configuration wizard - Page 98

What is the simplest possible configuration of Apache2 mod_proxy?

- by Eye of Hell

Hello. I have an apache2 running and i have a service available as http://www.domain.com:8080/sitename What will be a simplest apache2 configuration so entering "http://www.domain.com" in browser will show "http://www.domain.com:8080/sitename"? I have added: <VirtualHost *:80> ProxyPass / http://www.domain.com:8080/sitename/ ProxyPassReverse / http://www.domain.com:8080/sitename/ </VirtualHost> But, of course, this is not workig. Is it some simple configuration i can use for such redirect or i'm doomed to copy-paste a 100+ line configs from tutorials?

Read the article

How can I diagnose a "502 Bad Gateway" response from an Apache/Tomcat configuration?

- by Structure

I just finished up configuring a fairly default configuration of Tomcat. My Apache configuration was pre-existing and post-tomcat it still has no issues. I am using mod_jk to (if I am saying this correctly) interface between Apache and Tomcat and have my conf files setup for my workers, etc. I put my test file (Simply: http://tomcat.apache.org/tomcat-4.1-doc/appdev/sample/web/hello.jsp) into my tomcat/webapps/ directory and then call it via http://localhost/test/hello.jsp. From here Apache returns a "502 Bad Gateway" response. I confirmed this via the Apache logs, but beyond that I have no idea how to diagnose the issue. I assume the 502 is because Tomcat did not respond. I'd like to confirm if Tomcat received the request, but cannot locate the log file. At this point I had thought my installation was complete, so not sure where to go from here. Any input would be appreciated.

Read the article

How to make VLC play a .vlm configuration file in "With no interface mode"?

- by Ole Jak

How to make VLC play a VLM configuration file (.vlm) in "With no interface mode" on Windows? So I have a VLM configuration file that should stream audio from mic to localhost so no VLC user interface is needed. If I say to Windows "play VLM file with VLC" it plays correctly, starts the server where I need and streams data. But how to do such a thing manually from the command line (so we suppose we can call vlc.exe by VLC and we are now in folder with the vlc.exe and vlcConfig.vlm files)?

Read the article

Is there a way to obtain a Dell server's RAID configuration/level using only winrm/wsman? (ESXi servers)

- by EGr

I've seen videos describing how to configure RAID using wsman/winrm commands run against a server's iDRAC, but I can't seem to find anything that will just give me the current configuration and RAID levels. Is this possible? What uri would I use? If it matters, this is being run against M610s. Edit: If there is an easier way to obtain this information by running a script against the iDRAC, I'm not opposed to switching my methods. EDIT: The server is running ESXi, so if there is a way to obtain this through the vSphere client or PowerCLI, I can do that too. Overall, I just need a way to obtain the RAID configuration for multiple servers without having to query against the actual server (eg: via the iDRAC).

Read the article

Testing DNS configuration of domain by using hosts file?

- by Alex Blundell

I'm currently migrating a website to another server, and want to test the DNS configuration (more specifically, email mx records) before moving the domain over. I've configured the DNS on the new server to have mx entries for Google Apps in the same way that it's configured on the old server. The domain is controlled by nameservers on the old server at the moment, so the change would simply be updating the nameservers to the new servers. (What I'm getting at is DNS is controlled at the server level, not registrar level). Since the website has quite a number of users, I want to make sure the configuration is right before flicking the switch. For this, can I add an entry to the hosts file of my local computer to point the domain to the new server? I've done this, and the web server works, but would this also test the email mx records on the new server?

Read the article

Why has ESXi 5.0 not used the software RAID configuration on my test server?

- by kafka

I've got a test server which was running WS 2008 Enterprise on the bare metal. It was correctly using the software RAID 1 configuration (2x250 GB disks which appeared as one disk), setup on the Dell Poweredge T110 (which meets compatibility requirements) without requiring any extra setup from me. (As an aside I'm fairly sure it's software RAID, as we didn't spec a hardware RAID controller, if that's of any importance in this situation). I am now testing installing ESXi 5.0 on this server to run some VMs. I've successfully installed ESXi, and imported a VM fine, but it's showing 2 x 250 GB disks available as datastores. However they should be appearing as one volume. When I boot the server, there is a RAID configuration screen you can enter, and I'm guessing this is what I'll have to do at some stage, but now need to be very careful because there is one disk which contains data that I want to be mirrored on the other disk. What is the best thing to do in this situation?

Read the article

Is there a way to reliably backup and restore a complex network configuration on Windows XP?

- by djangofan

I have some Windows XP laptops (10+) that host a ad-hoc WIFI network connection to wireless PDA devices. The laptop itself is connected via a 3rd party VPN radio network. The radio network itself seems to be reliable. If one small thing goes wrong with the network configuration then the PDA loses connectivity and so I need a way to backup a networking config , either via a script or a 3rd party program, so that I can restore a working network configuration if something goes wrong. Is this possible? Does anyone have any ideas?

Read the article

Can different drive speeds and sizes be used in a hardware RAID configuration w/o affecting performance?

- by R. Dill

Specifically, I have a RAID 1 array configuration with two 500gb 7200rpm SATA drives mirrored as logical drive 1 (a) and two of the same mirrored as logical drive 2 (b). I'd like to add two 1tb 5400rpm drives in the same mirrored fashion as logical drive 3 (c). These drives will only serve as file storage with occasional but necessary access, and therefore, space is more important than speed. In researching whether this configuration is doable, I've been told and have read that the array will only see the smallest drive size and slowest speed. However, my understanding is that as long as the pairs themselves aren't mixed (and in this case, they aren't) that the array should view and use all drives at their actual speed and size. I'd like to be sure before purchasing the additional drives. Insight anyone?

Read the article

Automating Solaris 11 Zones Installation Using The Automated Install Server

- by Orgad Kimchi

Introduction How to use the Oracle Solaris 11 Automated install server in order to automate the Solaris 11 Zones installation. In this document I will demonstrate how to setup the Automated Install server in order to provide hands off installation process for the Global Zone and two Non Global Zones located on the same system. Architecture layout: Figure 1. Architecture layout Prerequisite Setup the Automated install server (AI) using the following instructions “How to Set Up Automated Installation Services for Oracle Solaris 11” The first step in this setup will be creating two Solaris 11 Zones configuration files. Step 1: Create the Solaris 11 Zones configuration files The Solaris Zones configuration files should be in the format of the zonecfg export command. # zonecfg -z zone1 export > /var/tmp/zone1# cat /var/tmp/zone1 create -b set brand=solaris set zonepath=/rpool/zones/zone1 set autoboot=true set ip-type=exclusive add anet set linkname=net0 set lower-link=auto set configure-allowed-address=true set link-protection=mac-nospoof set mac-address=random end Create a backup copy of this file under a different name, for example, zone2. # cp /var/tmp/zone1 /var/tmp/zone2 Modify the second configuration file with the zone2 configuration information You should change the zonepath for example: set zonepath=/rpool/zones/zone2 Step2: Copy and share the Zones configuration files Create the NFS directory for the Zones configuration files # mkdir /export/zone_config Share the directory for the Zones configuration file # share –o ro /export/zone_config Copy the Zones configuration files into the NFS shared directory # cp /var/tmp/zone1 /var/tmp/zone2 /export/zone_config Verify that the NFS share has been created using the following command # share export_zone_config /export/zone_config nfs sec=sys,ro Step 3: Add the Global Zone as client to the Install Service Use the installadm create-client command to associate client (Global Zone) with the install service To find the MAC address of a system, use the dladm command as described in the dladm(1M) man page. The following command adds the client (Global Zone) with MAC address 0:14:4f:2:a:19 to the s11x86service install service. # installadm create-client -e “0:14:4f:2:a:19" -n s11x86service You can verify the client creation using the following command # installadm list –c Service Name Client Address Arch Image Path ------------ -------------- ---- ---------- s11x86service 00:14:4F:02:0A:19 i386 /export/auto_install/s11x86service We can see the client install service name (s11x86service), MAC address (00:14:4F:02:0A:19 and Architecture (i386). Step 4: Global Zone manifest setup First, get a list of the installation services and the manifests associated with them: # installadm list -m Service Name Manifest Status ------------ -------- ------ default-i386 orig_default Default s11x86service orig_default Default Then probe the s11x86service and the default manifest associated with it. The -m switch reflects the name of the manifest associated with a service. Since we want to capture that output into a file, we redirect the output of the command as follows: # installadm export -n s11x86service -m orig_default > /var/tmp/orig_default.xml Create a backup copy of this file under a different name, for example, orig-default2.xml, and edit the copy. # cp /var/tmp/orig_default.xml /var/tmp/orig_default2.xml Use the configuration element in the AI manifest for the client system to specify non-global zones. Use the name attribute of the configuration element to specify the name of the zone. Use the source attribute to specify the location of the config file for the zone.The source location can be any http:// or file:// location that the client can access during installation. The following sample AI manifest specifies two Non-Global Zones: zone1 and zone2 You should replace the server_ip with the ip address of the NFS server. <!DOCTYPE auto_install SYSTEM "file:///usr/share/install/ai.dtd.1"> <auto_install> <ai_instance> <target> <logical> <zpool name="rpool" is_root="true"> <filesystem name="export" mountpoint="/export"/> <filesystem name="export/home"/> <be name="solaris"/> </zpool> </logical> </target> <software type="IPS"> <source> <publisher name="solaris"> <origin name="http://pkg.oracle.com/solaris/release"/> </publisher> </source> <software_data action="install"> <name>pkg:/entire@latest</name> <name>pkg:/group/system/solaris-large-server</name> </software_data> </software> <configuration type="zone" name="zone1" source="file:///net/server_ip/export/zone_config/zone1"/> <configuration type="zone" name="zone2" source="file:///net/server_ip/export/zone_config/zone2"/> </ai_instance> </auto_install> The following example adds the /var/tmp/orig_default2.xml AI manifest to the s11x86service install service # installadm create-manifest -n s11x86service -f /var/tmp/orig_default2.xml -m gzmanifest You can verify the manifest creation using the following command # installadm list -n s11x86service -m Service/Manifest Name Status Criteria --------------------- ------ -------- s11x86service orig_default Default None gzmanifest Inactive None We can see from the command output that the new manifest named gzmanifest has been created and associated with the s11x86service install service. Step 5: Non Global Zone manifest setup The AI manifest for non-global zone installation is similar to the AI manifest for installing the global zone. If you do not provide a custom AI manifest for a non-global zone, the default AI manifest for Zones is used The default AI manifest for Zones is available at /usr/share/auto_install/manifest/zone_default.xml. In this example we should use the default AI manifest for zones The following sample default AI manifest for zones # cat /usr/share/auto_install/manifest/zone_default.xml <?xml version="1.0" encoding="UTF-8"?>  <!DOCTYPE auto_install SYSTEM "file:///usr/share/install/ai.dtd.1"> <auto_install> <ai_instance name="zone_default"> <target> <logical> <zpool name="rpool">  <filesystem name="export" mountpoint="/export"/> <filesystem name="export/home"/> <be name="solaris"> <options> <option name="compression" value="on"/> </options> </be> </zpool> </logical> </target> <software type="IPS"> <destination> <image>  <facet set="false">facet.locale.*</facet> <facet set="true">facet.locale.de</facet> <facet set="true">facet.locale.de_DE</facet> <facet set="true">facet.locale.en</facet> <facet set="true">facet.locale.en_US</facet> <facet set="true">facet.locale.es</facet> <facet set="true">facet.locale.es_ES</facet> <facet set="true">facet.locale.fr</facet> <facet set="true">facet.locale.fr_FR</facet> <facet set="true">facet.locale.it</facet> <facet set="true">facet.locale.it_IT</facet> <facet set="true">facet.locale.ja</facet> <facet set="true">facet.locale.ja_*</facet> <facet set="true">facet.locale.ko</facet> <facet set="true">facet.locale.ko_*</facet> <facet set="true">facet.locale.pt</facet> <facet set="true">facet.locale.pt_BR</facet> <facet set="true">facet.locale.zh</facet> <facet set="true">facet.locale.zh_CN</facet> <facet set="true">facet.locale.zh_TW</facet> </image> </destination> <software_data action="install"> <name>pkg:/group/system/solaris-small-server</name> </software_data> </software> </ai_instance> </auto_install> (optional) We can customize the default AI manifest for Zones Create a backup copy of this file under a different name, for example, zone_default2.xml and edit the copy # cp /usr/share/auto_install/manifest/zone_default.xml /var/tmp/zone_default2.xml Edit the copy (/var/tmp/zone_default2.xml) The following example adds the /var/tmp/zone_default2.xml AI manifest to the s11x86service install service and specifies that zone1 and zone2 should use this manifest. # installadm create-manifest -n s11x86service -f /var/tmp/zone_default2.xml -m zones_manifest -c zonename="zone1 zone2" Note: Do not use the following elements or attributes in a non-global zone AI manifest: The auto_reboot attribute of the ai_instance element The http_proxy attribute of the ai_instance element The disk child element of the target element The noswap attribute of the logical element The nodump attribute of the logical element The configuration element Step 6: Global Zone profile setup We are going to create a global zone configuration profile which includes the host information for example: host name, ip address name services etc… # sysconfig create-profile –o /var/tmp/gz_profile.xml You need to provide the host information for example: Default router Root password DNS information The output should eventually disappear and be replaced by the initial screen of the System Configuration Tool (see Figure 2), where you can do the final configuration. Figure 2. Profile creation menu You can validate the profile using the following command # installadm validate -n s11x86service –P /var/tmp/gz_profile.xml Validating static profile gz_profile.xml... Passed Next, instantiate a profile with the install service. In our case, use the following syntax for doing this # installadm create-profile -n s11x86service -f /var/tmp/gz_profile.xml -p gz_profile You can verify profile creation using the following command # installadm list –n s11x86service -p Service/Profile Name Criteria -------------------- -------- s11x86service gz_profile None We can see that the gz_profie has been created and associated with the s11x86service Install service. Step 7: Setup the Solaris Zones configuration profiles The step should be similar to the Global zone profile creation on step 6 # sysconfig create-profile –o /var/tmp/zone1_profile.xml # sysconfig create-profile –o /var/tmp/zone2_profile.xml You can validate the profiles using the following command # installadm validate -n s11x86service -P /var/tmp/zone1_profile.xml Validating static profile zone1_profile.xml... Passed # installadm validate -n s11x86service -P /var/tmp/zone2_profile.xml Validating static profile zone2_profile.xml... Passed Next, associate the profiles with the install service The following example adds the zone1_profile.xml configuration profile to the s11x86service install service and specifies that zone1 should use this profile. # installadm create-profile -n s11x86service -f /var/tmp/zone1_profile.xml -p zone1_profile -c zonename=zone1 The following example adds the zone2_profile.xml configuration profile to the s11x86service install service and specifies that zone2 should use this profile. # installadm create-profile -n s11x86service -f /var/tmp/zone2_profile.xml -p zone2_profile -c zonename=zone2 You can verify the profiles creation using the following command # installadm list -n s11x86service -p Service/Profile Name Criteria -------------------- -------- s11x86service zone1_profile zonename = zone1 zone2_profile zonename = zone2 gz_profile None We can see that we have three profiles in the s11x86service install service Global Zone gz_profile zone1 zone1_profile zone2 zone2_profile. Step 8: Global Zone setup Associate the global zone client with the manifest and the profile that we create in the previous steps The following example adds the manifest and profile to the client (global zone), where: gzmanifest is the name of the manifest. gz_profile is the name of the configuration profile. mac="0:14:4f:2:a:19" is the client (global zone) mac address s11x86service is the install service name. # installadm set-criteria -m gzmanifest –p gz_profile -c mac="0:14:4f:2:a:19" -n s11x86service You can verify the manifest and profile association using the following command # installadm list -n s11x86service -p -m Service/Manifest Name Status Criteria --------------------- ------ -------- s11x86service gzmanifest mac = 00:14:4F:02:0A:19 orig_default Default None Service/Profile Name Criteria -------------------- -------- s11x86service gz_profile mac = 00:14:4F:02:0A:19 zone2_profile zonename = zone2 zone1_profile zonename = zone1 Step 9: Provision the host with the Non-Global Zones The next step is to boot the client system off the network and provision it using the Automated Install service that we just set up. First, boot the client system. Figure 3 shows the network boot attempt (when done on an x86 system): Figure 3. Network Boot Then you will be prompted by a GRUB menu, with a timer, as shown in Figure 4. The default selection (the "Text Installer and command line" option) is highlighted. Press the down arrow to highlight the second option labeled Automated Install, and then press Enter. The reason we need to do this is because we want to prevent a system from being automatically re-installed if it were to be booted from the network accidentally. Figure 4. GRUB Menu What follows is the continuation of a networked boot from the Automated Install server,. The client downloads a mini-root (a small set of files in which to successfully run the installer), identifies the location of the Automated Install manifest on the network, retrieves that manifest, and then processes it to identify the address of the IPS repository from which to obtain the desired software payload. Non-Global Zones are installed and configured on the first reboot after the Global Zone is installed. You can list all the Solaris Zones status using the following command # zoneadm list -civ Once the Zones are in running state you can login into the Zone using the following command # zlogin –z zone1 Troubleshooting Automated Installations If an installation to a client system failed, you can find the client log at /system/volatile/install_log. NOTE: Zones are not installed if any of the following errors occurs: A zone config file is not syntactically correct. A collision exists among zone names, zone paths, or delegated ZFS datasets in the set of zones to be installed Required datasets are not configured in the global zone. For more troubleshooting information see “Installing Oracle Solaris 11 Systems” Conclusion This paper demonstrated the benefits of using the Automated Install server to simplify the Non Global Zones setup, including the creation and configuration of the global zone manifest and the Solaris Zones profiles.

