Colocation and HSRP setup

Posted by WinkyWolly on Server Fault See other posts from Server Fault or by WinkyWolly
Published on 2012-10-31T22:46:51Z Indexed on 2012/10/31 23:03 UTC
Read the original article Hit count: 222

Filed under:

networking

|

hsrp

My colocation provider has setup HSRP for us and has provided us 2 drops (plugged into 1/1/1 and 1/1/2) from their routers as well as a /29 with 2 HSRP IP's and the rest of the /29 usable for the switch.

I know that HSRP should be pretty much plug and play as long as the ports are in the same VLAN.

However I'm confused as to how to the IP setup should work.

Currently I've assigned port 1/1/1 the full /29 however I think this is incorrect because if I were to unplug it port 1/1/2 wouldn't work as it has no IP assignment.

What's the proper way to do this?

© Server Fault or respective owner

Related posts about networking

Networking stopped working on Ubuntu

as seen on Super User - Search for 'Super User'
I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the… >>> More
Troubles with start up defenition of networking service in Ubuntu

as seen on Super User - Search for 'Super User'
I use Ubuntu 12.04.1. I put attention that networking script starting in runlevel 0: user@comp:/etc/rc0.d$ chkconfig -l networking networking 0:on 1:off 2:off 3:off 4:off 5:off 6:off When I try to move it working to appropriate run levels I get error: user@comp:/etc/rc0… >>> More
Installing the Elgg Social Networking CMS

as seen on Internet.com - Search for 'Internet.com'
One Open Source CMS that stands out above the rest for small businesses and personal networks is the Elgg open source "social engine," which can be used to create social applications. Scott Clark shows you how to install and get started with this social networking CMS. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More

Related posts about hsrp

Colocation and HSRP setup

as seen on Server Fault - Search for 'Server Fault'
My colocation provider has setup HSRP for us and has provided us 2 drops (plugged into 1/1/1 and 1/1/2) from their routers as well as a /29 with 2 HSRP IP's and the rest of the /29 usable for the switch. I know that HSRP should be pretty much plug and play as long as the ports are in the same VLAN… >>> More
Confusion about HSRP Groups

as seen on Server Fault - Search for 'Server Fault'
If I have a router that has several LANs on it, and each of these LAN is attached to a second router, do I need to use different HSRP groups for each LAN? With this set up, each virtual gateway will be on a Layer 2 segment. And within a router, no interface will have multiple gateways. So, For… >>> More
Cisco Switching Module and HSRP interface Tracking

as seen on Server Fault - Search for 'Server Fault'
When using 4 port switching module where each port is configured to switchport access vlan ##, for HRSP should I track the vlan interface or the FastEthernet interface? interface FastEthernet0/0/0 switchport access vlan 10 interface Vlan10 ip address 12.12.12.1 255.255.255.0 int FastEthernet0/1 … >>> More
Can I have more than two routers in the same HSRP group?

as seen on Server Fault - Search for 'Server Fault'
I want to know if it is possible to do HSRP with 3 or more routers. >>> More
cisco 2900xl - SNMP - Get mac address of device connected to an interface

as seen on Server Fault - Search for 'Server Fault'
Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch… >>> More