Search Results

Search found 20188 results on 808 pages for 'wireless network'.

Page 1/808 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Wireless with WEP extremely slow on an Acer Timeline 4810T with a Centrino Wireless-N 1000

  - by noq38

  I've upgraded an Acer Timeline 4810T to Ubuntu 11.10. Everything works fine except for the darn wireless interface (network manager). I just tested the wireless interface over a non-encrypted signal and it works beautifully. The issue is definitely related to WEP. Unfortunately, some of the networks I need to connect to are WEP encrypted, therefore this is a serious issue for me that is preventing me from using Ubuntu on my laptop. This was no problem in 11.04 and prior. Is there a simple solution for this? Any suggestions? Here's more hardware information. Hopefully this helps to debug the network issue: sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:3c:5e:e0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-13-generic-pae firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d2400000-d2401fff lspci 02:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no Many thanks for your help! I just tested the wireless interface over a non-encrypted signal and it works beautifully. The issue is definitely related to WEP. Unfortunately, some of the networks I need to connect to are WEP encrypted, therefore this is a serious issue for me that is preventing me from using Ubuntu on my laptop. Any suggestions?

  Read the article

• That pestky Intel Centrino wireless N + WiMAX 6150 wireless card

  - by newb26

  I'm new to linix and just got Ubuntu up and running on my ASUS laptop last night. Aside from the wireless everything seems to be working. The card is able to recognize networks but cannot make a full connection. After I enter my password it will try to connect before asking for the password again after a few minutes. I know the issue isn't the password because I checked that I had the right one. I've done some poking around trying to find a way to get it work. Linix recognizes the card as well. I found a link to some drivers in a question someone had about a WiMAX 6250 card and am curious if anyone knows if they would also work for the 6150 I have in my machine: https://github.com/ago/wimax-tools If not what can I do?

  Read the article

• Script to setup Ubuntu as a wireless access point on a bridge mode

  - by nixnotwin

  I use the following script to make my netbook a full-fledged wireless access point. It creates a bridge with eth0 and wlan0 and starts hostapd. #!/bin/bash service network-manager stop ifconfig eth0 0.0.0.0 #remove IP from eth0 ifconfig eth0 up #ensure the interface is up ifconfig wlan0 0.0.0.0 #remove IP from eth1 ifconfig wlan0 up #ensure the interface is up brctl addbr br0 #create br0 node hostapd -d /etc/hostapd/hostapd.conf > /var/log/hostapd.log & sleep 5 brctl addif br0 eth0 #add eth0 to bridge br0 brctl addif br0 wlan0 #add wlan0 to bridge br0 ifconfig br0 192.168.1.15 netmask 255.255.255.0 #ip for bridge ifconfig br0 up #bring up interface route add default gw 192.168.1.1 # gateway This script works efficiently. But if I want to revert back to use Network Manager, I cannot do it. The bridge simply cannot be deleted. How can I modify this script so that if I run bridge_script --stop, the bridge gets deleted, network manager starts and interfaces behave as if the machine had a fresh reboot.

  Read the article

• Script to setup ubuntu as a wireless accesspoint on a bridge mode

  - by nixnotwin

  I use the following script to make my netbook a full-fledged wireless accesspoint. It creates a bridge with eth0 and wlan0 and starts hostapd. #!/bin/bash service network-manager stop ifconfig eth0 0.0.0.0 #remove IP from eth0 ifconfig eth0 up #ensure the interface is up ifconfig wlan0 0.0.0.0 #remove IP from eth1 ifconfig wlan0 up #ensure the interface is up brctl addbr br0 #create br0 node hostapd -d /etc/hostapd/hostapd.conf > /var/log/hostapd.log & sleep 5 brctl addif br0 eth0 #add eth0 to bridge br0 brctl addif br0 wlan0 #add wlan0 to bridge br0 ifconfig br0 192.168.1.15 netmask 255.255.255.0 #ip for bridge ifconfig br0 up #bring up interface route add default gw 192.168.1.1 # gateway This script works efficiently. But if I want to revert back to use Network Manager, I cannot do it. The bridge simply cannot be deleted. How can I modify this script so that if I run bridge_script --stop, the bridge gets deleted, network manager starts and interfaces behave as if the machine had a fresh reboot.