Read the article

web.config inheritance problem

- by abszero

Hello everyone, I am having an issue when I try and prevent inhertiance from a parent web.config down to a child specifically related to the node. My parent web.config contains about a dozen appSettings values while my child web.config contains none. Now, I originally began wrapping around only my system.net, web, etc nodes however when I ran my child application I recieved the following error: The configuration section 'appSettings' cannot be read because it is missing a section declaration I really wasn't sure what this meant and a google search didn't yield me any decent results so I attempted to move the location node to also encompass the field in my parent web.config but to no avail. My child web.config is pretty vanilla so I am not sure what the problem is. Any help you can provide would be greatly appreciated! Thanks. The child config is completely vanilla except for the addition of an Xml Namespace and a 'clear' in the config sections as follows: <configuration xmlns="http://schemas.microsoft.com/.NetConfiguration/v2.0"> <configSections> <clear /> <sectionGroup name="system.web.extensions" type="System.Web.Configuration.SystemWebExtensionsSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <sectionGroup name="scripting" type="System.Web.Configuration.ScriptingSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication"/> <sectionGroup name="webServices" type="System.Web.Configuration.ScriptingWebServicesSectionGroup, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"> <section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="Everywhere" /> <section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="roleService" type="System.Web.Configuration.ScriptingRoleServiceSection, System.Web.Extensions, Version=3.5.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35" requirePermission="false" allowDefinition="MachineToApplication" /> </sectionGroup> </sectionGroup> </sectionGroup> </configSections> The error in question is thrown at The parent web.config is far from vanilla as it is part of an Umbraco install. Here is the corrosponding section from the parent config <configuration xmlns="http://schemas.microsoft.com/.NetConfiguration/v2.0"> <configSections> <section name="urlrewritingnet" restartOnExternalChanges="true" requirePermission="false" type="UrlRewritingNet.Configuration.UrlRewriteSection, UrlRewritingNet.UrlRewriter" />  <sectionGroup name="system.web.extensions" type="System.Web.Configuration.SystemWebExtensionsSectionGroup, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"> <sectionGroup name="scripting" type="System.Web.Configuration.ScriptingSectionGroup, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"> <section name="scriptResourceHandler" type="System.Web.Configuration.ScriptingScriptResourceHandlerSection, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false" allowDefinition="MachineToApplication" /> <sectionGroup name="webServices" type="System.Web.Configuration.ScriptingWebServicesSectionGroup, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"> <section name="jsonSerialization" type="System.Web.Configuration.ScriptingJsonSerializationSection, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false" allowDefinition="Everywhere" /> <section name="profileService" type="System.Web.Configuration.ScriptingProfileServiceSection, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false" allowDefinition="MachineToApplication" /> <section name="authenticationService" type="System.Web.Configuration.ScriptingAuthenticationServiceSection, System.Web.Extensions, Version=1.0.61025.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" requirePermission="false" allowDefinition="MachineToApplication" /> </sectionGroup> </sectionGroup> </sectionGroup> <sectionGroup name="applicationSettings" type="System.Configuration.ApplicationSettingsGroup, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089"> <section name="umbraco.presentation.Properties.Settings" type="System.Configuration.ClientSettingsSection, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089" requirePermission="false" /> </sectionGroup> </configSections> The next line after the ConfigSections is: <location path="." inheritInChildApplications="false"> AppSettings, CnxStrings, System.Web, Net, WebServer settings </location>

Read the article

Running Built-In Test Simulator with SOA Suite Healthcare 11g in PS4 and PS5

- by Shub Lahiri, A-Team

Background SOA Suite for Healthcare Integration pack comes with a pre-installed simulator that can be used as an external endpoint to generate inbound and outbound HL7 traffic on specified MLLP ports. This is a command-line utility that can be very handy when trying to build a complete end-to-end demo within a standalone, closed environment. The ant-based utility accepts the name of a configuration file as the command-line input argument. The format of this configuration file has changed between PS4 and PS5. In PS4, the configuration file was XML based and in PS5, it is name-value property based. The rest of this note highlights these differences and provides samples that can be used to run the first scenario from the product samples set. PS4 - Configuration File The sample configuration file for PS4 is shown below. The configuration file contains information about the following items: Directory for incoming and outgoing files for the host running SOA Suite Healthcare Polling Interval for the directory External Endpoint Logical Names External Endpoint Server Host Name and Ports Message throughput to be simulated for generating outbound messages Documents to be handled by different endpoints A copy of this file can be downloaded from here. PS5 - Configuration File The corresponding sample configuration file for PS5 is shown below. The configuration file contains similar information about the sample scenario but is not in XML format. It has name-value pairs specified in the form of a properties file. This sample file can be downloaded from here. Simulator Configuration Before running the simulator, the environment has to be set by defining the proper ANT_HOME and JAVA_HOME. The following extract is taken from a working sample shell script to set the environment: Also, as a part of setting the environment, template jndi.properties and logging.properties can be generated by using the following ant command: ant -f ant-b2bsimulator-util.xml b2bsimulator-prop Sample jndi.properties and logging.properties are shown below and can be modified, as needed. The jndi.properties contains information about connectivity to the local Weblogic Managed Server instance and the logging.properties file controls the amount of logging that can be generated from the running simulator process. Simulator Usage - Start and Stop The command syntax to launch the simulator via ant is the same in PS4 and PS5. Only the appropriate configuration file has to be supplied as the command-line argument, for example: ant -f ant-b2bsimulator-util.xml b2bsimulatorstart -Dargs="simulator1.hl7-config.xml" This will start the simulator and will keep running to provide an active external endpoint for SOA Healthcare Integration engine. To stop the simulator, a similar ant command can be used, for example: ant -f ant-b2bsimulator-util.xml b2bsimulatorstop

Read the article

How can I get the Hibernate Configuration object from Spring?

- by Wayne Russell

Hi, I am trying to obtain Spring-defined Hibernate Configuration and SessionFactory objects in my non-Spring code. The following is the definition in my applicationContext.xml file: Code: <bean id="sessionFactory" class="org.springframework.orm.hibernate3.LocalSessionFactoryBean"> <property name="hibernateProperties"> <props> <prop key="hibernate.dialect">org.hibernate.dialect.MySQLDialect</prop> <prop key="hibernate.show_sql">true</prop> <prop key="hibernate.hbm2ddl.auto">update</prop> <prop key="hibernate.cglib.use_reflection_optimizer">true</prop> <prop key="hibernate.cache.provider_class">org.hibernate.cache.HashtableCacheProvider</prop> </props> </property> <property name="dataSource"> <ref bean="dataSource"/> </property> </bean> If I now call getBean("sessionFactory"), I am returned a $Proxy0 object which appears to be a proxy for the Hibernate SessionFactory object. But that isn't what I want - I need the LocalSessionFactoryBean itself because I need access to the Configuration as well as the SessionFactory. The reason I need the Configuration object is that our framework is able to use Hibernate's dynamic model to automatically insert mappings at runtime; this requires that we change the Configuration and rebuild the SessionFactory. Really, all we're trying to do is obtain the Hibernate config that already exists in Spring so that those of our customers that already have that information in Spring don't need to duplicate it into a hibernate.cfg.xml file in order to use our Hibernate features.

Read the article

Day 2 - Game Design Documentation

- by dapostolov

So yesterday I didn't cut any code for my game but I was able to do a tiny bit of research on the XNA Game Development Technology and the communities out there and do you know what? I feel I'm a bit closer to my goal. The bad news is today I didn't cut code either. However, not all is lost because I wanted to get my ideas on paper and today I just did that. Today, I began to jot down notes about the game and how I felt the visual elements would interact with each other. Unlike my workplace, my personal level of documentation is nothing more than a task list or a mind map of my ideas; it helps me streamline my solutions quiet effectively and circumvent the long process of articulating each thought to the n-th degree. I truly dislike documentation (because I have an extremely hard time articulating my thought and solutions); however, because I tend to do a really good job with documentation I tend to get stuck writing the buggers. But as a generalist remark: 'No Developer likes documentation.' For now let's stick with my basic notes and call this post a living document. Here are my notes, fresh, from after watching the new first episode of Merlin second season! Actually, a quick recommendation to anyone who is reading this (if anyone is): I truly recommend you envelope yourself in the medium or task you're trying to tackle. Be one with moment and feel it! For instance: Are you writing a fantasy script / game? What would the music of the genre sound like? For me the Conan the Barbarian soundtrack by Basil Poledouris is frackin awesome. There are many other good CD's out there, which I listen to (some who even use medival instruments, but Conan I keep returning to. It's a creative trigger for me. Ask yourself what would the imagery look like? Time to surf google for artist renditions of fantasy! What would the game feel like? Start playing some of your favorite games that inspire you, be wary though, have some self control and don't let it absorb your time. Anyhow, onto the documentation... Screens, Scenes, and Sprites. Oh My! (groan...) The first thing that came to mind were the screens, I thought the following would suffice: Menu Screen Character Customisation Screen Loading Screen? Battle Ground The Menu Screen Ok. So, the thought here is when the game loads a huge title is displayed: Wizard Wars. The player is prompted with 3 menu items: 1 Player Game, 2 Player Game, and Exit. Since I'm targetting the PC platform, as a non-networked game to start, I picture myself running my mouse over each menu option and the visual element of the menu item changes, along with a sound to indicate that I am over a curent menu item. And as I move my mouse away, it changes back, and possibly an exit mouse sound. Maybe on the screen somewhere is a brazier alit with a magical tome open right beside it, OR, maybe the tome is the menu! I hear the menu music as mellow, not obtrusive or piercing. On a menu item select, a confirmation sound bellows to indicate the players selection. The Esc key will always return me to the previous screens or desktop. The menu screen must feel...dark, like a really important ritual is about to happen and thus the music should build up. 1 Player Game - > Customize Character(s) 2 Player Game - > Customize Character(s) Exit - > Back to Windows Notes: So the first thing I pick up here are a couple things: First and foremost, my artistic abilities suck crap, so I may have to hire an artist (now that i've said that, lets get techy) graphical objects will be positioned within a scene on each screen / window. Menu items will be represented grapically, possibly animated, and have sound / animation effects triggered by user input or a time line. I have an animated scene involving a brazier or fire on a stick IF I was to move this game to the xbox, I'd have to track which menu item is currently selected (unless I do a mouse pointer type thing.) WindowObject has a scene A Scene has many GameObjects GameObject has a position graphic or animation MenuObject is a GameObject which has a mouse in, mouse out, and click event which either does something graphically (animation), does something with sound, or moves to another screen. Character Customisation Screen With either the 1 or 2 player option selected, both selections will come to this screen; a wizard requires a name, powers, and vestements of course! Player one will configure his character first and then player two. I considered a split screen for PC but to have two people fighting over a keyboard would probably suck. For XBox, a split screen could work; maybe when I get into the networking portion (phase 2 blog?) of this game I will remove the 2 player option for PC and provide only multiplayer and I will leave 2 player for xbox...hmm... Anyhow...I picture the creation process as follows: Name: (textbox / keyboard entry) - for xbox, this would have to be different. Robe Color: (color box, or something) Stats: Speed, Oomph, and Health. (as sliders) 1 as minimum and 10 as maximum. Ok, Back, and Cancel buttons / options. Each stat has a benefit which are listed below. The idea is the player decides if he wants his wizard to run fast, be a tank and ... hit with a purse.Regardless, the player will have a pool of 12 points to use. Ideally, A balanced wizard will have 5 in each attribute. Spells? The only spell of choice is a ball of fire which comes without question. The music and screen should still feel like a ritual. The Character Speed Basically, how fast your character moves and casts. Oomph (Best Monster Truck Voice): PURE POWAH!!! The damage output of your fireball. Health How much damage you can take. Notes: I realise the game dynamics may sound uninteresting at the moment; but I think after a couple releases, we could have some other grand ideas such as: saved profiles, gold to upgrade arsenal of spells, talents, etc...but for now...a vanilla fireball thrower mage will suffice for this experiment. OK. So... a MenuObject may need to be loosely coupled to allow future items such as networking? may be a button? a CharacterObject has a name speed oomph health and a funky robe color. cap on the three stats (1-10) an arsenal of 1 spell (possibly could expand this) The Loading Screen As is. The Battleground Screen For now, I'm keeping the screen as max resolution for the PC. The screen isn't going to move or even be a split screen. I'm not aiming high here because I want to see what level of change is involved when new features / concepts are added to game content. I'm interested to find out if we could apply techniques such as MVC or MVVM to this type of development or is it too tightly coupled? This reminds me when when my best friend and I were brainstorming our game idea (this is going back a while...1994, 6?) and he cringed at the thought of bringing business technology into games, especially when I suggested a database to store character information and COM / DCOM as the medium, but it seems I wasn't far off (reflecting); just like his implementation of a xml "config file" for dynamic direct-x menus back before .net in 1999...anyhow...i digress... The Battle One screen, two characters lobing balls of fire at each other...It doesn't get better than that. Every so often a scroll appears...and the fireballs bounce off walls, or the wizard has rapid fire, or even scrolls of healing! The scroll options are endless. Two bars at the top, each the color of the wizard (with their name beside the bar) indicate how much health they have. Possibly the appearance of the scrolls means the battle is taking too long? I'm thinking 1 player controls: up, down, left, right and space to fire the button. Or even possibly, mouse click and shift - mouse button to fire a spell in the direction they are facing. Two player controls: a, s, d, f and space AND arrows (up, down, left, right) and Del key or Crtl. The game ends when a player has 0 health and a dialog box appears asking for a rematch / reconfigure / exit. Health goes down when a fireball (friendly or not), connects with a wizard. When a wizard connects with a scroll, a countdown clock / icon appears near the health bar and the wizard begins to glow. For the most part, a wizard can have only scroll 1 effect on him at a time. Notes: Ok, there's alot to cover here. a CharacterObject is a GameObject it travels at a set velocity it travels in a direction it has sounds (walking, running, casting, impact, dying, laughing, whistling, other?) it has animations (walking, running, casting, impact, dying, laughing, idle, other?) it has a lifespan (determined by health) it is alive or dead it has a position a ScrollObject is a GameObject it carries a transferance of points "damage" (or healing, bad scroll effect?) (determinde by caster) it carries a transferance of "other" it is stationary it has a sound on impact it has a stationary animation it has an impact animation / or transfers an impact animation it has a fade animation? it has a lifespan (determined by game) it is alive or dead it has a position a WallObject is a GameObject it has a sound on fireball impact? it is a still image / stationary it has an impact animation / or transfers an impact animation it is dead it has a position A FireBall is a GameObject it carries a transferance of poinst "damage" (or healing, bad scroll effect?) (determinde by caster) it travels at a set velocity it travels in a direction it has a sound it has a travel animation it has an impact animation / or transfers an impact animation it has a fade animation? it has a lifespan (determined by caster) it is alive or dead it has a position As I look at this, I can see some common attributes in each object that I can carry up to the GameObject. I think I'm going to end the documentation here, it's taken me a bit of time to type this all out, tomorrow. I'll load up my IDE and my paint studio to get some good old fashioned cowboy hacking going! D.

Read the article

Install SharePoint 2013 on a two server farm

- by sreejukg

When SharePoint 2010 was released, I published an article on how to install SharePoint on a two server farm. You can find that article from the below link. http://weblogs.asp.net/sreejukg/archive/2010/09/28/install-sharepoint-2010-in-a-farm-environment.aspx Now it is the time for SharePoint 2013. SharePoint 2013 brings lots of improvements to the topologies, but still supports two-server architecture. Be noted that “two-server architecture” is meant for small implementations with limited service applications. Refer the below link to understand more about the SharePoint architecture http://technet.microsoft.com/en-us/sharepoint/fp123594.aspx A two tier farm consists of a database server and a web/application server as follows. In this article I am going to explain how to install SharePoint in a two server farm. I prepared 2 servers, both of them joined to a domain(SP2013Domain), and in one server I installed SQL Server 2012 (Server name: SP2013_DB). Now I am going to install SharePoint 2013 in the second server (Server Name: SP2013). The following domain accounts are created for the installation. User Account Purpose Server roles required SQLService - SQL Server service account - This account is used as the service account for SQL Server. - domain user account / local account spSetup - You will be running SharePoint setup and SharePoint products and configuration wizard using this account. -domain user account - Member of the Administrators group on each server on which Setup is run(In our case SP2013) - SQL Server login on the computer running SQL Server - Member of the Server admin SQL Server security role spDataaccess - Configure and manage server farm. This - Application pool identity for central admin website - Microsoft SharePoint Foundation Workflow Timer Service Domain user account (Other permissions will be set to this account automatically) The above are the minimum list of accounts needed for SharePoint 2013 installation. Now you need additional accounts for services, application pool identities for web applications etc. Refer the service accounts requirements for SharePoint from the below link. http://technet.microsoft.com/en-us/library/cc263445.aspx In order to install SharePoint 2013 login to the server using setup account(spsetup). Now run the setup from the installation media. First you need to install the pre-requisites. During the installation process, the server may restart several times. The installation wizard will guide you through the installation. In the next step, you need to agree on the terms and conditions as usual. Once you click next, the installation will start immediately. The installation wizard will let you know the progress of the installation. During the installation you may receive notifications to restart the server, you need to just click the finish button so that the system will be restarted. Once all the pre-requisites are installed, you will get the success message as below. Click finish to close the dialog. Now from the media, run the setup again and this time you choose install SharePoint server. In the next screen, you need to enter the product key, and then click continue. Now you need to agree on the terms and conditions for SharePoint 2013, and click continue. Choose the file location as per your policies and click on the install now button. You will see the installation progress. Once completed, you will see the installation completed dialog. Make sure you select the run products and configuration wizard option and click close. From the start screen, click next to start the configuration wizard. You will receive warning telling you some of the services will be stopped during the installation. Select “create new server farm” radio button and click next. In the next step, you need to enter the configuration database settings. Enter the database server details and then specify the database access account. You need to specify the farm account(spdataaccess). The wizard will grant additional privileges to the account as needed. In the next step you need to specify the passphrase, you need to note this as you need this passphrase if you add additional server to the farm. In the next step, you need to enter the central administration website port and security settings. You can choose a port or just keep it as suggested by the wizard. Click next, you will see the summary of what you have been selected. Verify the selected settings and if you want to change any, just click back and change them, or click continue to start the configuration. The configuration may take some time, you can view the progress, in case of any error, you will get the log file, you need to fix any error and again start the configuration wizard. Once the configuration successful, you will see the success message. Just click finish. Now you can browse the central administration website. It is good to check the health analyzer to review whether there are any errors/warnings. No warnings/errors indicate a good installation. Two-Server architecture is the least configuration for production environments. For small firms with less number of employees can implement SharePoint 2013 using this topology and as the workload increases, they can add more servers to the farm without reconstructing everything.

Read the article

Clusterware 11gR2 – Setting up an Active/Passive failover configuration

- by Gilles Haro

Oracle is providing a large range of interesting solutions to ensure High Availability of the database. Dataguard, RAC or even both configurations (as recommended by Oracle for a Maximum Available Architecture - MAA) are the most frequently found and used solutions. But, when it comes to protecting a system with an Active/Passive architecture with failover capabilities, people often thinks to other expensive third party cluster systems. Oracle Clusterware technology, which comes along at no extra-cost with Oracle Database or Oracle Unbreakable Linux, is - in the knowing of most people - often linked to Oracle RAC and therefore, is seldom used to implement failover solutions. Oracle Clusterware 11gR2 (a part of Oracle 11gR2 Grid Infrastructure) provides a comprehensive framework to setup automatic failover configurations. It is actually possible to make "failover-able'", and then to protect, almost any kind of application (from the simple xclock to the most complex Application Server). Quoting Oracle: “Oracle Clusterware is a portable cluster software that allows clustering of single servers so that they cooperate as a single system. Oracle Clusterware also provides the required infrastructure for Oracle Real Application Clusters (RAC). In addition Oracle Clusterware enables the protection of any Oracle application or any other kind of application within a cluster.” In the next couple of lines, I will try to present the different steps to achieve this goal : Have a fully operational 11gR2 database protected by automatic failover capabilities. I assume you are fluent in installing Oracle Database 11gR2, Oracle Grid Infrastructure 11gR2 on a Linux system and that ASM is not a problem for you (as I am using it as a shared storage). If not, please have a look at Oracle Documentation. As often, I made my tests using an Oracle VirtualBox environment. The scripts are tested and functional on my system. Unfortunately, there can always be a typo or a mistake. This blog entry does not replace a course around the Clusterware Framework. I just hope it will let you see how powerful it is and that it will give you the whilst to go further with it... Note : This entry has been revised (rev.2) following comments from Philip Newlan. Prerequisite 2 Linux boxes (OELCluster01 and OELCluster02) at the same OS level. I used OEL 5 Update 5 with an Enterprise Kernel. Shared Storage (SAN). On my VirtualBox system, I used Openfiler to simulate the SAN Oracle 11gR2 Database (11.2.0.1) Oracle 11gR2 Grid Infrastructure (11.2.0.1) Step 1 - Install the software Using asmlib, create 3 ASM disks (ASM_CRS, ASM_DTA and ASM_FRA) Install Grid Infrastructure for a cluster (OELCluster01 and OELCluster02 are the 2 nodes of the cluster) Use ASM_CRS to store Voting Disk and OCR. Use SCAN. Install Oracle Database Standalone binaries on both nodes. Use asmca to check/mount the disk groups on 2 nodes Use dbca to create and configure a database on the primary node Let's name it DB11G. Copy the pfile, password file to the second node. Create adump directoty on the second node. Step 2 - Setup the resource to be protected After its creation with dbca, the database is automatically protected by the Oracle Restart technology available with Grid Infrastructure. Consequently, it restarts automatically (if possible) after a crash (ex: kill -9 smon). A database resource has been created for that in the Cluster Registry. We can observe this with the command : crsctl status resource that shows and ora.dba11g.db entry. Let's save the definition of this resource, for future use : mkdir -p /crs/11.2.0/HA_scripts chown oracle:oinstall /crs/11.2.0/HA_scripts crsctl status resource ora.db11g.db -p > /crs/11.2.0/HA_scripts/myResource.txt Although very interesting, Oracle Restart is not cluster aware and cannot restart the database on any other node of the cluster. So, let's remove it from the OCR definitions, we don't need it ! srvctl stop database -d DB11G srvctl remove database -d DB11G Instead of it, we need to create a new resource of a more general type : cluster_resource. Here are the steps to achieve this : Create an action script : /crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh #!/bin/bash export ORACLE_HOME=/oracle/product/11.2.0/dbhome_1 export ORACLE_SID=DB11G case $1 in 'start') $ORACLE_HOME/bin/sqlplus /nolog <<EOF connect / as sysdba startup EOF RET=0 ;; 'stop') $ORACLE_HOME/bin/sqlplus /nolog <<EOF connect / as sysdba shutdown immediate EOF RET=0 ;; 'clean') $ORACLE_HOME/bin/sqlplus /nolog <<EOF connect / as sysdba shutdown abort ##for i in `ps -ef | grep -i $ORACLE_SID | awk '{print $2}' ` ;do kill -9 $i; done EOF RET=0 ;; 'check') ok=`ps -ef | grep smon | grep $ORACLE_SID | wc -l` if [ $ok = 0 ]; then RET=1 else RET=0 fi ;; '*') RET=0 ;; esac if [ $RET -eq 0 ]; then exit 0 else exit 1 fi This script must provide, at least, methods to start, stop, clean and check the database. It is self-explaining and contains nothing special. Just be aware that it must be runnable (+x), it runs as Oracle user (because of the ACL property - see later) and needs to know about the environment. Also make sure it exists on every node of the cluster. Moreover, as of 11.2, the clean method is mandatory. It must provide the “last gasp clean up”, for example, a shutdown abort or a kill –9 of all the remaining processes. chmod +x /crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh scp /crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh oracle@OELCluster02:/crs/11.2.0/HA_scripts Create a new resource file, based on the information we got from previous myResource.txt . Name it myNewResource.txt. myResource.txt is shown below. As we can see, it defines an ora.database.type resource, named ora.db11g.db. A lot of properties are related to this type of resource and do not need to be used for a cluster_resource. NAME=ora.db11g.db TYPE=ora.database.type ACL=owner:oracle:rwx,pgrp:oinstall:rwx,other::r-- ACTION_FAILURE_TEMPLATE= ACTION_SCRIPT= ACTIVE_PLACEMENT=1 AGENT_FILENAME=%CRS_HOME%/bin/oraagent%CRS_EXE_SUFFIX% AUTO_START=restore CARDINALITY=1 CHECK_INTERVAL=1 CHECK_TIMEOUT=600 CLUSTER_DATABASE=false DB_UNIQUE_NAME=DB11G DEFAULT_TEMPLATE=PROPERTY(RESOURCE_CLASS=database) PROPERTY(DB_UNIQUE_NAME= CONCAT(PARSE(%NAME%, ., 2), %USR_ORA_DOMAIN%, .)) ELEMENT(INSTANCE_NAME= %GEN_USR_ORA_INST_NAME%) DEGREE=1 DESCRIPTION=Oracle Database resource ENABLED=1 FAILOVER_DELAY=0 FAILURE_INTERVAL=60 FAILURE_THRESHOLD=1 GEN_AUDIT_FILE_DEST=/oracle/admin/DB11G/adump GEN_USR_ORA_INST_NAME= GEN_USR_ORA_INST_NAME@SERVERNAME(oelcluster01)=DB11G HOSTING_MEMBERS= INSTANCE_FAILOVER=0 LOAD=1 LOGGING_LEVEL=1 MANAGEMENT_POLICY=AUTOMATIC NLS_LANG= NOT_RESTARTING_TEMPLATE= OFFLINE_CHECK_INTERVAL=0 ORACLE_HOME=/oracle/product/11.2.0/dbhome_1 PLACEMENT=restricted PROFILE_CHANGE_TEMPLATE= RESTART_ATTEMPTS=2 ROLE=PRIMARY SCRIPT_TIMEOUT=60 SERVER_POOLS=ora.DB11G SPFILE=+DTA/DB11G/spfileDB11G.ora START_DEPENDENCIES=hard(ora.DTA.dg,ora.FRA.dg) weak(type:ora.listener.type,uniform:ora.ons,uniform:ora.eons) pullup(ora.DTA.dg,ora.FRA.dg) START_TIMEOUT=600 STATE_CHANGE_TEMPLATE= STOP_DEPENDENCIES=hard(intermediate:ora.asm,shutdown:ora.DTA.dg,shutdown:ora.FRA.dg) STOP_TIMEOUT=600 UPTIME_THRESHOLD=1h USR_ORA_DB_NAME=DB11G USR_ORA_DOMAIN=haroland USR_ORA_ENV= USR_ORA_FLAGS= USR_ORA_INST_NAME=DB11G USR_ORA_OPEN_MODE=open USR_ORA_OPI=false USR_ORA_STOP_MODE=immediate VERSION=11.2.0.1.0 I removed database type related entries from myResource.txt and modified some other to produce the following myNewResource.txt. Notice the NAME property that should not have the ora. prefix Notice the TYPE property that is not ora.database.type but cluster_resource. Notice the definition of ACTION_SCRIPT. Notice the HOSTING_MEMBERS that enumerates the members of the cluster (as returned by the olsnodes command). NAME=DB11G.db TYPE=cluster_resource DESCRIPTION=Oracle Database resource ACL=owner:oracle:rwx,pgrp:oinstall:rwx,other::r-- ACTION_SCRIPT=/crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh PLACEMENT=restricted ACTIVE_PLACEMENT=0 AUTO_START=restore CARDINALITY=1 CHECK_INTERVAL=10 DEGREE=1 ENABLED=1 HOSTING_MEMBERS=oelcluster01 oelcluster02 LOGGING_LEVEL=1 RESTART_ATTEMPTS=1 START_DEPENDENCIES=hard(ora.DTA.dg,ora.FRA.dg) weak(type:ora.listener.type,uniform:ora.ons,uniform:ora.eons) pullup(ora.DTA.dg,ora.FRA.dg) START_TIMEOUT=600 STOP_DEPENDENCIES=hard(intermediate:ora.asm,shutdown:ora.DTA.dg,shutdown:ora.FRA.dg) STOP_TIMEOUT=600 UPTIME_THRESHOLD=1h Register the resource. Take care of the resource type. It needs to be a cluster_resource and not a ora.database.type resource (Oracle recommendation) . crsctl add resource DB11G.db -type cluster_resource -file /crs/11.2.0/HA_scripts/myNewResource.txt Step 3 - Start the resource crsctl start resource DB11G.db This command launches the ACTION_SCRIPT with a start and a check parameter on the primary node of the cluster. Step 4 - Test this We will test the setup using 2 methods. crsctl relocate resource DB11G.db This command calls the ACTION_SCRIPT (on the two nodes) to stop the database on the active node and start it on the other node. Once done, we can revert back to the original node, but, this time we can use a more "MS$ like" method :Turn off the server on which the database is running. After short delay, you should observe that the database is relocated on node 1. Conclusion Once the software installed and the standalone database created (which is a rather common and usual task), the steps to reach the objective are quite easy : Create an executable action script on every node of the cluster. Create a resource file. Create/Register the resource with OCR using the resource file. Start the resource. This solution is a very interesting alternative to licensable third party solutions. References Clusterware 11gR2 documentation Oracle Clusterware Resource Reference Clusterware for Unbreakable Linux Using Oracle Clusterware to Protect A Single Instance Oracle Database 11gR1 (to have an idea of complexity) Oracle Clusterware on OTN Gilles Haro Technical Expert - Core Technology, Oracle Consulting

Read the article

Clusterware 11gR2 – Setting up an Active/Passive failover configuration

- by Gilles Haro

Oracle provides many interesting ways to ensure High Availability. Dataguard configurations, RAC configurations or even both (as recommended for a Maximum Available Architecture - MAA) are the most frequently found. But when it comes to protecting a system with an Active/Passive architecture with failover capabilities, one often thinks to expensive third party cluster systems. Oracle Clusterware technology, which comes free with Oracle Database, is – in the knowing of most people - often linked to Oracle RAC and therefore, is rarely used to implement failover solutions. 11gR2 Clusterware – which is part of Oracle Grid Infrastructure - provides a comprehensive framework to setup automatic failover configurations. It is actually possible to make “failover-able'” and, therefore to protect, almost every kind of application (from xclock to the more complex Application Server) In the next couple of lines, I will try to present the different steps to achieve this goal : Have a fully operational 11gR2 database protected by automatic failover capabilities. I assume you are fluent in installing Oracle Database 11gR2, Oracle Grid Infrastructure 11gR2 on a Linux system and that ASM is not a problem for you (as I am using it as a shared storage). If not, please have a look at Oracle Documentation. As often, I made my tests using an Oracle VirtualBox environment. The scripts are tested and functional. Unfortunately, there can always be a typo or a mistake. This blog entry is not a course around the Clusterware Framework. I just hope it will let you see how powerful it is and that it will give you the whilst to go further with it… Prerequisite 2 Linux boxes (OELCluster01 and OELCluster02) at the same OS level. I used OEL 5 Update 5 with Enterprise Kernel. Shared Storage (SAN). On my VirtualBox system, I used Openfiler to simulate the SAN Oracle 11gR2 Database (11.2.0.1) Oracle 11gR2 Grid Infrastructure (11.2.0.1) Step 1 – Install the software Using asmlib, create 3 ASM disks (ASM_CRS, ASM_DTA and ASM_FRA) Install Grid Infrastructure for a cluster (OELCluster01 and OELCluster02 are the 2 nodes of the cluster) Use ASM_CRS to store Voting Disk and OCR. Use SCAN. Install Oracle Database Standalone binaries on both nodes. Use asmca to check/mount the disk groups on 2 nodes Use dbca to create and configure a database on the primary node Let’s name it DB11G. Copy the pfile, password file to the second node. Create adump directoty on the second node. Step 2 - Setup the resource to be protected After its creation with dbca, the database is automatically protected by the Oracle Restart technology available with Grid Infrastructure. Consequently, it restarts automatically (if possible) after a crash (ex: kill –9 smon). A database resource has been created for that in the Cluster Registry. We can observe this with the command : crsctl status resource that shows and ora.dba11g.db entry. Let’s save the definition of this resource, for future use : mkdir –p /crs/11.2.0/HA_scripts chown oracle:oinstall /crs/11.2.0/HA_scripts crsctl status resource ora.db11g.db -p > /crs/11.2.0/HA_scripts/myResource.txt Although very interesting, Oracle Restart is not cluster aware and cannot restart the database on any other node of the cluster. So, let’s remove it from the OCR definitions, we don’t need it ! srvctl stop database -d DB11G srvctl remove database -d DB11G Instead of it, we need to create a new resource of a more general type : cluster_resource. Here are the steps to achieve this : Create an action script : /crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh #!/bin/bash export ORACLE_HOME=/oracle/product/11.2.0/dbhome_1 export ORACLE_SID=DB11G case $1 in 'start') $ORACLE_HOME/bin/sqlplus /nolog <<EOF connect / as sysdba startup EOF RET=0 ;; 'stop') $ORACLE_HOME/bin/sqlplus /nolog <<EOF connect / as sysdba shutdown immediate EOF RET=0 ;; 'check') ok=`ps -ef | grep smon | grep $ORACLE_SID | wc -l` if [ $ok = 0 ]; then RET=1 else RET=0 fi ;; '*') RET=0 ;; esac if [ $RET -eq 0 ]; then exit 0 else exit 1 fi This script must provide, at least, methods to start, stop and check the database. It is self-explaining and contains nothing special. Just be aware that it is run as Oracle user (because of the ACL property – see later) and needs to know about the environment. It also needs to be present on every node of the cluster. chmod +x /crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh scp /crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh oracle@OELCluster02:/crs/11.2.0/HA_scripts Create a new resource file, based on the information we got from previous myResource.txt . Name it myNewResource.txt. myResource.txt is shown below. As we can see, it defines an ora.database.type resource, named ora.db11g.db. A lot of properties are related to this type of resource and do not need to be used for a cluster_resource. NAME=ora.db11g.db TYPE=ora.database.type ACL=owner:oracle:rwx,pgrp:oinstall:rwx,other::r-- ACTION_FAILURE_TEMPLATE= ACTION_SCRIPT= ACTIVE_PLACEMENT=1 AGENT_FILENAME=%CRS_HOME%/bin/oraagent%CRS_EXE_SUFFIX% AUTO_START=restore CARDINALITY=1 CHECK_INTERVAL=1 CHECK_TIMEOUT=600 CLUSTER_DATABASE=false DB_UNIQUE_NAME=DB11G DEFAULT_TEMPLATE=PROPERTY(RESOURCE_CLASS=database) PROPERTY(DB_UNIQUE_NAME= CONCAT(PARSE(%NAME%, ., 2), %USR_ORA_DOMAIN%, .)) ELEMENT(INSTANCE_NAME= %GEN_USR_ORA_INST_NAME%) DEGREE=1 DESCRIPTION=Oracle Database resource ENABLED=1 FAILOVER_DELAY=0 FAILURE_INTERVAL=60 FAILURE_THRESHOLD=1 GEN_AUDIT_FILE_DEST=/oracle/admin/DB11G/adump GEN_USR_ORA_INST_NAME= GEN_USR_ORA_INST_NAME@SERVERNAME(oelcluster01)=DB11G HOSTING_MEMBERS= INSTANCE_FAILOVER=0 LOAD=1 LOGGING_LEVEL=1 MANAGEMENT_POLICY=AUTOMATIC NLS_LANG= NOT_RESTARTING_TEMPLATE= OFFLINE_CHECK_INTERVAL=0 ORACLE_HOME=/oracle/product/11.2.0/dbhome_1 PLACEMENT=restricted PROFILE_CHANGE_TEMPLATE= RESTART_ATTEMPTS=2 ROLE=PRIMARY SCRIPT_TIMEOUT=60 SERVER_POOLS=ora.DB11G SPFILE=+DTA/DB11G/spfileDB11G.ora START_DEPENDENCIES=hard(ora.DTA.dg,ora.FRA.dg) weak(type:ora.listener.type,uniform:ora.ons,uniform:ora.eons) pullup(ora.DTA.dg,ora.FRA.dg) START_TIMEOUT=600 STATE_CHANGE_TEMPLATE= STOP_DEPENDENCIES=hard(intermediate:ora.asm,shutdown:ora.DTA.dg,shutdown:ora.FRA.dg) STOP_TIMEOUT=600 UPTIME_THRESHOLD=1h USR_ORA_DB_NAME=DB11G USR_ORA_DOMAIN=haroland USR_ORA_ENV= USR_ORA_FLAGS= USR_ORA_INST_NAME=DB11G USR_ORA_OPEN_MODE=open USR_ORA_OPI=false USR_ORA_STOP_MODE=immediate VERSION=11.2.0.1.0 I removed database type related entries from myResource.txt and modified some other to produce the following myNewResource.txt. Notice the NAME property that should not have the ora. prefix Notice the TYPE property that is not ora.database.type but cluster_resource. Notice the definition of ACTION_SCRIPT. Notice the HOSTING_MEMBERS that enumerates the members of the cluster (as returned by the olsnodes command). NAME=DB11G.db TYPE=cluster_resource DESCRIPTION=Oracle Database resource ACL=owner:oracle:rwx,pgrp:oinstall:rwx,other::r-- ACTION_SCRIPT=/crs/11.2.0/HA_scripts/my_ActivePassive_Cluster.sh PLACEMENT=restricted ACTIVE_PLACEMENT=0 AUTO_START=restore CARDINALITY=1 CHECK_INTERVAL=10 DEGREE=1 ENABLED=1 HOSTING_MEMBERS=oelcluster01 oelcluster02 LOGGING_LEVEL=1 RESTART_ATTEMPTS=1 START_DEPENDENCIES=hard(ora.DTA.dg,ora.FRA.dg) weak(type:ora.listener.type,uniform:ora.ons,uniform:ora.eons) pullup(ora.DTA.dg,ora.FRA.dg) START_TIMEOUT=600 STOP_DEPENDENCIES=hard(intermediate:ora.asm,shutdown:ora.DTA.dg,shutdown:ora.FRA.dg) STOP_TIMEOUT=600 UPTIME_THRESHOLD=1h Register the resource. Take care of the resource type. It needs to be a cluster_resource and not a ora.database.type resource (Oracle recommendation) . crsctl add resource DB11G.db -type cluster_resource -file /crs/11.2.0/HA_scripts/myNewResource.txt Step 3 - Start the resource crsctl start resource DB11G.db This command launches the ACTION_SCRIPT with a start and a check parameter on the primary node of the cluster. Step 4 - Test this We will test the setup using 2 methods. crsctl relocate resource DB11G.db This command calls the ACTION_SCRIPT (on the two nodes) to stop the database on the active node and start it on the other node. Once done, we can revert back to the original node, but, this time we can use a more “MS$ like” method :Turn off the server on which the database is running. After short delay, you should observe that the database is relocated on node 1. Conclusion Once the software installed and the standalone database created (which is a rather common and usual task), the steps to reach the objective are quite easy : Create an executable action script on every node of the cluster. Create a resource file. Create/Register the resource with OCR using the resource file. Start the resource. This solution is a very interesting alternative to licensable third party solutions. References Clusterware 11gR2 documentation Oracle Clusterware Resource Reference Gilles Haro Technical Expert - Core Technology, Oracle Consulting

