ASA 5505 8.4 open ports for subnet

Posted by fwrawx on Server Fault See other posts from Server Fault or by fwrawx
Published on 2012-11-07T23:20:14Z Indexed on 2012/11/11 11:08 UTC
Read the original article Hit count: 353

Filed under:

firewall

|

cisco-asa

I have an ASA 5505 running 8.4 with its outside interface plugged into our internal network. I want to open up access to hosts on one of the vlans behind that ASA to hosts on our internal network. I was just starting to grasp NAT on our older PIX but the ASA 8.4 has me confused now. Given a clean ASA with an outside vlan of 10.0.0.1/24 and test vlan of 10.0.1.1/24 what's the basic configuration needed to allow any hosts on the outside network to have access to any of the hosts on the test network?

© Server Fault or respective owner

Related posts about firewall

Managed hosting firewall vs managing own firewall

as seen on Server Fault - Search for 'Server Fault'
I posted on stackoverflow as to the overall benefits of managed hosting vs non-managed hosting. The more I think about it, it seems to boil down to one question: should I use a managed host because they take care of the firewall, or would I be okay managing my own, software firewall? The sites… >>> More
Hardware firewall vs VMWare firewall appliance

as seen on Server Fault - Search for 'Server Fault'
We have a debate in our office going on whether it's necessary to get a hardware firewall or set up a virtual one on our VMWare cluster. Our environment consists of 3 server nodes (16 cores w/ 64 GB RAM each) over 2x 1 GB switches w/ an iSCSI shared storage array. Assuming that we would be dedicating… >>> More
Firewall behind firewall

as seen on Server Fault - Search for 'Server Fault'
I've recently changed jobs and I've been set up with a new workstation. On all previous places where I've been working they've had some sort of local firewall installed on each and every workstation - but here I've been told not to activate it because it is not necessary since we're already behind… >>> More
We have no SW Firewall behind our office HW firewall, admin says its not req'd

as seen on Server Fault - Search for 'Server Fault'
I've recently changed jobs and I've been set up with a new workstation. On all previous places where I've been working they've had some sort of local firewall installed on each and every workstation - but here I've been told not to activate it because it is not necessary since we're already behind… >>> More
Can't get FTP to work on centOS 5.6

as seen on Server Fault - Search for 'Server Fault'
Hi guys I have been trying for a few hours to install and get FTP to work... I did yum install ftp and yum install vsftpd They all installed and are running but when I try to use filezilla or some other client I just can't connect....I've tried connecting on port 21 and port 990 ....nothing! These… >>> More

Related posts about cisco-asa

Cisco ASA bonding/teaming/port-channel capabilities

as seen on Server Fault - Search for 'Server Fault'
Hello, This seemed to me like a really simple question that I would be able to answer by myself but I have not been able to find any info on this subject. I have a Cisco ASA 5510 which has 4 FastEthernet interfaces. I was wondering if it would be possible to use 2 or 3 of these interfaces as a port-channel… >>> More
Plugging the Cisco ASA Security Hole

as seen on Internet.com - Search for 'Internet.com'
Cisco dominates the networking hardware market, and with its Adaptive Security Appliance it is extending its reach into network security. The ASA, however, can introduce a security issue. Learn how to resolve it so you can get the most out of this powerful tool. >>> More
Enable Cisco ASA as an SSH Tunneling

as seen on Server Fault - Search for 'Server Fault'
I am trying to utilize my Cisco ASA as a SSH Tunnel. I've configured this before when using a Linux server as the SSH target, however I cannot seem to get it to work with the ASA. I have configured and enabled SSH on the Cisco ASA, as well as a username that I can SSH to the console, however the SSH… >>> More
QoS basics on a Cisco ASA

as seen on Server Fault - Search for 'Server Fault'
Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document… >>> More
Configuring Cisco ASA 5510 to assign static IP address based on MAC address

as seen on Server Fault - Search for 'Server Fault'
Hi, We have a CISCO ASA 5510 at work. We want to configure the same such that it can serve specific IP addresses based on the MAC address of the clients. Any help would be greatly appreciated. Thanks in advance -knd >>> More