Search Results

Search found 62161 results on 2487 pages for 'set difference'.

Page 943/2487 | < Previous Page | 939 940 941 942 943 944 945 946 947 948 949 950  | Next Page >

• PC can't detect second RAM installed

  - by kulwinder

  I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

  Read the article

• Traffic shaping on Linux with HTB: weird results

  - by DADGAD

  I'm trying to have some simple bandwidth throttling set up on a Linux server and I'm running into what seems to be very weird stuff despite a seemingly trivial config. I want to shape traffic coming to a specific client IP (10.41.240.240) to a hard maximum of 75Kbit/s. Here's how I set up the shaping: # tc qdisc add dev eth1 root handle 1: htb default 1 r2q 1 # tc class add dev eth1 parent 1: classid 1:1 htb rate 75Kbit # tc class add dev eth1 parent 1:1 classid 1:10 htb rate 75kbit # tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match ip dst 10.41.240.240 flowid 1:10 To test, I start a file download over HTTP from the said client machine and measure the resulting speed by looking at Kb/s in Firefox. Now, the behaviour is rather puzzling: the DL starts at about 10Kbyte/s and proceeds to pick up speed until it stabilizes at about 75Kbytes/s (Kilobytes, not Kilobits as configured!). Then, If I start several parallel downloads of that very same file, each download stabilizes at about 45Kbytes/s; the combined speed of those downloads thus greatly exceeds the configured maximum. Here's what I get when probing tc for debug info [root@kup-gw-02 /]# tc -s qdisc show dev eth1 qdisc htb 1: r2q 1 default 1 direct_packets_stat 1 Sent 17475717 bytes 1334 pkt (dropped 0, overlimits 2782 requeues 0) rate 0bit 0pps backlog 0b 12p requeues 0 [root@kup-gw-02 /]# tc -s class show dev eth1 class htb 1:1 root rate 75000bit ceil 75000bit burst 1608b cburst 1608b Sent 14369397 bytes 1124 pkt (dropped 0, overlimits 0 requeues 0) rate 577896bit 5pps backlog 0b 0p requeues 0 lended: 1 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 class htb 1:10 parent 1:1 prio 0 **rate 75000bit ceil 75000bit** burst 1608b cburst 1608b Sent 14529077 bytes 1134 pkt (dropped 0, overlimits 0 requeues 0) **rate 589888bit** 5pps backlog 0b 11p requeues 0 lended: 1123 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 What I can't for the life of me understand is this: how come I get a "rate 589888bit 5pps" with a config of "rate 75000bit ceil 75000bit"? Why does the effective rate get so much higher than the configured rate? What am I doing wrong? Why is it behaving the way it is? Please help, I'm stumped. Thanks guys.

  Read the article

• Installing Apache MPM Worker on Centos 5.5

  - by mrmartinblue

  I have a CentOS 5.5. server and am trying to switch from MPM Prefork to MPM worker. I have the standard yum httpd packages installed currently and from my reading I did the following: Uncomment the httpd.worker line in the /etc/sysconfig/httpd file. I also made sure that the httpd.worker file exists in the /usr/sbin/ directory. I also made sure that httpd service is stopped before making the above change. Ensured PHP was disabled for Apache. I'm fine with this and will use FastCGI to handle PHP files once I get the MPM worker up and running. Restart the httpd service, everything starts fine. Do a # httpd -V The console tells me it's still using prefork. If I do a # vi /etc/init.d/httpd the httpd.worker line is still commented out. I've tried changed this as well to no difference. Any suggestions? Things to look at? My application requires the worker MPM so the only choice I can think of is to go with ubuntu or another flavor that has the dedicated apache2-mpm-worker package. Is there something similar in the yum repos somewhere? Thanks in advance!

