applications, just blocking them is not an acceptable solution. I am considering the following alternatives. Which one would you recommend? Have you implemented these, and how? Limit on the webserver (iptables) outgoing TCP packets with source port != 80 Same but with queueing (tc) Rate limit outgoing traffic per user per server. Quite an administrative burden, as there are potentially 1000's of different users per application server. Maybe this: how can I limit per user bandwidth? Anything else? Naturally, I'm also looking into ways to minimize the chance of hackers getting into one of our hosted sites, but as that mechanism will never be 100% waterproof, I want to severely limit the impact of an intrusion. Cheers!

  Read the article

• VBA + Polymorphism: Override worksheet functions from 3rd party

  - by phi

  my company makes extensive use of a data provider using a (closed source) VBA plugin. In principal, every query follows follows a certain structure: Fill one cell with a formula, where arguments to the formula specify the query the range of that formula is extended (not an arrray formula!) and cells below/right are filled with data For this to work, however, a user has to have a terminal program installed on the machine, as well as a com-plugin referenced in VBA/Excel. My Problem These Excelsheets are used and extended by multiple users, and not all of them have access to the data provider. While they can open the sheet, it will recalculate and the data will be gone. However, frequent recalculation is required. I would like every user to be able to use the sheets, without executing a very specific set of formulas. Attempts remove the reference on those computers where I do not have terminal access. This generates a NAME error i the cell containing the query (acceptable), but this query overrides parts of the data (not acceptable) If you allow the program to refresh, all data will be gone after a failed query Replace all formulas with the plain-text result in the respective cells (press a button and loop over every cell...). Obviously destroys any refresh-capabilities the querys offer for all subsequent users, so pretty bad, too. A theoretical idea, and I'm not sure how to implement it: Replace the functions offered by the plugin with something that will be called either first (and relay the query through to the original function, if thats available) or instead of the original function (by only deploying the solution on non-terminal machines), which just returns the original value. More specifically, if my query function is used like this: =GETALLDATA(Startdate, Enddate, Stockticker, etc) I would like to transparently swap the function behind the call. Do you see any hope, or am I lost? I appreciate your help. PS: Of course I'm talking about Bloomberg... Some additional points to clarify issues raise by Frank: The formula in the sheets may not be changed. This is mission-critical software, and its way too complex for any sane person to try and touch it. Only excel and VBA may be used (which is the reason for the previous point...) It would be sufficient to prevent execution of these few specific formulas/functions on a specific machine for all excel sheets to come This looks more and more like a problem for stackoverflow ;-)

  Read the article

• Trouble getting latest version of Git

  - by TheMethod

  I am using Ubuntu 10.04 LTS. I'm looking at using git as source control for personal projects and Github as a remote repository. I was having trouble pushing a commit to my remote github repo getting the following error message: The requested URL returned error: 403 while accessing https://github.com/Jstall/helloworld.git/info/refs When I did some digging I found that the problem could be me not having the latest version of Git. When I did a --version I found that I have version 1.7.0.4 locally. So I tried to update git using: sudo apt-get install git but get the following error: Reading package lists... Done Building dependency tree Reading state information... Done Package git is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package git has no installation candidate I've tried running: sudo apt-get update and trying again but it didn't seem to make a difference. I'm not sure if it's relevant but I'm also getting a couple of 404's when I run update: Err http://wine.budgetdedicated.com edgy/main Packages 404 Not Found Fetched 4,117B in 0s (5,142B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/edgy/universe/binary-i386/Packages.gz 404 Not Found [IP: 91.189.91.15 80] W: Failed to fetch http://wine.budgetdedicated.com/apt/dists/edgy/main/binary-i386/Packages.gz 404 Not Found I'm not sure when I should try next. Could anyone suggest a course of action to get this resolved? Any advice would be appreciated. Thanks much!

  Read the article

• My Windows 7 has suddenly stopped displaying Unicode symbols

  - by Felix Dombek

  For some strange reason, my computer suddenly doesn't show certain unicode characters anymore! I have no idea what happened. Affected applications include Windows Explorer (should be Japanese characters), Google Chrome (should be a heart), and Winamp (should be stars): Russian, German etc. characters are displayed normally. Chrome also displays Japanese script on websites, but not in the GUI. How can I fix it? Update: I have tried to use System Restore to fix it. I needed to go back in time quite a while because the most recent restore points didn't solve it so I used one from the middle of November. After that restore, Unicode symbols were displayed again. Then I updated my system with Windows Update again because those were removed during the restore. After that, the error occurred again! I then did a restore to a point before my new updates, but the error persists, and the old restore point (which I used before) is gone and there are currently no other snapshots of the system. Any suggestions on what to do now? Update 2: I could find a workaround: Control Panel ? Region and Language ? Administration ? Change Language for Unicode-incompatible programs to Japanese (Japan). All mentioned programs display their symbols correctly again. However, I don't consider this a fix because these programs are not usually Unicode-incompatible, and it also leads to some (non-serious) artifacts in some programs. I still welcome an answer that tells me what went wrong here and how to fix the issue.

  Read the article

• Nginx : Proper use of limit_req_zone and limit_req

  - by xperator

  I have 2 website running on VPS. Their purpose is sharing music files and publishing news. Both of them use wordpress. What I am trying is that I want to prevent little hackers from flooding the webserver and putting stress on the server to make it crash. The problem is that after using limit_req_zone and limit_req my website became very slow. Browsing Wordpress control panel takes a long long time. I tried changing values but it didn't improve much. I guess the problem is Wordpress because it's the only script I am using on both front and back end. Here is the last setting which seems to be more responsive than others : limit_req_zone $binary_remote_addr zone=flood:5m rate=10r/m; location ~ \.php$ { limit_req zone=flood burst=100 nodelay; } What are the optimal values that should be used in my case (wp) ? I want the website have it's normal behavior, On the other hand stopping lifeless people from flooding. Another question, Is it safe and enough to use limit_req only on php files ?

  Read the article

• Keep permalinks in Wordpress

  - by Remus Rigo

  Is there any way to set my permalinks to keep their exact link. If I have a post like this one http://blog.rigo.ro/?p=11, then I would like that every time I edit the post to keep this link. I have installed the Revision Control plugin and I set it to do not keep revisions. Any ideea how to do this? I want to keep this format of links. Edit: I took a look again, the permalinks keep their links, but every time I edit it adds a new version to the database and the next post will have a higher number. If I edit my current post for 3 times (blog.rigo.ro/?p=11) the next post will be blog.rigo.ro/?p=14. Now, my question is how can I keep all my post and edits clean, one post/more edits = one entry in the database, so if I have. 10 post on my site and I edit them, I would like that my permalinks to be from 1 to 10. PS: I don't want to edit my database manually, is there any plugin to do this?

  Read the article

• how to block spam email using Microsoft Outlook 2011 (Mac)?

  - by tim8691

  I'm using Microsoft Outlook 2011 for Mac and I'm getting so much spam I'm not sure how to control it. In the past, I always applied "Block Sender" and "Mark as Junk" to any spam email messages I received. This doesn't seem to be enough nowadays. Then I've started using Tools Rules to create rules based on subject, but the same spammer keeps changing subject lines, so this isn't working. I've been tracking the IP addresses they also seem to be changing with each email. Is there any key information I can use in the email to apply a rule to successfully place these spam emails in the junk folder? I'm using a "Low" level of junk email protection. The next higher level, "high", says it may eliminate valid emails, so I prefer not to use this option. There's maybe one or two spammers sending me emails, but the volume is very high now. I'm getting a variation of the following facebook email spam: Hi, Here's some activity you have missed. No matter how far away you are from friends and family, we can help you stay connected. Other people have asked to be your friend. Accept this invitation to see your previous friend requests Some variations on the subject line they've used include: Account Info Change Account Sender Mail Pending ticket notification Pending ticket status Support Center Support med center Pending Notification Reminder: Pending Notification How do people address this? Can it be done within Outlook or is it better to get a third party commercial software to plug-in or otherwise manage it? If so, why would the third party be better than Outlook's internal tools (e.g. what does it look for in the incoming email that Outlook doesn't look at)?

  Read the article

• How to prioritize openvpn traffic?

  - by aditsu

  I have an openvpn server, with one network interface. VPN traffic is extremely slow. I tried to do traffic control with this configuration (currently): qdisc del dev eth0 root qdisc add dev eth0 root handle 1: htb default 12 class add dev eth0 parent 1: classid 1:1 htb rate 900mbit #vpn class add dev eth0 parent 1:1 classid 1:10 htb rate 1500kbit ceil 3000kbit prio 1 #local net class add dev eth0 parent 1:1 classid 1:11 htb rate 10mbit ceil 900mbit prio 2 #other class add dev eth0 parent 1:1 classid 1:12 htb rate 500kbit ceil 1000kbit prio 2 filter add dev eth0 protocol ip parent 1:0 prio 1 u32 match ip sport 1194 0xffff flowid 1:10 filter add dev eth0 protocol ip parent 1:0 prio 2 u32 match ip dst 192.168.10.0/24 flowid 1:11 qdisc add dev eth0 parent 1:10 handle 10: sfq perturb 10 qdisc add dev eth0 parent 1:11 handle 11: sfq perturb 10 qdisc add dev eth0 parent 1:12 handle 12: sfq perturb 10 But it's still extremely slow. I have an imaps connection that keeps transferring data continuously (I successfully limited the rate) but with openvpn I can't seem to get more than about 100kbit/s The internet connection speed is about 3mbit/s (symmetric) What could be the problem? Does the sport filter work for udp?

  Read the article

• Windows ACL inheritance issues for FTP server and automated tools

  - by Martin Sall

  I have set up Cerberus FTP server. By default, Cerberus FTP service runs under SYSTEM ACCOUNT. Also I have some console applications which run as scheduled tasks. They are running under a dedicated "Utilities" user account which has "Log on as batch job" permissions. These console applications take uploaded FTP files, process them and then move them to some dedicated archive folder. The problem is that my console apps are throwing Security exceptions when trying to acces the uploaded files. I tried to give the Full control permissions on the ftproot folder for my "Utilities" account and I have checked that "Replace all Child object permissions with inheritable permissions from this object" checkbox, but it affects only current files. When new files are uploaded, they again are not accessible by my "Utilities" account. I tried to go another way and put Cerberus FTP service under "Utilities" account. Then I also needed to give "Utilities" account permissions on Cerberus Data folder in ProgramData. Still no luck - after this operation, Cerberus internal SOAP web service stopped working (although everything else seems to work). I need that SOAP service to be available, so running the Cerberus FTP under "Utilities" account seems to be not an option. Unless I find out, what else do I need to set up for that "Utilities" account to stop Cerberus from complaining. I guess, Cerberus is uploading files to some temporary folder and so those files get the permissions form that folder and keep the same permissions even after moved to the ftproot. What would be the right solution for this which would grant Cerberus FTP server and the "Utilities" account minimal needed permissions to access the contents of the ftproot folder?

  Read the article

• Why Wireshark does not recognize this HTTP response?