  Read the article

• My laptop can not access internet after setup bridge with wired NIC and wireless NIC

  - by Victor S

  I setup a bridge using wired NIC and wireless NIC in order to make wireless NIC as a Wi-Fi AP to share wired internet access, after setup successfully, the Wi-Fi AP works as my expectation, but my laptop can not access internet, please give me a hand. Thanks. My hostapd.conf $ cat hostapd.conf interface=wlan0 bridge=br0 driver=nl80211 ssid=myAP hw_mode=g channel=11 dtim_period=1 rts_threshold=2347 fragm_threshold=2346 macaddr_acl=0 auth_algs=3 ieee80211n=0 wpa=3 wpa_passphrase=PassWord wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP Setup steps: $ sudo killall hostapd hostapd: no process found $ sudo hostapd -B hostapd.conf Configuration file: hostapd.conf Using interface wlan0 with hwaddr 00:26:5e:e8:4f:8e and ssid 'myAP' $ sudo brctl addbr br0 device br0 already exists; can't create bridge with the same name $ sudo ifconfig eth0 0.0.0.0 up $ sudo ifconfig wlan0 0.0.0.0 up $ sudo brctl addif br0 eth0 $ sudo brctl addif br0 wlan0 device wlan0 is already a member of a bridge; can't enslave it to bridge br0. $ sudo ifconfig br0 192.168.1.110 netmask 255.255.255.0 $ sudo route add default gw 192.168.1.1