  Read the article

• Windows 7 Not Recognizing Camera Nor iPhone as Camera

  - by taudep

  I've been struggling with this one for a few days. I've recently upgraded an older computer to Windows 7 Home Premium. Neither my digital camera (A Canon SD1200IS) nor iPhone are ever detected as cameras, nor ever show up as accessable in Explorer. With the Canon camera, no driver is required. It's supposed to work with the default Windows 7 drivers. However, in the Control Panel's Device Manager, I'm always seeing a yellow icon next to the "Canon Digital Camera" device. I've uninstalled the device and let Windows attempt to reinstall, but it can never find a driver to install. With the iPhone, it's very similar. One big difference, though, is that iTunes can see the iPhone and back it up, etc. However, again when I go to the Device Manager, there's a yellow icon next to the iPhone. I've uninstalled iTunes, reinstalled, rebooted, deleted drivers, and let Window try to reinstall the driver, but it can never find the driver. So there seems to be some correlation that my machine can't detect cameras properly, and that it might be even a lower-level type of driver I'm struggling with. I know that USB however, does work, because I have have an external drive hooked into the machine. I've gone through the web and tried two hours worth of fixes, without success. I feel like if I can get the Canon camera detected, then the iPhone will be on it's way to being fixed too. BTW, I couldn't really find anything of use in the Event viewer. Any and all suggestions welcome.

  Read the article

• How can I associate html/htm files with Chrome in Windows 7 64 bit?

  - by matt

  I want Chrome to open all .html files. It is currently set as my default browser, however html files open in IE9. When I go to Control Panel\Programs\Default Programs\Set Associations I see that .html and .htm files are associated with IE. When I choose to change the default program it I'm presented with a list of programs but Chrome is not one of them. I browse to, and then select the Chrome.exe (C:\Users\Matt\AppData\Local\Google\Chrome\Application\chrome.exe) but it goes right back to IE. This is the first time I've seen anything like this. I'm running Windows 7 64 bit. I never had this problem on Windows 7 32 bit. Is this because Chrome by default installs in the User directory, not the Program Files directory? How can I fix these file associations? EDIT: It's not that things are reverting back to IE after associating them with Chrome. When I browse to Chrome in the file association window, and select it, it doesn't seem to take. It doesn't show Chrome in the list of programs despite pointing to the Chrome.exe location. I really think this has something to do with the fact that it doesn't install into the Program File Directory.

  Read the article

• Permissions nightmare - tried all I know

  - by Ben

  Working on a new client's dev site, which is a wordpress install on a Plesk box. I have SSH root access, and FTP access through a separate account. What I've done so far Initially I couldn't make any changes to any files at all. The permissions on all the template files looked a little screwy (644), so I figured change them to allow group, and add myself to the group: CHMOD Recursive on the theme folder to set everything to 664 Quickly realised I'd broken it, set the folders to 755, kept files as 664 Ownership on all files is a mixture of root:root and 500:500 (there is no user nor group with the ID of 500 on the server). Added myself to the group 'root' so I could modify the files too The Problem This worked OK, in terms of being able to edit the existing files, so I began working. However, I can't upload to the directory, even having run CHOWN -R root:root templatefolder/ and being in the root group. I feel like I must be missing something obvious, and it's doing my head in. Questions: Files in the install owned by 500 with group 500 - I've looked in /etc/group and /etc/passwd and there is no user nor group with this ID. Is that left over from another developer's setup or the previous server (they moved recently)? Is being in the 'root' group enough, or do I need to own the theme folder as 'myftpuser' in order to upload and create new files? Like I say, I have edit access, so I got myself this far. I'm now questioning what to do next!

  Read the article

• CentOS vps is randomly rebooting

  - by develroot

  I have a centos vps (Parallels Virtuozzo container) which has been running for months. However, a few days ago it started to randomly reboot itself, and i can't find out why. And the biggest problem that i don't understand is that it takes 40 minutes to reboot (as far as i can see in the logs) root ~ # cat /var/log/messages | grep shutdown Oct 11 13:52:11 vps27 shutdown[23968]: shutting down for system halt Oct 14 14:55:17 vps27 shutdown[30662]: shutting down for system halt Oct 15 06:21:23 vps27 shutdown[20157]: shutting down for system halt And notice the time difference between shutdown and xinetd's start: Oct 15 06:21:23 vps27 shutdown[20157]: shutting down for system halt Oct 15 06:21:24 vps27 init: Switching to runlevel: 0 Oct 15 06:21:27 vps27 saslauthd[30614]: server_exit : master exited: 30614 Oct 15 06:21:38 vps27 named[30661]: shutting down Oct 15 06:21:47 vps27 exiting on signal 15 Oct 15 07:04:34 vps27 syslogd 1.4.1: restart. Oct 15 07:05:06 vps27 xinetd[1471]: xinetd Version 2.3.14 started with libwrap loadavg labeled-networking options compiled in. Oct 15 07:05:06 vps27 xinetd[1471]: Started working: 0 available services And here's what Parallels Power Panel says in terms of Status Changes: Time Old Status Status Obtained Oct 15, 2011 06:23:46 AM Mounted Down Oct 15, 2011 06:22:31 AM Running Mounted Oct 14, 2011 03:06:48 PM Starting Running Oct 14, 2011 03:06:23 PM Down Starting Oct 14, 2011 03:06:08 PM Mounted Down Oct 14, 2011 02:58:24 PM Running Mounted For some reason it's getting into Mounting mode and then restarts itself. The only problem that i can imagine is disk space utilization, which is now 84%. But can that be a reson for system halt? Time Category Details Type Parameter Oct 15, 2011 07:08:33 AM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 82 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 15, 2011 06:27:23 AM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 82 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 15, 2011 06:23:50 AM Resource Resource counter_disk_share_used green alert on environment vps27 current value: 0 soft limit: hard limit: 0 Green zone counter_disk_share_used Oct 14, 2011 03:06:24 PM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 83 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 14, 2011 03:05:50 PM Resource Resource counter_disk_share_used green alert on environment vps27 current value: 0 soft limit: hard limit: 0 Green zone counter_disk_share_used

  Read the article

• Completely remove and freshly install MySql on XP?

  - by Corey Ogburn

  I have read this question and have not found it as a solution and I have even attempted much more. I've uninstalled MySql 5.5.18 and deleted: C:\Program Files\MySql C:\Documents and Settings\All Users\Application Data\MySql After uninstalling, I restart the computer. When I reinstall, in the MySql Server Instance Configuration Wizard I leave everything to their defaults except: I add a firewall exception I check Launch MySQL Server Automatically I check Include BIN directory in windows path Enable root access from remote machines (I'll lock that down later, just debugging for now, I have also tried installing without this option to no avail) I've tried Typical and Complete while installing, as well as with and without strict mode. No combination shows a difference. After all this, it cannot Apply Security Settings and I get a 10061 error (it also said error number 2003) and this article didn't help. I've tried everything I can to completely uninstall and successfully reinstall so I can start from scratch. I've uninstalled and reinstalled about a dozen times with minor changes (including turning off the firewall at times), each time deleting the above folders and any proper registry entries with no success. Note by success, applying security settings and a working remote connection. I can connect locally every time, but it's remotely that counts. I have tried to look for exterior problems such as port forwarding in the router and (even though the installer should add it) I do double check the firewall settings, which have always allowed the default port. I'm out of ideas.

  Read the article

• SQL Server 2008 Bring Database Online trying to open a file from a drive that doesn't exist

  - by Nai

  This is my error I am facing TITLE: Microsoft.SqlServer.Smo Set offline failed for Database 'Go3D_Retailer ------------------------------ ADDITIONAL INFORMATION: An exception occurred while executing a Transact-SQL statement or batch. (Microsoft.SqlServer.ConnectionInfo) Unable to open the physical file "E:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA\ftrow_Go3D_catalog.ndf". Operating system error 2: "2(failed to retrieve text for this error. Reason: 15105)". Database 'Go3D_Retailer' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. ALTER DATABASE statement failed. (Microsoft SQL Server, Error: 5120) Background to this error I've been trying to move my destination logshipping database to another physical server for analysis purposes. Because I do not have domain keys and active directory set up, I had to hack my process by using the same username/password for both the source and destination servers to get the process to work. Following that, I used this guy's solution to move the destination database to another server. However, this error occurs when I try to bring the database back online. I don't have an E drive on my server and I have no idea why it's trying to open a file from E drive. I have over a 100gb left on my hard disk so it's definitely not a space issue. This sounds like a bug... Any ideas?

  Read the article

• In an environment with multiple WiFi access points, do wireless clients sometimes connect to both at the same time?

  - by Bobby Burgess

  This is more of a curiosity than a problem, but in this new office I have two D-link DAP-2553's connected in a master/slave array (this just means the master keeps certain configuration options aligned with the slave). The network is set to 802.11n-only, and each AP has the same SSID and WPA2 key. The only difference is that they are on different channels (1 and 11). The WiFi network itself is working well. Users can roam around and the signal/speed is fairly consistent. However, I notice that when I look at the 802.11 client list in the web admin page for each of the 2 APs, I see that certain clients are connected to both, for extended periods of time, but I assume they are only passing data through one of them. Not every client is seen on each AP, but at any given time the same MAC address of a WiFi adapter can be associated (and remain associated) with both APs. The client list auto-refreshes every few seconds so I believe I'm looking at the most recent rather than stale information. One of the WiFi adapters that consistently associates with both APs is an Intel Centrino Wireless-N 1030 (laptop chip). Is it part of the WiFi standard that more than one association per WiFi card can be established concurrently on separate APS?

  Read the article

• What laptop would be recommended for video-editing or transcoding to blu-ray?

  - by Rob

  I'm looking for a machine (has to be a laptop) reasonably fast enough to handle editing/transcoding/rendering to Blu-ray disc of full true HD 1080p (1920x1080) video from a Samsung R10 camcorder - MPEG4 25fps (not the Sony-Panasonic AVCHD format): To be able to browse through the footage (say, quarter screen is fine for monitoring) and do simple edits - cut out bad bits, add titles, fades, nothing too fancy To be able to burn the footage in 1920x1080p 24p (twenty-four) fps to blu-ray, probably don't mind if I have to leave it for a few hours, or even overnight, as long as its not still running in the morning or takes days. I ALREADY have an external USB 2.0 LG BE06LU10 blu-ray burner. Does quad core make much difference? Or would Dual-core suffice for the above? NVidia because of CUDA for increased speed. What software today can take advantage of this? Which graphics card do I need? So far I've found Dell/Alienware to be well-specified, having a 5yr old Dell laptop that still runs well, albeit slow by today's standards, gives me a good impression. My concerns are too much fan-noise and budget and some Dell Precision Laptops exceed 1500 pounds. Thoughts?

  Read the article

• How can one make vim change terminal colors?

  - by amn

  I am using command line vim running from an xterm (which runs sh). I have color in vim according to a color scheme I like. The problem is, as usual with 256-color terminals and truecolor color schemes, colors are wrong. Now, I know I can do a gazillion things to fix this, including installing gvim, but I like my terminal. In fact, using xrdb [-merge] .Xresource file, I now actually have xterm override the color values, and the theme now looks perfect. Since, I may be switching to another theme, I need some workflow to have vim actually do what xrdb does - to reset terminal color pallette. Because right now I have to reset color values with xrdb ... first, then launch another xterm to actually use these values, then launch vim from that newly opened xterm to have the exact colors. The way I understood it is that vim color scheme, just as any other terminal application, uses colors by referencing their ids, and X resources set the values themselves. I think I saw somewhere on Internet, that terminal control character sequences can reset actual color values, in fact, I am sure they can - I managed to set my terminal background color at runtime. How would I make vim execute these sequences to match values for the color scheme? And is there any reference to these control sequences, as part of any standard?

  Read the article

• VirtualBox VM running web server not accessible via external IP

  - by mwigdahl

  I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

  Read the article

• Can a pool of memcache daemons be used to share sessions more efficiently?

  - by Tom

  We are moving from a 1 webserver setup to a two webserver setup and I need to start sharing PHP sessions between the two load balanced machines. We already have memcached installed (and started) and so I was pleasantly surprized that I could accomplish sharing sessions between the new servers by changing only 3 lines in the php.ini file (the session.save_handler and session.save_path): I replaced: session.save_handler = files with: session.save_handler = memcache Then on the master webserver I set the session.save_path to point to localhost: session.save_path="tcp://localhost:11211" and on the slave webserver I set the session.save_path to point to the master: session.save_path="tcp://192.168.0.1:11211" Job done, I tested it and it works. But... Obviously using memcache means the sessions are in RAM and will be lost if a machine is rebooted or the memcache daemon crashes - I'm a little concerned by this but I am a bit more worried about the network traffic between the two webservers (especially as we scale up) because whenever someone is load balanced to the slave webserver their sessions will be fetched across the network from the master webserver. I was wondering if I could define two save_paths so the machines look in their own session storage before using the network. For example: Master: session.save_path="tcp://localhost:11211, tcp://192.168.0.2:11211" Slave: session.save_path="tcp://localhost:11211, tcp://192.168.0.1:11211" Would this successfully share sessions across the servers AND help performance? i.e save network traffic 50% of the time. Or is this technique only for failovers (e.g. when one memcache daemon is unreachable)? Note: I'm not really asking specifically about memcache replication - more about whether the PHP memcache client can peak inside each memcache daemon in a pool, return a session if it finds one and only create a new session if it doesn't find one in all the stores. As I'm writing this I'm thinking I'm asking a bit much from PHP, lol... Assume: no sticky-sessions, round-robin load balancing, LAMP servers.

  Read the article

• Trouble getting latest version of Git

  - by TheMethod

  I am using Ubuntu 10.04 LTS. I'm looking at using git as source control for personal projects and Github as a remote repository. I was having trouble pushing a commit to my remote github repo getting the following error message: The requested URL returned error: 403 while accessing https://github.com/Jstall/helloworld.git/info/refs When I did some digging I found that the problem could be me not having the latest version of Git. When I did a --version I found that I have version 1.7.0.4 locally. So I tried to update git using: sudo apt-get install git but get the following error: Reading package lists... Done Building dependency tree Reading state information... Done Package git is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package git has no installation candidate I've tried running: sudo apt-get update and trying again but it didn't seem to make a difference. I'm not sure if it's relevant but I'm also getting a couple of 404's when I run update: Err http://wine.budgetdedicated.com edgy/main Packages 404 Not Found Fetched 4,117B in 0s (5,142B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/edgy/universe/binary-i386/Packages.gz 404 Not Found [IP: 91.189.91.15 80] W: Failed to fetch http://wine.budgetdedicated.com/apt/dists/edgy/main/binary-i386/Packages.gz 404 Not Found I'm not sure when I should try next. Could anyone suggest a course of action to get this resolved? Any advice would be appreciated. Thanks much!

  Read the article

• Mac OS X duplex printing problem: one- vs. multi-paged documents

  - by Christian Lindig

  I like to print on pre-printed stationery using the Preview.app and a duplex-capable HP Color Laserjet 4700 (PostScript) printer. The print dialog handles one and two-paged documents differently: the paper needs to be placed differently into the tray if the document contains one page versus when it contains two pages. This is not obvious when printing on plain paper but becomes obvious when front and reverse side of sheets are marked. Otherwise the first page would end up on the reverse side of the first sheet. I believe the problem is caused by the printer driver setting duplex printing to false (using the PostScript setpagedevice operator) when emitting a single-page document versus keeping it set to true when emitting multi-page documents. All this despite that duplex printing is always specified in the printer dialog. When printing a single-sided document, duplex=true and duplex=false seem to make a difference with respect which side of a sheet gets printed on. It would be also helpful if others could confirm the problem actually exists. I suspect this problem is not limited to specific printers. I'm on OS X 10.6 and I checked two different HP printers.

  Read the article

• Networking 2 Virtual PC with one VPC as DHCP server

  - by vivek

  My host OS is Win XP Professional. The host has a real network connection via DSL and I created a second network connection using Microsoft Loopback Adapter. Internet connection sharing is enabled. The Microsoft Loopback adapter has a IP address of 192.168.0.1. I have 1 Virtual PC which has Windows Server 2003. I have setup the network connection on this VPC to use Microsoft Loopback Adapter. I setup this VPC to be the Domain Controller , DNS Server and DHCP Server. I set this to a static IP address 192.168.0.2 (on the same subnet as the MS Loopback adapter) I have a second Virtual PC which also has Windows Server 2003. The network connection on this VPC is set to "Local Only". I want this VPC to get its IP address from the 1st VPC on which I setup as a DHCP server. What i want is the 2 VPC should be in a network with one of the VPC acting as the domain controller, DNS Server and DHCP server. The second VPC shoud get its IP address from the 1st VPC. It should be a part of the domain of the 1st VPC. When i tried to make the second VPC get the IP address from the first VPC I am not succeeding. Can somebody post some suggestions on how to go about this ?

  Read the article

• Issue with multiple bridging for KVM hosts

  - by Henry-Nicolas Tourneur

  I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

  Read the article

• Can I get a domain controller not to act as DNS for the members?

  - by rsw

  Hi, Let me try to explain my current setup. I have one linux machine acting as DHCP and DNS (dhcpd3 and bind) in my network. This works fine, all computers I hook up to the network gets an IP address and proper DNS servers set. Let's call it 10.12.0.10 However, we also have a Windows Server 2003 Domain Controller in our network to which we add our Windows computers (running XP), let's call it 10.12.0.20. I noticed that when I run 'nslookup' on one of the windows machines, it says that the primary DNS is 10.12.0.20. This have not been much of a problem since: The Windows clients are stationary The Windows server in itself point out my real DHCP/DNS, since I can reach everything specified in it However, this turns out to be a problem when we use Laptops. They connect to the domain here and gets a DNS server, but when the user travels or connect the computer from home, we hit a problem. They are connected to their internet, but their DNS is 10.12.0.20 which they can't reach since they're at home and not at the office network. I solved this by removing the register key called "NameServer" with the value 10.12.0.20, but it gets set again whenever they logon to the domain the next time (when they get back to the office). Can I somehow make the computers take whatever DNS server they are handed when connecting to the internet or a home network, instead of always trying to reach the Domain Controller?

  Read the article

• Juniper SSG 5 VPN

  - by Ethabelle

  I have a host who set up our Juniper SSG 5 VPN with Firmware version-6.2.0r5.0 I've been trying to set up VPN on it using this guide: http://kb.juniper.net/InfoCenter/index?page=content&id=KB4094 I've followed the steps and on my Mac, whenever I try to connect using L2TP over IPSec I get the following error; Summary of Steps: Create User (give them L2TP auth ability), Create Group, Place User in Group, Create VPN Gateway, Create VPN, create IP Pool, change default L2TP settings, create Untrust Trust Policy. The L2TP-VPN server did not respond. Try reconnecting. If the problem continues, verify your settings and contact your Administrator. I looked in my Firewall's logs, but I don't even see anything under Reports Logs Events. I'm.. obviously missing something, I just don't know what I'm missing at this point. I'm just starting networking and this is sort of Step 101 and I'm getting annoyed and just want to throw up OpenVPN, but I've read that has problems with Juniper Firewalls. Hooray.

  Read the article

• How to change the spell checking language in Chromium?

  - by mote

  When write I need spell checking in Danish or English (one at a time, not both at the same time), but changing from one language to the other is not working well for me. Example: Writing an email in English, everything is underlined as misspelled because the spelling language is set to Danish. I then right-click the text field and choose "Spell-checker Options" and set the language to English. But is does not change the language. Only after I try maybe 4-5 times it does. Selecting the text, clicking it, clicking the background, click the text, I have tried it all but I cannot figure out how it works. Sometimes it changes on first try, sometimes I have to do it 6-7 times. Searching brings lots of a known bugs stating that Chromium does not re-check the text after changing the language. But that is not what drives me crazy, for starters being able to change the language in the first try would be nice. It is not a fault in my installation, I have the same problem on 3 computers. Does any know something that I don't?

  Read the article

• Share Firefox/Thnderbird data between W7 and Linux Mint 12 in dual boot computer

  - by Albert

  I've just set up my laptop (where I had running only W7) with a dual boot to run Linux Mint 12 as well. I have a "Data" partition (apart from the required partitions for W7 and Linux) where I store pretty much everything that isn't software installations (music, videos, project files, etc). I seem to be able to access that NTFS partition totally fine from Mint (like I've always done with W7), which is cool because I can access all that stuff regardless of which OS I'm using. I would like to know if it's possible (and how) to go one step further and share programs data between the two OS. One example would be my Firefox and Thunderbird data. For example, in Firefox share my bookmarks (and if I could share history, autocomplete and all that stuff, that would be awesome). In thunderbird, be able to share my mail and configuration, seeing the same inbox, folders, message rules, etc... So if I receive/send an email from W7 and later switch to Mint, I can see that email as it had been received/sent from Mint, and vice versa. Is this even possible? Or am I asking for too much convenience? If it's possible, any clues on how to set it all up?

  Read the article

• CloudFront for dynamic content CDN

  - by Elad Lachmi

  I would like to use CF as a CDN for my entire site, including static and dynamic content. I have been using CF for static content for a while and I am very happy with the results. I am now doing POC of putting the web server completely behind CF. For the dynamic content I created a new distribution and set the origin to be my web server. Right now I'm looking to test the solution, so I have the web server on the original domain and the CF distribution on the amazon domain. This works with the exception of HTTPS urls and POST requests. For HTTPS requests, I see the requests are forwarded to the original site domain for now, but how will CF handle them when I move the distribution to the www cname? What configuration changes should I make so that CF forwards HTTPS requests to the origin? For POST requests, I want the post to be made to the origin server. Can I set this up in CF? Finally, the site has membership. Can I configure CF to pull all content from the origin if the user is logged in? Sorry for the long question. I'm a little lost and documentation for dynamic CF is still kind of scarce. Thank you!

  Read the article

• iptables to block non-VPN-traffic if not through tun0

  - by dacrow

  I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

  Read the article

• Why java -version returning a different version than the one defined in JAVA_HOME?

  - by Shekhar

  I am trying to set JAVA_HOME in Ubuntu OS. I have copied jdk 1.7 in /usr/lib/jvm and set JAVA_HOME in /etc/profile file. Contents of /usr/lib/jvm folder are as follows : shekhar@ubuntu:~$ ls /usr/lib/jvm/ default-java java-1.6.0-openjdk java-6-openjdk java-6-openjdk-i386 jdk1.7.0_01 java-1.5.0-gcj-4.6 java-1.6.0-openjdk-i386 java-6-openjdk-common java-7-openjdk-i386 and last few lines of /etc/profile file are as follows : export JAVA_HOME=/usr/lib/jvm/jdk1.7.0_01 export PATH=$PATH:$JAVA_HOME/bin After finishing all this when I run java -version command I get following output : shekhar@ubuntu:~$ java -version java version "1.6.0_24" OpenJDK Runtime Environment (IcedTea6 1.11.4) (6b24-1.11.4-1ubuntu0.12.04.1) OpenJDK Server VM (build 20.0-b12, mixed mode) and when I run ls -lah command I get following output : shekhar@ubuntu:~$ ls -lah /usr/bin/java lrwxrwxrwx 1 root root 22 Sep 29 09:58 /usr/bin/java -> /etc/alternatives/java shekhar@ubuntu:~$ ls -lah /etc/alternatives/java lrwxrwxrwx 1 root root 45 Sep 29 09:58 /etc/alternatives/java -> /usr/lib/jvm/java-6-openjdk-i386/jre/bin/java Can anyone please tell me which thing I am missing? Why Ubuntu is still pointing to open jdk and not to my jdk 7? PS : I have seen this similar question and its answers but that question is related to Windows OS and not for Ubuntu so I am reposting this similar question for Ubuntu.

  Read the article

< Previous Page | 939 940 941 942 943 944 945 946 947 948 949 950  | Next Page >