  - by Alois Mahdal

  I have a trivial CGI script that outputs simple text content. It's written in Perl and using CGI module and it specifies only the most basic headers: print $q->header( -type => 'text/plain', -Content_length => $length, ); print $stuff; There's no apparent issue with functionality, but I'm confused about the fact that Wireshark does not recognize the HTTP response as HTTP--it's marked as TCP. Here is request and response: GET /cgi-bin/memfile/memfile.pl?mbytes=1 HTTP/1.1 Host: 10.6.130.38 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: cs,en-us;q=0.7,en;q=0.3 Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 200 OK Date: Thu, 05 Apr 2012 18:52:23 GMT Server: Apache/2.2.15 (Win32) mod_ssl/2.2.15 OpenSSL/0.9.8m Content-length: 1048616 Keep-Alive: timeout=5, max=100 Connection: Keep-Alive Content-Type: text/plain; charset=ISO-8859-1 XXXXXXXX... And here is the packet overview (Full packet is here on pastebin) No. Time Source srcp Destination dstp Protocol Info tcp.stream abstime 5 0.112749 10.6.130.38 80 10.6.130.53 48072 TCP [TCP segment of a reassembled PDU] 0 20:52:23.228063 Frame 5: 1514 bytes on wire (12112 bits), 1514 bytes captured (12112 bits) Ethernet II, Src: Dell_97:29:ac (00:1e:4f:97:29:ac), Dst: Dell_3b:fe:70 (00:24:e8:3b:fe:70) Internet Protocol Version 4, Src: 10.6.130.38 (10.6.130.38), Dst: 10.6.130.53 (10.6.130.53) Transmission Control Protocol, Src Port: http (80), Dst Port: 48072 (48072), Seq: 1, Ack: 330, Len: 1460 Now when I see this in Wireshark: there's usual TCP handshake then the GET request shown as HTTP with preview then the next packet contains the response, but is not marked as an HTTP response--just a generic "[TCP segment of a reassembled PDU]", and is not caught by "http.response" filter. Can somebody explain why Wireshark does not recognize it? Is there something wrong with the response?

  Read the article

• Win7 VM @ ESXi Server @ VMWorkstation (Win7) - ping works only from VM -> HostOS, not vice versa

  - by DK2000

  right now I'm toying around with VM Ware stuff and not having any pcs then my laptop I decided to run an ESXi Server inside of VWmware Workstation. I was just curios to see if the server would allow to setup and run a VM. And after some tweaking there it was, working like a charm. Okay not that fast but startin' the VM from vSphere and "opening a console" gave my direct access to that VM. Now I wanted to see if I could ping the host from the VM (VM Workstation Network is set to "host only"). And it worked, at least from the VM I could ping the ESXi server and the host. From the host I am able to ping the ESXi Server but I can't ping the VM! I asked myself anyway where the VM got its ip adress from. At the DCHPs IP there is at no machine after all. I even tried to use that DHCP adress for my Host and it didn't work out. You can see my settings from the screenshot here (it's pretty wide so just a link): http://yfrog.com/n4desktopfeop The only thing that got me thinking was when I once changed the ESXi's IP from 192.168.92.137 to 192.168.0.137. I still was able to connect to the ESXi server via its new IP but when I tried to run the VM console from vSphere I got an error after a while that said "couldnt connect to 192.168.92.137:903". So vSphere connects just through a port of the ESXi server to the VM?!? Could I setup a Linux VM to use it as a DHCP that I'd at least have control over the IPs that are given. Which lowest end linux could be used for this purpose?!? Thank you for your time! :)

  Read the article

• mkfs Operation Takes Very Long on Linux Software Raid 5

  - by Elmar Weber

  I've set-up a Linux software raid level 5 consisting of 4 * 2 TB disks. The disk array was created with a 64k stripe size and no other configuration parameters. After the initial rebuild I tried to create a filesystem and this step takes very long (about half an hour or more). I tried to create an xfs and ext3 filesystem, both took a long time, with mkfs.ext3 I observed the following behaviour, which might be helpful: writing inode tables runs fast until it reaches 1053 (~ 1 second), then it writes about 50, waits for two seconds, then the next 50 are written (according to the console display) when I try to cancel the operation with Control+C it hangs for half a minute before it is really canceled The performance of the disks individually is very good, I've run bonnie++ on each one separately with write / read values of around 95 / 110MB/s. Even when I run bonnie++ on every drive in parallel the values are only reduced by about 10 MB. So I'm excluding hardware / I/O scheduling in general as a problem source. I tried different configuration parameters for stripe_cache_size and readahead size without success, but I don't think they are that relevant for the file system creation operation. The server details: Linux server 2.6.35-27-generic #48-Ubuntu SMP x86_64 GNU/Linux mdadm - v2.6.7.1 Does anyone has a suggestion on how to further debug this?

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• How to setup firewall to allow internet connection sharing via Wifi USB stick?

  - by hannanaha

  I have a Windows8 computer linked to the internet via an ethernet cable ("Ethernet" network connection). I have attached to it a DLink Wifi USB stick, and I'm trying to share the main PC's internet connection with my Android phone via a local wifi network. I am using the following batch file to set up this network: netsh wlan set hostednetwork mode=allow ssid=MyWifiName key=password keyUsage=persistent netsh wlan start hostednetwork After I run this script, I can see a new network connection appear in "Control Panel\Network and Internet\Network Connections" named "Local Area Connection *12", and I can see "MyWifiName" on the Android phone. The device name for this connection on the PC is "Microsoft Hosted Network Virtual Adapter". I also set up the "Ethernet" connection to share Internet with "Local Area Connection *12". However, the Android phone usually doesn't manage to obtain an IP from the wireless network, and when it does, there still seems to be no connectivity to the internet. When I turn off the Windows Firewall completely, or even just for "Local Area Connection *12", the Android connection is perfect. My questions are: How should I set up the Windows firewall to allow the phone to connect properly? Is there a specific rule I need to add to the Windows firewall advanced settings? [Note: the above method worked great in Windows 7, without any specific tinkering with the firewall]. Is it safe to turn off the firewall specifically for the "Local Area Connection *12" (the wifi connection) if the main Ethernet connection is still protected by the firewall? Thanks in advance.

  Read the article

• Authority Information Access local path being ignored

  - by Kevin

  I have a CA set up in Server 2008 R2, and generally it is working, but I can't control the local path/filename it writes its own certificate to for the Authority Information Access publishing. Here's a screen shot of the dialog I'm trying to set this on: From these settings I would expect to get the file: C:\Windows\system32\CertSrv\CertEnroll\DAMNIT.crt But instead I get: C:\Windows\system32\CertSrv\CertEnroll\SERVER.domain.com_My Issuing Authority(1).crt Of course, the actual change shown wouldn't be very useful, but it's illustrative; no matter what path/filename I use, it always lands up in the same place and with the same name. I actually wanted to change the name from <ServerDNSName>_<CaName><CertificateName>.crt to <CaName><CertificateName>.crt, since the latter corresponds to the HTTP URL whereas the former does not. Admittedly, I haven't set up many CAs so perhaps I'm just deluded as to what this dialog is supposed to be setting, but if so this is notoriously bad UI design. (Incidentally, I have a couple other complaints with the same dialog.) What's going on here and is there some way to get the filename pattern I want?

  Read the article

• Using virtualization infrastructure for J2EE application distribution- viable alternative?

  - by Dan

  Our company builds custom J2EE web solutions. At the moment, we use standard J2EE distribution mechanisms (ear/war archives). Application servers are generally administered by our clients' IT departments and since we do not have complete control over the environment, a lot of entropy can be introduced into the solution. For example: latest app. server patch not applied conflicting third party libraries inside the app. server root server runtime and tuning parameters not configured (for example, number of connections in database pool) We are looking into using virtualization infrastructure for J2EE application distribution. Instead of sending the ear/war archive, we’d send image with application server node and our application preinstalled. Some of the benefits are same as using with using virtualization infrastructure in general, namely better use of hardware resources. For us, it reduces the entropy of hosting infrastructure - distributing VM should be less affected by hosting environment. So far, the downside I see can be in application server licenses, here they will have to use dedicated servers for our solution, but this is generally already done that way. Also, there is a complexity with maintaining virtualization infrastructure, but this is often something IT departments have more experience with than with administering and fine-tuning J2EE solutions. Anyone has experience with this model? What are the downsides? Will we not just replace one type of complexity with other?

  Read the article

• Unextending Sharepoint 2007 Web Application from a zone

  - by dunxd

  When our Sharepoint was migrated from Sharepoint 2003 to Sharepoint 2007 (both fully paid versions), the consultants who carried it out extended each web app into two IIS sites/zones (e.g. the original Web App was http://intranet, then http://newintranet and http://intranet would be created for Sharepoint 2007 - each with its own IIS site). The idea was that during the migration period we would set up DNS to point the old url to SP2003 servers and the new one to SP2007, then once the migration was complete, do a DNS change so the SP2007 would recieve the requests to the http://intranet type URLs. Unfortunately the contractors did not tidy up the application extensions and IIS sites after the migration, and for some time both URLs were in use, resulting in many document links pointing to the http://newintranet type URLs. This means I need to maintain these URLs. Due to a rejig of organisation structure we now need to relocate some Sharepoint sites, and I'd like to use the RDA Collaboration Sharepoint URL Redirector feature. However a limitation of this is that it doesn't work for Web Applications which have been extended into multiple zones. So I have a need to tidy up the situation that our consultants left behind. I think the right thing to do is use the "Remove Sharepoint from IIS Web Site" page in Central Admin to remove the zone for the newintranet type sites, and select the option to also delete the IIS site. That should result in having no IIS sites listening for http://newintranet type URLs. Is this the right procedure? Once I have done that I need to set up Sharepoint to receive requests sent to the http://newintranet type URLs so they will continue to work. I am not sure if I should do this: using Alternative Access Mappings or, by adding a host header to the IIS site or, creating a non Sharepoint IIS site for each http://newintranet type URL, and use IIS redirection to forward the requests to the new URL using variables to pass the path to the Sharepoint site. Does anyone have any thoughts on these options, or any other way of achieving this? Sharepoint 2007 is running on Windows 2003 with IIS6. We don't currently have plans/budget to upgrade to Sharepoint 2010.

  Read the article

• scalable yet doable small-medium office network

  - by Jared

  Hello, I'm studying up with both Microsoft and Cisco literature and I must say, my head is starting to get clustered up (pun intended). I've made a quick network diagram of a theoretical company... Company1 owns Company 2 and Company 3, which are all under separate rooms and networks, but must be able to share a few resources such as files or printers. Given the amount of info out there and best practices, I thought about posting here to get suggestions and see what would the pro's do. I can read and read all day and implement on my own, but if I dont get some outside input, how will I know if I'm doing something wrong, right? anyway, please take a look and see if this is an over-complicated network or a lackluster design for a small-medium company of about 35 people and lets say they will be double that number by end of the year... :) Using win2k3, esxi, windows xp. FCS - forefront client security, ACS - access control system, SPCWK - spiceworks, XCH - Exchange Im not allowed to post an image yet, so here's the link ---- GLIFFY IMAGE Flame suit is on just in case people get mad at me for making an "abomination". I'd really want to get the general overview properly before I dive into the more complicated things

  Read the article

• Understanding encryption Keys

  - by claws

  Hello, I'm really embarrassed to ask this question but its the fact that I don't know anything about encryption. I always avoided it. I don't understand the concept of encryption keys (public key, private key, RSA key, DSA key, PGP Key, SSH key & what not) . I did encounter these in regular basis but as I said I always avoided them. Here are few instances where I encountered: Creating Account: A public RSA or DSA key will be needed for an account. Send the key along with your desired account name to [email protected] I really don't know what are RSA/DSA or How to get their keys? Do I need to register some where for that? Mailing: I'm unable to recall exactly but I've seen some mails have some attachments like signature or the mail footer will have something called PGP signature etc.. I really don't get its concept. GIT Version control: I created account in assembla.com (for private GIT repo) and it asked me to enter "SSH keys" to my profile. Where am I gonna get these? Why do I need it? Isn't SSH related to remote login (like remote desktop or telnet)? How are these two SSHs related & differ? I don't know in how many more situations I'm going to encounter these things. I'm really confused and have no clue about where to start & how to proceed to learn these things. Kindly someone point me in correct direction. Note: I've absolutely zero interested in encryption related topics. So, there is no way I'm going to read a graduate level book on this subject. I just want to clear my concepts without going into much depth.

  Read the article

• Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

  - by Matt Taylor

  I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

  Read the article

• Can I make TCP/IP session to run less than 60 seconds?