Read the article

When to use Constants vs. Config Files to maintain Configuration

- by CoffeeAddict

I often fight with myself on whether to put certain keys in my web.config or in a Constants.cs class or something like this. For example if I wanted to store application specific keys for whatever the case may be..I could store it and grab it from my web config via custom keys or consume it by referencing a constant in my constants class. When would you want to use Constants over config keys? This question really applies to any language I think.

Read the article

SOA Suite Integration: Part 3: Loading files

- by Anthony Shorten

One of the most common scenarios in SOA Integration is the loading of a file into the product from an external source. In Oracle SOA Suite there is a File Adapter that can process many file types into your BPEL process. For this example I will use the File Adapter to load a file of user and emails to update the user object within the Oracle Utilities Application Framework. Remember you can repeat this process with other objects and other file types. Again I am illustrating the ease of integration. The first thing is to create an empty BPEL process that will hold our flow. In Oracle JDeveloper this can be achieved by specifying the Define Service Later template (as other templates have predefined inputs and outputs and in this case we want to specify those). So I will create simpleFileLoad process to house our process. You will start with an empty canvas so you need to first specify the load part of the process using the File Adapter. Select the File Adapter from the Component Palette under BPEL Services and drag and drop it to the left side Partner Links (left is input). You name the Service. In this case I chose LoadFile. Press Next. We will define the interface as part of the wizard so select Define from operation and schema (specified later). Press Next. We are going to choose Read File to denote that we will read the file and specify the default Operation Name as Read. Press Next. The next step is to tell the Adapter the location of the files, how to process them and what to do with them after they have been processed. I am using hardcoded locations in this example but you can have logical locations as well. Press Next. I am now going to tell the adapter how to recognize the files I want to load. In my case I am using CSV files and more importantly I am tell the adapter to run the process for each record in the file it encounters. Press Next. Now, I tell the adapter how often I want to poll for the files. I have taken the defaults. Press Next. At this stage I have no explanation of the format of the input. So I am going to invoke the Native Format Wizard which will guide me through the process of creating the file input format. Clicking the purple cog icon will start the wizard. After an introduction screen (not shown), you specify the format of the input file. The File Adapter supports multiple format types. For this example, I will use Delimited as I am going to load a CSV file. Press Next. The best way for the wizard to work is with a sample. I have a sample file and the wizard will ask how much of the file to use as a template. I will use the defaults. Note: If you are using a language that has other languages other than US-ASCII, it is at this point you specify the character set to use. Press Next. The sample contains multiple instances of a single record type. The wizard supports complex types as well. We will use the appropriate setting for our file. Press Next. You have to specify the file element and the record element. This will be used by the input wizard to translate the CSV data into an XML structure (this will make sense later). I am using LoadUsers as my file delimiter (root element) and User Record as my record root element. Press Next. As the file is CSV the delimiter is "," so I will also specify that the End Of Line (EOL) indicator indicates the end of a record. Press Next. Up until this point your have not given the columns their names. In my case my sample includes the column names in the first record. This is not always the case but you can specify the names and formats of columns in this dialog (not shown). Press Next. The wizard now generates the schema for the input file. You can specify a name for the schema. I have used userupdate.xsd. We want to verify the schema so press Test. You can test the schema by specifying an input sample. and pressing the green play button. You will see the delimiters you specified earlier for the file and the records. Press Ok to continue. A confirmation screen will be displayed showing you the location of the schema in your project. Press Finish to return to the File Adapter configuration. You will now see the schema and elements prepopulated from the wizard. Press Next. The File Adapter configuration is now complete. Press Finish. Now you need to receive the input from the LoadFile component so we need to place a Receive node in the BPEL process by drag and dropping the Receive component from the Component Palette under BPEL Constructs onto the BPEL process. We link the receive process with the LoadFile component by dragging the left most connect node of the Receive node to the LoadFile component. Once the link is established you need to name the Receive node appropriately and as in the post of the last part of this series you need to generate input variables for the BPEL process to hold the input records in. You need to now add the product Web Service. The process is the same as described in the post of the last part of this series. You drop the Web Service BPEL Service onto the right side of the process and fill in the details of the WSDL URL . You also have to add an Invoke node to call the service and generate the input and outputs variables for the call in the Invoke node. Now, to get the inputs from File to the service. You have to use a Transform (you can use an Assign action but a Transform action is more flexible). You drag and drop the Transform component from the Component Palette under Oracle Extensions and place it between the Receive and Invoke nodes. We name the Transform Node, Mapper File and associate the source of the mapping the schema from the Receive node and the output will be the input variable from the Invoke node. We now build the transform. We first map the user and email attributes by drag and drop the elements from the left to the right. The reason we needed to use the transform is that we will be telling the AS-User service that we want to issue an update action. Remember when we registered the service we actually used Read as the default. If we do not otherwise inform the service to use the Update action it will use the Read action instead (which is not desired). To specify the update action you need to click on the transactionType node on the right and select Set Text to set the action. You need to specify the transactionType of UPD (for update). The mapping is now complete. The final BPEL process is ready for deployment. You then deploy the BPEL process to the server and to test the service by simply dropping a file, in the same pattern/name as you specified, in the directory you specified in the File Adapter. You will see each record as a separate instance entry in the Fusion Middleware Control console. You can now load files into the product. You can repeat this process for each type of file to process. While this was a simple example it illustrates the method of loading data can be achieved using SOA Suite in conjunction with our products.

Read the article

Routing tables don't show ppp0 after 12.04 kernel upgrade to 3.5.0: Haier CE682 modem configuration

- by ubunsteve

I'm trying to get my Haier CE682 EVDO modem, model number 201e:1022 to work in ubuntu 12.04 kernel 3.5.0-030500-generic #201207211835 . I had it working in a previous 12.04 kernel, using compat-wireless and these instructions http://zulkhamsyahmh.blogspot.com/2012/05/install-smartfren-haier-ce682-on-ubuntu.html, and to get it working had to edit the routing tables so that there was a ppp0 showing up, as suggested at http://www.linuxquestions.org/questions/slackware-14/wvdial-is-connecting-but-im-unable-to-do-anything-714861/ Network manager doesn't work with this modem, so I use either wvdial or gpppon to connect to it, both which work (after I run the command sudo modprobe usbserial vendor=0x201e product=0x1022 ) This is the output of when I connect with gpppon to the modem: Using interface ppp0 Connect: ppp0 <-- /dev/ttyUSB0 sent [LCP ConfReq id=0x1 ] rcvd [LCP ConfAck id=0x1 ] rcvd [LCP ConfReq id=0x2 ] sent [LCP ConfAck id=0x2 ] sent [LCP EchoReq id=0x0 magic=0x819c86db] rcvd [CHAP Challenge id=0x1 <1ac8f12799e953967a3cc222c9254690, name = ""] sent [CHAP Response id=0x1 <6f12a903dc40915ca2761c17b87f8fbd, name = "smart"] rcvd [LCP EchoRep id=0x0 magic=0x0] rcvd [CHAP Success id=0x1 ""] CHAP authentication succeeded CHAP authentication succeeded sent [CCP ConfReq id=0x1 ] sent [IPCP ConfReq id=0x1 ] rcvd [IPCP ConfReq id=0x1 ] sent [IPCP ConfAck id=0x1 ] rcvd [CCP ConfReq id=0x1] sent [CCP ConfAck id=0x1] rcvd [CCP ConfRej id=0x1 ] sent [CCP ConfReq id=0x2] rcvd [IPCP ConfRej id=0x1 ] sent [IPCP ConfReq id=0x2 ] rcvd [CCP ConfAck id=0x2] rcvd [IPCP ConfNak id=0x2 ] sent [IPCP ConfReq id=0x3 ] rcvd [IPCP ConfAck id=0x3 ] not replacing existing default route via 192.168.3.1 local IP address 10.191.248.154 remote IP address 10.17.95.25 primary DNS address 10.17.3.244 secondary DNS address 10.17.3.245 as you can see there is a problem with "not replacing existing default route via 192.168.3.1" This it the out put of route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.3.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.3.0 * 255.255.255.0 U 2 0 0 wlan0 I had tried these commands, which had previously worked in the earlier kernel: route del default route add default ppp0 but that broke my wireless internet connection. I then added the default routing as shown above with sudo route add default gw 192.168.3.1 wlan0 So it seems I need to add or change the routing to show a ppp0 connection, but I don't know how to do that.

Read the article

Why does my RAID configuration with mdadm fail on reboots?

- by Andy B

I have been running Ubuntu server on my machine for 2 years and it has worked ok. I would like to speed it up by raiding a few drives. The machine is used to host my Mysql databases internally. using MDADM raid.. I have tried 2 schemes so far with the 3 drives. 2 partitions on each drive 1 for the swap 1 for the O/S both of them turned into drives raid level 5 3 partitions on each drive 1 for the boot 1 for the swap and 1 for the root. The boot I set to raid level1 and the swap and root raid drives were set to level5 Both setup worked fine for about a week, then on a reboot things fall apart. by fall apart I mean I end up with a bunch of hard drive errors on the screen and then get a grub prompt. Why do they fail on reboots? I am eager to understand what I am doing wrong thanks!

Read the article

How can IIS 7.5 have the error pages for a site reset to the default configuration?

- by Sn3akyP3t3

A mishap occurred with web.config to accommodate a subsite existing. I made use of “<location path="." inheritInChildApplications="false">”. Essentially it was a workaround put in place for nested web.config files which was causing a conflict. The result was that error pages were not being handled properly. Error 500 was being passed to the client for every type of error encountered. Removal of the offending inheritInChildApplications tag from the root web.config restored normal operations of most of the error handling, but for some reason error 503 is a correct response header, but the IIS server is performing the custom actions for error 403.4 which is a redirect to https. I'm looking to restore defaults for error pages so that the behavior once again is restored. I then can re-add customizations for the error pages.

Read the article

E-Business Suite Applications Technology Group (ATG) Advisor Webcast Program – June 2014

- by LuciaC-Oracle

Webcast: EBS Patch Wizard Overview Date: Thursday June 12, 2014 at 18:00 UK / 10:00 PST / 11:00 MST / 13:00 EST Topics covered will include: What is Oracle EBS Patch Wizard Tool? Benefits of the Patch Wizard utility Patch Wizard Interface Patch Impact Analysis Details & Registration : Doc ID 1672371.1Direct registration link. Webcast: EBS Proactive Analyzers Overview Date: Thursday June 26, 2014 at 18:00 UK / 10:00 PST / 11:00 MST / 13:00 EST Topics covered will include: What are Oracle Support Analyzers? How to identify the Analyzers available? Short Analyzers Overview Patch Impact Analysis How to use an Analyzer? Details & Registration : Doc ID 1672363.1Direct registration link.If you have any questions about the schedules or if you have a suggestion for an Advisor Webcast to be planned in future, please send an E-Mail to Ruediger Ziegler.

Read the article

How to remove all associated files and configuration settings of an app installed through 'force architecture' command

- by Mysterio

A few weeks ago I installed a 32 bit .deb file through the 'force architecture' command (on my 64bit notebook), however the procedure was unsuccessful and I used the apt-get purgecommand to uninstall the app. It seems there are some leftovers of the app I uninstalled which has now broken system update. Synaptic recommended a sudo apt-get install -fwhich I did in the terminal with this initial response: Reading package lists... Done Building dependency tree Reading state information... Done The following package was automatically installed and is no longer required: libntfs10 Use 'apt-get autoremove' to remove them. The following packages will be REMOVED: crossplatformui 0 upgraded, 0 newly installed, 1 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? I chose 'Y' then got this response: (Reading database ... 187616 files and directories currently installed.) Removing crossplatformui ... ztemtvcdromd: no process found dpkg: error processing crossplatformui (--remove): subprocess installed post-removal script returned error exit status 1 Errors were encountered while processing: crossplatformui E: Sub-process /usr/bin/dpkg returned an error code (1) It seems the app I installed crossplatformuiis still on my system and has caused update manager to stop running with a partial upgrade warning. What do I do now?

Read the article

How to configure screens in console or create screen configuration profiles?

- by uncle Lem

I have two monitors and integrated GPU (Intel® HD Graphics 4600). It works fine for work or movies, but if I launch games in fullscreen mode - I get artifacts, glitches and so on. Temporary disabling second monitor solve this problem, but then I have to enable it back, and set its properties manually (by default, additional screen attaches its left-top corner to main monitor's right-top corner, but I need it to be left-bottom and right-bottom corners). So I need some kind of automatization here. Best option - tool to create and swap between some kind of config profiles. Or, maybe, some console manipulations which I can put into script files would be fine too. (Ubuntu 13.04, if it matters)

Search Results

Search found 16321 results on 653 pages for 'configuration wizard'.

Page 98/653 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105 | Next Page >

- by Eye of Hell

- by Structure

- by Ole Jak

- by EGr

- by Alex Blundell

- by kafka

- by djangofan

- by R. Dill

- by Orgad Kimchi

- by abszero

- by Shub Lahiri, A-Team

- by Wayne Russell

- by dapostolov

- by sreejukg

- by Gilles Haro

- by Gilles Haro

- by CoffeeAddict

- by Anthony Shorten

- by ubunsteve

- by Andy B

- by Sn3akyP3t3

- by LuciaC-Oracle

- by Mysterio

- by uncle Lem

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105 | Next Page >