Posted
by kmanjar
on Stack Overflow
See other posts from Stack Overflow
or by kmanjar
Published on 2010-06-09T20:09:16Z
Indexed on
2010/06/09
20:12 UTC
Read the original article
Hit count: 168
When a GSM modem is receiving voice(i.e., multiple wave files continuously) in the voice path, how will the modem able to identify the completion of a single wave file? Is there any software that could perform this?
© Stack Overflow or respective owner
as seen on Ask Ubuntu
- Search for 'Ask Ubuntu'
My modem isn't in the device list of usb_modeswitch....
so I cannot automatically use the modem on the ubuntu....
I found the way to change the modem from usb storage mode to modem mode and I can use my modem.
But I forgot the instructions.
I don't know the modem's name. It's chinese modem.
But here…
>>> More
as seen on Ask Ubuntu
- Search for 'Ask Ubuntu'
I am using Beagleboard-xm with 3.12 Kernel and ubuntu rootfs from Robert Nelson's site.
I use a Telit HE910 GPS+GSM modem along with my project .So as per the HW user guide i have to apply a logic high for 5s on the input of this modem for enabling it
So when I does this by toggling the gpio pin…
>>> More
as seen on Ask Ubuntu
- Search for 'Ask Ubuntu'
I want to configure EVDO Usb Modem in Ubuntu 10.10
I insert my usb modem to laptop and check the usb is detected or not using $sudo lsusb and the result is:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device…
>>> More
as seen on Ask Ubuntu
- Search for 'Ask Ubuntu'
I want to configure EVDO Usb Modem in Ubuntu 10.10
I insert my usb modem to laptop and check the usb is detected or not using $sudo lsusb and the result is:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device…
>>> More
as seen on Super User
- Search for 'Super User'
I am using MTS datacard. I have usb_modeswitch installed and have configured the wvdial.conf file. When I do sudo wvdial cdma, the IPs and DNS addresses are also allocated but I still cant access internet.
The reply to dmesg | grep -e 'tty' -e 'modem' is:
[ 0.000000] console [tty0] enabled
[…
>>> More
as seen on Stack Overflow
- Search for 'Stack Overflow'
Dear All,
I have one GSM Modem Series 900. I want to test it for sending and receiving message to mobile. I can connect with this modem, but when I put my SIM Card and I type AT command like here:
AT: Status "OK"
AT+CPIN?: Status "+CPIN: PH-NET PIN"
AT+CPIN="xxxx": Status "Error"
I don't know why…
>>> More
as seen on Stack Overflow
- Search for 'Stack Overflow'
Does anyone know how to convert GSM audio into PCM WAV via C#? I have tried to find a viable solution on the Internet to no avail.
>>> More
as seen on Stack Overflow
- Search for 'Stack Overflow'
Has anyone measured the rate of submission through a GSM modem? We are implementing a solution at the moment and are only able to submit at a rate of about one message every 3 to 5 seconds. We are not sure if this is a library/api problem or if our modem is just of poor quality. Has anyone had any…
>>> More
as seen on Stack Overflow
- Search for 'Stack Overflow'
Hi
Im new with Objective C but a veteran of C# & VB.Net. Is there an available API or functionality in cocoa where i can communicate with my GSM Phone to listen to any incoming SMS messages and be able to send messages myself. I'm trying to build an application for OSX SnowLeopard that can do…
>>> More
as seen on Ask Ubuntu
- Search for 'Ask Ubuntu'
i've got problem with e160 on ubuntu 12.04. I'cant configure network manager and connect because NM can't see the e160. I;ve tried lot of solutions with no result.
ateusz@mateusz-Aspire-5738:~$ sudo usb_modeswitch -v 0x12d1 -p 0x1003 -H
[sudo] password for mateusz:
aLooking for default devices…
>>> More
