Search Results

Search found 27232 results on 1090 pages for 'mind mapping software'.

Page 955/1090 | < Previous Page | 951 952 953 954 955 956 957 958 959 960 961 962  | Next Page >

• Using mixed disks and OpenFiler to create RAID storage

  - by Cylindric

  I need to improve my home storage to add some resilience. I currently have four disks, as follows: D0: 500Gb (System, Boot) D1: 1Tb D2: 500Gb D3: 250Gb There's a mix of partitions on there, so it's not JBOD, but data is pretty spread out and not redundant. As this is my primary PC and I don't want to give up the entire OS to storage, my plan is to use OpenFiler in a VM to create a virtual SAN. I will also use Windows Software RAID to mirror the OS. Partitions will be created as follows: D0 P1: 100Mb: System-Reserved Boot D0 P2: 50Gb: Virtual Machine VMDKs for OS D0 P3: 350Gb: Data D1 P1: 100Mb: System-Reserved Boot D1 P2: 50Gb: Virtual Machine VMDKs for OS D1 P3: 800Gb: Data D2 P1: 450Gb: Data D3 P1: 200Gb: Data This will result in: Mirrored boot partition Mirrored Operating system Mirrored Virtual machine O/S disks Four partitions for data In the four data partitions I will create several large VMDK files, which I will "mount" into OpenFiler as block-storage devices, combined into three RAID arrays (due to the differing disk sizes) In effect, I'll end up with the following usable partitions SYSTEM 100Mb the small boot partition created by the Windows 7 installer (RAID-1) HOST 50Gb the Windows 7 partition (RAID-1) GUESTS 50Gb Virtual machine Guest VMDK's (RAID-1) VG1 900Gb Volume group consisting of a RAID-5 and two RAID-1 VG2 300Gb Volume group consisting of a single disk On VG1 I can dynamically assign storage for my media, photographs, documents, whatever, and it will be safe. On VG2 I can dynamically assign storage for my data that is not critical, and easily recoverable, as it is not safe. Are there any particular 'gotchas' when implementing a virtual OpenFiler like this? Is the recovery process for a failing disk going to be very problematic? Thanks.

  Read the article

• How small (spec wise) can a virtual machine be and still boot up and run some sort of OS?

  - by IllvilJa

  One of the advantages with virtual machines is that you can be very flexible with their sizes. If the host system permits it, you can have a very large virtual machine with a lot of virtual RAM and disk. Also, you can decide to go the other way around, to give the virtual machine a very modest amount of RAM and disk and then choose and configure the OS appropriately. The question is, how small virtual machines have people managed to setup (and get to both boot up and to run)? Virtual machines doing something usuful is preferable, even if I know "useful" in this context is awfully subjective, but laboratory-cases with a configuration stripped beyond common sense could be intresting as well, just to see what people manage to boot and run. Quite open ended question and quite academic, but think of it: an extremely small VM (which still does something useful) takes very little memory and disk and can be quite quickly saved to and restored from disk. If it's also gentle on CPU resources, one might consider having a huge number of such VMs up and running on a host. (Imagine a VM running just an old Commodore 64 or Commodore Amiga in it. Ok, way wrong CPU architecture for modern Virtualization software running on a x86-based PC but still an interesting thought. You could have quite a few such small VMs running on a modern PC.)

  Read the article

• Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

  - by Bo102010

  (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

  Read the article

• Can't login via ssh after upgrading to Ubuntu 12.10

  - by user42899

  I have an Ubuntu 12.04LTS instance on AWS EC2 and I upgraded it to 12.10 following the instructions at https://help.ubuntu.com/community/QuantalUpgrades. After upgrading I can no longer ssh into my VM. It isn't accepting my ssh key and my password is also rejected. The VM is running, reachable, and SSH is started. The problem seems to be about the authentication part. SSH has been the only way for me to access that VM. What are my options? ubuntu@alice:~$ ssh -v -i .ssh/sos.pem [email protected] OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/ubuntu/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to www.hostname.com [37.37.37.37] port 22. debug1: Connection established. debug1: identity file .ssh/sos.pem type -1 debug1: identity file .ssh/sos.pem-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: RSA 33:33:33:33:33:33:33:33:33:33:33:33:33:33 debug1: Host '[www.hostname.com]:22' is known and matches the RSA host key. debug1: Found key in /home/ubuntu/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: .ssh/sos.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password [email protected]'s password: debug1: Authentications that can continue: publickey,password Permission denied, please try again.

  Read the article

• apache-user & root access

  - by ahmedshaikhm

  I want to develop few scripts in php that will invoke following commands; using exec() function service network restart crontab -u root /xyz/abc/fjs/crontab etc. The issue is that Apache executes script as apache user (I am on CentOS 5), regardless of adding apache into wheel or doing good, the bad and the ugly group assignment does not run commands (as mentioned above). Following are my configurations; My /etc/sudoers root ALL=(ALL) ALL apache ALL=(ALL) NOPASSWD: ALL %wheel ALL=(ALL) ALL %wheel ALL=(ALL) NOPASSWD: ALL As I've tried couple of combination with sudoer & httpd.conf, the recent httpd.conf look something as follows; my httpd.conf User apache Group wheel my PHP script exec("service network start", $a); print_r($a); exec("sudo -u root service network start", $a); print_r($a); Output Array ( [0] => Bringing up loopback interface: [FAILED] [1] => Bringing up interface eth0: [FAILED] [2] => Bringing up interface eth0_1: [FAILED] [3] => Bringing up interface eth1: [FAILED] ) Array ( [0] => Bringing up loopback interface: [FAILED] [1] => Bringing up interface eth0: [FAILED] [2] => Bringing up interface eth0_1: [FAILED] [3] => Bringing up interface eth1: [FAILED] ) Without any surprise, when I invoke restart network services via ssh, using similar user like apache, the command successfully executes. Its all about accessing such commands via HTTP Protocol. I am sure cPanel/Plesk kind of software do use something like sudoer or something and what I am trying to do is basically possible. But I need your help to understand which piece I am missing? Thanks a lot!

  Read the article

• corrupted, hidden, wireless network adapter from "Network Connections" in Windows 7

  - by srihari reddy

  The issue is that when I install a wireless network adapter on my Windows 7 Professional machine I have no connectivity, the system tray icon has a red X. First, I tried the obvious, install updated drivers from the manufacturer. When I did this, the Network Connections icon had gray bars and there was no connectivity. So I tried installling the network adapter on a different computer on the same network and I verified that it does work with no issues. Next, I ran scan disk with no issues. Next, I ran sfc as admin with no issues. At this point I turned to the router and turned SSID broadcast on but that didn't help. I turned MAC address filtering off at the router but that didn't help. Whenever I installed the original network adapter (a wireless N usb adapter with WPA2 TKIP+AES) it showed up as "Wireless Network Connection 2" with a grayed out icon and no connectivity. Lastly, I tried installing two different "verified working" usb wireless adapters on to the Windows 7 Pro machine. The results were the same "Wireless Network Connection 2" that had a green bar icon but no connectivity. I installed the manufacturers software and it indicated the NIC was not there even thought the driver installed successfully in Device Manager. I guess I should mention, I first tried (insanely in vain) to use the (worthless) Windows Network troubleshooter. The results were....drumroll please... There is a problem with the network adapter... well No Duh! Also, during all of this the network adapter is always showing as "Working Properly" in the properties dialogue of Device Manager for the wireless NIC. I checked for hidden devices in Device Manager but there were none. Here is my fundamental question that I've tried to find in the Windows 7 support center with no luck. How do I remove/delete/uninstall network adapters from the Windows 7 registry? in particular hidden, corrupted network adapters, that used to be working.

  Read the article

• RemoteApp .rdp embed creds?

  - by Chris_K

  Windows 2008 R2 server running Remote Desktop Services (what we used to call Terminal Services back in the olden days). This server is the entry point into a hosted application -- you could call it Software as a Service I suppose. We have 3rd party clients connecting to use it. Using RemoteApp Manager to build RemoteApp .rdp shortcuts to distribute to client workstations. These workstations are not in the same domain as the RDS server. There is no trust relationship between domains (nor will there be). There is a tightly controlled site to site VPN between workstations and the RDS server, we're quite confident we have access to the server locked down. The remoteApp being run is an ERP application with its own authentication scheme. The issue? I'm trying to avoid the need to create AD logins for every end user when connecting to the RemoteApp server. In fact, since we're doing a remoteApp and they have to authenticate to that app, I'd rather just not prompt them at all for AD creds. I certainly don't want them caught up in managing AD passwords (and periodic expirations) for accounts they only use to get to their ERP login. However, I can't figure out how to embed AD creds in a RemoteApp .rdp file. I don't really want to turn off all authentication on the RDS server at that level. Any good options? My goal is to make this as seamless as possible for the end-users. Clarifying questions are welcome.

  Read the article

• How to connect to a computer that is in Sleep mode over the internet

  - by Gerhard Weiss

  How to connect to a computer that is in Sleep mode over the internet? I am using LogMeIn to connect to another computer offsite. I just installed Windows 7 RC on that system and found that the Sleep mode actually works. Currently LogMeIn does not connect when the system is in Sleep mode or Hibernate mode (that is what their error message displays when you try). Is there a way to get LogMeIn to connect to a system in Sleep mode? Is there other software that gives simliar LogMeIn functionallity (like RDP, etc.) that could be used on Windows 7 instead. I just use LMI for connecting and nothing else (no printing or file transfers). A Non-expensive options (such as free) would be better. I have seen web sites mentioning "Wake on LAN". Does anyone have some good links on how to set this up to be accessed over the internet? Edited: It looks like LogMeIn BETA might be the solution. https://beta.logmein.com/welcome/nextgen/ Has anyone tried this beta yet?

  Read the article

• Intel Atom overheating in ASUS EEE Box 1501P

  - by Sergey L.

  I have had an ASUS EEE Box 1501P for just a little bit over a year. Of course it breaks 2 months after the warranty runs out. http://www.asus.com/Eee/EeeBox_PC/EeeBox_PC_EB1501P/ I have been using the box as a Home Media Center. Running mostly 24/7 often pausing a video overnight. Since last week the fan started running extremely loud. After some digging I found that the Intel Atom CPU in it is overheating and the built-in sensor is reporting temperatures way over 105°C. This got me worried, so I took the unit apart. Completely vacuumed the heat sink, oiled the fan, but the unit is still showing the same behaviour. After turning it on and just observing the hardware monitor in the BIOS the temperature slowly rises from 40°C to over 95°C in appx 5 min. I am running the newest BIOS and a lightweight Linux OPENELEC OS with XBMC on it. Now I am wondering if it could be a faulty heat sensor in the Atom. Recommended running temperature is up to 85°C, but I have not detected any performance hits when running at the above mentioned 105°C and there seem to be no software faults. How can an Atom with an attached heat sink and a fan running at full capacity even get this hot in the first place at 0 load? Aren't those things designed to generate virtually no heat? Could it be a faulty heat sensor? What shall I try to fix this? I would prefer not to damage the CPU, since it is hard fused into the motherboard and cannot be replaced. I could remove the heat pipe/heat sink, but it is getting hot, so heat is properly transferring from the CPU to the heat pipe, the fan is running at full capacity, is recently oiled and warm air is making it out of the exhaust. Edit: One more note: The North-bridge (or whatever it is called nowadays) is on the same heat pipe.

  Read the article

• Nvidia GTS 360M in Asus laptop shuts off when gaming on external display

  - by mr odus

  I have had this problem on my Asus G51j Intel I5, Nvidia GTS360M graphics card. Just updated the drivers to latest off Nvidias site. Most games I play, If I hook it up through an external monitor(this happens whether it's HDMI or VGA). The laptop hard shuts down after about 20 minutes, give or take. This tends to happen on more graphically intense games like Call of dutys, bioshock. I'm running Windows 7, latest nvidia drivers. Games work fine on my laptops screen, and Movies, general computing work fine on the external displays. The laptop always sits on a cooling pad and the latest time was in front of my AC unit, I ran heatfan or whatever the heat tracking software was, and my temperatures were normal through a shut down. This has been happening for the life of the laptop. I dont play very many games, and even fewer on an external monitor, so this issue doesnt come up much Is it possible I have a faulty graphics card? Is there anything else I can try?

  Read the article

• Convert mp4 video to a format xbox 360 can play

  - by Björn Lindqvist

  Here is a video file my Xbox 360 refuses to play: $ MP4Box -info video.mp4 * Movie Info * Timescale 90000 - Duration 02:18:33.365 Fragmented File no - 2 track(s) File Brand mp42 - version 0 Created: GMT Sat Jul 21 07:08:55 2012 File has root IOD (9 bytes) Scene PL 0xff - Graphics PL 0xff - OD PL 0xff Visual PL: ISO Reserved Profile (0x7f) Audio PL: High Quality Audio Profile @ Level 2 (0x0f) No streams included in root OD iTunes Info: Encoder Software: HandBrake 0.9.6 2012022800 Track # 1 Info - TrackID 1 - TimeScale 90000 - Duration 02:18:33.235 Media Info: Language "Undetermined" - Type "vide:avc1" - 199318 samples Visual Track layout: x=0 y=0 width=1280 height=688 MPEG-4 Config: Visual Stream - ObjectTypeIndication 0x21 AVC/H264 Video - Visual Size 1280 x 688 AVC Info: 1 SPS - 1 PPS - Profile High @ Level 4.1 NAL Unit length bits: 32 Self-synchronized Track # 2 Info - TrackID 2 - TimeScale 48000 - Duration 02:18:33.365 Media Info: Language "English" - Type "soun:mp4a" - 389689 samples MPEG-4 Config: Audio Stream - ObjectTypeIndication 0x40 MPEG-4 Audio MPEG-4 Audio AAC LC - 6 Channel(s) - SampleRate 48000 Synchronized on stream 1 $ avconv -i video.mp4 avconv version 0.8.4-4:0.8.4-0ubuntu0.12.04.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:33 with gcc 4.6.3 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'video.mp4': Metadata: major_brand : mp42 minor_version : 0 compatible_brands: mp42isomavc1 creation_time : 2012-07-21 07:08:55 encoder : HandBrake 0.9.6 2012022800 Duration: 02:18:33.36, start: 0.000000, bitrate: 2299 kb/s Stream #0.0(und): Video: h264 (High), yuv420p, 1280x688, 1973 kb/s, 23.98 fps, 90k tbr, 90k tbn, 180k tbc Metadata: creation_time : 2012-07-21 07:08:55 Stream #0.1(eng): Audio: aac, 48000 Hz, 5.1, s16, 319 kb/s Metadata: creation_time : 2012-07-21 07:08:55 At least one output file must be specified What tool, such as ffmpeg or mencoder, and what magic command line incantation should I use to transcode this file into a format Xbox 360 can play? I want the transcode process to retain as good video quality as possible.

  Read the article

• DIR $file "File Not Found" vs DIR $filedir shows it....not permissions, not USB

  - by Kev

  I was having this problem before on a USB drive, but now it's happening on my main RAID5-backed hard disk: 2013-10-17 9:37 C:\>dir "C:\Shares\Shared\Reference\Safety Management System\Vid eo CD\AutoPlay\Docs\Manuel*" Volume in drive C has no label. Volume Serial Number is 3C18-E114 Directory of C:\Shares\Shared\Reference\Safety Management System\Video CD\AutoP lay\Docs 2003-09-09 11:29 PM 1,056,768 Manuel d'intervention d'urgence MFC.doc 2004-06-20 10:36 PM 139,849 Manuel d'intervention d'urgence MFC.pdf 2 File(s) 1,196,617 bytes 0 Dir(s) 196,068,691,968 bytes free 2013-10-17 9:38 C:\>dir "C:\Shares\Shared\Reference\Safety Management System\Vid eo CD\AutoPlay\Docs\Manuel d'intervention d'urgence MFC.doc" Volume in drive C has no label. Volume Serial Number is 3C18-E114 Directory of C:\Shares\Shared\Reference\Safety Management System\Video CD\AutoP lay\Docs File Not Found 2013-10-17 9:38 C:\> This is from a Command Prompt window where I went to Properties and told it I wanted to modify who it ran as. I opened it, had it run as me with the "restricted access" unchecked, then ran the above. The file in question has the following ACLs: Administrators, SYSTEM, and OurCompanyUsers. All three have full control of everything. Nobody has any Deny bits set. I am a member of Administrators. So I don't believe it's a permissions issue. It's not a USB drive, so this time there is no question of USB hardware. Windows Server 2003 Standard Edition SP2. What does this mean? Is this more likely a hardware or software problem?

  Read the article

• How does the LeftHand SAN perform in a Production environment?

  - by Keith Sirmons

  Howdy, I previously asked this ServerFault question: Does anyone have experience with lefthands VSA SAN The general consensus looks like it does not perform well enough for a production SQL server even at a light load. So the new question is, How does LeftHand's SAN perform on the HP or Dell dedicated Hardware boxes? We are looking at the Starter SAN with 2 HP nodes in a 2-way replication, 2 ESX servers hosting a total of 2 Active Directory server, 1 MS SQL server, 1 File Server, and 1 General Purpose Server for things like Virus Scan (All Microsoft Server 2005 or 2008). The reason I am looking at LeftHand is for the complete software package. I plan to have a DR site and like how the SAN can perform an Async Replication to the offsite location without having to go back to the Vendor for more licenses. I also like the redundancy built into the Network Raid architecture. I have looked at other SANS and found different faults with them. For example, Dell's EqualLogic: Found that although the individual box is very redundant in hardware, the Data once spanned across multiple boxes is not redundant, if a node goes down you have lost the only copy of the data sitting on that hardware (One thing is certain, all hardware fails... When? is the only question.). I have used an XioTech SAN as well.. Well worth the money BTW, but I think it is overkill for the size of the office I am targeting. The cost to get the hardware redundancy in the XioTech makes it a little out of reach for the budget I am working in. Thank you, Keith

  Read the article

• Webcam becomes "Unknown Device" after Windows Messenger 2011 is installed

  - by Boris

  I have Sony VAIO VGN-NS290J laptop. I installed Windows 7 Ultimate 64-bit. I was able to find drivers for all hardware without any problems. Recently, I installed Microsoft Windows Live Essentials 2011, i.e. Windows Live Messenger 2011. Ever since that application is running on my computer, my webcam is not recognized by the OS any more. It is listed as the "Unknown Device" and placed in the Universal Serial Bus controllers group in the Device Manager. There don't seem to be any drivers for this webcam. It's a standard Sony Motion Eye web camera and Sony does not offer any drivers for it. There is one application to download that utilizes the camera, but there are no drivers (and the system is showing the same behavior regardless of the presence of the application). It happens from time to time that the webcam becomes recognized by the OS again, after a couple of restarts; but not always. Then it becomes unknown again. I am absolutely positive that this issue is caused by the Windows Live Messenger 2011, because same symptoms caused the same effects before. I wish to be able to continue to use this software, but also to use my webcam. I was wondering if anyone had a similar issue and if there is a way to fix it. Thanks for all the help, I appreciate it. Update: I have discovered a pattern - if the camera goes astray, restarting the machine does not bring it back; but switching the computer off and turning it back on does. Every time! This is getting super complicated :)

  Read the article

• How to make Exchange 2003 non-authoritive

  - by Romski

  Background We are a small company with an internally hosted Exchange 2003. It receives email for 2 domains (the company was renamed a few years back). For the sake of argument, the domains are: oldname.com newname.com We have moved newname.com to a hosted exchange service, and our DNS record is correctly routing emails. Our internal server still receives email for oldname.com, although we have asked our hosting company to accept emails for that domain. Problem My problem is that emails generated internally from monitoring software, printer, etc. are being caught by our (defunct) internal server and being delivered to the old mailboxes. I believe that what is happening is that our internal exchange server considers itself to be the authoritive server for newname.com. I think it must be looking in active directory for a mailbox and delivering it internally without ever going outside. Attempt to fix I started to follow the article here: http://support.microsoft.com/kb/321721. I removed the SMTP recipient policy for newname.com, and added a dummy address and made it primary. I also answered yes for updating the associated emails. I then restarted the Microsoft Exchange Routing System and SMTP, but emails are still being routed internally. Is there a way to force the exchange server to route all emails for the domain newname.com to the new hosted service?

  Read the article

• Postfix on Snow Leopard unable to send MIME emails, including header contents in message body

  - by devvy

  I configured postfix on snow leopard by adding the following line to /etc/hostconfig: MAILSERVER=-YES- I then configured postfix to relay through my ISP's SMTP server. I added the following two lines in their respective places within /etc/postfix/main.cf: myhostname = 1and1.com relayhost = shawmail.vc.shawcable.net I then have a simple PHP mail function wrapper as follows: send_email("[email protected]", "[email protected]", "Test Email", "<p>This is a simple HTML email</p>"); echo "Done"; function send_email($from,$to,$subject,$message){ $header="From: <".$from."> "; $header.= 'MIME-Version: 1.0' . " "; $header.= 'Content-type: text/html; charset=iso-8859-1' . " "; $send_mail=mail($to,$subject,$message,$header); if(!$send_mail){ echo "ERROR"; } } With this, I am receiving an e-mail that appears to be improperly formatted. The message header is showing up in the body of the e-mail. The raw message content is as follows: Return-Path: <[email protected]> Delivery-Date: Tue, 27 Apr 2010 18:12:48 -0400 Received: from idcmail-mo2no.shaw.ca (idcmail-mo2no.shaw.ca [64.59.134.9]) by mx.perfora.net (node=mxus2) with ESMTP (Nemesis) id 0M4XlU-1NCtC81GVY-00z5UN for [email protected]; Tue, 27 Apr 2010 18:12:48 -0400 Message-Id: <[email protected]> Received: from pd6ml3no-ssvc.prod.shaw.ca ([10.0.153.149]) by pd6mo1no-svcs.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:47 -0600 X-Cloudmark-SP-Filtered: true X-Cloudmark-SP-Result: v=1.0 c=1 a=VphdPIyG4kEA:10 a=hATtCjKilyj9ZF5m5A62ag==:17 a=mC_jT1gcAAAA:8 a=QLyc3QejAAAA:8 a=DGW4GvdtALggLTu6w9AA:9 a=KbDtEDGyCi7QHcNhDYYwsF92SU8A:4 a=uch7kV7NfGgA:10 a=5ZEL1eDBWGAA:10 Received: from unknown (HELO 1and1.com) ([24.84.196.104]) by pd6ml3no-dmz.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:48 -0600 Received: by 1and1.com (Postfix, from userid 70) id BB08D14ECFC; Tue, 27 Apr 2010 15:12:47 -0700 (PDT) To: [email protected] Subject: Test Email X-PHP-Originating-Script: 501:test.php Date: Tue, 27 Apr 2010 18:12:48 -0400 X-UI-Junk: AutoMaybeJunk +30 (SPA); V01:LYI2BGRt:7TwGx5jxe8cylj5nOTae9JQXYqoWvG2w4ZSfwYCXmHCH/5vVNCE fRD7wNNM86txwLDTO522ZNxyNHhvJUK9d2buMQuAUCMoea2jJHaDdtRgkGxNSkO2 v6svm0LsZikLMqRErHtBCYEWIgxp2bl0W3oA3nIbtfp3li0kta27g/ZjoXcgz5Sw B8lEqWBqKWMSta1mCM+XD/RbWVsjr+LqTKg== Envelope-To: [email protected] From: <[email protected]> MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 Message-Id: <[email protected]> Date: Tue, 27 Apr 2010 15:12:47 -0700 (PDT) <p>This is a simple HTML email</p> And here are the contents of my /var/log/mail.log file after sending the email: Apr 27 15:29:01 User-iMac postfix/qmgr[705]: 74B1514EDDF: removed Apr 27 15:29:30 User-iMac postfix/pickup[704]: 25FBC14EDF0: uid=70 from=<_www> Apr 27 15:29:30 User-iMac postfix/master[758]: fatal: open lock file pid/master.pid: unable to set exclusive lock: Resource temporarily unavailable Apr 27 15:29:30 User-iMac postfix/cleanup[745]: 25FBC14EDF0: message-id=<[email protected]> Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: from=<[email protected]>, size=423, nrcpt=1 (queue active) Apr 27 15:29:30 User-iMac postfix/smtp[747]: 25FBC14EDF0: to=<[email protected]>, relay=shawmail.vc.shawcable.net[64.59.128.135]:25, delay=0.21, delays=0.01/0/0.1/0.1, dsn=2.0.0, status=sent (250 ok: Message 25784419 accepted) Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: removed Two other people in the office have followed the exact same process and are running the exact same script, version of snow leopard, php, etc. and everything is working fine for them. I've even copied their config files to my machine, restarted postfix, restarted apache, all to no avail. Does anyone know what steps I could take to resolve the issue? This is boggling my mind... Thanks

  Read the article

• Managing a test iSCSI target server

  - by dyasny

  Hi all, I am using a RHEL server with a few hard drives, and tgtd as the iscsi target software. I a looking for a way to allocate and deallocate space and targets with that space, without restarting my system, or harming other LUNs. Currently, all my HDDs are PVs in a single VG, and I lvcreate/lvremove as required, and then export the allocated LVs using a tgt script: usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2001-04.com.lab.gss:300gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_300Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 1 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=2 --targetname iqn.2001-04.com.lab.gss:200gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 2 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_200Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 2 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=3 --targetname iqn.2001-04.com.lab.gss:100gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 3 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_100Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 3 -I ALL tgtadm --mode target --op show So in order to remove a LUN, I stop the tgtd service, lvremove the lv, and remove the entry from the iscsi target script When I add a lun, I run lvcreate, and then add an entry to the script and run it. This is not quite optimal, since restarting the service is a bad idea while other LUNs are busy, so I am looking for a more scalable and safer way. Thanks

  Read the article

• Any chance to extract Windows from recovery DVDs

  - by Pekka

  I have an Acer Tablet PC that came with WIndows XP Tablet PC Edition in the form of three recovery DVDs. Sadly, a mainboard fault put the machine out of business. I have now bought a used one from a different manufacturer that comes without an operating system. The recovery DVDs seem to contain three parts of a Norton Ghost image, and nothing else. The recovery DVD won't even start on a Non-Acer system. I'm a bit miffed because I legally own a Windows XP Tablet PC Edition license that I now can't use on the original machine any more. As far as I know, it's not legal in my jurisdiction for them to bind the license to a certain machine. I want to continue using the operating system on the new machine. Is there any chance of extracting usable Windows XP installation files from that image? How are such image files usually made up? Is there any free software around that can read Norton Ghost images so I can take a peek myself?

  Read the article

• Fast Ethernet module for Cisco 2620

  - by Kenny Rasschaert

  I have a Cisco 2620 Router. It comes with one fast ethernet port built in (circled in red), and one old AUI ethernet module is installed (circled in blue). I figure I can put a transceiver on the AUI interface to get a second RJ45 connector. What I'd really like to have is a second fast ethernet connector. The ideal candidate to achieve this would be the NM-1FE-TX module. Cisco claims on their website that this module is not suitable for the Cisco 2620 and Cisco 2620XM. It says so in "Table 2 Physical Limitation of Serial Modules per Chassis". Indeed, this module was designed for the 3600 series of routers. I've seen claims on the internet, however, of people having this module on a 2620XM, and it being fully functional. This claim gains some credibility because of the fact that in Cisco's own Packet Tracer software, you can install this module on the 2620XM router. I'm looking for a definitive answer. Will this module work on a Cisco 2620? Is there perhaps another way to get a second fast ethernet port on this device?

  Read the article

• Server Restart's and Respective Orders

  - by TheD

  EDIT:Not meaning to be disrespectful to any of the answers, but, the main question was whether rebooting a DC at the beginning of a cycle, then all the other servers, or rebooting it at the end once all the others are back online - is there a reason for doing it either way? I'm still not sure based on current responses. This will most likely seem like a fairly, maybe even stupid, question, but it's something I have been wondering about. As part of a regular process for clients servers are restarted remotely after patches and every client tends to have a similar order - but there always seems to be a small debate when it comes down to when do you reboot your DC. For example, 4 servers, 1 DC, 1xExchange, 1xBESX and 1xRandom, lets say it has some CRM software installed, is it best to reboot the DC first, then Exchange, then BESX and so on - or reboot all the servers, then reboot the DC last? - Perhaps it doesn't matter at all and it's just a case of how you have always done it. Would it change in a Hyper-V environment for example, with a physical DC, 1 VHost with all your servers virtualised on that Host? Rebooting the VHost and Virtual Machines first, then the DC at the end, or vice versa? Thanks!

  Read the article

• Spurious alleged file corruption on Windows 7

  - by Johannes Rössel

  Recently my Laptop sometimes warns about corrupted files on the hard drive (Samsung SSD PB22-JS3 TM). This has only happened so far when updating (or checking out) an SVN repository with either TortoiseSVN or the command line Subversion client. The fun thing is that the corrupted file has always been a .svn directory (although the directory entry may contain files in that directory too, if they're small enough?—?which should be the case with SVN). However, when looking into the warned-about directory I notice nothing strange or unusual and don't get any more warnings about it and another try (SVN stops updating once that error occurs?—?TortoiseSVN even with an appropriate error message) of updating the working copy works (well, mostly; sometimes it does it again, albeit with a different directory). Since the laptop is only a few months old I doubt the SSD is failing already—five months of normal usage shouldn't be too surprising. Also it (so far) occurred only with SVN updates on a large repository. Maybe that's too many writes in a short time and some part between the software and the hardware doesn't quite catch up fast enough or so?—?I don't know enough about this to actually make an informed guess here. Anyone knows what's up here? ETA: Note to add: I've run chkdsk (it seems to schedule itself anyway when this happens) and it didn't find anything out of the ordinary.

  Read the article

• Configure Windows firewall to prevent an application from listening on a specific port

  - by U-D13

  The issue: there are many applications struggling to listen on port 80 (Skype, Teamviewer et al.), and to many of them that even is not essential (in the sense that you can have a httpd running and blocking the http port, and the other application won't even squeak about being unable to open the port). What makes things worse, some of the apps are... Well, I suppose, that it's okay that the mentally impaired are being integrated in the society by giving them a job to do, but... Programming requires some intellectual effort, in my humble opinion... What I mean is that there is no way to configure the app not to use specific ports (that's what you get for using proprietary software) - you can either add it to windows firewall exceptions (and succumb to undesired port opening behavior) or not (and risk losing most - if not all - of the functionality). Technically, it is not impossible for the firewall to deny an application opening an incoming port even if the application is in the exception list. And if this functionality is built into the Windows firewall somewhere, there should be a way to activate it. So, what I want to know is: whether there exists such an option, and if it does how to activate it.

  Read the article

• Network Explorer Intermittently Fails to Display all Computers in Work Group

  - by graf_ignotiev

  I run a small computer lab of 10 computers and occasionally, when using the network explorer (a.k.a Network Browser) some or all of the remote computers will fail to appear. If I try to access a remote computer by its name I get an unspecified error (code 0x80004005), but I am still able to access it with the computer's IP address. The strangest part is that the problem will inexplicably go away after waiting awhile. Each computer is running Windows 7 x64 Enterprise and has identical hardware, software and configuration. They are all on the same subnet and in the same workgroup. I've spent days researching the problem and have tried the following solutions: Updated the BIOS, chipset and network adapter drivers Changed Power Settings in Network Adapter Properties so that the computer will not turn it off Disabled the Computer Browser service Changed the DHCP node type to broadcast Reviewed the Event Viewer logs Steps 3 and 4 have seemed to help the problem a little bit, but not completely. I'm beginning to suspect that the problem might lie with our router which is a ZyXEL ZyWALL 2WG, as the packets sent by Network Discovery may not be returning in time, but I wanted to get some perspective in the issue before I went any further.

  Read the article

• error creating MS Exchange distribution list: Active directory response: 00000005: SecErr: DSID-031521D0

  - by BabakBani

  We've migrated a client from google apps to an MS Exchange 2010 SP2 on-premise setup. The setup /prepareAD went well, and the software was installed with the Administrator account. We've used the Exchange Management Console to setup mailboxes and had to google up the appropriate workarounds such as going into each users Advanced Security Settings and selecting "include inheritable permissions from this object's parents", and changing their logon-to from specific machines to "all computers" so that they can connect to Outlook Web Access, and in turn so their Outlook 2007-2010 clients can connect to Exchange. Sending and receiving emails are working well. Now that all this is in place, we can create Dynamic Distrubution Lists with no problem, but as soon as we try and create a DISTRIBUTION LIST, either in the EMC or the Exchange PowerShell, we get an error. As the error message in the powershell is more verbose, I include this if anyone can suggest how we remedy this: [PS] C:\Windows\system32new-DistributionGroup -Name 'projects' -SamAccountName 'projects' -Alias 'projects' Active Directory operation failed on DC.cppe.local. This error is not retriable. Additional information: Access is denied. Active directory response: 00000005: SecErr: DSID-031521D0, problem 4003 (INSUFF_ACCESS_RIGHTS), data 0 + CategoryInfo : NotSpecified: (0:Int32) [New-DistributionGroup], ADOperationException + FullyQualifiedErrorId : 1EA5CD3E,Microsoft.Exchange.Management.RecipientTasks.NewDistributionGroup

  Read the article

• sudo make install: permission denied

  - by Wojtek Rzepala

  I have a most annoying question about building from sources. I've searched for an answer for a long while and nowhere can I find one... I've compiled software from sources before and this just baffled me. So I am trying to install python 2.7.2 from sources. I can do a successful ./configure, also make seems to run fine. But when I do sudo make install, I get a variety of errors... First, sudo make install gives me this: make: stat: GNUmakefile: Permission denied make: stat: makefile: Permission denied make: stat: Makefile: Permission denied make: stat: install: Permission denied make: *** No rule to make target `install'. Stop. So I did chmod +rx Makefile*. To no avail. Then, sudo ls . says ls: cannot access .: Permission denied Then ls -d . says the permissions are drwxr-x--- Then, as a desperate measure, chmod +rx .. That gave me: make: stat: Modules/config.c.in: Permission denied make: *** No rule to make target `Modules/config.c.in', needed by `Makefile'. Stop. So some progress... What is happening here? It looks like some sort of permission problem. I presumed that sudo would be the solution but clearly there is something else going on here... I tried sudo -s but I get those permission problems all over again... I am using Ubuntu 10.04LTS.

  Read the article

< Previous Page | 951 952 953 954 955 956 957 958 959 960 961 962  | Next Page >