  - by par

  Our server is overloaded with TCP/IP sessions, we have 1200 - 1500 of them. Most of them are hanging in TIME_OUT state. It turns out that a connection in TIME_OUT state occupies a socket until 60 second time-out is elapsed. The problem is that the server gets unresponsive and many clients are not getting served. I have made a simple test: download an XML file from the server with Internet Explorer 8.0 The download finishes in a fraction of second. But then I see that the TCP/IP connection is hanging in TIME_OUT state for 60 seconds. Is there any way to get rid of TIME_OUT waiting or make it less to free the socket for new connections? I understand why TCP/IP connection enters TIME_OUT state, but I don't understand why Internet Explorer does not close the connection after the XML file download is over. The details. Our server runs web service written in Perl (mod-perl). The service provides weather data to clients. Client is a Flash appication (actually Flash ActiveX control embedded in Windows application). OS: Ubuntu Apache "Keep Alive" option is set to 0

  Read the article

• Flickering dual screens in Virtual Box Ubuntu 13.10 Guest

  - by alexleonard

  I have Ubuntu 13.10 x64 installed as a guest in VirtualBox (under a Windows 8.1 host) and have the settings for the virtual machine setup to run with a monitor count of 2, 128MB video memory and 3D acceleration enabled. In my guest I have the virtual box additions installed (which allowed me to have two 1920x1080 screens). Here's a screenshot of my VM settings. My laptop is an Asus N550JV which has both Intel's HD Graphics 4600 GPU and Nvidia's GeForce GT 750M. By default though I believe the Intel GFX card is being used to render the VM. When I boot up the VM it loads perfectly on dual screens, however whenever I move the mouse from one screen to the other (I have a Dell S2340L running over a HDMI connection as a second screen) the screen flickers. I've tried a variety of settings changes in both Ubuntu and the VM settings, but cannot seem to stop this screen flicker. I also used the NVidia control panel in Windows to force the dedicated graphics card to always be used but found that the display driver sometimes crashed whilst working in the VM, resulting in my VM session being destroyed, so I figured it's better to stick with the Intel GFX as that appears to be more stable. I also tried without 3D acceleration but that was much worse, and if I ran the VM with a low amount of graphics memory it really struggled. Here's my dmesg output: http://pastebin.com/1LJuYWMj (not sure if this is helpful in this situation). I read some posts suggesting changes to /etc/X11/xorg.conf but I don't appear to have an xorg.conf file. There were also a few posts (though related to Synergy) suggesting running xset -dpms but this command doesn't appear to have had any effect for me. As an additional note, I'm finding that window drawing in the guest is a little laggy/glitchy. For example, quickly scrolling through a web page may result in parts of the viewport displaying original content. Certainly I notice drawing issues most in the web browser, but it also impacts other software with parts of the window not being drawn when, say, switching between accounts in thunderbird. Any suggestions greatly appreciated!

  Read the article

• Installing Windows Management Framework 3.0 basically destroyed WMI, how can I fix it without reinstalling the O.S.?

  - by Massimo

  Related, of course, to this question. Before discovering it was somewhat... dangerous, I installed Windows Management Framework 3.0 on a number of Windows Server 2008 R2 SP1 servers, and WMI got completely trashed on all of them. This is what the WMI namespace looks like on a normal server (this is from Server Manager - Configuration - WMI Control): This is what it looks like after installing WMF 3.0: Yeah. Everything except WMF 3.0's new features is gone. Needless to say, nothing seems to work anymore on those servers. And no, this is not due to some strange installation error, this happened on three servers which were perfectly working before installing WMF 3.0, and on all of them the installation completed succesfully. Admittedly, one of them had a somewhat complex setup (various System Center products and SQL Server instances)... but two of them are just plain standard domain controllers which do nothing else at all. How can I fix this mess without having to reinstall the O.S. on these servers? And why did it happen in the first place?

  Read the article

< Previous Page | 911 912 913 914 915 916 917 918 919 920 921 922  | Next Page >