Search Results

Search found 14 results on 1 pages for 'wfaulk'.

Page 1/1 | 1 

  • Large virtual memory size of ElasticSearch JVM

    - by wfaulk
    I am running a JVM to support ElasticSearch. I am still working on sizing and tuning, so I left the JVM's max heap size at ElasticSearch's default of 1GB. After putting data in the database, I find that the JVM's process is showing 50GB in SIZE in top output. It appears that this is actually causing performance problems on the system; other processes are having trouble allocating memory. In asking the ElasticSearch community, they suggested that it's "just" filesystem caching. In my experience, filesystem caching doesn't show up as memory used by a particular process. Of course, they may have been talking about something other than the OS's filesystem cache, maybe something that the JVM or ElasticSearch itself is doing on top of the OS. But they also said that it would be released if needed, and that didn't seem to be happening. So can anyone help me figure out how to tune the JVM, or maybe ElasticSearch itself, to not use so much RAM. System is Solaris 10 x86 with 72GB RAM. JVM is "Java(TM) SE Runtime Environment (build 1.7.0_45-b18)".

    Read the article

  • Cannot join Win7 workstations to Win2k8 domain

    - by wfaulk
    I am trying to connect a Windows 7 Ultimate machine to a Windows 2k8 domain and it's not working. I get this error: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "example.local": The query was for the SRV record for _ldap._tcp.dc._msdcs.example.local The following domain controllers were identified by the query: dc1.example.local dc2.example.local However no domain controllers could be contacted. Common causes of this error include: Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. Domain controllers registered in DNS are not connected to the network or are not running. The client is in an office connected remotely via MPLS to the data center where our domain controllers exist. I don't seem to have anything blocking connectivity to the DCs, but I don't have total control over the MPLS circuit, so it's possible that there's something blocking connectivity. I have tried multiple clients (Win7 Ultimate and WinXP SP3) in the one office and get the same symptoms on all of them. I have no trouble connecting to either of the domain controllers, though I have, admittedly, not tried every possible port. ICMP, LDAP, DNS, and SMB connections all work fine. Client DNS is pointing to the DCs, and "example.local" resolves to the two IP addresses of the DCs. I get this output from the NetLogon Test command line utility: C:\Windows\System32>nltest /dsgetdc:example.local Getting DC name failed: Status = 1355 0x54b ERROR_NO_SUCH_DOMAIN I have also created a separate network to emulate that office's configuration that's connected to the DC network via LAN-to-LAN VPN instead of MPLS. Joining Windows 7 computers from that remote network works fine. The only difference I can find between the two environments is the intermediate connectivity, but I'm out of ideas as to what to test or how to do it. What further steps should I take? (Note that this isn't actually my client workstation and I have no direct access to it; I'm forced to do remote hands access to it, which makes some of the obvious troubleshooting methods, like packet sniffing, more difficult. If I could just set up a system there that I could remote into, I would, but requests to that effect have gone unanswered.) 2011-08-25 update: I had DCDIAG.EXE run on a client attempting to join the domain: C:\Windows\System32>dcdiag /u:example\adminuser /p:********* /s:dc2.example.local Directory Server Diagnosis Performing initial setup: Ldap search capabality attribute search failed on server dc2.example.local, return value = 81 This sounds like it was able to connect via LDAP, but the thing that it was trying to do failed. But I don't quite follow what it was trying to do, much less how to reproduce it or resolve it. 2011-08-26 update: Using LDP.EXE to try and make an LDAP connection directly to the DCs results in these errors: ld = ldap_open("10.0.0.1", 389); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 389); Error <0x51: Fail to connect to 10.0.0.2. ld = ldap_open("10.0.0.1", 3268); Error <0x51: Fail to connect to 10.0.0.1. ld = ldap_open("10.0.0.2", 3268); Error <0x51: Fail to connect to 10.0.0.2. This would seem to point fingers at LDAP connections being blocked somewhere. (And 0x51 == 81, which was the error from DCDIAG.EXE from yesterday's update.) I could swear I tested this using TELNET.EXE weeks ago, but now I'm thinking that I may have assumed that its clearing of the screen was telling me that it was waiting and not that it had connected. I'm tracking down LDAP connectivity problems now. This update may become an answer.

