Openfiler RAID 10 option not found

Posted by chrisling106 on Server Fault See other posts from Server Fault or by chrisling106
Published on 2010-05-04T08:23:40Z Indexed on 2010/05/04 8:28 UTC
Read the original article Hit count: 357

Filed under:

openfiler

|

software-raid

Hi,

I'm building a NAS using Openfiler2.3 (from 32-bit ISO), first of all I want to experiment it on VM first before going out and buy the harddrives needed.

I created 5 virtual drives on VMware, sda is 2GB and the rest 1GB each (sdb to sde).

I left sda blank and want to setup a RAID 10 disk using sdb, sdc, sdd and sde, 4 RAID partitions are setup successfully, but when I try to create a RAID device the only option for RAID level is 1, 0, 5 and 6.

RAID 10 is not there!

Can someone let me know what have I missed, please?

TIA.

© Server Fault or respective owner

Related posts about openfiler

Poor NFS Performance: OpenFiler

as seen on Server Fault - Search for 'Server Fault'
Good Day Everyone, I have an issue with OpenFiler, a Linux-based operating that converts a computer system into a SAN/NAS appliance. Here is the problem. In my environment we have two Netapp Storevault 500 appliances that I normally perform backups to a NFS share. There are two backup cronjobs that… >>> More
Performance stats for ESXi VMs on Openfiler NFS

as seen on Server Fault - Search for 'Server Fault'
Hi there, AFAIK VMWare utilise it's own filesystem vmfs for performance and efficiency reasons. What will that be if I host my VMs on an Openfiler server which setup as NAS using ext3 filesystem? Thanks >>> More
OpenFiler cannot delete volume group

as seen on Server Fault - Search for 'Server Fault'
I have deleted all the ingredients of a volume group even access options, but it still says that the Volume Group is in use. I tried to close everything including the OpenFiler itself but when I open it, it still says the volume is in use. How can I overcome this problem ? Thanks >>> More
Openfiler RAID 10 option not found

as seen on Server Fault - Search for 'Server Fault'
Hi, I'm building a NAS using Openfiler2.3 (from 32-bit ISO), first of all I want to experiment it on VM first before going out and buy the harddrives needed. I created 5 virtual drives on VMware, sda is 2GB and the rest 1GB each (sdb to sde). I left sda blank and want to setup a RAID 10 disk using… >>> More
[Openfiler] How to create new ftp users?

as seen on Server Fault - Search for 'Server Fault'
Hi there, There's only a default ftp user assigned in openfiler ftp service - openfiler/password. I've been pulling my hairs out for trying to add users to the ftp server but without any luck. I have turned on the local LDAP server within Openfiler and add users there and still no luck. It's for… >>> More

Related posts about software-raid

Linux Software RAID-1 in production environment

as seen on Server Fault - Search for 'Server Fault'
Is it recommended to use software RAID-1 in a production environment? Due to budget constraints, I cannot get a hardware RAID controller for a new server. While I'm aware of a slight performance decrease, is it really that much of a difference? >>> More
How to install Windows 7 onto software RAID-0

as seen on Super User - Search for 'Super User'
I recently got a new laptop (Asus G73JH-A2) which has two identical hard drives in it. Unfortunately the motherboard does not have a RAID controller. What I would like to do is run the drives in a RAID-0 configuration to improve performance (plus get the extra capacity on one partition). I would… >>> More
Problems migrating software RAID 5 to new server (linux)

as seen on Server Fault - Search for 'Server Fault'
I have a CentOS setup with sw RAID5 that holds my data. Well, the server died, so I bought another box to migrate my drives to. Only thing is, I cannot get the RAID array rebuilt (not even sure it needs rebuilding, might just need the /dev/md0 mapping created... but I don't even know how to determine… >>> More
Linux boot on a raid1 software raid ?

as seen on Server Fault - Search for 'Server Fault'
Hello I am trying to convert my single disk boot to a raid1 boot So far here is what i have: I sucessfully create the raid 1 as degraded with the new drive alone, I copied all the data on it I can mount that raid 1, see its files etc I already have a raid5 that is working on the same box (although… >>> More
Mac OS X Server 10.6 - Apple's software mirrored RAID worth it?

as seen on Server Fault - Search for 'Server Fault'
Hi, I am installing an Intel Xserve (Quad core Xeon) with Snow Leopard Server (10.6) on two 80Gb 7200rpm SATA HDs. I created a mirrored RAID set using Disk Utility with those two drives, all went fine. I was then asking myself if this is really a good idea. I know that an hardware RAID system would… >>> More