Search Results

Search found 27606 results on 1105 pages for 'javascript disabled'.

Page 918/1105 | < Previous Page | 914 915 916 917 918 919 920 921 922 923 924 925  | Next Page >

• Disabling Laptop (PB TJ-75) faulty card reader Linux

  - by Gab

  My problem comes from that my laptop [PB TJ-75] has a faulty Alcor card reader. It’s 100% sure, the device is dead and unusable whatever the OS is. It cannot be disabled in BIOS [latest: Vendor: Phoenix Technologies LTD Version: V1.26 Release Date: 05/04/2010]. If I could take it apart from the main board easily, and if with that, the system would never look again for it, I’ll be very happy! Is it possible, has anyone ever tried this? Or maybe, replacing the BIOS with a more open one, which let you disable the card reader. Does this exists? Here's what I've tried to disable it so far. In Win7, I choose ‘disable’ in device manager and that’s ok. If not, the device keeps on appearing and disappearing and lot of resources are used. In Lubuntu 13.04, I got extra boot time, with the msg:'sdb, assuming drive cache, etc.’ I tried other distros (isos booted by grub). I can boot Puppy, Gparted, and Redobackup apparently without any problem. I cannot boot Debian, live or install + tried Crunchbang and Tails. I got a loop :’usb device, scsi n+1 blabla‘. I tried "nousb", no result, I have blacklisted EHCI, no result, then usb_storage module, better boot time in Lubuntu, with just the message "...data transfer failed", better shutdown time too. But, no way to use usb storage medias. In Debian, it ends with BusyBox prompt. Is it possible to just disable that Alcor card reader? Does it have a specific module? Is there a special kernel boot option that I missed? Does it have something to do with kernel recompiling, and if yes, how to do with isos? Programming a driver which says everything is ok (out of my comprehension for the moment)? Disabling device by vendor id? What is the best way?

  Read the article

• Error setting up Data Protection Manager 2010 Agents / Network "Unauthenticated" in network settings

  - by Bowsa

  I'm not sure if the two are connected but i suspect they are. Basically I'm tring to setup Data Protection Manager 2010 on a fresh install of Server 2008 R2 in a SBS 2003 domain. Everything went fine until trying to install agents across the network. Upon clicking add, i get the following error message: Unable to connect to the Active Directory Domain Services Database. Make sure that the DPM server is a member of a domain and that the controller is running. Also verify that there is network connectivity between the DPM server and the domain controller. ID: 7 As usual (worryingly) the MSDN support for 2010 products is nearly non existant, clicking the error ID simply gives a page not found error. So after 2 days of Googling and trying various fixes (DNS settings, adding permissions to AD objects, rejoining the domain and many more) I thought I'd ask here in the hope that someone out there may have had this issue before. Any help greatly appreciated! Some further info: Firewalls are disabled on the Server 2008, SBS, and client machines. Manually installing and adding the client in also fails, as the DPM server tries to contact the DC first. Edit: I tried creating a new protection group instead, and it gives a different error upon adding the machines: Following machines are not found in AD: COMPUTERNAME.COMPANYNAME.LOCAL Is there a certain directory structure it follows in AD?

  Read the article

• mysqld refusing connections from localhost

  - by Dennis Rardin

  My mail server (Ubuntu 10.04) uses mysql for virtual domains, virtual users. For some reason, mysqld has started refusing connections from localhost. I see these in the mail server log: Oct 6 00:31:14 apollo postfix/trivial-rewrite[16888]: fatal: proxy:mysql:/etc/postfix/mysql-virtual_domains.cf(0,lock|fold_fix): table lookup problem and: Oct 7 13:39:15 apollo postfix/proxymap[25839]: warning: connect to mysql server 127.0.0.1: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 I also get the following in auth.log: Oct 6 22:33:31 apollo mysqld[31775]: refused connect from 127.0.0.1 Telnet to the local port: root@apollo:/var/log/mysql# telnet localhost 3306 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. Connection closed by foreign host. root@apollo:/var/log/mysql# I am not sure why this started happening, but there was a disk failure in a RAID 1 pair a bit earlier that day. So it's possible I have a damaged config file or something. But mail was working for at least an hour after the drive event, so who knows for sure? phpmyadmin works fine, and the databases themselves look like they're intact. I think/believe that selinux and iptables are disabled and not running. So ... why is mysqld refusing connections from localhost? What should I check? What processes might cause this if a .conf file or possibly a binary was damaged? Which other log files might contain clues? I've enabled "general logging" in /etc/mysql/my.cnf, but I get no interesting or informative entries there. Thanks, m00tpoint

  Read the article

• FTP not listing directory NcFTP PASV

  - by Jacob Talbot

  I am attempting to setup Multicraft on my server, all is running smoothly however the FTP won't allow anyone to connect from a remote FTP client, where net2ftp will work smoothly from a remote location. I have included the transcript from my FTP client, Transmit below to give you an idea of what's going on. I have disabled iptables as well, and still no luck either way. Transmit 4.1.7 (x86_64) Session Transcript [Version 10.8.2 (Build 12C54)] (21/10/12 11:23 PM) LibNcFTP 3.2.3 (July 23, 2009) compiled for UNIX 220: Multicraft 1.7.1 FTP server Connected to ateam.bn-mc.net. Cmd: USER jacob.9 331: Username ok, send password. Cmd: PASS xxxxxxxx 230: Login successful Cmd: TYPE A 200: Type set to: ASCII. Logged in to ateam.bn-mc.net as jacob.9. Cmd: SYST 215: UNIX Type: L8 Cmd: FEAT 211: Features supported: EPRT EPSV MDTM MLSD MLST type*;perm*;size*;modify*;unique*;unix.mode;unix.uid;unix.gid; REST STREAM SIZE TVFS UTF8 End FEAT. Cmd: OPTS UTF8 ON 200: OK Cmd: PWD 257: "/" is the current directory. Cmd: PASV Could not read reply from control connection -- timed out. (SReadline 1)

  Read the article

• Postfix "loops back to myself" error on relay to another IP address on same machine

  - by Nic Wolff

  I'm trying to relay all mail for one domain "ourdomain.tld" from Postfix running on port 2525 of one interface to another SMTP server running on port 25 of another interface on the same machine. However, when a message is received for that domain, we're getting a "mail for loops back to myself" error. Below are netstat and postconf, the contents of our /etc/postfix/transport file, and the error that Postfix is logging. (The high bytes of each IP address are XXXed out.) Am I missing something obvious? Thanks - # netstat -ln -A inet Proto Recv-Q Send-Q Local Address Foreign Address State ... tcp 0 0 XXX.XXX.138.209:25 0.0.0.0:* LISTEN tcp 0 0 XXX.XXX.138.210:2525 0.0.0.0:* LISTEN # postconf -d | grep mail_version mail_version = 2.8.4 # postconf -n alias_maps = hash:/etc/aliases allow_mail_to_commands = alias,forward bounce_queue_lifetime = 0 command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 default_privs = nobody default_process_limit = 200 html_directory = no inet_interfaces = XXX.XXX.138.210 local_recipient_maps = local_transport = error:local mail delivery is disabled mail_owner = postfix mailbox_size_limit = 0 mailq_path = /usr/bin/mailq manpage_directory = /usr/local/man message_size_limit = 10240000 mydestination = mydomain = ourdomain.tld myhostname = ourdomain.tld mynetworks = XXX.XXX.119.0/24, XXX.XXX.138.0/24, XXX.XXX.136.128/25 myorigin = ourdomain.tld newaliases_path = /usr/bin/newaliases queue_directory = /var/spool/postfix readme_directory = /etc/postfix recipient_delimiter = + relay_domains = ourdomain.tld relay_recipient_maps = sample_directory = /etc/postfix sendmail_path = /usr/sbin/sendmail setgid_group = postdrop smtpd_authorized_verp_clients = $mynetworks smtpd_recipient_limit = 10000 transport_maps = hash:/etc/postfix/transport unknown_local_recipient_reject_code = 450 # cat /etc/postfix/transport ourdomain.tld relay:[XXX.XXX.138.209]:25 # tail -f /var/log/maillog ... Aug 2 23:58:36 va4 postfix/smtp[9846]: 9858A758404: to=<nicwolff@... >, relay=XXX.XXX.138.209[XXX.XXX.138.209]:25, delay=1.1, delays=0.08/0.01/1/0, dsn=5.4.6, status=bounced (mail for [XXX.XXX.138.209]:25 loops back to myself)

  Read the article

• Defrag starting when not scheduled. What is triggering the defrag

  - by leroyclark

  I have a fileserver that is starting a defrag around 2:00 PM everyday. This is killing performance as it runs for ours becuase this is a file server and has multiple drives. All scheduled tasks regarding defrag have been disabled. I have verified that it is accessing the data drives(using SysInternals tools). The reason I might have though otherwise was the event log has multiple entries regarding defragging a db file related to shadow copies. Oh yes these drives take shadow copy snapshots multiple times per day but the times of them don't coincide with the defrag task. There is nothing in the event logs regarding defrag except those noted above in relation to shadow copies. I'm out of ideas looking for what is starting these jobs. One possiblility is that the drives are not being defgramented, but being analyized to determine if they need to be defragmented. I manually ran an analysis and the cpu usage(by dfrgntfs.exe) seems to be similar to what I'm seeing everday while the defrag process is running. However I've found no setting that schedules this analysis.

  Read the article

• Excel 2007 - "The macro may not be available in this workbook" Error

  - by Psycho Bob

  We use an Excel sheet that has been protected to prevent modification of it from end users. All in all they are only able to edit certain tabs to add information that will then be used to generate information on other tabs using equations and such. On the tab with the equations, a button is present called "Prep for Internal Hard Copy Print." This button runs a macro that selects the information on the tab, unprotects it, then sends a print job to the user's default printer that contains the unprotected content. Normally this works like a champ. This time around, however, the macro is throwing the following error: Cannot run the macro "FILENAME.xlsx'!MacroName'. The macro may not be available in this workbook or all macros may be disabled. As far as I can tell, the macros are still present within the workbook. This sheet is normally a .xlsm though the user saved it with a different filename as a .xlsx. Also, the macros appear only as MacroName in the .xlsm file and not "FILENAME.xlsx'!MacroName' as it does in the .xlsx. Finally, when I open the .xlsm it asks if I want to enable the macro content while the .xlsx does not prompt for this. Can anyone tell me what's going on with this sheet or know of a way that I can get the macros working in the .xlsx without having to start over with a different sheet?

  Read the article

• Tri-head linux system with Xmonad: is it possible to have HW acceleration

  - by progo

  What means there exists to have three monitors, all controlled by Xmonad and have hardware 3D acceleration as well? I had the pleasure of using three monitors earlier this year, and while Xmonad and Xinerama handle three monitors easily, I had to throw in an extra display driver, and also let go of Nvidia's own TwinView (which is a hack on Xinerama). This left me with no HW acceleration and some flickering as double buffering wouldn't work with certain applications. However, the three monitors handle so beautifully that I had hard time coming back to two. I understand the easiest way to achieve HW-accelerated tri-head combo is to split into two Xorgs. I wouldn't be able to switch windows between the Xorgs, so I'm not really into this solution. What's more, having a cheap and old PCI card along with even slightly better PCIe seemed to slow things down. Even if I occasionally disabled the third monitor from Xorg configure, I couldn't get HW acceleration to work. Only after I physically disconnected the old PCI card, I could get the games back in business. Would a Matrox Dual/Tri-head2go and a powerful Nvidia GPU do the trick? I understand Xmonad can be configured to "believe" that a "single" (as Dualhead2Go will merge) 3360x1050 display is actually two different ones? So that Xmonad's Mod-w and Mod-e would work properly there.

  Read the article

• Why I cannot copy install.wim from Windows 7 ISO to USB (in linux env)

  - by fastreload

  I need to make a USB bootable disk of Windows 7 ISO. My USB is formatted to NTFS, ISO is not corrupt. I can copy install.wim elsewhere but I cannot copy it to USB. I even tried rsync. rsync error sources/install.wim rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: write failed on "/media/52E866F5450158A4/sources/install.wim": Input/output error (5) rsync error: error in file IO (code 11) at receiver.c(322) [receiver=3.0.8] Stat for windows.vim File: `X15-65732 (2)/sources/install.wim' Size: 2188587580 Blocks: 4274600 IO Block: 4096 regular file Device: 801h/2049d Inode: 671984 Links: 1 Access: (0664/-rw-rw-r--) Uid: ( 1000/ umur) Gid: ( 1000/ umur) Access: 2011-10-17 22:59:54.754619736 +0300 Modify: 2009-07-14 12:26:40.000000000 +0300 Change: 2011-10-17 22:55:47.327358410 +0300 fdisk -l Disk /dev/sdd: 8103 MB, 8103395328 bytes 196 heads, 32 sectors/track, 2523 cylinders, total 15826944 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdd1 * 32 15826943 7913456 7 HPFS/NTFS/exFAT hdparm -I /dev/sdd: SG_IO: bad/missing sense data, sb[]: 70 00 05 00 00 00 00 0a 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ATA device, with non-removable media Model Number: UF?F?A????U]r???U u??tF?f?`~ Serial Number: ?@??~| Firmware Revision: ????V? Media Serial Num: $I?vnladip raititnot baelErrrol aoidgn Media Manufacturer: o eparitgns syetmiM Standards: Used: unknown (minor revision code 0x0c75) Supported: 12 8 6 Likely used: 12 Configuration: Logical max current cylinders 17218 0 heads 0 0 sectors/track 128 0 -- Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 0 MBytes device size with M = 1000*1000: 0 MBytes cache/buffer size = unknown Capabilities: IORDY(may be)(cannot be disabled) Queue depth: 11 Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 0 Current = ? Recommended acoustic management value: 254, current value: 62 DMA: not supported PIO: unknown * reserved 69[0] * reserved 69[1] * reserved 69[3] * reserved 69[4] * reserved 69[7] Security: Master password revision code = 60253 not supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 71112min for SECURITY ERASE UNIT. 172min for ENHANCED SECURITY ERASE UNIT. Integrity word not set (found 0xaa55, expected 0x80a5)

  Read the article

• my X server doesn't load a module called "glx", but my video drivers seem to be installed

  - by rumtscho

  I just got a new, very wide monitor (2560x1440) and there is no sense maximizing my applications. So I installed Compiz Config Settings Manager and enabled Grid. Nothing happened, the shortcuts don't move application windows. Went to System - Preferences - Appearance, the Visual effects tab. It at "disabled". When I try to set them to "normal" or "extra", a message box appears telling me that it's searching for video drivers, then disappears, and I get an error message "Desktop effects could not be enabled". I opened Xorg.0.log, and had errors there: (EE) Failed to load /usr/lib/xorg/modules/extensions//libglx.so (II) UnloadModule: "glx" (EE) Failed to load module "glx" (loader failed, 7) (II) LoadModule: "extmod" Going to Administration - System - Hardware drivers, it said that there are no available and/or installed hardware drivers. But apt-get said that it cannot install nvidia-glx-185, as it is already installed. Googling my error message suggested that I install and run something called envyng. This let me install the nvidia drivers again, and now I can see in the Hardware Drivers window that they are installed and active. But the error message in Xorg.0.log remains, and I still cannot enable the Compiz effects or use Grid. Now, I don't have enough Linux experience to understand if this is a single cause-effect-chain of problems, or three independent ones, but I'd appreciate help for any of them. I am running Ubuntu 9.10, the video card is a GeForce 7600GS.

  Read the article

• Unable to use OpenGL or install nVidia driver on openSUSE 12.2

  - by djechelon

  I have an ASUS N76VZ laptop with 12.2 openSUSE and GeForce GT650M card. I found that KDE doesn't allow me to use OpenGL rendering. I tried to install nVidia's driver from script but once it writes the xorg.conf file I'm unable to boot desktop. I have the following errors in system log Oct 30 08:28:13 RAYNOR kdm[2727]: X server died during startup Oct 30 08:28:13 RAYNOR kdm[2727]: X server for display :0 cannot be started, session disabled I noticed that the /etc/X11/xorg.conf backup file was empty, so I renamed the new xorg.conf and left none: the desktop booted!!! How can I fix OpenGL rendering with or without driver installation? [Update]: Xorg.0.log says [ 1434.207] compiled for 4.0.2, module version = 1.0.0 [ 1434.207] Module class: X.Org Server Extension [ 1434.207] (II) NVIDIA GLX Module 304.60 Sun Oct 14 20:44:54 PDT 2012 [ 1434.207] (II) Loading extension GLX [ 1434.207] (II) LoadModule: "record" [ 1434.207] (II) Loading /usr/lib64/xorg/modules/extensions/librecord.so [ 1434.207] (II) Module record: vendor="X.Org Foundation" [ 1434.207] compiled for 1.12.3, module version = 1.13.0 [ 1434.207] Module class: X.Org Server Extension [ 1434.207] ABI class: X.Org Server Extension, version 6.0 [ 1434.207] (II) Loading extension RECORD [ 1434.207] (II) LoadModule: "dri" [ 1434.207] (II) Loading /usr/lib64/xorg/modules/extensions/libdri.so [ 1434.207] (II) Module dri: vendor="X.Org Foundation" [ 1434.207] compiled for 1.12.3, module version = 1.0.0 [ 1434.207] ABI class: X.Org Server Extension, version 6.0 [ 1434.207] (II) Loading extension XFree86-DRI [ 1434.207] (II) LoadModule: "nvidia" [ 1434.208] (II) Loading /usr/lib64/xorg/modules/drivers/nvidia_drv.so [ 1434.208] (II) Module nvidia: vendor="NVIDIA Corporation" [ 1434.208] compiled for 4.0.2, module version = 1.0.0 [ 1434.208] Module class: X.Org Video Driver [ 1434.208] (II) NVIDIA dlloader X Driver 304.60 Sun Oct 14 20:24:42 PDT 2012 [ 1434.208] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs [ 1434.208] (++) using VT number 8 [ 1434.320] (EE) No devices detected. [ 1434.320] Fatal server error: [ 1434.320] no screens found [ 1434.320] Please consult the The X.Org Foundation support at http://wiki.x.org for help.

  Read the article

• Can any postfix guru assist me determine how emails are still being sent via my server from unauthorized sources?

  - by Dave

  Hi all, I'm getting a little concerned as I run a small server hosting a number of websites and manage the email for a few dozen people. Just recently though I've had a couple of notifications from spamcop alerting me that spam has been sent from my server, and when I have a look over the logs from time to time I can indeed see that there are many repeated attempts of mail being sent from my server. Most of the time it gets knocked back from the destination servers but sometimes its getting through. Unfortunately I'm not linux or postfix expert, I can get by but had though I had my machine locked down quite securely, I don't allow relaying, when I check the online DNS/MX tools they tend to report my server as being OK so I'm not sure where to take it now and hoping someone might be able to throw me a few pointers. I get lots of entries like this in my MAIL.INFO log Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 66B88257C12F: from=<>, size=3116, nrcpt=1 (queue active) Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 614C2257C1BC: from=<[email protected]>, size=2490, nrcpt=3 (queue active) and Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6471]: 0A316257C204: to=<[email protected]>, relay=none, delay=384387, delays=384384/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6470]: 5848C257C20D: to=<[email protected]>, relay=none, delay=384373, delays=384370/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) then there tends to be connection timeouts, so from what I see even though I had relaying disabled.. something is getting by and trying to send.. So if you can help that will be greatly appreciated, and any further logging/config info I can supply. Thanks

  Read the article

• Turn off gzip for a location in Nginx

  - by Nyxynyx

  How can gzip be turned off for a particular location and all its sub-directories? My main site is at http://mydomain.com and I want to turn gzip off for both http://mydomain.com/foo and http://mydomain.com/foo/bar. gzip is turned on in nginx.conf. I tried turning off gzip as shown below, but the Response Headers in Chrome's dev tools shows that Content-Encoding:gzip. How should gzip/output buffering be disabled properly? Attempt: server { listen 80; server_name www.mydomain.com mydomain.com; access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; root /var/www/mydomain/public; index index.php index.html; location / { gzip on; try_files $uri $uri/ /index.php?$args ; } location ~ \.php$ { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; fastcgi_read_timeout 300; } location /foo/ { gzip off; try_files $uri $uri/ /index.php?$args ; } }

  Read the article

• 530 5.7.1 Client was not authenticated Exchange 2010 for some computers within mask

  - by user1636309

  We have a classic problem with Client not Authenticated but with a specific twist: We have an Exchange 2010 cluster, let's say EX01 and EX02, the connection is always to smtp.acme.com, then it is switched through load balancer. We have an application server, call it APP01 There are clients connected to the APP01. There is a need for anonymous mail relay from both clients and APP01. The Anonymous Users setting of the Exchange is DISABLED, but the specific computers - APP01 and clients by the mask, let's say, 192.168.2.* - are enabled. For internal relay, a "Send Connector" is created, and then the above IP addresses are added for the connector to allow computers, servers, or any other device such as a copy machine to use the exchange server to relay email to recipients. The problem is that the relay works for APP01 and some clients, but not others (we get "Client not Authenticated") - all inside the same network and the same mask. This is basically what we do to test it outside of our application: http://smtp25.blogspot.sk/2009/04/530-571-client-was-not-authenticated.html So, I am looking for ideas: What can be the reason for such a strange behaviour? Where I can see the trace of what's going on at the Exchange side?

  Read the article

• Remote SQL server connection failure

  - by Sevki

  I am trying to connect to my MSSQL server 2008 web instance and im failing horribly... i get the error 26 and before you jump on me i have done these Check the spelling of the SQL Server instance name that is specified in the connection string. Use the SQL Server Surface Area Configuration tool to enable SQL Server to accept remote connections over the TCP or named pipes protocols. For more information about the SQL Server Surface Area Configuration Tool, see Surface Area Configuration for Services and Connections. Make sure that you have configured the firewall on the server instance of SQL Server to open ports for SQL Server and the SQL Server Browser port (UDP 1434). Make sure that the SQL Server Browser service is started on the server. in addition to theese i have disabled the firewall completely and tried other ports nothing works the same credentials work on the server but not on the client. this is the exact error message A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (.Net SqlClient Data Provider) Can anybody help?

  Read the article

• Ubuntu 12.04 suddenly cannot connect to WPA2/WPA Personal protected connection. Windows 7 can

  - by d4ryl3

  I have a laptop with Windows 7 and Ubuntu 12.04. I have a Cisco E1200 and when I set it up, it created 2 SSIDs. Let's name them: MyConnection (WPA/WPA2 personal), and MyConnection-Guest (no authentication, guest password entered via web browser). I had no problem connecting to MyConnection before, either in Windows 7 and Ubuntu. But now, I can't access MyConnection on Ubuntu. It just says "connecting..." then disconnects after a while. But I'm able to access the internet (on Ubuntu) when I connect to MyConnection-Guest. MAC filtering is off (even if it's on its MAC address is in the white list). Any idea why I'm unable to connect to MyConnection in Ubuntu? Thanks. Update: My Ubuntu installation can connect to ANY WiFi connection (WPA/WEP/no auth), except for MyConnection. Update2: This is what "The not so easy way" returned: Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A' Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf' Reading configuration file '/etc/wpa_supplicant.conf' Priority group 0 id=0 ssid='MyConnection' id=1 ssid='MyConnection' id=2 ssid='MyConnection' id=3 ssid='MyConnection' WEXT: cfg80211-based driver detected SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf capabilities: key_mgmt 0xf enc 0xf flags 0x0 netlink: Operstate: linkmode=1, operstate=5 Own MAC address: xx:xx:xx:xx:xx:xx wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0 ioctl[SIOCSIWENCODEEXT]: Invalid argument Driver did not support SIOCSIWENCODEEXT wpa_driver_wext_set_countermeasures RSN: flushing PMKID list in the driver Setting scan request: 0 sec 100000 usec WPS: UUID based on MAC address - hexdump(len=16): 16 3b d8 47 9e 24 50 89 96 16 6d 66 35 f3 58 37 EAPOL: SUPP_PAE entering state DISCONNECTED EAPOL: Supplicant port status: Unauthorized EAPOL: KEY_RX entering state NO_KEY_RECEIVE EAPOL: SUPP_BE entering state INITIALIZE EAP: EAP entering state DISABLED EAPOL: Supplicant port status: Unauthorized EAPOL: Supplicant port status: Unauthorized Added interface eth1

  Read the article

• Coming from Win XP to 7 and having new accessibility software problems

  - by Anonymous Jones

  I just switched from Windows XP Pro SP3 (32bit) to Windows 7 Ultimate (32bit) on a new PC. Now, both the new onscreen keyboard and a utility for sending mouse clicks are being problematic. The problem with 7's OSK is that some things I type only work intermittently or just dodgily. Like Alt+Tab with multiple Tabs, other Alt/Ctrl/Shift/Win key combinations, and the context menu key. Sometimes apps will not take focus for input at all. I use the OSK it in 'hover' mode, on 0,5 seconds. The clicking tool is Point-N-Click, which sends clicks when I dwell anywhere for 1.25 seconds with the mouse pointer. http://www.polital.com/pnc/ The problem with it is that sometimes it fails to click. Most often this happens in some of the control panel sections, on the taskbar, and when UAC pops up. It seems to occur in conjunction with OSK usage a bit too, I think. I'm using an Administrator account. DEP and UAC settings are default. What can I do to fix or work around either of these problems? I'm disabled so this really is killing usability.

  Read the article

• Exchange 2013 attachments too big?

  - by KPS

  I am having the toughest time sending large attachments, everywhere I have checked my file size limit for send/receive is 100mb but yet users are unable to receive files even at the size of 14mb. I'm using a spam filter (Appriver) and have worked with there support for a very long time, we see the following errors in logs 13:32:40.260 4 SMTP-000036([myserverIP]) rsp: 354 Start mail input; end with <CRLF>.<CRLF> 13:33:41.038 3 SMTP-000033([myserverIP]) write failed. Error Code=connection reset by peer 13:33:41.038 3 SMTP-000033([myserverIP]) [659500] failed to send. Error Code=connection reset by peer 13:33:41.038 4 SMTP([myserverIP]) [659500] batch reenqueued into tail Windows firewall is disabled on the exchange server, all other emails that are of smaller value come through just fine. Here is a print out of size limits: ConnectorType ConnectorName MaxReceiveMessageSize MaxSendMessageSize ------------- ------------- --------------------- ------------------ Send InternetSendConnector - 35 MB (36,700,160 bytes) Send Appriver-Smarthost - 35 MB (36,700,160 bytes) Receive Default EXCHSRVR 100 MB (104,857,600 bytes) - Receive Client Proxy EXCHSRVR 100 MB (104,857,600 bytes) - Receive Default Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive Outbound Proxy Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive Client Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive ExchangeRelay 100 MB (104,857,600 bytes) - TransportConfig - 100 MB (104,857,600 bytes) 10 MB (10,485,760 bytes) ADSiteLink DEFAULTIPSITELINK Unlimited Unlimited There is a no anti-virus on the server either that could be interfering, I am out of ideas at this point :( EDIT 1 After running BPA, it gives and error: Exchange Organization: Check whether the incoming message(CN=MyDomain,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=WG,DC=local) size isn't set The maximum incoming message size isn't set in organization 'CN=MyDomain,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=WG,DC=local'. This can cause reliability problems. Here are the sizes as of now: [PS] C:\Temp>Get-TransportConfig | ft MaxSendSize, MaxReceiveSize MaxSendSize MaxReceiveSize ----------- -------------- Unlimited Unlimited [PS] C:\Temp>Get-ReceiveConnector | ft name, MaxMessageSize Name MaxMessageSize ---- -------------- Default EXCHSRVR 100 MB (104,857,600 bytes) Client Proxy EXCHSRVR 100 MB (104,857,600 bytes) Default Frontend EXCHSRVR 100 MB (104,857,600 bytes) Outbound Proxy Frontend EXCHSRVR 100 MB (104,857,600 bytes) Client Frontend EXCHSRVR 100 MB (104,857,600 bytes) ExchangeRelay 100 MB (104,857,600 bytes) Again, smaller emails come through just fine. Seems like there is a 10mb receive limit somewhere that I cannot find.

  Read the article

• Installing Apache MPM Worker on Centos 5.5

  - by mrmartinblue

  I have a CentOS 5.5. server and am trying to switch from MPM Prefork to MPM worker. I have the standard yum httpd packages installed currently and from my reading I did the following: Uncomment the httpd.worker line in the /etc/sysconfig/httpd file. I also made sure that the httpd.worker file exists in the /usr/sbin/ directory. I also made sure that httpd service is stopped before making the above change. Ensured PHP was disabled for Apache. I'm fine with this and will use FastCGI to handle PHP files once I get the MPM worker up and running. Restart the httpd service, everything starts fine. Do a # httpd -V The console tells me it's still using prefork. If I do a # vi /etc/init.d/httpd the httpd.worker line is still commented out. I've tried changed this as well to no difference. Any suggestions? Things to look at? My application requires the worker MPM so the only choice I can think of is to go with ubuntu or another flavor that has the dedicated apache2-mpm-worker package. Is there something similar in the yum repos somewhere? Thanks in advance!

  Read the article

• How to install rmagick on Ubuntu 10.04?

  - by Andrew

  Here's what I've done so far: sudo apt-get install imagemagick libmagickcore-dev This did not throw any errors, so I think that ImageMagick is installed fine. Then I tried installing the gem: sudo gem install rmagick This resulted in the following error: ERROR: Error installing rmagick: ERROR: Failed to build gem native extension. /usr/bin/ruby1.8 extconf.rb checking for Ruby version >= 1.8.5... yes checking for gcc... yes checking for Magick-config... yes checking for ImageMagick version >= 6.4.9... yes checking for HDRI disabled version of ImageMagick... yes checking for stdint.h... yes checking for sys/types.h... yes checking for wand/MagickWand.h... no Can't install RMagick 2.13.1. Can't find MagickWand.h. *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby1.8 Gem files will remain installed in /usr/lib/ruby/gems/1.8/gems/rmagick-2.13.1 for inspection. Results logged to /usr/lib/ruby/gems/1.8/gems/rmagick-2.13.1/ext/RMagick/gem_make.out What do I need to do to install rmagick on Ubuntu 10.04?

  Read the article

• Simple Linux program that takes any HTTP/HTTPS request and returns a single page?

  - by ultrasawblade

  I have a Linux box operating as router. There's a NIC that's connected to the internet (WAN), a NIC connected to an 8-port GbE switch (LAN), and a NIC connected to a Linksys wireless N-router (WLAN). Routing between everything is working perfectly. I have security completely disabled on the wireless router, but the WLAN NIC is firewalled such that it will only accept DNS queries and PPTP VPN connections. Currently HTTP/HTTPS traffic and everything else is blocked. I would like to run something that listens on port 80/443 of the WLAN NIC, and, for non VPN'ed connections, given any HTTP/HTTPS request it will return a single webpage saying "Unauthenticated" and explain how to sign into the VPN. A transparent proxy seems to be what I need, but my searches all seem to direct me to Squid, which is already running on my server and seems overkill for this simple task. Is there a simpler, lightweight program out there that does just this or should I just suck it up and run two instances of Squid (or figure out how to configure it)? Or, is this entire VPN thing I'm doing complete nonsense and I should just enable encryption on the wireless router?

  Read the article

• Why won't my computer go to sleep automatically?

  - by Django Reinhardt

  Windows 8 is set to sleep after 30 mins, and it used to work, but recently it's started refusing to sleep. (I can still manually ask it to go to sleep without any issue.) I was having issues a while ago, but it was with my network adapter. That's since been disabled, so it's definitely not that: I've checked to see what devices are able to wake up my machine, but it only appears to be my mouse: Which is odd, because I haven't recently changed my mouse, and more confusing still: The monitor does go to sleep just fine. If it was actually the mouse keeping my system awake, I'm pretty sure the monitor wouldn't go to sleep. I've checked my Wake Timers, and nothing: I've also checked my existing requests... UPDATE: I found something. What to do with it, I don't know... Note: Even when /requests says that there's "NONE" under every category, my machine still won't sleep(!). In short: How can I tell what's preventing my computer from Sleeping? UPDATE: Ok, so I now have a few more pieces of the puzzle. I came back to my computer and it was ASLEEP! Lawks! It seems that the only times it doesn't sleep is if VLC Player is open, even if a video isn't actually playing. UPDATE UPDATE: Ok, so it won't sleep sometimes when VLC Player ISN'T running, either. Bah!

  Read the article

• How can I connect my Xbox to my Mac on my network

  - by codecowboy

  I have a wireless router/modem (Router 1) in my living room. This is connected to the internet (cable). Wireless is disabled as the router has a terrible wireless range. My Xbox is connected via ethernet to Router 1. Another LAN output from Router 1 connects to a powerline adapter. Router 1 acts as a DHCP server on 192.168.0.x and has the IP 192.168.0.1 In a second room I have Router 2. This has the powerline feed from Router 1 going into the WAN socket. This router runs the Tomato Firmware and acts as a wireless router for the rest of the house using the IP range 192.168.1.x. Router 2 IP is 192.168.1.1. My Mac is connected to Router 2 using a LAN cable and has the IP 192.168.0.133. Several mobile devices need wireless access. I want an ethernet connection to my Mac, not wireless. I should be able to use software like Connect360 to share media from my Mac to the XBox but the XBox does not see my Mac. I can ping 192.168.0.1 from the Mac. Is this possible using my current setup? If so, how?

  Read the article

• Connecting remotely to an SQL server inside a LAN

  - by vondip

  Hello everyone, I am using SQL server 2008 inside my home lan. I've configured it to accept remote connections and I can now connect to the server from other pcs inside the lan. The problems rises when I try connecting to the server from a computer outside of my home lan. I've disabled my router's firewall and I've configured a virtual server on port 1433 forwarding to the correct lan ip. What's wrong? why is it not working? Thank you very much for your help~! Edit: This is the error I keep getting: A network related or instance specific error occured while establishing connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that the SQL SERVER is configued to allow remote connections. (provider : Sql network interfaces, error: 25- Connection string is not valid) OK these are my router's details: edimax br-6204wg I am not sure how I am supposed to browse google.com. can you be a bit more specific?

  Read the article

• Help setting up an secondary authoritative DNS server.

  - by GLB03

  We have three Authoritative DNS servers and three recursive/caching DNS servers on my campus. Authoritative servers DNS1- Windows 2003 DNS2- Old Red Hat ----- Replacing w/ newer version DNS3- Windows 2008 (I installed) Caching and Recursive resolvers servers Server1- Windows 2003 Server2- CentOS 5.2 (I installed) Server3- CentOS 5.3 (I installed) I am replacing DNS2 with a newer Red Hat version, but have no documentation on how it was implemented. I have setup caching and windows authoritative servers, but not a linux secondary authoritative server. I have a perl script from the original server that pulls data from our DNS1 server. We use DJBDNS and TinyDNS on our linux servers. Our Network Engineer says the DNS2 server I am replacing is an authoritative server that doesn't need to be caching, but the only instructions I see is for an Authoritative server that does caching as well. Can someone point me in the right directions. I thought I was on the right track with using these instructions but when I query my new dns server I get "No response from server", I have temporarily disabled iptables to eliminate it from being an issue. ps -aux | grep dns avahi 3493 0.0 0.2 2600 1272 ? Ss Apr24 0:05 avahi-daemon: running [newdns2.local] root 5254 0.0 0.1 3920 680 pts/0 R+ 09:56 0:00 grep dns root 6451 0.0 0.0 1528 308 ? S Apr29 0:00 supervise tinydns dnslog 6454 0.0 0.0 1540 308 ? S Apr29 0:00 multilog t ./main tinydns 9269 0.0 0.0 1652 308 ? S Apr29 0:00 /usr/local/bin/tinydns

  Read the article

< Previous Page | 914 915 916 917 918 919 920 921 922 923 924 925  | Next Page >