    Read the article

  • NetApp FAS270 head doesn't see disks

    - by wfaulk
    I have an FAS270C. For months, I've been running it in a split-head manner (that is, with each head serving data totally independently, and without any clustering even being enabled) in order to facilitate moving some data around. I finally got everything situated, moved all the data to one of the heads, and was trying to get clustering set back up. Now when I try to install OnTap onto the "new" head, it cannot see any of the disks in the head shelf. (That is, the shelf into which the heads are inserted.) I've booted into maintenance mode, and it shows me that the 0b adapter, which should be the adapter that that shelf and its disks should be presented on, is in "OFFLINE (physical)" state. If I try to enable it with either "storage enable adapter 0b" or "fcadmin online 0b", it waits for about 30 seconds and then says: [fci.initialization.failed:error]: Initialization failed on Fibre Channel adapter 0b. [fci.adapter.online.failed:error]: Fibre Channel adapter 0b failed to come online. There is currently nothing attached to its external 0b port. I've tried it with and without an SFP plugged into it, and with and without its internal termination switch on. The currently active head can see those disks, and can see that two of them are assigned to the other head. Before I started reconfiguring, the "new" head could see disks on that shelf. They may even be the same disks that OnTap was installed on previously. Does anyone have any idea how to proceed?

    Read the article

  • IDE/PATA high-speed hard drive dock

    - by wfaulk
    I frequently need to access bare drives for backups and need a quick, high-speed way to deal with them. There are a multitude of SATA hard drive docks (for example), but I have a lot of IDE/PATA (hereafter "IDE") drives that I would like to be able to use similarly. There are IDE-to-SATA adapters so you can plug your IDE hard drive into a SATA port, so I don't see any reason why you couldn't use the same technology to have a native dock, yet none seems to exist. Now, I'm aware that 3.5" IDE drives do not have a specification for the layout of the connector, and therefore can't be slapped into a dock the same way a SATA drive could, but 2.5" PATA drives do. In fact, I'm not terribly interested in supporting 3.5" drives. It would be nice, but I deal with them far less frequently than 2.5" drives. Also, I'd very much like for the connection to the computer be faster than USB, preferably eSATA, I don't want to be spending time mounting a drive inside an enclosure, I don't want bare drives lying around with a cable hanging off of them, and I'd prefer a single dock rather than two. What seems like the ideal solution to me would be a regular SATA→eSATA dock and some sort of screwless adapter for IDE drives, but I'm open to any suggestions, regardless of my stated preferences, but which are, in some sort of order of preference: high-speed (faster than USB, at least) holder for drive (not just a cable) no complicated enclosure support for 3.5" IDE drives single dock Updates: Here's a 3.5" IDE to 3.5" SATA docking adapter that could be part of the solution. Weird. I figured that would be the impossible part. I was hoping to find something like this 2.5" to 3.5" SATA chassis that would take a 44-pin IDE drive internally. It looks like the Vantec EZ Swap EX comes awfully close. It has its own bay dock, but it looks like the SATA ports on the back are spaced properly, even if they're not aligned quite properly. Unfortunately, the proper position is at the very edge of the drive, which means that the docks' connectors are at the very edge of their recesses, which means there's no way to fit it in there.

    Read the article

  • NetBackup prefers "Scratch" tapes over dedicated tapes

    - by wfaulk
    I have a NetBackup 6.0MP7 installation running on Windows Server 2003. It functions as the only Master Server and Media Server. I swap a full set of tapes in and out every week, but leave a set of tapes with their Volume Pool set to "Scratch" in all the time. The weekly tape sets then get rotated back in after a period of time. Largely, this works fine. I seldom actually need the scratch tapes, but every once in a while, a backup will run over what I have dedicated to the task. However, one week's set of tapes consistently gets declined in favor of the scratch pool. The backup policies are the same for every week, they all have "Policy Volume Pool" set to "NetBackup", and all of the tapes for every week (beside the scratch tapes) have had their pools assigned as "NetBackup", definitely including the week that always gets ignored. That said, it doesn't ignore all of the NetBackup pool tapes for that week. It does usually write to two or three of them, but it writes to like 20 of the scratch tapes. (I haven't thought to look to see if it's always the same two or three tapes.) And this problem never seems to occur for any other week. It doesn't load the tapes and then reject them; it never seems to try to use them at all. They are not flagged as frozen. They are all active and unassigned when I swap them in. The tapes are in a Quantum PX510 tape library. The NetBackup server is attached to the library/robot via fibrechannel going through an HP-branded Brocade switch. I'm not an expert on NetBackup at all. I don't really even know where to look. Any advice on logs to look at or logging to enable or really anything at all would be appreciated. I'll keep an eye on the question and update it if anyone needs any more info to help.

    Read the article

  • Spanning-tree setup with incompatible switches

    - by wfaulk
    I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

    Read the article

  • Cannot uninstall XP SP3 update

    - by wfaulk
    I need to uninstall Service Pack 3 because it broke a program I rely on (FrameMaker). I have done this before on other computers using Microsoft's SP3 uninstall instructions. However, on this computer, SP3 is not listed in Add/Remove Programs (and, yes, I have checked the "Show Updates" checkbox), there's no "$NtServicePackUninstall$" restore directory, and either Windows didn't create a restore point for the SP3 install or it has fallen off of the list of restorable points. Does anyone know of any other options?

    Read the article

  • Windows 2008 R2: can't extend C drive, mystery partitions

    - by wfaulk
    I have a Windows 2008 R2 server running under VMware ESX 4.0.0. I have reallocated disk space to it in order to extend the C drive, but Disk Management has "Extend Volume" greyed out. DISKPART shows more partitions than Disk Management shows, including one after the volume I'm trying to extend, which would explain why Disk Management isn't allowing the extension. Disk Management shows: System Reserved / 100MB NTFS / Healthy (System) (C:) / 39.39 GB NTFS / Healthy (Boot, Page File, Crash Dump) 10.00 GB / Unallocated DISKPART shows: Partition 1 Dynamic Data 992 KB 31 KB Partition 2 Dynamic Data 100 MB 1024 KB Partition 3 Dynamic Data 39 GB 101 MB Partition 4 Dynamic Data 1024 KB 39 GB My question at this point is: what the heck are partitions 1 and 4, where did they come from, why doesn't Disk Management show them, and, most importantly, can I delete partition 4 in order to extend partition 3?

    Read the article

  • Outlook refuses to connect to Exchange

    - by wfaulk
    Outlook 2007 under Windows XP connecting to Exchange 2003 SP2: when started, it flips back and forth between "Connecting to Exchange Server" and "Disconnected" three or four times, then gives up and stays disconnected. I tried deleting the ost file (which was nearly 2GB), turning Cached mode on and off, recreating the account inside the Mail control panel, changing the account to use HTTP, and probably some other things. None of it seemed to make any difference, until … After fiddling with it for a while, I got this absurd error message dialog at startup, and it exits after I click OK: Cannot start Microsoft Office Outlook. Cannot open the Outlook window. The set of folders cannot be opened. Microsoft Exchange is not available. Either there are network problems or the Exchange server is down for maintenance. (I'm not sure if I can even trust that message. It's so long, it just feels like a random offset into Outlook's stack of error messages.) Either way, the Exchange server is available to everyone else, and is available via OWA from that computer. I ran Process Explorer against Outlook and it showed 5 or so ESTABLISHED connections to our Exchange server, plus listening on two UDP ports, and two CLOSE_WAIT connections to localhost. If I managed to look at Outlook's IP connections while it was doing its Connecting/Disconnected dance, it had a huge number of connections open to the Exchange server. It more than filled ProcExp's dialog box; I'm guessing at least 20, probably more. The only other odd thing is that our network admin at some point added a wildcard DNS record to the domain name that we use for email, and now Outlook will sometimes (always?) start by complaining about autodiscover.example.com's SSL certificate. There is a web server there, but it doesn't have any sort of email autodiscover anything on it. It doesn't make any difference if I click "OK" or "Cancel" (or whatever the buttons are). I also added a bogus entry for the hostname to Windows' hosts file, pointing it at 127.0.0.2, and it stopped complaining about the certificate. (The CLOSE_WAIT sockets above were from before I made this change, and went away after.) I don't think this is related, as the same problem should exist for everyone, but it might be. This is the second time this user has had this problem. The first time, I never found a solution other than reinstalling Outlook. Now that it's a pattern, I'd like to find a permanent solution, rather than assume it's a random glitch.

    Read the article

  • Exchange 2003 calendar's "far" future is blank when scheduling

    - by wfaulk
    If a user tries to schedule a meeting in the "far" future, where ""far" future" seems to mean "seven or more weeks into the future", no existing meetings show up, and resources (at least) frequently (if not always) show up with the white-with-black-hatching "No Information" indicator in the meeting creation window, but shows up fine if you look at the actual calendar from the main Outlook window. Is this expected behavior? If so, is there any way to extend how far out Exchange/Outlook will look?

    Read the article

  • Sun Grid Engine (SGE) / limiting simultaneous array job sub-tasks

    - by wfaulk
    I am installing a Sun Grid Engine environment and I have a scheduler limit that I can't quite figure out how to implement. My users will create array jobs that have hundreds of sub-tasks. I would like to be able to limit those jobs to only running a set number of tasks at the same time, independent of other jobs. Like I might have one array job that I want to run 20 tasks at a time, and another I want to run 50 tasks at a time, and yet another that I'm fine running without limit. It seems like this ought to be doable, but I can't figure it out. There's a max_aj_instances configuration option, but that appears to apply globally to all array jobs. I can't see any way to use consumable resources, as I'd need a "complex attribute" that is per-job, and that feature doesn't seem to exist. It didn't look like resource quotas would work, but now I'm not so sure of that. It says "A resource quota set defines a maximum resource quota for a particular job request", but it's unclear if an array job's sub-tasks' resource requests will be aggregated for the purposes of the resource quota. I'm going to play with this, but hopefully someone already knows outright.

    Read the article

  • How can I force a Mac OS X kext to load prior to login?

    - by wfaulk
    I have a kext that I would like to be loaded at startup time. It doesn't need to be loaded particularly early in the process, but I would like it to be loaded before a user logs in. The kext in question is InsomniaT, and, unlike a device driver, there is nothing that is automatically going to request that it be loaded into the kernel, so just putting it in /System/Library/Extensions won't do anything. What's the best way to do this?

    Read the article

  • Exchange 2003 automatically converts text/plain emails to text/html for IMAP retrieval

    - by wfaulk
    When accessing an Exchange 2003 server via IMAP, emails that were sent as text/plain (and ones that had no MIME encoding specified at all) get automatically converted to multipart/alternative with the original text/plain body and a text/html body. This is … stupid. It doesn't even bother to specify a monospaced font. The new MIME part starts like this: Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2//EN"> <HTML> <HEAD> <META HTTP-EQUIV=3D"Content-Type" CONTENT=3D"text/html; = charset=3Diso-8859-1"> <META NAME=3D"Generator" CONTENT=3D"MS Exchange Server version = 6.5.7654.12"> <TITLE>{{subject}}</TITLE> </HEAD> <BODY> <!-- Converted from text/plain format --> <BR> <P><FONT SIZE=3D2>{{body}} (All the "3D" stuff is quoted-printable encoding for an equals sign; there's nothing wrong on that front, surprisingly.) How can I make this stop?

    Read the article

  • txt file descriptor in lsof

    - by wfaulk
    In my experience, files that have the file descriptor of txt in lsof output are the executable file itself and shared objects. The lsof man page says that it means "program text (code and data)". While debugging a problem, I found a large number of data files (specifically, ElasticSearch database index files) that lsof reported as txt. These are definitely not executable files. The process was ElasticSearch itself, which is a java process, if that helps point someone in the right direction. I want to understand how this process is opening and using these files that gets it to be reported in this way. I'm trying to understand some memory utilization, and I suspect that these open files are related to some metrics I'm seeing in some way. The system is Solaris 10 x86.

    Read the article

1