  Read the article

• Compat Wireless Drivers Centrino N-2230

  - by user2699451

  So I am using linux and am having trouble installing the Compat Wireless drivers Hardware: Intel Centrino N-2230 OS: Linux Mint 64bit (kernel 13.08-generic) I followed this link http://www.mathyvanhoef.com/2012/09/compat-wireless-injection-patch-for.html Output: apt-get install linux-headers-$(uname -r) Reading package lists... Done Building dependency tree Reading state information... Done linux-headers-3.8.0-19-generic is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 19 not upgraded. charles-W55xEU compat-wireless-2010-10-16 # cd ~ charles-W55xEU ~ # dir adt-bundle-linux-x86_64-20130917.zip Desktop known_hosts_backup charles-W55xEU ~ # wget http://www.orbit-lab.org/kernel/compat-wireless-3-stable/v3.6/compat-wireless-3.6.2-1-snp.tar.bz2 --2013-10-29 10:28:23-- http://www.orbit-lab.org/kernel/compat-wireless-3-stable/v3.6/compat-wireless-3.6.2-1-snp.tar.bz2 Resolving www.orbit-lab.org (www.orbit-lab.org)... 128.6.192.131 Connecting to www.orbit-lab.org (www.orbit-lab.org)|128.6.192.131|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 4443700 (4,2M) [application/x-bzip2] Saving to: ‘compat-wireless-3.6.2-1-snp.tar.bz2’ 100%[======================================>] 4 443 700 13,5KB/s in 11m 3s 2013-10-29 10:39:27 (6,55 KB/s) - ‘compat-wireless-3.6.2-1-snp.tar.bz2’ saved [4443700/4443700] charles-W55xEU ~ # tar -xf compat-wireless-3.6.2-1-snp.tar.bz2 charles-W55xEU ~ # cd compat-wireless-3.6-rc6-1 bash: cd: compat-wireless-3.6-rc6-1: No such file or directory charles-W55xEU ~ # dir adt-bundle-linux-x86_64-20130917.zip Desktop compat-wireless-3.6.2-1-snp known_hosts_backup compat-wireless-3.6.2-1-snp.tar.bz2 charles-W55xEU ~ # cd compat-wireless-3.6.2-1-snp/ charles-W55xEU compat-wireless-3.6.2-1-snp # dir code-metrics.txt defconfigs linux-next-pending pending-stable compat drivers MAINTAINERS README config.mk enable-older-kernels Makefile scripts COPYRIGHT include net udev crap linux-next-cherry-picks patches charles-W55xEU compat-wireless-3.6.2-1-snp # wget http://patches.aircrack-ng.org/mac80211.compat08082009.wl_frag+ack_v1.patch --2013-10-29 10:40:52-- http://patches.aircrack-ng.org/mac80211.compat08082009.wl_frag+ack_v1.patch Resolving patches.aircrack-ng.org (patches.aircrack-ng.org)... 213.186.33.2, 2001:41d0:1:1b00:213:186:33:2 Connecting to patches.aircrack-ng.org (patches.aircrack-ng.org)|213.186.33.2|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1049 (1,0K) [text/plain] Saving to: ‘mac80211.compat08082009.wl_frag+ack_v1.patch’ 100%[======================================>] 1 049 --.-K/s in 0s 2013-10-29 10:40:56 (180 MB/s) - ‘mac80211.compat08082009.wl_frag+ack_v1.patch’ saved [1049/1049] charles-W55xEU compat-wireless-3.6.2-1-snp # patch -p1 < mac80211.compat08082009.wl_frag+ack_v1.patch patching file net/mac80211/tx.c Hunk #1 succeeded at 792 (offset 115 lines). charles-W55xEU compat-wireless-3.6.2-1-snp # wget -Ocompatwireless_chan_qos_frag.patch http://pastie.textmate.org/pastes/4882675/download --2013-10-29 10:43:18-- http://pastie.textmate.org/pastes/4882675/download Resolving pastie.textmate.org (pastie.textmate.org)... 178.79.137.125 Connecting to pastie.textmate.org (pastie.textmate.org)|178.79.137.125|:80... connected. HTTP request sent, awaiting response... 301 Moved Permanently Location: http://pastie.org/pastes/4882675/download [following] --2013-10-29 10:43:20-- http://pastie.org/pastes/4882675/download Resolving pastie.org (pastie.org)... 96.126.119.119 Connecting to pastie.org (pastie.org)|96.126.119.119|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 2036 (2,0K) [application/octet-stream] Saving to: ‘compatwireless_chan_qos_frag.patch’ 100%[======================================>] 2 036 --.-K/s in 0,001s 2013-10-29 10:43:21 (3,35 MB/s) - ‘compatwireless_chan_qos_frag.patch’ saved [2036/2036] charles-W55xEU compat-wireless-3.6.2-1-snp # patch -p1 < compatwireless_chan_qos_frag.patch patching file drivers/net/wireless/rtl818x/rtl8187/dev.c patching file net/mac80211/tx.c Hunk #1 succeeded at 1495 (offset 8 lines). patching file net/wireless/chan.c charles-W55xEU compat-wireless-3.6.2-1-snp # make ./scripts/gen-compat-autoconf.sh /root/compat-wireless-3.6.2-1-snp/.config /root/compat-wireless-3.6.2-1-snp/config.mk > include/linux/compat_autoconf.h make -C /lib/modules/3.8.0-19-generic/build M=/root/compat-wireless-3.6.2-1-snp modules make[1]: Entering directory `/usr/src/linux-headers-3.8.0-19-generic' CC [M] /root/compat-wireless-3.6.2-1-snp/compat/main.o LD [M] /root/compat-wireless-3.6.2-1-snp/compat/compat.o CC [M] /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.o In file included from /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma.h:8:0, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/bcma_private.h:8, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:8: /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma_driver_pci.h:217:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_core_pci_init’ In file included from /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma.h:10:0, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/bcma_private.h:8, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:8: /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma_driver_gmac_cmn.h:95:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_core_gmac_cmn_init’ In file included from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:8:0: /root/compat-wireless-3.6.2-1-snp/drivers/bcma/bcma_private.h:25:15: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_bus_register’ /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:152:15: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_bus_register’ /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:17:21: warning: ‘bcma_bus_next_num’ defined but not used [-Wunused-variable] /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:93:12: warning: ‘bcma_register_cores’ defined but not used [-Wunused-function] make[3]: *** [/root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.o] Error 1 make[2]: *** [/root/compat-wireless-3.6.2-1-snp/drivers/bcma] Error 2 make[1]: *** [_module_/root/compat-wireless-3.6.2-1-snp] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.8.0-19-generic' make: *** [modules] Error 2 charles-W55xEU compat-wireless-3.6.2-1-snp # make install Warning: You may or may not need to update your initframfs, you should if any of the modules installed are part of your initramfs. To add support for your distribution to do this automatically send a patch against ./scripts/update-initramfs. If your distribution does not require this send a patch against the '/usr/bin/lsb_release -i -s': LinuxMint tag for your distribution to avoid this warning. make -C /lib/modules/3.8.0-19-generic/build M=/root/compat-wireless-3.6.2-1-snp modules make[1]: Entering directory `/usr/src/linux-headers-3.8.0-19-generic' CC [M] /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.o In file included from /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma.h:8:0, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/bcma_private.h:8, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:8: /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma_driver_pci.h:217:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_core_pci_init’ In file included from /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma.h:10:0, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/bcma_private.h:8, from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:8: /root/compat-wireless-3.6.2-1-snp/include/linux/bcma/bcma_driver_gmac_cmn.h:95:23: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_core_gmac_cmn_init’ In file included from /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:8:0: /root/compat-wireless-3.6.2-1-snp/drivers/bcma/bcma_private.h:25:15: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_bus_register’ /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:152:15: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘bcma_bus_register’ /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:17:21: warning: ‘bcma_bus_next_num’ defined but not used [-Wunused-variable] /root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.c:93:12: warning: ‘bcma_register_cores’ defined but not used [-Wunused-function] make[3]: *** [/root/compat-wireless-3.6.2-1-snp/drivers/bcma/main.o] Error 1 make[2]: *** [/root/compat-wireless-3.6.2-1-snp/drivers/bcma] Error 2 make[1]: *** [_module_/root/compat-wireless-3.6.2-1-snp] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.8.0-19-generic' make: *** [modules] Error 2 charles-W55xEU compat-wireless-3.6.2-1-snp # It keeps giving errors, same with other sites, I get the same errors??? I am lost, help needed

  Read the article

• No Wireless In Ubuntu 13.10 (maybe Need Wireless Driver) [duplicate]

  - by viktorhubinette

  This question already has an answer here: No Wireless In Ubuntu 13.10 2 answers hi after updating to ubuntu 13.10 i cant see the wireless networks on the network meny so what should i do ? tell me some commands you need to see to solve the problem. Thanks (i maybe need a wireless driver becouse i installed one when i haved 12.04 becouse i could not connect to wireless before too) i cant connect to wireless that my problem so what do i need to do to get this wireless working again? some outputs lsmod | grep rt1 nothing sudo modprobe rt18192cu FATAL: Module rt18192cu not found. iwconfig eth0 no wireless extensions. lo no wireless extensions. sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning. rfkill list all nothing

  Read the article

• wireless detected but Can't connect to network, Wifi card intel pro wireless N100 BGN

  - by Alexandre777

  Thanks in advance, I installed Linux Mint kernel 3.0.0-12 x64 ,wireless is detected and I configure it in network manager but can't coonect, there are the results of command line: $ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ sudo lshw -C network** *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:51:c9:d6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:d7400000-d7401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:5b:39:99:8f:16 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Thank you.

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• Good Wireless Range Extender

  - by Joseph Sturtevant

  Can anyone recommend a good wireless (802.11g) range extender? I would like to find something that will provide reliable wireless to areas of the building that aren't covered or get poor reception. I would also like a product that won't require big changes to my current wireless setup (multiple APs with a wireless controller are out). Latency and bandwidth aren't terribly important. Does anyone have experience with a product like this?

  Read the article

• Using airport extreme base station as a wireless G to wireless N bridge

  - by micmcg

  Due to unfortunate placement of various wall outlets in my new apartment, my adsl 2 modem + router is not able to be placed next to my airport extreme base station (AEBS). I'd prefer not to run cat5 cable between them, but I still want to use the wireless N on the AEBS, because it will have a high speed NAS plugged in via gigabit ethernet so I want to maximise the wireless transfer speed to my 27" iMac. Is it possible to use one of the radios in the airport extreme to bridge the wireless G network with the router, and the wireless N radio to broadcast normally? The only traffic going over the G network should be internet (24mbps ADSL2) so it should never get saturated. Thanks

  Read the article

• Missing Wireless access point

  - by nvcnvn

  I have an: Ubuntu 12.04 with proprietary Boardcom STA Wireless driver installed BCM43224 802.11a/b/g/n wireless card TP-LINK TD-W8101G 54Mbps Wireless ADSL2+ Modem Router Yesterday before I went to sleep, I still connect to my wireless access point, this morning when I start my laptop I don't see it in the list - there are some neighbors listed but not mine. The WLAN is green, with my old Nokia E72, I still see my access point with 100% signal. I have tried to restart my laptop and turn the firmware off/on by the switch but no help. I have read the WirelessTroubleShootingGuide but I can do anything. Here is some of my card info: *-network description: Wireless interface product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: c0:cb:38:06:5d:53 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 03 serial: f0:4d:a2:42:ab:e4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:5000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff memory:f0420000-f043ffff

  Read the article

• Create personal wireless network on laptop

  - by TechGuru

  I have a WiFi Network, now I have connected my laptop to the WiFi Network. And it is working fine I'm able to access the internet via WiFi. But I want to create other network on my laptop so that I can connect my mobile phone to the my laptop network. Means, my laptop is already connected to WiFi network (xyz). Now I want to create one wireless network on my laptop. So that I can connect my mobile phone to laptop network and access the internet on mobile. But I don't want to lost my `laptop and WiFi connection that is already connected. I tried to create the wireless network on my laptop, but when I created my personal wireless network I lost my wifi-laptop connection. I don't know it is possible or not.

  Read the article

• How practical is using a Wireless-N router together with a B and G router?

  - by Jian Lin

  I hope to use a Wireless N router to boost up the speed of wireless Internet, but there are some device that probably only supports B or G, such as iPhone, iPad, Wii, so if it is to replace the existing Wireless-B/G router, then some device won't work. Is it practical to buy a Wireless-N router, and then just plug the existing wireless router to it, or if I am using AT&T's u-verse, which has a central Wireless-B/G router, then plug in a new Wireless-N router into it?

  Read the article

• Use 2 wireless adapters to connect to 2 WIFI networks (local and internet) simultaneously?

  - by Mouad

  On my HP Compaq 6710b there's an internal WIFI network adapter. Attached to the same laptop there's also an external USB Alfa WIFI adapter. I live near campus and can pick it's WIFI signal. The problem is that when I am connected to the Internet Wifi using the internal adapter, and then connect to the home (non-internet) Wifi network's router, I lose the connection to the internet (it stays connected, but there's no actual connection). So how can I use the two adapters to connect to both networks successfully ? The router is Belkin N150 Enhanced Router Model F6D4230-4 V1 The external adapter is: ALFA AWUS 036NHR

  Read the article

• Wireless Drivers for Broadcom BCM 4321 (14e4:4329) will not stay connected to a wireless network

  - by Eugene

  So, I'm not necessary new to Linux, I just never took the time to learn it, so please, bare with me. I just swapped out one of my wireless cards from one computer to another. This wireless card in question would be a "Broadcom BCM4321 (14e4:4329)" or actually a "Netgear WN311B Rangemax Next 270 Mbps Wireless PCI Adapter", but that's not important. I've tried (but probably screwed up in the process) installing the "wl" , "b43" and "brcmsmac" drivers, or at least I think I did. Currently I have only the following drivers loaded: eugene@EugeneS-PCu:~$ lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" b43 387371 0 bcma 52096 1 b43 mac80211 630653 1 b43 cfg80211 484040 2 b43,mac80211 ssb_hcd 12869 0 ssb 62379 2 b43,ssb_hcd The main issue is that with most of the drivers available that I've installed, they will find my wireless network but, they will only stay connected for about a minute with abnormally slow speed and then all of a sudden disconnect. Currently, the computer is hooked into another to share it's connect so that I can install drivers from the internet instead of loading them on to a flash drive and doing it offline. If anyone has any insight to the problem, that would be awesome. If not, I'll probably just look up how to install the Windows closed source driver. Edit 1: Even when I try the method here, as suggested when this was marked as a duplicate, I still can't stay connected to a wireless network. Edit 2: After discussing my issue with @Luis, he opened my question back up and told me to include the tests/procedures in the comments. Basically I did this: Read the first answer of the link above when this question was marked as duplicate which involved installing removing bcmwl-kernel-source and instead install firmware-b43-installer and b43-fwcutter. No change of result and contacted Luis in the comments, who then told me to try the second answer which involved removing my previous mistake and installing bcmwl-kernel-source Now the Network Manger (this has happend before, but usally I fixed it by using a different driver) even recognizes WiFi exist (both non-literal and literal). Luis who then suggested sudo rfkill unblock all rfkill unblock all didn't return anything, so I decide to try sudo rfkill list all. Returns nothing (no wonder rfkill unblock all did nothing). I enter lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" and that returns nothing. Try loading the driver by entering sudo modprobe b43 and try lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" again. Returns this: eugene@Eugenes-uPC:~$ sudo modprobe b43 eugene@Eugenes-uPC:~$ lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" b43 387371 0 bcma 52096 1 b43 mac80211 630653 1 b43 cfg80211 484040 2 b43,mac80211 ssb_hcd 12869 0 ssb 62379 2 b43,ssb_hcd So to recap: Currently Network Manager doesn't recognize Wireless exists, b43 drivers are loaded and I've currently hardwired a connect from my laptop to the computer that's causing this.

  Read the article

• repeated request for wireless password, no wireless connection

  - by Tris

  whenever i try to connect to a wireless network, ubuntu (11.10) asks for the password. when i enter this it thinks for a couple of minutes, then asks for the password again. This happens repeatedly. (it isn't a problem with the wireless modem itself, as i can connect to wireless from the windows 7 opererating system i have running along side ubuntu. If anyone has any ideas about how to fix this they would be much appreciated! Thanks

  Read the article

• How to set Ubuntu as wireless accespoint in the GUI way?

  - by Agmenor

  My aim is to make my Ubuntu machine be a wireless accesspoint using wifi. Of course I found two AskUbuntu questions already treating that; this one and that one. Nevertheless, as far as I am concerned I would like to set up such a network in the Graphical User Interface (GUI) way. Please avoid solutions with the command line. So a solution suggesting to use Network Manager would be really welcomed. Please name and describe very precisely each step, so I can easily find the equivalent in my own language. Thank you for your answers!

  Read the article

• Belking Wireless Router unable to connect to internet although wireless connection is working

  - by ptamzz

  I have a Belkin Basic N150 Wireless router. I'm trying to set up wireless connection using the wired ports my university has provided in my hostel room. Usually, when I connect my laptop using a LAN wire through the port, my settings are like IP: 10.5.130.X Subnet Mask: 255.255.254.0 Default Gateway: 10.5.130.250 DNS Server: 10.200.1.11 and I'm able to connect to the internet. Now instead of connecting my laptop directly, I've connected the lan wire to the Belkin Wireless Router, set the router as "Use as an Access Point" and in the IP field, I've put up 10.5.130.1. Now I've set the IP of my system manually to 10.5.130.3. I'm able to connect to the wi-fi but I'm still not able to connect to the internet. What am I missing?

  Read the article

• Centrino Wireless-N 1000 takes forever to connect and keeps asking for password

  - by waclock

  A few days ago I started having this problem. When I tried to connect to any WiFi Connection it would stay connecting forever, and after a minute or so it would ask me for the password again. The strange thing is that this happened out of nowhere, I did not install any new drivers or anything like that. After this happened I decided to uninstall ubuntu and install it again ("inside windows") but the problem is still there. Any suggestions would be greatly appreciated. 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:aa:e4:7d size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:50 ioport:4000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:09:9c:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-23-generic-pae firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:c4500000-c4501fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.2 logical name: eth1 serial: ee:85:2f:7d:80:96 capabilities: ethernet physical configuration: broadcast=yes driver=ipheth ip=172.20.10.2 link=yes multicast=yes

  Read the article

• What device can create wireless network while connecting to an ethernet router

  - by Nicolo

  Hi, I have access to an ethernet port of a wireless router. I simply connect my laptop to it via an ethernet cable. There are a total of four such ports on the wireless router. Now I want to connect a device (a wireless access point? wireless bridge? wireless switch?) via an ethernet cable to one of the other ethernet ports of the router. I want this device to act as a kind of wireless switch - it should "split" the ethernet connection coming from the router to two or more computers that connect to this device via a wireless. Basically, I have a wireless router with its wireless function switched off. I don't know the password for that router so can't activate the wireless function. Don't know the password of the ISP either. The only thing I can do is to connect via ethernet cable to the wireless router and this does not require a password. Now I want to use that connection and build a wireless upon it. What kind of device do I need? I am not really very well informed about network management and find the descriptions "wireless access point", "wireless bridge", "wireless switch" confusing. I know what an ethernet switch is - what I need is a device which would do the same but by allowing the clients to connect to it via a wireless. What kind of device would do that? Any recommendations about specific products?

  Read the article

• Existing open source software for wireless mesh networking?

  - by user70352

  Hello! My goal: Build a wireless mesh network with some ALIX 2D2 (500 MHz AMD Geode LX800 x86 CPU, 256MB RAM, Atheros wireless card) Aside from working like a normal wireless mesh network users should be able to read/write data from/to the ALIX Boxes and the ALIX boxes should be able to process data. Questions: Should I try to flash dd-wrt x86, voyage linux (linux.voyage.hk) or something else? What (open source) software should I look into before I start? Should I use a 'server' for data storage and processing instead of the ALIX boxes? Is it even possible to use the ALIX boxes for routing AND data storage and processing? Final notes: Data can be anything, for example, I want to setup a wireless mesh using the OLSRD protocol so my whole town gets wifi and can access songs on the network. It's not for that, but that's the idea. I'm not afraid of programing, compiling or working with *nix. This is mostly 'for fun' rather than for practicality. Thanks in advance for any feedback.

  Read the article

• Wireless not working on XP (with Intel® PRO/Wireless 2200BG Network Connection card and Zyxel router

  - by JohnIdol

  Hi all, I just got a new router, cant' get my old xp laptop (Toshiba Satellite) to connect to it, no matter if it's WPA-PSK or WEP (I was kind of thinking with WEP it would've worked but it doesn't). When I go connect and put in credentials the dialog stays up for a few minutes then disappears with no message and no connection is established. Here's the spec of router and wireless card: Wilreless card: Intel® PRO/Wireless 2200BG Network Connection Router: Zyxel P-660-HW-T1 v3 Everything works fine on my Vista machine (for once). Any help appreciated!

  Read the article

• creating a 802.11n wireless network between laptops and asus n-13 wireless adapter

  - by xpugur

  I have a asus usb n-13 wireless adapter and 3 laptops in a home we try to create a network witn 802.11n standards but failed each time laptops have intel 5100 agn. We try to create network with wpa-2 personal encryption that also fails(couldn't connect) but with wep encryption connects but with 802.11g standard... so do you know how to create a 802.11N based network? ... thank you...

  Read the article

• Frequent Disconnects with an Intel 3945ABG Wireless Card

  - by Alex Forsythe

  I'm brand new to Ubuntu, and I really love it so far, but one issue I have encountered is that my WLAN is disconnecting about every 5-10 minutes. Often times the connection is repaired automatically, but sometimes the network manager will repeatedly reject my encryption key (which of course is correct). Occasionally after a disconnect, the wireless network fails to show up at all. The only way I can solve this seems to be by completely restarting Ubuntu or connecting with a USB wireless adapter. I am using WPA/WPA2 encryption, which I've read can cause problems with network-manager, but I experience the exact same issues with WICD. I should probably note that I've not experienced any of these issues using Windows 7 on my other partition. I have a hunch that there may be a better driver out there for my card, but I have no idea how to go about searching for it or installing it. Any help would be really appreciated! lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric lspci -nnk 09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express [14e4:1600] (rev 02) Subsystem: Dell Device [1028:0201] Kernel driver in use: tg3 Kernel modules: tg3 0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02) Subsystem: Intel Corporation Device [8086:1020] Kernel driver in use: iwl3945 Kernel modules: iwl3945 rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 3: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >