Search Results

Search found 43235 results on 1730 pages for 'database connection'.

Page 97/1730 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

• Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

  - by Paul H

  I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

  Read the article

• Removing unused profiles from Windows network connections

  - by Shiki

  Can't figure this one out. When you connect to a wireless network (like an ad-hoc), it'll create a networkname 1 connection. After something changes, it makes a networkname 2 connection. And this goes on and on. Now I'm at connection ~23, at the home connection I'm at ~2 and ~5. Is there a way to clean these out? Couldn't find where Win stores such profiles.

  Read the article

• ssh:connection timed out

  - by user1155299

  I am trying the following command on ubuntu ssh [email protected] and I get the following error: ssh: connect to host xx.xx.xxx.xxx port 22: Connection timed out so, I tried the following: telnet xx.xx.xxx.xxx 22xx and I got the following message: Trying xx.xx.xxx.xxx... Connected to xx.xx.xxx.xxx. Escape character is '^]'. SSH-2.0-OpenSSH_5.5 Connection closed by foreign host. Can anyone help me understand what the problem is and how I can fix it.

  Read the article

• Connection make b/w iphone to windows pc-rajay [on hold]

  - by Rajay

  I Need to create connection between ios to windows by using socket programming in ios. I'm trying to to use an application to communicate with Windows via sockets. At the minimum, I'm trying to at least figure out how I can create a connection from the iPhone (maybe using the iPhone to ping the Windows machine?) I'm not really clear on where I need to start. I'm pretty new to iOS development in general, and brand new to socket/network programming. I've tried several tutorials that haven't gotten me far. My goal is: Connect to a server via sockets (the server will be a Windows machine with a service waiting for incoming connections from the iPhone) If possible, I would like to write/build the client piece first, but I have been lost thus far. Hopefully the nice folks in the SO community can lend a hand and point me in the right direction.

  Read the article

• Advantage Database Server: slow stored procedure performance.

  - by ie

  I have a question about a performance of stored procedures in the ADS. I created a simple database with the following structure: CREATE TABLE MainTable ( Id INTEGER PRIMARY KEY, Name VARCHAR(50), Value INTEGER ); CREATE UNIQUE INDEX MainTableName_UIX ON MainTable ( Name ); CREATE TABLE SubTable ( Id INTEGER PRIMARY KEY, MainId INTEGER, Name VARCHAR(50), Value INTEGER ); CREATE INDEX SubTableMainId_UIX ON SubTable ( MainId ); CREATE UNIQUE INDEX SubTableName_UIX ON SubTable ( Name ); CREATE PROCEDURE CreateItems ( MainName VARCHAR ( 20 ), SubName VARCHAR ( 20 ), MainValue INTEGER, SubValue INTEGER, MainId INTEGER OUTPUT, SubId INTEGER OUTPUT ) BEGIN DECLARE @MainName VARCHAR ( 20 ); DECLARE @SubName VARCHAR ( 20 ); DECLARE @MainValue INTEGER; DECLARE @SubValue INTEGER; DECLARE @MainId INTEGER; DECLARE @SubId INTEGER; @MainName = (SELECT MainName FROM __input); @SubName = (SELECT SubName FROM __input); @MainValue = (SELECT MainValue FROM __input); @SubValue = (SELECT SubValue FROM __input); @MainId = (SELECT MAX(Id)+1 FROM MainTable); @SubId = (SELECT MAX(Id)+1 FROM SubTable ); INSERT INTO MainTable (Id, Name, Value) VALUES (@MainId, @MainName, @MainValue); INSERT INTO SubTable (Id, Name, MainId, Value) VALUES (@SubId, @SubName, @MainId, @SubValue); INSERT INTO __output SELECT @MainId, @SubId FROM system.iota; END; CREATE PROCEDURE UpdateItems ( MainName VARCHAR ( 20 ), MainValue INTEGER, SubValue INTEGER ) BEGIN DECLARE @MainName VARCHAR ( 20 ); DECLARE @MainValue INTEGER; DECLARE @SubValue INTEGER; DECLARE @MainId INTEGER; @MainName = (SELECT MainName FROM __input); @MainValue = (SELECT MainValue FROM __input); @SubValue = (SELECT SubValue FROM __input); @MainId = (SELECT TOP 1 Id FROM MainTable WHERE Name = @MainName); UPDATE MainTable SET Value = @MainValue WHERE Id = @MainId; UPDATE SubTable SET Value = @SubValue WHERE MainId = @MainId; END; CREATE PROCEDURE SelectItems ( MainName VARCHAR ( 20 ), CalculatedValue INTEGER OUTPUT ) BEGIN DECLARE @MainName VARCHAR ( 20 ); @MainName = (SELECT MainName FROM __input); INSERT INTO __output SELECT m.Value * s.Value FROM MainTable m INNER JOIN SubTable s ON m.Id = s.MainId WHERE m.Name = @MainName; END; CREATE PROCEDURE DeleteItems ( MainName VARCHAR ( 20 ) ) BEGIN DECLARE @MainName VARCHAR ( 20 ); DECLARE @MainId INTEGER; @MainName = (SELECT MainName FROM __input); @MainId = (SELECT TOP 1 Id FROM MainTable WHERE Name = @MainName); DELETE FROM SubTable WHERE MainId = @MainId; DELETE FROM MainTable WHERE Id = @MainId; END; Actually, the problem I had - even so light stored procedures work very-very slow (about 50-150 ms) relatively to plain queries (0-5ms). To test the performance, I created a simple test (in F# using ADS ADO.NET provider): open System; open System.Data; open System.Diagnostics; open Advantage.Data.Provider; let mainName = "main name #"; let subName = "sub name #"; // INSERT let cmdTextScriptInsert = " DECLARE @MainId INTEGER; DECLARE @SubId INTEGER; @MainId = (SELECT MAX(Id)+1 FROM MainTable); @SubId = (SELECT MAX(Id)+1 FROM SubTable ); INSERT INTO MainTable (Id, Name, Value) VALUES (@MainId, :MainName, :MainValue); INSERT INTO SubTable (Id, Name, MainId, Value) VALUES (@SubId, :SubName, @MainId, :SubValue); SELECT @MainId, @SubId FROM system.iota;"; let cmdTextProcedureInsert = "CreateItems"; // UPDATE let cmdTextScriptUpdate = " DECLARE @MainId INTEGER; @MainId = (SELECT TOP 1 Id FROM MainTable WHERE Name = :MainName); UPDATE MainTable SET Value = :MainValue WHERE Id = @MainId; UPDATE SubTable SET Value = :SubValue WHERE MainId = @MainId;"; let cmdTextProcedureUpdate = "UpdateItems"; // SELECT let cmdTextScriptSelect = " SELECT m.Value * s.Value FROM MainTable m INNER JOIN SubTable s ON m.Id = s.MainId WHERE m.Name = :MainName;"; let cmdTextProcedureSelect = "SelectItems"; // DELETE let cmdTextScriptDelete = " DECLARE @MainId INTEGER; @MainId = (SELECT TOP 1 Id FROM MainTable WHERE Name = :MainName); DELETE FROM SubTable WHERE MainId = @MainId; DELETE FROM MainTable WHERE Id = @MainId;"; let cmdTextProcedureDelete = "DeleteItems"; let cnnStr = @"data source=D:\DB\test.add; ServerType=local; user id=adssys; password=***;"; let cnn = new AdsConnection(cnnStr); try cnn.Open(); let cmd = cnn.CreateCommand(); let parametrize ix prms = cmd.Parameters.Clear(); let addParam = function | "MainName" -> cmd.Parameters.Add(":MainName" , mainName + ix.ToString()) |> ignore; | "SubName" -> cmd.Parameters.Add(":SubName" , subName + ix.ToString() ) |> ignore; | "MainValue" -> cmd.Parameters.Add(":MainValue", ix * 3 ) |> ignore; | "SubValue" -> cmd.Parameters.Add(":SubValue" , ix * 7 ) |> ignore; | _ -> () prms |> List.iter addParam; let runTest testData = let (cmdType, cmdName, cmdText, cmdParams) = testData; let toPrefix cmdType cmdName = let prefix = match cmdType with | CommandType.StoredProcedure -> "Procedure-" | CommandType.Text -> "Script -" | _ -> "Unknown -" in prefix + cmdName; let stopWatch = new Stopwatch(); let runStep ix prms = parametrize ix prms; stopWatch.Start(); cmd.ExecuteNonQuery() |> ignore; stopWatch.Stop(); cmd.CommandText <- cmdText; cmd.CommandType <- cmdType; let startId = 1500; let count = 10; for id in startId .. startId+count do runStep id cmdParams; let elapsed = stopWatch.Elapsed; Console.WriteLine("Test '{0}' - total: {1}; per call: {2}ms", toPrefix cmdType cmdName, elapsed, Convert.ToInt32(elapsed.TotalMilliseconds)/count); let lst = [ (CommandType.Text, "Insert", cmdTextScriptInsert, ["MainName"; "SubName"; "MainValue"; "SubValue"]); (CommandType.Text, "Update", cmdTextScriptUpdate, ["MainName"; "MainValue"; "SubValue"]); (CommandType.Text, "Select", cmdTextScriptSelect, ["MainName"]); (CommandType.Text, "Delete", cmdTextScriptDelete, ["MainName"]) (CommandType.StoredProcedure, "Insert", cmdTextProcedureInsert, ["MainName"; "SubName"; "MainValue"; "SubValue"]); (CommandType.StoredProcedure, "Update", cmdTextProcedureUpdate, ["MainName"; "MainValue"; "SubValue"]); (CommandType.StoredProcedure, "Select", cmdTextProcedureSelect, ["MainName"]); (CommandType.StoredProcedure, "Delete", cmdTextProcedureDelete, ["MainName"])]; lst |> List.iter runTest; finally cnn.Close(); And I'm getting the following results: Test 'Script -Insert' - total: 00:00:00.0292841; per call: 2ms Test 'Script -Update' - total: 00:00:00.0056296; per call: 0ms Test 'Script -Select' - total: 00:00:00.0051738; per call: 0ms Test 'Script -Delete' - total: 00:00:00.0059258; per call: 0ms Test 'Procedure-Insert' - total: 00:00:01.2567146; per call: 125ms Test 'Procedure-Update' - total: 00:00:00.7442440; per call: 74ms Test 'Procedure-Select' - total: 00:00:00.5120446; per call: 51ms Test 'Procedure-Delete' - total: 00:00:01.0619165; per call: 106ms The situation with the remote server is much better, but still a great gap between plaqin queries and stored procedures: Test 'Script -Insert' - total: 00:00:00.0709299; per call: 7ms Test 'Script -Update' - total: 00:00:00.0161777; per call: 1ms Test 'Script -Select' - total: 00:00:00.0258113; per call: 2ms Test 'Script -Delete' - total: 00:00:00.0166242; per call: 1ms Test 'Procedure-Insert' - total: 00:00:00.5116138; per call: 51ms Test 'Procedure-Update' - total: 00:00:00.3802251; per call: 38ms Test 'Procedure-Select' - total: 00:00:00.1241245; per call: 12ms Test 'Procedure-Delete' - total: 00:00:00.4336334; per call: 43ms Is it any chance to improve the SP performance? Please advice. ADO.NET driver version - 9.10.2.9 Server version - 9.10.0.9 (ANSI - GERMAN, OEM - GERMAN) Thanks!

  Read the article

• archiving strategies and limitations of data in a table

  - by Samuel

  Environment: Jboss, Mysql, JPA, Hibernate Our web application will be catering to a large amount of users (~ 1,000,000) and there are a lots of child table where user specific data are stored (e.g. personal, health, forum contributions ...). What would be the best practice to archive user & user specific information. [a] Would it be wise to move the archived user & user specific information to their respective tables within the same database (e.g. user_archive, user_forum_comments_archive ...) OR [b] Would you just mark the database entries with a flag in the original table(s) and just query only non archived entries. We have a unique constraint on User.loginid, how do you handle this requirement if the users are archived via 1-[a] (i.e if a user with loginid 'samuel' gets moved into the archive table and if a new user gets added with the same name in the original table, how would you prevent this. What would be the best strategy to address the unique key constraints. We have a requirement to selectively archive records and bring it back if necessary, will you rely on database tools are would you handle this via your persistence APIs exposed by the JPA entity model.

  Read the article

• Are bad data issues that common?

  - by Water Cooler v2

  I've worked for clients that had a large number of distinct, small to mid-sized projects, each interacting with each other via properly defined interfaces to share data, but not reading and writing to the same database. Each had their own separate database, their own cache, their own file servers/system that they had dedicated access to, and so they never caused any problems. One of these clients is a mobile content vendor, so they're lucky in a way that they do not have to face the same problems that everyday business applications do. They can create all those separate compartments where their components happily live in isolation of the others. However, for many business applications, this is not possible. I've worked with a few clients, one of whose applications I am doing the production support for, where there are "bad data issues" on an hourly basis. Yeah, it's that crazy. Some data records from one of the instances (lower than production, of course) would have been run a couple of weeks ago, and caused some other user's data to get corrupted. And then, a data script will have to be written to fix this issue. And I've seen this happening so much with this client that I have to ask. I've seen this happening at a moderate rate with other clients, but this one just seems to be out of order. If you're working with business applications that share a large amount of data by reading and writing to/from the same database, are "bad data issues" that common in your environment?

  Read the article

• FOUR questions to ask if you are implementing DATABASE-AS-A-SERVICE

  - by Sudip Datta

  During my ongoing tenure at Oracle, I have met all types of DBAs. Happy DBAs, unhappy DBAs, proud DBAs, risk-loving DBAs, cautious DBAs. These days, as Database-as-a-Service (DBaaS) becomes more mainstream, I find some complacent DBAs who are basking in their achievement of having implemented DBaaS. Some others, however, are not that happy. They grudgingly complain that they did not have much of a say in the implementation, they simply had to follow what their cloud architects (mostly infrastructure admins) offered them. In most cases it would be a database wrapped inside a VM that would be labeled as “Database as a Service”. In other cases, it would be existing brute-force automation simply exposed in a portal. As much as I think that there is more to DBaaS than those approaches and often get tempted to propose Enterprise Manager 12c, I try to be objective. Neither do I want to dampen the spirit of the happy ones, nor do I want to stoke the pain of the unhappy ones. As I mentioned in my previous post, I don’t deny vanilla automation could be useful. I like virtualization too for what it has helped us accomplish in terms of resource management, but we need to scrutinize its merit on a case-by-case basis and apply it meaningfully. For DBAs who either claim to have implemented DBaaS or are planning to do so, I simply want to provide four key questions to ponder about: 1. Does it make life easier for your end users? Database-as-a-Service can have several types of end users. Junior DBAs, QA Engineers, Developers- each having their own skillset. The objective of DBaaS is to make their life simple, so that they can focus on their core responsibilities without having to worry about additional stuff. For example, if you are a Developer using Oracle Application Express (APEX), you want to deal with schema, objects and PL/SQL code and not with datafiles or listener configuration. If you are a QA Engineer needing database copies for functional testing, you do not want to deal with underlying operating system patching and compliance issues. The question to ask, therefore, is, whether DBaaS makes life easier for those users. It is often convenient to give them VM shells to deal with a la Amazon EC2 IaaS, but is that what they really want? Is it a productive use of a developer's time if he needs to apply RPM errata to his Linux operating system. Asking him to keep the underlying operating system current is like making a guest responsible for a restaurant's decor. 2. Does it make life easier for your administrators? Cloud, in general, is supposed to free administrators from attending to mundane tasks like provisioning services for every single end user request. It is supposed to enable a readily consumable platform and enforce standardization in the process. For example, if a Service Catalog exposes DBaaS of specific database versions and configurations, it, by its very nature, enforces certain discipline and standardization within the IT environment. What if, instead of specific database configurations, cloud allowed each end user to create databases of their liking resulting in hundreds of version and patch levels and thousands of individual databases. Therefore the right question to ask is whether the unwanted consequence of DBaaS is OS and database sprawl. And if so, who is responsible for tracking them, backing them up, administering them? Studies have shown that these administrative overheads increase exponentially with new targets, and it could result in a management nightmare. That leads us to our next question. 3. Does it satisfy your Security Officers and Compliance Auditors? Compliance Auditors need to know who did what and when. They also want the cloud platform to be secure, so that end users have little freedom in tampering with it. Dealing with VM sprawl is not the easiest of challenges, let alone dealing with them as they keep getting reconfigured and moved around. This leads to the proverbial needle in the haystack problem, and all it needs is one needle to cause a serious compliance issue in the enterprise. Bottomline is, flexibility and agility should not come at the expense of compliance and it is very important to get the balance right. Can we have security and isolation without creating compliance challenges? Instead of a ‘one size fits all approach’ i.e. OS level isolation, can we think smartly about database isolation or schema based isolation? This is where the appropriate resource modeling needs to be applied. The usual systems management vendors out there with heterogeneous common-denominator approach have compromised on these semantics. If you follow Enterprise Manager’s DBaaS solution, you will see that we have considered different models, not precluding virtualization, for different customer use cases. The judgment to use virtual assemblies versus databases on physical RAC versus Schema-as-a-Service in a single database, should be governed by the need of the applications and not by putting compliance considerations in the backburner. 4. Does it satisfy your CIO? Finally, does it satisfy your higher ups? As the sponsor of cloud initiative, the CIO is expected to lead an IT transformation project, not merely a run-of-the-mill IT operations. Simply virtualizing server resources and delivering them through self-service is a good start, but hardly transformational. CIOs may appreciate the instant benefit from server consolidation, but studies have revealed that the ROI from consolidation would flatten out at 20-25%. The question would be: what next? As we go higher up in the stack, the need to virtualize, segregate and optimize shifts to those layers that are more palpable to the business users. As Sushil Kumar noted in his blog post, " the most important thing to note here is the enterprise private cloud is not just an IT project, rather it is a business initiative to create an IT setup that is more aligned with the needs of today's dynamic and highly competitive business environment." Business users could not care less about infrastructure consolidation or virtualization - they care about business agility and service level assurance. Last but not the least, lot of CIOs get miffed if we ask them to throw away their existing hardware investments for implementing DBaaS. In Oracle, we always emphasize on freedom of choosing a platform; hence Enterprise Manager’s DBaaS solution is platform neutral. It can work on any Operating System (that the agent is certified on) Oracle’s hardware as well as 3rd party hardware. As a parting note, I urge you to remember these 4 questions. Remember that your satisfaction as an implementer lies in the satisfaction of others.

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

• 1and1 ssh - connection refused

  - by kitensei

  I'm having troubles connecting through SSH to my 1&1 account. When I try to connect with command userXXX@host -p22 -vv I have the following output: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to mySite.com [ip_here] port 22. debug1: connect to address ip_here port 22: Connection refused Moreover, once I try to connect through SSH and it fails, even the HTTP access is dead, I cannot access the website through explorer anymore :/ please help < I'm running ubuntu 11.10 EDIT: don't know if it can help, here's the .htaccess of the 1and1 server Options +Indexes Satisfy any Order Deny,Allow Allow from 212.227.X.X Deny from all RemoveType .html .gif AuthType Basic AuthName "Access to /logs" AuthUserFile /kunden/homepages/43/d376072470/htpasswd Require user "user_here" and sftp.log: Mar 26 09:21:24 193.251.X USER_HERE Connection from 193.251.X port 51809 Mar 26 09:21:30 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:39 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:41 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:45 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 09:23:57 193.251.X USER_HERE Failed password for USER_HERE from 193.251.X port 51809 ssh2 Mar 26 10:53:36 212.227.X tmp64459736-3228 Connection from 212.227.X port 23275 Mar 26 10:53:36 212.227.X tmp64459736-3228 Accepted password for tmp64459736-3228 from 212.227.X port 23275 ssh2 Mar 26 11:53:37 212.227.X tmp64459736-3228 Connection closed by 212.227.X Mar 26 18:58:17 212.227.X tmp64459736-5363 Connection from 212.227.X port 23353 Mar 26 18:58:17 212.227.X tmp64459736-5363 Accepted password for tmp64459736-5363 from 212.227.X port 23353 ssh2 Mar 26 19:53:36 212.227.X tmp64459736-8525 Connection from 212.227.X port 5166 Mar 26 19:53:36 212.227.X tmp64459736-8525 Accepted password for tmp64459736-8525 from 212.227.X port 5166 ssh2 Mar 26 19:58:17 212.227.X tmp64459736-5363 Connection closed by 212.227.X

  Read the article

• Export and import a PostgreSQL database with a different name?

  - by J. Pablo Fernández

  Is there a way to export a PostgreSQL database and later import it with another name? I'm using PostgreSQL with Rails and I often export the data from production, where the database is called blah_production and import it on development or staging with names blah_development and blah_staging. On MySQL this is trivial as the export doesn't have the database anywhere (except a comment maybe), but on PostgreSQL it seems to be impossible. Is it impossible? I've seen out there some people using sed scripts to modify the dump. I'd like to avoid that solution but if there are no alternative I'll take it. Has anybody wrote a script to alter the dump's database name ensure no data is ever altered?

  Read the article

• What are the pros of switching DNS names with a database server hardware upgrade?

  - by wilbbe01

  When we upgrade to new hardware at work we usually increment a number in the DNS name. For example. We have a server called database-2, that is slated to become database-3 in the coming days. I haven't been able to find a good reason why this is good behavior. To me the work of trying to catch all end user machines, as well as all servers dependent on the database server is far riskier than simply moving the database and ip/name with it to the new hardware. A little over a year ago we spent several months of requests coming in, as infrequent users began using software that needed to be updated to point to a new DNS name. I am struggling to find answers as to why this is a good practice. So the question. Why is using DNS names as a "server hardware version identifier" a good idea? What am I overlooking? Thanks much.

  Read the article

• Gathering statistics for an Oracle WebCenter Content Database

  - by Nicolas Montoya

  Have you ever heard: "My Oracle WebCenter Content instance is running slow. I checked the memory and CPU usage of the application server and it has plenty of resources. What could be going wrong?An Oracle WebCenter Content instance runs on an application server and relies on a database server on the back end. If your application server tier is running fine, chances are that your database server tier may host the root of the problem. While many things could cause performance problems, on active Enterprise Content Management systems, keeping database statistics updated is extremely important.The Oracle Database have a set of built-in optimizer utilities that can help make database queries more efficient. It is strongly recommended to update or re-create the statistics about the physical characteristics of a table and the associated indexes in order to maximize the efficiency of optimizers. These physical characteristics include: Number of records Number of pages Average record length The frequency with which you need to update statistics depends on how quickly the data is changing. Typically, statistics should be updated when the number of new items since the last update is greater than ten percent of the number of items when the statistics were last updated. If a large amount of documents are being added or removed from the system, the a post step should be added to gather statistics upon completion of this massive data change. In some cases, you may need to collect statistics in the middle of the data processing to expedite its execution. These proceses include but are not limited to: data migration, bootstrapping of a new system, records management disposition processing (typically at the end of the calendar year), etc. A DOCUMENTS table with a ten million rows will often generate a very different plan than a table with just a thousand.A quick check of the statistics for the WebCenter Content (WCC) Database could be performed via the below query:SELECT OWNER, TABLE_NAME, NUM_ROWS, BLOCKS, AVG_ROW_LEN,TO_CHAR(LAST_ANALYZED, 'MM/DD/YYYY HH24:MI:SS')FROM DBA_TABLESWHERE TABLE_NAME='DOCUMENTS';OWNER                          TABLE_NAME                       NUM_ROWS------------------------------ ------------------------------ ----------    BLOCKS AVG_ROW_LEN TO_CHAR(LAST_ANALYZ---------- ----------- -------------------ATEAM_OCS                      DOCUMENTS                            4172        46          61 04/06/2012 11:17:51This output will return not only the date when the WCC table DOCUMENTS was last analyzed, but also it will return the <DATABASE SCHEMA OWNER> for this table in the form of <PREFIX>_OCS.This database username could later on be used to check on other objects owned by the WCC <DATABASE SCHEMA OWNER> as shown below:SELECT OWNER, TABLE_NAME, NUM_ROWS, BLOCKS, AVG_ROW_LEN,TO_CHAR(LAST_ANALYZED, 'MM/DD/YYYY HH24:MI:SS')FROM DBA_TABLESWHERE OWNER='ATEAM_OCS'ORDER BY NUM_ROWS ASC;...OWNER                          TABLE_NAME                       NUM_ROWS------------------------------ ------------------------------ ----------    BLOCKS AVG_ROW_LEN TO_CHAR(LAST_ANALYZ---------- ----------- -------------------ATEAM_OCS                      REVISIONS                            2051        46         141 04/09/2012 22:00:22ATEAM_OCS                      DOCUMENTS                            4172        46          61 04/06/2012 11:17:51ATEAM_OCS                      ARCHIVEHISTORY                       4908       244         218 04/06/2012 11:17:49OWNER                          TABLE_NAME                       NUM_ROWS------------------------------ ------------------------------ ----------    BLOCKS AVG_ROW_LEN TO_CHAR(LAST_ANALYZ---------- ----------- -------------------ATEAM_OCS                      DOCUMENTHISTORY                      5865       110          72 04/06/2012 11:17:50ATEAM_OCS                      SCHEDULEDJOBSHISTORY                10131       244         131 04/06/2012 11:17:54ATEAM_OCS                      SCTACCESSLOG                        10204       496         268 04/06/2012 11:17:54...The Oracle Database allows to collect statistics of many different kinds as an aid to improving performance. The DBMS_STATS package is concerned with optimizer statistics only. The database sets automatic statistics collection of this kind on by default, DBMS_STATS package is intended for only specialized cases.The following subprograms gather certain classes of optimizer statistics:GATHER_DATABASE_STATS Procedures GATHER_DICTIONARY_STATS Procedure GATHER_FIXED_OBJECTS_STATS Procedure GATHER_INDEX_STATS Procedure GATHER_SCHEMA_STATS Procedures GATHER_SYSTEM_STATS Procedure GATHER_TABLE_STATS ProcedureThe DBMS_STATS.GATHER_SCHEMA_STATS PL/SQL Procedure gathers statistics for all objects in a schema.DBMS_STATS.GATHER_SCHEMA_STATS (    ownname          VARCHAR2,    estimate_percent NUMBER   DEFAULT to_estimate_percent_type                                                 (get_param('ESTIMATE_PERCENT')),    block_sample     BOOLEAN  DEFAULT FALSE,    method_opt       VARCHAR2 DEFAULT get_param('METHOD_OPT'),   degree           NUMBER   DEFAULT to_degree_type(get_param('DEGREE')),    granularity      VARCHAR2 DEFAULT GET_PARAM('GRANULARITY'),    cascade          BOOLEAN  DEFAULT to_cascade_type(get_param('CASCADE')),    stattab          VARCHAR2 DEFAULT NULL,    statid           VARCHAR2 DEFAULT NULL,    options          VARCHAR2 DEFAULT 'GATHER',    objlist          OUT      ObjectTab,   statown          VARCHAR2 DEFAULT NULL,    no_invalidate    BOOLEAN  DEFAULT to_no_invalidate_type (                                     get_param('NO_INVALIDATE')),  force             BOOLEAN DEFAULT FALSE);There are several values for the OPTIONS parameter that we need to know about: GATHER reanalyzes the whole schema     GATHER EMPTY only analyzes tables that have no existing statistics GATHER STALE only reanalyzes tables with more than 10 percent modifications (inserts, updates,   deletes) GATHER AUTO will reanalyze objects that currently have no statistics and objects with stale statistics. Using GATHER AUTO is like combining GATHER STALE and GATHER EMPTY. Example:exec dbms_stats.gather_schema_stats( -   ownname          => '<PREFIX>_OCS', -   options          => 'GATHER AUTO' -);

  Read the article

• Database Migration Scripts: Getting from place A to place B

  - by Phil Factor

  We’ll be looking at a typical database ‘migration’ script which uses an unusual technique to migrate existing ‘de-normalised’ data into a more correct form. So, the book-distribution business that uses the PUBS database has gradually grown organically, and has slipped into ‘de-normalisation’ habits. What’s this? A new column with a list of tags or ‘types’ assigned to books. Because books aren’t really in just one category, someone has ‘cured’ the mismatch between the database and the business requirements. This is fine, but it is now proving difficult for their new website that allows searches by tags. Any request for history book really has to look in the entire list of associated tags rather than the ‘Type’ field that only keeps the primary tag. We have other problems. The TypleList column has duplicates in there which will be affecting the reporting, and there is the danger of mis-spellings getting there. The reporting system can’t be persuaded to do reports based on the tags and the Database developers are complaining about the unCoddly things going on in their database. In your version of PUBS, this extra column doesn’t exist, so we’ve added it and put in 10,000 titles using SQL Data Generator. /* So how do we refactor this database? firstly, we create a table of all the tags. */IF  OBJECT_ID('TagName') IS NULL OR OBJECT_ID('TagTitle') IS NULL  BEGIN  CREATE TABLE  TagName (TagName_ID INT IDENTITY(1,1) PRIMARY KEY ,     Tag VARCHAR(20) NOT NULL UNIQUE)  /* ...and we insert into it all the tags from the list (remembering to take out any leading spaces */  INSERT INTO TagName (Tag)     SELECT DISTINCT LTRIM(x.y.value('.', 'Varchar(80)')) AS [Tag]     FROM     (SELECT  Title_ID,          CONVERT(XML, '<list><i>' + REPLACE(TypeList, ',', '</i><i>') + '</i></list>')          AS XMLkeywords          FROM   dbo.titles)g    CROSS APPLY XMLkeywords.nodes('/list/i/text()') AS x ( y )  /* we can then use this table to provide a table that relates tags to articles */  CREATE TABLE TagTitle   (TagTitle_ID INT IDENTITY(1, 1),   [title_id] [dbo].[tid] NOT NULL REFERENCES titles (Title_ID),   TagName_ID INT NOT NULL REFERENCES TagName (Tagname_ID)   CONSTRAINT [PK_TagTitle]       PRIMARY KEY CLUSTERED ([title_id] ASC, TagName_ID)       ON [PRIMARY])        CREATE NONCLUSTERED INDEX idxTagName_ID  ON  TagTitle (TagName_ID)  INCLUDE (TagTitle_ID,title_id)        /* ...and it is easy to fill this with the tags for each title ... */        INSERT INTO TagTitle (Title_ID, TagName_ID)    SELECT DISTINCT Title_ID, TagName_ID      FROM        (SELECT  Title_ID,          CONVERT(XML, '<list><i>' + REPLACE(TypeList, ',', '</i><i>') + '</i></list>')          AS XMLkeywords          FROM   dbo.titles)g    CROSS APPLY XMLkeywords.nodes('/list/i/text()') AS x ( y )    INNER JOIN TagName ON TagName.Tag=LTRIM(x.y.value('.', 'Varchar(80)'))    END    /* That's all there was to it. Now we can select all titles that have the military tag, just to try things out */SELECT Title FROM titles  INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID  INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  WHERE tagname.tag='Military'/* and see the top ten most popular tags for titles */SELECT Tag, COUNT(*) FROM titles  INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID  INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  GROUP BY Tag ORDER BY COUNT(*) DESC/* and if you still want your list of tags for each title, then here they are */SELECT title_ID, title, STUFF(  (SELECT ','+tagname.tag FROM titles thisTitle    INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID    INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  WHERE ThisTitle.title_id=titles.title_ID  FOR XML PATH(''), TYPE).value('.', 'varchar(max)')  ,1,1,'')    FROM titles  ORDER BY title_ID So we’ve refactored our PUBS database without pain. We’ve even put in a check to prevent it being re-run once the new tables are created. Here is the diagram of the new tag relationship We’ve done both the DDL to create the tables and their associated components, and the DML to put the data in them. I could have also included the script to remove the de-normalised TypeList column, but I’d do a whole lot of tests first before doing that. Yes, I’ve left out the assertion tests too, which should check the edge cases and make sure the result is what you’d expect. One thing I can’t quite figure out is how to deal with an ordered list using this simple XML-based technique. We can ensure that, if we have to produce a list of tags, we can get the primary ‘type’ to be first in the list, but what if the entire order is significant? Thank goodness it isn’t in this case. If it were, we might have to revisit a string-splitter function that returns the ordinal position of each component in the sequence. You’ll see immediately that we can create a synchronisation script for deployment from a comparison tool such as SQL Compare, to change the schema (DDL). On the other hand, no tool could do the DML to stuff the data into the new table, since there is no way that any tool will be able to work out where the data should go. We used some pretty hairy code to deal with a slightly untypical problem. We would have to do this migration by hand, and it has to go into source control as a batch. If most of your database changes are to be deployed by an automated process, then there must be a way of over-riding this part of the data synchronisation process to do this part of the process taking the part of the script that fills the tables, Checking that the tables have not already been filled, and executing it as part of the transaction. Of course, you might prefer the approach I’ve taken with the script of creating the tables in the same batch as the data conversion process, and then using the presence of the tables to prevent the script from being re-run. The problem with scripting a refactoring change to a database is that it has to work both ways. If we install the new system and then have to rollback the changes, several books may have been added, or had their tags changed, in the meantime. Yes, you have to script any rollback! These have to be mercilessly tested, and put in source control just in case of the rollback of a deployment after it has been in place for any length of time. I’ve shown you how to do this with the part of the script .. /* and if you still want your list of tags for each title, then here they are */SELECT title_ID, title, STUFF(  (SELECT ','+tagname.tag FROM titles thisTitle    INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID    INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID  WHERE ThisTitle.title_id=titles.title_ID  FOR XML PATH(''), TYPE).value('.', 'varchar(max)')  ,1,1,'')    FROM titles  ORDER BY title_ID …which would be turned into an UPDATE … FROM script. UPDATE titles SET  typelist= ThisTaglistFROM     (SELECT title_ID, title, STUFF(    (SELECT ','+tagname.tag FROM titles thisTitle      INNER JOIN TagTitle ON titles.title_ID=TagTitle.Title_ID      INNER JOIN Tagname ON Tagname.TagName_ID=TagTitle.TagName_ID    WHERE ThisTitle.title_id=titles.title_ID    ORDER BY CASE WHEN tagname.tag=titles.[type] THEN 1 ELSE 0  END DESC    FOR XML PATH(''), TYPE).value('.', 'varchar(max)')    ,1,1,'')  AS ThisTagList  FROM titles)fINNER JOIN Titles ON f.title_ID=Titles.title_ID You’ll notice that it isn’t quite a round trip because the tags are in a different order, though we’ve managed to make sure that the primary tag is the first one as originally. So, we’ve improved the database for the poor book distributors using PUBS. It is not a major deal but you’ve got to be prepared to provide a migration script that will go both forwards and backwards. Ideally, database refactoring scripts should be able to go from any version to any other. Schema synchronization scripts can do this pretty easily, but no data synchronisation scripts can deal with serious refactoring jobs without the developers being able to specify how to deal with cases like this.

  Read the article

• Oracle?????????????~????????????????????

  - by Yusuke.Yamamoto

  RDBMS ???????·????????????????????????????????????????????????????????????????????????? ????????Oracle ?????????????????????????????????? Oracle Database ???????????????????????????????? Oracle????????????? ??????????????????????????????????? ?????????????????????????????? ????????????????????????????????????????????????? ??????????????????????????????????????????????????????????????? Oracle Database ?? Compile Time ???????? ?????????SQL??????Oracle Database ????????????????????????????????????????????????????????????????? ????????????????????????????????????????????? RDBMS ???????????????????? ???????????????? Oracle Database ????????????????????????? ?????????????Oracle Database ????????????????????????????RDBMS ???????????????????????????????????????????????????????????????????????????????????????????? ??????????????????????????????????????????????? ?????????????????????????????????????????? ?????????????????????????????????????????????????? ?????????????? Oracle Database ???????????????????????? Oracle Database ????????????????????? "Oracle ????????" ?????????? Sustaining Engineering?? ?(??? ???) ???????????????? Sustaining Engineering ????????????????????????Oracle Database ???????????????????????? Oracle????????????????????????! Oracle?????????????

  Read the article

• How to use my own connection when using iBatis Data Mapper?

  - by Amitabh

  How can I use my own connection Provider when using iBatis Data Mapper? I have to use UserId and Password of the user performing the db operation in the ConnectionString? E.g. The following ConnectionString has to be modified to insert the userid and password for user performing the db operation. Data Source=TEST;Persist Security Info=True;User ID={userID};Password={password} How can this be handled in iBatis DataMapper?

  Read the article

• How to stop my network connection on WinXP using batch command?

  - by carter-boater

  for example, if I want to stop "lan connection 1" in my control pannel, I usually right click it in my control panel and disable it. Now I want to write a script to disable and enable those connections. How can I do it?? Thank you very much

  Read the article

• How to create a bash script to check the SSH connection?

  - by chutsu

  I am in the process of creating a bash script that would log into the remote machines and create private and public keys. My problem is that the remote machines are not very reliable, and they are not always up. I need a bash script that would check if the SSH connection is up. Before actually creating the keys for future use.

  Read the article

• iPhone SQLite connection in domain object - close each time?

  - by BahaiResearch.com

  I have what I would consider a small sized iPhone app that uses SQLite. There is a singleton domain object which gets data from a SQLite database. Is it better to create and open the SQLite connection for each request, or to open the DB once and hold on to it for the duration of the app. The app's reason for being is the domain object so other objects will not need the DB.

  Read the article

• Ruby, MySQL: Connection pool that is outside of the rails framework?

  - by Zombies

  Is there a ruby gem or such for MySQL connection pooling that isn't part of rails? I simply have a ruby script (again, I don't do anything with rails).

  Read the article

• How to check if internet connection is present in java?

  - by Chris

  How do you check if you can connect to the internet via java? One way would be: final URL url = new URL("http://www.google.com"); final URLConnection conn = url.openConnection(); ... if we got here, we should have net ... But is there something more appropriate to perform that task, especially if you need to do consecutive checks very often and a loss of internet connection is highly probable?

  Read the article

• Main class passes dbConn obj to all its services, I need to change the dbConn for one of its services. - suggestion for design pattern

  - by tech_learner

  There is this main class and there are several services ( which uses db connection to retrieve data ) These services are initialized in the main class db properties are obtained from the property file and then dbconnection is opened by calling a method dbOpen() written in the main class and the resultant connection object is set to the service objects by iterating through the list of services and by calling setConnection method on the service note: that the services are instantiated in the main class and the main class is not a superclass for services. I also need to mention that there is this recycle db connection scenario only main class is aware of. /** connects to DB, optionally recycling existing connection), * throws RuntimeException if unable to connect */ private void connectDb(boolean recycle) { try { if (recycle) { log.status( log.getSB().append("Recycling DB Connection") ); closeDb(); } openDb(); for ( int i = 0 ; i < service.length ; i++ ) { service[i].setConnection(db); } } One of the service needs to use a different database, what is the best design pattern to use?

  Read the article

• Dissertation about website and database security - in need of some pointers

  - by ClarkeyBoy

  Hi, I am on my dissertation in my final year at university at the moment. One of the areas I need to research is security - for both websites and for databases. I currently have sections on the following: Website Form security - such as data validation. This section is more about preventing errors made by legitimate users as much as possible rather than stopping hackers, for example comparing a field to a regular expression and giving them meaningful feedback on any errors which did occur so as to stop it happening again. Constraints. For example if a value must be true or false then use a checkbox. If it is likely to be one of several values then use a dropdown or a set of radio boxes, and so on. If the value is unpredictable then use regular expressions to limit what characters they are allowed to enter, and to restrict the length of the string, and sometimes to limit the format (such as for dates / times, post codes and so on). Sometimes you can limit permissions to the form. This is on the occasion that you know exactly who (whether it be peoples names or a group of people - such as administrators or employees) is going to need access to the form. Restricting permissions will stop members of the public from being able to access the form. Symbols or strings which could be used maliciously or cause the website to act incorrectly (such as the script tag) should be filtered out or html encoded. Captcha images can be used to prevent automated systems from filling in and submitting the form. There are some hacks for file uploads - such as using double extensions - which can allow hackers to upload malicious files. Databases (this is nowhere near done yet but the sections I have planned are listed below) SQL statements vs stored procedures Throwing an error when one of the variables contains particular characters or groups of characters (I cant remember what characters they are, but I have seen a message thrown back at me before where I have tried to enter html or something into a text area). SQL Injection - and ways around it, with some examples. Does anyone have any hints and tips on where I could go for some decent, reliable information either about these areas or about other areas of security that I could cover? Thanks in advance. Regards, Richard PS I am a complete newbie when it comes to security, so please be patient with me. If any of the information I have put down is wrong or could be sub-sectioned then please feel free to say so.

  Read the article

• Multiple database with Spring+Hibernate+JPA

  - by ziftech

  Hi everybody! I'm trying to configure Spring+Hibernate+JPA for work with two databases (MySQL and MSSQL) my datasource-context.xml: <?xml version="1.0" encoding="UTF-8"?> <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:aop="http://www.springframework.org/schema/aop" xsi:schemaLocation="http://www.springframework.org/schema/aop http://www.springframework.org/schema/aop/spring-aop-2.5.xsd http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.5.xsd http://www.springframework.org/schema/tx http://www.springframework.org/schema/tx/spring-tx-2.5.xsd http://www.springframework.org/schema/util http://www.springframework.org/schema/util/spring-util-2.5.xsd" xmlns:p="http://www.springframework.org/schema/p" xmlns:tx="http://www.springframework.org/schema/tx" xmlns:util="http://www.springframework.org/schema/util"> <!-- Data Source config --> <bean id="dataSource" class="org.apache.commons.dbcp.BasicDataSource" destroy-method="close" p:driverClassName="${local.jdbc.driver}" p:url="${local.jdbc.url}" p:username="${local.jdbc.username}" p:password="${local.jdbc.password}"> </bean> <bean id="dataSourceRemote" class="org.apache.commons.dbcp.BasicDataSource" destroy-method="close" p:driverClassName="${remote.jdbc.driver}" p:url="${remote.jdbc.url}" p:username="${remote.jdbc.username}" p:password="${remote.jdbc.password}" /> <bean id="transactionManager" class="org.springframework.orm.jpa.JpaTransactionManager" p:entity-manager-factory-ref="entityManagerFactory" /> <!-- JPA config --> <tx:annotation-driven transaction-manager="transactionManager" /> <bean id="persistenceUnitManager" class="org.springframework.orm.jpa.persistenceunit.DefaultPersistenceUnitManager"> <property name="persistenceXmlLocations"> <list value-type="java.lang.String"> <value>classpath*:config/persistence.local.xml</value> <value>classpath*:config/persistence.remote.xml</value> </list> </property> <property name="dataSources"> <map> <entry key="localDataSource" value-ref="dataSource" /> <entry key="remoteDataSource" value-ref="dataSourceRemote" /> </map> </property> <property name="defaultDataSource" ref="dataSource" /> </bean> <bean id="entityManagerFactory" class="org.springframework.orm.jpa.LocalContainerEntityManagerFactoryBean"> <property name="jpaVendorAdapter"> <bean class="org.springframework.orm.jpa.vendor.HibernateJpaVendorAdapter" p:showSql="true" p:generateDdl="true"> </bean> </property> <property name="persistenceUnitManager" ref="persistenceUnitManager" /> <property name="persistenceUnitName" value="localjpa"/> </bean> <bean class="org.springframework.orm.jpa.support.PersistenceAnnotationBeanPostProcessor" /> </beans> each persistence.xml contains one unit, like this: <persistence-unit name="remote" transaction-type="RESOURCE_LOCAL"> <properties> <property name="hibernate.ejb.naming_strategy" value="org.hibernate.cfg.DefaultNamingStrategy" /> <property name="hibernate.dialect" value="${remote.hibernate.dialect}" /> <property name="hibernate.hbm2ddl.auto" value="${remote.hibernate.hbm2ddl.auto}" /> </properties> </persistence-unit> PersistenceUnitManager cause following exception: Cannot resolve reference to bean 'persistenceUnitManager' while setting bean property 'persistenceUnitManager'; nested exception is org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'persistenceUnitManager' defined in class path resource [config/datasource-context.xml]: Initialization of bean failed; nested exception is org.springframework.beans.TypeMismatchException: Failed to convert property value of type [java.util.ArrayList] to required type [java.lang.String] for property 'persistenceXmlLocation'; nested exception is java.lang.IllegalArgumentException: Cannot convert value of type [java.util.ArrayList] to required type [java.lang.String] for property 'persistenceXmlLocation': no matching editors or conversion strategy found If left only one persistence.xml without list, every works fine but I need 2 units... I also try to find alternative solution for work with two databases in Spring+Hibernate context, so I would appreciate any solution new error after changing to persistenceXmlLocations No single default persistence unit defined in {classpath:config/persistence.local.xml, classpath:config/persistence.remote.xml} UPDATE: I add persistenceUnitName, it works, but only with one unit, still need help UPDATE: thanks, ChssPly76 I changed config files: datasource-context.xml <?xml version="1.0" encoding="UTF-8"?> <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:aop="http://www.springframework.org/schema/aop" xsi:schemaLocation="http://www.springframework.org/schema/aop http://www.springframework.org/schema/aop/spring-aop-2.5.xsd http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.5.xsd http://www.springframework.org/schema/tx http://www.springframework.org/schema/tx/spring-tx-2.5.xsd http://www.springframework.org/schema/util http://www.springframework.org/schema/util/spring-util-2.5.xsd" xmlns:p="http://www.springframework.org/schema/p" xmlns:tx="http://www.springframework.org/schema/tx" xmlns:util="http://www.springframework.org/schema/util"> <bean id="dataSource" class="org.apache.commons.dbcp.BasicDataSource" destroy-method="close" p:driverClassName="${local.jdbc.driver}" p:url="${local.jdbc.url}" p:username="${local.jdbc.username}" p:password="${local.jdbc.password}"> </bean> <bean id="dataSourceRemote" class="org.apache.commons.dbcp.BasicDataSource" destroy-method="close" p:driverClassName="${remote.jdbc.driver}" p:url="${remote.jdbc.url}" p:username="${remote.jdbc.username}" p:password="${remote.jdbc.password}"> </bean> <bean class="org.springframework.orm.jpa.support.PersistenceAnnotationBeanPostProcessor"> <property name="defaultPersistenceUnitName" value="pu1" /> </bean> <bean id="persistenceUnitManager" class="org.springframework.orm.jpa.persistenceunit.DefaultPersistenceUnitManager"> <property name="persistenceXmlLocation" value="${persistence.xml.location}" /> <property name="defaultDataSource" ref="dataSource" /> <!-- problem --> <property name="dataSources"> <map> <entry key="local" value-ref="dataSource" /> <entry key="remote" value-ref="dataSourceRemote" /> </map> </property> </bean> <bean id="entityManagerFactory" class="org.springframework.orm.jpa.LocalContainerEntityManagerFactoryBean"> <property name="jpaVendorAdapter"> <bean class="org.springframework.orm.jpa.vendor.HibernateJpaVendorAdapter" p:showSql="true" p:generateDdl="true"> </bean> </property> <property name="persistenceUnitManager" ref="persistenceUnitManager" /> <property name="persistenceUnitName" value="pu1" /> <property name="dataSource" ref="dataSource" /> </bean> <bean id="entityManagerFactoryRemote" class="org.springframework.orm.jpa.LocalContainerEntityManagerFactoryBean"> <property name="jpaVendorAdapter"> <bean class="org.springframework.orm.jpa.vendor.HibernateJpaVendorAdapter" p:showSql="true" p:generateDdl="true"> </bean> </property> <property name="persistenceUnitManager" ref="persistenceUnitManager" /> <property name="persistenceUnitName" value="pu2" /> <property name="dataSource" ref="dataSourceRemote" /> </bean> <tx:annotation-driven /> <bean id="transactionManager" class="org.springframework.orm.jpa.JpaTransactionManager" p:entity-manager-factory-ref="entityManagerFactory" /> <bean id="transactionManagerRemote" class="org.springframework.orm.jpa.JpaTransactionManager" p:entity-manager-factory-ref="entityManagerFactoryRemote" /> </beans> persistence.xml <?xml version="1.0" encoding="UTF-8"?> <persistence xmlns="http://java.sun.com/xml/ns/persistence" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/persistence http://java.sun.com/xml/ns/persistence/persistence_1_0.xsd" version="1.0"> <persistence-unit name="pu1" transaction-type="RESOURCE_LOCAL"> <properties> <property name="hibernate.ejb.naming_strategy" value="org.hibernate.cfg.DefaultNamingStrategy" /> <property name="hibernate.dialect" value="${local.hibernate.dialect}" /> <property name="hibernate.hbm2ddl.auto" value="${local.hibernate.hbm2ddl.auto}" /> </properties> </persistence-unit> <persistence-unit name="pu2" transaction-type="RESOURCE_LOCAL"> <properties> <property name="hibernate.ejb.naming_strategy" value="org.hibernate.cfg.DefaultNamingStrategy" /> <property name="hibernate.dialect" value="${remote.hibernate.dialect}" /> <property name="hibernate.hbm2ddl.auto" value="${remote.hibernate.hbm2ddl.auto}" /> </properties> </persistence-unit> </persistence> Now it builds two entityManagerFactory, but both are for Microsoft SQL Server [main] INFO org.hibernate.ejb.Ejb3Configuration - Processing PersistenceUnitInfo [ name: pu1 ...] [main] INFO org.hibernate.cfg.SettingsFactory - RDBMS: Microsoft SQL Server [main] INFO org.hibernate.ejb.Ejb3Configuration - Processing PersistenceUnitInfo [ name: pu2 ...] [main] INFO org.hibernate.cfg.SettingsFactory - RDBMS: Microsoft SQL Server (but must MySQL) I suggest, that use only dataSource, dataSourceRemote (no substitution) is not worked. That's my last problem

  Read the article

• Database design for summarized data

  - by holden

  I have a new table I'm going to add to a bunch of other summarized data, basically to take some of the load off by calculating weekly avgs. My question is whether I would be better off with one model over the other. One model with days of the week as a column with an additional column for price or another model as a series of fields for the DOW each taking a price. I'd like to know which would save me in speed and/or headaches? Or at least the trade off. IE. ID OBJECT_ID MON TUE WED THU FRI SAT SUN SOURCE OR ID OBJECT_ID DAYOFWEEK PRICE SOURCE

  Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >