Search Results

Search found 28301 results on 1133 pages for 'external process'.

Page 918/1133 | < Previous Page | 914 915 916 917 918 919 920 921 922 923 924 925  | Next Page >

  • Mirror a RAID0 volume

    - by Ghostrider
    I have two SSD running in RAID0. The capacity and speed are just great. I use Windows Home Server to do incremental daily backups. This is fine and well and I've successfully restored from these backups. However. When one of the disks physically died. I was stuck without a working system until the replacement arrives so that I can restore the array from backup. WHS restoration takes about 5 hours which basically means that I'm losing entire day for the process. Is it possible to set up kind of a recovery volume for the RAID array? Use a single mechanical HDD that would be updated with the exact clone of the RAID array on a daily basis. This way if the array goes offline for some reason, I can just boot from the mechanical HDD, lose some perf but will still be able to work. The machine in question runs Windows 7. Creating RAID01 is not an option because of the high price of the SSD and the fact that it still doesn't protect against failure of RAID controller. Is there any way it can be set up?

    Read the article

  • Switch Windows 8 from a hybrid MBR/GPT => GPT only on Macbook Pro Retina

    - by Sid
    I used DiskUtility+Bootcamp Wizard to setup my hard drive for Windows 8 (final MSDN). Somewhere in that process, the Apple tools turned my GPT disk into a hybrid MBR/GPT. All my 4 primary MBR partitions are used up, so when I try turning on Bitlocker in Windows 8, it complains about not finding a System drive. I know on Windows 8 the Bitlocker setup tries to create the 200(?)MB system partition if it's missing. However with all 4 partitions filled I suspect it can't create system drive = it can't find it = throws back an error like "BitLocker Setup could not find a target system drive. You may need to manually prepare your drive for BitLocker". I've already tried disabling hibernation, swap file etc. Now I'm thinking that if I were to get rid of the MBR scheme altogether, perhaps I can be alright within the GPT world without MBR's 4 primary partitions limit. So, how can I get rid of the MBR tables on the hybrid scheme in a manner that still leaves Mac OS and Windows 8 in working conditions? Details: Hardware is the MacbookPro Retina. Primary MBR partitions are consumed as follows: EFI partition HFS+ partition (=encrypted, therefore ="Apple_CoreStorage") HFS+ partition (Recovery partition, contains unencrypted Mac bootloader) NTFS partition (Windows8 all-in-one partition) diskutil list output sid-mbpr:~ sid$ diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *251.0 GB disk0 1: EFI 209.7 MB disk0s1 2: Apple_CoreStorage 160.0 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 4: Microsoft Basic Data Win8 90.1 GB disk0s4 GPT vs MBR addresses sid-mbpr:~ sid$ sudo gptsync /dev/rdisk0 Password: Current GPT partition table: # Start LBA End LBA Type 1 40 409639 EFI System (FAT) 2 409640 312909639 Unknown 3 312909640 314179175 Mac OS X Boot 4 314179584 490233855 Basic Data Current MBR partition table: # A Start LBA End LBA Type 1 1 409639 ee EFI Protective 2 409640 312909639 ac Apple RAID 3 312909640 314179175 ab Mac OS X Boot 4 * 314179584 490233855 07 NTFS/HPFS Status: GPT partition of type 'Unknown' found, will not touch this disk.** **: Ignore this message, the gptsync tool is old and doesn't understand the UUID for "Apple_CoreStorage" / FileVault2 partitions. Since LBA addresses are alright, safe to ignore this message.

    Read the article

  • Windows 7 Bluescreen: IRQ_NOT_LESS_OR_EQUAL | athrxusb.sys

    - by wretrOvian
    I'd left my system on last night, and found the bluescreen in the morning. This has been happening occasionally, over the past few days. Details: ================================================== Dump File : 022710-18236-01.dmp Crash Time : 2/27/2010 8:46:44 AM Bug Check String : DRIVER_IRQL_NOT_LESS_OR_EQUAL Bug Check Code : 0x000000d1 Parameter 1 : 00000000`00001001 Parameter 2 : 00000000`00000002 Parameter 3 : 00000000`00000000 Parameter 4 : fffff880`06b5c0e1 Caused By Driver : athrxusb.sys Caused By Address : athrxusb.sys+760e1 File Description : Product Name : Company : File Version : Processor : x64 Computer Name : Full Path : C:\Windows\minidump\022710-18236-01.dmp Processors Count : 2 Major Version : 15 Minor Version : 7600 ================================================== HiJackThis ("[...]" indicates removed text; full log [posted to pastebin][1]): Logfile of Trend Micro HijackThis v2.0.2 Scan saved at 8:49:15 AM, on 2/27/2010 Platform: Unknown Windows (WinNT 6.01.3504) MSInternet Explorer: Internet Explorer v8.00 (8.00.7600.16385) Boot mode: Normal Running processes: C:\Windows\DAODx.exe C:\Program Files (x86)\Asus\EPU\EPU.exe C:\Program Files\Asus\TurboV\TurboV.exe C:\Program Files (x86)\PowerISO\PWRISOVM.EXE C:\Program Files (x86)\OpenOffice.org 3\program\soffice.exe C:\Program Files (x86)\OpenOffice.org 3\program\soffice.bin D:\Downloads\HijackThis.exe C:\Program Files (x86)\uTorrent\uTorrent.exe R1 - HKCU\Software\Microsoft\Internet Explorer\[...] [...] O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [HDAudDeck] C:\Program Files (x86)\VIA\VIAudioi\VDeck\VDeck.exe -r O4 - HKLM\..\Run: [StartCCC] "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun O4 - HKLM\..\Run: [TurboV] "C:\Program Files\Asus\TurboV\TurboV.exe" O4 - HKLM\..\Run: [PWRISOVM.EXE] C:\Program Files (x86)\PowerISO\PWRISOVM.EXE O4 - HKLM\..\Run: [googletalk] C:\Program Files (x86)\Google\Google Talk\googletalk.exe /autostart O4 - HKLM\..\Run: [AdobeCS4ServiceManager] "C:\Program Files (x86)\Common Files\Adobe\CS4ServiceManager\CS4ServiceManager.exe" -launchedbylogin O4 - HKCU\..\Run: [uTorrent] "C:\Program Files (x86)\uTorrent\uTorrent.exe" O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O4 - Startup: OpenOffice.org 3.1.lnk = C:\Program Files (x86)\OpenOffice.org 3\program\quickstart.exe O13 - Gopher Prefix: O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AMD External Events Utility - Unknown owner - C:\Windows\system32\atiesrxx.exe (file missing) O23 - Service: Asus System Control Service (AsSysCtrlService) - Unknown owner - C:\Program Files (x86)\Asus\AsSysCtrlService\1.00.02\AsSysCtrlService.exe O23 - Service: DeviceVM Meta Data Export Service (DvmMDES) - DeviceVM - C:\Asus.SYS\config\DVMExportService.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: ESET HTTP Server (EhttpSrv) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\EHttpSrv.exe O23 - Service: ESET Service (ekrn) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\x86\ekrn.exe O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: FLEXnet Licens

    Read the article

  • IIS running but not serving content

    - by Kyle
    I have an internal dev server running Windows 2k8 R2 with the Web and FTP Server roles set up which won't serve any content at all. Trying to connect from another host via telnet yields 'connection failed': c:\>telnet devserver 80 Connecting To devserver...Could not open connection to the host, on port 80: Conn ect failed Using netstat -an | find "80" on the dev server returns no connections on port 80 (a few on 1801, etc) tcpview confirms this, listing no open connections on port 80. The following services related to the Web role are running: World Wide Web Publishing Service Application Host Helper Service Microsoft FTP Service (ftp connections to port 21 are granted) Windows Process Activation Service The default website bindings are: Type Host Name Port IP Address Binding Information http 80 * net.tcp 808:* net.pipe * net.msmq localhost msmq.formatname localhost When setting up a new application under the default site, the test function passes both connection/authorisation only if the 'connect as' user is local admin, otherwise the test errors with 'invalid application path'. At no point is the W3SVC service PID bound to port 80 (it is running and bound to 21 for ftp). There are no W3SVC log directory at c:\inetpub\logs\LogFiles\ (only FTPSVC2), and no HTTPERR directory at c:\windows\system32\ or c:\windows\system32\logfiles\. There do not appear to be any related errors in the event logs. I'd really appreciate any thoughts on be a good place dig into what's (not) going on here!

    Read the article

  • How do I upgrade the BIOS to boot the motherboard when the CPU is not suported?

    - by Matt
    So I have a Tyan S8225 motherboard with a Valencia (Opteron 4200) CPU. Two of us have tried everything. We have even swapped the whole motherboard, Power supply, memory, even a different CPU (still Valencia). We even tried it without any memory installed and with only a single CPU. There are no beep codes as I suspect even those are controlled by the BIOS boot process. We put the whole thing on the bench with just the power supply, VGA, keyboard and network (for IPMI) connected. The IPMI is not even showing the BIOS starting, but the IPMI is working. After some hunting around, I discovered the claim on the website is that the Valencia CPU's are not supported on older BIOS revisions. For a start, I don't know what the bios revision is and if it's older but it's the only thing left. Could the BIOS be causing a board not to boot at all? If that's the case, then is there any other way to update the BIOS without buying an old CPU only to be put back in a box just to update the BIOS? Yes, we even tried updating the BIOS through IPMI but you can't do that either.

    Read the article

  • Server hang - data loss on reboot, post mortem analysis

    - by rovangju
    A development server I'm responsible for (ext3 on raid 5 w/Debian Squeeze) froze up over the weekend and I was forced to reset it, as in unresponsive from KVM/physical keyboard access, no eth devices responding, etc. Not even the backup process ran (Figures, the one time I don't check for confirmation) So after the reset, it turns out that every trace of disk IO activity that should have happened for a period of ~24H is completely gone. The log files have a big gap in the dates and times. As if the writes were never committed to disk, no processes seemed to have run. Luckily it was a weekend and nothing of value would have been lost and I don't suspect a hack. What can I do in post mortem to this event - to prevent it from ever happening again? I've seen this happen before on a completely different machine running FreeBSD. I am rounding up the disk checking tools right now - but there must be more going on! Mount options: /dev/sda1 on / type ext3 (rw,errors=remount-ro) Kernel: Linux dev 2.6.32-5-686-bigmem Disk/Inodes: 13%/3%

    Read the article

  • Lenovo Ideapad Y480 can't reinstall windows?

    - by elegantonyx
    Alright, so here's the deal... For a while, I wanted to mess with Linux. I don't know why, but I wanted to. So, what I did was use WUBI and install Ubuntu. Because of some unknown reason (Intel Rapid Start? Half the drivers being on a Lenovo-installed SSD [separate from the main hard drive]?) it wouldn't dual boot. So, I decided to use Linux Mint instead, and install it in a partition. Since Windows 7 Home Premium won't make partitions any more if you have a certain number already, I just shrank my system drive and left empty space for the installer to claim. When I installed Mint, it worked, but left my Windows 7 installation unable to boot and eventually it corrupted. I tried to use a system repair disc I burned earlier but it didn't find the Windows installation, so I assume the partition corrupted. I used this link:http://www.pcworld.com/article/248995/how_to_install_windows_7_without_the_disc.html to try and reinstall Windows. What happened was that originally it said that the partition I was trying to reinstall from had been locked down by the OEM (Lenovo). So, I went into GParted, wiped EVERYTHING, and selected 'Construct new Boot record' or whatever that function is, and now the error is: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information." Does anyone know how to see the log files? Can anyone help? This system is a month old but the warranty only covers hardware failures, and I would need to pay around USD$60 for them to fix it. Please help. Any ideas? this is my main machine... Extra information: I have at my disposal: System Repair Disc (Burned myself) Windows 7 Home Premium 64 bit SP1 installation disk (burned from the pcworld links) Gparted Live CD Linux Mint 13 live cd A system backup (from the morning before this catastrophe) made using the Windows Backup and Restore. I put it on an external drive...that should be safe for now.

    Read the article

  • Samba Share - MS Excel when saved (can't access the file, there are several possible reasons)

    - by brain90
    Dear Fellow ServerFaulter, I have a weird problem in my samba share. I have one share definition for 3 client (A,B,C) This share contain some excel file which having a lot of formula and linked each other. Client A access the file with libre office (ubuntu), client B access with WinXP & MS Office 2003, The write and read process working successfuly on Both of them. The problem occur when client C accessing the same file with MS Excel 2003 (windows xp). This messagebox appear when he saving the file : Microsoft office excel cannot access the \\192.168.1.23\myshare\ There are several possible reasons: - The File ort path does not exist The file is being used by another program. - The workbook you are trying to save has the same name as a - Currently open workbooks. I was trying http://support.microsoft.com/kb/291204 but it didnt work. Below is my share definition : [brainshare] comment = brainshare path = /opt/brainshare/ valid users = @brainshare force group = brainshare read only = No create mask = 0775 veto files = /*.scr/*.eml/thumbs.com/ Help me please... Thanks in advance ! Server: Ubuntu 10.10, Samba version 3.5.4

    Read the article

  • Linux Mint reset display resolution from console

    - by wullxz
    I have a Linux Mint 13 Xfce in a VMware Workstation 8 VM and set the resolution from 800x600 to 1280x768 and now I get permanently logged out when I try to login. I knew how to get back to my old resolution back in the xorg.conf days but Linux Mint now uses xrandr which won't display any displays when running # xrandr because X is not running (of course not - I can't login over GUI). I know that there are configuration files in /etc/X11/Xsession.d/ because I configured a debian based thinclient's resolution in a file called /etc/X11/Xsession.d/91configure_display but that file doesn't exist in my Linux Mint VM. So, how do I reset my X screen resolution from console? Edit: I forgot to tell you that I can't change resolution in console: # xrandr -s 800x600 Can't open display This message appears every time I use xrandr or xrandr -s *resolution* Update: I tried what bWowk suggested: # export DISPLAY=:0.0 # xrandr -s 800x600 No protocol specified No protocol specified Can't open display :0.0 So, that doesn't work either. Isn't there a configuration file that is executed every time X starts? X is running btw - ps aux | grep X shows one process /usr/bin/X running.

    Read the article

  • Apache2 return 404 for proxy requests before reaching WSGI

    - by Alejandro Mezcua
    I have a Django app running under Apache2 and mod_wsgi and, unfortunately, lots of requests trying to use the server as a proxy. The server is responding OK with 404 errors but the errors are generated by the Django (WSGI) app, which causes a high CPU usage. If I turn off the app and let Apache handle the response directly (send a 404), the CPU usage drops to almost 0 (mod_proxy is not enabled). Is there a way to configure Apache to respond directly to this kind of requests with an error before the request hits the WSGI app? I have seen that maybe mod_security would be an option, but I'd like to know if I can do it without it. EDIT. I'll explain it a bit more. In the logs I have lots of connections trying to use the server as a web proxy (e.g. connections like GET http://zzz.zzz/ HTTP/1.1 where zzz.zzz is an external domain, not mine). This requests are passed on to mod_wsgi which then return a 404 (as per my Django app). If I disable the app, as mod_proxy is disabled, Apache returns the error directly. What I'd finally like to do is prevent Apache from passing the request to the WSGI for invalid domains, that is, if the request is a proxy request, directly return the error and not execute the WSGI app. EDIT2. Here is the apache2 config, using VirtualHosts files in sites-enabled (i have removed email addresses and changed IPs to xxx, change the server alias to sample.sample.xxx). What I'd like is for Apache to reject any request that doesn't go to sample.sample.xxx with and error, that is, accept only relative requests to the server or fully qualified only to the actual ServerAlias. default: <VirtualHost *:80> ServerAdmin [email protected] ServerName X.X.X.X ServerAlias X.X.X.X DocumentRoot /var/www/default <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options FollowSymLinks AllowOverride None Order allow,deny allow from all </Directory> ErrorDocument 404 "404" ErrorDocument 403 "403" ErrorDocument 500 "500" ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> actual host: <VirtualHost *:80> ErrorDocument 404 "404" ErrorDocument 403 "403" ErrorDocument 500 "500" WSGIScriptAlias / /var/www/sample.sample.xxx/django.wsgi ServerAdmin [email protected] ServerAlias sample.sample.xxx ServerName sample.sample.xxx CustomLog /var/www/sample.sample.xxx/log/sample.sample.xxx-access.log combined Alias /robots.txt /var/www/sample.sample.xxx/static/robots.txt Alias /favicon.ico /var/www/sample.sample.xxx/static/favicon.ico AliasMatch ^/([^/]*\.css) /var/www/sample.sample.xxx/static/$1 Alias /static/ /var/www/sample.sample.xxx/static/ Alias /media/ /var/www/sample.sample.xxx/media/ <Directory /var/www/sample.sample.xxx/static/> Order deny,allow Allow from all </Directory> <Directory /var/www/sample.sample.xxx/media/> Order deny,allow Allow from all </Directory> </VirtualHost>

    Read the article

  • Domino to Exchange 2007 (or 2010) Design Concerns?

    - by NickToyota
    Today we got the executive green light to proceed with changing from a Domino platform to Exchange. The business prefers Exchange for a messaging platform. (even though IMO IBM Domino is fine - if it aint broke, don't fix it but it was not my call). I have been put in charge of Domino to Exchange process goes smoothly as possible. I have also been told to put together costs for this project. I have some questions and concerns re: network design, licensing, costs: The current setup is as follows. 1 HQ office (100 users), 1 secondary office (50 users), 5 branch offices (under 10 users). 5 different email domains Windows Server 2003 functional level with a few 2008 R2 Servers Lotus Domino Notes Servers (one in each office) Ironmail Appliance Public Domino Web Mail server Majority G5+ Proliant Servers Domino Blackberry Enterprise license and server No VoIP phones What are the basic hardware requirements for Exchange 2007 or 2010? Can I simply purchase a single physical server? Will each office require an Exchange server or possibly additional servers (roles)? How is email routed to the smaller branch offices? Standard or Enterprise licenses? The business has been running Domino (messaging and application services) for over 10 years and also want Exchange to support email services, Blackberry, Outlook Web Access, possibly support for iPhone devices. Thank you Serverfault universe.

    Read the article

  • AWS Application - Subscription Payments Scheduled but Not Initializing

    - by nicorellius
    I briefly browsed the AWS forums but these are not nearly as easy to use and efficient as Stack Exchange derived ones, so here I am... the company I work for has an app on the AWS cloud. In general the app works well. However, since it is new, we haven't had many customers and the ones who signed up are now coming to the point where their subscriptions to our service should be renewed. In comes my question. When I query the database for payment status of certain subscriptions using the console, I get what I would expect: Instrument XYZ is on a Monthly subscription (subscription=xxxyyyzz). The subscription is active with an expiration date of 19 Apr 2010 10:43 Z The payment token will expire on 1 Dec 2012 12:00 Z There are xy runs remaining. The subscription fee of $XX.xx will be charged on 17 Apr 2010 10:43 Z OK, this is great. According to this, I would expect the next payment to be initiated on 17 Apr. The reason I am asking is because for a different user last month I got this same output but the payment never went through, i.e., was not initiated through Amazon payments. The user didn't see the payment go through and neither did we. It should be noted that the initial payments were received. The sign up process works and if the user goes to "pay" from within our app, they will be directed to https://payments.amazon.com to make their payment. Any ideas?

    Read the article

  • SSSD Authentication

    - by user24089
    I just built a test server running OpenSuSE 12.1 and am trying to learn how configure sssd, but am not sure where to begin to look for why my config cannot allow me to authenticate. server:/etc/sssd # cat sssd.conf [sssd] config_file_version = 2 reconnection_retries = 3 sbus_timeout = 30 services = nss,pam domains = test.local [nss] filter_groups = root filter_users = root reconnection_retries = 3 [pam] reconnection_retries = 3 # Section created by YaST [domain/mose.cc] access_provider = ldap ldap_uri = ldap://server.test.local ldap_search_base = dc=test,dc=local ldap_schema = rfc2307bis id_provider = ldap ldap_user_uuid = entryuuid ldap_group_uuid = entryuuid ldap_id_use_start_tls = True enumerate = False cache_credentials = True chpass_provider = krb5 auth_provider = krb5 krb5_realm = TEST.LOCAL krb5_kdcip = server.test.local server:/etc # cat ldap.conf base dc=test,dc=local bind_policy soft pam_lookup_policy yes pam_password exop nss_initgroups_ignoreusers root,ldap nss_schema rfc2307bis nss_map_attribute uniqueMember member ssl start_tls uri ldap://server.test.local ldap_version 3 pam_filter objectClass=posixAccount server:/etc # cat nsswitch.conf passwd: compat sss group: files sss hosts: files dns networks: files dns services: files protocols: files rpc: files ethers: files netmasks: files netgroup: files publickey: files bootparams: files automount: files ldap aliases: files shadow: compat server:/etc # cat krb5.conf [libdefaults] default_realm = TEST.LOCAL clockskew = 300 [realms] TEST.LOCAL = { kdc = server.test.local admin_server = server.test.local database_module = ldap default_domain = test.local } [logging] kdc = FILE:/var/log/krb5/krb5kdc.log admin_server = FILE:/var/log/krb5/kadmind.log default = SYSLOG:NOTICE:DAEMON [dbmodules] ldap = { db_library = kldap ldap_kerberos_container_dn = cn=krbContainer,dc=test,dc=local ldap_kdc_dn = cn=Administrator,dc=test,dc=local ldap_kadmind_dn = cn=Administrator,dc=test,dc=local ldap_service_password_file = /etc/openldap/ldap-pw ldap_servers = ldaps://server.test.local } [domain_realm] .test.local = TEST.LOCAL [appdefaults] pam = { ticket_lifetime = 1d renew_lifetime = 1d forwardable = true proxiable = false minimum_uid = 1 clockskew = 300 external = sshd use_shmem = sshd } If I log onto the server as root I can su into an ldap user, however if I try to console locally or ssh remotely I am unable to authenticate. getent doesn't show the ldap entries for users, Im not sure if I need to look at LDAP, nsswitch, or what: server:~ # ssh localhost -l test Password: Password: Password: Permission denied (publickey,keyboard-interactive). server:~ # su test test@server:/etc> id uid=1000(test) gid=100(users) groups=100(users) server:~ # tail /var/log/messages Nov 24 09:36:44 server login[14508]: pam_sss(login:auth): system info: [Client not found in Kerberos database] Nov 24 09:36:44 server login[14508]: pam_sss(login:auth): authentication failure; logname=LOGIN uid=0 euid=0 tty=/dev/ttyS1 ruser= rhost= user=test Nov 24 09:36:44 server login[14508]: pam_sss(login:auth): received for user test: 4 (System error) Nov 24 09:36:44 server login[14508]: FAILED LOGIN SESSION FROM /dev/ttyS1 FOR test, System error server:~ # vi /etc/pam.d/common-auth auth required pam_env.so auth sufficient pam_unix2.so auth required pam_sss.so use_first_pass server:~ # vi /etc/pam.d/sshd auth requisite pam_nologin.so auth include common-auth account requisite pam_nologin.so account include common-account password include common-password session required pam_loginuid.so session include common-session session optional pam_lastlog.so silent noupdate showfailed

    Read the article

  • How do you install .net4 on a Server 2008 r2 machine through psremoting in powershell?

    - by Jake
    I need to write a script that installs .net 4 remotely using powershell to a group of Server 2008 R2 machines. I based my script off of http://social.technet.microsoft.com/Forums/en-US/winserverpowershell/thread/3045eb24-7739-4695-ae94-5aa7052119fd/. enter-pssession -computername localhost $arglist = "/q /norestart /log C:\Users\tempuser\Desktop\dotnetfx4" $filepath = "C:\Users\tempuser\Desktop\dotNetFx40_Full_setup.exe" Start-Process -FilePath $filepath -ArgumentList $arglist -Wait -PassThru After running the command I would get the following log errors (running the same lines locally would install .net without error): Action: Downloading Item Failed to CreateJob : hr= 0x80200014 Action: Performing actions on all Items Action: Performing Action on Exe at C:\Users\tempuser\Desktop\dotnetfx4\SetupUtility.exe Exe (C:\Users\tempuser\Desktop\dotnetfx4\SetupUtility.exe) succeeded. Exe Log File: dd_SetupUtility.txt Action complete Action: ServiceControl - Stop clr_optimization_v2.0.50727_32 ServiceControl operation succeeded! Action complete Action: ServiceControl - Stop clr_optimization_v2.0.50727_64 ServiceControl operation succeeded! Action complete Action: Performing Action on Exe at C:\Users\tempuser\AppData\Local\Temp\Microsoft .NET Framework 4 Setup_4.0.30319\Windows6.1-KB958488-v6001-x64.msu Exe (C:\Users\tempuser\AppData\Local\Temp\Microsoft .NET Framework 4 Setup_4.0.30319\Windows6.1-KB958488-v6001-x64.msu) failed with 0x5 - Access is denied. . PerformOperation on exe returned exit code 5 (translates to HRESULT = 0x5) Action complete OnFailureBehavior for this item is to Rollback. Action: Performing actions on all Items Action complete Action complete Action: Downloading http://go.microsoft.com/fwlink/?LinkId=164184&clcid=0x409 using WinHttp WinHttpDetectAutoProxyConfigUrl failed with error: 12180 Unable to retrieve Proxy information although WinHttpGetIEProxyConfigForCurrentUser called succeeded Action complete C:\Users\tempuser\AppData\Local\Temp\Microsoft .NET Framework 4 Setup_4.0.30319\TMPF279.tmp.exe: Verifying signature for netfx_Core.mzz C:\Users\tempuser\AppData\Local\Temp\Microsoft .NET Framework 4 Setup_4.0.30319\TMPF279.tmp.exe Signature verified successfully for netfx_Core.mzz Action complete Decompression completed with code: 16389 Decompression of payload failed: C:\Users\tempuser\AppData\Local\Temp\Microsoft .NET Framework 4 Setup_4.0.30319\netfx_Core.mzz Action complete Final Result: Installation failed with error code: (0x80074005) (Elapsed time: 0 00:00:28). Is there some security setting or perhaps something else I've missed?

    Read the article

  • How to deduplicate 40TB of data?

    - by Michael Stauffer
    I've inherited a research cluster with ~40TB of data across three filesystems. The data stretches back almost 15 years, and there are most likely a good amount of duplicates as researchers copy each others data for different reasons and then just hang on to the copies. I know about de-duping tools like fdupes and rmlint. I'm trying to find one that will work on such a large dataset. I don't care if it takes weeks (or maybe even months) to crawl all the data - I'll probably throttle it anyway to go easy on the filesystems. But I need to find a tool that's either somehow super efficient with RAM, or can store all the intermediary data it needs in files rather than RAM. I'm assuming that my RAM (64GB) will be exhausted if I crawl through all this data as one set. I'm experimenting with fdupes now on a 900GB tree. It's 25% of the way through and RAM usage has been slowly creeping up the whole time, now it's at 700MB. Or, is there a way to direct a process to use disk-mapped RAM so there's much more available and it doesn't use system RAM? I'm running CentOS 6.

    Read the article

  • WAMP starts Apache or Mysql, but not both?

    - by ladenedge
    When I install WAMP, the Apache and Mysql services are set to run as the LocalService user and all works well. However, because I need to access remote UNC paths in my PHP code, I need to run at least Apache as a user that exists on both the local host and the remote host - I'll call him WampUser. When both Apache and Mysql are set to start as WampUser, I cannot start both at the same time. If both are stopped, I can start either successfully. When I attempt to start the other, I get Error 1053: The service did not respond to the start or control request in a timely fashion. This error appears immediately - there is no timeout. When at least one of the services is set to start as LocalService, both start fine. I can, therefore, solve my problem by setting Apache to WampUser and Mysql to LocalService, but I'm more interested in why this is happening in the first place. I'm especially curious because this situation does not occur on other servers - something I've done to this server has made these two services exclusive when running as the same user. Here are some miscellaneous data points: I am using Windows Server 2003. I've provided recursive Full Control to the C:\wamp directory for WampUser. Nothing appears in the event log after the service fails. No log entries appear in either the Mysql log or the Apache error log. Neither application appears in the process list when the appropriate service is stopped. Any ideas?

    Read the article

  • Why is squid breaking kerberos/NTLM auth?

    - by DonEstefan
    I'm using squid 2.6.22 (Centos 5 Default) as a proxy. Squid seems to break the authentication process for web pages when they require NTLM or Kerberos Auth. I tested with sharepoint 2007 and tried all 3 authentication methods (NTLM, Kerberos, Basic). Accessing the site without squid works in all cases. When I access the same page with squid, then only basic-auth works. Using IE or Firefox desn't make any difference. Squid itself can be used by anybody (no auth_param configured). Its a bit tricky to find solutions online, since most of the topics whirl around auth_param for authenticating users to squid rather than authenticating users to a webpage behind squid. Could anyone help? Edit: Sorry, but my first test was totally screwed up. I tested against the wrong webservers (Memo to myself: always check assumptions before testing). Now I realized that the problem scenario is completely different. Kerberos work for IE Kerberos works for Firefox (after changing "network.negotiate-auth.trusted-uris" in about:config) NTLM works for IE NTLM does NOT work in Firefox (even after changing "network.automatic-ntlm-auth.trusted-uris" in about:config) By the way: The feature that provides NTLM-passthrough in squid is called "connection pinning" and the HTTP header "Proxy-support: Session-based-authentication""

    Read the article

  • Windows 8.1 Insufficient storage available to create shadow copy

    - by Bob.at.SBS
    [Note: After I entered the problem statement, I found this question, which is apparently the same problem. Maybe one of us will get a good answer...] I have used the "Windows 7 File Recovery" tool under Windows 8 to create system image backups to an external USB hard drive. I built a new Windows 8.1 machine, and I want to create my first system image backup of that machine to the same USB hard drive. The "Windows 7 File Recovery" tool is gone in Windows 8.1, but wbAdmin is alive and well: wbAdmin start backup -backupTarget:\\?\Volume{2a2b...994f} -allCritical -quiet fails with this text displayed: wbadmin 1.0 - Backup command-line tool (C) Copyright 2013 Microsoft Corporation. All rights reserved. Retrieving volume information... This will back up (EFI System Partition),(C:),Recovery (300.00 MB) to \?\Volume {2a2b1255-3a86-11e3-be86-b8ca3a83994f}. The backup operation to F: is starting. Creating a shadow copy of the volumes specified for backup... Summary of the backup operation: The backup operation stopped before completing. The backup operation stopped before completing. Detailed error: ERROR - A Volume Shadow Copy Service operation error has occurred: (0x8004231f) Insufficient storage available to create either the shadow copy storage file or other shadow copy data. The EFI System Partition is 100 MB The Recovery Partition is 300 MB The C partition is 1.72 TB, NTFS, 218 GB used, 1.51 TB free The destination drive is 1.81 TB, NTFS, 678 GB used, 1.15 TB free I've fiddled with vssadmin resize shadowstorage, with no change in the error. vssadmin list shadowstorage displays: Shadow Copy Storage association For volume: (C:)\?\Volume{37a0...263}\ Shadow Copy Storage volume: (C:)\?\Volume{37a0...263}\ Used Shadow Copy Storage space: 2.39 GB (0%) Allocated Shadow Copy Storage space: 2.81 GB (0%) Maximum Shadow Copy Storage space: 531 GB (30%) Shadow Copy Storage association For volume: (F:)\?\Volume{2a2...94f}\ Shadow Copy Storage volume: (F:)\?\Volume{2a2...94f}\ Used Shadow Copy Storage space: 334 GB (17%) Allocated Shadow Copy Storage space: 337 GB (18%) Maximum Shadow Copy Storage space: UNBOUNDED (922154758%) (Yeah, the "percent calculation" for UNBOUNDED is seriously bogus.) I've run SFC /verifyonly and it seems happy. I've verified that the new `Volume Shadow Copy" service starts when I start the backup operation. Any suggestions?

    Read the article

  • Outlook express 6 crashes after "synchonizing account"

    - by Ira Baxter
    [EDIT: Revised OE version to match reality] I use Outlook Express (OE) 6.00.3790.3959 to read newsgroups. I regularly scan through about 100 newsgroups. When I select a newsgroup, and then select "synchronize account", OE goes through the newsgroups visibly updating the unread message count. It gets apparantly to the end, and then comes back to check for Watched Conversations, of which I typically have a few scattered across the newsgroups. It invariably crashes with some kind of access fault. A dialog box pops up saying "Want to debug with "; I invariable say No, and the process goes away. I restart OE, select the newsgroup, and skip "Synchronize Account"; I am able to read news and everything seems just fine. This behavior has occurred since I set it up several months ago. Is the newsgroups database screwed up? Can I run something like CHKDSK or Outlooks PST repair to fix things up? Any suggestions as to what to do? The system is Windows XP 64 system installed in January 2008. I accept Windows Updates and install them on a regular basis. I use Outlook (not OE) for regular email an it behaves perfectly normally.

    Read the article

  • Why is Windows Update trying to install an update I don't need?

    - by Oliver Salzburg
    I have a Windows 7 system that currently has a single update pending: Windows Internet Explorer 9 for Windows 7 for x64-based Systems If I try to install the update, Windows Update will: Create a restore point Fail with the error: Code 9C48 Windows Update encountered an error. The event log for the event reads: Installation Failure: Windows failed to install the following update with error 0x80070643: Windows Internet Explorer 9 for Windows 7 for x64-based Systems. If you search the web for that error, there are many other people with the exact same issue. Sadly, I am unable to apply the proposed solutions to my case, because I just installed this system. There is nothing on it, except Windows 7. I installed the system and ran through the updates. I also did the exact same process with this machine several times over the past few days due to a long-term test we just started. I didn't have any problems with any Windows Update on the previous installation runs and I know I didn't do anything different this time because I followed the installation procedures instructions which are to be used during the test. How did this happen and how do I solve it? Further Investigation So, as I always like to do, I ran the update again while running Process Monitor and dug up further details. WindowsUpdate.log First of all, there is a Windows Update log file located at C:\Windows\WindowsUpdate.log which I didn't know about. But I fail to see any significant entry in it, maybe you're more lucky: 2012-04-10 22:46:58:017 956 728 AU AU received approval from Ux for 1 updates 2012-04-10 22:46:58:017 956 728 AU AU setting pending client directive to 'Progress Ux' 2012-04-10 22:46:58:095 956 728 AU BeginInteractiveInstall invoked for Download 2012-04-10 22:46:58:095 956 728 AU Auto-approving update for download, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, ForUx=1, IsOwnerUx=1, HasDeadline=0, IsMinor=0 2012-04-10 22:46:58:095 956 728 AU Auto-approved 1 update(s) for download (for Ux) 2012-04-10 22:46:58:110 956 728 AU UpdateDownloadProperties: 0 download(s) are still in progress. 2012-04-10 22:46:58:110 956 728 AU ############# 2012-04-10 22:46:58:110 956 728 AU ## START ## AU: Download updates 2012-04-10 22:46:58:110 956 728 AU ######### 2012-04-10 22:46:58:110 956 728 AU # Approved updates = 1 2012-04-10 22:46:58:110 956 728 AU AU initiated download, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, callId = {35DF928B-B428-4BAC-8C63-55295967EFBB} 2012-04-10 22:46:58:110 956 728 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:46:58:110 956 728 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:110 956 728 AU Currently showing Progress UX client - so not launching any other client 2012-04-10 22:46:58:110 956 bb8 DnldMgr ************* 2012-04-10 22:46:58:110 956 bb8 DnldMgr ** START ** DnldMgr: Downloading updates [CallerId = AutomaticUpdatesWuApp] 2012-04-10 22:46:58:110 956 bb8 DnldMgr ********* 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Call ID = {35DF928B-B428-4BAC-8C63-55295967EFBB} 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Priority = 3, Interactive = 1, Owner is system = 0, Explicit proxy = 0, Proxy session id = 1, ServiceId = {9482F4B4-E343-43B6-B170-9A65BC822C77} 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Updates to download = 1 2012-04-10 22:46:58:110 956 bb8 Agent * Title = Windows Internet Explorer 9 for Windows 7 for x64-based Systems 2012-04-10 22:46:58:110 956 bb8 Agent * UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100 2012-04-10 22:46:58:110 956 bb8 Agent * Bundles 1 updates: 2012-04-10 22:46:58:110 956 bb8 Agent * {6D9A90B7-FAF9-4A47-9EFE-A506264873B3}.100 2012-04-10 22:46:58:110 956 bb8 DnldMgr *********** DnldMgr: New download job [UpdateId = {6D9A90B7-FAF9-4A47-9EFE-A506264873B3}.100] *********** 2012-04-10 22:46:58:110 956 728 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:110 956 728 AU # Pending download calls = 1 2012-04-10 22:46:58:110 956 728 AU ## RESUMED ## AU: Download update [UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}, succeeded] 2012-04-10 22:46:58:313 956 bb8 Agent ** END ** Agent: Downloading updates [CallerId = AutomaticUpdatesWuApp] 2012-04-10 22:46:58:313 956 bb8 Agent ************* 2012-04-10 22:46:58:313 956 718 AU ######### 2012-04-10 22:46:58:313 956 718 AU ## END ## AU: Download updates 2012-04-10 22:46:58:313 956 718 AU ############# 2012-04-10 22:46:58:313 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:46:58:313 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:313 956 718 AU Currently showing Progress UX client - so not launching any other client 2012-04-10 22:46:58:313 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:313 956 aac AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:46:58:313 956 aac AU No featured updates available. 2012-04-10 22:47:00:107 956 aac AU BeginInteractiveInstall invoked for Install 2012-04-10 22:47:00:107 956 aac AU Auto-approving update for install, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, ForUx=1, IsOwnerUx=1, HasDeadline=0, IsMinor=0 2012-04-10 22:47:00:107 956 aac AU Auto-approved 1 update(s) for install (for Ux), installType=1 2012-04-10 22:47:00:107 956 aac AU ############# 2012-04-10 22:47:00:107 956 aac AU ## START ## AU: Install updates 2012-04-10 22:47:00:107 956 aac AU ######### 2012-04-10 22:47:00:107 956 aac AU # Initiating manual install 2012-04-10 22:47:00:107 956 aac AU # Approved updates = 1 2012-04-10 22:47:00:107 956 aac AU ## RESUMED ## AU: Installing update [UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}] 2012-04-10 22:47:13:773 2232 9fc Handler : WARNING: Exit code = 0x8024200B 2012-04-10 22:47:13:773 956 718 AU # WARNING: Install failed, error = 0x80070643 / 0x00009C48 2012-04-10 22:47:13:773 2232 9fc Handler ::::::::: 2012-04-10 22:47:13:773 2232 9fc Handler :: END :: Handler: Command Line Install 2012-04-10 22:47:13:773 2232 9fc Handler ::::::::::::: 2012-04-10 22:47:13:851 956 a7c Agent ********* 2012-04-10 22:47:13:851 956 a7c Agent ** END ** Agent: Installing updates [CallerId = AutomaticUpdates] 2012-04-10 22:47:13:851 956 718 AU Install call completed. 2012-04-10 22:47:13:851 956 a7c Agent ************* 2012-04-10 22:47:13:851 956 718 AU # WARNING: Install call completed, reboot required = No, error = 0x00000000 2012-04-10 22:47:13:851 956 718 AU ######### 2012-04-10 22:47:13:851 956 718 AU ## END ## AU: Installing updates [CallId = {FCFF2A5C-25AB-4FB9-AB2B-35C65CCA6A9F}] 2012-04-10 22:47:13:851 956 718 AU ############# 2012-04-10 22:47:13:851 956 718 AU Install complete for all calls, reboot NOT needed 2012-04-10 22:47:13:851 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:47:13:851 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:13:851 956 498 AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:47:13:851 956 498 AU No featured updates available. 2012-04-10 22:47:14:366 956 168 AU No featured updates notifications to show 2012-04-10 22:47:14:366 956 168 AU UpdateDownloadProperties: 0 download(s) are still in progress. 2012-04-10 22:47:14:366 956 168 AU Triggering Offline detection (non-interactive) 2012-04-10 22:47:14:366 956 168 AU AU setting pending client directive to 'Install Complete Ux' 2012-04-10 22:47:14:366 956 168 AU Changing existing AU client directive from 'Progress Ux' to 'Install Complete Ux', session id = 0x1 2012-04-10 22:47:14:366 956 168 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:14:366 956 b78 AU ############# 2012-04-10 22:47:14:366 956 b78 AU ## START ## AU: Search for updates 2012-04-10 22:47:14:366 956 b78 AU ######### 2012-04-10 22:47:14:366 956 b78 AU ## RESUMED ## AU: Search for updates [CallId = {0198DD3A-D7B0-48F5-A77D-795F8A1BDCE8}] 2012-04-10 22:47:16:097 956 718 AU # 1 updates detected 2012-04-10 22:47:16:097 956 718 AU ######### 2012-04-10 22:47:16:097 956 718 AU ## END ## AU: Search for updates [CallId = {0198DD3A-D7B0-48F5-A77D-795F8A1BDCE8}] 2012-04-10 22:47:16:097 956 718 AU ############# 2012-04-10 22:47:16:097 956 718 AU No featured updates notifications to show 2012-04-10 22:47:16:097 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:47:16:097 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:16:097 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:16:113 956 55c AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:47:16:113 956 55c AU No featured updates available. 2012-04-10 22:47:18:780 956 bb8 Report REPORT EVENT: {27479C66-E930-4F9C-AFF2-27EDD76DED8F} 2012-04-10 22:47:13:773+0200 1 182 101 {B33ACEC1-3265-4D01-9C37-AC0892E95ED9} 100 80070643 AutomaticUpdates Failure Content Install Installation Failure: Windows failed to install the following update with error 0x80070643: Windows Internet Explorer 9 for Windows 7 for x64-based Systems. 2012-04-10 22:47:18:780 956 bb8 Report CWERReporter::HandleEvents - WER report upload completed with status 0x8 2012-04-10 22:47:18:780 956 bb8 Report WER Report sent: 7.5.7601.17514 0x80070643 B33ACEC1-3265-4D01-9C37-AC0892E95ED9 Install 101 Unmanaged 2012-04-10 22:47:18:780 956 bb8 Report CWERReporter finishing event handling. (00000000) WU-IE9-Windows7-x64.exe The actual update that is executed is downloaded and stored at the following location: C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe Executing that file manually, results in the following error message: IE9_main.log The IE9 installer/updater also creates an own log file located at C:\Windows\IE9_main.log For the update session in question, the installer logged: 00:00.000: ==================================================================== 00:00.016: Started: 2012/04/10 (Y/M/D) 23:10:53.897 (local) 00:00.032: Time Format in this log: MM:ss.mmm (minutes:seconds.milliseconds) 00:00.063: Command line: "C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe" 00:00.078: INFO: Setup installer for Internet Explorer: 9.0.8112.16421 00:00.094: INFO: Previous version of Internet Explorer: 9.0.8112.16443 00:00.110: INFO: Checking if iexplore.exe's current version is between 9.0.6001.0... 00:00.125: INFO: ...and 9.1.0.0... 00:00.141: INFO: Maximum version on which to run IEAK branding is: 9.1.0.0... 00:00.156: ERROR: A newer version of Internet Explorer is already installed on the system. 00:00.188: ERROR: Internet Explorer version check failed. 01:03.789: INFO: Setup exit code: 0x00009C48 (40008) - A more recent version of Internet Explorer is installed. 01:03.820: INFO: Scheduling upload to IE SQM server: http://sqm.microsoft.com/sqm/ie/sqmserver.dll 01:03.852: INFO: SQM Upload returned 403 01:03.867: INFO: Cleaning up temporary files in: C:\Windows\TEMP\IE978E.tmp 01:03.883: INFO: Unable to remove directory C:\Windows\TEMP\IE978E.tmp, marking for deletion on reboot. 01:03.898: INFO: Released Internet Explorer Installer Mutex Which pretty much confirms what the error message says when executing the update manually; it's simply already installed or even obsolete because a newer version is installed. So, why does it try to keep installing the update? Possible solutions? Uninstalling Windows Internet Explorer 9 and manually installing the cached C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe will result in the same error after applying all pending updates. Applying the FixIt for the issue You receive “0x80070643” or “0x643” error codes when you try to install .NET Framework updates through Windows Update or Microsoft Updates will not resolve the issue. Applying the suggested solution for the issue Error message when you try to install updates by using the Windows Update or Microsoft Update Web site: "0x80070003" will not resolve the issue. Running the FixIt Automatically diagnose and fix common problems with Windows Update does report having resolved issues with Windows Update, but didn't resolve the issue. Running the FixIt for the issue How to troubleshoot Windows Update or Microsoft Update when you are repeatedly offered an update does not resolve the issue. Neither with normal nor with aggressive settings.

    Read the article

  • How to transfer files via infrared on Linux?

    - by arielnmz
    I know this is a way too old technology but I've got some files inside a very old cellphone that I need to transfer to a very old computer. So far my Infrared USB device works well, it's detected by the machine (lsusb output): Bus 002 Device 002: ID 0df7:0620 Mobile Action Technology, Inc. MA-620 Infrared Adapter I've tried to send the file over MMS and even email (it lacks bluetooth, not to mention USB). But this cellphones's firmware doesn't let me attach the files. The file was originally transfered via IrDA, and it only has an internal memory (a whole 2 million bytes! whoa!). I found a package called irda-utils, but it seems that there are only two executables: irdaping and irdadump. I think the dump utility might do the job (which as far as I can see it's kind of a version of tcpdump but for IrDA), but I don't even know how to process the received frames. Could this question may be what I'm looking for? EDIT While reading through the Linux Infrared HOWTO I found about the OpenObex project, which may be what I'm looking for...

    Read the article

  • Port translation in router causing some email to fail

    - by user22037
    We are in the process of setting up a spam filter (SAVASM). One change we are making is to push incoming email on port 25 through our spam filter/server but have users actually send their email on a different port. I am attempting to make this happen by using port address translation to send port 25 traffic to the SAVASM server IP. As a step in making this change I setup port translation without actually changing the IP addresses. The NAT rules for the email server went from one Static NAT rule with no port specified, to multiple Static NAT rules each with a port or group matching the Access Rules for that server (smtp, pop3, http, https, and some other custom ports). The problem we are running into is confusing. Some outgoing mail through this server is failing when the router has the multiple NAT rules with port translation settings. Email goes through fine FROM our email to our internal accounts and to Gmail. However email fails when FROM our client's email address TO our client's email or their personal Comcast. The only situation that worked for them was if they changed FROM to Comcast and then messages went through fine to both Comcast and the client's accounts. Switching back to regular Static NAT rule everything then worked for them. Does anyone have a clue as to what might be going on? We are on a Cisco ASA 5500 box.

    Read the article

  • Mysql server fails to start

    - by Nicolas Thery
    Googling since two hours, I require your assistance. I'm on a Debian virtual machine and I cloned it. The only change is the new IP adress it has. Mysql doesn't start any more: Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed! There is no process called mysql. All the mysql log files in /var/log are empty. here is my.cnf file : [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking bind-address = 127.0.0.1 key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M general_log_file = /var/log/mysql/mysql.log log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M [mysqld_safe] syslog Here is the result of ifconfig : eth0 Link encap:Ethernet HWaddr 00:0c:29:12:98:9a inet adr:192.168.1.138 Bcast:192.168.1.255 Masque:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:754 errors:0 dropped:0 overruns:0 frame:0 TX packets:106 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 RX bytes:101177 (98.8 KiB) TX bytes:17719 (17.3 KiB) lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:560 (560.0 B) TX bytes:560 (560.0 B) As requested, here is the result of : sudo -u mysql mysqld, here is the result : root@debian:/home/nicolas/Bureau# sudo -u mysql mysqld 121004 14:26:57 [Note] Plugin 'FEDERATED' is disabled. mysqld: Can't find file: './mysql/plugin.frm' (errno: 13) 121004 14:26:57 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 121004 14:26:57 InnoDB: Initializing buffer pool, size = 8.0M 121004 14:26:57 InnoDB: Completed initialization of buffer pool 121004 14:26:57 InnoDB: Started; log sequence number 0 70822697 121004 14:26:57 [Note] Recovering after a crash using /var/log/mysql/mysql-bin 121004 14:26:57 [Note] Starting crash recovery... 121004 14:26:57 [Note] Crash recovery finished. 121004 14:26:57 [ERROR] mysqld: Can't find file: './mysql/host.frm' (errno: 13) 121004 14:26:57 [ERROR] Fatal error: Can't open and lock privilege tables: Can't find file: './mysql/host.frm' (errno: 13)

    Read the article

  • What is preventing my computer from going idle?

    - by brianberns
    When I first boot my Windows 7 computer, it will go idle if I stop using it - first the screensaver comes on, then the computer goes to sleep after a certain amount of time. This is the expected behavior. However, after I've used the computer for awhile without rebooting (after about a day or so), I've noticed that it stops going idle - the screensaver won't come on, and the computer won't sleep, no matter how long it sits unused. I've confirmed that the idle timer is increasing as expected via GetLastInputInfo. However, it looks like something is interfering with the results from CallNtPowerInformation. Every 14 or 16 seconds, the TimeRemaining value jumps back up to its maximum value when I query SystemPowerInformation. I've used the SysInternals Process Monitor to detect any unusual events that might be happening to trigger this reset, but come up empty. Does anyone know exactly what are the possible causes of TimeRemaining resetting to its maximum value? I'm fairly sure that it's not my mouse, keyboard, or network sending spurious events, because I've disabled each one and the problem continues to occur. This would also reset the GetLastInputInfo timer, which is not happening. I'm looking for something that affects SystemPowerInformation TimeRemaining, but does not affect GetLastInputInfo. Thanks.

    Read the article

  • !! 0xc01a00d !! aka Vista won't boot

    - by Chris
    Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box. One of my users has an HP DV5-1235dx laptop running Windows Vista Professional x64. Last night, our WSUS server pushed out a few updates including "Security Update for Windows Vista for x64-based Systems (KB960859)". When we try to boot the laptop today, a black screen with white text comes up displaying: xxx/169894 (something) Where xxx increments rapidly and something is some dll or registry key. Eventually that stops and the screen displays !! 0xc01a00d !! 35566/169894 (\Registry\Machine\COMPONENTS\DerivedDat...) No other computers that received this update are displaying the same error. So far I've tried running CHKDSK off of HBCD. It repaired a thing or two, but the computer still doesn't boot. I tried repairing the Windows install from the Vista CD, but I get a black screen with white text displaying something along the lines of: 0 No Emulation System Type 00 1 No Emulation System Type 00 Select one of the above Booting in Last Known Good Configuration doesn't work. Booting in Safe Mode freezes at Loading Windows Files [snip] Loaded: \windows\system32\drivers\crcdisk.sys Please wait... My next step is trying to boot Safe Mode with Command Prompt and try to run rstrui.exe. While I do that, does anybody have any guidance? Edit: Booting into Safe Mode with Command Prompt will not work. See Booting in Safe Mode above. Edit 2: I managed to boot from the Vista DVD. I ran the system repair, and now I get a black screen with white text saying: !! 0xc0000034 !! 290/169894 (_0000000000000000.cdf-ms) Edit 3: I ran the system repair again, and it attempted to repair my hard drive. It failed. Problem Signature: Problem Event Name: Startup Repair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 4 Problem Signature 04: 196611 Problem Signature 05: CorruptVolume Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6002.2.2.0.256.1 Locale ID: 1033 Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box.

    Read the article

< Previous Page | 914 915 916 917 918 919 920 921 922 923 924 925  | Next Page >